Scribd
Upload
52 views

C.1. Regangan Aksial Rayapan Tekan Batupasir R-1

The document describes the results of an axial compression test on two sandstone samples labeled R-1 and R-2. It includes tables showing how the axial deformation and strain of each sample increased over time as they were subjected to an axial stress of 1.162 MPa and 2.392 MPa, respectively. The test was run for over 100,000 minutes on each sample, with measurements recorded periodically to chart the increase in deformation and strain under the constant load.

Uploaded by

Agustina Elfira Ridha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
52 views

C.1. Regangan Aksial Rayapan Tekan Batupasir R-1

The document describes the results of an axial compression test on two sandstone samples labeled R-1 and R-2. It includes tables showing how the axial deformation and strain of each sample increased over time as they were subjected to an axial stress of 1.162 MPa and 2.392 MPa, respectively. The test was run for over 100,000 minutes on each sample, with measurements recorded periodically to chart the increase in deformation and strain under the constant load.

Uploaded by

Agustina Elfira Ridha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 8

LAMPIRAN C

REGANGAN AKSIAL RAYAPAN TEKAN

C.1. Regangan Aksial Rayapan Tekan Batupasir R-1


Kode Sampel : R-1
Tinggi Sampel (L) : 9,3 cm
Diameter Sampel (D) : 4,44 cm
Luas Permukaan : 15,49 cm2
Perbandingan (L/D) : 2,09
Tegangan Aksial : 1,162 MPa

Tabel C.1.
Hasil Pengujian Rayapan Tekan Batupasir R-1
Waktu Deformasi Aksial Regangan Aksial
No
(menit) (x 0,001 mm) (%)
1 0,250 10,000 0,011
2 0,500 11,000 0,012
3 1,000 12,000 0,013
4 1,250 16,000 0,017
5 1,500 16,000 0,017
6 2,000 20,000 0,021
7 3,000 22,000 0,023
8 4,000 26,000 0,027
9 5,000 31,000 0,033
10 6,000 35,000 0,037
11 7,000 42,000 0,044
12 8,000 45,000 0,047
13 9,000 46,000 0,048
14 10,000 47,000 0,049
15 11,000 48,000 0,051
16 12,000 49,000 0,052
17 13,000 50,000 0,053
18 14,000 50,000 0,053
Lanjutan Tabel C.1.
Waktu Deformasi Aksial Regangan Aksial
No
(menit) (x 0,001 mm) (%)
19 15,000 50,000 0,053

103
20 16,000 51,000 0,054
21 17,000 52,000 0,055
22 18,000 53,000 0,056
23 19,000 53,000 0,056
24 20,000 54,000 0,057
25 22,000 55,000 0,058
26 24,000 56,000 0,059
27 26,000 60,000 0,063
28 28,000 62,000 0,065
29 30,000 64,000 0,067
30 32,000 66,000 0,069
31 34,000 68,000 0,072
32 36,000 70,000 0,074
33 38,000 72,000 0,076
34 40,000 72,000 0,076
35 42,000 72,000 0,076
36 44,000 73,000 0,077
37 46,000 74,000 0,078
38 48,000 74,000 0,078
39 50,000 76,000 0,080
40 52,000 78,000 0,082
41 54,000 80,000 0,084
42 56,000 81,000 0,085
43 58,000 82,000 0,086
44 60,000 83,000 0,087
45 65,000 83,000 0,087
46 70,000 84,000 0,088
47 75,000 84,000 0,088
48 80,000 85,000 0,089
49 85,000 85,000 0,089
50 90,000 86,000 0,091
51 100,000 87,000 0,092
52 130,000 87,000 0,092
53 160,000 87,000 0,092
54 190,000 87,000 0,092
55 220,000 87,000 0,092
56 250,000 87,000 0,092
Lanjutan Tabel C.1.
Waktu Deformasi Aksial Regangan Aksial
No
(menit) (x 0,001 mm) (%)
57 270,000 87,000 0,092
58 300,000 87,000 0,092

