Part - II

Tutorials
 Table of Contents
Introduction 1
1. Tutorial Problem 1: 2D Portal Frame 1-1

1.1 Methods of creating the model 1-2

1.2 Description of the Tutorial Problem 1-3
1.3 Starting the Program 1-5
1.4 Creating a New Structure 1-10
1.5 Creating the Model using the Graphical Interface 1-13
1.5.1 Generating the Model Geometry 1-16
1.5.2 Switching On Node And Beam Labels 1-23
1.5.3 Specifying Member Properties 1-26
1.5.4 Specifying Material Constants 1-32
1.5.5 Changing the Input Units of Length 1-33
1.5.6 Specifying Member Offsets 1-35
1.5.7 Printing Member Information in the Output File 1-40
1.5.8 Specifying Supports 1-43
1.5.9 Viewing the model in 3D 1-48
1.5.10 Specifying Loads 1-50
1.5.11 Specifying the Analysis Type 1-60
1.5.12 Specifying Post-Analysis Print Commands 1-62
1.5.13 Short-listing the Load Cases to be used in
Steel Design 1-66
1.5.14 Specifying Steel Design Parameters 1-68
1.5.15 Re-specifying the Analysis Command 1-74
1.5.16 Re-specifying the Track Parameter 1-75
1.5.17 Specifying the Check Code Command 1-76
1.6 Viewing the Input Command File 1-79
1.7 Creating the Model using the Command File 1-82
1.8 Performing Analysis/Design 1-91
1.9 Viewing the Output File 1-94
1.10 Post-Processing 1-102
1.10.1 Going to the Post-Processing Mode 1-103
1.10.2 Annotating the Displacements 1-106
1.10.3 Displaying Force/Moment Diagrams 1-111
1.10.4 Annotating the Force/Moment Diagram 1-114
1.10.5 Changing the Degree of Freedom for which
Forces Diagram is Plotted 1-117
1.10.6 Displaying the Dimensions of The Members 1-120
2. Tutorial Problem 2: RC Framed Structure 2-1
2.1 Methods of creating the model 2-2
2.2 Description of the Tutorial Problem 2-3
2.3 Starting the Program 2-6
2.4 Creating a New Structure 2-11
2.5 Elements of the STAAD.Pro Screen 2-14
2.6 Building the STAAD.Pro Model 2-15
2.6.1 Generating the Model Geometry 2-16
2.6.2 Changing the Input Units of Length 2-28
2.6.3 Specifying Member Properties 2-30
2.6.4 Specifying Geometric Constants 2-36
2.6.5 Specifying Material Constants 2-38
2.6.6 Specifying Supports 2-41
2.6.7 Specifying Loads 2-46
2.6.8 Specifying the Analysis Type 2-63
2.6.9 Short-listing the load cases to be used in Concrete Design 2-65
2.6.10 Specifying Concrete Design Parameters 2-67
2.6.11 Specifying Design Commands 2-71
2.7 Viewing the Input Command File 2-74
2.8 Creating the Model using the Command File 2-77
2.9 Performing the Analysis and Design 2-85
2.10 Viewing the Output File 2-88
2.11 Post-Processing 2-96
2.11.1 Going to the Post-Processing Mode 2-97
2.11.2 Viewing the Deflection Diagram 2-99
2.11.3 Switching between load cases for viewing the
deflection diagram 2-101
2.11.4 Changing the size of the deflection diagram 2-105
2.11.5 Annotating Displacements 2-108
2.11.6 Changing the units in which displacement values are
annotated 2-111
2.11.7 The Node Displacement Table 2-114
2.11.8 Displaying Force/Moment Diagrams 2-119
2.11.9 Switching between load cases for viewing the
Force/Moment diagram 2-122
2.11.10 Changing the size of the Force/Moment diagram 2-126
2.11.11 Changing the degree of freedom for which forces diagram
is plotted 2-129
2.11.12 Annotating the Force/Moment diagram 2-131
 2.11.13 Changing the units in which Force/Moment values
are annotated 2-134
2.11.14 Beam Forces Table 2-137
2.11.15 Viewing the Force/Moment diagrams from the
Beam | Graphs Page 2-141
2.11.16 Restricting the load cases for which results are viewed 2-145
2.11.17 Using Member Query 2-147
2.11.18 Producing an on-screen Report 2-152
2.11.19 Taking Pictures 2-155
2.11.20 Creating Customized Reports 2-157

3. Tutorial Problem 3: Analysis of a slab 3-1

3.1 Methods of creating the model 3-2
3.2 Description of the tutorial problem 3-3
3.3 Starting the program 3-6
3.4 Creating a new structure 3-11
3.5 Elements of the STAAD.Pro screen 3-14
3.6 Building the STAAD.Pro model 3-15
3.6.1 Generating the model geometry 3-16
3.6.2 Changing the input units of length 3-53
3.6.3 Specifying Element Properties 3-55
3.6.4 Specifying Material Constants 3-61
3.6.5 Specifying Supports 3-62
3.6.6 Specifying Primary Load Cases 3-67
3.6.7 Creating Load Combinations 3-77
3.6.8 Specifying the analysis type 3-82
3.6.9 Specifying post-analysis print commands 3-85
3.7 Viewing the input command file 3-89
3.8 Creating the model using the command file 3-91
3.9 Performing the analysis and design 3-98
3.10 Viewing the output file 3-101
3.11 Post-Processing 3-109
3.11.1 Viewing stress values in a tabular form 3-110
3.11.2 Printing the tables 3-112
3.11.3 Changing the units of values which appear in the
above tables 3-113
3.11.4 Limiting the load cases for which the results are displayed 3-115
3.11.5 Stress Contours 3-117
3.11.6 Animating stress contours 3-123
3.11.7 Creating AVI Files 3-124
 3.11.8 Viewing plate results using element query 3-127
3.11.9 Producing an onscreen report 3-131
3.11.10 Viewing Support Reactions 3-136

4. Tutorial Problem 4: Interoperability

(using STAAD.Pro and STAAD.etc) 4-1
4.1 Understanding STAAD.etc 4-2
4.2 Description of the Tutorial Problem 4-3
4.3 Using the Interactive Mode in STAAD.Pro 4-4
4.4 Designing a Footing based on results from STAAD.Pro 4-9
4.5 Designing a Base Plate based on results from STAAD.Pro 4-15
4.7 Saving the Interactive Design as a STAAD.etc File 4-16

5. Frequently Performed Tasks FPT-1

1 Selecting nodes, beams, plates, etc. FPT-1
2 Viewing the structure from different angles FPT-8
3 Switching on labels for nodes, beams, plates, etc. FPT-12
4 Displaying a portion of the model by isolating it
from the rest of the structure FPT-18
5 Creating Groups FPT-38
6 Displaying Loads on the screen FPT-47
7 Displaying Load Values on the screen FPT-52
8 Structural Tool Tip Options FPT-58
9 Identifying Beam Start and End FPT-62
10 Plotting from STAAD.Pro FPT-67
 Introduction

STAAD.Pro is a general purpose program for performing the

analysis and design of a wide variety of types of structures. The basic
three activities which are to be carried out to achieve that goal - a)
model generation b) the calculations to obtain the
analytical results c) result verification - are all facilitated by tools
contained in the program's graphical environment. This manual
contains four sample tutorials which guide the user through those 3
activities.

The first of those tutorials demonstrates these processes using a simple

two-dimensional steel portal frame. It is a good starting point for
learning the program. If you are unfamiliar with
STAAD.Pro, you will greatly benefit by going through this tutorial first.

For the second tutorial, we have chosen a reinforced concrete

frame. We generate the model, perform the analysis, and design the
concrete beams and columns. It contains extensive details on the
various facilities available for visualization and verification of results.

The modelling and analysis of a slab is demonstrated in the third

tutorial. Slabs, and other surface entities like walls are modelled
using plate elements. Large surface entities may have to be defined
using several elements and this sometimes requires a tool called a
mesh generator. This tutorial shows the simple techniques as well
as the mesh generation method for generating the finite element
model of the slab. It also explains the methods by which one can
check the results for plate elements.

A tutorial which demonstrates the inter-operability features

between STAAD.Pro and STAAD.etc. is presented in the fourth
tutorial. STAAD.etc is a set of modules which can be used to
perform component designs such as for a rectangular footing, base plate,
cantilever retaining wall, moment connection, bolt group,
etc. Users who have purchased STAAD.etc in addition to
STAAD.Pro may go through this tutorial to familiarize themselves with
the process of utilizing STAAD.etc to perform secondary
analysis and design tasks on a structure for which the primary
analysis and design is done using STAAD.Pro.
 1-1

Tutorial Problem 1: 2D Portal Frame

Section 1
This chapter provides a step-by-step tutorial for creating a 2D
portal frame using STAAD.Pro. This tutorial covers the following topics.

 Starting the Program

 Creating a New Structure
 Creating Joints and Members
 Switching On Node and Beam Labels
 Specifying Member Properties
 Specifying Material Constants
 Specifying Member Offsets
 Printing Member Information
 Specifying Supports
 Specifying Loads
 Specifying the Analysis Type
 Specifying Post-Analysis Print Commands
 Specifying Steel Design Parameters
 Performing Analysis and Design
 Viewing the Output File
 Verifying results on screen – both graphically and numerically
1-2 Tutorial 1

1.1 Methods of creating the model

There are two methods of creating the structure data:

a. using the command file

b. using the graphical model generation mode, or graphical
user interface (GUI) as it is usually referred to.

The Command File is a text file which contains the data for the
structure being modeled. This file consists of simple English-
language like commands. This command file may be created
directly using the editor built into the program, or for that matter,
any editor which saves data in text form, such as Notepad or
WordPad available in Microsoft Windows.

This command file is also automatically created behind the scenes when
the structure is generated using the Graphical User Interface.
The graphical model generation mode and the command file are
seamlessly integrated. So, at any time, you may temporarily exit
the graphical model generation mode and access the command file. You
will find that it reflects all data entered through the graphical model
generation mode. Further, when you make changes to the
command file and save it, the GUI immediately reflects the changes made
to the structure through the command file.

Both methods of creating our model are explained in this tutorial.

Section 1.3 through 1.6 explain the procedure for creating the file
using the GUI. Section 1.7 describes creation of the command file
using the STAAD.Pro text editor.
 Tutorial 1 1-3

1.2 Description of the tutorial problem

The structure for this project is a single bay, single story steel
portal frame that will be analyzed and designed. The figure below
shows the structure.

2.5 KIP/FT

Figure 1. 1

An input file called "Tut-01-portal.std" containing the input data for the
above structure has been provided with the program. This
file contains what would otherwise have resulted had we followed the
procedure explained in Section 1.7.
1-4 Tutorial 1

BASIC DATA FOR THE STRUCTURE

ATTRIBUTE DATA
Member properties Members 1 & 3 : W12X35

Member 2 : W14X34

Material Constants Modulus of Elasticity : 29000 ksi

Poisson's Ratio : 0.30

Member Offsets 6.0 inches along global X for member 2 at both ends

Supports Node 1 : Fixed

Node 4 : Pinned

Loads Load case 1 : Dead + Live

Beam 2 : 2.5 kips/ft downward along global Y

Load case 2 : Wind From Left 10

kips point force at Node 2

Load case 3 : 75 Percent of (DL+LL+WL)

Load Combination - L1 X 0.75 + L2 X 0.75

Analysis Type Linear Elastic (PERFORM)

Steel Design Consider load cases 1 and 3 only.

Parameters: Unsupported length of compression

flange for bending : 10 ft for members 2 and 3, 15 ft for
member 1.

Steel Yield Stress : 40 ksi

Perform member selection for members 2 and 3

 Tutorial 1 1-5

1.3 Starting the program

Select the STAAD.Pro icon from the STAAD.Pro 2006 program group.

Figure 1. 2
1-6 Tutorial 1

The STAAD.Pro Graphical Environment will be invoked and the

following screen comes up.

Figure 1. 3

This New dialog box will come up every time we start the program.
To turn this feature off, simply uncheck the Display this dialog box
at the Startup box at the lower left hand corner. This feature can be
turned on again at a later time when File | New is invoked from the
main menu.
 Tutorial 1 1-7
Note about the unit system :

There are two base unit systems in the program which control the
units (length, force, temperature, etc.) in which, values,
specifically results and other information presented in the tables and
reports, are displayed in. The base unit system also dictates what type
of default values the program will use when attributes
such as Modulus of Elasticity, Density, etc., are assigned based on
material types – Steel, Concrete, Aluminum – selected from the
program’s library (Please refer to Section 5 of the STAAD.Pro
Technical Reference Manual for details). These two unit systems are
English (Foot, Pound, etc.) and Metric (KN, Meter, etc.).

If you recall, one of the choices made at the time of installing

STAAD.Pro is this base unit system setting. That choice will serve
as the default until we specifically change it.

The place from where we can change this setting is under the File |
Configure menu. To get to that option, first close down the dialog
box shown in the earlier figure by clicking on Cancel. Then, click
on the File | Configure menu option (see figure below) and choose
the appropriate unit system you want. For this tutorial, let us
choose the English units (Kip, Feet, etc.).

Figure 1. 4
1-8 Tutorial 1

Figure 1. 5

Click on the Accept button to close the above dialog box.

 Tutorial 1 1-9
Following this, select File | New once again.

Figure 1. 6

The dialog box shown in Figure 1.3 will re-appear.

1-10 Tutorial 1

1.4 Creating a new structure

1. In the New dialog box, we provide some crucial initial data
necessary for building the model.

The structure type is to be defined by choosing from among Space,

Plane, Floor and Truss. A Space type is one where the structure,
the loading or both, cause the structure to deform in all 3 global
axes (X, Y and Z). In a Plane type, the geometry, loading and
deformation are restricted to the global X-Y plane only. A Floor
type is a structure whose geometry is confined to the X-Z plane. A
Truss type of structure carries loading by pure axial action. Truss
members are deemed incapable of carrying shear, bending and
torsion. For our model, let us choose Plane.

We choose Foot as the length unit and Kilo Pound as the force unit in
which we will start to build the model. The units can be changed later
if necessary, at any stage of the model creation.

We also need to provide a name in the File Name edit box. This is
the name under which the structure data will be saved on the
computer hard disk. The name “Structure?” (? will be a number) is
recommended by the program by default, but we can change it to
any name we want. Let us choose the name PORTAL.

A default path name - the location on the computer drive where the
file will be saved – is provided by the program under Location. If
you wish to save the file in a different location, type in the name,
or click the button and specify the desired path.

After specifying the above input, click on the Next button.

 Tutorial 1 1-11

Figure 1. 7

2. In the next dialog box, we choose the tools to be used to initially

construct the model. Add Beam, Add Plate or Add Solid are,
respectively, the starting points for constructing beams, plates or
solids. Open Structure Wizard provides access to a library of
structural templates which the program comes equipped with.
Those template models can be extracted and modified
parametrically to arrive at our model geometry or some of its parts.
If the model is to be created initially using the STAAD command
language, the Open STAAD Editor box can take us to the STAAD
editor. Please remember that all these options are also available
from the menus and dialog boxes of the GUI, even after we dismiss this
dialog box.

Note: If you wish to use the Editor to create the model, choose Open
STAAD Editor, click Finish, and proceed to Section 1.7.
1-12 Tutorial 1

For our model, let us check the Add Beam option. Click on the
Finish button. The dialog box will be dismissed and the
STAAD.Pro graphical environment will be displayed.

Figure 1. 8
 Tutorial 1 1-13

1.5 Creating the model using the graphical user

interface
In order to generate the model graphically, we have to familiarize
ourselves with the components of the STAAD.Pro screen. A sample
of the STAAD.Pro screen is shown in Figure 1.9.

The screen has five major elements as described below:

Menu bar
Located at the top of the screen, the Menu bar gives access to all the
facilities of STAAD.Pro.

Toolbar
The dockable Toolbar gives access to the most frequently used
commands. You may also create your own customized toolbar.

Main Window
This is the largest area at the center of the screen, where the model
drawings and results are displayed in pictorial form.

Page Control
The Page Control is a set of tabs that appear on the left-most part
of the screen. Each tab on the Page Control allows you to perform
specific tasks. The organization of the Pages, from top to bottom,
represents the logical sequence of operations, such as, definition of beams,
specification of member properties, loading, and so on.

Each tab has a name and an icon for easy identification. The name
on the tabs may or may not appear depending on your screen
resolution and the size of the STAAD.Pro window. However, the icons
on the Page Control tabs always appear.

The Pages in the Page Control area depend on the Mode of

operation. The Mode of operation may be set from the Mode menu from
the Menu bar.
1-14 Tutorial 1

Elements of the STAAD.Pro Screen

Figure 1. 9
 Tutorial 1 1-15
Data Area
The right side of the screen is called the Data Area, where
different dialog boxes, tables, list boxes, etc. appear depending on
the type of operation you are performing. For example, when you
select the Geometry | Beam Page, the Data Area contains the Node-
Coordinate table and the Member-incidence table. When you are in
the Load Page, the contents of the Data Area changes to display the
currently assigned Load cases and the icons for different types of
loads.

The icons in the toolbar as well as in the Page Control area offer
ToolTip help. As we move the mouse pointer over a button, the
name of the button – called a ToolTip – appears above or below the button.
This floating Tool tip help will identify the icon. A brief
description of the icon also appears in the status bar.

We are now ready to start building the model geometry. The steps and,
wherever possible, the corresponding STAAD.Pro commands (the
instructions which get written in the STAAD input file) are
described in the following sections.
1-16 Tutorial 1

1.5.1 Generating the model geometry

The structure geometry consists of joint numbers, their
coordinates, member numbers, the member connectivity
information, plate element numbers, etc. From the standpoint of the
STAAD command file, the commands to be generated for the
structure shown in section 1.2 are :

JOINT COORDINATES
1 0. 0. ; 2 0. 15. ; 3 20. 15. ; 4 20. 0.
MEMBER INCIDENCE
1 1 2;2 2 3;3 3 4

Steps:

1. We selected the Add Beam option earlier to facilitate adding beams

to create the structure. This initiates a grid in the main drawing
area as shown below. The directions of the global axes (X,Y,Z) are
represented in the icon in the lower left hand corner of the drawing area.

Figure 1. 10
 Tutorial 1 1-17
2. A Snap Node/Beam dialog box also appears in the data area on the
right side of the screen. The Linear tab is meant for placing the
construction lines perpendicular to one another along a "left to
right - top to bottom" pattern, as in the lines of a chess board. The
Radial tab enables construction lines to appear in a spider-web
style, which makes it is easy to create circular type models where
members are modelled as piece-wise linear straight line segments.
The Irregular tab can be used to create gridlines with unequal
spacing that lie on the global planes or on an inclined plane. We
will use the Linear tab.

In our structure, the segment consisting of members 1 to 3, and nodes

1 to 4, happens to lie in the X-Y plane. So, in this dialog box, let us
keep X-Y as the Plane of the grid. The size of the
model that can be drawn at any time is controlled by the number of
Construction Lines to the left and right of the origin of axes, and the
Spacing between adjacent construction lines. By setting 20 as
the number of lines to the right of the origin along X, 15 above the
origin along Y, and a spacing of 1 feet between lines along both X
and Y (see next figure) we can draw a frame 20ft X 15ft, adequate
for our structure. Please note that these settings are only a starting
grid setting, to enable us to start drawing the structure, and they do not
restrict our overall model to those limits.
1-18 Tutorial 1

Figure 1. 11
 Tutorial 1 1-19
3. To start creating the nodes, let us first activate the Snap
Node/Beam button by clicking on it. Then, with the help of the
mouse, click at the origin (0, 0) to create the first node.

Figure 1. 12

4. In a similar fashion, click on the following points to create nodes

and automatically join successive nodes by beam members.

(0, 15), (20, 15), and (20, 0)

The exact location of the mouse arrow can be monitored on the

status bar located at the bottom of the window where the X, Y, and
Z coordinates of the current cursor position are continuously
updated.
1-20 Tutorial 1

When steps 1 to 4 are completed, the structure will be displayed in the

drawing area as shown below.

Figure 1. 13
 Tutorial 1 1-21
5. At this point, let us remove the grid from the structure. To do that,
click on the Close button in the Snap Node/Beam dialog box.

Figure 1. 14
1-22 Tutorial 1

The grid will now be removed and the structure in the main
window should resemble the figure shown below.

Figure 1. 15

It is very important that we save our work often, to avoid loss of data
and protect our investment of time and effort against power
interruptions, system problems, or other unforeseen events. To save the file,
pull down the File menu and select the Save command.
 Tutorial 1 1-23

1.5.2 Switching on node and beam labels

1. Node and beam labels are a way of identifying the entities we have
drawn on the screen. In order to display the node and beam
numbers, right click anywhere in the drawing area. In the pop-up
menu that comes up, choose Labels. Alternatively, one may access
this option by selecting the View menu followed by the Structure
Diagrams option from the top menu bar, and the Labels tab of the
dialog box that comes up.

Figure 1. 16
1-24 Tutorial 1

2. In the Diagrams dialog box that appears, turn the Node Numbers
and Beam Numbers on and then click on OK.

Figure 1. 17
 Tutorial 1 1-25
The following figure illustrates the node and beam numbers
displayed on the structure. The structure in the main window should
resemble the figure shown below.

Figure 1. 18

If you are feeling adventurous, here is a small exercise for you. Change the
font of the node/beam labels by going to the View menu and selecting the
Options command, and then selecting the
appropriate tab (Node Labels / Beam labels) from the Options
dialog box.
1-26 Tutorial 1

1.5.3 Specifying member properties

Our next task is to assign cross section properties for the beams
and columns (see figure in section 1.2). For those of us curious to know
the equivalent commands in the STAAD command file, they are :

MEMBER PROPERTY AMERICAN

1 3 TABLE ST W12X35
2 TABLE ST W14X34

Steps:

1. To define member properties, click on the Property Page icon

located on the top toolbar.

Figure 1. 19
 Tutorial 1 1-27
Alternatively, one may go to the General | Property page from the left
side of the screen as shown below.

Figure 1. 20
1-28 Tutorial 1

2. In either case, the Properties dialog box comes up (see figure

below). The property type we wish to create is the W shape from the
AISC table. This is available under the Section Database button in the
Properties dialog box as shown below. So, let us
click on the Section Database button.

Figure 1. 21
 Tutorial 1 1-29
3. In the Section Profile Tables dialog box that comes up, select W
Shape under the American option. Notice that the Material box is
checked. Let us keep it that way because it will enable us to
subsequently assign the material constants E, Density, Poisson, etc. along
with the cross-section since we want to assign the default
values.

Choose W12X35 as the beam size, and ST as the section type.

Then, click on the Add button as shown in the figure below.
Detailed explanation of the terms such as ST, T, CM, TC, BC, etc.
is available in Section 5 of the STAAD Technical Reference
Manual.

Figure 1. 22

4. To create the second member property (ST W14X34), select the

W14X34 shape and click on the Add button.

After the member properties have been created, let us Close the
Section Profile Tables dialog box.
1-30 Tutorial 1

5. The next step is to associate the properties we just created with

selected members in our model. Follow these steps.

a. Select the first property reference in the Properties dialog

box (W12X35).
b. Make sure that the “Use Cursor to Assign” button is
selected under the Assignment Method box.

c. Click on the Assign button. The cursor changes to

d. Using the cursor, click on members 1 and 3.
e. Finally, click on the Assign button again, or click on the
‘Esc’ button on your keyboard to stop the assignment
process.

Figure 1. 23

6. In a similar fashion, assign the second property reference

(W14X34) to member 2.
 Tutorial 1 1-31
After both the properties have been assigned to the respective
members, our model should resemble the following figure.

Figure 1. 24

Let us once again save our structure by pulling down the File menu and
selecting the Save command.
1-32 Tutorial 1

1.5.4 Specifying material constants

In Section 1.5.3, we kept the Material check box “on” while
assigning the member properties. Consequently, the material
constants got assigned to the members along with the properties, and the
following commands were generated in the command file:

CONSTANTS
E 29000 MEMB 1 TO 3
POISSON 0.3 MEMB 1 TO 3
DENSITY 0.000283 MEMB 1 TO 3
ALPHA 6.5e-006 MEMB 1 TO 3

Hence, there is no more a need to assign the constants separately.

However, if we hadn’t assign them as before, we could go to the menu
option Commands | Material Constants and assign them
explicitly as shown in the figure below.

Figure 1. 25
 Tutorial 1 1-33

1.5.5 Changing the input units of length

For specifying member offset values, as a matter of convenience, it
is simpler if our length units are inches instead of feet. The
commands to be generated are:

UNIT INCHES KIP

Steps:

1. To change the length units from feet to inch, click on the Input
Units icon from the appropriate toolbar.

Figure 1. 26

Alternatively, one may select the Tools | Set Current Input Unit
menu option as shown in the next figure.
1-34 Tutorial 1

Figure 1. 27

2. In either case, the following dialog box comes up. Set the Length
Units to Inch and click on the OK button.

Figure 1. 28
 Tutorial 1 1-35

1.5.6 Specifying member offsets

Since beam 2 actually spans only the clear distance between the
column faces, and not the center to center distance, we can take
advantage of this aspect by specifying offsets. Member 2 is
OFFSET at its START joint by 6 inches in the global X direction,
0.0 and 0.0 in Y and Z directions. The same member is offset by
negative 6.0 inches at its END joint. The corresponding STAAD
commands are:

MEMBER OFFSET
2 START 6.0 0.0 0.0
2 END -6.0 0.0 0.0

Steps:

1. Since we know that member 2 is the one to be assigned with the

offset, let us first select this member prior to defining the offset
itself. Select member 2 by clicking on it using the Beams Cursor
. The selected member will be highlighted. (Please refer to the
‘Frequently Performed Tasks’ section at the end of this manual to learn
more about selecting members.)

2. To define member offsets, click on the Specification Page icon

located in the top toolbar.

Figure 1. 29
1-36 Tutorial 1

Alternatively, one may go to the General | Spec Page from the left side of
the screen.

Figure 1. 30
 Tutorial 1 1-37
3. In either case, the Specifications dialog box shown below comes
up. Member Releases and Offsets are defined through the Beam
button in this dialog box as shown below.

Figure 1. 31
1-38 Tutorial 1

4. In the Beam Specs dialog box that opens, select the Offset tab. We
want to define the offset at the start node in the X direction. Hence,
make sure that the Start option is selected under Location . Then,
enter 6.0 in the X edit box. Since we have already selected the
member, let us click on the Assign button.

Figure 1. 32

5. To apply the offset at the end node, repeat steps 3 and 4, except for
selecting the End option and providing -6.0 in the X edit box.
 Tutorial 1 1-39
After both the Start and End offsets have been assigned, the model
will look as shown below.

Figure 1. 33

Click anywhere in the drawing area to un-highlight the member.

Let us save the work again by pulling down the File menu and
selecting the Save command.
1-40 Tutorial 1

1.5.7 Printing member information in the

output file
We would like to get a report consisting of information about all
the members including start and end joint numbers (incidence),
member length, beta angle and member end releases in the STAAD
output file. The corresponding STAAD command is:

PRINT MEMBER INFORMATION ALL

Steps:

1. Since the information is required for all the members, select all the
members by going to Select | By All | All Beams menu option.

Figure 1. 34
 Tutorial 1 1-41
2. Then, go to Commands | Pre Analysis Print | Member
Information from the top menu bar as shown in the figure below.

Figure 1. 35
1-42 Tutorial 1

3. Notice that the assignment method is set To Selection. Press the

OK button in this dialog box.

Figure 1. 36

Click anywhere in the drawing area to un-highlight the members.

Let us also save our structure again by using the Save option of the
File menu.
 Tutorial 1 1-43

1.5.8 Specifying Supports

The specifications of this problem (see section 1.2) call for
restraining all degrees of freedom at node 1 (FIXED support) and a pinned
type of restraint at node 4 (restrained against all
translations, free for all rotations) The commands to be generated are :

SUPPORTS
1 FIXED ; 4 PINNED

Steps:

1. To create a support, click on the Support Page icon located in the

top toolbar as shown below.

Figure 1. 37
1-44 Tutorial 1

Alternatively, one may go to the General | Support Page from the

left side of the screen.

Figure 1. 38
 Tutorial 1 1-45
2. In either case, the Supports dialog box comes up as shown in the
next figure. Since we already know that node 1 is to be associated

with a Fixed support, using the Nodes Cursor , select node 1.

It becomes highlighted. (Please refer to the ‘Frequently Performed Tasks’
section at the end of this manual to learn more about
selecting nodes.)

3. Then, click on the Create button in the Supports dialog box as

shown below.

Figure 1. 39
1-46 Tutorial 1

4. In the Create Support dialog box that opens, select the Fixed tab
(which also happens to be the default) and click on the Assign
button as shown below. This creates a FIXED type of support at node 1
where all 6 degrees of freedom are restrained.

Figure 1. 40

5. To create a PINNED support at node 4, repeat steps 2 to 4, except

for selecting node 4 and selecting the Pinned tab in the Create
Support dialog box.
 Tutorial 1 1-47
After the supports have been assigned, the structure will look like the one
shown below.

Figure 1. 41

After assigning both the supports, let us save our structure using the
File | Save option.
1-48 Tutorial 1

1.5.9 Viewing the model in 3D

Let us see how we can display our model in 3D. To do this, either right-
click and select Structure Diagrams or go to View |
Structure Diagrams menu.

Figure 1. 42

In the ensuing dialog box, the Structure tab page allows you to set
up structural view parameters as explained below.

The options under 3D Sections control how the members are

displayed. Selecting None displays the structure without displaying the
cross-sectional properties of the members and elements.
Selecting Full Sections displays the 3D cross-sections of members,
depending on the member properties. Sections Outline displays
only the outline of the cross-sections of members.

Let us select Full Sections to draw the 3D sections. You can also change
the color of the sections by clicking on the Section Outline color button
under the Colors section. Then, click on OK.
 Tutorial 1 1-49

Figure 1. 43

The resulting diagram is shown below.

Figure 1. 44
1-50 Tutorial 1

1.5.10 Specifying Loads

Three load cases are to be created for this structure. Details of the
individual cases are explained at the beginning of this tutorial. The
corresponding commands to be generated are listed below.

UNIT FEET KIP

LOADING 1 DEAD + LIVE

MEMBER LOAD
2 UNI GY -2.5

LOADING 2 WIND FROM LEFT

JOINT LOAD
2 FX 10.

LOAD COMBINATION 3 75 PERCENT OF (DL+LL+WL)

1 0.75 2 0.75

Steps:

The creation and assignment of load cases involves the following two
steps:

a. First, we will be creating all 3 load cases.

b. Then, we will be assigning them to the respective
members/nodes.

Creating load cases 1 and 2

1. To create loads, first click on the Load Page icon located on the
top tool bar.

Figure 1. 45
 Tutorial 1 1-51
Alternatively, one may go to the General | Load Page from the left side of
the screen.

Figure 1. 46

2. Before we create the first load case, we need to change our length
units to feet. To do that, as before, utilize the Input Units icon
(see section 1.5.5).

Notice that a window titled “Load” appears on the right-hand side

of the screen. To create the first load case, highlight Load Cases
Details and then click on the Add button in the Load dialog box.

Figure 1. 47
1-52 Tutorial 1

3. The Add New Load Cases dialog box comes up.

The drop-down list box against Loading Type is available in case

we wish to associate the load case we are creating with any of the
ACI, AISC or IBC definitions of Dead, Live, Ice, etc. This type of
association needs to be done if we intend to use the program's
facility for automatically generating load combinations in
accordance with those codes. Notice that there is a check box
called Reducible per UBC/IBC. This feature becomes active only when
the load case is assigned a Loading Type called Live at the time of
creation of that case. Please refer to STAAD.Pro 2004
Release Report for further details.

As we do not intend to use the automatic load combination

generation option, we will leave the Loading Type as None. Enter DEAD
+ LIVE as the Title for Load Case 1 and click on the Add button.

Figure 1. 48

The newly created load case will now appear under the Load Cases Details
option.

Figure 1. 49
 Tutorial 1 1-53
To create the Member load, first highlight DEAD + LIVE. You will
notice that the Add New Load Items dialog box shows more options
now.

Figure 1. 50

4. In the Add New Load Items dialog box, select the Uniform Force
option under the Member Load item. Specify GY as the Direction,
enter -2.5 as the Force and click on the Add button.

Figure 1. 51
1-54 Tutorial 1

The next step is to create the second load case which contains a joint
load.

5. Highlight Load Cases Details in the Load dialog box. In the Add
New Load Cases dialog box, once again, we are not associating the
load case we are about to create with any code based Loading Type
and so, leave that box as None. Specify the Title of the second load
case as WIND FROM LEFT and click on the Add button.

Figure 1. 52

6. Next, to create the Joint load, highlight WIND FROM LEFT.

Figure 1. 53
 Tutorial 1 1-55
7. In the Add New Load Items dialog box, select the Node option
under the Nodal Load item. Specify 10 for Fx, and click on the
Add button.

