CS311: DATA COMMUNICATION

Multiplexing

by
Dr. Manas Khatua
Assistant Professor
Dept. of CSE
IIT Jodhpur
E-mail: [email protected]
Web: http://home.iitj.ac.in/~manaskhatua
http://manaskhatua.github.io/
Outline of the Lecture
• What is Multiplexing and why is it used ?
• Basic concepts of Multiplexing
• Types of Multiplexing:
 Frequency Division Multiplexing (FDM)
 Wavelength Division Multiplexing (WDM)
 Time Division Multiplexing (TDM)
 Synchronous
 Asynchronous
 Inverse TDM

24-09-2017 Dr. Manas Khatua 2

 Introduction
• To make efficient use of high-speed telecommunications lines,
some form of multiplexing is used.

• Multiplexing allows several transmission sources to share a

larger transmission capacity.

• Most individual data communicating devices typically require

modest data rate, but the media usually has much higher
bandwidth.

• Two communicating stations do not utilize the full capacity of

a data link.

• The higher the data rate, the most cost effective is the
transmission facility.

24-09-2017 Dr. Manas Khatua 3

 Cont…
• When the bandwidth of a medium is greater than individual
signals to be transmitted through the channel, a medium can
be shared by more than one channel of signals by using
Multiplexing.

• For efficiency, the channel capacity can be shared among a

number of communicating stations.

• Most common use of multiplexing is in long-haul

communication using coaxial cable, microwave and optical
fibre.

24-09-2017 Dr. Manas Khatua 4

Basic Concept
• A device known as Multiplexer (MUX) combines ‘n’
channels for transmission through a single medium or link.

• At the other end a De-multiplexer (DEMUX) is used to

separate out the ‘n’ channels.

24-09-2017 Dr. Manas Khatua 5

Cont…
 FDM
• FDM can be used with analog signals.

• A number of signals are carried simultaneously on the same

medium by allocating to each signal a different frequency
band.

• FDM is possible when the useful bandwidth of the

transmission medium exceeds the required bandwidth of
signals to be transmitted.

• A number of signals can be carried simultaneously if each

signal is modulated onto a different carrier frequency and the
carrier frequencies are sufficiently separated that the
bandwidths of the signals do not significantly overlap.
24-09-2017 Dr. Manas Khatua 8
Cont…

FDM Multiplexing Process

24-09-2017 Dr. Manas Khatua 9
Cont…

FDM De-Multiplexing Process

24-09-2017 Dr. Manas Khatua 9
Example

24-09-2017 Dr. Manas Khatua 10

 Guard Band

• A Guard-Band is a narrow frequency range that separates two ranges of

wider frequency.

• This ensures that simultaneously used communication channels do not

experience interference or cross-talk, which would result in decreased
quality for both transmissions.

24-09-2017 Dr. Manas Khatua 11

Applications of FDM
• Transmission of AM/FM Radio broadcasting

• TV broadcasting

• Cable television

24-09-2017 Dr. Manas Khatua 12

Wavelength Division Multiplexing
• Optical fiber medium provides enormous bandwidth.

• WDM is the most viable technology that overcomes

the huge opto-electronic bandwidth mismatch.

• WDM optical fiber network comprises optical

wavelength switches/routers interconnected by point-
to-point fiber links.

• End users may communicate with each other through

all-optical (WDM) channels known as Light-paths,
which may span over more than one fiber links.
24-09-2017 Dr. Manas Khatua 13
WDM

Example

24-09-2017 Dr. Manas Khatua 14

Time Division Multiplexing
• Possible when the bandwidth of the medium
exceeds the data rate of digital signals to be
transmitted.

• Multiple digital signals can be carried on a single

transmission path by interleaving portions of
each signal in time.

• Interleaving can be at the bit level or in blocks of

bytes.

24-09-2017 Dr. Manas Khatua 15

 TDM
 The incoming data from each source are briefly
buffered.

• Each buffer is typically one bit or one character in

length.

• The buffers are scanned sequentially to form a

composite data stream.

• The scan operation is sufficiently rapid so that each

buffer is emptied before more data can arrive.

24-09-2017 Dr. Manas Khatua 16

Synchronous TDM
• Composite data rate must be at least equal to the sum
of the individual data rate.

• The composite signal can be transmitted directly or

through a modem.

