International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 810

ISSN 2229-5518

Comparative Study of Steel Structures Design

Using IS 800:1984 & IS 800:2007
Prof. S.S.Patil, L.A.Pasnur

Abstract— The latest version of the Code of Practice for general construction in steel IS 800:2007 is based on Limit State Method of design. The
design concept is totally changed in comparison to earlier IS 800:1984 which is based on elastic method. The design methodologies for the steel
structures namely, working stress design method and limit state design methods are briefly explained. The importance of limit state design meth
od is highlighted. In the present work, the detailed study of structural components as tension members and compression members by designing
using Limit State Method and Working Stress Method has been carried out and submitted the comparative study of the same in the form of
graphs.

Index Terms— IS 800:1984, IS 800:2007, Limit state method (Plastic method), Working stress method (Elastic method).

——————————  ——————————
1 CONCEPT OF ELASTIC METHOD

I n the elastic method of design, the worst combination of

loads is ascertained and the members are proportioned on
the basis of working stresses. These stresses should never
shall have the values given in this section according to the
material, the type of load and the limit state being considered.
The reliability of design is ensured by satisfying the require-
exceed the permissible ones as laid down by the code.The ment:
method basically assumes that the structural material behaves Design action ≤ Design strength
in linear elastic manner, and that adequate safety can be en-
sured by suitably restricting stresses in the material due to the 2.1 Partial Safety Factors:
expected working loads (service loads) on the structure. The variation due to the difference between the overall re-
Stresses caused by the ‘characteristic’ loads are checked sistances of a structure to a set of loads, predicted by the de-
against the permissible stress which is a fraction of yield sign calculations and the resistance of the actual structure is
stress. Thus the permissible stress may be defined in terms of taken care of by a set of partial safety factors or γ factors. The
factor of safety, which takes care of the overload or other un-
specific effect of variability in material and geometric proper-
known factors. Thus,
ties is taken care of by the partial safety factors for strength,
Permissible stress = Yield stress / factor of safety
γm. The variability of the loads on the structure, or more spe-
Thus, in working stress method
cifically, the load effects on the various structural components,
Working stress ≤ permissible stress
is reflected through the partial safety factors for loads (load
factors) γfk.
2 CONCEPT OF LIMIT STATE METHOD Table 1 Partial Safety Factor for Materials, γm

The object of limit state design can be paraphrased as Sr. Definition Partial safety factor
achievement of an acceptable probability that a part or whole no.
of structure will not become unfit for its intended use during 1 Resistance governed by 1.10
its life time owing to collapse, excessive deflection etc, under yielding, γmo
the actions of all loads and load effects. The acceptable limits 2 Resistance of member to 1.10
of safety and serviceability requirements before failure occurs buckling, γmo
are called as limit state. For achieving the design objectives, 3 Resistance governed by 1.25
the design shall be based on characteristic values for material ultimate stress, γm1
strengths and applied loads (actions), which take into account 4 Resistance of connection: Shop fab- Field fabri-
the probability of variations in the material strengths and in rications cations
the loads to be supported. The characteristic values shall be Bolts – Friction type, , γmf 1.25 1.25
based on statistical data, if available. Where such data is not Bolts – Bearing type, , γmb 1.25 1.25
available, these shall be based on experience. The design val- Rivets , γmr 1.25 1.25
ues are derived from the characteristic values through the use Welds , γmw 1.25 1.50
of partial safety factors, both for material strengths and for
loads. In the absence of special considerations, these factors

————————————————
 L.A.Pasnur is currently pursuing masters degree program in Structural
engineering in Walchand Institute of Technology, Solapur (Maharashtra), Table 2 Partial Safety Factors for Loads, γf for Limit States
India, PH-08087531287.
E-mail: [email protected]
 Prof. S.S.Patil is associate professor in Civil engineering in Walchand IJSER © 2013
http://www.ijser.org
Institute of Technology, Solapur (Maharashtra), India, PH-09422065735.
E-mail: [email protected]
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 811
ISSN 2229-5518

Combination Limit state of strength Limit state of serviceability

DL LL WL/ AL DL LL WL/E
Leading Accompanying EL Leading Accompanying L
DL+LL+CL 1.5 1.5 1.05 - - 1.0 1.0 1.0 -

DL+LL+CL 1.2 1.2 1.05 0.6 - 1.0 0.8 0.8 0.8

+WL/EL 1.2 1.2 0.53 1.2
DL+WL/EL 1.5 - - 1.5 - 1.0 - - 1.0
*
(0.9)
DL+ER 1.2 1.2 - - - - - - -
(0.9)
DL+LL+AL 1.0 0.35 0.35 - 1.0 - - - -

* This value is to be considered when stability against overturning or stress reversal is critical
Abbreviations: DL= Dead Load, LL= Imposed Load (Live Loads), WL= Wind Load, CL= Crane Load (Vertical/horizontal),
AL=Accidental Load, ER= Erection Load, EL= Earthquake Load.