Figure 1. 54
1-56 Tutorial 1

Creating load case 3

Load cases 1 and 2 were primary load cases. Load case 3 will be defined
as a load combination. So, the next step is to define load case 3 as 0.75 x
(Load 1 + Load 2), which is a load combination.

8. To do this, once again, highlight the Load Cases Details option. In

the Add New Load Cases dialog box, click on the Define
Combinations option from the left-hand side. Specify the Title as
75 Percent of [DL+LL+WL].

Figure 1. 55

In the Define Combinations box, the default load combination type

is set to be Normal, which means an algebraic combination. The
other combination types available are called SRSS (square root of sum of
squares) and ABS (Absolute). The SRSS type offers the
flexibility of part SRSS and part Algebraic. That is, some load cases
are combined using the square root of sum of squares
approach, and the result is combined with other cases algebraically,
as in

A + SQRT(B*B + C*C)
where A, B and C are the individual primary cases.

We intend to use the default algebraic combination type (Normal).

 Tutorial 1 1-57
9. In the Define Combinations box, select both load cases from the
left side list box (by holding down the ‘Ctrl’ key) and click on the
button. The load cases appear in the right side list box. Then,
enter 0.75 in the Factor edit box. (These data indicate that we are
adding the two load cases with a multiplication factor of 0.75 and that the
load combination results would be obtained by algebraic
summation of the results for individual load cases.) Press the Add
button.

Figure 1. 56

Now that we have completed the task of creating all 3 load cases,
let us Close the Add New Load Cases dialog box.
1-58 Tutorial 1

Our next step is to associate load case 1 with member 2. Follow these
steps.

a. Select the first load reference in the Load dialog box (UNI
GY -2.5 kip/ft).
b. Make sure that the “Use Cursor to Assign” button is
selected under the Assignment Method box.

c. Click on the Assign button. The cursor changes to

d. Using the cursor, click on member 2.
e. Finally, click on the Assign button again, or type the ‘Esc’
button on your keyboard to stop the assignment process.

Figure 1. 57
 Tutorial 1 1-59
After the member load has been assigned, the model will look as shown
below.

Figure 1. 58

In a similar fashion, assign the second load case (FX 10 kip, ft) to Node
2.

After assigning the joint load, the model will look as shown below.

Figure 1. 59

Let us once again save our model by pulling down the File menu and
selecting the Save command or by holding the ‘Ctrl’ key and pressing
the ‘S’ key.
1-60 Tutorial 1

1.5.11 Specifying the analysis type

The analysis type we are required to do is a linear static type. We also
need to obtain a static equilibrium report. This requires the command:

PERFORM ANALYSIS PRINT STATICS CHECK

Steps:

1. To specify the Analysis command, go to Analysis/Print Page from

the left side of the screen. By default, the Analysis sub-page from
the second row is in focus as shown below.

Figure 1. 60
 Tutorial 1 1-61
2. In the Analysis/Print Commands dialog box that appears, make
sure that the Perform Analysis tab is selected. Then, check the
Statics Check print option. Finally, click on the Add button
followed by the Close button.

Figure 1. 61

Let us save the data once again using the File | Save option.
1-62 Tutorial 1

1.5.12 Specifying post-analysis print

commands
We would like to obtain the member end forces and support
reactions written into the output file. This requires the
specification of the following commands:

PRINT MEMBER FORCES ALL

PRINT SUPPORT REACTION LIST 1 4

Steps:

1. The dialog box for specifying the above commands is nested in the
Post-Print sub-page of the Analysis/Print page.

Figure 1. 62
 Tutorial 1 1-63
2. Next, select all the members by rubber-banding around them
using the mouse.

3. Click on the Define Commands button in the data area on the right
hand side of the screen.

Figure 1. 63
1-64 Tutorial 1

4. In the Analysis/Print Commands dialog box that appears, select the

Member Forces tab and click on the Assign button followed by the
Close button.

Figure 1. 64

5. Repeat steps 2 to 4 except for selecting both the supports and

selecting the Support Reactions tab in the Analysis/Print
Commands dialog box. (Recall that the supports can be selected by
turning the Nodes Cursor on, holding the ‘Ctrl’ key down, and
clicking on the supports.) After clicking on the Assign button,
Close the dialog box.
 Tutorial 1 1-65
At this point, the Post Analysis Print dialog box should resemble the
figure shown below.

Figure 1. 65

Save the work using the File | Save menu option.

1-66 Tutorial 1

1.5.13 Short-listing the load cases to be used

in steel design
The steel design has to be performed for load cases 1 and 3 only
per the specification at the beginning of this tutorial. To instruct
the program to use just these cases, and ignore the remaining, we
have to use the LOAD LIST command.

The command will appear in the STAAD file as :

LOAD LIST 1 3

Steps:

1. In the menus on the top of the screen, go to Commands | Loading

| Load List option as shown below.

Figure 1. 66
 Tutorial 1 1-67
2. A Load List dialog box comes up. From the Load Cases list box on
the left, double click on 1: DEAD + LIVE and 3: 75 Percent of
[DL+LL+WL] to send them to the Load List box on the right, as shown
below. Then click on the OK button to dismiss the dialog box.

Figure 1. 67
1-68 Tutorial 1

1.5.14 Specifying steel design parameters

The specifications listed in section 1.2 of this tutorial require us to
provide values for some of the terms used in steel design because
the default values of those terms are not suitable. The
corresponding commands to be generated are:

PARAMETER
CODE AISC
FYLD 5760 ALL
UNT 10.0 MEMB 2 3
UNB 10.0 MEMB 23
TRACK 2 MEMB 2 3
SELECT MEMB 2 3

Steps:

1. To specify steel design parameters, go to Design | Steel Page from

the left side of the screen. Make sure that under the Current Code
selections on the top right hand side, AISC ASD is selected.

Figure 1. 68
 Tutorial 1 1-69
2. Click on the Define Parameters button in the Steel Design dialog
box.

Figure 1. 69

3. In the Design Parameters dialog box that comes up, select the
FYLD option. Then, provide the Yield Strength as 5760 Kip/ft2
and click on the Add button.

Figure 1. 70
1-70 Tutorial 1

4. To define the remaining parameters, repeat step 3 except for

selecting the parameters and providing the values listed below.

Parameter Value

UNT 10

UNB 10

TRACK 2

5. When all the parameters have been added, click on the Close
button in the Design Parameters dialog box.

6. The next step is to assign these parameters to specific members of

the model. From looking at the requirements listed in the beginning
of this tutorial, we know that the FYLD parameter is to be assigned
to all the members, while the remaining parameters are to assigned
to members 2 and 3.

As before, use the Use Cursor to Assign method to assign these

parameters.

Figure 1. 71
 Tutorial 1 1-71
After all the design parameters have been assigned, the Steel
Design dialog box will look as shown below.

Figure 1. 72
1-72 Tutorial 1

7. To specify the SELECT command, click on the Commands button

in the Steel Design dialog box as shown below. The SELECT
command is an instruction to the program to fetch and assign the
least-weight cross-section which satisfies all the code requirements
(PASSes) for the member.

Figure 1. 73
 Tutorial 1 1-73
8. In the Design Commands dialog box that appears, click on the
SELECT option. Then, click on the Add button followed by the
Close button.

Figure 1. 74

9. Once again, we need to associate this command with members 2

and 3. You may either use the Use Cursor to Assign method or
first select members 2 and 3 and then use the Assign to Selected
Beams option.

After the parameters are assigned, click anywhere in the drawing area to
un-highlight the members.

Let us save our structure by pulling down the File menu and
selecting the Save command.
1-74 Tutorial 1

1.5.15 Re-specifying the analysis command

When the analysis & design engine executes the member selection
operation we specified in the previous step, a new set of properties
will end up being assigned to those members. This has the effect of
changing the stiffness distribution for the entire structure. Since
the structure is statically indeterminate, we ought to re-analyze it if
we want the nodal displacements, member forces, etc. to reflect
this new stiffness distribution. The command to be generated is
hence:

PERFORM ANALYSIS

Steps:

1. To specify the Analysis command, repeat step 1 of Section 1.5.11

of this tutorial. In the Analysis/Print Commands dialog box that
comes up, select the Perform Analysis tab. Since we are not
interested in a statics check report once again, let us check the No Print
option. Finally, click on the Add button followed by the
Close button.

We should again save the work using File | Save.

 Tutorial 1 1-75

1.5.16 Re-specifying the TRACK parameter

The final calculation we need to do is make sure the current set of
member properties pass the code requirements based on the up-to- date
member forces. This will require that we do a code checking operation
again. To restrict the output produced to a reasonable
level, we specify the TRACK parameter again as:

TRACK 1 ALL

Steps:

1. To define and assign 1.0 for the TRACK parameter, repeat steps 1
to 4 of Section 1.5.14 of this tutorial.
2. Next, select all the members by rubber-banding around them
using the mouse. (Please refer to the ‘Frequently Performed Tasks’ section
at the end of this manual to learn more about selecting members.) Then,
assign this parameter to all the members.
1-76 Tutorial 1

1.5.17 Re-specifying the CHECK CODE

command
The analysis operation carried out in response to the command in
Section 1.5.15 will create a new set of member forces. These forces
will very likely be quite different from those which were used in
the member selection operation (see the commands of section
1.5.14). Consequently, we have to verify that the structure is safely able –
from the standpoint of the design code requirements – to
carry these new forces. A code checking operation, which uses the up-to-
date cross sections of the members, and the latest member
forces, will provide us with a status report on this issue. The
command to be generated is hence:

CHECK CODE ALL

Steps:

1. If you have wandered away from the Steel Design page, from the
Commands menu on top of the screen, select Design | Steel
Design.
 Tutorial 1 1-77
2. Click on the Commands button in the Steel Design dialog box as
shown below.

Figure 1. 75
1-78 Tutorial 1

3. In the Design Commands dialog box that appears, click on the

Check Code tab. Then, click on the Add button followed by the
Close button.

Figure 1. 76

4. Since the CHECK CODE command has to be assigned to all the

members, the easiest way to do that is to click on the Assign to
View button.

Figure 1. 77

We have now completed the tasks for assigning the input for this model.
Let us save the file one last time using the File | Save
option.
 Tutorial 1 1-79

1.6 Viewing the input command file

Steps:

Let us now take a look at the data that has been written into the file
that we just saved earlier. The contents of the file can be viewed
either by clicking on the STAAD Editor icon or, by going to the
Edit menu and choosing Edit Input Command File as shown below.

Figure 1. 78

Figure 1. 79
1-80 Tutorial 1

A new window will open up with the data listed as shown here:

Figure 1. 80

This window and the facilities it contains is known as the STAAD Editor.
 Tutorial 1 1-81
We could make modifications to the data of our structure in this
Editor if we wish to do so. Let us Exit the Editor without doing so
by selecting the File | Exit menu option of the editor window (not
the File | Exit menu of the main window behind the editor
window).

As we saw in Section 1.1, we could also have created the same model
by typing the relevant STAAD commands into a text file
using either the STAAD editor, or by using any external editor of our
choice. If you would like to understand that method, proceed
to the next section. If you want to skip that part, proceed to section
1.8 where we perform the analysis and design on this model.
1-82 Tutorial 1

1.7 Creating the model using the command file

Let us now use the command file method to create the model for
the above structure. The commands used in the command file are
described later in this section.

The STAAD.Pro command file may be created using the built-in editor,
the procedure for which is explained further below in this
section. Any standard text editor such as Notepad or WordPad may also be
used to create the command file. However, the STAAD.Pro command file
editor offers the advantage of syntax checking as we type the commands.
The STAAD.Pro keywords, numeric data,
comments, etc. are displayed in distinct colors in the STAAD.Pro
editor. A typical editor screen is shown below to illustrate its general
appearance.

Figure 1. 81
 Tutorial 1 1-83
To access the built-in editor, first start the program using the
procedure explained in Section 1.3. Next, follow step 1 of Section 1.4.

Figure 1. 82

You will then encounter the dialog box shown in the figure shown below.
In that dialog box, choose Open STAAD Editor.

Figure 1. 83
1-84 Tutorial 1

At this point, the editor screen similar to the one shown below will open.

Figure 1. 84

Delete all the command lines displayed in the editor window and
type the lines shown in bold below (You don’t have to delete the
lines if you know which to keep and where to fill in the rest of the
commands). The commands may be typed in upper or lower case
letters. Usually the first three letters of a keyword are all that are needed
-- the rest of the letters of the word are not required. The required letters
are underlined. (“PLANE” = “PLA” = “plane” = “pla”)
 Tutorial 1 1-85
STAAD PLANE PORTAL FRAME

Every STAAD.Pro input file has to begin with the word STAAD. The
word PLANE signifies that the structure is a plane frame (in the XY
plane). The remainder of the words are the title of the
problem, which is optional.

If a line is typed with an asterisk in the first column, it signifies that the
line is a comment line and should not be executed. For
example, one could have put the optional title above on a separate line as
follows.

* PORTAL FRAME

UNIT FEET KIP

Specify the force and length units for the commands to follow.

JOINT COORDINATES
1 0. 0. ; 2 0. 15. ; 3 20. 15. ; 4 20. 0.

Joint numbers and their corresponding global X and Y coordinates

are provided above. For example, 3 20 15. indicates that node 3 has
an X coordinate of 20 ft and a Y coordinate of 15 ft. Note that the
reason for not providing the Z coordinate is because the structure
is a plane frame. If this were a space frame, the Z coordinate would
also be required. Semicolons (;) are used as line separators. In
other words, data which is normally put on multiple lines can be
put on one line by separating them with a semicolon.

MEMBER INCIDENCE
112;223;334

The members are defined by the joints to which they are connected.
1-86 Tutorial 1
MEMBER PROPERTY AMERICAN
1 3 TABLE ST W12X35
2 TABLE ST W14X34

Members 1 and 3 are assigned a W12X35 section from the built-in

AMERICAN steel table. Member 2 has been assigned a W14X34. The
word ST stands for standard single section. Sections 5.20.1 through 5.20.5
of the STAAD Technical Reference Manual explain the convention for
assigning member property names.

UNIT INCHES
CONSTANTS
E 29000.0 ALL
POISSON 0.3 ALL

The length unit is changed from FEET to INCHES to facilitate

input of the modulus of elasticity (E). The keyword CONSTANT is
required before material properties such as E, density, Poisson’s
ratio, coefficient of thermal expansion (ALPHA) etc. can be
provided. See Section 5.26 of the STAAD Technical Reference
Manual for more information.

MEMBER OFFSET
2 START 6.0 0. 0.
2 END -6.0 0. 0.

The beam member is physically connected to the 2 columns at the

face of the column, and not at the column centerline. This creates a
rigid zone, about half the depth of the columns, at the 2 ends of the
beam 2. This rigid zone is taken advantage of using member offsets
(It is the user’s choice whether or not he/she wishes to use these).
So, the above commands define that member 2 is eccentrically
connected or OFFSET at its START joint by 6 inches in the global
X direction, 0.0 and 0.0 in Y and Z directions. The same member is
offset by negative 6.0 inches at its END joint. See Section 5.25 of
the STAAD Technical Reference Manual for more information.
 Tutorial 1 1-87
PRINT MEMBER INFORMATION ALL

The above command is self-explanatory. The information that is printed

includes start and end joint numbers (incidence), member length, beta
angle and member end releases.

SUPPORTS
1 FIXED ; 4 PINNED

A fixed support is located at joint 1 and a pinned support (fixed for

translations, released for rotations) at joint 4. More information on the
support specification is available in Section 5.27 of the STAAD Technical
Reference Manual.

UNIT FT

The length unit is changed to FEET to facilitate input of loads.

LOADING 1 DEAD + LIVE

MEMBER LOAD
2 UNI GY -2.5

The above commands identify a loading condition. DEAD + LIVE

is an optional title to identify this load case. A UNIformly
distributed MEMBER LOAD of 2.5 kips/ft is acting on member 2
in the negative global Y direction. Member Load specification is
explained in Section 5.32 of the STAAD Technical Reference
Manual.

LOADING 2 WIND FROM LEFT

JOINT LOAD
2 FX 10.

The above commands identify a second load case. This load is a JOINT
LOAD. A 10 kip force is acting at joint 2 in the global X direction.
1-88 Tutorial 1
LOAD COMBINATION 3 75 PERCENT OF (DL+LL+WL)
1 0.75 2 0.75

This command identifies a combination load with an optional title. The

second line provides the components of the load combination case -
primary load cases and the factors by which they should be individually
multiplied.

PERFORM ANALYSIS PRINT STATICS CHECK

This command instructs the program to proceed with the analysis and
produce a report of static equilibrium checks. Section 5.37 of
the STAAD Technical Reference Manual offers information on the
various analysis options available.

PRINT MEMBER FORCES ALL

PRINT SUPPORT REACTION LIST 1 4

The above print commands are self-explanatory. The member

forces are in the member local axes while support reactions are in the
global axes.

LOAD LIST 1 3
PARAMETERS
CODE AISC
UNT 10.0 MEMB 2 3
UNB 10.0 MEMB 2 3
FYLD 5760 ALL
TRACK 2.0 MEMB 2 3
SELECT MEMBER 2 3

The above sequence of commands is used to initiate the steel

design process. The command PARAMETERS is followed by the
various steel design parameters. Parameters are specified typically
when their values differ from the built-in program defaults.
Specifications of the AISC ASD code are to be followed. A
parameter list for the AISC code is available in Table 3.1 of the
Technical Reference Manual. ALL members have 10 ft
unsupported length for the top and bottom flange (UNT and UNB).
UNT and UNB are used to compute the allowable compressive
stress in bending. The yield strength of steel is specified as 5760
 Tutorial 1 1-89
ksf (40 ksi) since it is different from the default value of 36 ksi.
The TRACK parameter controls the level of description of the output,
2.0 being the most detailed. The LOAD LIST command
lists the load cases (1 and 3) to be used in the design. The SELECT
MEMBER command asks the program to come up with the most
economical section for members 2 and 3 in the context of the above
analysis.

PERFORM ANALYSIS

When the analysis & design engine executes the member selection
operation we specified in the previous step, a new set of properties
will end up being assigned to those members. This has the effect of
changing the stiffness distribution for the entire structure. Since
the structure is statically indeterminate, we ought to re-analyze it if
we want the nodal displacements, member forces, etc. to reflect
this new stiffness distribution. The above command instructs the
program to do another cycle of analysis.

PARAMETER
TRACK 1 ALL

The TRACK parameter is re-specified. It controls the level of

information produced in the steel design output. We have lowered
it from 2.0 we specified earlier to 1.0 since we aren’t interested in
the highest level of detail at this time.

CHECK CODE ALL

The analysis operation carried out earlier will create a new set of
member forces. These forces will very likely be quite different
from those which were used in the member selection operation.
Consequently, we have to verify that the structure is safely able –
from the standpoint of the design code requirements – to carry
these new forces. A code checking operation, which uses the up-to-
date cross sections of the members, and the latest member forces,
will provide us with a status report on this issue.

FINISH
1-90 Tutorial 1

A STAAD run is terminated using the FINISH command.

Save the file and return to the main screen.

This concludes the session on generating our model as a command

file using the built-in editor. If you wish to perform the analysis
and design, you may proceed to the next section of this manual. The on-
screen post-processing facilities are explained in Section 1.10.

(Remember that without successfully completing the analysis

and design, the post-processing facilities will not be accessible.)
 Tutorial 1 1-91

1.8 Performing Analysis/Design

STAAD.Pro performs Analysis and Design simultaneously. In order
to perform Analysis and Design, select the Run Analysis option from
the Analyze menu.

Figure 1. 85

If the structure has not been saved after the last change was made, you
should save the structure first by using the Save command
from the File menu.

When you select the Run Analysis option from the Analyze menu, the
following dialog box appears:

Figure 1. 86

We are presented with the choice of 2 engines : the STAAD engine and the
STARDYNE Advanced Analysis engine. The STARDYNE Analysis
engine is suitable for advanced problems such as
Buckling Analysis, Modal Extraction using various methods, etc.
However, if the calculations call for steel or concrete design, UBC
load generation, etc., we have to select the STAAD engine. So, let
us ensure that the radio button is on the STAAD engine.
1-92 Tutorial 1

Click on the Run Analysis button.

As the analysis progresses, several messages appear on the screen

as shown in the figure below.

Figure 1. 87

Notice that we can choose from the three options available in the above
dialog box:

Figure 1. 88
 Tutorial 1 1-93
These options are indicative of what will happen after we click on the
Done button.

The View Output File option allows us to view the output file
created by STAAD. The output file contains the numerical results
produced in response to the various input commands we specified
during the model generation process. It also tells us whether any
errors were encountered, and if so, whether the analysis and design
was successfully completed or not. Section 1.9 offers additional
details on viewing and understanding the contents of the output file.

The Go to Post Processing Mode option allows us to go to

graphical part of the program known as the Post-processor. This is where
one can extensively verify the results, view the results
graphically, plot result diagrams, produce reports, etc. Section 1.10
explains the Post processing mode in greater detail.

The Stay in Modelling Mode lets us continue to be in the Model

generation mode of the program (the one we currently are in) in
case we wish to make further changes to our model.
1-94 Tutorial 1

1.9 Viewing the output file

During the analysis process, STAAD.Pro creates an Output file. This file
provides important information on whether the analysis were performed
properly. For example, if STAAD.Pro encounters an instability problem
during the analysis process, it will be
reported in the output file.

We can access the output file using the method explained at the
end of the previous section. Alternatively, we can select the File | View |
Output File | STAAD Output option from the top menu.
The STAAD.Pro output file for the problem we just ran is shown in the
next few pages.

Figure 1. 89
 Tutorial 1 1-95
The STAAD.Pro output file is displayed through a file viewer
called SproView. This viewer allows us to set the text font for the
entire file and print the output file to a printer. Use the appropriate
File menu option from the menu bar.

Figure 1. 90

By default, the output file contains a listing of the entire Input

also. You may choose not to print the echo of the Input commands
in the Output file. Please select Commands | Miscellaneous | Set
Echo option from the menu bar and select the Echo Off button.

It is quite important that we browse through the entire output file

and make sure that the results look reasonable, that there are no
error messages or warnings reported, etc. Errors encountered
during the analysis & design can disable access to the post-
processing mode – the graphical screens where results can be
viewed graphically. The information presented in the output file is
a crucial indicator of whether or not the structure satisfies the
engineering requirements of safety and serviceability.
1-96 Tutorial 1

****************************************************
* *
* STAAD.Pro *
* Version Bld *
* Proprietary Program of *
* Research Engineers, Intl. *
* Date= *
* Time= *
* *
* USER ID: *
****************************************************

1. STAAD PLANE PORTAL FRAME

2. START JOB INFORMATION
3. ENGINEER DATE
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT FEET KIP
7. JOINT COORDINATES
8. 1 0 0 0; 2 0 15 0; 3 20 15 0; 4 20 0 0
9. MEMBER INCIDENCES
10. 1 1 2; 2 2 3; 3 3 4
11. DEFINE MATERIAL START
12. ISOTROPIC STEEL
13. E 4.176E+006
14. POISSON 0.3
15. DENSITY 0.489024
16. ALPHA 6.5E-006
17. DAMP 0.03
18. END DEFINE MATERIAL
19. MEMBER PROPERTY AMERICAN
20. 1 3 TABLE ST W12X35
21. 2 TABLE ST W14X34
22. CONSTANTS
23. MATERIAL STEEL MEMB 1 TO 3
24. UNIT INCHES KIP
25. MEMBER OFFSET
26. 2 START 6 0 0
27. 2 END -6 0 0
28. SUPPORTS
29. 1 FIXED
30. 4 PINNED
31. UNIT FEET KIP
32. LOAD 1 DEAD + LIVE
33. MEMBER LOAD
34. 2 UNI GY -2.5
35. LOAD 2 WIND FROM LEFT
36. JOINT LOAD
37. 2 FX 10
38. LOAD COMB 3 75 PERCENT OF {DL+LL+WL]
39. 1 0.75 2 0.75
40. PERFORM ANALYSIS PRINT STATICS CHECK

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS/MEMBER+ELEMENTS/SUPPORTS = 4/ 3/ 2
ORIGINAL/FINAL BAND-WIDTH= 1/ 1/ 6 DOF
TOTAL PRIMARY LOAD CASES = 2, TOTAL DEGREES OF FREEDOM = 7
SIZE OF STIFFNESS MATRIX = 1 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.0/ 3884.9 MB, EXMEM = 488.4 MB

STATIC LOAD/REACTION/EQUILIBRIUM SUMMARY FOR CASE NO. 1

DEAD + LIVE

***TOTAL APPLIED LOAD ( KIP FEET ) SUMMARY (LOADING 1 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = -47.50
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 0.00 MY= 0.00 MZ= -475.00
 Tutorial 1 1-97

***TOTAL REACTION LOAD( KIP FEET ) SUMMARY (LOADING 1 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = 47.50
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 0.00 MY= 0.00 MZ= 475.00

MAXIMUM DISPLACEMENTS ( INCH /RADIANS) (LOADING 1)

MAXIMUMS AT NODE
X = 1.82363E-01 2
Y = -1.46578E-02 3
Z = 0.00000E+00 0
RX= 0.00000E+00 0
RY= 0.00000E+00 0
RZ= -4.82525E-03 2

STATIC LOAD/REACTION/EQUILIBRIUM SUMMARY FOR CASE NO. 2

WIND FROM LEFT

***TOTAL APPLIED LOAD ( KIP FEET ) SUMMARY (LOADING 2 )

SUMMATION FORCE-X = 10.00
SUMMATION FORCE-Y = 0.00
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 0.00 MY= 0.00 MZ= -150.00

***TOTAL REACTION LOAD( KIP FEET ) SUMMARY (LOADING 2 )

SUMMATION FORCE-X = -10.00
SUMMATION FORCE-Y = 0.00
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 0.00 MY= 0.00 MZ= 150.00

MAXIMUM DISPLACEMENTS ( INCH /RADIANS) (LOADING 2)

MAXIMUMS AT NODE
X = 7.27304E-01 2
Y = 2.47268E-03 2
Z = 0.00000E+00 0
RX= 0.00000E+00 0
RY= 0.00000E+00 0
RZ= -5.48842E-03 4

************ END OF DATA FROM INTERNAL STORAGE ************

41. UNIT INCHES KIP

42. PRINT MEMBER INFORMATION ALL

MEMBER INFORMATION
------------------

MEMBER START END LENGTH BETA

JOINT JOINT (INCH) (DEG) RELEASES

1 1 2 180.000 0.00
2 2 3 228.000 0.00
3 3 4 180.000 0.00

************ END OF DATA FROM INTERNAL STORAGE ************

1-98 Tutorial 1
43. UNIT FEET KIP
44. PRINT MEMBER FORCES ALL

MEMBER END FORCES STRUCTURE TYPE = PLANE

-----------------
ALL UNITS ARE -- KIP FEET

MEMBER LOAD JT AXIAL SHEAR-Y SHEAR-Z TORSION MOM-Y MOM-Z

1 1 1 23.18 -3.99 0.00 0.00 0.00 -11.48

2 -23.18 3.99 0.00 0.00 0.00 -48.40
2 1 -4.10 7.68 0.00 0.00 0.00 67.93
2 4.10 -7.68 0.00 0.00 0.00 47.32
3 1 14.30 2.77 0.00 0.00 0.00 42.34
2 -14.30 -2.77 0.00 0.00 0.00 -0.81

2 1 2 3.99 23.18 0.00 0.00 0.00 36.81

3 -3.99 24.32 0.00 0.00 0.00 -47.72
2 2 2.32 -4.10 0.00 0.00 0.00 -45.27
3 -2.32 4.10 0.00 0.00 0.00 -32.69
3 2 4.73 14.30 0.00 0.00 0.00 -6.34
3 -4.73 21.32 0.00 0.00 0.00 -60.31

3 1 3 24.32 3.99 0.00 0.00 0.00 59.88

4 -24.32 -3.99 0.00 0.00 0.00 0.00
2 3 4.10 2.32 0.00 0.00 0.00 34.74
4 -4.10 -2.32 0.00 0.00 0.00 0.00
3 3 21.32 4.73 0.00 0.00 0.00 70.97
4 -21.32 -4.73 0.00 0.00 0.00 0.00

************** END OF LATEST ANALYSIS RESULT **************

45. PRINT SUPPORT REACTION LIST 1 4

SUPPORT REACTIONS -UNIT KIP FEET STRUCTURE TYPE = PLANE

-----------------

JOINT LOAD FORCE-X FORCE-Y FORCE-Z MOM-X MOM-Y MOM Z

1 1 3.99 23.18 0.00 0.00 0.00 -11.48

2 -7.68 -4.10 0.00 0.00 0.00 67.93
3 -2.77 14.30 0.00 0.00 0.00 42.34
4 1 -3.99 24.32 0.00 0.00 0.00 0.00
2 -2.32 4.10 0.00 0.00 0.00 0.00
3 -4.73 21.32 0.00 0.00 0.00 0.00

************** END OF LATEST ANALYSIS RESULT **************

46. LOAD LIST 1 3

47. PARAMETER
48. CODE AISC
49. FYLD 5760 MEMB 1 TO 3
50. UNT 10 MEMB 2 3
51. UNB 10 MEMB 2 3
52. TRACK 2 MEMB 2 3
53. SELECT MEMB 2 3
 Tutorial 1 1-99

STAAD.PRO MEMBER SELECTION - (AISC 9TH EDITION)

***********************************************

|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN INCH UNIT |
| * |=============================| ===|=== ------------ |
|MEMBER 2 * | | | AX = 8.85 |
| * | ST W14X30 | | --Z AY = 3.39 |
|DESIGN CODE * | | | AZ = 3.47 |
| AISC-1989 * =============================== ===|=== SY = 5.82 |
| * SZ = 42.05 |
| * |<---LENGTH (FT)= 19.00 --->| RY = 1.49 |
|************* RZ = 5.73 |
| |
| 70.5 (KIP-FEET) |
|PARAMETER | L1 L1 STRESSES |
|IN KIP INCH | L1 IN KIP INCH |
|--------------- + L3 -------------|
| KL/R-Y= 153.21 | L3 FA = 6.36 |
| KL/R-Z= 39.76 + fa = 0.45 |
| UNL = 120.00 | L3 L1 FCZ = 21.68 |
| CB = 1.00 +L1 FTZ = 24.00 |
| CMY = 0.85 | L3 L3 FCY = 30.00 |
| CMZ = 0.85 + FTY = 30.00 |
| FYLD = 40.00 | L1 fbz = 20.13 |
| NSF = 1.00 +---+---+---+---+---+---+---+---+---+---| fby = 0.00 |
| DFF = 0.00 13.8 Fey = 6.36 |
| dff = 0.00 ABSOLUTE MZ ENVELOPE Fez = 94.46 |
| (WITH LOAD NO.) FV = 16.00 |
| fv = 0.17 |
| |
| MAX FORCE/ MOMENT SUMMARY (KIP-FEET) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 4.7 24.3 0.0 0.0 70.5 |
| LOCATION 0.0 19.0 0.0 0.0 9.5 |
| LOADING 3 1 0 0 1 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY (KIP-FEET) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS AISC- H1-3 0.999 1 |
| 3.99 C 0.00 -70.55 9.50 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
1-100 Tutorial 1

STAAD.PRO MEMBER SELECTION - (AISC 9TH EDITION)

***********************************************

|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN INCH UNIT |
| * |=============================| ===|=== ------------ |
|MEMBER 3 * | | | AX = 10.00 |
| * | ST W14X34 | | --Z AY = 3.61 |
|DESIGN CODE * | | | AZ = 4.10 |
| AISC-1989 * =============================== ===|=== SY = 6.91 |
| * SZ = 48.64 |
| * |<---LENGTH (FT)= 15.00 --->| RY = 1.53 |
|************* RZ = 5.83 |
| |
| 71.0 (KIP-FEET) |
|PARAMETER |L3 STRESSES |
|IN KIP INCH | L3 IN KIP INCH |
|--------------- + L3 L3 -------------|
| KL/R-Y= 117.92 | L3 FA = 10.72 |
| KL/R-Z= 30.87 + fa = 2.13 |
| UNL = 120.00 | L3 L3 FCZ = 21.95 |
| CB = 1.00 + FTZ = 24.00 |
| CMY = 0.85 | L3 FCY = 30.00 |
| CMZ = 0.85 + L3 L3 FTY = 30.00 |
| FYLD = 40.00 | L0 fbz = 17.51 |
| NSF = 1.00 +---+---+---+---+---+---+---+---+---+---| fby = 0.00 |
| DFF = 0.00 -3.9 Fey = 10.74 |
| dff = 0.00 ABSOLUTE MZ ENVELOPE Fez = 156.71 |
| (WITH LOAD NO.) FV = 16.00 |
| fv = 1.31 |
| |
| MAX FORCE/ MOMENT SUMMARY (KIP-FEET) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 24.3 4.7 0.0 0.0 71.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 1 3 0 0 3 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY (KIP-FEET) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS AISC- H1-2 0.886 3 |
| 21.32 C 0.00 70.97 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
54. PERFORM ANALYSIS
55. PARAMETER
56. CODE AISC
57. TRACK 1 MEMB 1 TO 3
58. CHECK CODE MEMB 1 TO 3
 Tutorial 1 1-
101

STAAD.PRO CODE CHECKING - (AISC 9TH EDITION)

********************************************

ALL UNITS ARE - KIP FEET (UNLESS OTHERWISE NOTED)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

1 ST W12X35 PASS AISC- H1-1 0.855 1

23.02 C 0.00 52.01 15.00

-----------------------------------------------------------------------
| MEM= 1, UNIT KIP-INCH, L= 180.0 AX= 10.30 SZ= 45.6 SY= 7.5 |
| KL/R-Y= 116.7 CB= 1.00 YLD= 40.00 ALLOWABLE STRESSES: FCZ= 18.19 |
| FTZ= 24.00 FCY= 30.00 FTY= 30.00 FC= 10.94 FT= 24.00 FV= 16.00 |
-----------------------------------------------------------------------

2 ST W14X30 PASS AISC- H1-3 0.969 3

5.16 C 0.00 66.64 19.00

-----------------------------------------------------------------------
| MEM= 2, UNIT KIP-INCH, L= 228.0 AX= 8.85 SZ= 42.1 SY= 5.8 |
| KL/R-Y= 153.2 CB= 1.00 YLD= 40.00 ALLOWABLE STRESSES: FCZ= 21.68 |
| FTZ= 24.00 FCY= 30.00 FTY= 30.00 FC= 6.36 FT= 24.00 FV= 16.00 |
-----------------------------------------------------------------------

3 ST W14X34 PASS AISC- H1-2 0.959 3

21.45 C 0.00 77.36 0.00

-----------------------------------------------------------------------
| MEM= 3, UNIT KIP-INCH, L= 180.0 AX= 10.00 SZ= 48.6 SY= 6.9 |
| KL/R-Y= 117.9 CB= 1.00 YLD= 40.00 ALLOWABLE STRESSES: FCZ= 21.95 |
| FTZ= 24.00 FCY= 30.00 FTY= 30.00 FC= 10.72 FT= 24.00 FV= 16.00 |
-----------------------------------------------------------------------

59. FINISH
*********** END OF THE STAAD.Pro RUN ***********
**** DATE= TIME= ***
************************************************************
* For questions on STAAD.Pro, please contact *
* Research Engineers Offices at the following locations *
* *
* Telephone Email *
* USA: +1 (714)974-2500 [email protected] *
* CANADA +1 (905)632-4771 [email protected] *
* CANADA +1 (604)629 6087 [email protected] *
* UK +44(1454)207-000 [email protected] *
* FRANCE +33(0)1 64551084 [email protected] *
* GERMANY +49/931/40468-71 [email protected] *
* NORWAY +47 67 57 21 30 [email protected] *
* SINGAPORE +65 6225-6015/16 [email protected] *
* INDIA +91(033)2357-3575 [email protected] *
* JAPAN +81(03)5952-6500 [email protected] *
* CHINA +86(411)363-1983 [email protected] *
* *
* North America [email protected] *
* Europe [email protected] *
* Asia [email protected] *
************************************************************
1-102 Tutorial 1

1.10 Post-Processing
STAAD.Pro offers extensive result verification and visualization
facilities. These facilities are accessed from the Post Processing
Mode. The Post Processing mode is used to verify the analysis and
design results and generate reports.

