www.icstation.

com

WHDTS 4-Bit Electronic Clock DIY Kits

1. Introduction
YSZ-4 4-Bit electronic clock is equipped with STC11F02E chip and 16 electronic

components. It can make two alarm clock time, on time alarm (8:00-20:00), accurate

adjustment, etc.

2. Parameter
NO. Parameter Value

1 Operating voltage DC 3V-6V

2 PCB board material RF-4

3 Size 52mm*42mm

3. Principle
The whole system consists of MCU minimum system, key input circuit, display circuit,

buzzer circuit and power supply parts.

1>. MCU minimum system: including the U1 (STC11F02E), C1, R1 for power on reset

circuit .Clock circuit is composed of C2, C3 and Y1.

2>. The pressed key input circuit：composed of S1, S2, short press the button once a

loud buzzer rang, long press the button once two loud buzzer rang.

3>. The display circuit：4bits common cathode and on PR1 Resisters Packs .

4>. Buzzer circuit：composed of Q1, R2 and LS1, short press the button once a loud

buzzer rang, long press the button once two loud buzzer rang.

5>. J1 is 5v power supply input terminal, C4 is filtering.

4. Operation instruction
It will display 12:59 when Power-on, the normal interface is("hours:minutes").

Default the two alarm clock time are opened. The first alarm clock has been set at

13:01 and the second alarm clock has been set at 13:02.

1
 www.icstation.com

Short press S2 after power-on to switch between time-division traveling time interface

("hours:minutes) and minute-second walking time interface ("minutes:seconds”);

Long press S1 to enter the system Settings Menu. There are A, B, C, D, E, F, G, H, I

submenu. Short press S1 submenu to add 1 and finally return to travel time interface.

A sub menu : Correction for hours

Press S2 to increase by 1; After adjusting, press S1 to save and exit this submenu to

enter the B submenu.

B sub menu : Correction for minutes

Press S2 to increase by 1. After adjusting, press S1 to save and exit this submenu to

enter the C submenu.

C sub menu: On time alarm switch

The default state is ON (on-time-alarm is open from 8:00 to 20:00). It will switch

between ON and OFF (on-time-alarm is closed) after press S2. Short press S2 to save

the adjusted results and quit C submenu, enter D submenu.

D sub menu: The first alarm-clock switch

The default state is ON (the first alarm-clock is opened). It will switch between ON and

OFF(first-alarm-clock is closed) after press S2. If it is set to ON, short press S1 to save

and quit, then enter E submenu; If it is set to OFF, short press S1 to save and quit ,

then enter G submenu;

E sub menu: The first alarm clock set for hours

Display data will add 1 after press S2. After adjusting the E Submenu, then short press

S2 to save the adjusted results and quit E submenu, enter F submenu.

F sub menu: The first alarm clock set for minutes

Display data will add 1 after press S2. After adjusting the F submenu, then short press

S2 to save the results and quit F submenu, enter G submenu.

G sub menu: The Second alarm-clock switch

The default state is ON (the second alarm-clock is opened)

It will switch between ON and OFF(second-alarm-clock is closed) when press S2.

If it’s set to ON, short press S1 to save and quit, then enter H submenu;

2
 www.icstation.com

If it’s set to OFF, short press S1 to save and quit, then enter normal interface;

H sub menu: The second alarm clock set for hours

Display data will add 1 after press S2.after adjusted the F Submenu,then short press

S2 to save the adjusted results and quit H submenu,enter I sbumenu.

I Sub menu:The second alarm clock set for hours

Display data will add 1 after press S2. After adjusting the I Submenu, then short press

S2 to save the adjusted results and quit H submenu, then enter normal interface.

Second correction:
Short press S2 in the normal interface, then enter " minutes : seconds" interface. Long
press S2, make the second zero.Then short press S2 twice enter normal interface.

5. Schematic

3
 www.icstation.com

Note: When installing PR1 exclusion, please pay attention to

its direction. The side of the word is facing the MCU.

Users can complete the installation by PCB silk screen and component

listing. Please do not have pseudo welding.

4
 www.icstation.com

6. Component listing
NO. Component Name PCB Marker Parameter QTY
1 Metal Film Resistor R1, R2 10K 2
2 Ceramic Capacitor C2,C3 30pf 2
3 Ceramic Capacitor C4 0.1uf 104 1
4 Electrolytic Capacitor C1 10uF/25V 1
5 Network Resistor PR1 1K 1
6 Crystal Oscillator Y1 12MHz 1
7 S8550 Q1 TO-92 1
8 Button S1,S2 6*6*5mm 2
9 STC11F02E U1 DIP-20 1
10 IC Socket U1 DIP-20 1
11 Active Buzzer LS1 5V 1
12 Digital Tube DS1 4Bit Red 1
13 DC Socket J1 3.5mm 1
14 Power Cable USB to 3.5mm 1

7. Installation Steps
Step 1: Install 2pcs resistor, 3pcs ceramic capacitor, 1pcs crystal oscillator

5
 www.icstation.com

Step 2: Install 1pcs network resistor. Please pay attention to the installation direction.

Step 3: Install IC socket. Please pay attention to the installation direction.

6
 www.icstation.com

Step 4: Install 2pcs button & 1pcs S8850. Care the installation direction.

Step 5: Install 1pcs Power socket; 1pcs Electrolytic Capacitor; 1pcs

Buzzer.

7
 www.icstation.com

Step 6: Install 4Bit Digital Tube and IC. And then test!

8. Effect demonstration, Thanks for reading!

8
www.icstation.com