24-09-2017 Dr. Manas Khatua 17

Cont…
Frame Synchronization
• In this scheme, typically, one control bit is added to each TDM
frame.
• An identifiable pattern of bits, from frame to frame, is used as a
“control channel.”

• Thus, to synchronize, a receiver compares the incoming bits of

one frame position to the expected pattern.
• If the pattern does not match, successive bit positions are
searched until the pattern persists over multiple frames.

• Once frame synchronization is established, the receiver

continues to monitor the framing bit channel.
• If the pattern breaks down, the receiver must again enter a
framing search mode.

24-09-2017 Dr. Manas Khatua 18

Cont…
Pulse Stuffing
• If each source has a separate clock, any variation among clocks
could cause loss of synchronization.

• With pulse stuffing, the outgoing data rate of the multiplexer,

excluding framing bits, is higher than the sum of the maximum
instantaneous incoming rates.

• The extra capacity is used by stuffing extra dummy bits or

pulses into each incoming signal until its rate is raised to that
of a locally generated clock signal.
• The stuffed pulses are inserted at fixed locations in the
multiplexer frame format so that they may be identified and
removed at the de-multiplexer.
24-09-2017 Dr. Manas Khatua 19
Limitations of Synchronous TDM
• In synchronous TDM, many of the time slots in a
frame may be wasted.

• The problem is overcame in Statistical /

Asynchronous / Intelligent TDM.

• In Statistical TDM, time slots are allocated

dynamically on demand.

• It takes the advantage of the fact that not all the

attached devices may be transmitting all of the
time.
24-09-2017 Dr. Manas Khatua 20
Asynchronous TDM
• As with a synchronous TDM, the statistical multiplexer has a
number of I/O lines on one side and a higher-speed
multiplexed line on the other. Each I/O line has a buffer
associated with it.

• In the case of the statistical multiplexer, there are ‘n’ I/O

lines, but only k, where k< n, time slots available on the TDM
frame.

• For input, the function of the multiplexer is to scan the input

buffers, collecting data until a frame is filled, and then send
the frame.

• On output, the multiplexer receives a frame and distributes

the slots of data to the appropriate output buffers.
24-09-2017 Dr. Manas Khatua 21
Synchronous vs Asynchronous

24-09-2017 Dr. Manas Khatua 22

 Asynchronous TDM
• Since data arrive from and are distributed to I/O lines
unpredictably, address information is required to assure
proper delivery.

• This leads to more overhead per slot.

• Relative addressing can be used to reduce overhead.

24-09-2017 Dr. Manas Khatua 23

Performance of Asynchronous TDM
• In ATM, the data rate at the output is less than the data
rate at the input.
• However, in peak periods the input may exceed
capacity.

• Buffers of suitable size may be included to overcome

this problem.

• Let ‘n’ = number of inputs, ‘r’ = data rate of each

source, ‘M’ = effective capacity of the output, ‘α’=mean
fraction of time each input is transmitting, 0 < α < 1.

• Then, a measure of compression is C = M/(nr),

bounded by α < C < 1.

24-09-2017 Dr. Manas Khatua 24

Inverse Multiplexing
• An inverse multiplexer (IMUX) is a device performing the
opposite function of a multiplexer (MUX).

• Instead of allowing one or more low-speed analog or

digital input signals (or data streams) to be selected,
combined and transmitted at a higher speed on a single
shared medium i.e. multiplexing, an inverse multiplexer
breaks the combined and related higher speed analog or
digital signals into several concurrent lower-speed related
signals or data streams.

• Thus, using multiple slower lines, the data stream can be

more evenly distributed across all lines.

24-09-2017 Dr. Manas Khatua 25

Cont…
• The difference between de-multiplexing
(DEMUX) and inverse multiplexing is that the
output streams of de-multiplexing are
unrelated but the output streams of inverse
multiplexing are related.

• Just as multiplexers are combined with de-

multiplexers to create bi-directional data flow,
inverse multiplexers may be combined with an
inverse DEMUX (i.e. the reverse of an inverse
multiplexer).

24-09-2017 Dr. Manas Khatua 26

 Figure and slide materials are taken from the following sources:

1. W. Stallings, (2010), Data and Computer Communications

2. NPTL lecture on Data Communication, by Prof. A. K. Pal, IIT Kharagpur
3. B. A. Forouzan, (2013), Data Communication and Networking

24-09-2017 Dr. Manas Khatua 27