For this tutorial problem, we shall perform the following tasks:

Display deflection diagrams

Annotate Displacements
Display the force and moment diagrams.
Change the degree of freedom for which the force/moment
diagram is plotted
Annotate the force diagram
Displaying dimensions of members 
 Tutorial 1 1-
103
1.10.1 Going to the post-processing mode
Steps:

1. At the end of section 1.8, we saw how one could go directly from
the Analysis window to the post-processing screen. However, the
formal method of accessing the Post Processing mode is either by
clicking on the Post-Processing icon from the top toolbar or from
the Mode menu as shown in the figures below.

Figure 1. 91

Figure 1. 92
1-104 Tutorial 1

2. The Results Setup dialog box appears as shown below. Select the
load cases for which to display the results. For this tutorial, let us
select all the load cases. Then click on the OK button.

Figure 1. 93
 Tutorial 1 1-105
Notice that in the Post-Processing mode, the tabbed Page Control
bar and the menu bar change to offer the post processing functions.

Page Control in Page Control in

Modeling Mode Post-Processing Mode

Figure 1. 94

Menu Bar in Modeling Mode

Menu Bar in Post-Processing Mode

Figure 1. 95
1-106 Tutorial 1

1.10.2 Annotating the displacements

Steps:

The screen will now look like the figure shown below.

Figure 1. 96

The diagram currently on display is the node deflection diagram for

load case 1 (DEAD + LIVE). The title at the bottom of the
diagram is indicative of that aspect. If you, say, wandered off into any
other result diagram, and wanted to get back to the deflection diagram,
just select the Node | Displacement tab along the page
control area on the left side.
 Tutorial 1 1-107

Figure 1. 97

Annotation is the process of displaying the displacement values on the

screen. Select the View Value option from the Results menu.

Figure 1. 98
1-108 Tutorial 1

The following dialog box comes up. From the Ranges tab, select
All nodes. If you wish to annotate deflection for just a few nodes,
specify the node numbers in the node list.

Figure 1. 99

We will annotate the results for all the nodes. So, keep the button
on All.
 Tutorial 1 1-109
From the Node tab, check the Resultant option. Resultant stands for the
square root of sum of squares of values of X,Y and Z
displacements. Click the Annotate button and notice that the
values appear on the structure. Click the Close button to close the dialog
box.

Figure 1. 100
1-110 Tutorial 1

The following figure shows the annotated deflection diagram for load
case 1.

Figure 1. 101
 Tutorial 1 1-111

1.10.3 Displaying force/moment diagrams

Steps:

The simplest method to access the facilities for displaying

force/moment diagrams is from the Beam | Forces page along the
page control area on the left side of the screen. The bending
moment MZ will be plotted by default, evidence of which can be
found in the form of the Mz icon show in the diagram below which
becomes active.

Figure 1. 102
1-112 Tutorial 1

Figure 1. 103
 Tutorial 1 1-113
The option for selecting the forces/moment diagram is available from
another facility also - the Results | Bending Moment menu option.

Figure 1. 104
1-114 Tutorial 1

1.10.4 Annotating the force/moment diagram

Steps:

Annotation is the process of displaying the force/moment values on the

screen. Select the View Value option from the Results menu.

Figure 1. 105

In the dialog box that comes up, click on the Ranges tab and select
All members. If you wish to annotate the force/moment for just a few
members, specify the beam numbers in the beam list.
 Tutorial 1 1-115

Figure 1. 106
We will annotate the results for all members. So, keep the button
on All.

From the Beam Results tab, check the Ends and Mid Point
options under the Bending section. Click the Annotate button and notice
that the values appear on the structure. Click the Close
button to close the dialog box.

Figure 1. 107
1-116 Tutorial 1

The following figure shows the annotated MZ diagram for load case 2.
Figure 1. 108
 Tutorial 1 1-117

1.10.5 Changing the degree of freedom for

which forces diagram is plotted
Force and moment diagrams can be plotted for 6 degrees of
freedom – Axial, Shear-Y, Shear-Z, Torsion, Moment-Y, Moment-
Z. One may select or de-select one of more of these degrees of
freedom from View | Structure Diagrams | Loads and Results. Let us
select Shear yy and select load case 3 (75 PERCENT OF
[DL+LL+WL] as shown below.

Figure 1. 109
1-118 Tutorial 1

The resulting figure is shown below.

Figure 1. 110

All degrees of freedom currently plotted will be indicated with a tick

mark in the Diagrams dialog box.

The icons of the Results toolbar may also be used to turn on/off
specific degrees of freedom.

Figure 1. 111
 Tutorial 1 1-119
For the sake of easy identification, each degree of freedom (d.o.f) has
been assigned a different color (see Diagrams dialog box
shown above). One may change the color for that d.o.f. by clicking
on the color button alongside the d.o.f, and make a new choice
from the color palette.

Figure 1. 112

The appearance of the diagram may also be set to one of the 3 –

Hatch, Fill or Outline by turning on the relevant option in the dialog
box shown earlier.

Figure 1. 113
1-120 Tutorial 1

1.10.6 Displaying the dimensions of the

members

To display the dimension of the members, click on the Dimension

icon. Alternatively, one may select the Dimension Beams option from
the Tools menu. In the dialog box that opens, the option
Dimension to View is active. Click on the Display button followed by the
Close button, and the dimensions of the members will
appear alongside the members.

Figure 1. 114

Figure 1. 115
 Tutorial 1 1-121
The diagram will look like the one shown below.

Figure 1. 116

We can opt to save the screenshot by clicking on the Take Picture

icon (shown below). This picture may be included in custom
reports. See Chapter 2 for a tutorial on taking pictures as well as
generating custom reports.

Figure 1. 117
1-122 Tutorial 1

For obtaining a quick print of the plot on the screen, select the
Print Current View icon as shown below.

Figure 1. 118
For detailed information on the Post Processing features, please refer to
the Post Processing section in the STAAD.Pro Graphical Environment
manual.
Tutorial 1 1-123
1-124
 2-1

Tutorial Problem 2: RC Framed Structure

Section 2
This tutorial provides step-by-step instructions for creating the
model of a reinforced concrete framed structure using STAAD.Pro. The
following topics are covered :

 Starting the Program

 Creating Joints and Members
 Switching On Node and Beam Labels
 Specifying Member Properties and Material Constants
 Specifying Member Orientation using Beta Angle
 Specifying Supports
 Specifying Loads
 Specifying the Analysis Type
 Specifying the parameters and instructions for Concrete Design
 Performing Analysis and Design
 Viewing results using the Output File
 Viewing results on screen – both graphically and numerically
 Producing customized reports
2-2 Tutorial 2

2.1 Methods of creating the model

As explained in Section 1.1 of tutorial problem 1, there are two

methods of creating the structure data:

a) using the graphical model generation mode, or graphical

user interface (GUI) as it is usually referred to.
b) using the command file.

Both methods are explained in this tutorial also. The graphical method
is explained first, from Section 2.2 onwards. Section 2.8
describes the process of creating the model using the command file
method and the STAAD.Pro text editor.
 Tutorial 2 2-3

2.2 Description of the tutorial problem

The structure for this project is a 2 bay, 2 story reinforced concrete

frame. The figure below shows the structure. Our goal is to create
the model, assign all required input, and perform the analysis and
concrete design.

3.5m

6.0m
6.0m

Figure 2. 1
2-4 Tutorial 2

BASIC DATA FOR THE STRUCTURE

ATTRIBUTE DATA

Member properties Beams 2 & 5 : Rectangular, 275 mm width X

350 mm depth

Columns 1 & 4 : Rectangular, 275 mm width X

300 mm depth

Column 3 : Circular, 350 mm diameter

Member Orientation All members except column 4 : Default

Column 4 : Rotated by 90 degrees with respect

to default condition

Material Constants Modulus of Elasticity : 22 KN/sq.mm

Density : 25 kn/cu.m

Poisson's Ratio : 0.17

Supports Base of all columns : Fixed

Loads Load case 1 : Dead Load

Selfweight of the structure.
Beams 2 & 5 : 400 kg/m in global Y downward

Load case 2 : Live Load

Beams 2 & 5 : 600 kg/m in global Y downward
Load case 3 : Wind Load
Beam 1 : 300 kg/m along positive global X
Beam 4 : 500 kg/m along positive global X
Load Case 4 : DEAD + LIVE
L1 X 1.2 + L2 X 1.5 (Use REPEAT LOAD, not
Load Combination)

Load Case 5 : DEAD + WIND

L1 X 1.1 + L2 X 1.3 (Use REPEAT LOAD, not
Load Combination)
 Tutorial 2 2-5

ATTRIBUTE DATA

Analysis Type PDELTA

Concrete Design Consider load cases 4 and 5 only.

Parameters: Ultimate Strength of Steel : 415 N/sq.mm
Concrete Strength : 25 N/sq.mm
Clear cover for top : 25 mm Clear
cover for bottom : 30 mm Clear
cover for side : 25 mm
Design beams 2 and 5
Design columns 1, 3 and 4
2-6 Tutorial 2

2.3 Starting the program

Select the STAAD.Pro icon from the STAAD.Pro 2006 program group.

Figure 2. 2
 Tutorial 2 2-7
The STAAD.Pro Graphical Environment will be invoked and the
following screen comes up.

Figure 2. 3

This New dialog box will come up every time we start the program.
To turn this feature off, simply uncheck the Display this dialog box
at Startup box at the lower left hand corner. This feature can be
turned on again at a later time when File | New is invoked from the
main menu.
2-8 Tutorial 2

Note about the unit system :

There are two base unit systems in the program which control the
units (length, force, temperature, etc.) in which, values,
specifically results and other information presented in the tables and
reports, are displayed in. The base unit system also dictates what type
of default values the program will use when attributes
such as Modulus of Elasticity, Density, etc., are assigned based on
material types – Steel, Concrete, Aluminum – selected from the
program’s library (Please refer to Section 5 of the STAAD.Pro
Technical Reference Manual for details). These two unit systems are
English (Foot, Pound, etc.) and Metric (KN, Meter, etc.).

If you recall, one of the choices made at the time of installing

STAAD.Pro is this base unit system setting. That choice will serve
as the default until we specifically change it.

The place from where we can change this setting is under the File |
Configure menu. To get to that option, first close down the dialog
box shown in the earlier figure by clicking on Cancel. Then, click
on the File | Configure menu option (see figure below) and choose
the appropriate unit system you want. For this tutorial, let us
choose the Metric units (KN, Meter, etc.).

Figure 2. 4
 Tutorial 2 2-9

Figure 2. 5

Click on the Accept button to close the above dialog box.

2-10 Tutorial 2

Following this, select File | New once again.

Figure 2. 6

The dialog box shown in Figure 2.3 will re-appear.

 Tutorial 2 2-11

2.4 Creating a new structure

1. In the New dialog box, we provide some crucial initial data

necessary for building the model.

The structure type is to be defined by choosing from among Space,

Plane, Floor and Truss. A Space type is one where the structure,
the loading or both, cause the structure to deform in all 3 global
axes (X, Y and Z). In a Plane type, the geometry, loading and
deformation are restricted to the global X-Y plane only. A Floor
type is a structure whose geometry is confined to the X-Z plane. A
Truss type of structure carries loading by pure axial action. Truss
members are deemed incapable of carrying shear, bending and
torsion. For our model, let us choose Space.

We choose Meter as the length unit and Kilo Newton as the force unit in
which we will start to build the model. The units can be
changed later if necessary, at any stage of the model creation.

We also need to provide a name in the File Name edit box. This is
the name under which the structure data will be saved on the
computer hard disk. The name “Structure?” (? will be a number) is
recommended by the program by default, but we can change it to
any name we want. Let us choose the name rcframe.

A default path name - the location on the computer drive where the
file will be saved – is provided by the program under Location. If
you wish to save the file in a different location, type in the name,
or click the button and specify the desired path.

After specifying the above input, click on the Next button.

2-12 Tutorial 2

Figure 2. 7

2. In the next dialog box, we choose the tools to be used to initially

construct the model. Add Beams, Add Plates or Add Solids are,
respectively, the starting points for constructing beams, plates or
solids. Open Structure Wizard provides access to a library of
structural templates which the program comes equipped with.
Those template models can be extracted and modified
parametrically to arrive at our model geometry or some of its parts.
If the model is to be created initially using the STAAD command
language, the Open STAAD Editor box can take us to the STAAD
editor. Please remember that all these options are also available
from the menus and dialog boxes of the GUI, even after we dismiss this
dialog box.

Note: If you wish to use the Editor to create the model, choose Open
STAAD Editor, click Finish, and proceed to Section 2.8.
 Tutorial 2 2-13
For our model, let us check the Add Beam option. Click on the
Finish button. The dialog box will be dismissed and the
STAAD.Pro graphical environment will be displayed.

Figure 2. 8
2-14 Tutorial 2

2.5 Elements of the STAAD.Pro screen

The STAAD.Pro main window is the primary screen from where the
model generation process takes place. It is important to
familiarize ourselves with the components of that window before we
embark on creating the RC Frame. Section 1.5 in tutorial
problem 1 of this manual explains the components of that window
in detail.
 Tutorial 2 2-15

2.6 Building the STAAD.Pro model

We are now ready to start building the model geometry. The steps and,
wherever possible, the corresponding STAAD.Pro commands (the
instructions which get written in the STAAD input file) are
described in the following sections.
2-16 Tutorial 2

2.6.1 Generating the model geometry

The structure geometry consists of joint numbers, their

coordinates, member numbers, the member connectivity
information, plate element numbers, etc. From the standpoint of the
STAAD command file, the commands to be generated for the
structure shown in section 2.2 are :

JOINT COORDINATES
1 0.0 0.0 0.0 ; 2 0.0 3.5 0.0
3 6.0 3.5 0.0 ; 4 6.0 0.0 0.0
5 6.0 0.0 6.0 ; 6 6.0 3.5 6.0
MEMBER INCIDENCE
112;223;334;456;536

Steps:

1. We selected the Add Beam option earlier to enable us to add beams

and columns to create the structure. This initiates a grid in the main
drawing area as shown below. The directions of the global axes (X,
Y, Z) are represented in the icon in the lower left hand corner of the
drawing area.

Figure 2. 9
 Tutorial 2 2-17
2. A Snap Node/Beam dialog box also appears in the data area on the
right side of the screen. In our structure, the segment consisting of
members 1 to 3, and nodes 1 to 4, happens to lie in the X-Y plane.
So, in this dialog box, let us keep X-Y as the Plane of the grid. The size of
the model that can be drawn at any time is controlled by the number of
Construction Lines to the left and right of the origin of
axes, and the Spacing between adjacent construction lines. By
setting 12 as the number of lines to the right of the origin along X,
7 above the origin along Y, and a spacing of 0.5 meter between
lines along both X and Y (see figure below) we can draw a frame
6m X 3.5m, adequate for our segment. Please note that these
settings are only a starting grid setting, to enable us to start
drawing the structure, and they do not restrict our overall model to those
limits.

Figure 2. 10
2-18 Tutorial 2

3. To start creating the nodes, let us first activate the Snap

Node/Beam button by clicking on it. Then, with the help of the
mouse, click at the origin (0, 0) to create the first node.

Figure 2. 11

4. In a similar fashion, click on the following points to create nodes

and automatically join successive nodes by beam members.

(0, 3.5), (6, 3.5) and (6, 0)

The exact location of the mouse arrow can be monitored on the

status bar located at the bottom of the window where the X, Y, and
Z coordinates of the current cursor position are continuously
updated.
 Tutorial 2 2-19
When steps 1 to 4 are completed, the frame will be displayed in the
drawing area as shown below.

Figure 2. 12
2-20 Tutorial 2

5. At this point, let us remove the grid display from the structure. To
do that, click on the Close button in the Snap Node/Beam dialog
box.

Figure 2. 13
 Tutorial 2 2-21
The grid will now be removed and the structure in the main
window should resemble the figure shown below.

Figure 2. 14

6. It is very important that we save our work often, to avoid loss of

data and protect our investment of time and effort against power
interruptions, system problems, or other unforeseen events. To save the file,
pull down the File menu and select the Save command.
2-22 Tutorial 2

Switching on node and beam labels

7. Node and beam labels are a way of identifying the entities we have
drawn on the screen. In order to display the node and beam
numbers, right click anywhere in the drawing area. In the pop-up
menu that appears, choose Labels. Alternatively, one may access
this option by selecting the View menu followed by the Structure
Diagrams option from the top menu bar, and the Labels tab of the
dialog box that comes up.

Figure 2. 15
 Tutorial 2 2-23
8. In the Diagrams dialog box that appears, turn the Node Numbers
and Beam Numbers on and then click on OK.

Figure 2. 16
2-24 Tutorial 2

The following figure illustrates the node and beam numbers

displayed on the structure. The structure in the main window should
resemble the figure shown below.

Figure 2. 17

If you are feeling adventurous, here is a small exercise for you. Change the
font of the node/beam labels by going to the View menu and selecting the
Options command, and then selecting the
appropriate tab (Node Labels / Beam labels) from the Options
dialog box.
 Tutorial 2 2-25
9. Examining the structure shown in section 2.2 of this tutorial, it can
be seen that members 4 and 5 can be easily generated if we could
first create a copy of members 1 and 2 and then rotate those copied units
about a vertical line passing through the point (6, 0, 0, that is, node 4) by 90
degrees. Fortunately, such a facility does exist which can be executed in a
single step. It is called Circular Repeat and is available under the Geometry
menu.

First, select members 1 and 2 using the Beams Cursor . (Please

refer to the ‘Frequently Performed Tasks’ section at the end of this
manual to learn more about selecting members.)

10. Then, either click on the Circular Repeat icon from the appropriate
toolbar, or, go to the Geometry | Circular Repeat menu option as
shown below.

Figure 2. 18
2-26 Tutorial 2

11. In the 3D Circular dialog box that comes up, specify the Axis of
Rotation as Y, Total Angle as 90 degrees, No. of Steps as 1 and the vertical
line as passing through Node 4. Instead of specifying as
passing through Node 4, one may also specify the X and Z co-
ordinates as 6 and 0 respectively. Leave the Link Steps box
unchecked and click on the OK button.

Figure 2. 19
 Tutorial 2 2-27
After completing the circular repeat procedure, the model will look
as shown below.
Before

Figure 2. 20

After

Figure 2. 21

If any of the members are presently selected, let us unselect them by

clicking anywhere else in the drawing area. Then, let us once again save
the work by pulling down the File menu and selecting the Save
command.
2-28 Tutorial 2

2.6.2 Changing the input units of length

As a matter of convenience, for specifying member properties for

our structure, it is simpler if our length units are millimeter instead
of meter. This will require changing the current length units of
input. The commands to be generated are:

UNIT MMS KN

Steps:

1. Click on the Input Units icon from the appropriate toolbar.

Figure 2. 22

Alternatively, one may select the Tools | Set Current Input Unit
menu option as shown in the next figure.
 Tutorial 2 2-29

Figure 2. 23

2. In either case, the following dialog box comes up. Set the Length
Units to Millimeter and click on the OK button.

Figure 2. 24
2-30 Tutorial 2

2.6.3 Specifying member properties

Our next task is to assign cross section properties for the beams
and columns (see section 2.2). For those of us curious to know the
equivalent commands in the STAAD command file, they are :

MEMB PROP
1 4 PRIS YD 300 ZD 275
2 5 PRIS YD 350 ZD 275
3 PRIS YD 350

Steps:

1. Click on the Property Page icon located on the Structure Tools

toolbar.

Figure 2. 25
 Tutorial 2 2-31
Alternatively, one may go to the General | Property page from the left
side of the screen as shown below.

Figure 2. 26
2-32 Tutorial 2

2. In either case, the Properties dialog box comes up. The property
type we wish to assign is called PRISMATIC, and is available
under the Define button in the Properties dialog box as shown below.

Figure 2. 27

3. In the dialog box that comes up, select the Rectangle tab. Notice
that the field called Material is presently on the checked mode. If
we keep it that way, the material properties of concrete (E,
Poisson, Density, Alpha, etc.) will be assigned along with the
cross-section name. The material property values so assigned will
be the program defaults. We do not want default values, instead we
will assign our own values later on. Consequently, let us uncheck
the Material box. Then, enter the following values:

YD = 300mm ZD = 275mm
 Tutorial 2 2-33
Finally, click on the Add button as shown below.

Figure 2. 28

4. To create the second member property (PRIS YD 350 ZD 275),

provide 350 for YD and 275 for ZD (instead of 300 and 275) and
click on the Add button.

To create the third member property, in the Property dialog box, select
the Circle option. Specify the diameter (YD) as 350 mm.
Once again, uncheck the Material box and click on the Add
button.

Figure 2. 29

Now that we have finished creating the member properties, let us

Close this dialog box.
2-34 Tutorial 2

The next step is to assign these member properties in the following

manner:

Rect 0.30x0.28 – members 1 and 4

Rect 0.35x0.28 – members 2 and 5 Cir
0.35 – member 3

To assign the member properties, follow these steps:

a. Select the first property reference in the Properties dialog

box (Rect 0.30x28).
b. Make sure that the “Use Cursor to Assign” button is
selected under the Assignment Method box.

c. Click on the Assign button. The cursor changes to

d. Using the cursor, click on members 1 and 4.
e. Finally, click on the Assign button again, or type the ‘Esc’
button on your keyboard to stop the assignment process.

Figure 2. 30

In a similar fashion, assign the remaining properties.

 Tutorial 2 2-35
After all the member properties have been assigned, the model will look as
shown below.

Figure 2. 31

We ought to save the model once again by pulling down the File
menu and selecting the Save command.
2-36 Tutorial 2

2.6.4 Specifying geometric constants

In the absence of any explicit instructions, STAAD will orient the beams
and columns of the structure in a pre-defined way.
Orientation refers to the directions along which the width and depth of
the cross section are aligned with respect to the global axis system.
The rules which dictate this default orientation are explained in
Section 1 of the STAAD.Pro Technical Reference Manual.

We wish to orient member 4 so that its longer edges (sides parallel

to local Y axis) are parallel to the global Z axis. This requires
applying a beta angle of 90 degrees. The command which needs to
be generated is :

BETA 90 MEMB 4

Steps:

1. Select the Beta Angle tab in the Properties dialog box.

2. Click on the Create Beta Angle button. In the ensuing dialog box,
specify the angle as 90 degrees. Select member 4 using the Beams
Cursor .

Notice that as we select the member, the Assignment Method

automatically sets to Assign to Selected Beams. Click on the Assign
button.

Click anywhere in the drawing area to un-highlight the member.

 Tutorial 2 2-37

Figure 2. 32

(An alternative method to assign beta angles is the following. First

select the member for which you wish to assign the beta angle.
Then, go to the Commands | Geometric Constants | Beta Angle
menu option. Specify the Angle in Degrees to be 90, ensure that the
assignment method is “To Selection” and click on OK. )

Figure 2. 33

One may view the orientation of the member local axes by going to
the View | Structure diagrams | Labels menu option and switching
on Beam Orientation.
2-38 Tutorial 2

2.6.5 Specifying material constants

At the time of assigning member properties, we deliberately chose not to

assign the material constants simultaneously, since we
wanted to specify values which are different from the built-in
defaults. The desired values are listed at the beginning of this
tutorial. The corresponding commands we wish to generate in the
STAAD input file are:

CONSTANTS
E 22 ALL
UNIT METER
DENSITY 25.0 ALL
POISSON 0.17 ALL

Steps:

1. From the Commands menu, select Material Constants. To define

the Modulus of Elasticity, select the Elasticity option as shown
below.

Figure 2. 34
 Tutorial 2 2-39
2. In the Material Constant dialog box that appears, enter 22 in the
Enter Value box. Since the value has to be assigned to all the
members of the structure, the current setting of the assignment
method, namely, To View, allows us to achieve this easily. Then,
click on OK.

Figure 2. 35

3. For specifying the DENSITY constant, it will be convenient if we

change our length units to meters. To change the length units, as

before, click on the Input Units icon from the Structure

toolbar, or select the Tools | Set Current Input Unit menu option from
the top menu bar. In the Set Current Input Units dialog box that comes
up, specify the length units as Meter.

Figure 2. 36
2-40 Tutorial 2

4. Following the steps 1 and 2 above, we choose Commands |

Material Constants | Density, specify the value as 25KN/m3, and assign
To View.

5. To define the POISSON’S RATIO, using the similar procedure as

described above, provide the value 0.17 to all members in the
View.
 Tutorial 2 2-41

2.6.6 Specifying Supports

The base nodes of all the columns are restrained against translation and
rotation about all the 3 global axes (see section 2.2). In other words, fixed
supports are to be specified at those nodes. The
commands to be generated are :

SUPPORTS
1 4 5 FIXED

Steps:

1. To create supports, click on the Support Page icon located in the

Structure Tools toolbar as shown below.

Figure 2. 37
2-42 Tutorial 2

Alternatively, one may go to the General | Support Page from the

left side of the screen.

Figure 2. 38
 Tutorial 2 2-43
2. In either case, the Supports dialog box comes up. Since we already
know that nodes 1, 4 and 5 are to be associated with the Fixed
support, using the Nodes Cursor , select these nodes.

3. Then, click on the Create button in the Supports dialog box as

shown below.

Figure 2. 39
2-44 Tutorial 2

4. The Create Support dialog box comes up. In the dialog box, the
Fixed tab happens to be the default which is convenient for this
case. Click on the Assign button as shown below.

Figure 2. 40
 Tutorial 2 2-45
After the supports have been assigned, the structure will look like the one
shown below.

Figure 2. 41

Click anywhere in the drawing area to un-select all selected nodes

and prevent accidental assignment of unwanted data to those nodes.

As earlier, save the work completed so far by going to the File

menu and clicking on the Save command.
2-46 Tutorial 2

2.6.7 Specifying Loads

5 load cases are to be created for this structure. Details of the

individual cases are explained at the beginning of this tutorial. The
corresponding commands to be generated are listed below. Notice that
cases 4 and 5 are to be generated not as the standard
combination type, but using a combination load type called
REPEAT LOAD. The instructions at the beginning of this tutorial require
us to analyze this structure using an analysis type called
PDelta. A Pdelta analysis is a non-linear type of analysis. In
STAAD, to accurately account for the PDelta effects arising from
the simultaneous action of previously defined horizontal and
vertical loads, those previous cases must be included as
components of the combination case using the REPEAT LOAD type.

UNIT METER KG

LOAD 1 DEAD LOAD

SELFWEIGHT Y -1
MEMBER LOAD
2 5 UNI GY -400

LOAD 2 LIVE LOAD

MEMBER LOAD
2 5 UNI GY -600

LOAD 3 WIND LOAD

MEMBER LOAD
1 UNI GX 300
4 UNI GX 500

LOAD 4 DEAD + LIVE

REPEAT LOAD
1 1.2 2 1.5
 Tutorial 2 2-47
LOAD 5 DEAD + WIND
REPEAT LOAD
1 1.1 3 1.3

Steps:

LOAD CASE 1

1. To create loads, click on the Load Page icon located on the

Structure Tools tool bar.

Figure 2. 42

Alternatively, one may go to the General | Load Page from the left side of
the screen.

Figure 2. 43
2-48 Tutorial 2

2. A window titled “Load” appears on the right-hand side of the

screen. To initiate the first load case, highlight the Load Cases Details
option and click on the Add button.

Figure 2. 44

3. The Add New Load Cases dialog box comes up. The drop-down list
box against Loading Type is available in case we wish to associate
the load case we are creating with any of the ACI, AISC or IBC
definitions of Dead, Live, Ice, etc. This type of association needs
to be done if we intend to use the program's facility for
automatically generating load combinations in accordance with those
codes.

Notice that there is a check box called Reducible per UBC/IBC.

This feature becomes active only when the load case is assigned a
Loading Type called Live at the time of creation of that case.
Please refer to STAAD.Pro 2004 Release Report for further details.

As we do not intend to use the automatic load combination

generation option, we will leave the Loading Type as None. Enter
DEAD LOAD as the Title for Load Case 1 and click on Add.
 Tutorial 2 2-49

Figure 2. 45

The newly created load case will now appear under the Load Cases Details
option.

Figure 2. 46
2-50 Tutorial 2

4. To generate and assign the selfweight load type, first highlight

DEAD LOAD. You will notice that the Add New Load Items dialog box
shows more options now.

Figure 2. 47

5. In the Add New Load Items dialog box, select the Selfweight Load
option under the Selfweight item. Specify the Direction as Y, and the
Factor as -1.0. The negative number signifies that the
selfweight load acts opposite to the positive direction of the global axis (Y
in this case) along which it is applied. Click on the Add button. The
selfweight load is applicable to every member of the
structure, and cannot be applied on a selected list of members.

Figure 2. 48
 Tutorial 2 2-51
6. Load 1 contains an additional load component, the member loads
on members 2 and 5. However, notice that the load values are
listed in the beginning of this tutorial in kg and meter units. Rather than
convert those values to the current input units, we will
conform to those units. The current input units, which we last set
while specifying Density, are KN and METER. We have to change
the force unit to Kilogram.

STAAD has a limitation in that one cannot change the units while editing
load cases. If we attempt to, the following message will be displayed.

Figure 2. 49

Click on OK. Close the Add New Load Items dialog box. Then, go
to the Setup Page as shown below (or any other page).

Figure 2. 50
2-52 Tutorial 2

As before, click on the Input Units icon from the top toolbar,
or select the Tools | Set Current Input Unit menu option from the
top menu bar. In the Set Current Input Units dialog box that comes
up, specify the force units as Kilogram. Again, click on General |
Load page to resume creating the load cases.

