BEAM DESIGN CALCULATION

Group :G1
Beam No :B1
Analysis Reference (Member) 7m :52
Beam Length :3599.99 mm
Breadth (B) :200 mm
Depth (D) :300 mm
Effective Depth (d) :250 mm
Design Code :ACI 318M - 2011
Beam Type :Ductile Beam (Special Frame)
Grade Of Concrete (Fck) :C21 N/sqmm
Grade Of Steel :Fy230 N/sqmm
Clear Cover (Cmin) :40 mm
Es :2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top

Left Mid Right Left Mid Right

Critical L/C - Analysis 23 19 25 21 23 19

Critical L/C - RCDC 19 15 21 17 19 15

Mu (kNm) 3.076 5.292 2.76 13.454 2.9 13.547

As (flex) (sqmm) (C) 59.9 103.64 53.67 269.34 56.44 271.26
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -

Al (Dist) (sqmm) (D) - - - - - -

Ast (sqmm) 201.06 134.73 201.06 304.35 73.38 304.35

AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12

Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
Compression reinforcement required for
A = Asc (flex) =
bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement
C = As (flex) =
calculated at a given section
Distributed longitudinal torsional
D = Al (Dist) =
reinforcement at section considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right

Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.452 0.804
Vu (kN) 10.7 7.28 9.54
Mu-Sect (kNm) - 1.32 -

Vc (kN) 32.62 30.38 32.62

Vs (kN) - - -

D+L
V (kN) 3.93 3.68
Mh (kNm) 27.03 27.03

Ms (kNm) 15.67 15.67

Sway-Right (kN) 7.93 15.54
Sway-Left (kN) 15.79 8.18
Vu-Sway (kN) 15.79 15.54
Vud (kN) 15.79 15.54
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0

Ao= Φ*Aoh - - -

At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100

Av Total Prv (sqmm) 1570.8 1256.64 1570.8

 Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

=
Spc3 = 6 x Small Longitudinal Dia 72 mm
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <=
1000

Group : G1
Beam No : B2
Analysis Reference (Member) 7m : 53
Beam Length : 2600 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

 Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 23 19 25 21 15 19
Critical L/C - RCDC 19 15 21 17 11 15
Mu (kNm) 7.47 5.083 7.21 11.504 4.646 12.522
As (flex) (sqmm) (C) 147.14 99.49 142 229.07 90.83 250.02
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 201.06 129.33 201.06 297.79 118.08 304.35
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.804
Vu (kN) 6.27 4.47 5.98
Mu-Sect (kNm) - 0.1 -
Vc (kN) 32.62 32.62 32.62
Vs (kN) - - -
D+L
V (kN) 2.61 2.43
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 13.81 18.85
Sway-Left (kN) 19.03 13.99
Vu-Sway (kN) 19.03 18.85
Vud (kN) 19.03 18.85
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G1
Beam No : B3
Analysis Reference (Member) 7m : 54
Beam Length : 800 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Cantilever Beam
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis - 22 22 22 22 -
Critical L/C - RCDC - 18 18 18 18 -
Mu (kNm) - 0.149 0.19 0.444 0.167 -
As (flex) (sqmm) (C) - 2.89 3.66 8.6 3.23 -
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -

Ast (sqmm) 65 65 65 65 65 65
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.452
Vu (kN) 1.58 1.06 0.53
Mu-Sect (kNm) - 0.09 -
Vc (kN) 32.62 32.62 30.38
Vs (kN) - - -
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 125 125 125
SPrv (mm) 125 125 125
Av Total Prv (sqmm) 1256.64 1256.64 1256.64