4.1 Design Strength Due to Yielding of Gross Section

3 CODAL PROVISIONS FOR DESIGN OF TENSION The design strength of members under axial tension, Tdg, as
MEMBER BY WORKING STRESS METHOD ( IS governed by yielding of gross section, is given by,
800:1984) Tdg = Ag fy / γmo
3.1 Axial Stress Where,
γmo = partial safety factor for failure in tension by yielding
The permissible stress in axial tension, σat, in MPa on the net
4.2 Design Strength Due to Rupture of Critical Section
effective area of the sections shall not exceed:
σat = 0.6 fy a) Plates
3.2 Design Details The design strength in tension of a plate, Tdn, as governed by
i) In the case of single angle connected through one leg the net rupture of net cross-sectional area, An, at the holes is given by,
effective sectional area shall be taken as: Tdn = 0.9 Anfu / γm1
Al + A2k Where,
where, γm1 = partial safety factor for failure at ultimate stress
k = 3A1 / (3A1 + A2) b) Single Angles
ii) In the case of a pair of angles back-to-back ( or a single tee ), The design strength, Tdn, as governed by rupture at net section
connected by one leg of each angle ( or by the flange of the tee is given by:
) to the same side of a gusset, the net effective area shall be Tdn = 0.9 Anc fu / m1 + Ago fy/ mo
taken as, Where,
Al + A2k  = 1.4 – 0.076 (w/t) (fy/fu) (bs/Lc)
where,
k = 5A1 / (5A1 + A2) Where,
w = outstand leg width,
bs = shear lag width and
4 CODAL PROVISIONS FOR DESIGN OF TENSION Lc = length of the end connection, that is the distance
MEMBER BY LIMIT STATE METHOD ( IS 800:2007) between the outermost bolts in the end joint measured along
The factored design tension T, in the members shall the load direction or length of the weld along the
satisfy the following requirement: load direction.
T < Td
4.3 Design Strength Due to Block Shear
Where,
The block shear strength, Tdb of connection shall be taken as
Td = Design strength of the member.
smaller of
The design strength of a member under axial tension, Td, is the Tdb = [ Avg fy/(√3 mo) + 0.9 Atn fu/m1] or
lowest of the design strength due to yielding of gross section, Tdb = (0.9Avnfu / (√3 m1) + (Atg fy / mo)
Tdg; rupture strength of critical section, Tdn ; and block shear
Tdb ,given in 4.1,4. 2, & 4.3 below respectively.

IJSER © 2013
http://www.ijser.org
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 812
ISSN 2229-5518

7 COMPARATIVE STUDY

Table 3 List of Studied Parameters

1. Type of Mem-
5 CODAL PROVISIONS FOR DESIGN OF COMPRESSION Tension member
ber
MEMBER BY WORKING STRESS METHOD ( IS Sections ana-
ISA35x35x6 to ISA200x200x25
800:1984) lysed
5.1 Axial stress 2. Type of Mem-
Compression member
The direct stress in compression on the gross sectional area of ber
axially loaded compression members shall not exceed 0.6fy Sections ana-
nor the permissible stress σac, calculated using the following ISJB150 to ISHB450
lysed
formula, Length of col-
σac = 3m, 4m,5m
umn
Where,
3.
σac = permissible stress in axial compression, in MPa; End condition Both ends of column pinned
fcc = elastic critical stress in compression, =
E = modulus of elasticity of steel (2x105 MPa);
λ (= l/r ) = slenderness ratio of the member, ratio of the effec- 7.1 Comparison of Tension member by both codes
tive length to appropriate radius of gyration; Here, the load carrying capacity (L.C.C ) of tension member
n = a factor assumed as 1.4. is carried out by both IS 800-1984 & IS 800-2007 and compari-
son is shown accordingly in the form of graphs for all the
6 CODAL PROVISIONS FOR DESIGN OF COMPRESSION equal angle sections.( Fig.1 & fig.2).
MEMBER BY LIMIT STATE METHOD ( IS 800:2007)
1. The design compressive strength Pd, of a member is given
by ;
P < Pd
Where,
Pd = Ae fcd
2. The design compression stress, fcd of an axially loaded
compression member shall be calculated using following for-
mula,

fcd =
Where,
φ = 0.5[1 + α (λ – 0.2) +λ2]
λ = non dimensional effective slenderness ratio
=

fcc = euler buckling stress =

Where,
KL/r = effective slenderness ratio or ratio of effective
length, KL to appropriate radius of gyration, r
α = imperfection factor
χ = stress reduction factor for different bucking class ,
slenderness ratio and yield stress
σmo = partial factor of safety for material strength.