7. To create the member load, first, click on the expression DEAD

LOAD followed by the Add button. Then, click on the Member
Load item in the Add New Load Items dialog box.

Figure 2. 51

8. Select the Uniform Force option and specify GY as the Direction

and -400 as the Force. For these members, since the local Y axis
coincides with the global Y axis, one may choose the direction of
the load as either “Y” or “GY”, they will both have the same
effect. (One may view the orientation of the member local axes by going
to View | Structure Diagrams | Labels | Beam Orientation.) The negative
value signifies that the load acts along the negative
GY direction. Then, click on the Add button followed by the Close
button.
 Tutorial 2 2-53
9. The member load we just created has to be assigned to members 2
and 5. First, make sure that the expression UNI GY -400Kg/m is
selected in the Load dialog box as shown below.

Figure 2. 52

10. Next, select members 2 and 5 using the Beams Cursor .

(Please refer to the ‘Frequently Performed Tasks’ section at the end of
this manual to learn more about selecting members.)

Then, click on Assign to Selected Beams followed by the Assign

button.

Figure 2. 53

As we click on the Assign button, the following dialog box

appears. This message box appears just to confirm that we indeed wish to
associate the loadcase with the selected beams. So, let us choose Yes.

Figure 2. 54
2-54 Tutorial 2

After the load has been assigned, the structure will look as shown below:

Figure 2. 55
 Tutorial 2 2-55
LOAD CASE 2

11. The next step is to initiate the second load case which again
contains MEMBER LOADs. Highlight Load Cases Details and click
on the Add button. Once again, the Add New Load Cases dialog box
comes up.

Figure 2. 56

In this dialog box, once again, we are not associating the load case
we are about to create with any code based Loading Type and so,
we will leave that box as None. Specify the Title of the second
load case as LIVE LOAD and click on the Add button.

Figure 2. 57
2-56 Tutorial 2

12. To create the member load, highlight LIVE LOAD as shown

below.

Figure 2. 58

13. Follow steps 7 to 10 to create and assign a uniformly distributed

force of -600Kg/m on members 2 and 5.

After the second load case has been assigned, the structure will look as
shown below:

Figure 2. 59

Click anywhere in the drawing area to un-highlight the members.

 Tutorial 2 2-57
LOAD CASE 3

14. Creating the third load case, which again has MEMBER LOADs,
involves the same procedure as that for load case 2. As before, first
highlight Load Cases Details in the Load dialog box to initiate the third
load case. Enter WIND LOAD as the Title for Load Case 3.

15. To apply the load on member 1, follow the procedure similar to

that in steps 7 to 10. The only differences are, the member which
receives this load is 1, the Direction is GX and the Force is
+300Kg/m.

16. Similarly, for member 4 and the third load case, specify the Force
as 500Kg/m and the Direction as GX.

After the third load case has been assigned, the structure will look
as shown below:

Figure 2. 60
2-58 Tutorial 2

LOAD CASE 4

17. We now come to the point where we have to create load case 4 as
(1.2 x Load 1) + (1.5 x Load 2). We saw in the beginning of this
section that we should be creating a “REPEAT LOAD” type of
combination, and not the “LOAD COMBINATION” type. To initiate
load case 4, highlight Load Cases Details in the Load dialog box
and specify the title as DEAD + LIVE.

18. Then, click on DEAD + LIVE in the Load dialog box as shown
below.

Figure 2. 61

19. In the Add New Load Items dialog box, click on the Repeat Load
option. Then, select Load Case 1 (DEAD LOAD), click on the
button and enter the Factor as 1.2. (This indicates that the load
data values from load case 1 are multiplied by a factor of 1.2, and
the resulting values are utilized in load case 4.)

20. Similarly, select Load Case 2 (LIVE LOAD), click on the

button and enter the Factor as 1.5.
 Tutorial 2 2-59
The Add New Load Items dialog box will now look as shown
below. Click on the Add button.

Figure 2. 62

No further operation is required for load case 4. The recipients

(members) of the loads in load case 4 are automatically chosen to
be the very same ones to which the components of the REPEAT
LOAD cases (loads 1 and 2) were assigned.
2-60 Tutorial 2

The structure will now look similar to the one shown below.

Figure 2. 63
 Tutorial 2 2-61
LOAD CASE 5

21. Since load cases 4 and 5 are near identical in nature, the same
procedure used in creating load case 4 is applicable for case 5 also.
Let us highlight Load Cases Details in the Load dialog box to
initiate the fifth load case. Enter DEAD + WIND as the Title for
Load Case 5.

22. Follow steps 18 to 20 except for associating a Factor of 1.1 with

the first load case and a Factor of 1.3 with the third load case.

The Add New Load Items dialog box will now look as shown
below. Click on the Add button.

Figure 2. 64

Since we have completed creating all the load cases, we may now
click on the Close button to dismiss the Add New Load Items
dialog box.
2-62 Tutorial 2

The structure will now look similar to the one shown below.

Figure 2. 65

Let us save the work completed so far by going to the File menu
and selecting the Save command or by holding the ‘Ctrl’ key and
pressing the ‘S’ key.
 Tutorial 2 2-63

2.6.8 Specifying the analysis type

The analysis type for this structure is called P-Delta. Since this problem
involves concrete beam and column design per the ACI code, second-
order analysis is required and has to be done on
factored loads acting simultaneously. The factored loads have been created
earlier as cases 4 and 5. Now is the time to specify the
analysis type.

The command for a pdelta analysis will appear in the STAAD file as:

PDELTA ANALYSIS

Steps:

1. Go to Analysis/Print Page on the left side of the screen.

Figure 2. 66
2-64 Tutorial 2

2. In the Analysis/Print Commands dialog box that appears, select the

PDelta Analysis tab. Then, click on the Add button followed by the
Close button.

Figure 2. 67

Save the work again using the Save option of the File menu.
 Tutorial 2 2-65

2.6.9 Short-listing the load cases to be used

in concrete design

The concrete design has to be performed for load cases 4 and 5 only
since only those are the factored cases. To instruct the
program to use just these cases, and ignore the remaining, we have
to use the LOAD LIST command.

The command will appear in the STAAD file as :

LOAD LIST 4 5

Steps:

1. In the menus on the top of the screen, go to Commands | Loading

| Load List option as shown below.

Figure 2. 68
2-66 Tutorial 2

2. In the Load List dialog box that comes up, select load cases 4
(DEAD + LIVE) and 5 (DEAD + WIND) by holding the ‘Ctrl’ key
down. Then, click on the button. Load cases 4 and 5 will be
selected and placed in the Load List selection box as shown below. Click
on the OK button.

Figure 2. 69
 Tutorial 2 2-67

2.6.10 Specifying concrete design parameters

Among the various terms which appear in the equations for design
of concrete beams and columns, some of them can be user
controlled, such as, the grade of concrete, or the maximum size of
reinforcing bar one may wish to use. Such terms are called
concrete design parameters. For the ACI code, a list of these
parameters is available in Section 3 of the STAAD.Pro Technical
Reference Manual. The parameters we wish to use, and the
corresponding command which ought to appear in the STAAD input
file are :

UNIT MMS NEWTON

CODE ACI
CLT 25 ALL
CLB 30 ALL
CLS 25 ALL
FC 25 ALL
FYMAIN 415 ALL
TRACK 1 ALL

Steps:

1. Before we can start assigning the parameters, we want our force

units to be Newton and our length units to be millimeter. We last
set the units during load specification as Kg and Meter. To change

the units, as before, click on the Input Units icon from the
appropriate toolbar, or select the Tools | Set Current Input Unit
menu option from the top menu bar. In the Set Current Input Units
dialog box that comes up, specify the force units as Newton and
the length units as Millimeter.

2. Next, go to Design | Concrete Page from the left side of the

screen. Make sure that under the Current Code selections on the top
right hand side, ACI is selected. Then, click on the Define Parameters
button in the Concrete Design dialog box.
2-68 Tutorial 2

Figure 2. 70

3. In the Design Parameters dialog box that opens, select the Clt
(Clear Cover for top) tab. Then, provide the value as 25mm and click
on the Add button as shown below.

Figure 2. 71
 Tutorial 2 2-69
4. To define the remaining parameters, follow the above procedure
and provide the following values.

Parameter Value

Clb 30
Cls 25
Fc 25
Fymain 415
Track 1.0

When all the above parameters have been assigned, click on the
Close button in the Design Parameters dialog box.

After all the design parameters have been assigned, the Concrete Design
dialog box will look as shown below.

Figure 2. 72
2-70 Tutorial 2

The next step is to assign these parameters to all the members in

our model. The easiest way to do that is to use the Assign To View
method. Follow the steps as shown in the figure below.

Figure 2. 73

Let us save our structure once again using the Save option of the
File menu.
 Tutorial 2 2-71

2.6.11 Specifying design commands

Design commands are the actual instructions for the design of beams
and columns. We intend to design beams 2 and 5 and
columns 1, 3 and 4. The commands to be generated are :

DESIGN BEAM 2 5
DESIGN COLUMN 1 3 4

Steps:

1. Design commands are generated through the dialog boxes available

under the Commands button in the Concrete Design dialog box. So,
let us click on the Commands button as shown below.

Figure 2. 74
2-72 Tutorial 2

2. In the Design Commands dialog box that comes up, select the
DESIGN BEAM option and click on the Add button.

Figure 2. 75

3. We also need to add a command for designing columns. So, select

the DESIGN COLUMN option and click on Add button.

After steps 2 and 3 are completed, let us Close this dialog box.

4. The next step is to associate the Design Beam command with

members 2 and 5 and the Design Column command with members
1, 3 and 4.

To do this, as before, first highlight the expression DESIGN

BEAM. Then, select members 2 and 5 using the Beams Cursor
. Click on Assign to Selected Beams followed by the Assign
button.

Figure 2. 76
 Tutorial 2 2-73
As we click on the Assign button, the following dialog box
appears. This message box appears just to confirm that we indeed wish to
associate the design command with the selected beams. So, let us say Yes.

Figure 2. 77

Similarly, assign the Design Column command to members 1, 3 and 4

This concludes the task of assigning all the input for our model. Let us
Save the file one final time.
2-74 Tutorial 2

2.7 Viewing the input command file

Let us now take a look at the data that has been written into the file that we
just saved above. The contents of the file can be viewed
either by clicking on the STAAD Editor icon or, by going to the
Edit menu and choosing Edit Input Command File as shown below.

Figure 2. 78
 Tutorial 2 2-75
A new window will open up with the data listed as shown here:

Figure 2. 79

This window and the facilities it contains is known as the STAAD Editor.
2-76 Tutorial 2

We could make modifications to the data of our structure in this

Editor if we wish to do so. Let us Exit the Editor without doing so
by selecting the File | Exit menu option of the editor window (not
the File | Exit menu of the main window behind the editor
window).

As we saw in Section 2.1, we could also have created the same model
by typing the relevant STAAD commands into a text file
using either the STAAD editor, or by using any external editor of our
choice. If you would like to understand that method, proceed
to the next section. If you want to skip that part, proceed to section
2.9 where we perform the analysis and design on this model.
 Tutorial 2 2-77

2.8 Creating the model using the command file

Let us now use the command file method to create the model for
the above structure. The commands used in the command file are
described later in this section.

The STAAD.Pro command file may be created using the built-in editor,
the procedure for which is explained further below in this
section. Any standard text editor such as Notepad or WordPad may also be
used to create the command file. However, the STAAD.Pro command file
editor offers the advantage of syntax checking as we type the commands.
The STAAD.Pro keywords, numeric data,
comments, etc. are displayed in distinct colors in the STAAD.Pro
editor. A typical editor screen is shown below to illustrate its general
appearance.

Figure 2. 80
2-78 Tutorial 2

To access the built-in editor, first start the program using the
procedure explained in Section 2.2. Next, follow step 1 of Section 2.4.

Figure 2. 81

You will then encounter the dialog box shown below. In this dialog
box, choose Open STAAD Editor.

Figure 2. 82
 Tutorial 2 2-79
At this point, the editor screen will open as shown below.

Figure 2. 83

Delete all the command lines displayed in the editor window and
type the lines shown in bold below (You don’t have to delete the
lines if you know which to keep and where to fill in the rest of the
commands). The commands may be typed in upper or lower case
letters. Usually the first three letters of a keyword are all that are needed
-- the rest of the letters of the word are not required. The required letters
are underlined. (“SPACE” = “SPA” = “space” = “spa”)
2-80 Tutorial 2

Actual input is shown in bold lettering followed by explanation.

STAAD SPACE RC FRAMED STRUCTURE

Every input has to start with the word STAAD. The word SPACE
signifies that the structure is a space frame structure (3-D) and the
geometry is defined through X, Y and Z coordinates.

UNIT METER KN

Specifies the unit to be used.

JOINT COORDINATES
1 0 0 0 ; 2 0 3.5 0 ; 3 6 3.5 0
4 6 0 0 ; 5 6 0 6 ; 6 6 3.5 6

Joint number followed by X, Y and Z coordinates are provided

above. Semicolon signs (;) are used as line separators. That enables
us to provide multiple sets of data on one line.

MEMBER INCIDENCES 1
12;223;334
456;563

Defines the members by the joints they are connected to.

UNIT MMS KN
MEMBER PROPERTY AMERICAN 1
4 PRIS YD 300 ZD 275
2 5 PRIS YD 350 ZD 275
3 PRIS YD 350

Member properties have been defined above using the PRISMATIC

attribute for which YD (depth) and ZD (width) values are provided
in MM unit. When YD and ZD are provided together, STAAD
considers the section to be rectangular. When YD alone is
specified, the section is considered to be circular. Details are
available in Section 5 of the Technical Reference Manual.
 Tutorial 2 2-81
CONSTANTS
E 22 MEMB 1 TO 5

Material constant E (modulus of elasticity) is specified as

22KN/sq.mm following the command CONSTANTS.

UNIT METER KN
CONSTANTS
DENSITY 25.0 ALL
POISSON 0.17 ALL

Length unit is changed from MMS to METER to facilitate the input

of Density. Next, the Poisson’s Ratio is specified.

BETA 90 MEMB 4

In the absence of any explicit instructions, STAAD will orient the beams
and columns of the structure in a pre-defined way (see
Section 1 of the Technical Reference Manual for details.) In order
to orient member 4 so that its longer edges (sides parallel to local
Y axis) are parallel to the global Z axis, we need to apply a beta
angle of 90 degrees.

SUPPORT
1 4 5 FIXED

Joints 1, 4 and 5 are defined as fixed supported.

UNIT METER KG
LOAD 1 DEAD LOAD

Force units are changed from KN to KG to facilitate the input of loads.

Load case 1 is initiated along with an accompanying title.
2-82 Tutorial 2
SELFWEIGHT Y -1

One of the components of load case 1 is the selfweight of the

structure acting in the global Y direction with a factor of -1.0.
Since global Y is vertically upward, the factor of -1.0 indicates that
this load will act downwards.

MEMBER LOAD
2 5 UNI GY -400

Load 1 contains member loads also. GY indicates that the load is in the
global Y direction. The word UNI stands for uniformly
distributed load. Loads are applied on members 2 and 5.

LOAD 2 LIVE LOAD

Load case 2 is initiated along with an accompanying title.

MEMBER LOAD
2 5 UNI GY -600

Load 2 also contains member loads. GY indicates that the load is in the
global Y direction. The word UNI stands for uniformly
distributed load. Loads are applied on members 2 and 5.

LOAD 3 WIND LOAD

Load case 3 is initiated along with an accompanying title.

MEMBER LOAD
1 UNI GX 300
4 UNI GX 500

Load 3 also contains member loads. GX indicates that the load is in the
global X direction. The word UNI stands for uniformly
distributed load. Loads are applied on members 1 and 4.

LOAD 4 DEAD + LIVE

Load case 4 is initiated along with an accompanying title.

 Tutorial 2 2-83
REPEAT LOAD
1 1.2 2 1.5

Load case 4 illustrates the technique employed to instruct STAAD

to create a load case which consists of data to be assembled from
other load cases specified earlier. We are instructing the program
to analyze the structure for loads from cases 1 and 2 acting
simultaneously. The load data values from load case 1 are
multiplied by a factor of 1.2, and the resulting values are utilized
in load case 4. Similarly, the load data values from load case 2 are
multiplied by a factor of 1.5, and the resulting values too are
utilized in load case 4.

LOAD 5 DEAD + WIND

Load case 5 is initiated along with an accompanying title.

REPEAT LOAD
1 1.1 3 1.3

We are instructing the program to analyze the structure for loads from
cases 1 and 3 acting simultaneously.

PDELTA ANALYSIS

The PDELTA ANALYSIS command is an instruction to the

program to execute a second-order analysis and account for P-delta effects.

LOAD LIST 4 5

The above LOAD LIST command is a means of stating that all

further calculations should be based on the results of load cases 4 and 5
only. The intent here is to restrict concrete design
calculations to that for load cases 4 and 5 only.
2-84 Tutorial 2
START CONCRETE DESIGN
CODE ACI
UNIT MMS NEWTON
CLT 25 ALL
CLB 30 ALL
CLS 25 ALL
FC 25 ALL
FYMAIN 415 ALL
TRACK 1 ALL

We first line is the command that initiates the concrete design

operation. The values for the concrete design parameters are
defined in the above commands. Design is performed per the ACI Code.
The length units are changed from METER to MMS to
facilitate the input of the design parameters. Similarly, force units
are changed from KG to NEWTON. The TRACK value dictates the
extent of design related information which should be produced by
the program in the output. The parameters specified include
CLT(Clear cover for top surface), CLB (Clear cover for bottom
surface), CLS (Clear cover for sides), FC(Strength of concrete), and
FYMAIN(Ultimate strength of steel). These parameters are described
in Section 3 of the Technical Reference Manual.

DESIGN BEAM 2 5
DESIGN COLUMN 1 3 4

The above commands instruct the program to design beams 2 and 5

for flexure, shear and torsion, and to design columns 1, 3 and 4 for
axial load and biaxial bending.

END CONCRETE DESIGN

This command terminates the concrete design operation.

FINISH

This command terminates the STAAD run. Let

us save the file and exit the editor.

 Tutorial 2 2-85

2.9 Performing the analysis and design

STAAD.Pro performs Analysis and Design simultaneously. In order

to perform Analysis and Design, select the Run Analysis option from
the Analyze menu.

Figure 2. 84

If the structure has not been saved after the last change was made, you
should save the structure first by using the Save command
from the File menu.

When you select the Run Analysis option from the Analyze menu, the
following dialog box appears:

Figure 2. 85

We are presented with the choice of 2 engines : the STAAD engine and the
STARDYNE Advanced Analysis engine. The STARDYNE Analysis
engine is suitable for advanced problems such as
Buckling Analysis, Modal Extraction using various methods, etc.
However, if the calculations call for steel or concrete design, UBC
load generation, etc., we have to select the STAAD engine. So, let
us ensure that the radio button is on the STAAD engine.
2-86 Tutorial 2

Click on the Run Analysis button.

As the Analysis progresses, several messages appear on the screen

as shown in the next figure.

Figure 2. 86
Notice that we can choose from the three options available in the above
dialog box :

Figure 2. 87

These options are indicative of what will happen after we click on the
Done button.
 Tutorial 2 2-87
The View Output File option allows us to view the output file
created by STAAD. The output file contains the numerical results
produced in response to the various input commands we specified during
the model generation process. It also tells us whether any
errors were encountered, and if so, whether the analysis and design
was successfully completed or not. Section 2.10 offers additional
details on viewing and understanding the contents of the output
file.

The Go to Post Processing Mode option allows us to go to

graphical part of the program known as the Post-processor. This is where
one can extensively verify the results, view the results
graphically, plot result diagrams, produce reports, etc. Section 2.11
explains the post processing mode in greater detail.

The Stay in Modelling Mode lets us continue to be in the Model

generation mode of the program (the one we current are in) in case we
wish to make further changes to our model.
2-88 Tutorial 2

2.10 Viewing the output file

During the analysis process, STAAD.Pro creates an Output file.

This file provides important information on whether the analysis
was performed properly. For example, if STAAD.Pro encounters an
instability problem during the analysis process, it will be reported
in the output file.

We can access the output file using the method explained at the
end of the previous section. Alternatively, we can select the File | View |
Output File | STAAD Output option from the top menu.
The STAAD.Pro output file for the problem we just ran is shown in the
next few pages.

Figure 2. 88
 Tutorial 2 2-89
The STAAD.Pro output file is displayed through a file viewer
called SproView. This viewer allows us to set the text font for the
entire file and print the output file to a printer. Use the appropriate
File menu option from the menu bar.

Figure 2. 89

By default, the output file contains a listing of the entire input also. You
may choose not to print the echo of the input commands in the output file.
Please select Commands | Miscellaneous | Set Echo
option from the menu bar and select the Echo Off button.

It is quite important that we browse through the entire output file

and make sure that the results look reasonable, that there are no
error messages or warnings reported, etc. Errors encountered
during the analysis & design can disable access to the post-
processing mode – the graphical screens where results can be
viewed graphically. The information presented in the output file is
a crucial indicator of whether or not the structure satisfies the
engineering requirements of safety and serviceability.
2-90 Tutorial 2

****************************************************
* *
* STAAD.Pro *
* Version Bld *
* Proprietary Program of *
* Research Engineers, Intl. *
* Date= *
* Time= *
* *
* USER ID: *
****************************************************

1. STAAD SPACE RC FRAMED STRUCTURE

2. START JOB INFORMATION
3. ENGINEER DATE
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 2 0 3.5 0; 3 6 3.5 0; 4 6 0 0; 5 6 0 6; 6 6 3.5 6
9. MEMBER INCIDENCES
10. 1 1 2; 2 2 3; 3 3 4; 4 5 6; 5 6 3
11. UNIT MMS KN
12. MEMBER PROPERTY AMERICAN
13. 1 4 PRIS YD 300 ZD 275
14. 2 5 PRIS YD 350 ZD 275
15. 3 PRIS YD 350
16. CONSTANTS
17. E 22 MEMB 1 TO 5
18. UNIT METER KN
19. CONSTANTS
20. DENSITY 25.0 ALL
21. POISSON 0.17 ALL
22. BETA 90 MEMB 4
23. SUPPORTS
24. 1 4 5 FIXED
25. UNIT METER KG
26. LOAD 1 DEAD LOAD
27. SELFWEIGHT Y -1
28. MEMBER LOAD
29. 2 5 UNI GY -400
30. LOAD 2 LIVE LOAD
31. MEMBER LOAD
32. 2 5 UNI GY -600
33. LOAD 3 WIND LOAD
34. MEMBER LOAD
35. 1 UNI GX 300
36. 4 UNI GX 500
37. LOAD 4 DEAD + LIVE
38. REPEAT LOAD
39. 1 1.2 2 1.5
40. LOAD 5 DEAD + WIND
41. REPEAT LOAD
42. 1 1.1 3 1.3
43. PDELTA ANALYSIS

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS/MEMBER+ELEMENTS/SUPPORTS = 6/ 5/ 3
ORIGINAL/FINAL BAND-WIDTH= 3/ 3/ 12 DOF
TOTAL PRIMARY LOAD CASES = 5, TOTAL DEGREES OF FREEDOM = 18
SIZE OF STIFFNESS MATRIX = 1 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.0/ 43064.0 MB
 Tutorial 2 2-91

44. LOAD LIST 4 5

45. START CONCRETE DESIGN
46. CODE ACI
47. UNIT MMS NEWTON
48. CLT 25 MEMB 1 TO 5
49. CLB 30 MEMB 1 TO 5
50. CLS 25 ALL
51. FC 25 MEMB 1 TO 5
52. FYMAIN 415 MEMB 1 TO 5
53. TRACK 1 ALL
54. DESIGN BEAM 2 5

=====================================================================

BEAM NO. 2 DESIGN RESULTS - FLEXURE PER CODE ACI 318-02

LEN - 6000. MM FY - 415. FC - 25. MPA, SIZE - 275. X 350. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END

1 51. 2 - 16MM 313. 5437. NO NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 39.16 KN-MET AT 3000.MM, LOAD 4|
| REQD STEEL= 366.MM2, ROW=0.0044, ROWMX=0.0193 ROWMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 273./ 41./ 184. MMS |
| REQD. DEVELOPMENT LENGTH = 480. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 20964.0 cm^4

2 306. 3 - 12MM 0. 860. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 33.29 KN-MET AT 0.MM, LOAD 4|
| REQD STEEL= 301.MM2, ROW=0.0036, ROWMX=0.0193 ROWMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 273./ 37./ 94. MMS |
| REQD. DEVELOPMENT LENGTH = 360. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 19148.5 cm^4

3 306. 3 - 12MM 4390. 6000. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 36.18 KN-MET AT 6000.MM, LOAD 4|
| REQD STEEL= 329.MM2, ROW=0.0039, ROWMX=0.0193 ROWMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 273./ 37./ 94. MMS |
| REQD. DEVELOPMENT LENGTH = 360. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 19148.5 cm^4

B E A M N O. 2 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 43.94 KNS Vc= 72.44 KNS Vs= 0.00 KNS
Tu= 2.55 KN-MET Tc= 2.4 KN-MET Ts= 3.4 KN-MET LOAD 4
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 130. MM C/C FOR 2705. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.75 SQ.CM.
AT END SUPPORT - Vu= 44.91 KNS Vc= 71.94 KNS Vs= 0.00 KNS
Tu= 2.55 KN-MET Tc= 2.4 KN-MET Ts= 3.4 KN-MET LOAD 4
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 130. MM C/C FOR 2705. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.75 SQ.CM.
2-92 Tutorial 2

2J 6000X 275X 350 3J

| |
||========= ====================||
| 3No12 H 306. 0.TO 860 3No12|H|306.4390.TO 6000 |
| 22*12c/c130 | | |22*12c/c130 |
| 2No16 H 51. 313.TO 5437 | | | | | | | |
| ================================================================== |
| |
| |

| | | | | | | | | |
| ooo | | | | | | ooo | | ooo |
| 3#12 | | | | | | 3#12 | | 3#12 |
| | | | | | | | | |
| | | 2#16 | | 2#16 | | 2#16 | | |
| | | oo | | oo | | oo | | |
| | | | | | | | | |
| | | | | | | | | |

=====================================================================

BEAM NO. 5 DESIGN RESULTS - FLEXURE PER CODE ACI 318-02

LEN - 6000. MM FY - 415. FC - 25. MPA, SIZE - 275. X 350. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END

1 51. 2 - 16MM 313. 5437. NO NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 39.16 KN-MET AT 3000.MM, LOAD 4|
| REQD STEEL= 366.MM2, ROW=0.0044, ROWMX=0.0193 ROWMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 273./ 41./ 184. MMS |
| REQD. DEVELOPMENT LENGTH = 480. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 20964.0 cm^4

2 306. 3 - 12MM 0. 860. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 33.29 KN-MET AT 0.MM, LOAD 4|
| REQD STEEL= 301.MM2, ROW=0.0036, ROWMX=0.0193 ROWMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 273./ 37./ 94. MMS |
| REQD. DEVELOPMENT LENGTH = 360. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 19148.5 cm^4

3 306. 3 - 12MM 4890. 6000. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 36.18 KN-MET AT 6000.MM, LOAD 4|
| REQD STEEL= 329.MM2, ROW=0.0039, ROWMX=0.0193 ROWMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 273./ 37./ 94. MMS |
| REQD. DEVELOPMENT LENGTH = 360. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 19148.5 cm^4

B E A M N O. 5 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 18.56 KNS Vc= 72.56 KNS Vs= 0.00 KNS
Tu= 4.73 KN-MET Tc= 2.3 KN-MET Ts= 6.3 KN-MET LOAD 5
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 130. MM C/C FOR 2705. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.40 SQ.CM.
 Tutorial 2 2-93

AT END SUPPORT - Vu= 19.11 KNS Vc= 71.87 KNS Vs= 0.00 KNS
Tu= 4.73 KN-MET Tc= 2.3 KN-MET Ts= 6.3 KN-MET LOAD 5
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 130. MM C/C FOR 2705. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.40 SQ.CM.

6J 6000X 275X 350 3J

| |
||========= ==============||
| 3No12 H 306. 0.TO 860 3No12 H 306.4890.TO 6000 |
| 22*12c/c130 22*12c/c130 |
| 2No16 H 51. 313.TO 5437 | | | | |
| ================================================================== |
| |
| |

| | | | | | | | | |
| ooo | | | | | | | | ooo |
| 3#12 | | | | | | | | 3#12 |
| | | | | | | | | |
| | | 2#16 | | 2#16 | | 2#16 | | |
| | | oo | | oo | | oo | | |
| | | | | | | | | |
| | | | | | | | | |

********************END OF BEAM DESIGN**************************

55. DESIGN COLUMN 1 3 4

====================================================================

COLUMN NO. 1 DESIGN PER ACI 318-02 - AXIAL + BENDING

FY - 415.0 FC - 25.0 MPA, RECT SIZE - 275.0 X 300.0 MMS, TIED

AREA OF STEEL REQUIRED = 882.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 12 MM 1.097 4 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 8 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2109.38 1687.50 785.43 97.75 124.5
M0 P-tens. Des.Pn Des.Mn e/h
47.51 -375.48 75.04 51.21 0.19497
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2109.38 1687.50 775.80 88.78 114.4
M0 P-tens. Des.Pn Des.Mn e/h
43.01 -375.48 75.04 3.92 0.01492
--------------------------------------------------------

====================================================================
2-94 Tutorial 2

COLUMN NO. 3 DESIGN PER ACI 318-02 - AXIAL + BENDING

FY - 415.0 FC - 25.0 MPA, CIRC SIZE 350.0 MMS DIAMETER TIED

AREA OF STEEL REQUIRED = 1096.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

10 - 12 MM 1.176 4 STA 0.650

(EQUALLY SPACED)
TIE BAR NUMBER 8 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z/Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2489.81 1991.85 939.46 109.84 116.9
M0 P-tens. Des.Pn Des.Mn e/h
62.23 -469.35 153.06 73.18 0.09660
--------------------------------------------------------

====================================================================

COLUMN NO. 4 DESIGN PER ACI 318-02 - AXIAL + BENDING

FY - 415.0 FC - 25.0 MPA, RECT SIZE - 275.0 X 300.0 MMS, TIED

AREA OF STEEL REQUIRED = 1056.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 20 MM 1.523 5 STA 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 8 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2247.93 1798.34 764.68 123.35 161.3
M0 P-tens. Des.Pn Des.Mn e/h
63.35 -521.51 43.92 10.50 0.06829
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2247.93 1798.34 755.33 111.44 147.5
M0 P-tens. Des.Pn Des.Mn e/h
57.35 -521.51 43.92 47.50 0.30898
--------------------------------------------------------

********************END OF COLUMN DESIGN RESULTS********************

56. END CONCRETE DESIGN

 Tutorial 2 2-95

57. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= TIME= ****

************************************************************
* For questions on STAAD.Pro, please contact *
* Research Engineers Offices at the following locations *
* *
* Telephone Email *
* USA: +1 (714)974-2500 [email protected] *
* CANADA +1 (905)632-4771 [email protected] *
* CANADA +1 (604)629 6087 [email protected] *
* UK +44(1454)207-000 [email protected] *
* FRANCE +33(0)1 64551084 [email protected] *
* GERMANY +49/931/40468-71 [email protected] *
* NORWAY +47 67 57 21 30 [email protected] *
* SINGAPORE +65 6225-6015/16 [email protected] *
* INDIA +91(033)2357-3575 [email protected] *
* JAPAN +81(03)5952-6500 [email protected] *
* CHINA +86(411)363-1983 [email protected] *
* *
* North America [email protected] *
* Europe [email protected] *
* Asia [email protected] *
************************************************************
2-96 Tutorial 2

2.11 Post-Processing

STAAD.Pro offers extensive result verification and visualization

facilities. These facilities are accessed from the Post Processing
Mode. The Post Processing mode is used to verify the analysis and
design results and generate reports.

For this tutorial problem, we shall perform the following tasks:

 Display deflection diagrams

 Annotate Displacements
 Change the Display units for displacement values shown in the
tables.
 Switching between load cases for viewing deflection diagrams.
 Display the force and moment diagrams.
 Changing the degree of freedom for which the force/moment
diagram is plotted
 Annotating the force diagram
 Changing the Display units for the force and moment values
shown in the tables.
 Restricting the load cases for which results are viewed
 Using Member Query
 Viewing Concrete Design results using Query.
 Producing an on-screen report
 Taking pictures
 Creating Customized Reports
 Tutorial 2 2-97

2.11.1 Going to the post-processing mode

Steps:

1. At the end of section 2.9, we saw how one could go directly from
the Analysis window to the post-processing screen. However, the
formal method of accessing the Post Processing mode is either by
clicking on the Post-Processing icon from the top toolbar or from
the Mode menu as shown in the figures below.

Figure 2. 90

Figure 2. 91
2-98 Tutorial 2

2. The Results Setup dialog box appears as shown below. Select the
load cases for which to display the results. For our case, let us
select all the load cases. Then click on the OK button.