Skin reinforcement
Beam Width = 200 mm
Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G2
Beam No : B4
Analysis Reference (Member) 7m : 55
Beam Length : 3599.99 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 23 19 25 21 23 19
Critical L/C - RCDC 19 15 21 17 19 15
Mu (kNm) 0.919 8.416 0.72 18.896 2.922 18.715
As (flex) (sqmm) (C) 17.81 166.19 13.99 384.16 56.88 380.27
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 201.06 216.05 201.06 384.16 73.95 380.26
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.452 0.804
Vu (kN) 17.98 12.92 15.37
Mu-Sect (kNm) - 2.21 -
Vc (kN) 32.62 30.38 32.62
Vs (kN) - - -
D+L
V (kN) 5.32 4.81
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 6.54 16.67
Sway-Left (kN) 17.18 7.05
Vu-Sway (kN) 17.18 16.67
Vud (kN) 17.98 16.67
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm
 For Ductility (Special Frames)
Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G2
Beam No : B5
Analysis Reference (Member) 7m : 56
Beam Length : 2600 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 23 19 25 21 15 19
Critical L/C - RCDC 19 15 21 17 11 15
Mu (kNm) 6.875 5.625 6.9 14.226 4.777 14.708
As (flex) (sqmm) (C) 135.21 110.27 135.76 285.39 93.44 295.46
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -

Al, min(sqmm)(Tor.) (D) - - - - - -

Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 201.06 143.35 201.06 304.35 121.47 304.35
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.804
Vu (kN) 10.5 7.11 8.84
Mu-Sect (kNm) - 0.07 -
Vc (kN) 32.62 32.62 32.62
Vs (kN) - - -
D+L
V (kN) 3.39 3.02
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 13.04 19.44
Sway-Left (kN) 19.81 13.4
Vu-Sway (kN) 19.81 19.44
Vud (kN) 19.81 19.44
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G2
Beam No : B6
Analysis Reference (Member) 7m : 57
Beam Length : 800 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Cantilever Beam
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm
For Longitudinal Reinf
 Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis - 22 22 22 22 -
Critical L/C - RCDC - 18 18 18 18 -
Mu (kNm) - 0.149 0.19 0.444 0.167 -
As (flex) (sqmm) (C) - 2.89 3.66 8.6 3.23 -
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 65 65 65 65 65 65
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.452
Vu (kN) 1.58 1.06 0.53
Mu-Sect (kNm) - 0.09 -
Vc (kN) 32.62 32.62 30.38
Vs (kN) - - -
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2

Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 125 125 125
SPrv (mm) 125 125 125
Av Total Prv (sqmm) 1256.64 1256.64 1256.64

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G3
Beam No : B7
Analysis Reference (Member) 7m : 58
Beam Length : 3599.99 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 23 19 25 21 23 19
Critical L/C - RCDC 19 15 21 17 19 15
Mu (kNm) 3.837 5.555 3.48 14.193 3.264 14.293
As (flex) (sqmm) (C) 74.86 108.86 67.92 284.71 63.59 286.79
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 201.06 141.52 201.06 304.35 82.67 304.35
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.452 0.804
Vu (kN) 10.69 7.27 9.55
Mu-Sect (kNm) - 1.32 -
Vc (kN) 32.62 30.38 32.62
Vs (kN) - - -
D+L
V (kN) 3.93 3.68
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 7.93 15.54
Sway-Left (kN) 15.79 8.18
Vu-Sway (kN) 15.79 15.54
Vud (kN) 15.79 15.54
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G3
Beam No : B8
Analysis Reference (Member) 7m : 59
Beam Length : 2600 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 23 19 25 21 19 19
Critical L/C - RCDC 19 15 21 17 15 15
Mu (kNm) 8.502 5.599 8.24 12.499 5.168 13.585
As (flex) (sqmm) (C) 167.92 109.75 162.63 249.56 101.19 272.05
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 218.29 142.68 211.43 304.35 131.55 304.35
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.804
Vu (kN) 6.25 4.49 6
Mu-Sect (kNm) - 0.11 -
Vc (kN) 32.62 32.62 32.62
Vs (kN) - - -
D+L
V (kN) 2.61 2.43
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 13.81 18.85
Sway-Left (kN) 19.03 13.99
Vu-Sway (kN) 19.03 18.85
Vud (kN) 19.03 18.85
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000
Group : G3
Beam No : B9
Analysis Reference (Member) 7m : 60
Beam Length : 800 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Cantilever Beam
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis - 22 22 22 22 -
Critical L/C - RCDC - 18 18 18 18 -
Mu (kNm) - 0.149 0.19 0.444 0.167 -
As (flex) (sqmm) (C) - 2.89 3.66 8.6 3.23 -
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 65 65 65 65 65 65
AstPrv (sqmm) 226.2 226.2 226.2 402.12 402.12 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#16 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
D = Al (Dist) = Distributed longitudinal torsional reinforcement at section
 considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.452
Vu (kN) 1.58 1.06 0.53
Mu-Sect (kNm) - 0.09 -
Vc (kN) 32.62 32.62 30.38
Vs (kN) - - -
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 125 125 125
SPrv (mm) 125 125 125
Av Total Prv (sqmm) 1256.64 1256.64 1256.64

