Scribd
Upload
71 views

ConversionofElectromechanicalsettingtoDigitalsetting r3

This document summarizes the differences between electromechanical and digital relay settings for time overcurrent and instantaneous overcurrent protection. For time overcurrent relays, the electromechanical settings are based on taps while digital relays use primary or secondary CT ratings. Instantaneous overcurrent relay settings also differ, with electromechanical relays using a dial setting and digital relays using CT ratings. The document provides examples of corresponding settings and explains key elements like curve shapes, pickup values, and reset types for both relay types.

Uploaded by

mohsobhy86
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
71 views

ConversionofElectromechanicalsettingtoDigitalsetting r3

This document summarizes the differences between electromechanical and digital relay settings for time overcurrent and instantaneous overcurrent protection. For time overcurrent relays, the electromechanical settings are based on taps while digital relays use primary or secondary CT ratings. Instantaneous overcurrent relay settings also differ, with electromechanical relays using a dial setting and digital relays using CT ratings. The document provides examples of corresponding settings and explains key elements like curve shapes, pickup values, and reset types for both relay types.

Uploaded by

mohsobhy86
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

Overcurrent Relaying

Conversion of Electromechanical (EM) setting to Digital setting


TOC = Time OverCurrent
IOC = Instantaneous OverCurrent

Electromechanical time overcurrent relays are set based on taps.


Digital time overcurrent relays are set based on 5A secondary or primary CT setting.

Electromechanical instantaneous overcurrent relays are set based on a dial setting (not time dial).
Digital instantaneous overcurrent relays are set based on 5A secondary or primary CT setting.

For example: Setting EM Digital (for 5A CTs)_____


TOC Pickup value Tap = 5 1 x CT or 1 x PU
Tap = 2 0.4 x CT or 0.4 x PU

IOC Pickup value 30A 6 x CT or 6 x PU


(dial setting)

Curve Shape Inverse (IAC51) IAC Inverse


Very Inv (IAC53) IAC Very Inv
Ext Inv (IAC77) IAC Ext Inv

Curve used Time Dial Multiplier


within family

Reset Timed Timed (linear) or Fast

Instantaneous Overcurrent (function 50)

 The instantaneous overcurrent protective element operates with no intentional time delay when the current has exceeded the
relay setting
 There is a pickup setting. Pickup usually set at 25% higher than the maximum current seen by the relay for a three-phase fault at
the end of the line.
 50P – phase inst. overcurrent - typical pickup setting of 6-10 x CT rating
 50N – neutral inst. overcurrent - typical pickup setting of of 6-10 x CT rating
(The phasor summation of phase currents Ia, Ib, Ic equals In)
 50G – ground inst. overcurrent - typical pickup setting of of 6-10 x CT rating
(The electrical summation of phase currents Ia, Ib, Ic equals Ig)

/conversion/tmp/scratch/416826339.doc
Time Overcurrent (function 51)

 Where it is desired to have more time delay before the element operates for the purpose of coordinating with other protective
relays or devices, the time overcurrent protective element is used.
 The trip time varies inversely with current.
 Characteristic curves most commonly used are called “inverse”, ”very inverse,” and “extremely inverse.” The user must select the
curve type. They are said to be a family of curves and selected by the time dial.
 There is a minimum pickup setting. The pickup setting should be chosen such that the protective device will be operating on the
most inverse part of its time curve over the range of current for which must operate.
 51P – phase time overcurrent – typical pickup setting of 1.0pu or 1 x CT rating
 51N – neutral time overcurrent – typical pickup setting of 0.3pu or 0.3 x CT rating
(The phasor summation of phase currents Ia, Ib, Ic equals In)
 51G – ground time overcurrent – typical pickup setting of 0.3pu or 0.3 x CT rating
(The electrical summation of phase currents Ia, Ib, Ic equals Ig)

During the selection of


the curve, the protection
engineer will uses what
is termed as a “ time
multiplier” or “time dial”
to effectively shift the
curve up or down on the
time axis

Reset of Time Overcurrent Element


There are (2) different types of resets within Time Overcurrent Protection:

 EM or Timed Delay Reset – this mimics the disc travel of an electromechanical relay moving back to the reset
position.
o If the disc has not yet completely traveled back to the reset position and the time overcurrent element
picks up again, the trip time will be shorter.
o If the current picks up and then dropouts many times, the disc will “ratchet” itself to the operate position.
o Be careful when coordinating with upstream or downstream devices.

 Instantaneous Reset – once the time overcurrent element operates, it will reset immediately

CGW 10-08-06

/conversion/tmp/scratch/416826339.doc

You might also like