Figure 2. 92
 Tutorial 2 2-99

2.11.2 Viewing the deflection diagram

The screen will now look like the figure shown below.

Figure 2. 93

The diagram currently on display is the node deflection diagram for

load case 1 (DEAD LOAD). The title at the bottom of the
diagram is indicative of that aspect. If you, say, wandered off into any
other result diagram, and wanted to get back to the deflection diagram,
just select the Node | Displacement tab along the page
control area on the left side.
2-100 Tutorial 2

Figure 2. 94

The option for selecting the deflection diagram is available from

another facility also - the Results | Deflection menu option - as
shown below.

Figure 2. 95
 Tutorial 2 2-101

2.11.3 Switching between load cases for

viewing the deflection diagram

Steps:

1. To change the load case for which to view the deflection diagram,
you may click in the list box called Active Load and choose the
one you want.

Figure 2. 96

2. Alternatively, either click on the Symbols and Labels icon or, go to

View | Structure Diagrams menu option as shown below.

Figure 2. 97
2-102 Tutorial 2

3. In either case, the Diagrams dialog box comes up. Select the
Loads and Results tab and choose the desired load case from the
Load Case list box. Then, click on OK.

Figure 2. 98
 Tutorial 2 2-103
The diagram below shows the deflected shape of the structure for load
case 3.

Figure 2. 99

4. To display the deflection for say, load case 5 (DEAD + WIND),

follow step 1 or 2 and select load case 5.
2-104 Tutorial 2

The deflection of Load Case 5 will now displayed on the model as shown
below.

Figure 2. 100
 Tutorial 2 2-105

2.11.4 Changing the size of the deflection

diagram

Steps:

If the diagram appears too imperceptible, it may be because it may

be drawn to too small a scale. To change the scale of the deflection
plot, you may

a) click on the Scale icon

Figure 2. 101

b) choose Scale from the Results menu

Figure 2. 102
or
2-106 Tutorial 2

c) go to View | Structure Diagrams | Scales menu option.

All of the above will bring up the following dialog box.

Figure 2. 103

In the Displacement field, specify a smaller number than what is

currently listed, and click on OK. The deflection diagram should now
be larger.
 Tutorial 2 2-107
In the above dialog box, if you switch on the check box Apply
Immediately, pressing the up or down arrow keys alongside the
number will produce immediate results in terms of a smaller or a larger
diagram depending on whether you click the up or the down arrow keys.

Figure 2. 104
2-108 Tutorial 2

2.11.5 Annotating displacements

Annotation is the process of displaying the displacement values on the

screen.

Steps:

1. Select the View Value option from the Results menu.

Figure 2. 105

2. The following dialog box comes up. From the Ranges tab, select
All nodes. If you wish to annotate deflection for just a few nodes,
specify the node numbers in the node list.
 Tutorial 2 2-109

Figure 2. 106

We will annotate the results for all nodes. So, keep the button on
All.

From the Node tab, check the Resultant option. Resultant stands for the
square root of sum of squares of values of X,Y and Z
displacements. Click the Annotate button and notice that the
values appear on the structure. Click the Close button to close the dialog
box.

Figure 2. 107
2-110 Tutorial 2

The following figure shows the annotated deflection diagram for load
case 2.

Figure 2. 108
 Tutorial 2 2-111

2.11.6 Changing the units in which

displacement values are annotated

The units in which displacement values are displayed in the post-

processing mode are referred to as the display units.

Steps:

1. Display units may be modified by using any one of the following

methods:

a. by clicking on the Change Graphical Display Unit icon,

Figure 2. 109

b. by going to Tools | Set Current Display Unit menu option

Figure 2. 110
or,
2-112 Tutorial 2

c. by selecting the View | Options menu option.

Figure 2. 111

2. In the Options dialog box that comes up, select the Structure
Units tab. Change the Dimensions of Displacement from
Millimeter to say, cm or inches or anything else you desire, and click
on OK.

Figure 2. 112
 Tutorial 2 2-113
The diagram will be updated to reflect the new units.

Figure 2. 113
2-114 Tutorial 2

2.11.7 The Node Displacement Table

Upon entering the Post-Processing mode, the first screen that we

came across is shown below.

Figure 2. 114

For the Node | Displacement page on the left side, notice that there are 2
tables displayed along the right side. The upper table, called
the Node Displacements table, lists the displacement values for every
node for every selected load case. Load cases may be
selected or de-selected for the purpose of this table from the
Results | Select Load Case menu. (See section 2.11.16 for details) The
lower table is called the Beam relative displacement table.
 Tutorial 2 2-115
If you happen to close down any of these tables, you can restore them
from the View | Tables menu.

Figure 2. 115

The Node Displacement table window has two tabs: All and
Summary (see figure below).

Figure 2. 116
2-116 Tutorial 2

All - This tab presents all nodal displacements in tabular form for all load
cases and all degrees of freedom.

Figure 2. 117

Summary - This tab, shown in the figure below, presents the

maximum and minimum nodal displacements (translational and
rotational) for each degree of freedom. All nodes and all Load
Cases specified during the Results Setup are considered. Maximum values
for all degrees of freedom are presented with the
corresponding Node of occurrence and Load Case number (L/C).

Figure 2. 118
 Tutorial 2 2-117
For the Beam Relative Displacement table, the details are as
follows :

All
The All tab presents the displacements of members at intermediate section
points. All specified members and all specified load cases
are included. The table shows displacements along the local axes of the
members, as well as their resultants.

Max Displacements
The Max Displacements tab presents the summary of maximum
sectional displacements (see figure below). This table includes the
maximum displacement values and location of its occurrence along
the member, for all specified members and all specified load cases.
The table also provides the ratio of the span length of the member
to the resultant maximum section displacement of the member.

Figure 2. 119
2-118 Tutorial 2

The sub-pages under the Node page are described below in brief.

Page Sub-Page Purpose

Node Displacement Displays nodal displacements along with

tabular results for Node-Displacements
and sectional Beam displacements.

Reactions Displays support reactions on the

drawing as well as in a tabular form.

Modes Displays mode shapes for the selected

Mode shape number. The eigenvectors
are simultaneously displayed in tabular
form. This Page appears only for
dynamic analyses cases, namely,
response spectrum, time history, and if
modal calculations are requested.

Time History Displays Time history plots, for time

history analysis. This sub-page too will
appear only if time history analysis is
performed.
 Tutorial 2 2-119

2.11.8 Displaying force/moment diagrams

Steps:

1. The simplest method to access the facilities for displaying

force/moment diagrams is from the Beam | Forces page along the
page control area on the left side of the screen. The bending
moment MZ will be plotted by default, evidence of which can be
found in the form of the Mz icon show in the diagram below which
becomes active.

Figure 2. 120
2-120 Tutorial 2

Figure 2. 121
 Tutorial 2 2-121
2. The option for selecting the force/moment diagram is available
from another facility also - the Results | Bending Moment menu
option - as shown below.

Figure 2. 122
2-122 Tutorial 2

2.11.9 Switching between load cases for

viewing the force/moment diagram

Steps:

1. To change the load case for which to view the force/moment

diagram, you may click in the list box called Active Load and
choose the one you want.

Figure 2. 123

2. Alternatively, either click on the Symbols and Labels icon or, go to

View | Structure Diagrams menu option as shown below.

Figure 2. 124
 Tutorial 2 2-123
3. In either case, the Diagrams dialog box comes up. Select the Loads
and Results tab and choose the second load case (LIVE LOAD)
from the Load Case list box. Also, let us check the Shear yy check
box. Then, click on OK.

Figure 2. 125
2-124 Tutorial 2

4. The figure below shows the shear force diagram for load case 2.

Figure 2. 126

5. To display the bending moment diagram for say, load case 4 (DEAD
+ LIVE), follow steps 1 to 3 above and select load case 4.
 Tutorial 2 2-125
The following diagram should appear in the drawing area:

Figure 2. 127
2-126 Tutorial 2

2.11.10 Changing the size of the force/

moment diagram

Steps:

If the diagram appears too imperceptible, it may be because it may

be drawn to too small a scale. To change the scale of the moment
plot, you may

a) click on the Scale icon

Figure 2. 128

b) choose Scale from the Results menu

Figure 2. 129

or
 Tutorial 2 2-127
c) go to View | Structure Diagrams | Scales menu option. All
of the above will bring up the following dialog box.

Figure 2. 130

In the Bending field, specify a smaller number than what is

currently listed, and click on OK. The moment diagram should now be
larger.

In the above dialog box, if you switch on the check box Apply
Immediately, pressing the up or down arrow keys alongside the
number will produce immediate results in terms of a smaller or a
2-128 Tutorial 2

larger diagram depending on whether you click the up or the down arrow
keys.

Figure 2. 131
 Tutorial 2 2-129

2.11.11 Changing the degree of freedom for

which forces diagram is plotted

Force and moment diagrams can be plotted for 6 degrees of

freedom – Axial, Shear-Y, Shear-Z, Torsion, Moment-Y, Moment-
Z. One may select or de-select one of more of these degrees of
freedom from View | Structure Diagrams | Loads and Results.

Figure 2. 132

All degrees of freedom currently plotted will be indicated with a tick

mark.
2-130 Tutorial 2

The icons of the Results toolbar may also be used to turn on/off
specific degrees of freedom.

Figure 2. 133

For the sake of easy identification, each degree of freedom (d.o.f) has
been assigned a different color. One may change the color for that d.o.f.
by clicking on the color button alongside the d.o.f, and make a new
choice from the color palette.

Figure 2. 134

The appearance of the diagram may also be set to one of the 3 –

Hatch, Fill or Outline by turning on the relevant option in the dialog
box shown earlier.

Figure 2. 135
 Tutorial 2 2-131

2.11.12 Annotating the force/moment diagram

Steps:

1. Annotation is the process of displaying the force/moment values on

the screen. Select the View Value option from the Results menu.

Figure 2. 136

2. The following dialog box comes up. From the Ranges tab, select
All members. If you wish to annotate the force/moment for just a
few members, specify the beam numbers in the beam list.

Figure 2. 137

We will annotate the results for all members. So, keep the button
on All.
2-132 Tutorial 2

From the Beam Results tab, check the Bending - Maximum option.
Click the Annotate button and notice that the values appear on the
structure. Click the Close button to close the dialog box.

Figure 2. 138
 Tutorial 2 2-133
The following figure shows the annotated MZ diagram for load case 5.

Figure 2. 139
2-134 Tutorial 2

2.11.13 Changing the units in which

force/moment values are annotated

Steps:

1. The units in which force and moment values are displayed in the
post-processing mode are referred to as the display units.

Display units may be modified by using any one of the following

methods:

a. by clicking on the Change Graphical Display Unit icon

Figure 2. 140

b. by going to Tools | Set Current Display Unit menu option

Figure 2. 141
or,
 Tutorial 2 2-135
c. by selecting the View | Options menu option.

Figure 2. 142

2. In the Options dialog box that comes up, select the Force Units
tab. For bending moments, change the Moment unit from its
current setting to one of the choices available, say, Mton-m or kip-
ft or anything else you desire, and select OK.

Figure 2. 143
2-136 Tutorial 2

The diagram will be updated to reflect the new units.

Figure 2. 144
 Tutorial 2 2-137

2.11.14 Beam Forces Table

When we select the Beam | Forces page from the page control area
on the left side, the screen that appears is shown below.

Figure 2. 145

The axial forces and shear forces, bending and torsional moments
in all selected beams for all selected load cases are displayed in a
tabular form along the right half of the screen. Load cases may be
selected or de-selected for the purpose of this table from the
Results | Select Load Case menu. (See section 2.11.16 for details)
2-138 Tutorial 2

If you happen to close down any of these tables, you can restore them
from the View | Tables menu.

Figure 2. 146

The Beam End Forces table window has three tabs: All, Summary
and Envelope.

Figure 2. 147
 Tutorial 2 2-139
All - This tab presents all forces and moments corresponding to all
6 degrees of freedom at the start and end of each selected member
for all selected load cases.

Figure 2. 148

Summary - This tab, shown in the next figure, presents the

maximum and minimum values (forces and moments) for each
degree of freedom. All beams and all Load Cases specified during
the Results Setup are considered. Maximum values for all degrees
of freedom are presented with the corresponding Node of
occurrence and Load Case number (L/C).
2-140 Tutorial 2

Figure 2. 149

Envelope : This tab shows a table consisting of the maximum and

minimum for each degree of freedom for each member, and the
load case responsible for each of those values.

Figure 2. 150
 Tutorial 2 2-141

2.11.15 Viewing the force/moment diagrams

from the Beam | Graphs page

The Graphs page in the Post Processing Mode allows us to

graphically view moments and forces such as Axial, Bending zz,
Shear yy and Combined Stresses for individual members. Select the
Graphs sub-page nested under the Beam page from the left side of
the screen as shown below.

Figure 2. 151
2-142 Tutorial 2

The Main Window area of the screen shows the loading on the
structure. On the right side of the screen, the force/moment
diagrams appear (see figure below). When we highlight a member
in the main window by clicking on it, the graphs are plotted for
that member in the data area.

The following figure shows the graphs plotted for member 1 for load
case 4.

Figure 2. 152
 Tutorial 2 2-143
The following figure shows the graphs plotted for member 2 for the
same load case.

Figure 2. 153

We can change the degree of freedom for which results are plotted
by doing the following. Go into one of the 3 drawing windows on
the right side, and click the right mouse button. The following
dialog box will appear.
2-144 Tutorial 2

Figure 2. 154

Select Diagrams. In the dialog box which appears, switch

on/switch off the degrees of freedom you desire.

Figure 2. 155

Click on OK and that degree of freedom will be plotted in that

window.
 Tutorial 2 2-145

2.11.16 Restricting the load cases for which

results are viewed

Steps:

1. To restrict the load cases for which results are viewed, either click

on the Results Setup icon or, go to Results | Select Load Case

menu option as shown below.

Figure 2. 156
2-146 Tutorial 2

2. In the Results Setup dialog box that comes up, let us first un-select
the already selected load cases by clicking on the button.

Figure 2. 157

3. Select load cases 1 (DEAD LOAD) and 3 (WIND LOAD) by

holding the ‘Ctrl’ key down. Then, click on the button. After
the load cases have been selected, click on the OK button.

Figure 2. 158
 Tutorial 2 2-147

2.11.17 Using Member Query

Member query is a facility where several results for specific

members can be viewed at the same time from a single dialog box.
It is also a place from where many of the member attributes such as
the property definition, specifications (releases, truss, cable, etc.)
and beta angle can be changed for input purposes.

Steps:

To access this facility, first select the member. Then, either go to Tools |
Query | Member menu option or, double-click on the member. Let us
try double-clicking on member 4.

Figure 2. 159
2-148 Tutorial 2

As we double-click on member 4, the following dialog box comes up.

Let us take a look at the Property tab.

Figure 2. 160

The figure above shows where the buttons are located on the
member query box. If the member contains output result tabs
(Shear/Bending, Deflection, Steel Design, etc.) in the query box,
changing member attributes like releases will cause these result
tabs to disappear. This is due to the fact that the current output no
longer reflects the new input.

NOTE: If you assign or change property by clicking on the

Assign/Change Property button in the above dialog box, ensure
that you keep the check mark on “Apply to this Member only” in the
ensuing dialog box. Else, changing the member attributes for one
member will subsequently change the attributes of all other members
belonging to the same attribute list. For example, if the current
member's property is also assigned to other members,
changing the property on the current member will change the
property of all the members.
 Tutorial 2 2-149
Let us click on the Shear/Bending tab. The following dialog box
appears.

Figure 2. 161

The above page contains facilities for viewing values for shears and
moments, selecting the load cases for which those results are
presented, a slider bar (see next figure) for looking at the values at specific
points along the member length, and a Print option for
printing the items on display. Experiment with these options to see what
sort of results you can get. Grab the slider bar using the
mouse and move it to obtain the values at specific locations.
2-150 Tutorial 2

Figure 2. 162

Another page (Deflection) of the above dialog box is shown below.

Figure 2. 163
 Tutorial 2 2-151
The Concrete Design page of the above dialog box is shown
below.

Figure 2. 164

To look at the results of another member using this query facility, simply
close down this query dialog box and repeat the steps
outlined earlier in this section for the desired member.
2-152 Tutorial 2

2.11.18 Producing an on-screen report

Steps:

Occasionally, we will come across a need to obtain results

conforming to certain restrictions, such as, say, the resultant node
displacements for a few selected nodes, for a few selected load
cases, sorted in the order from low to high, with the values
reported in a tabular form. The facility which enables us to obtain such
customized on-screen results is the Report menu on top of the screen.

1. Let us create one such report. We will create a table that shows the
member major axis moment (MZ) values sorted in the order High
to Low, for members 1 and 4 for all the load cases. The first step to
do this is to select members 1 and 4 from the structure. With the
beams cursor active, select members 1 and 4 using the mouse, or
use the Select | By List | Beams option of the Select menu and type
1 and 4 as the member numbers. Next, go to the Report | Beam
End Forces menu option as shown below.

Figure 2. 165
 Tutorial 2 2-153
2. In the dialog box that appears, select the Sorting tab. Let us select
Moment-Z as the End Force, set the Sorting Order to List from
High to Low, and switch on Absolute values under If Sorting
done. (If we wish to save this report for future use, we may select
the Report tab, provide a title for the report, and turn on the Save
ID option.) Under the Loading tab, make sure all the 5 load cases
have been selected. Then, click on the OK button.

Figure 2. 166

The next figure shows the member end forces sorted table with the MZ
values sorted from High to Low based on Absolute numbers.

Figure 2. 167
2-154 Tutorial 2

3. To print this table, click the right mouse button anywhere within
the table. A list of options will appear.

Figure 2. 168

Select the print option to get a hardcopy of the report.

 Tutorial 2 2-155

2.11.19 Taking Pictures

There are several options available for taking pictures. The

simplest of these is in the edit menu and is called Copy Picture. It transfers
the contents of the active drawing window to the windows clipboard. We
can then go into any picture processing program like Microsoft Paint or
Microsoft Word and paste the picture in that
program for further processing.

Another more versatile option enables us to include any "snapshot"

or picture of the drawing window into a report. It is called Take
Picture and is under the Edit menu. Let us examine this feature.

Steps:

1. To take a picture, either click on the Take Picture icon or, go to

Tools | Take Picture menu option.

Figure 2. 169
2-156 Tutorial 2

2. The following dialog box comes up. Here, we may provide a

caption for the picture so that it may be identified later on.

Figure 2. 170

This picture will be saved till we are ready to produce a customized report
of results. Proceed to the next section for details.
 Tutorial 2 2-157

2.11.20 Creating Customized Reports

STAAD.Pro offers extensive report generation facilities. Items which

can be incorporated into such reports include input
information, numerical results, steel design results, etc. One can choose
from among a select set of load cases, mode shapes,
structural elements, etc.. We may include any "snapshot" or picture
of the screen taken using the Take Picture toolbar icon. Other
customizable parameters include the font size, title block, headers, footers,
etc.

1. The Report Setup utility may be accessed either by selecting the

Reports Page or by clicking on the Report Setup icon.

Figure 2. 171
2-158 Tutorial 2

In either case, the following dialog box appears:

Figure 2. 172

Different tabs of this dialog box offer different options. The Items
tab lists all available data which may be included in the report.
Note that the items under the Selected list are the ones which have been
selected by default.

Available items are classified into seven categories: Input, Output,

Pictures, Reports, STAAD.etc output, Steel Design Output and
Advanced Query Reports.
 Tutorial 2 2-159

Figure 2. 173

2. In our report, we want to show Job Information, Node

Displacement Summary, Beam Max Moments, and Picture 1. Job

Information is already selected by default.

From the Available list box, select Output. From the available
output items, select Node Displacement Summary and Beam Max
Moments.

Then select Pictures from the Available list box and select Picture
1.

When all the items have been selected, the Report Setup dialog box should
appear as shown below.
2-160 Tutorial 2

Figure 2. 174

The Report Detail Increments check box at the bottom indicates the
number of segments into which a member would be divided for
printing sectional displacements, forces, etc.

3. Click on the Load Cases tab to select the Load Cases to be

included in the report. The Grouping buttons indicate whether the report
data will be grouped by Node/Beam numbers or by Load
Case number. In the first case, all Load Case results will appear
under a particular Node or Beam. In the second case, results for all
Nodes or Beams for a particular Load Case will appear together.
 Tutorial 2 2-161

Figure 2. 175

4. Click on the Picture Album tab to visually identify the pictures

taken earlier. The following figure displays Picture 1 as stored by
the program.

Figure 2. 176
2-162 Tutorial 2

The Options tab lets you include Header, Footer, Page Numbers, Table
Grids, fonts for Column Heading and Table data, etc.

The Name and Logo tab allows you to enter the Company Name
and Logo. Click on the blank area and type the name and address
of the company. Click on the Font button in the Text group and
adjust the font to be Arial 16 Pt Bold. Click on the Right radio button
in the Alignment group under Text to right-align the
company name.

Figure 2. 177

5. Click OK to finish or click Print to print the report. However, it is

always a good idea to first preview the report before printing it.
 Tutorial 2 2-163
To preview the report just created, select the Print Preview icon from
the Toolbar.

Figure 2. 178

The first and the last pages of the report are shown in the next two figures.
2-164 Tutorial 2

Figure 2. 179
 Tutorial 2 2-165

Figure 2. 180

This brings us to the end of this tutorial. Though we have covered

a large number of topics, there are several more in various menus
and dialog boxes. Happy exploring !!!!!
2-166 Tutorial 2
 3-1

Tutorial Problem 3: Analysis of a slab

Section 3
This tutorial provides step-by-step instructions for modelling and analysis
of a slab supported along two edges. The following topics are covered:

 Starting the program

 Modelling the slab using quadrilateral plate elements
 Specifying slab properties and material constants
 Specifying supports
 Specifying loads
 Specifying the analysis type
 Viewing results for individual plates
3-2 Tutorial 3

3.1 Methods of creating the model

As explained in Section 1.1 of tutorial problem 1, there are two

methods of creating the structure data:

a) using the graphical model generation mode, or graphical

user interface (GUI) as it is usually referred to.
b) using the command file.

Both methods of creating the model are explained in this tutorial. The
graphical method is explained from Section 3.2 onwards. The command
file method is explained in Section 3.8.
 Tutorial 3 3-3

3.2 Description of the tutorial problem

The structure for this project is a slab fixed along two edges. We
will model it using 6 quadrilateral (4-noded) plate elements. The
structure and the mathematical model are shown in the figures
below. It is subjected to selfweight, pressure loads and temperature loads.
Our goal is to create the model, assign all required input,
perform the analysis, and go through the results.

Figure 3. 1
3-4 Tutorial 3

Figure 3. 2
 Tutorial 3 3-5
BASIC DATA FOR THE STRUCTURE

ATTRIBUTE DATA

Element properties Slab is 300mm thick

Material Constants E, Density, Poisson, Alpha – Default values for

concrete

Supports Nodes along 2 edges are fixed as shown in Figure 3.2

Primary Loads Load 1: Selfweight

Load 2: Pressure Load of 300Kg/sq.m. acting

vertically downwards

Load 3: 75 degree F uniform expansion, plus top

surface is 60 degrees hotter than the
bottom

Combination Loads Case 101: Case 1 + Case 2

Case 102: Case 1 + Case 3

Analysis Type Linear Elastic

3-6 Tutorial 3

3.3 Starting the program

Select the STAAD.Pro icon from the STAAD.Pro 2006 program group.

Figure 3. 3
 Tutorial 3 3-7
The STAAD.Pro Graphical Environment will be invoked and the
following screen comes up.

Figure 3. 4

This New dialog box will come up every time we start the program.
If you wish to turn this feature off, simply uncheck the Display this
dialog box at the Startup box at the lower left hand corner. It can
be turned on again at a later time when File | New is invoked from the
main menu.
3-8 Tutorial 3

Note about the unit system :

There are two base unit systems in the program which control the
units (length, force, temperature, etc.) in which, values,
specifically results and other information presented in the tables and
reports, are displayed in. The base unit system also dictates what type
of default values the program will use when attributes
such as Modulus of Elasticity, Density, etc., are assigned based on
material types – Steel, Concrete, Aluminum – selected from the
program’s library (Please refer to Section 5 of the STAAD.Pro
Technical Reference Manual for details). These two unit systems are
English (Foot, Pound, etc.) and Metric (KN, Meter, etc.)

If you recall, one of the choices made at the time of installing

STAAD.Pro is this base unit system setting. That choice will serve
as the default until we specifically change it.

The place from where we can change this setting is under the File |
Configure menu. To get to that option, first close down the dialog
box shown in the earlier figure by clicking on Cancel. Then, click
on the File | Configure menu option and choose the appropriate
unit system you want. For this tutorial, let us choose the Metric
units (KN, Meter, etc.).

Figure 3. 5
 Tutorial 3 3-9

Figure 3. 6

Click on the Accept button to close the above dialog box.

3-10 Tutorial 3

Following this, select File | New once again.

Figure 3. 7

The dialog box shown in Figure 3.4 will re-appear.

 Tutorial 3 3-11

3.4 Creating a new structure

1. In the New dialog box, we provide some crucial initial data

necessary for building the model.

The structure type is to be defined by choosing from among Space,

Plane, Floor and Truss. A Space type is one where the structure,
the loading or both, cause the structure to deform in all 3 global
axes (X, Y and Z). In a Plane type, the geometry, loading and
deformation are restricted to the global X-Y plane only. A Floor
type is a structure whose geometry is confined to the X-Z plane. A
Truss type of structure carries loading by pure axial action. Truss
members are deemed incapable of carrying shear, bending and
torsion. For our model, let us choose Space.

Let us choose Meter as the length unit and Kilo Newton as the
force unit in which we will start to build the model. The units can
be changed later if necessary, at any stage of the model creation.

We also need to provide a name in the File Name edit box. This is
the name under which the structure data will be saved on the
computer hard disk. The name “Structure?” (? will be a number) is
recommended by the program by default, but we can change it to
any name we want. Let us choose the name Plates Tutorial.

A default path name - the location on the computer drive where the
file will be saved - is provided by the program under Location. If
you wish to save the file in a different location, type in the name,
or click the button and specify the desired path.

After specifying the above input, click on the Next button.

3-12 Tutorial 3

Figure 3. 8
2. In the next dialog box, we choose the tools to be used to initially
construct the model. Add Beams, Add Plates or Add Solids are,
respectively, the starting points for constructing beams, plates or
solids. Open Structure Wizard provides access to a library of
structural templates which the program comes equipped with.
Those template models can be extracted and modified
parametrically to arrive at our model geometry or some of its parts.
If the model is to be created initially using the STAAD command
language, the Open Editor box can take us to the STAAD editor.
Please remember that all these options are also available from the
menus and dialog boxes of the GUI, even after we dismiss this
dialog box.

Note: If you wish to use the Editor to create the model, choose Open
STAAD Editor, click Finish, and proceed to Section 3.8.
 Tutorial 3 3-13
For our model, let us check the Add Plate option. Click on the
Finish button. The dialog box will be dismissed and the
STAAD.Pro graphical environment will be displayed.

Figure 3. 9
3-14 Tutorial 3

3.5 Elements of the STAAD.Pro screen

The STAAD.Pro main window is the primary screen from where the
model generation process takes place. It is important to
familiarize ourselves with the components of that window before we
embark on creating the RC Frame. Section 1.5 in tutorial
problem 1 of this manual explains the components of that window
in detail.
 Tutorial 3 3-15

3.6 Building the STAAD.Pro model

We are now ready to start building the model geometry. The steps and,
wherever possible, the corresponding STAAD.Pro commands (the
instructions which get written in the STAAD input file) are
described in the following sections.
3-16 Tutorial 3

3.6.1 Generating the model geometry

The structure geometry consists of joint numbers, their

coordinates, member numbers, the member connectivity
information, plate element numbers, etc. From the standpoint of the
STAAD command file, the commands to be generated are :

JOINT COORDINATES
1000;2200;3202;4002
5400;6402;7600;8602
9 2 0 4 ; 10 0 0 4 ; 11 4 0 4 ; 12 6 0 4
ELEMENT INCIDENCES SHELL
11234;22563;35786
4 4 3 9 10 ; 5 3 6 11 9 ; 6 6 8 12 11

In this tutorial, we will explore 4 different methods to create the

model shown in section 3.2:

1. Using a mixture of drawing an element and the Copy/Paste

facility.
2. Using a mixture of drawing an element and the
Translational Repeat facility.
3. Using the Structure Wizard facility in the Geometry menu.
4. Using the Mesh Generation facility of the main graphical
screen.
 Tutorial 3 3-17

Creating the Plates - Method 1

Steps:

The Grid Settings

1. We selected the Add Plate option earlier to enable us to add plates

to create the structure. This initiates a grid in the main drawing
area as shown below. The directions of the global axes (X, Y, Z) are
represented in the icon in the lower left hand corner of the
drawing area. (Note that we could initiate this grid by selecting the
Geometry | Snap/Grid Node | Plate menu option also.)

Figure 3. 10
3-18 Tutorial 3

It is worth paying attention to the fact that when we chose the Add Plate
option in section 3.4, the page control area has been
automatically set up to have the Geometry – Plate page be in focus.

Figure 3. 11
2. A Snap Node/Plate dialog box also appears in the data area on the
right side of the screen. The Linear tab is meant for placing the
construction lines perpendicular to one another along a "left to
right - top to bottom" pattern, as in the lines of a chess board. The
Radial tab enables construction lines to appear in a spider-web
style, which makes it is easy to create circular type models where
members are modelled as piece-wise linear straight line segments.
The Irregular tab can be used to create gridlines with unequal
spacing that lie on the global planes or on an inclined plane. We
will use the Linear tab.

In our structure, the elements lie in the X-Z plane. So, in this
dialog box, let us choose X-Z as the Plane of the grid. The size of the
model that can be drawn at any time is controlled by the
number of Construction Lines to the left and right of the origin of axes,
and the Spacing between adjacent construction lines. By
setting 6 as the number of lines to the right of the origin along X, 4
along Z, and a spacing of 1 meter between lines along both X and
 Tutorial 3 3-19
Z (see next figure) we can draw a frame 6m X 4m, adequate for
our model. Please note that these settings are only a starting grid
setting, to enable us to start drawing the structure, and they do not restrict
our overall model to those limits. In fact, we do not even need this 6m X
4m grid. The method we are using here requires
just a 2m X 2m grid since we are about to draw just a single
element.

Figure 3. 12
3-20 Tutorial 3

Creating element 1

3. The four corners of the first element are at the coordinates (0, 0,
0), (2, 0, 0), (2, 0, 2), and (0, 0, 2) respectively. To start creating
the nodes, let us first activate the Snap Node/Plate button by
clicking on it. Then, with the help of the mouse, click at the origin (0, 0, 0)
to create the first node.

Figure 3. 13

4. In a similar fashion, click on the remaining three points to create

nodes and automatically join successive nodes by a plate.

(2, 0, 0), (2, 0, 2) and (0, 0, 2)

The exact location of the mouse arrow can be monitored on the

status bar located at the bottom of the window where the X, Y, and
Z coordinates of the current cursor position are continuously
updated.
 Tutorial 3 3-21
When steps 1 to 4 are completed, the element will be displayed in the
drawing area as shown below.

Figure 3. 14
3-22 Tutorial 3

5. At this point, let us remove the grid display from the structure. To
do that, click on the Close button in the Snap Node/Plate dialog
box.

Figure 3. 15
 Tutorial 3 3-23
The grid will now be removed and the structure in the main
window should resemble the figure shown below.

Figure 3. 16

6. It is very important that we save our work often, to avoid loss of

data and protect our investment of time and effort against power
interruptions, system problems, or other unforeseen events. To save the file,
pull down the File menu and select the Save command.

7. For easy identification, the entities drawn on the screen can be

labeled. Let us display the plate numbers. (Please refer to the
‘Frequently Performed Tasks’ section at the end of this manual to learn
more about switching on node/beam/plate labels.)
3-24 Tutorial 3

The following figure illustrates the plate number displayed on the

structure. The structure in the main window should resemble the
figure shown below.

Figure 3. 17

If you are feeling adventurous, here is a small exercise for you. Change
the font of the plate labels by going to the View menu and selecting the
Options command, and then selecting the appropriate tab (Plate labels)
from the Options dialog box.
 Tutorial 3 3-25
Creating element 2

8. Examining the structure shown in section 3.2 of this tutorial, it can

be seen that the remaining elements can be easily generated if we
could copy the existing plate and then, paste the copied unit at specific
distances. The program does indeed have a Copy-Paste facility and it
is under the Edit menu.

First, select plate 1 using the Plates Cursor .

9. Click the right mouse button and choose Copy from the pop-up
menu (or click on the Edit menu and choose Copy). Once again,
click the right mouse button and select Paste Plates (or choose
Paste Plates from the Edit menu) as shown below.