104
59 330,000 87,000 0,092
60 360,000 87,000 0,092
61 390,000 87,000 0,092
62 420,000 87,000 0,092
63 450,000 87,000 0,092
64 480,000 87,000 0,092
65 510,000 87,000 0,092
66 540,000 87,000 0,092
67 580,000 87,000 0,092
68 640,000 87,000 0,092
69 700,000 87,000 0,092
70 760,000 87,000 0,092
71 820,000 87,000 0,092
72 880,000 87,000 0,092
73 940,000 87,000 0,092
74 1000,000 87,000 0,092
75 1060,000 87,000 0,092
76 1120,000 87,000 0,092
77 1240,000 87,000 0,092
78 1360,000 87,000 0,092
79 1480,000 87,000 0,092
80 1600,000 87,000 0,092
81 1720,000 87,000 0,092
82 1900,000 87,000 0,092
83 2080,000 87,000 0,092
84 2260,000 87,000 0,092
85 2440,000 87,000 0,092
86 2620,000 87,000 0,092
87 2800,000 93,000 0,098
88 2980,000 95,000 0,100
89 3160,000 106,000 0,112
90 3340,000 106,000 0,112
91 3520,000 113,000 0,119
92 3700,000 120,000 0,126
93 3880,000 126,000 0,133
94 4060,000 128,000 0,135
Lanjutan Tabel C.1.
Waktu Deformasi Aksial Regangan Aksial
No
(menit) (x 0,001 mm) (%)
95 4240,000 135,000 0,142
96 4420,000 146,000 0,154
97 4480,000 150,000 0,158

105
98 4620,000 153,000 0,161
99 4740,000 156,000 0,164
100 4860,000 164,000 0,173

C.2. Regangan Aksial Rayapan Tekan Batupasir R-2


Kode Sampel : R-2
Tinggi Sampel (L) : 9,2 cm
Diameter Sampel (D) : 4,46 cm
Luas Permukaan : 15,63 cm2
Perbandingan (L/D) : 2,06
Tegangan Aksial : 2,392 MPa

Tabel C.2.
Hasil Pengujian Rayapan Tekan Batupasir R-2
Deformasi
Waktu
No Aksial Regangan Aksial
(menit) (x 0,001 mm) (%)
1 0,250 10,000 0,011
2 0,500 10,500 0,011
3 1,000 11,000 0,012
4 1,250 11,000 0,012
5 1,500 12,000 0,013
6 2,000 13,000 0,014
7 3,000 13,500 0,015
8 4,000 13,500 0,015
9 5,000 13,500 0,015
10 6,000 14,000 0,015
11 7,000 14,500 0,016
12 8,000 14,500 0,016
13 9,000 15,000 0,016
14 10,000 15,000 0,016
15 11,000 16,000 0,017
16 12,000 15,000 0,016
17 13,000 15,000 0,016
Lanjutan Tabel C.2.
Deformasi
Waktu
No Aksial Regangan Aksial
(menit) (x 0,001 mm) (%)
18 14,000 15,500 0,017
19 15,000 16,000 0,017
20 16,000 16,000 0,017

106
21 17,000 17,000 0,018
22 18,000 18,000 0,020
23 19,000 18,000 0,020
24 20,000 18,000 0,020
25 22,000 18,000 0,020
26 24,000 18,000 0,020
27 26,000 20,000 0,022
28 28,000 20,000 0,022
29 30,000 20,000 0,022
30 32,000 20,000 0,022
31 34,000 20,000 0,022
32 36,000 20,000 0,022
33 38,000 20,000 0,022
34 40,000 20,000 0,022
35 45,000 20,000 0,022
36 50,000 19,000 0,021
37 55,000 20,000 0,022
38 60,000 21,000 0,023
39 65,000 22,000 0,024
40 70,000 22,000 0,024
41 75,000 23,000 0,025
42 80,000 23,000 0,025
43 90,000 23,000 0,025
44 100,000 22,500 0,024
45 110,000 22,000 0,024
46 120,000 22,000 0,024
47 130,000 22,000 0,024
48 140,000 22,000 0,024
49 150,000 22,000 0,024
50 160,000 22,500 0,024
51 170,000 27,000 0,029
52 200,000 29,000 0,032
53 230,000 30,000 0,033
54 260,000 30,000 0,033
Lanjutan Tabel C.2.
Deformasi
Waktu
No Aksial Regangan Aksial
(menit) (x 0,001 mm) (%)
55 290,000 32,000 0,035
56 320,000 32,000 0,035
57 350,000 32,000 0,035
58 380,000 32,000 0,035