IJSER © 2013
http://www.ijser.org
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 813
ISSN 2229-5518

7.2 COMPARISON OF COMPRESSION MEMBER BY BOTH

CODES
Similarly, L.C.C. of compression members is carried out by
by both IS 800-1984 & IS 800-2007 for all I sections for column
pinned at both ends for column length of 2m,3m & 4m.This is
shown graphically.( Fig.3 to fig.5).

IJSER © 2013
http://www.ijser.org
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 814
ISSN 2229-5518

IJSER © 2013
http://www.ijser.org
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 815
ISSN 2229-5518

8 OBSERVATIONS
8.1 For Tension member
On comparison of the strength of sections calculated using σac - axial compressive stress
IS 800-1984 & IS 800-2007, the observation made from the σat - axial tensile stress
graphs (fig.1 & fig.2) are as under: L -Length of the end connection, i.e. distance between the
The Limit State Method (LSM) gives higher values than Work- outermost bolts in the joint along the length direction or
ing Stress Method (WSM) or Elastic method (EM). For Equal length of the weld along the length direction
angle, it varies from 12% to 50% for higher sections to smaller Lc- length of the end connection, i.e. the distance between the
outermost bolts in the end joint measured along the load di-
sections.
rection or length of the weld along the load direction
8.2 For Compression member LSM – Limit state method
t - thickness of the leg
On comparison of the strength of sections calculated using
IS 800-1984 & IS 800-2007 ( fig.3 to fig.5), it was found that w- outstand leg width
the strength increases with increase in size of the sections γmo - the partial safety factor for failure in tension by yielding
to the maximum of 15% in Elastic method. So the limit state γm1 - partial safety factor for failure at ultimate stress
gives lower values than elastic method. λ = non dimensional effective slenderness ratio
α = imperfection factor
9 CONCLUSION χ = stress reduction factor for different bucking class , slender-
9.1 For Tension member ness ratio and yield stress
The design of tension member using Angles by Limit state
method ( IS 800-2007) is economical over the working stress
method ( IS 800-1984) which values for 12% to 54%. 11 REFERANCE
[1] Design Manual for Designing Steel Structure according to
9.2 For Compression member New IS:800-2007.
1.The percentage increase in load carrying capacity as per IS [2] Dr. N. Subramanian; Design of Steel Structures‛; Oxford
800-1984 is marginally higher than IS 800-2007. The maximum University Press, New Delhi.
increase was found to be a maximum of 15%. [3] Dr. N. Subramanian, ‚Code Of Practice On Steel Structures
2. The section fails if designed by IS 800-2007. So here, the elas- -A Review Of IS 800: 2007‛, Computer Design Consultants,
tic method is economical than limit state method. Gaithersburg, MD 20878, USA.
[4] Duggal.S.K. ‘Limit State Design of Steel Structrues’Tata
10 NOTATIONS McGraw Hill EducationPrivate Limited ., New Delhi, 2010., 3
a - connecting leg rd edition.
A - section area [5] IS 800:1984 ‘Indian Standard General Construction in Steel
A1 - effective cross-sectional area of the connected leg — Code of Practice’.
A2 - the gross cross-sectional area of the unconnected leg [6] IS 800:2007 ‘Indian Standard General Construction in Steel
Ae - effective sectional area — Code of Practice’.
Ag - gross area of cross section [7] Kala.P , Vimala.S , Ilangovan.R ‘Critical appraisal on steel
Ago - gross area of outstanding leg water tank design using recent and past I. S codes’ Interna-
An - net area of the total cross section tional Journal of Civil and Structural Engineering Volume
Anc - net area of connected leg of the member 1,No.3 2010.
Atg - minimum gross in tension from the hole to the toe of [8] M. Krishnamoorthy, D.Tensing ‘Design of Compression
the angle or next last row of bolt in plates, perpendicular to Members Based on IS 800-2007 and IS 800-1984- Comparison’
the line of force Journal of Information, Knowledge and Research in Civil En-
Atn - net area in tension from the hole to the toe of the angle gineering, Volume 2, Issue1.
or next last row of bolt in plates, perpendicular to the line
of force
Avg - minimum gross area in shear along a line of transmit-
ted force
Avn - net area in shear along a line of transmitted force
bs -shear lag width
E - modulus of elasticity
EM – elastic method
fcc - critical buckling stress
fcd - design compression stress
fu - characteristic ultimate stress
fy - characteristic yield strength
IJSER © 2013
http://www.ijser.org
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 816
ISSN 2229-5518

IJSER © 2013
http://www.ijser.org
International Journal of Scientific & Engineering Research, Volume 4, Issue 4, April-2013 817
ISSN 2229-5518

IJSER © 2013
http://www.ijser.org