Figure 3. 18 Figure 3. 19
3-26 Tutorial 3

10. Since this facility allows us to create only one copy at a time, all
that we can create from element 1 is element 2. The four nodes of
element 2 are at distance of X = 2, Y = 0, and Z = 0 away from
element 1. So, in the dialog box that comes up, provide 2, 0, and 0
for X, Y and Z respectively and click on the OK button.

Figure 3. 20

The model will now look like the one shown below.

Figure 3. 21
 Tutorial 3 3-27
Creating element 3

11. The nodes of element 3 are at X = 4m away from those of element

1. So, let us create the third element by repeating steps 8 to 10
except for providing 4m for X in the Paste with Move dialog box.

Alternatively, we could use element 2 as the basis for creating

element 3, in which case, the X increment will be 2m. If you make
a mistake and end up pasting the element at a wrong location, you
can undo the operation by selecting Undo from the Edit menu.

After creating the third element, the model should look like the one shown
below.

Figure 3. 22

Click anywhere in the screen to un-highlight the highlighted plate.

Creating elements 4, 5 and 6

12. The elements 4, 5 and 6 are identical to the first three elements
except that their nodes are at a Z distance of 2m away from the
corresponding nodes of elements 1 to 3. We can hence use the
Copy-Paste technique and specify the Z increment as 2m.

Select all three of the existing plates by rubber-banding around them

using the mouse.
3-28 Tutorial 3

13. Click the right mouse button and choose Copy from the pop-up
menu (or click on the Edit menu and choose Copy). Once again,
click the right mouse button and select Paste Plates (or choose
Paste Plates from the Edit menu).

14. Provide 0, 0, and 2 for X, Y and Z respectively in the Paste with

Move dialog box that comes up. Then, click on the OK button and
observe that three new elements are created.

Since some elements are still highlighted, click anywhere in the

drawing area to un-highlight those elements.

The model, with all the six plates generated, will now look as shown
below.

Figure 3. 23
 Tutorial 3 3-29
If you want to proceed with assigning the remainder of the data,
go to section 3.6.2.

If instead, you wish to explore the remaining methods of creating this

model, the current structure will have to be entirely deleted. This can be
done using the following procedure.

From the Select menu, choose By All | All Geometry option. The
entire structure will be highlighted. Hit the key on your
keyboard. A message box shown below will appear. Click on the
OK button.

Figure 3. 24

As we click on the OK button, the following message box appears. Let us

say Yes. The message box will be dismissed and the entire structure will
be deleted.

Figure 3. 25
3-30 Tutorial 3

Creating the Plates - Method 2

Steps:

Creating element 1

1. In this method, we will be using STAAD’s Translational Repeat

facility to create our model. To utilize this facility, we need at least one
existing entity to use as the basis for the translational repeat.
So, let us follow steps 1 to 7 from ‘Method 1’ to create the first
element. Once that is done, our model will look like the one shown below.

Note: If you have trouble bringing the grid settings dialog box, go
to the Geometry menu and select Snap/Grid Node Plate.

Figure 3. 26
 Tutorial 3 3-31
Creating elements 2 and 3

2. In Method 1, it required two separate executions of the Copy/Paste

function to create elements 2 and 3. That is because, that facility
does not contain a provision for specifying the number of copies one
would like to create. Translational Repeat is a facility where such a
provision is available.

Select plate 1 using the Plates Cursor . (Please refer to the

‘Frequently Performed Tasks’ section at the end of this manual to learn
more about selecting plates.)

3. Click on the Translational Repeat icon or select the Geometry |

Translational Repeat menu option as shown below.

Figure 3. 27 Figure 3. 28
3-32 Tutorial 3

The 3D Repeat dialog box comes up. By default (when the

Geometry Only option is not checked), all loads, properties, design
parameters, member releases, etc. on the selected entities will
automatically be copied along with the entities. By checking the
new option labeled Geometry Only, the translational repeating will
be performed using only the Geometry data. In our example, it does
not matter because no other attributes have been assigned yet.

4. To create elements 2 and 3 along the X direction, specify the

Global Direction as X, No of Steps as 2 and the Default Step
Spacing (along X) as 2m. The Link Steps option is applicable when the
newly created units are physically removed from the existing
units, and when one wishes to connect them using members.
Renumber Bay enables us to use our own numbering scheme for
entities that will be created, instead of using a sequential
numbering that the program does if no instructions are provided.
Let us leave these boxes unchecked. Then, click on OK.

Figure 3. 29

Since element 1 is still highlighted, click anywhere in the drawing area to

un-highlight it.
 Tutorial 3 3-33
The model will now look as shown below.

Figure 3. 30

Creating elements 4, 5 and 6

5. Let us follow the same Translational Repeat method to create these

elements. Select all the three existing plates by rubber-banding
around them using the mouse. Make sure that before you do this,
the cursor type is the Plates Cursor , else, no plates will be
selected.

6. Repeat steps 3 and 4 but this time, specify the Global Direction as
Z, No of Steps as 1 and the Default Step Spacing as 2m. Leave all
the other boxes unchecked. Then, click on OK.

All the 6 elements are now created.

Since some of the plates are still highlighted, click anywhere in the
drawing area to un-highlight them.
3-34 Tutorial 3

Our model will now look like the one shown below.

Figure 3. 31

If you want to proceed with assigning the remainder of the data, go

to section 3.6.2.

Instead, if you wish to explore the remaining methods of creating this

model, the current structure will have to be entirely deleted. This can be
done using the following procedure.

From the Select menu, choose By All | All Geometry option. The
entire structure will be highlighted. Hit the key on your
keyboard. A message box shown below will appear. Click on the
OK button.

Figure 3. 32
 Tutorial 3 3-35
As we click on the OK button, the following message box appears. Let us
say Yes. The message box will be dismissed and the entire structure will
be deleted.

Figure 3. 33
3-36 Tutorial 3

Creating the Plates - Method 3

Steps:

There is a facility in STAAD called Structure Wizard which offers

a library of pre-defined structure prototypes, such as Pratt Truss,
Northlight Truss, Cylindrical Frame, etc. A surface entity such as
a slab or wall, which can be defined using 3-noded or 4-noded
plate elements is one such prototype. We can also create our own
library of structure prototypes. From this wizard, a structural
model may parametrically be generated, and can then be
incorporated into our main structure. Structure Wizard can hence be
thought of as a store from where one can fetch various
components and assemble a complete structure.

1. Select the Geometry | Run Structure Wizard menu option from the
top menu bar.

Figure 3. 34
 Tutorial 3 3-37
The Structure Wizard window opens up as shown below.

Figure 3. 35

(Note that the Open Structure Wizard option in the Where do you want
to go? dialog box in the beginning stage of creating a new structure – see
Figure 3.9 – also brings up this facility.)
3-38 Tutorial 3

2. The unit of length should be specified prior to the generation of a

model. From the File menu of this Structure Wizard window, click
Select Units. In the Select Units dialog box that comes up, we can
select one of the units of length from Imperial (inch, feet) or
SI/Metric (millimeter, centimeter, meter) system of units. Let us choose
Meters and click on the OK button.

Figure 3. 36 Figure 3. 37

3. From the Model Type list box, select Surface/Plate Models as

shown below.

Figure 3. 38
 Tutorial 3 3-39
4. To select the Quad Plate option, click on it using the mouse.

Figure 3. 39

5. Then, using the mouse, either double-click on the Quad Plate

option or, drag the Quad Plate option to the right side of the
Structure Wizard window as shown below.

Figure 3. 40
3-40 Tutorial 3

6. A dialog box by the name Select Meshing Parameters comes up. In

this box, we specify, among other things, two main pieces of
information - a) the dimensions of the boundary (or superelement
as it is commonly known) from which the individual elements are
generated b) the number of individual elements that must be
generated. (a) is defined in terms of the X, Y, Z coordinates of its
Corners A, B, C and D. (b) is defined in terms of the number of
divisions along sides AB, BC, etc.

Let us provide the Corners, the Bias and the Divisions of the model
as shown in the figure below. Then, click on the Apply button.

Figure 3. 41

If you made a mistake and wish to bring up the above dialog box again,
click the right mouse button in the drawing area and choose Change
Property.

Figure 3. 42
 Tutorial 3 3-41
7. To transfer the model to the main window, select File | Merge
Model with STAAD.Pro Model as shown below.

Figure 3. 43

8. When the following message box comes up, let us confirm our
transfer by clicking on the Yes button.

Figure 3. 44

The dialog box shown in the next figure comes up. If we had an existing
structure in the main window, in this dialog box, we will
be able to provide the co-ordinates of a node of the structure in the
main window to which we want to connect the piece being brought
from the wizard.

If there isn’t any existing structure, this box is a means of

specifying any distances along X, Y and Z axes by which we want the
unit (being brought from the Wizard) to be shifted.
3-42 Tutorial 3

In our case, since we do not have an existing structure in the main

window, nor do we wish to shift the unit by any amount, let us
simply click on the OK button.

Figure 3. 45

The model will now be transferred to the main window.

Figure 3. 46
 Tutorial 3 3-43
If you want to proceed with assigning the remainder of the data,
go to section 3.6.2.

Instead, if you wish to explore the remaining methods of creating this

model, the current structure will have to be entirely deleted. This can be
done using the following procedure.

From the Select menu, choose By All | All Geometry option. The
entire structure will be highlighted. Hit the key on your
keyboard. A message box shown below will appear. Click on the
OK button.

Figure 3. 47

As we click on the OK button, the following message box appears. Let us

say Yes. The message box will be dismissed and the entire structure will
be deleted.

Figure 3. 48
3-44 Tutorial 3

Creating the Plates - Method 4

Steps:

The STAAD.Pro GUI contains a facility for generating a mesh of

elements from a boundary (or superelement) defined by a set of
corner nodes. This facility is in addition to the one we saw in
Method 3. The boundary has to form a closed surface and has to be
a plane, though that plane can be inclined to any of the global
planes.

1. The first step in defining the boundary is selecting the corner

nodes. If these nodes do not exist, they must be created before they can be
selected. So, either click on the Snap Node/Quad Plates
icon or select Geometry | Snap/Grid Node | Plate | Quad menu option
as shown in the figures below.

Figure 3. 49
 Tutorial 3 3-45

Figure 3. 50

2. A Snap Node/Plate dialog box appears in the data area on the right
side of the screen. (We have already seen this dialog box in
methods 1 and 2.) As before, let us select the Linear tab. In our
structure, the elements lie in the X-Z plane. So, in this dialog box,
let us choose X-Z as the Plane of the grid. The size of the model
that can be drawn at any time is controlled by the number of
Construction Lines to the left and right of the origin of axes, and
the Spacing between adjacent construction lines. All that we are
interested in is the 4 corner nodes of the super-element. So, let us
set 1 as the number of lines to the right of the origin along X and Z, and a
spacing of 6m between lines along X and 4m along Z.
3-46 Tutorial 3

Figure 3. 51
 Tutorial 3 3-47
The main drawing area will now look similar to the one shown below.

Figure 3. 52
3-48 Tutorial 3

3. To start creating the nodes, let us first activate the Snap

Node/Plate button by clicking on it. Holding the ‘Ctrl’ key down, click at
the four corners of the grid as shown below. Those four
points represent the four corners of our slab and are (0, 0, 0), (6, 0,
0), (6, 0, 4), and (0, 0, 4). In fact, keeping the ‘Ctrl’ key pressed
and clicking at points on the grid successively, is a way of creating new
nodes without connecting those nodes with beams or plates. If the ‘Ctrl’
key weren’t kept pressed, the nodes would become
connected.

Figure 3. 53

It is worth noting that the purpose of the previous four steps was to merely
create the four nodes. Consequently, any of the several methods available
in the program could have been used to create
those nodes. We could have typed the data into the editor, or in the grid
tables of the Geometry-Plate page control area, or even used
the Snap Grid/Node – Beam option of the Geometry menu from the
top of the screen to graphically create the points.
 Tutorial 3 3-49
4. Let us now Close the Snap Node/Plate dialog box as shown below.

Figure 3. 54

We are now ready to utilize the second method available in the

program for mesh generation.
3-50 Tutorial 3

5. For this, either click on the Generate Surface Meshing icon or go

to Geometry | Generate Surface Meshing menu option as shown
below.

Figure 3. 55

Figure 3. 56
 Tutorial 3 3-51
6. We now have to select the points which form the boundary of the
superelement from which the individual elements will be created.
The four points we just created are those four points. So, let us
click at the four node points in succession as shown below. Lastly, close
the loop by clicking at the start node (or the first clicked
point) again.

Figure 3. 57

As we click at the start node the second time, the following dialog box
comes up. Let us choose the Quadrilateral Meshing option
and click on the OK button.

Figure 3. 58
3-52 Tutorial 3

7. The Select Meshing Parameters dialog box (as we saw earlier in

Method 3), comes up. Notice that this time however, the data for
the four corners is automatically filled in. The program used the
coordinates of the four nodes we selected to define A, B, C, and D.
Provide the Bias and the Divisions of the model as shown in the figure
below. Click on the Apply button.

Figure 3. 59

As we click on the Apply button, our model will appear in the

drawing area as the one shown below. Click on the button to
exit the mesh generating mode.

Figure 3. 60
 Tutorial 3 3-53

3.6.2 Changing the input units of length

As a matter of convenience, for specifying element properties for

our structure, it is simpler if our length units are centimeter instead
of meter. This will require changing the current length units of
input. The command to be generated is:

UNIT CM KN

Steps:

1. Click on the Input Units icon from the appropriate toolbar.

Figure 3. 61

Alternatively, one may select the Tools | Set Current Input Unit
menu option as shown below.

Figure 3. 62
3-54 Tutorial 3

2. In either case, the following dialog box comes up. Set the Length
Units to Centimeter and click on the OK button.

Figure 3. 63
 Tutorial 3 3-55

3.6.3 Specifying Element Properties

Just as properties are assigned to members, properties must be

assigned to plate elements too. The property required for plates is
the plate thickness (or the thickness at each node of elements if the slab
has a varying thickness).

The corresponding command which should be generated in the

STAAD command file is:

ELEMENT PROPERTY
1 TO 6 THICKNESS 30

Steps:

1. Click on the Property Page icon located on the Structure Tools

toolbar.

Figure 3. 64
3-56 Tutorial 3

Alternatively, one may go to the General | Property page from the left
side of the screen as shown below.

Figure 3. 65
 Tutorial 3 3-57
2. In either case, the Properties dialog box comes up as shown
below. Plate thickness is specified through the dialog box available under
the Thickness button.

Figure 3. 66
3-58 Tutorial 3

3. The dialog box shown below comes up. Let us provide the plate
thickness as 30cm. Notice that the field called Material is presently on the
checked mode. If we keep it that way, the material
properties of concrete (E, Poisson, Density, Alpha, etc.) will be
assigned along with the plate thickness. The material property values
so assigned will be the program defaults. (To see those default values,
click on the Materials button in the dialog box
shown in the previous figure.) Since we want to assign just the default
values, let us keep the Material box in the checked mode
itself. Then, click on the Add button followed by the Close button
as shown below.

Figure 3. 67
 Tutorial 3 3-59
At this point, the Properties dialog box will look as shown below.

Figure 3. 68

4. Since we want the thickness to be applied to all elements of the

structure, let us select the Assignment Method called Assign To
View and then click on the Assign button as shown in the above figure.

As we click on the Assign button, the following message box

comes up. Let us click on the Yes button to confirm our choice.

Figure 3. 69
3-60 Tutorial 3

The structure will now look as shown below.

Figure 3. 70

Click anywhere in the drawing area to un-highlight the selected

entities. We do this only as a safety precaution. When an entity is
highlighted, clicking on any Assign option is liable to cause an
undesired attribute to be assigned to that entity.
 Tutorial 3 3-61

3.6.4 Specifying Material Constants

In Section 3.6.3, we kept the Material check box “on” while

assigning the element properties. Consequently, the material
constants (E, Density, Poisson’s Ratio, etc.) of concrete got
assigned to the plates along with the properties, and the following
commands were generated in the command file:

UNIT METER KN
CONSTANTS
E 2.17185e+007 MEMB 1 TO 6
POISSON 0.17 MEMB 1 TO 6
DENSITY 23.5616 MEMB 1 TO 6
ALPHA 1e-005 MEMB 1 TO 6

Hence, there is no longer a need to assign the constants separately.

However, if we hadn’t assigned them as before, we could go to the menu
option Commands | Material Constants and assign them
explicitly as shown in the figure below.

Figure 3. 71
3-62 Tutorial 3

3.6.5 Specifying Supports

The slab is fixed-supported along the entire length of two of its

sides. However, when modelled as plate elements, the supports can
be specified only at the nodes along those edges, and not at any
point between the nodes. It hence becomes apparent that if one is
keen on better modelling the edge conditions, the slab would have
to be modelled using a larger number of elements.

In our case, the commands we need to generate are:

SUPPORTS
1 2 4 5 7 10 FIXED

Steps:

1. To create supports, click on the Support Page icon located in the

Structure Tools toolbar as shown below.

Figure 3. 72
 Tutorial 3 3-63
Alternatively, one may go to the General | Support Page from the
left side of the screen.

Figure 3. 73
3-64 Tutorial 3

2. In either case, the Supports dialog box comes up as shown in the

next figure.

3. For easy identification of the nodes where we wish to place the

supports, let us turn the Node Numbers on.

4. Since we already know that nodes 1, 2, 5, 7, 4 and 10 are to be

associated with the Fixed support, using the Nodes Cursor ,

select these nodes.

5. Then, click on the Create button in the Supports dialog box as

shown below.

Figure 3. 74
 Tutorial 3 3-65
6. The dialog box shown below comes up. The Fixed tab happens to
be the default which is convenient for this case. Click on the
Assign button as shown below.

Figure 3. 75

It is important to understand that the Assign button is active

because of what we did in step 4 earlier. Had we not selected the nodes
before reaching this point, this option would not have been active.
3-66 Tutorial 3

After the supports have been assigned, the structure will look like the one
shown below.

Figure 3. 76
 Tutorial 3 3-67

3.6.6 Specifying Primary Load Cases

Three primary load cases have to be created for this structure. Details
of these load cases are available at the beginning of this tutorial. The
corresponding commands to be generated are listed below.

UNIT METER KG
LOAD 1 DEAD LOAD
SELF Y -1.0

LOAD 2 EXTERNAL PRESSURE LOAD

ELEMENT LOAD
1 TO 6 PR GY -300

LOAD 3
TEMPERATURE LOAD
1 TO 6 TEMP 40 30

Steps:

1. To create loads, click on the Load Page icon located on the

Structure Tools tool bar.

Figure 3. 77
3-68 Tutorial 3

Alternatively, one may go to the General | Load Page from the left side of
the screen.

Figure 3. 78

2. Notice that the pressure load value listed in the beginning of this
tutorial is in KN and meter units. Rather than convert that value to
the current input units, we will conform to those units. The current
input units, which we last set while specifying THICKNESS was
CENTIMETER. We have to change the force unit to Kilogram and
the length units to Meter. To change the units, as before, click on
the Input Units icon from the top toolbar, or select the Tools |
Set Current Input Unit menu option from the top menu bar. In the
Set Current Input Units dialog box that comes up, specify the
length units as meter and the force units as Kilogram.
 Tutorial 3 3-69
LOAD CASE 1

3. A window titled “Load” appears on the right-hand side of the

screen. To initiate the first load case, highlight Load Cases Details
and click on the Add button.

Figure 3. 79

4. The Add New Load Cases dialog box comes up. The drop-down list
box against Loading Type is available in case we wish to associate
the load case we are creating with any of the ACI, AISC or IBC
definitions of Dead, Live, Ice, etc. This type of association needs
to be done if we intend to use the program's facility for
automatically generating load combinations in accordance with those
codes.
Notice that there is a check box called Reducible per UBC/IBC.
This feature becomes active only when the load case is assigned a
Loading Type called Live at the time of creation of that case.
Please refer to STAAD.Pro 2004 Release Report for further details.

As we do not intend to use the automatic load combination

generation option, we will leave the Loading Type as None. Enter
DEAD LOAD as the Title for Load Case 1 and click on Add.
3-70 Tutorial 3

Figure 3. 80

The newly created load case will now appear under the Load Cases Details
in the Load dialog box.

Figure 3. 81

5. To generate and assign the first load type, highlight DEAD LOAD.
You will notice that the Add New Load Items dialog box shows
more options now.

Figure 3. 82
 Tutorial 3 3-71
6. In the Add New Load Items dialog box, select the Selfweight Load
option under the Selfweight item. Specify the Direction as Y, and the
Factor as -1.0. The negative number signifies that the
selfweight load acts opposite to the positive direction of the global axis (Y
in this case) along which it is applied. Click on the Add button. The
selfweight load is applicable to every member of the
structure, and cannot be applied on a selected list of members.

Figure 3. 83
3-72 Tutorial 3

LOAD CASE 2

7. Next, let us initiate the creation of the second load case which is a
pressure load on the elements. To do this, highlight Load Cases
Details. In the Add New Load Cases dialog box, once again, we are not
associating the load case we are about to create with any code based
Loading Type and so, leave that box as None. Specify the
Title of the second load case as EXTERNAL PRESSURE LOAD
and click on the Add button.

Figure 3. 84

To generate and assign the second load type, highlight

EXTERNAL PRESSURE LOAD.

Figure 3. 85
 Tutorial 3 3-73
8. In the Add New Load Items dialog box, select the Pressure on
Full Plate option under the Plate Loads item enables the load to be
applied on the full area of the element. (The Concentrated Load is
for applying a concentrated force on the element. The Trapezoidal
and Hydrostatic options are for defining pressures with intensities
varying from one point to another. The Partial Plate Pressure
Load is useful if the load is to be applied as a “patch” on a small
localised portion of an element.)

Let us keep our focus on the Pressure on Full Plate option.

Provide -300kg/m2 for W1 (Force), GY as the Direction and click on the
Add button followed by the Close button.

Figure 3. 86
3-74 Tutorial 3

9. Since the pressure load is to be applied on all the elements of the

model, the easiest way to do that is to set the Assignment Method to
Assign To View. Then, click on the Assign button in the Load
dialog box as shown below.

Figure 3. 87

After the load has been assigned, the model will look as shown below.

Figure 3. 88
 Tutorial 3 3-75
LOAD CASE 3

10. Next, let us create the third load case which is a temperature load.
The initiation of a new load case is best done using the procedure
explained in step 7. In the dialog box that comes up, let us specify
the Title of the third load case as TEMPERATURE LOAD and
click on the Add button.

Figure 3. 89

To generate and assign the third load type, as before, highlight

TEMPERATURE LOAD.

11. Temperature Loads are created from the input screens available
under the Temperature option in the Add New Load Items dialog box.
3-76 Tutorial 3

12. In the Add New Load Items dialog box, make sure that the
Temperature item is selected under the Temperature Loads
option. Then, provide 40 as the Temperature Change for Axial
Elongation and 30 as the Temperature Differential from Top to
Bottom and click on the Add button followed by the Close button.

Figure 3. 90

13. Since we intend to apply the temperature load on all the plates, as
before, choose Assign To View and click on the Assign button in
the Loads dialog box (see step 9 for explanation).
 Tutorial 3 3-77

3.6.7 Creating load combinations

The specifications at the beginning of this tutorial require us to create

two combination cases. The commands required are:

LOAD COMBINATION 101 CASE 1 + CASE 2

1 1.0 2 1.0
LOAD COMBINATION 102 CASE 1 + CASE 3
1 1.0 3 1.0

Steps:

LOAD COMBINATION 101

1. To initiate and define load case 4 as a load combination, once

again, highlight the Load Cases Details option. In the Add New Load
Cases dialog box, click on the Define Combinations option
from the left-hand side. Enter the Load No: as 101 and the Title as
CASE 1 + CASE 2.

Figure 3. 91
3-78 Tutorial 3

2. Next, in the Define Combinations box, select load case 1 from the
left side list box and click on the button. Repeat this with load
case 2 also. Load cases 1 and 2 will appear in the right side list box
as shown in the figure below. (These data indicate that we are
adding the two load cases with a multiplication factor of 1.0 and that the
load combination results would be obtained by algebraic summation of
the results for individual load cases.) Finally, click on the Add button.

Figure 3. 92

Case 101 has now been created.

 Tutorial 3 3-79
LOAD COMBINATION 102

3. To initiate and define load case 5 as a load combination, as before,

enter the Load No: as 102 and the Title as CASE 1 + CASE 3.

Next, repeat step 2 except for selecting load cases 1 and 3 instead
of cases 1 and 2.

Figure 3. 93

Thus, load 102 is also created.

3-80 Tutorial 3

If we change our mind about the composition of any existing

combination case, we can select the case we want to alter, and
make the necessary changes in terms of the constituent cases or their
factors.

Figure 3. 94

Let us exit this dialog box by clicking on the Close button.

It is also worth noting that as load cases are created, a facility for quickly
switching between the various cases becomes available at the top of the
screen in the form of a load case selection box as
shown below.

Figure 3. 95
 Tutorial 3 3-81
We have now completed the task of creating all load cases.

Let us once again save our model by pulling down the File menu and
selecting the Save command or by holding the ‘Ctrl’ key and pressing
the ‘S’ key.
3-82 Tutorial 3

3.6.8 Specifying the analysis type

The analysis type we are required to do is a linear static type. We will

also obtain a static equilibrium report. This requires the
command:

PERFORM ANALYSIS PRINT STATICS CHECK

Steps:

1. To specify the Analysis command, first go to Analysis/Print Page

from the left side of the screen.

Figure 3. 96
 Tutorial 3 3-83
2. In the Analysis/Print Commands dialog box that appears, the
instruction for specifying a linear elastic type analysis is provided using
the Perform Analysis tab. To obtain the static equilibrium
report, check the Statics Check print option. (In response to this option,
a report consisting of the summary of applied loading and
summary of support reactions, for each load case, will be produced
in the STAAD output file. See section 3.10 for information on
viewing this report).

Figure 3. 97

Finally, click on the Add button followed by the Close button.

3-84 Tutorial 3

The Analysis dialog box in the data area with the newly added
instruction will look as shown below.

Figure 3. 98

Let us save the data once again using the File | Save option.
 Tutorial 3 3-85

3.6.9 Specifying post-analysis print commands

Two types of element results can be requested: a) ELEMENT

STRESSES at the centroid or any point on the element surface b)
the element forces at the nodes. The former consists of stresses and
moments per unit width, as explained in sections 1.6.1 and 3.41 of
the STAAD Technical Reference Manual. The latter consists of the
3 forces and 3 moments at each node of the elements in the global
axis system (see section 3.41 for details).

We would like to obtain both these results. We will also set the
units in which these results are printed to KN and Meter for
element stresses and Kg and Meter for element forces. This
requires the specification of the following commands:

UNIT METER KN
PRINT ELEMENT STRESSES LIST 3
UNIT KG METER
PRINT ELEMENT FORCE LIST 6

These results will be written in the STAAD output file and can be viewed
using the procedure explained in section 3.10.

Steps:

1. Go to Tools | Set Current Input Unit menu option. Set the length
and force units to Meter and Kilo Newton respectively.

2. The dialog box for requesting element results is available in the

Post-Print sub-page of the Analysis | Print page.

Click on the Define Commands button in the data area on the right
hand side of the screen.
3-86 Tutorial 3

Figure 3. 99

3. In the Analysis/Print Commands dialog box that appears, select the

Element Forces/Stresses tab. Choose the Print Element Stresses
option and click on the Add button followed by the Close button.

Figure 3. 100
 Tutorial 3 3-87
4. Again, go to Tools | Set Current Input Unit menu option. Set the
length and force units to Meter and Kilogram respectively.

Then, repeat steps 2 and 3. In step 3, select the Print Element

Forces option and click on the Add button followed by the Close
button.

At this point, the Post Analysis Print dialog box will look as shown
below.

Figure 3. 101
3-88 Tutorial 3

5. To associate the PRINT ELEMENT STRESSES command with

element 3, first select the command as shown in the previous

figure. Then, using the Plates Cursor , click on element no.

3.

As we select the plate, the Assignment Method automatically

becomes Assign to Selected Plates. Click on the Assign button as shown
below.

Figure 3. 102

6. To associate the PRINT ELEMENT FORCE command with element

6, repeat step 5 except for selecting element no. 6 in the place of
element no. 3.

We have now completed the tasks of assigning the input for this model.
Let us save the file one last time using the File | Save
option.
 Tutorial 3 3-89

3.7 Viewing the input command file

Let us now take a look at the data that has been written into the file that we
just saved earlier. As we have seen in the previous
tutorials, while the model is being created graphically, a
corresponding set of commands describing that aspect of the model
is being simultaneously written into a command file which is a
simple text file. An abstract of those commands was also
mentioned under the title “commands to be generated are . .” at the
beginning of each section of this tutorial.

The contents of that text file can be viewed in its entirety either by
clicking on the STAAD Editor icon or, by going to the Edit menu and
choosing Edit Input Command File as shown below.

Figure 3. 103

Figure 3. 104
3-90 Tutorial 3

A new window will open up with the data listed as shown here:

Figure 3. 105

This window and the facilities it contains is known as the STAAD Editor.

We could make modifications to the data of our structure in this

Editor if we wish to do so. Let us Exit the Editor without doing so
by selecting the File | Exit menu option of the editor window (not
the File | Exit menu of the main window behind the editor
window).

Instead of using the graphical methods explained in the previous

sections, we could have created the entire model by typing these
specific commands into the editor. This was one of the methods
mentioned in section 3.1 of this tutorial. If you would like to
understand that method, proceed to the next section. If you want to
skip that part, proceed to section 3.9 where we perform the analysis
on this model.
 Tutorial 3 3-91

3.8 Creating the model using the command file

Let us now use the command file method to create the model for
the above structure. The commands used in the command file are
described later in this section.

The STAAD.Pro command file may be created using the built-in editor,
the procedure for which is explained further below in this
section. Any standard text editor such as Notepad or WordPad may also be
used to create the command file. However, the STAAD.Pro command file
editor offers the advantage of syntax checking as we type the commands.
The STAAD.Pro keywords, numeric data,
comments, etc. are displayed in distinct colors in the STAAD.Pro
editor. A typical editor screen is shown below to illustrate its general
appearance.

Figure 3. 106
3-92 Tutorial 3

To access the built-in editor, first start the program using the
procedure explained in Section 3.3. Next, follow step 1 of Section 3.4 (also,
see Figures below).

Figure 3. 107

You will then encounter the dialog box shown below. In that dialog
box, choose Open STAAD Editor.

Figure 3. 108
 Tutorial 3 3-93
At this point, the editor screen will open as shown below.

Figure 3. 109

Delete all the command lines displayed in the editor window and
type the lines shown in bold below (You don’t have to delete the
lines if you know which to keep and where to fill in the rest of the
commands). The commands may be typed in upper or lower case
letters. Usually the first three letters of a keyword are all that are needed
-- the rest of the letters of the word are not required. The required letters
are underlined. (“SPACE” = “SPA” = “space” = “spa”)
3-94 Tutorial 3

Actual input is shown in bold lettering followed by explanation.

STAAD SPACE SLAB SUPPORTED ALONG 2 EDGES

Every input has to start with the word STAAD. The word SPACE
signifies that the structure is a space frame structure (3-D) and the
geometry is defined through X, Y and Z coordinates.

UNIT METER KN

Specifies the unit to be used for data to follow.

JOINT COORDINATES
1000;2200;3202;4002
5400;6402;7600;8602
9 2 0 4 ; 10 0 0 4 ; 11 4 0 4 ; 12 6 0 4

Joint number followed by X, Y and Z coordinates are provided

above. Semicolon signs (;) are used as line separators. That enables
us to provide multiple sets of data on one line. For example, node 6
has (X, Y, Z) coordinates of (4, 0, 2).

ELEMENT INCIDENCES SHELL

1 1 2 3 4 ; 2 2 5 6 3 ; 3 5 7 8 6 ; 4 4 3 9 10 ;
5 3 6 11 9 ; 6 6 8 12 11

The incidences of elements are defined above. For example,

element 3 is defined as connected between the nodes 5, 7, 8 and 6.

UNIT CM KN
ELEMENT PROPERTY
1 TO 6 THICKNESS 30

The length unit is changed from meter to centimeter. Element

properties are then provided by specifying that the elements are 30 cm
thick.
 Tutorial 3 3-95
UNIT METER KN
CONSTANTS
E 2.17185e+007 ALL
POISSON 0.17 ALL
DENSITY 23.5616 ALL
ALPHA 1e-005 ALL

Material constants, which are E (modulus of elasticity), Density,

Poisson’s Ratio and Alpha, are specified following the command
CONSTANTS. Prior to this, the input units are changed to Meter and
KN.

SUPPORTS
1 2 4 5 7 10 FIXED

Joints 1, 2, 4, 5, 7 and 10 are defined as fixed supported. This will cause

all 6 degrees of freedom at these nodes to be restrained.