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G4
Beam No : B10
Analysis Reference (Member) 7m : 78
Beam Length : 4099.99 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 26 20 24 20 24 22
Critical L/C - RCDC 22 16 20 16 20 18
Mu (kNm) 3.266 6.558 1.45 16.341 2.93 16.628
As (flex) (sqmm) (C) 63.64 128.87 28.2 329.78 57.04 335.85
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 82.73 167.53 201.06 329.78 74.15 335.85
AstPrv (sqmm) 226.2 226.2 226.2 402.12 226.2 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#12 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.804
Vu (kN) 11.52 10.9 13.19
Mu-Sect (kNm) - 1.82 -
Vc (kN) 32.62 32.62 32.62
Vs (kN) - - -
D+L
V (kN) 4.45 4.54
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 14.86 5.88
Sway-Left (kN) 5.96 14.95
Vu-Sway (kN) 14.86 14.95
Vud (kN) 14.86 14.95
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G4
Beam No : B11
Analysis Reference (Member) 7m : 77
Beam Length : 4099.99 mm
Breadth (B) : 200 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 66.53 kNm
As,min (flex) (B) : 304.35 sqmm
As,nominal (Bn) : 65 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 26 20 24 20 24 22
Critical L/C - RCDC 22 16 20 16 20 18
Mu (kNm) 1.449 6.727 1.76 16.638 2.924 16.343
As (flex) (sqmm) (C) 28.09 132.25 34.14 336.06 56.92 329.82
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 201.06 171.92 201.06 336.06 74 329.82
AstPrv (sqmm) 226.2 226.2 226.2 402.12 226.2 402.12
Reinforcement 2-#12 2-#12 2-#12 2-#16 2-#12 2-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.804 0.804 0.804
Vu (kN) 11.71 10.71 12.99
Mu-Sect (kNm) - 1.56 -
Vc (kN) 32.62 32.62 32.62
Vs (kN) - - -
D+L
V (kN) 4.37 4.61
Mh (kNm) 27.03 27.03
Ms (kNm) 15.67 15.67
Sway-Right (kN) 14.79 5.8
Sway-Left (kN) 6.04 15.03
Vu-Sway (kN) 14.79 15.03
Vud (kN) 14.79 15.03
Av (sqmm) 304.35 304.35 304.35
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 304.35 304.35 304.35
Asv Reqd (sqmm) 304.348 304.348 304.348
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section
Spc3 = 6 x Small Longitudinal Dia = 72 mm
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 200 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G5
Beam No : B12
Analysis Reference (Member) 7m : 80
Beam Length : 4099.99 mm
Breadth (B) : 250 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 83.16 kNm
As,min (flex) (B) : 380.43 sqmm
As,nominal (Bn) : 81.25 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 26 20 - 20 24 22
Critical L/C - RCDC 22 16 - 16 20 18
Mu (kNm) 2.221 10.075 - 21.731 2.35 22.955
As (flex) (sqmm) (C) 43.11 198.75 - 439.88 45.63 465.95
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 81.25 258.38 301.59 439.88 81.25 465.95
AstPrv (sqmm) 226.2 339.3 339.3 603.18 339.3 603.18
Reinforcement 2-#12 3-#12 3-#12 3-#16 3-#12 3-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.965 0.965 0.965
Vu (kN) 18.11 18.31 21.53
Mu-Sect (kNm) - 3.13 -
Vc (kN) 42.06 42.06 42.06
Vs (kN) - - -
D+L
V (kN) 5.74 6.12
Mh (kNm) 39.98 39.98
Ms (kNm) 15.78 23.32
Sway-Right (kN) 19.35 7.49
Sway-Left (kN) 9.7 21.56
Vu-Sway (kN) 19.35 21.56
Vud (kN) 19.35 21.56
Av (sqmm) 380.43 380.43 380.43
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 380.43 380.43 380.43
Asv Reqd (sqmm) 380.435 380.435 380.435
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8
Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 250 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G5
Beam No : B13
Analysis Reference (Member) 7m : 79
Beam Length : 4099.99 mm
Breadth (B) : 250 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 83.16 kNm
As,min (flex) (B) : 380.43 sqmm
As,nominal (Bn) : 81.25 sqmm
For Longitudinal Reinf
Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis - 20 - 20 24 22
Critical L/C - RCDC - 16 - 16 20 18
Mu (kNm) - 10.18 - 22.49 2.517 22.294
As (flex) (sqmm) (C) - 200.87 - 456.03 48.89 451.85
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 301.59 261.13 301.59 456.02 81.25 451.85
AstPrv (sqmm) 339.3 339.3 339.3 603.18 339.3 603.18
Reinforcement 3-#12 3-#12 3-#12 3-#16 3-#12 3-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.965 0.965 0.965
Vu (kN) 18.48 17.94 21.16
Mu-Sect (kNm) - 2.69 -
Vc (kN) 42.06 42.06 42.06
Vs (kN) - - -
D+L
V (kN) 5.64 6.22
Mh (kNm) 39.98 39.98
Ms (kNm) 23.32 23.32
Sway-Right (kN) 21.08 9.22
Sway-Left (kN) 9.8 21.66
Vu-Sway (kN) 21.08 21.66
Vud (kN) 21.08 21.66
Av (sqmm) 380.43 380.43 380.43
Tu (kNm) 0 0 0

Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 380.43 380.43 380.43
Asv Reqd (sqmm) 380.435 380.435 380.435
SCalc (mm) 100 125 100

SPrv (mm) 100 125 100

Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 250 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G6
Beam No : B14
Analysis Reference (Member) 7m : 82
Beam Length : 4099.99 mm
Breadth (B) : 250 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 83.16 kNm
As,min (flex) (B) : 380.43 sqmm
As,nominal (Bn) : 81.25 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 26 22 - 20 24 22
Critical L/C - RCDC 22 18 - 16 20 18
Mu (kNm) 2.315 5.615 - 13.693 2.045 13.931
As (flex) (sqmm) (C) 44.94 109.75 - 272.25 39.67 277.11
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 81.25 142.67 301.59 353.92 81.25 360.24
AstPrv (sqmm) 226.2 226.2 339.3 603.18 339.3 603.18
Reinforcement 2-#12 2-#12 3-#12 3-#16 3-#12 3-#16

Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))
For Transverse Reinf
Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.965 0.965 0.965

Vu (kN) 10.74 10.02 12.31

Mu-Sect (kNm) - 1.62 -
Vc (kN) 42.06 42.06 42.06
Vs (kN) - - -
D+L
V (kN) 4.26 4.41
Mh (kNm) 39.98 39.98
Ms (kNm) 15.78 23.32
Sway-Right (kN) 17.87 9.2
Sway-Left (kN) 11.18 19.85
Vu-Sway (kN) 17.87 19.85
Vud (kN) 17.87 19.85
Av (sqmm) 380.43 380.43 380.43
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 380.43 380.43 380.43
Asv Reqd (sqmm) 380.435 380.435 380.435
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8

Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section

= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm
Skin reinforcement

Beam Width = 250 mm

Beam Depth = 300 mm
Depth = 300 <= 1000

Group : G6
Beam No : B15
Analysis Reference (Member) 7m : 81
Beam Length : 4099.99 mm
Breadth (B) : 250 mm
Depth (D) : 300 mm
Effective Depth (d) : 250 mm
Design Code : ACI 318M - 2011
Beam Type : Ductile Beam (Special Frame)
Grade Of Concrete (Fck) : C21 N/sqmm
Grade Of Steel : Fy230 N/sqmm
Clear Cover (Cmin) : 40 mm
Es : 2x10^5 N/sqmm
Mubal : 83.16 kNm
As,min (flex) (B) : 380.43 sqmm
As,nominal (Bn) : 81.25 sqmm

For Longitudinal Reinf

Beam Bottom Beam Top
Left Mid Right Left Mid Right
Critical L/C - Analysis 26 20 24 20 24 22
Critical L/C - RCDC 22 16 20 16 20 18
Mu (kNm) 6.946 8.194 8.17 22.428 5.978 19.856
As (flex) (sqmm) (C) 136.13 161.01 160.51 454.7 116.93 400.21
Asc (flex) (sqmm) (A) - - - - - -
Tu (kNm) - - - - - -
Tcr/4 (kNm) - - - - - -
Al, min(sqmm)(Tor.) (D) - - - - - -
Al (sqmm) (Tor.) (E) - - - - - -
Al (Dist) (sqmm) (D) - - - - - -
Ast (sqmm) 301.59 209.31 301.59 454.7 152.01 400.21
AstPrv (sqmm) 339.3 226.2 339.3 603.18 339.3 603.18
Reinforcement 3-#12 2-#12 3-#12 3-#16 3-#12 3-#16
Note: Calculation of Ast

Ast = Max {B, C+D, A+D} (for Mu > 0)

Ast = Bn (for Mu = 0)
Where,
A = Asc (flex) = Compression reinforcement required for bending moment
B = As,min (flex) = Min area of flexural reinforcement
Bn = As,nominal = Nominal area of reinforcement
Total area of longitudinal reinforcement calculated at a
C = As (flex) =
given section
Distributed longitudinal torsional reinforcement at section
D = Al (Dist) =
considered
Ast (Dist) (sqmm) = Max(Al,min (Tor), Al (Tor)) x ((2B) / (2B + 2D))

For Transverse Reinf

Left Mid Right
Critical L/C - RCDC 9 9 9
PtPrv (%) 0.965 0.965 0.965
Vu (kN) 11.48 9.89 11.57
Mu-Sect (kNm) - 2.97 -
Vc (kN) 42.06 40.78 42.06
Vs (kN) - - -
D+L
V (kN) 4.6 4.07
Mh (kNm) 39.98 39.98
Ms (kNm) 23.32 23.32
Sway-Right (kN) 20.04 11.37
Sway-Left (kN) 10.84 19.51
Vu-Sway (kN) 20.04 19.51
Vud (kN) 20.04 19.51
Av (sqmm) 380.43 380.43 380.43
Tu (kNm) 0 0 0
Ao= Φ*Aoh - - -
At (sqmm) - - -
Legs 2 2 2
Stirrup Rebar 10 10 10
Asv Torsion (sqmm) - - -
Av Total Reqd (sqmm) 380.43 380.43 380.43
Asv Reqd (sqmm) 380.435 380.435 380.435
SCalc (mm) 100 125 100
SPrv (mm) 100 125 100
Av Total Prv (sqmm) 1570.8 1256.64 1570.8
Maximum Spacing Criteria

Basic
Spc1 =d/2 = 125 mm
Spc2 = 300 mm

For Ductility (Special Frames)

Left Section, Right Section
= 72 mm
Spc3 = 6 x Small Longitudinal Dia
Spc4 = d / 4 = 62 mm
Spc5 = 150 mm
Provided Spacing = 100 mm

Mid Section
Provided Spacing = 125 mm

Skin reinforcement

Beam Width = 250 mm

Beam Depth = 300 mm
Depth = 300 <= 1000