Scribd
Upload
15 views

Part43 - AppendixF

This document outlines the tests and inspections required for ATC transponders as specified in regulations. It details procedures for checking transponder response frequency, suppression settings, receiver sensitivity, power output, Mode S functionality, and record keeping requirements. Tests include verifying frequencies, power levels, address response, squitter transmission, and isolating dual diversity antennas on Mode S transponders.

Uploaded by

tomay777
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
15 views

Part43 - AppendixF

This document outlines the tests and inspections required for ATC transponders as specified in regulations. It details procedures for checking transponder response frequency, suppression settings, receiver sensitivity, power output, Mode S functionality, and record keeping requirements. Tests include verifying frequencies, power levels, address response, squitter transmission, and isolating dual diversity antennas on Mode S transponders.

Uploaded by

tomay777
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Appendix F to Part 43 -- ATC Transponder Tests and Inspections

The ATC transponder tests required by §91.413 of this chapter may be conducted using a
bench check or portable test equipment and must meet the requirements prescribed in
paragraphs (a) through (j) of this appendix. If portable test equipment with appropriate
coupling to the aircraft antenna system is used, operate the test equipment for ATCRBS
transponders at a nominal rate of 235 interrogations per second to avoid possible ATCRBS
interference. Operate the test equipment at a nominal rate of 50 Mode S interrogations per
second for Mode S. An additional 3 dB loss is allowed to compensate for antenna coupling
errors during receiver sensitivity measurements conducted in accordance with paragraph
(c)(1) when using portable test equipment.

(a) Radio Reply Frequency:


(1) For all classes of ATCRBS transponders, interrogate the transponder and
verify that the reply frequency is 1090±3 Megahertz (MHz).
(2) For classes 1B, 2B, and 3B Mode S transponders, interrogate the
transponder and verify that the reply frequency is 1090±3 MHz.
(3) For classes 1B, 2B, and 3B Mode S transponders that incorporate the
optional 1090±1 MHz reply frequency, interrogate the transponder and
verify that the reply frequency is correct.
(4) For classes 1A, 2A, 3A, and 4 Mode S transponders, interrogate the
transponder and verify that the reply frequency is 1090±1 MHz.
(b) Suppression: When Classes 1B and 2B ATCRBS Transponders, or Classes 1B, 2B,
and 3B Mode S transponders are interrogated Mode 3/A at an interrogation rate
between 230 and 1,000 interrogations per second; or when Classes 1A and 2A
ATCRBS Transponders, or Classes 1B, 2A, 3A, and 4 Mode S transponders are
interrogated at a rate between 230 and 1,200 Mode 3/A interrogations per second:
(1) Verify that the transponder does not respond to more than 1 percent of
ATCRBS interrogations when the amplitude of P2 pulse is equal to the P1
pulse.
(2) Verify that the transponder replies to at least 90 percent of ATCRBS
interrogations when the amplitude of the P2 pulse is 9 dB less than the P1
pulse. If the test is conducted with a radiated test signal, the interrogation
rate shall be 235±5 interrogations per second unless a higher rate has
been approved for the test equipment used at that location.
(c) Receiver Sensitivity:

Page 1 of 3
(1) Verify that for any class of ATCRBS Transponder, the receiver minimum
triggering level (MTL) of the system is −73±4 dbm, or that for any class of
Mode S transponder the receiver MTL for Mode S format (P6 type)
interrogations is −74±3 dbm by use of a test set either:

(i) Connected to the antenna end of the transmission line;


(ii) Connected to the antenna terminal of the transponder with a
correction for transmission line loss; or
(iii) Utilized radiated signal.

(2) Verify that the difference in Mode 3/A and Mode C receiver sensitivity does
not exceed 1 db for either any class of ATCRBS transponder or any class of
Mode S transponder.
(d) Radio Frequency (RF) Peak Output Power:
(1) Verify that the transponder RF output power is within specifications for the
class of transponder. Use the same conditions as described in (c)(1)(i), (ii),
and (iii) above.

(i) For Class 1A and 2A ATCRBS transponders, verify that the


minimum RF peak output power is at least 21.0 dbw (125 watts).
(ii) For Class 1B and 2B ATCRBS Transponders, verify that the
minimum RF peak output power is at least 18.5 dbw (70 watts).
(iii) For Class 1A, 2A, 3A, and 4 and those Class 1B, 2B, and 3B Mode
S transponders that include the optional high RF peak output
power, verify that the minimum RF peak output power is at least
21.0 dbw (125 watts).
(iv) For Classes 1B, 2B, and 3B Mode S transponders, verify that the
minimum RF peak output power is at least 18.5 dbw (70 watts).
(v) For any class of ATCRBS or any class of Mode S transponders,
verify that the maximum RF peak output power does not exceed
27.0 dbw (500 watts).

(e) Mode S Diversity Transmission Channel Isolation: For any class of Mode S
transponder that incorporates diversity operation, verify that the RF peak output
power transmitted from the selected antenna exceeds the power transmitted from
the nonselected antenna by at least 20 db.
(f) Mode S Address: Interrogate the Mode S transponder and verify that it replies only
to its assigned address. Use the correct address and at least two incorrect

Page 2 of 3
addresses. The interrogations should be made at a nominal rate of 50
interrogations per second.
(g) Mode S Formats: Interrogate the Mode S transponder with uplink formats (UF) for
which it is equipped and verify that the replies are made in the correct format. Use
the surveillance formats UF=4 and 5. Verify that the altitude reported in the replies
to UF=4 are the same as that reported in a valid ATCRBS Mode C reply. Verify that
the identity reported in the replies to UF=5 are the same as that reported in a valid
ATCRBS Mode 3/A reply. If the transponder is so equipped, use the communication
formats UF=20, 21, and 24.
(h) Mode S All-Call Interrogations: Interrogate the Mode S transponder with the Mode
S-only all-call format UF=11, and the ATCRBS/Mode S all-call formats (1.6
microsecond P4 pulse) and verify that the correct address and capability are
reported in the replies (downlink format DF=11).
(i) ATCRBS-Only All-Call Interrogation: Interrogate the Mode S transponder with the
ATCRBS-only all-call interrogation (0.8 microsecond P4 pulse) and verify that no
reply is generated.
(j) Squitter: Verify that the Mode S transponder generates a correct squitter
approximately once per second.
(k) Records: Comply with the provisions of §43.9 of this chapter as to content, form,
and disposition of the records.

Note: The tests in (e) through (j) apply only to Mode S transponders.

[Amdt. 43-26, 52 FR 3390, Feb. 3, 1987; 52 FR 6651, Mar. 4, 1987, as amended by Amdt. 43-31, 54 FR 34330, Aug. 18,
1989]

Page 3 of 3

You might also like