UNIT KG
LOAD 1 DEAD LOAD

Force units are changed from KN to KG to facilitate the input of loads.

Load case 1 is then initiated along with an accompanying title.

SELFWEIGHT Y -1

Load case 1 consists of selfweight of the structure acting in the

global Y direction with a factor of -1.0. Since global Y is vertically
upward, the factor of -1.0 indicates that this load will act
downwards.

LOAD 2 EXTERNAL PRESSURE LOAD

Load case 2 is initiated along with an accompanying title.

ELEMENT LOAD
1 TO 6 PR GY -300
3-96 Tutorial 3

Load 2 is a pressure load on the elements. A uniform pressure of

300Kg/m2 is applied on all the elements. GY indicates that the load
is in the global Y direction. The negative sign (-300) indicates that
the load acts opposite to the positive direction of global Y.

LOAD 3 TEMPERATURE LOAD

Load case 3 is initiated along with an accompanying title.

TEMPERATURE LOAD
1 TO 6 TEMP 40 30

Load 3 is a temperature load. All the 6 elements are subjected to a in-

plane temperature increase of 40 degrees and a temperature
variation across the thickness of 30 degrees. This increase is in the same
temperature units as the Alpha value specified earlier under
CONSTANTS.

LOAD COMB 101 CASE 1 + CASE 2

1 1.0 2 1.0

Load combination 101 is initiated along with an accompanying title.

Load cases 1 and 2 are individually factored by a value of 1.0, and the
factored values are combined algebraically.

LOAD COMB 102 CASE 1 + CASE 3

1 1.0 3 1.0

Load combination 102 is initiated along with an accompanying title.

Load cases 1 and 3 are individually factored by a value of 1.0, and the
factored values are combined algebraically.

PERFORM ANALYSIS PRINT STATICS CHECK

The above command instructs the program to proceed with the

analysis. A static equilibrium report is also requested with the help
of the words PRINT STATICS CHECK.

UNIT METER KN
PRINT ELEMENT STRESS LIST 3
 Tutorial 3 3-97
The stresses and unit width moments are requested at the centroid
of element 3 in KN and Meter units.

UNIT KG METER
PRINT ELEMENT FORCE LIST 6

The forces and moments for all 6 d.o.f at the corner nodes of
element 6 are requested in KG and Meter units.

FINISH

This command terminates the STAAD run. Let

us save the file and exit the editor.

3-98 Tutorial 3

3.9 Performing the analysis and design

In order to obtain the displacements, forces, stresses and reactions

in the structure due to the applied loads, the model has to be
analyzed. If the pass-fail status of the members and elements per the
requirements of steel and concrete codes is to be determined, that
involves a process called design. Both these processes are launched
using the Run Analysis option from the Analyze menu.

Figure 3. 110

If the structure has not been saved after the last change was made, you
should save the structure first by using the Save command
from the File menu.

When you select the Run Analysis option from the Analyze menu, the
following dialog box appears:

Figure 3. 111

We are presented with the choice of 2 engines : the STAAD engine and the
STARDYNE Advanced Analysis engine. The STARDYNE Analysis
engine is suitable for advanced problems such as
Buckling Analysis, Modal Extraction using various methods, etc.
However, if the calculations call for steel or concrete design, UBC
 Tutorial 3 3-99
load generation, etc., we have to select the STAAD engine. For
this problem, let us use the STAAD engine.

Then, click on the Run Analysis button.

As the analysis progresses, several messages appear on the screen

as shown in the next figure.

Figure 3. 112
At the end of these calculations, two activities take place. a) A
Done button becomes active b) three options become available at the
bottom left corner of this information window.

Figure 3. 113
3-100 Tutorial 3

These options are indicative of what will happen after we click on the
Done button.

The View Output File option allows us to view the output file
created by STAAD. The output file contains the numerical results
produced in response to the various input commands we specified during
the model generation process. It also tells us whether any
errors were encountered, and if so, whether the analysis and design
was successfully completed or not. Section 3.10 (also, see section
1.9) offers additional details on viewing and understanding the
contents of the output file.

The Go To Post Processing Mode option allows us to go to

graphical part of the program known as the Post-processor. This is where
one can extensively verify the results, view the results
graphically, plot result diagrams, produce reports, etc. Section 3.11
explains the Post processing mode in greater detail.

The Stay in Modelling Mode lets us continue to be in the Model

generation mode of the program (the one we currently are in) in
case we wish to make further changes to our model.
 Tutorial 3 3-101

3.10 Viewing the output file

During the analysis stage, an output file containing results,

warnings and messages associated with errors if any in the output,
is produced. This file has the extension .anl and may be viewed
using the output viewer. Section 1.9 of this manual contains
information on viewing this file.

In Sections 3.6.8 and 3.6.9, we had provided instructions to the

program to write some very specific results in the output file. Let
us examine those results.

PRINT STATICS CHECK

This instruction was provided so that we could view a report

indicating if the structure is in equilibrium for the various load
cases. If we scroll down the output file, we will see information
which looks like the following:

***TOTAL APPLIED LOAD ( KG METE ) SUMMARY (LOADING 1 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = -17298.83
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 34597.65 MY= 0.00 MZ= -51896.48

***TOTAL REACTION LOAD( KG METE ) SUMMARY (LOADING 1)

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = 17298.83
SUMMATION FORCE-Z = 0.00
SUMMATION OF MOMENTS AROUND THE ORIGIN-
MX= -34597.65 MY= 0.00 MZ= 51896.48
MAXIMUM DISPLACEMENTS ( CM /RADIANS) (LOADING 1)
MAXIMUMS AT NODE
3-102 Tutorial 3

X = 0.00000E+00 0
Y = -3.20681E-01 12
Z = 0.00000E+00 0
RX = 9.80406E-04 12
RY = 0.00000E+00 0
RZ = -6.49355E-04 9

For each primary load case, the report consists of:

a. Summary of total applied loads for all 6 degrees of

freedom, with moments calculated about the origin of the
coordinate system (0, 0, 0)

b. Summary of total reactions from the supports of the

structure, with moments calculated about the origin of the
coordinate system (0, 0, 0)

c. Maximum displacements (3 translations and 3 rotations) in

the structure induced by this load case

Each of the 6 terms of item (a) must be equal and opposite to the
corresponding term of item (b). A failure to meet this criteria
would mean the analysis results (for a linear elastic analysis) may
be erroneous. Factors such as instability conditions or improperly
applied loads can cause the equilibrium check to fail.

It is quite important to examine the maximum displacements since they

tell us whether the deformations are within tolerable limits.

Since the information presented above is for load case 1, and since load
case 1 is the selfweight of the structure, we can conclude that the structure
weighs 17298.83 Kgs.
 Tutorial 3 3-103
STRESSES FOR ELEMENT 3

This information consists of the stress and “moment over unit width”
values at the centroid of element 3. A typical sample is presented
below.

ELEMENT STRESSES FORCE, LENGTH UNITS = KN METE

----------------
FORCE OR STRESS = FORCE/UNIT WIDTH/THICK,
MOMENT = FORCE-LENGTH/UNIT WIDTH

ELEMENT LOAD SQX SQY MX MY MXY

VONT VONB SX SY SXY

3 1 -18.13 72.86 -3.96 -20.42 -3.35

1308.63 1308.63 0.00 0.00 0.00
TOP : SMAX= -220.33 SMIN= -1404.81 TMAX= 592.24 ANGLE= -11.1
BOTT: SMAX= 1404.81 SMIN= 220.33 TMAX= 592.24 ANGLE= -11.1

These terms are explained in Section 1.6.1 of the STAAD

Technical Reference Manual in elaborate detail. Example problem
18 of the Examples Manual explains the method involved in
calculating the principal stresses SMAX, SMIN and TMAX.
3-104 Tutorial 3

FORCES FOR ELEMENT 6

This information consists of the force and moment values at each

of the 4 corner nodes of element 6. A typical sample is presented
below.

ELEMENT FORCES FORCE,LENGTH UNITS= KG METE

--------------
JOINT FX FY FZ MX MY MZ

ELE.NO. 6 FOR LOAD CASE 1

6 0.0000E+00 4.5323E+02 0.0000E+00 -1.1313E+03 0.0000E+00 7.9082E+02
8 0.0000E+00 5.0615E+02 0.0000E+00 -3.2047E+02 0.0000E+00 2.3981E+02
12 0.0000E+00 -7.2078E+02 0.0000E+00 1.0346E-03 0.0000E+00 -1.3733E-03
11 0.0000E+00 -2.3860E+02 0.0000E+00 -4.6697E+02 0.0000E+00 -6.0136E+02

The corner forces are in the global coordinate system. These values may be
used to create a free body diagram of the element and
verify that the element is in equilibrium. In this case for example, the FX
and FZ forces are zero, and sum of the FY forces is also
zero.

The complete text of the output file is shown in the next few pages.
 Tutorial 3 3-105

****************************************************
* *
* STAAD.Pro *
* Version Bld *
* Proprietary Program of *
* Research Engineers, Intl. *
* Date= *
* Time= *
* *
* USER ID: *
****************************************************

1. STAAD SPACE SLAB SUPPORTED ALONG 2 EDGES

2. START JOB INFORMATION
3. ENGINEER DATE
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 2 2 0 0; 3 2 0 2; 4 0 0 2; 5 4 0 0; 6 4 0 2; 7 6 0 0; 8 6 0 2
9. 9 2 0 4; 10 0 0 4; 11 4 0 4; 12 6 0 4
10. ELEMENT INCIDENCES SHELL
11. 1 1 2 3 4; 2 2 5 6 3; 3 5 7 8 6; 4 4 3 9 10; 5 3 6 11 9; 6 6 8 12 11
12. UNIT CM KN
13. ELEMENT PROPERTY
14. 1 TO 6 THICKNESS 30
15. DEFINE MATERIAL START
16. ISOTROPIC CONCRETE
17. E 2171.85
18. POISSON 0.17
19. DENSITY 2.35616E-005
20. ALPHA 1E-005
21. DAMP 0.05
22. END DEFINE MATERIAL
23. CONSTANTS
24. MATERIAL CONCRETE MEMB 1 TO 6
25. SUPPORTS
26. 1 2 4 5 7 10 FIXED
27. LOAD 1 DEAD LOAD
28. SELFWEIGHT Y -1
29. LOAD 2 EXTERNAL PRESSURE LOAD
30. UNIT METER KG
31. ELEMENT LOAD
32. 1 TO 6 PR GY -300
33. LOAD 3 TEMPERATURE LOAD
34. TEMPERATURE LOAD
35. 1 TO 6 TEMP 40 30
36. LOAD COMB 101 CASE 1 + CASE 2
37. 1 1.0 2 1.0
38. LOAD COMB 102 CASE 1 + CASE 3
39. 1 1.0 3 1.0
40. PERFORM ANALYSIS PRINT STATICS CHECK

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS/MEMBER+ELEMENTS/SUPPORTS = 12/ 6/ 6

ORIGINAL/FINAL BAND-WIDTH= 8/ 5/ 36 DOF
TOTAL PRIMARY LOAD CASES = 3, TOTAL DEGREES OF FREEDOM = 72
SIZE OF STIFFNESS MATRIX = 3 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.1/ 3521.0 MB, EXMEM = 461.2 MB

STATIC LOAD/REACTION/EQUILIBRIUM SUMMARY FOR CASE NO. 1

DEAD LOAD

***TOTAL APPLIED LOAD ( KG METE ) SUMMARY (LOADING 1 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = -17298.83
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 34597.66 MY= 0.00 MZ= -51896.48
3-106 Tutorial 3

***TOTAL REACTION LOAD( KG METE ) SUMMARY (LOADING 1 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = 17298.83
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= -34597.66 MY= 0.00 MZ= 51896.48

MAXIMUM DISPLACEMENTS ( CM /RADIANS) (LOADING 1)

MAXIMUMS AT NODE
X = 0.00000E+00 0
Y = -3.20681E-01 12
Z = 0.00000E+00 0
RX= 9.80406E-04 12
RY= 0.00000E+00 0
RZ= -6.49355E-04 9

STATIC LOAD/REACTION/EQUILIBRIUM SUMMARY FOR CASE NO. 2

EXTERNAL PRESSURE LOAD

***TOTAL APPLIED LOAD ( KG METE ) SUMMARY (LOADING 2 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = -7200.00
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 14400.00 MY= 0.00 MZ= -21600.00

***TOTAL REACTION LOAD( KG METE ) SUMMARY (LOADING 2 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = 7200.00
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= -14400.00 MY= 0.00 MZ= 21600.00

MAXIMUM DISPLACEMENTS ( CM /RADIANS) (LOADING 2)

MAXIMUMS AT NODE
X = 0.00000E+00 0
Y = -1.33471E-01 12
Z = 0.00000E+00 0
RX= 4.08058E-04 12
RY= 0.00000E+00 0
RZ= -2.70270E-04 9

STATIC LOAD/REACTION/EQUILIBRIUM SUMMARY FOR CASE NO. 3

TEMPERATURE LOAD

***TOTAL APPLIED LOAD ( KG METE ) SUMMARY (LOADING 3 )

SUMMATION FORCE-X = 0.00
SUMMATION FORCE-Y = 0.00
SUMMATION FORCE-Z = 0.00

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 0.00 MY= 0.00 MZ= 0.00

***TOTAL REACTION LOAD( KG METE ) SUMMARY (LOADING 3 )

SUMMATION FORCE-X = -0.01
SUMMATION FORCE-Y = 0.00
SUMMATION FORCE-Z = 0.02

SUMMATION OF MOMENTS AROUND THE ORIGIN-

MX= 0.00 MY= -0.10 MZ= 0.00
 Tutorial 3 3-107

MAXIMUM DISPLACEMENTS ( CM /RADIANS) (LOADING 3)

MAXIMUMS AT NODE
X = 2.01178E-01 12
Y = 8.97365E-01 12
Z = 1.66240E-01 11
RX= -3.51264E-03 12
RY= -2.41785E-04 11
RZ= 2.62398E-03 12

************ END OF DATA FROM INTERNAL STORAGE ************

41. UNIT METER KN

42. PRINT ELEMENT STRESSES LIST 3

ELEMENT STRESSES FORCE,LENGTH UNITS= KN METE

----------------

STRESS = FORCE/UNIT WIDTH/THICK, MOMENT = FORCE-LENGTH/UNIT WIDTH

ELEMENT LOAD SQX SQY MX MY MXY

VONT VONB SX SY SXY
TRESCAT TRESCAB

3 1 -18.13 72.86 -3.96 -20.42 -3.35

1308.63 1308.63 0.00 0.00 0.00
1404.81 1404.81
TOP : SMAX= -220.33 SMIN= -1404.81 TMAX= 592.24 ANGLE= -11.1
BOTT: SMAX= 1404.81 SMIN= 220.33 TMAX= 592.24 ANGLE= -11.1
2 -7.54 30.33 -1.65 -8.50 -1.39
544.67 544.67 0.00 0.00 0.00
584.70 584.70
TOP : SMAX= -91.70 SMIN= -584.70 TMAX= 246.50 ANGLE= -11.1
BOTT: SMAX= 584.70 SMIN= 91.70 TMAX= 246.50 ANGLE= -11.1
3 96.73 -59.42 -30.45 -14.83 18.43
10779.68 5300.82 -5044.81 -2309.43 3890.01
10912.04 5585.51
TOP : SMAX= 269.79 SMIN=-10642.25 TMAX= 5456.02 ANGLE= -34.9
BOTT: SMAX= 624.74 SMIN= -4960.77 TMAX= 2792.75 ANGLE= -36.2
101 -25.67 103.18 -5.61 -28.92 -4.74
1853.30 1853.30 0.00 0.00 0.00
1989.51 1989.51
TOP : SMAX= -312.03 SMIN= -1989.51 TMAX= 838.74 ANGLE= -11.1
BOTT: SMAX= 1989.51 SMIN= 312.03 TMAX= 838.74 ANGLE= -11.1
102 78.60 13.44 -34.41 -35.24 15.08
10642.95 5713.09 -5044.81 -2309.43 3890.01
11074.45 6408.55
TOP : SMAX= -923.15 SMIN=-11074.45 TMAX= 5075.65 ANGLE= -37.3
BOTT: SMAX= 1848.83 SMIN= -4559.72 TMAX= 3204.28 ANGLE= -32.1

**** MAXIMUM STRESSES AMONG SELECTED PLATES AND CASES ****

MAXIMUM MINIMUM MAXIMUM MAXIMUM MAXIMUM
PRINCIPAL PRINCIPAL SHEAR VONMISES TRESCA
STRESS STRESS STRESS STRESS STRESS

1.989513E+03 -1.107445E+04 5.456020E+03 1.077968E+04 1.107445E+04

PLATE NO. 3 3 3 3 3
CASE NO. 101 102 3 3 102

********************END OF ELEMENT FORCES********************

43. UNIT METER KG

3-108 Tutorial 3

44. PRINT ELEMENT FORCE LIST 6

ELEMENT FORCES FORCE,LENGTH UNITS= KG METE

--------------

**NOTE- IF A COMBINATION INCLUDES A DYNAMIC CASE OR IS AN SRSS OR ABS COMBINATION

THEN RESULTS CANNOT BE COMPUTED PROPERLY.
GLOBAL CORNER FORCES
JOINT FX FY FZ MX MY MZ

ELE.NO. 6 FOR LOAD CASE 1

6 0.0000E+00 4.5323E+02 0.0000E+00 -1.1313E+03 0.0000E+00 7.9082E+02
8 0.0000E+00 5.0615E+02 0.0000E+00 -3.2047E+02 0.0000E+00 2.3981E+02
12 0.0000E+00 -7.2078E+02 0.0000E+00 1.0346E-03 0.0000E+00 -1.3733E-03
11 0.0000E+00 -2.3860E+02 0.0000E+00 -4.6697E+02 0.0000E+00 -6.0136E+02
ELE.NO. 6 FOR LOAD CASE 2
6 0.0000E+00 1.8864E+02 0.0000E+00 -4.7087E+02 0.0000E+00 3.2915E+02
8 0.0000E+00 2.1067E+02 0.0000E+00 -1.3338E+02 0.0000E+00 9.9813E+01
12 0.0000E+00 -3.0000E+02 0.0000E+00 8.9143E-05 0.0000E+00 1.6633E-05
11 0.0000E+00 -9.9306E+01 0.0000E+00 -1.9436E+02 0.0000E+00 -2.5029E+02
ELE.NO. 6 FOR LOAD CASE 3
6 -2.9880E+05 6.6190E+02 -3.0717E+05 6.3684E+03 2.7912E+03 -5.5444E+03
8 3.0633E+05 -9.9013E+02 -3.2773E+05 4.3052E+03 -3.7431E+03 4.3521E+03
12 3.2019E+05 4.6301E-03 3.2019E+05 -6.0036E+03 4.0162E-03 6.0036E+03
11 -3.2773E+05 3.2822E+02 3.1471E+05 -4.0135E+03 9.5183E+02 -2.8311E+03
ELE.NO. 6 FOR LOAD CASE 101
6 0.0000E+00 6.4187E+02 0.0000E+00 -1.6022E+03 0.0000E+00 1.1200E+03
8 0.0000E+00 7.1681E+02 0.0000E+00 -4.5385E+02 0.0000E+00 3.3963E+02
12 0.0000E+00 -1.0208E+03 0.0000E+00 3.8188E-04 0.0000E+00 -9.6018E-05
11 0.0000E+00 -3.3790E+02 0.0000E+00 -6.6133E+02 0.0000E+00 -8.5165E+02
ELE.NO. 6 FOR LOAD CASE 102
6 -2.9880E+05 1.1151E+03 -3.0717E+05 5.2371E+03 2.7912E+03 -4.7536E+03
8 3.0633E+05 -4.8398E+02 -3.2773E+05 3.9847E+03 -3.7431E+03 4.5919E+03
12 3.2019E+05 -7.2078E+02 3.2019E+05 -6.0036E+03 4.0162E-03 6.0036E+03
11 -3.2773E+05 8.9625E+01 3.1471E+05 -4.4804E+03 9.5183E+02 -3.4325E+03
45. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= TIME= ****

************************************************************
* For questions on STAAD.Pro, please contact *
* Research Engineers Offices at the following locations *
* *
* Telephone Email *
* USA: +1 (714)974-2500 [email protected] *
* CANADA +1 (905)632-4771 [email protected] *
* CANADA +1 (604)629 6087 [email protected] *
* UK +44(1454)207-000 [email protected] *
* FRANCE +33(0)1 64551084 [email protected] *
* GERMANY +49/931/40468-71 [email protected] *
* NORWAY +47 67 57 21 30 [email protected] *
* SINGAPORE +65 6225-6015/16 [email protected] *
* INDIA +91(033)2357-3575 [email protected] *
* JAPAN +81(03)5952-6500 [email protected] *
* CHINA +86(411)363-1983 [email protected] *
* *
* North America [email protected] *
* Europe [email protected] *
* Asia [email protected] *
************************************************************
 Tutorial 3 3-109

3.11 Post-Processing

If there are no errors in the input, the analysis is successfully

completed. The extensive facilities of the Post-processing mode
can then be used to

a) view the results graphically and numerically

b) assess the suitability of the structure from the standpoint of
safety, serviceability and efficiency
c) create customized reports and plots

The procedure for entering the post processing mode is explained

in section 2.11.1 of this manual.

Node results such as displacements and support reactions are

available for all models. The methods explained in the first two
tutorials – see sections 2.11.2 to 2.11.7 – may be used to explore
these. If beams are present in the model, beam results will be
available too (see sections 2.11.8 to 2.11.18 for information on
these). For this example, we will look at the support reactions. We
do not have any beams in our model, so no results will be available
for this type of entity.

For plates, the results available are stresses, and “unit width” moments.
There are several different methods for viewing these results, as
explained in the next few sections.
3-110 Tutorial 3

3.11.1 Viewing stress values in a tabular form

From the View menu, select Tables (or click the right mouse
button in the drawing area and select Tables). Choose Plate Centre Stress.

Figure 3. 114 Figure 3. 115

 Tutorial 3 3-111
The following table will be displayed.

Figure 3. 116

The table has the following tabs:

Shear, Membrane and Bending: These terms are explained in

Section 1.6.1 of the STAAD Technical Reference Manual. The
individual values for each plate for each selected load case are
displayed.

Summary: This tab contains the maximum for each of the 8 values listed
in the Shear, Membrane and Bending tab.

Principal and Von Mises: These terms too are explained in

Section 1.6.1 of the STAAD Technical Reference Manual. The
individual values for each plate for each selected load case are
displayed, for the top and bottom surfaces of the elements.

Summary: This tab contains the maximum for each of the 8 values listed
in the Principal and Von Mises tab.

Global Moments: This tab provides the moments about the global
X, Y and Z axes at the center of each element.
3-112 Tutorial 3

3.11.2 Printing the tables

All of these tables may be printed by clicking the right mouse button
in the table area and selecting the Print option.

Figure 3. 117
 Tutorial 3 3-113

3.11.3 Changing the units of values which

appear in the above tables

The length and force units of the stresses and moments are
displayed alongside the individual column headings for the terms.
To view the values in a different set of units, go to the Tools menu
and select Set Current Display Unit.

Figure 3. 118
3-114 Tutorial 3

In the dialog box that comes up, click on the Force Units tab and
specify the required unit from the Stress and Moment fields. Click
on the Apply button for the changes to take effect immediately.
Once you are sure that you have chosen the proper unit
combination, click on the OK button.

Figure 3. 119
 Tutorial 3 3-115

3.11.4 Limiting the load cases for which the

results are displayed

When we entered the post-processing mode, we chose all load cases

in the Results Setup dialog box. The tables hence contain results for
all the load cases. To change that load list, choose Select Load Case
from the Results menu.

Figure 3. 120
3-116 Tutorial 3

In the dialog box that comes up, select the load cases you want,

and click on the single arrow , so they are transferred from the
Available category to the Selected category. Then, click on the OK
button.

Figure 3. 121
 Tutorial 3 3-117

3.11.5 Stress Contours

Stress contours are a color-based plot of the variation of stress or

moment across the surface of the slab or a selected portion of it. There
are 2 ways to switch on stress contour plots:

a) From the left side, select the Contour sub-page under the
Plate page.

Figure 3. 122

or
3-118 Tutorial 3

b) From the top of the screen, click on the Results menu and
select the Plate Stress Contour option.

Figure 3. 123
 Tutorial 3 3-119
In each of the above cases, the following dialog box appears.

Figure 3. 124

 From the Stress type field, select the specific type of stress
for which you want the contour drawn.
 From the Load Case selection box, select the load case
number.
 Stress values are known exactly only at the plate centroid
locations. Everywhere else, they are calculated by linear
interpolation between the center point stress values of
adjacent plates. The Enhanced type contour chooses a
larger number of points compared to the Normal type
contour in determining the stress variation.
 View Stress Index will display a small table consisting of
the numerical range of values from smallest to largest
which are represented in the plot.
3-120 Tutorial 3

Let us set the following:

 Load case – 102

 Stress Type – Von Mis Top
 Contour Type – Normal Fill
 Index based on Center Stress
 View Stress Index
 Re-Index for new view

Figure 3. 125

Click on the Apply button.

 Tutorial 3 3-121
The following diagram will be displayed. We can keep changing the
settings and click on Apply to see all the various possible
results in the above facility.

Figure 3. 126

Let us keep the dialog box open to examine the feature (Animation)
explained in the next section.
3-122 Tutorial 3

If some portion of the structure appears truncated, we can bring that

portion into view by choosing one of the following methods:

a. Click on the Zoom Out button to shrink the size of the

region drawn.
Before After

Figure 3. 127 Figure 3. 128

b. Use the Pan button to physically shift the position of

the structure away from the index.

Before After

Figure 3. 129 Figure 3. 130

 Tutorial 3 3-123

3.11.6 Animating stress contours

The same dialog box shown in the previous section may be used to obtain
the stress contours in an animated view. This is a method of getting a
“dynamic” instead of static representation of the plot.
After making the choices as explained in that section, click on the
Animation tab of that dialog box. Switch on Stress followed by
Apply.

Figure 3. 131

To stop the animation, click on No Animation and click Apply

again.
3-124 Tutorial 3

3.11.7 Creating AVI Files

AVI files are a mechanism by which a dynamic result, such as, a

deflection diagram in animation, may be captured and recorded.
Presently, this facility is available in STAAD for node deflection,
beam section displacement, mode shape and plate stress contour
diagrams.

The facility in STAAD for creating AVI files is under the Tools
menu and is called Create AVI File. These files can then be
viewed using tools such as the Windows Media Explorer.

Figure 3. 132
 Tutorial 3 3-125
The following dialog box will appear.

Figure 3. 133

In an animated view, the movement from one extremity to the other

is captured as several frames. The number of frames that comprise
such a movement is controlled by specifying a value for Total No.
of Frames. The speed of motion is controlled by the Frame Rate
/sec. The rest of the options in the above dialog box are for the
type of diagram from which the AVI file is to be created. Certain items
such as Mode Shape and Plate Stress contour do not become active
(remain grayed out) if the required data of that type are not present in the
STAAD file, such as a modal extraction, or finite
elements.
3-126 Tutorial 3

After making the appropriate selections, click OK. Following this,

another dialog box appears, where we are instructed to specify a
file name for the .AVI file. Subsequently, we are prompted for the
type of video compression. AVI files can be quite large, and
compression is a technique by which one may reduce the size of these
files.

Figure 3. 134

Finally, a message indicating that the operation was successful will appear
at the end of the file creation process as shown below.

Figure 3. 135

As mentioned earlier, other tools like Windows Media Explorer

may be used to view the AVI file. The file with the extension .AVI
should be located in the same folder where the STAAD input file is
present.
 Tutorial 3 3-127

3.11.8 Viewing plate results using element

query

Element Query is a facility where several results for a specific

element can be viewed at the same time from a single dialog box.
Let us explore this facility for element 4. Select element 4 and
double click on it. Alternatively, select element 4, and from the
Tools menu, choose Query – Plate.

Figure 3. 136

The various tabs of the query box enable one to view various types
of information such as the plate geometry, property constants,
stresses, etc., for various load cases, as well as print those values.
3-128 Tutorial 3

Some typical screens are shown.

Figure 3. 137

Figure 3. 138
 Tutorial 3 3-129

Figure 3. 139

Figure 3. 140
3-130 Tutorial 3

Figure 3. 141

The length and force units in which the values appear in the above tables
can also be modified using the method explained in section 3.11.3.
 Tutorial 3 3-131

3.11.9 Producing an onscreen report

Occasionally, we will come across a need to obtain results

conforming to certain restrictions, such as, say, the resultant node
displacements for a few selected nodes, for a few selected load
cases, sorted in the order from low to high, with the values
reported in a tabular form. The facility which enables us to obtain such
customized on-screen results is the Report menu on top of the screen.

Let us produce a report consisting of the plate principal stresses,

for all plates, sorted in the order from Low to High of the Principal
Maximum Stress (SMAX) for load cases 101 and 102.

The first step to do this is to select all the plates using the Plates

Cursor . Then, go to the Report | Plate Results | Principal

Stresses menu option as shown below.

Figure 3. 142
3-132 Tutorial 3

In the dialog box that appears, select the Loading tab. Make sure that
load cases 101 and 102 are selected as shown below.

Figure 3. 143
 Tutorial 3 3-133
Next, select the Sorting tab. Choose SMAX under the Sort by
Plate Stress category and set the Sorting Order List from Low to
High. (If we wish to save this report for future use, we may select
the Report tab, provide a title for the report, and turn on the Save
ID option.) Then, click on the OK button.

Figure 3. 144
3-134 Tutorial 3

The following figure shows the table of maximum principal stress with
SMAX values sorted from Low to High.

Figure 3. 145
 Tutorial 3 3-135
To print this table, click the right mouse button anywhere within the
table. A list of options will appear.

Figure 3. 146

Select the print option to get a hardcopy of the report.

To transfer the contents of this table to a Microsoft Excel file,

click at the top left corner of the table with the left mouse button.
The entire table will become highlighted. Click the right mouse button
and select Copy. Then, open an Excel worksheet, click at the desired
cell and click Paste.
3-136 Tutorial 3

3.11.10 Viewing Support Reactions

Since supports are located at nodes of the structure, results of this

type are available along with other node results like displacements.
To view the reactions graphically, click on the Node page on the left
side of the screen, and select the Reactions sub-page.

Figure 3. 147
 Tutorial 3 3-137
The reactions at the supports will be displayed on the drawing as shown
below.

Figure 3. 148

The six values – namely, the 3 forces along global X, Y and Z, and
the 3 moments Mx, My and Mz, in the global axis system are
displayed in a box for each support node. The words N1, N2, etc. stand
for the node numbers of the supports.
3-138 Tutorial 3

We may choose to “un-display” one or more of the 6 terms of each

support node in the following manner.

From the Results menu, choose View Value.

Figure 3. 149
 Tutorial 3 3-139
In the dialog box that comes up, click on the Reactions tab. Let us
switch off Global X and Global Z under the Direct category.
Then, click on the Annotate button followed by the Close button.

Figure 3. 150
3-140 Tutorial 3

The drawing will now contain only the remaining 4 terms (see figure
below).

Figure 3. 151

To change the load case for which the reactions are displayed, select
the desired case from the load selection box.

Figure 3. 152
 Tutorial 3 3-141
For better clarity in viewing the results in the drawing area (and for
reducing the clutter on the screen), a variety of methods are
available. For example, keep the mouse pressed on top of Zoom In
button, and watch the drawing get progressively bigger. Use the
Pan button to physically shift the drawing around. Other options
like Dynamic Zoom and Zoom Window buttons may also be used.
To restore the original view, click on the Display Whole Structure button.
(Some of these options are explained in greater detail in the ‘Frequently
Performed Tasks’ section at the end of this manual.)

Icon Name

Zoom In

Pan

Dynamic Zoom

Zoom Window

Display Whole
Structure
3-142 Tutorial 3

The table on the right side of the screen contains the reaction values
for all supports for all selected load cases.

Figure 3. 153

This table can also be displayed from any mode by clicking on the
View menu, choosing Tables, and switching on Support Reactions.
 Tutorial 3 3-143
The method explained in section 3.11.3 may be used to change the units
in which these values are displayed. The summary tab
contains the maximum value for each of the 6 degrees of freedom along
with the load case number responsible for it.

Figure 3. 154

This brings us to the conclusion of this tutorial. Additional help on using

plates is available in Examples 9, 10 and 18 in the Examples Manual.
3-144 Tutorial 3
 4-1

Tutorial Problem 4: Interoperability

(using STAAD.Pro and STAAD.etc)

Section 4
This tutorial is relevant only for users who have
purchased the program called STAAD.etc. Since this
tutorial is created using the Demo CD, the user will not
have the ability to alter certain input items.