107
59 410,000 32,000 0,035
60 440,000 33,000 0,036
61 470,000 33,000 0,036
62 530,000 33,000 0,036
63 590,000 34,000 0,037
64 650,000 34,000 0,037
65 710,000 35,000 0,038
66 770,000 36,000 0,039
67 830,000 36,000 0,039
68 890,000 38,000 0,041
69 950,000 38,000 0,041
70 1010,000 39,000 0,042
71 1070,000 39,000 0,042
72 1130,000 40,000 0,043
73 1190,000 43,000 0,047
74 1250,000 44,000 0,048
75 1310,000 45,000 0,049
76 1370,000 45,000 0,049
77 1430,000 45,000 0,049
78 1490,000 46,000 0,050
79 1550,000 47,000 0,051
80 1610,000 48,000 0,052
81 1670,000 49,000 0,053
82 1730,000 50,000 0,054
83 1790,000 51,000 0,055
84 1850,000 51,000 0,055
85 1910,000 51,000 0,055
86 1970,000 51,000 0,055
87 2030,000 51,000 0,055
88 2090,000 51,000 0,055
89 2150,000 51,000 0,055
90 2210,000 51,000 0,055
91 2270,000 51,000 0,055
Lanjutan Tabel C.2.
Deformasi
Waktu
No Aksial Regangan Aksial
(menit) (x 0,001 mm) (%)
92 2330,000 51,000 0,055
93 2390,000 51,000 0,055
94 2450,000 51,000 0,055
95 2510,000 51,000 0,055
96 2570,000 51,000 0,055

108
97 2630,000 51,000 0,055
98 2690,000 51,000 0,055
99 2750,000 51,000 0,055
100 2810,000 51,000 0,055
101 2870,000 51,000 0,055
102 2930,000 51,000 0,055
103 2990,000 51,000 0,055
104 3050,000 51,000 0,055
105 3110,000 51,000 0,055
106 3170,000 51,000 0,055
107 3230,000 51,000 0,055
108 3290,000 51,000 0,055
109 3350,000 51,000 0,055
110 3410,000 51,000 0,055
111 3470,000 51,000 0,055
112 3530,000 51,000 0,055
113 3590,000 51,000 0,055
114 3650,000 51,000 0,055
115 3710,000 51,000 0,055
116 3770,000 51,000 0,055
117 3830,000 51,000 0,055
118 3890,000 51,000 0,055
119 3950,000 51,000 0,055
120 4010,000 51,000 0,055
121 4070,000 51,000 0,055
122 4130,000 51,000 0,055
123 4190,000 51,000 0,055
124 4250,000 51,000 0,055
125 4310,000 51,000 0,055
126 4370,000 51,000 0,055
127 4430,000 51,000 0,055
128 4490,000 51,000 0,055
Lanjutan Tabel C.2.
Deformasi
Waktu
No Aksial Regangan Aksial
(menit) (x 0,001 mm) (%)
129 4550,000 51,000 0,055
130 4610,000 51,000 0,055
131 4670,000 51,000 0,055
132 4730,000 51,000 0,055
133 4790,000 51,000 0,055
134 4850,000 51,000 0,055

109
135 4910,000 51,000 0,055
136 4970,000 51,000 0,055
137 5030,000 51,000 0,055
138 5090,000 51,000 0,055
139 5150,000 51,000 0,055

C.3. Regangan Aksial Rayapan Tekan Batupasir R-3


Kode Sampel : R-3
Tinggi Sampel (L) : 9,3 cm
Diameter Sampel (D) : 4,42 cm
Luas Permukaan : 15,35 cm2
Perbandingan (L/D) : 2,21
Tegangan Aksial : 3,19 MPa

Tabel C.3.
Hasil Pengujian Rayapan Tekan Batupasir R-3
Lanjutan Tabel C.3.
Regangan
Waktu
No deformasi Aksial Aksial
(menit) (x 0,001 mm) (%)
Lanjutan Tabel C.3.
No Regangan
Waktu
deformasi Aksial Aksial
(menit) (x 0,001 mm) (%)
234 5295,000 376,000 0,403
Lanjutan Tabel C.3.
235 5355,000 376,000 0,403
No Waktu deformasi Aksial Regangan
236 5415,000 376,000 0,403
Aksial
237 5445,000
(menit) 379,000
(x 0,001 mm) (%)
0,406
238
Lanjutan 5475,000
Tabel C.3. 380,000 0,407
239
No 5505,000
Waktu 380,000
deformasi Aksial Regangan
0,407
240 5535,000 380,000 Aksial
0,407
241 (menit)
5565,000 (x 0,001 mm)
381,000 (%)
0,408
242 5595,000 386,000 0,413
243 5625,000 390,000 0,418
244 5655,000 393,000 0,421
245 5685,000 393,000 0,421
246 5715,000 393,000 0,421
247 5745,000 394,000 0,422
248 5775,000 394,000 0,422
249 5805,000 395,000 0,423
250 5835,000 395,000 0,423
251 5865,000 396,000 0,424
252 5895,000 397,000 0,425
253 5925,000 397,000 0,425
254 5955,000 110
397,000 0,425
255 5985,000 397,000 0,425
256 6015,000 398,000 0,426

You might also like