This chapter provides a step-by-step tutorial on using the

interoperability features between STAAD.Pro and the program
called STAAD.etc. The structure created in Tutorial Problem 1 will be
used as the basis for this tutorial. This tutorial covers the
following topics:

 Understanding STAAD.etc
 Description of the tutorial problem
 Using the Interactive Mode in STAAD.Pro
 Designing a footing based on results from STAAD.Pro
 Designing a base plate based on results from STAAD.Pro
 Saving the Interactive Design information as a STAAD.etc file
4-2 Tutorial 4

4.1 Understanding STAAD.etc

STAAD.etc is the “engineer’s structural toolkit” containing various
component analysis and design module groups including
foundations, masonry, timber, steel, concrete and general analysis.
As a standalone product, STAAD.etc can be used to design small
portal frames, continuous beams, footings, retaining walls one-way
slabs, connections, shear walls and much more. STAAD.etc allows
the engineer to complete the design cycle on the primary structure
by analyzing and designing several structural components or
accessories within the STAAD.Pro environment using
STAAD.Pro’s results database.
 Tutorial 4 4-3

4.2 Description of the tutorial problem

Using the structure created in Tutorial Problem 1 as the primary model,
STAAD.etc will be utilized to analyze and design a footing and a base
plate inside the STAAD.Pro environment for the model.
4-4 Tutorial 4

4.3 Using the Interactive Mode in STAAD.Pro

Start the STAAD.Pro 2006 Program from your STAAD.Pro
program folder, as explained in Section 1.2. From File | Open, open
the file “Tut_01_portal.std” from the
../SPRO2006/STAAD/Examp/US directory as shown below (please
note that the .. represents the drive or root directory the program
was installed in) or from wherever the file was saved:

Figure 4. 1

The picture in the preview pane is made possible by a file with the
extension .emf. When a model is created using the graphical
method, or when a model is saved from the graphical mode, the
.emf file is created alongside the .std file. If you follow the
procedure explained in Section 1.5 of this manual for creating
tutorial 1, the Tut-01-portal.emf file will be produced, and if you
re-open the Tut-01-portal.std subsequently, you will see the picture
in the preview pane.
 Tutorial 4 4-5
If you have not performed the analysis and design for
“Tut_01_portal.std”, please execute the following steps:

1. After opening the file in STAAD.Pro, go to Analyze | Run

Analysis from the top menu bar as shown below.

Figure 4. 2

2. A dialog box providing a choice of engines to run the file with will
then popup. Select the STAAD Analysis engine as the default
engine and click on the Run Analysis button.

Figure 4. 3

3. If the analysis is successfully completed, a dialog box showing the

different steps STAAD took to analyze the structure will come up.
Click Done to proceed to the next step. If a message reporting
errors in the input file were found, please refer to Tutorial 1 to
rectify those problems.
4-6 Tutorial 4

Figure 4. 4

Starting the Interactive Mode in STAAD.Pro

After “tut_01_portal.std” has been successfully analyzed and

designed, click on Mode | Interactive Designs | Component
Design from the top menu bar as shown in the next figure. If this menu
item is “grayed-out”, the STAAD.etc program has not been installed
properly or is missing. Please install or reinstall the
STAAD.etc program from the STAAD.suite CD.
 Tutorial 4 4-7

Figure 4. 5

The STAAD.etc interface to STAAD.Pro is shown in the bottom right-

hand corner of the screen. At the time of release of
STAAD.Pro 2003 Build 1001, there are only three STAAD.etc
modules interfaced with STAAD.Pro 2003. These modules are the
footing, slab and base plate analysis/design as shown below.

Figure 4. 6
4-8 Tutorial 4

Using the Drag and Drop Facilities

To run any of the STAAD.etc modules, hold the left-mouse button down
over a particular module and drag it to a specific joint or
node in the main structure window.

Figure 4. 7
 Tutorial 4 4-9

4.4 Designing a Footing based on results from

STAAD.Pro
In this section of the tutorial, a footing will be designed for node
#1. The details of the input of the footing will not be discussed
here. For further information about the input for the STAAD.etc
footing module, please refer to the STAAD.etc HTML Help
accompanied with the STAAD.etc program.

To identify Node #1, click on Select | By List | Nodes… from the

main menu bar. Select number 1 in the list box.

Figure 4. 8 Figure 4. 9
4-10 Tutorial 4
Node #1 is now marked by a red dot in the main structure window
as shown below.

Figure 4. 10

Once Node #1 is identified, drag the footing icon from the

Interactive Design dialog box and drop it over #1. The input for
the footing pops up. Provide the name of the footing in the Job
Name edit box.
 Tutorial 4 4-11

Figure 4. 11

If the Column Depth and Width are not provided under the Column
Data box, obtain those data (either from the member query or from
the property table) and provide them. STAAD.etc defines the
Column Depth as the dimension of the supported column along the
local Y axis of the column. The Column Width is defined as the
dimension of the supported column along the local Z axis of the
column.
4-12 Tutorial 4

Leave the Concrete Pedestal option unchecked. Switch to the

Loading tab and select the Dead Load as Load Case 1 (the
Selfweight load case) and the Live Load and Wind Load as None. Check
the Reversal of Wind option off as shown below.

Figure 4. 12

Keep all the other data as the defaults. Click on OK to begin

designing the footing for Node #1. If the design completes
successfully, the results for the footing will be displayed in a
separate window. Each interactive design module produces a
separate results window containing three tabs at the bottom. These tabs are
Results, Calculations and Output Drawing.
 Tutorial 4 4-13
The different facets of the results output are as follows:

Tab Description Sample

Displays all results (analysis

Results
and design) in tabulated
form

Displays the step-by-step

intermediate calculations
Calculations
explaining the derivation of
all results.

Output Detailed output drawing

Drawing schematic

Figure 4. 13
4-14 Tutorial 4
Editing and Viewing Interactive Designs

All interactive design results for a particular STAAD file are listed
in the Interactive Design dialog box which can be brought up by
clicking on Mode | Interactive Design from the top menu bar. To
view any interactive design result, select the design job and click
on View Results. To edit any job, select the job and click on Edit
Job to bring up the input dialog box with the existing data.

Figure 4. 14

STAAD.Pro also has the ability to design group footings. This

tutorial does not cover the basics of running a group footing inside
of STAAD.Pro.
 Tutorial 4 4-15

4.5 Designing a base plate based on results from

STAAD.Pro
The base plate and other modules in the Interactive Design mode of
STAAD.Pro are similar to the footing module explained
previously. A brief description of the base plate input will be
explained here. For a detailed description of the base plate module,
please refer to the STAAD.etc HTML Help.

Following the steps in the footing module tutorial in Section 4.4,

the input for a base plate can be supplied after the base plate icon
is dragged and dropped over a particular support joint. A base plate
can be designed only for a member with a support.

Figure 4. 15

To check the adequacy of an existing base plate for a specfic load case,
provide the Plate Length, Plate Width and Thickness of that plate.
However, to have the program design a base plate, set the
Plate Length, Plate Width and Thickness to zero (0).
4-16 Tutorial 4

4.6 Saving the interactive design as a STAAD.etc

file
All interactive design jobs are saved with the STAAD.Pro “.std”
input file as a separate file with the extension “.etc”. For example,
in this tutorial, the STAAD file is named tut_01_portal.std .
Thus, the name of the interactive design file will be
tut_01_portal.etc and will be saved in the same directory as the
“tut_01_portal.std” file.

STAAD.Pro is capable of inherently reading STAAD.etc files

without the need for importing or exporting the file. Similarly, any “.etc”
file generated by STAAD.Pro can be read in STAAD.etc.
This is particularly useful when the engineer wants to design other
structural components on top of the ones already produced in
STAAD.Pro.
4-17
4-18
Frequently Performed Tasks
 FPT-1

1. Selecting nodes, beams, plates, etc.

The Selection Toolbar

FPT-2 Frequently Performed Tasks

Icon Corresponding Menu/Sub-menu Purpose Description

options

Select | Nodes Cursor

Used to select First, select the Nodes
nodes Cursor. Then, click on
graphically the nodes you wish to
select. To select
multiple nodes, hold
Nodes down the Control key
Cursor while selecting, or
create a rubber-band
style window around
the desired nodes.

Select | Beams Cursor Used to select First, select the Beams

beams Cursor. Then, click on the
graphically members you wish to
select. To select
multiple members, hold
Beams down the Control key
Cursor while selecting, or
create a rubber-band
style window around
the desired beams.
 Frequently Performed Tasks FPT-3

Icon Corresponding Menu/Sub-menu Purpose Description

options

Select | Plates Cursor Used to select First, select the Plates

plates Cursor. Then, click on
graphically the plates you wish to
select. To select
multiple plates, hold
Plates down the Control key
Cursor while selecting, or
create a rubber-band
style window around
the desired plates.

Select | Surface Cursor Used to select First, select the

surface Surface Cursor. Then,
graphically click on the surface you
wish to select. To select
multiple
Surface surfaces, hold down
Cursor the Control key while
selecting, or create a
rubber-band style
window around the
desired surfaces.
FPT-4 Frequently Performed Tasks

Icon Corresponding Menu/Sub-menu Purpose Description

options

Select | Solids Cursor Used to select First, select the Solids

solids Cursor. Then, click on
graphically the solids you wish to
select. To select
multiple solids, hold
Solids down the Control key
Cursor while selecting, or
create a rubber-band
style window around
the desired solids.

Select | Geometry Cursor Used to select First, select the

any geometry Geometry Cursor.
graphically. It is Then, click on the
a mechanism for entity you wish to
selecting nodes, select. To select
Geometry beams, plates multiple entities, hold
Cursor and solids, or, down the Control key
any combination while selecting, or
of these, create a rubber-band
simultaneously. style window around
the desired entities.
 Frequently Performed Tasks FPT-5

Icon Corresponding Menu/Sub-menu Purpose Description

options

Select | Load Edit Cursor

Used to First, select the Load
graphically Edit Cursor. Then,
select a double-click on the
component of an diagram of the load
existing load component you wish to
Load Edit case for edit.
Cursor modification.

Select | Support Edit Cursor

Used to First select the Support
graphically Edit Cursor. Then,
select a support double-click on the
whose support icon at the
parameters one node where you wish
Support Edit may wish to to modify the details of
Cursor modify. the existing support.
FPT-6 Frequently Performed Tasks

Icon Corresponding Menu/Sub-menu Purpose Description

options

Select | Release Edit Cursor

Used to First, select the
graphically Release Edit Cursor.
select and Then, double-click on
modify an the member on which a
existing member currently defined
release START or END release
Release Edit
specification condition has to be
Cursor
modified.

Select | Text Cursor

Used to enter To edit any pre-created
the mode for text, first, select the
editing pre- Text Label Cursor.
created text Then, double-click on
labels the text that you wish to
modify.
Select Text
 Frequently Performed Tasks FPT-7

Icon Corresponding Menu/Sub-menu Purpose Description

options

Enables the user Please refer to

to select STAAD.Pro 2004 2nd
multiple types of Edition Release
geometric Report.
Filtered entities (nodes,
Selection beams,
surfaces, etc.)
with specific
attributes in one
pass.
FPT-8 Frequently Performed Tasks

2. Viewing the structure from different angles

The Rotation Toolbar

 Frequently Performed Tasks FPT-9

Icon Description Example

Displays the structure as seen

from the front. When the
global Y axis is vertical, this is
the elevation view, as looking
towards the negative direction
View From of the Z-axis.
+Z

Displays the structure as seen

from the back. When the
global Y axis is vertical, this is
the elevation view, as seen
looking towards the positive
direction of the Z-axis.
View From -
Z

Displays the structure as seen

from the right side. When the
global Y axis is vertical, this is
the side elevation, as seen
looking towards the negative
View From direction of the X-axis.
+X
FPT-10 Frequently Performed Tasks

Icon Description Example

Displays the structure as seen

from the left side. When the
global Y axis is vertical, this is
the side elevation, as seen
looking towards the positive
direction of the X-axis.
View From -
X

Displays the structure as seen

from the top looking down.
When the global Y axis is
vertical, this is the plan view,
as seen from the sky looking
View From down.
+Y

Displays the structure as if one

is looking up skywards.

View From -
Y
 Frequently Performed Tasks FPT-11

Icon Description Example

Displays the structure in the

isometric view. The angle
which defines isometric view is
generally X = 30, Y = 30, Z = 0

Isometric
View
FPT-12 Frequently Performed Tasks

3. Switching on labels for nodes, beams, plates, etc.

Labels are a way of identifying the entities we have drawn on the

screen. To demonstrate this facility, let us open EXAMP01.std.
The structure will look as shown below.
 Frequently Performed Tasks FPT-13

1. To switch the node and beam labels on, we may utilize any one of
the following methods:

a. Click on the Symbols and Labels icon as shown below.

b. Click the right mouse button anywhere in the drawing area. In

the dialog box that appears, choose Labels (as shown in the
figure below).
FPT-14 Frequently Performed Tasks

c. Select the View menu followed by the Structure Diagrams

option from the top menu bar, and the Labels tab of the dialog box
that comes up.
 Frequently Performed Tasks FPT-15

2. In all of the above three cases, the following Diagrams dialog box
will appear. Make sure that the Labels tab is selected. Then,
switch the appropriate labels on and click on OK.
FPT-16 Frequently Performed Tasks

The following figure shows the structure with the node and beam labels
displayed on it.
 Frequently Performed Tasks FPT-17

3. To change the font of the node/beam labels, go to the View menu

and select the Options command. Then, select the appropriate tab
(Node Labels / Beam labels) from the Options dialog box. Choose
the Font option and make the necessary changes.
FPT-18 Frequently Performed Tasks

4. Displaying a portion of the model by isolating it from

the rest of the structure

Sometimes, the large number of entities that are drawn on the screen
may make it difficult to clearly see the details at any
particular region of the structure. In such cases, one is confronted with
the task of de-cluttering the screen or looking at specific
regions or entities while removing the rest of the structure from the
view.

There are different methods in STAAD.Pro by which the user can view a
portion of the structure. The following pages demonstrate three different
methods.

Method 1 – View | New View

Steps:

1. To demonstrate this method, let us open EXAMP08.STD file. The

structure will look as shown below.
 Frequently Performed Tasks FPT-19

2. Let us say that we wish to view only the members which are at the
midheight level. The first step to doing this is to select those
members. The quickest way to select them is to bring up the View

From + Z and creating a rubber-band around them, after

making sure that the Beams Cursor is the active cursor.

3. To visually verify that the correct members have been selected,

click on the Isometric View icon . The selected members will

appear in one color and the rest of the structure in another.
FPT-20 Frequently Performed Tasks

4. Next, either click the right mouse button and select the New View
option or, pull down the View menu and select the New View
option.

5. In either case, the following dialog box comes up. These radio
buttons determine whether the selected view would be opened in a new
(‘child’) window or whether it would replace the current
(‘parent’) view window. Let us select the Create a new window for
the view option and click on the OK button.
 Frequently Performed Tasks FPT-21

The portion of the structure that we selected will now be displayed

in a new window as shown below. We can create more than one
‘child’ view window this way.

All sorts of operations can be performed inside the ‘New View’

such as adding and deleting members, assigning properties, loads,
supports, etc. A new view of a selected portion offers the
advantage of de-cluttering the screen and limiting the displayed objects
to just a few chosen entities.

6. To return to the ‘parent’ view window, simply close the new view
(‘child’) window.
FPT-22 Frequently Performed Tasks

7. Next, let us try the Display the view in the active window option.
Follow steps 2 to 4. Then, select the Display the view in the active
window option and click on the OK button.

The original structure will be hidden and, the portion of the

structure that we selected will instead be displayed in the current
(‘parent’) window as shown below.
 Frequently Performed Tasks FPT-23

We may restore the original view of the structure by simply

clicking on the Display Whole Structure icon.

These new views may be saved by going to the View | View

Management | Save View menu option. Provide a title for the new view.
These saved views may later be opened by going to the View
| Open View menu option.

Method 2 – Tools | Cut Section

Steps:

1. To demonstrate this method, let us once again open

EXAMP08.STD file. The structure will look as shown below.
FPT-24 Frequently Performed Tasks

We will once again try to view just the members at the mid-height level.

2. Click on the Symbols and Labels icon and in the Diagrams dialog
box that comes up, switch the Node Numbers on. The reason for
doing this will become evident in the next step.
 Frequently Performed Tasks FPT-25

3. From the Tools menu, select Cut Section.

FPT-26 Frequently Performed Tasks

The following dialog box comes up.

The Range By Joint method

Since the beams of the mid-height level happen to contain joint #

10 (or any of the joint numbers from 7 to 12), it would be
convenient if we could instruct the program to display the entities
lying in the X-Z plane, and passing through any one of those joints
7 to 12. The facilities of the Range By Joint tab enable us to do
that.

4. Let us select that tab (it happens to be the default). Here, we can
select the plane of the section by clicking on one of the options –
X-Y, Y-Z, or X-Z. We have to choose the X-Z plane for our
example. Then, in the Node # drop down list, provide a joint that
lies on the sectional plane. In our example, we may choose any one
of the nodes between 7 and 12. Let us choose node # 10. Click on
the OK button.
 Frequently Performed Tasks FPT-27

The following figure shows the cut portion of the original structure
displayed in the drawing area.

5. To restore the original view, simply click on the Display Whole

Structure icon.

Alternatively, go to the dialog box shown in step 4 and click on the

Show All button.
FPT-28 Frequently Performed Tasks

The Range By Min/Max method

Steps:

Another convenient way of choosing the beams at the mid-height

level is to specify that those beams lie in the X-Z plane between
the Y range values of 12ft - a and 12ft + a, where, “a” is an
arbitrary value such as say, 2ft.

6. To do this, let us select the Range By Min/Max tab. Here, we can

again select the plane of the section by clicking on one of the
options – X-Y, Y-Z, or X-Z. We have to choose the X-Z plane for
our example. The Minimum and Maximum edit boxes represent the
boundary distances along the axis perpendicular to the sectional
plane. Every object lying between these two distances will be
displayed. In our example, let us provide 10 as the Minimum and
14 as the Maximum distance. (Before doing so, make sure that the
current input units of length, displayed at the bottom right corner
of the STAAD program window, are feet.) Then, click on the OK
button.
 Frequently Performed Tasks FPT-29

The following figure shows the cut portion of the original structure
displayed in the drawing area.

7. To restore the original view, again, click on the Display Whole

Structure icon or click on the Show All button in the dialog box
shown in step 6.
FPT-30 Frequently Performed Tasks

The Select to View method

For demonstrating this method, instead of viewing specific beams, let us

look at the nodes instead.

Steps:

Using this option, the portion of the structure we wish to view can
be selected by specifying the objects which lie in that portion. The
Window/Rubber Band option allows us to select the portion of the
structure to view by specifying a rubber-band window around it.
The View Highlighted Only option displays only the selected
(highlighted) objects on screen and, the members and elements we wish to
view must be selected before choosing this option. The
Select To View option allows us to view only Beams, Plates, and/or
Solids, depending on the corresponding check boxes that are
activated.

8. For our example, let us choose the Select To View option and
check the Nodes check box. Then, click on the OK button as
shown below.
 Frequently Performed Tasks FPT-31

The following figure shows the view of the structure with only the
nodes displayed.

9. To restore the original view, click on the Display Whole

Structure icon or click on the Show All button in the dialog box shown
in step 8.

These new views may be saved by going to the View | View

Management | Save View menu option. Provide a title for the new view.
These saved views may later be opened by going to the View
| Open View menu option.
FPT-32 Frequently Performed Tasks

Method 3 – View | Zoom

The Zoom menu option allows us to zoom in (magnify) or out

(reduce) on a portion of the structure, as one would, using a
telescope.

Steps:

1. To demonstrate this method, let us open EXAMP09.STD file. The

structure will look as shown below.
 Frequently Performed Tasks FPT-33

2. Say, we want to magnify the portion of the structure shown in the

figure below.

3. To select the plates as shown in the above figure, click on the

View From + Z icon. Then, using the Plates Cursor , select
the plates by rubber-banding around them as shown below.

By the way, looking at the model from View From + Y, or, View
From - X, and using the rubber-band window methods can be just
as effective in selecting these elements.
FPT-34 Frequently Performed Tasks

4. To restore the original isometric view, click on the Isometric

View icon. We do this only to make sure that we have selected the correct
entities.

5. To magnify the selected portion of the structure, either click on the

Zoom Window icon or, pull down the View menu and select the
Zoom | Zoom Window menu option as shown below.
 Frequently Performed Tasks FPT-35

The cursor changes as shown below.

6. Using the cursor, drag a window around the selected portion of the
structure.

The magnified view of the selected portion of the structure will now be
displayed in the drawing area as shown below.
FPT-36 Frequently Performed Tasks

If we click on the Zoom In icon, it magnifies or enlarges the view

of the structure even further by a pre-defined factor. You can keep
the mouse cursor pressed over the Zoom In or Zoom Out icons,
and the screen will continuously refresh to draw the structure larger
or smaller.

To display the enlarged view in a new window, use the Dynamic Zoom
icon instead of the Zoom Window option.

The region you wish to see will have to be selected by creating a

rubber-band window around it. That region will now be displayed
in a new window in the drawing area as shown in the next figure.
 Frequently Performed Tasks FPT-37

7. To restore the view of the full structure, click on the Display

Whole Structure icon.

These new views may be saved by going to the View | View

Management | Save View menu option. Provide a title for the new view.
These saved views may later be opened by going to the View
| Open View menu option.
FPT-38 Frequently Performed Tasks

5. Creating Groups

Group names are a means for easily identifying a collection of entities

like Beams, Plates or Solids using a single moniker. By grouping these
entities, we need to assign attributes such as member properties and
material constants just to the group, a
simple process, compared to the task of assigning them to the
individual members.

Steps:

1. To demonstrate this, let us open EXAMP01.STD file. The structure

will look as shown below.
 Frequently Performed Tasks FPT-39

Let us classify the members of the topmost level of this structure into
three groups – Top Chords, Bottom Chords and Transverse Truss.

Top Chords:

2. Make sure that the Beams Cursor has been selected. Then,
using the mouse, select the inclined members as shown in the
figure below.
FPT-40 Frequently Performed Tasks

3. From the Tools menu, choose Create New Group.

 Frequently Performed Tasks FPT-41

4. In the Give Group Name dialog box, type _TOPCOR for Group
name (Group Names must begin with the underscore ‘_’ character). Since
group names can be assigned to Nodes, Beams, Plates,
Solids as well as a general category called Geometry, it is very
important that we choose the proper entity type. Hence, specify the
Select Type as Beam.

5. Click on the OK button. Notice that the Assign Methods in the

Create Group dialog box is presently set to Associate to Selected
Geometry. Click on the Associate button.

Click anywhere in the drawing area to un-highlight the highlighted

members. This is necessary before we start selecting the members
for the next group name.
FPT-42 Frequently Performed Tasks

Bottom Chords:

6. Using the mouse, select the bottom chords as shown in the figure
below.
 Frequently Performed Tasks FPT-43

7. Next, to bring up the Give Group Name dialog box, click on the
Create button. Then, follow steps 4 and 5 and assign the Group
Name _BOTCOR to these members.

Click anywhere in the drawing area to un-highlight the highlighted

members.
FPT-44 Frequently Performed Tasks

Transverse Truss:

8. Using the mouse, select the Transverse Truss members as shown in

the figure below.
 Frequently Performed Tasks FPT-45

9. Next, follow step 7 except for specifying the Group Name as

_TRNTRUS.

Click anywhere in the drawing area to un-highlight the highlighted

members. Also, Close the Create Group dialog box.

Three groups have now been created. If we now go to the Select menu, an
option called By Group Name should be available. Let us click on that
option, and the following dialog box comes up.
FPT-46 Frequently Performed Tasks

It is apparent that we can now select the members using the group name
method. If the check boxes for Show Label are switched off, labels such
as beam numbers will not be displayed for these
specific members, even if the beam numbering icon is switched on for the
entire structure.
 Frequently Performed Tasks FPT-47

6. Displaying Loads on the screen

Steps:

1. To demonstrate this feature, let us open EXAMP08.STD file. The

structure will look as shown below.
FPT-48 Frequently Performed Tasks

2. The easiest way to display a load is to click on the Loads icon as

shown below. To choose a specific load, we can click in the list
box called Active Load and choose the one we want.

Alternatively, we may pull the View menu down and select the
Structure Diagrams menu option. In the Diagrams dialog box that opens,
select the Loads and Results tab. Check the Loads check
box and select the load case we want from the Load Case list box. Then,
click on the Apply button.

Drag the dialog box out of the way if it obstructs the view of the
structure.
 Frequently Performed Tasks FPT-49

The following figure shows load case 1 displayed on our structure.

FPT-50 Frequently Performed Tasks

3. We can change the color in which load icons are drawn. Click on
the color button alongside the Loads checkbox, and make a new
choice from the color palette (see figure below).

Let us assign say, blue color, as shown in the above figure. Select
load case 2 from the Load Case list box.
 Frequently Performed Tasks FPT-51

The following figure shows load case 2 displayed (in blue) on our
structure.
FPT-52 Frequently Performed Tasks

7. Displaying Load Values on the screen

Steps:

1. In the previous exercise, we saw the method for turning on load

icons, but not the numeric value of those loads. To view load
values, let us open EXAMP01.STD file. The structure will look as shown
below.
 Frequently Performed Tasks FPT-53

2. Let us first display the load by clicking on the Loads icon .

After this, click the right mouse button and choose the Labels
option. Alternatively, we may click on the Symbols and Labels
icon or go to View | Structure Diagrams and select the Labels
tab in the Diagrams dialog box.
FPT-54 Frequently Performed Tasks

3. The dialog box shown below appears. Switch on the Load Values
option under the Loading Display Options category as shown
below.
 Frequently Performed Tasks FPT-55

The following figure shows our structure with the load values
displayed on it.
FPT-56 Frequently Performed Tasks

4. To change the unit in which load values are displayed, go to Tools

| Set Current Display Unit menu command.
 Frequently Performed Tasks FPT-57

In the Options dialog box that comes up, select the Force Units
tab. Then, change the selection under the Force, Distributed Force,
etc. options as shown below.

The following figure shows our structure with the load values
displayed in KN/m.
FPT-58 Frequently Performed Tasks

8. Structural Tool Tip Options

Structural tool tips offer a facility for displaying any customized input
or output information about a node, beam, plate or solid
element when the mouse cursor is placed over the structural entity.
The tool tips are similar to the ones displayed when the mouse cursor
hovers over a toolbar icon. When the mouse cursor is
moved away from that spot, the information displayed is switched off
too.

To activate the structural tool tips, go to View | Structural Tool Tip

Options from the top menu.
 Frequently Performed Tasks FPT-59

The dialog box shown in the figure below will prompt for the data
to be displayed when the mouse hovers a particular structural
entity.

To turn the structural tool tips on or off, check the Show Tool Tip
box in the upper left hand corner. The Tip Delay box signifies the
amount of time it takes from when the mouse cursor first appears
over an entity to when the tool tip actually pops up. This number is
expressed in milliseconds (i.e. 1000 = 1 second). The options
(items that can be displayed) for each entity are shown under the
Options box. A check mark signifies that the particular data item will be
displayed in the tool tip. An option with a “+” next to it signifies that
further options can be enabled or disabled.
FPT-60 Frequently Performed Tasks

The figure below shows the options that can be turned on or off for Node
Displacements.

A red “X” indicates the data will not be shown in the tool tip.
Simply click on the check box to turn an option on or off.
 Frequently Performed Tasks FPT-61

The resulting tool tip that is displayed from the options chosen in the
previous figure is shown in the figure below.

The tool tips automatically display the results for the active load case.
All values are reported in the current display units.
FPT-62 Frequently Performed Tasks

9. Identifying Beam Start and End

When assigning attributes like member releases or member offsets, one

additional item of information which accompanies this
information is whether that attribute is applied at the “START” node
of a member or the “END” node. Hence, there has to be a
way to quickly identify these two points without mistaking one for the
other.

Steps:

1. To demonstrate this, let us open EXAMP01.STD file. The structure

will look as shown below.
 Frequently Performed Tasks FPT-63

2. There are two different ways to identify the start and/or end of a
beam:

a) simply place the mouse over a specific beam. The

resulting tool tip will display the start node and end node
of that beam in two distinct colors along with their
corresponding coordinates. Of course, it is necessary to have
the tool tips display turned on for this method to work.
FPT-64 Frequently Performed Tasks

b) Click the right mouse button anywhere in the drawing

area and choose Labels.
 Frequently Performed Tasks FPT-65

The following Diagrams dialog box will appear. Make sure that
the Labels tab is selected. Then, switch the Beam Ends option on.
To alter the color in which the start and/or end is displayed, simply
click on the color palette next to the Start Color and/or End Color
options and choose the color you
want. Then, click on Apply for the changes to take effect
immediately. Click on OK to close the dialog box.
FPT-66 Frequently Performed Tasks

The following figure shows the structure with the start and end of all
beams displayed in two separate colors.
 Frequently Performed Tasks FPT-67

10. Plotting from STAAD.Pro

Explained below are 5 methods for plotting the drawing of the

STAAD model and STAAD result diagrams.

Method 1 : Using the Print Current View option

1. We shall use example problem 14 to illustrate this feature. Open

the example. The model should appear as shown below.
FPT-68 Frequently Performed Tasks

2. To plot this picture, click on the Print Current View icon as

shown in the following figure.

3. The standard Windows Print dialog box will appear asking you to
choose the printer to which you wish to plot the drawing.
 Frequently Performed Tasks FPT-69

4. If you wish to catch a glimpse of the plot, as it would appear on

paper, select the Print Preview Current View option.

A preview screen similar to the one shown below will be

displayed.
FPT-70 Frequently Performed Tasks

Method 2 : Using the Take Picture option

1. Bring up the diagram of the STAAD model you wish to print. On

the Print toolbar of the STAAD screen, you will find an icon of a
camera called Take Picture.

Alternatively, this option can be accessed from Edit | Take Picture.

2. A dialog box will appear prompting you to provide a Picture ID

and caption.
 Frequently Performed Tasks FPT-71

3. Next, select Report Setup from the File menu, or click on the
Report Setup icon as shown below.

4. A Report Setup dialog box will appear. In the Items tab, select
Pictures from the available list of items.
FPT-72 Frequently Performed Tasks

5. If more than one picture is available, select the one you wish to
plot by pressing the button. Next, go to the Picture Album
tab and switch on Full Page. Click OK.

6. From the File menu, select Print – Report. The diagram will be
plotted.

Alternatively, from the File menu, select Export Report | MS Word

File.
 Frequently Performed Tasks FPT-73

7. In the Save As dialog box, type in the name of the “.doc” file you
want and click on the Save button. In the template dialog box,
select the Normal template.

Microsoft Word will now start building the file with the picture in
it. Once this task is completed, Word will open this file, and
program can be accessed from the Windows Taskbar. Browse the file,
and if you are sure the image meets your needs, select Print from the
File menu and follow the instructions.
FPT-74 Frequently Performed Tasks

Method 3 : Using the Export View option

1. STAAD.Pro has a facility to export the drawing to a graphic image

file. The icon for this facility is called Export View and is
available in the Print toolbar.

2. When the diagram that you wish to plot is displayed on the screen,
click on the Export View icon. Select the graphic format in which
you wish to save the file (i.e., .bmp, .jpg, .tif, .gif, etc.)

Provide a file name and save the file.

 Frequently Performed Tasks FPT-75

3. Then go to a document publishing or graphic editing program such

as Microsoft Word or Adobe Photoshop. Import the drawing from
the file saved above. In Word, this can be done using Insert |
Picture | From File. Once you are sure the image meets your
needs, select Print from the File menu and follow the instructions.

Method 4 : Using the Copy Picture option

1. Highlight the window containing the diagram that you wish to plot.
This can be done by making sure the title bar of that window has the
color which indicates that it is in focus. From the Edit menu, choose
Copy Picture.

2. Next, run a graphics program which offers facilities for handling

graphic images such as Microsoft Paint, Adobe Photoshop, etc. In
the Edit menu of that program, select Paste. You will notice that
the drawing from the STAAD window is now pasted in that
program. Using the tools provided by the graphics program, you can
modify the drawing if you wish. Once you are sure the image meets your
needs, select Print from the File menu and follow the instructions.
FPT-76 Frequently Performed Tasks

Method 5 : Using the Windows Clipboard

1. When the diagram that you wish to plot is displayed on the screen,
press the "Print Screen" key on your keyboard or “Shift-Print
Screen", depending on how your keyboard is set up. The entire
image currently in view will be copied to the Windows clipboard. Next,
run a graphics program which offers facilities for cropping portions of a
graphic image (such as Microsoft Paint, Hijaak, Full Shot, etc.). In the
Edit menu of those programs, select Paste. You will notice that the entire
STAAD screen including the diagram, menus, toolbar icons, tables, etc.,
which were in view, are part of the pasted image. Using the tools
provided by the graphics
program, crop the image so as to preserve just the drawing and
eliminate unwanted portions. Using the File | Print option, print the
drawing.
Frequently Performed Tasks FPT-77
FPT-78 Frequently Performed Tasks