TN-ED-04: GDDR6 Design Guide

Introduction

Technical Note
GDDR6: Design Guide

Introduction
GDDR6 is a high-speed synchronous dynamic random-access (SDRAM) memory de-
signed to support applications requiring high bandwidth such as graphic cards, game
consoles, and high-performance compute systems, as well as emerging applications
that demand even higher memory bandwidth.
In addition to standard graphics GDDR6, Micron offers two additional GDDR6 devices:
GDDR6 networking (GDDR6N) and GDDR6 automotive. GDDR6N is targeted at net-
working and enterprise-class applications. GDDR6 automotive is targeted for automo-
tive requirements and processes. All three Micron GDDR6 devices have been designed
and tested to meet the needs of their specific applications for bandwidth, reliability and
longevity.
This technical note is designed to help readers implement GDDR6 as an off-the-shelf
memory with established packaging, handling and testing. It outlines best practices for
signal and power integrity, as well as standard GDDR6 DRAM features, to help new sys-
tem designs achieve the high data rates offered by GDDR6.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 1 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are for evaluation and reference purposes only and are subject to change by
Micron without notice. Products are only warranted by Micron to meet Micron's production data sheet specifications. All
information discussed herein is provided on an "as is" basis, without warranties of any kind.
 TN-ED-04: GDDR6 Design Guide
GDDR6 Overview

GDDR6 Overview
In the DRAM evolutionary process, GDDR6 has made a significant leap in throughput
while maintaining standard packaging and assembly processes. While standard DRAM
speeds have continued to increase, development focus has been primarily on density —
often at the expense of bandwidth. GDDR has taken a different path, focusing on high
bandwidth. With DDR4 operating from 1.6 to 3.2 Gb/s, LPDDR4 up to 4.2 Gb/s, and
GDDR5N at 6 Gb/s, the increase in clock and data speeds has made it important to fol-
low good design practices. Now, with GDDR6 speeds reaching 14 Gb/s and beyond, it is
critical to have designs that are well planned, simulated and implemented.
GDDR6 DRAM is high-speed memory designed specifically for applications requiring
high bandwidth. In addition to graphics, Micron GDDR6 is offered in networking
(GDDR6N) and automotive grades, sharing similar targets for extended reliability and
longevity. For the networking and automotive grade devices, maximum data rate and
voltage supply differ slightly from Micron graphics GDDR6 to help assure long-term re-
liability; all other aspects between Micron GDDR6, GDDR6N and GDDR6 automotive
are the same. All content discussed in this technical note applies equally to all GDDR6
products. 12 Gb/s will be used for examples, although higher rates may be available.
GDDR6 has 32 data pins, designed to operate as two independent x16 channels. It can
also operate as a single x32 (pseudo-channel) interface. Internally, the device is config-
ured as a 16-bank DRAM and uses a 16n-prefetch architecture to achieve high-speed
operation. The 16n-prefetch architecture is combined with an interface designed to
transfer 8 data words per clock cycle at the I/O pins.

Table 1: Micron GDDR and DDR4 DRAM Comparison

Clock Period (tCK) Data Rate (Gb/s) Prefetch

(Burst Number of
Product MAX MIN MIN MAX Density Length) Banks
DDR4 1.25ns 0.625ns 1.6 3.2 4–16Gb 8n 8, 16
GDDR5 20ns 1.00ns 2 8 4–8Gb 8n 16
GDDR6 20ns 0.571ns 2 14 8–16Gb 16n 16

For more information, see the Micron GDDR6 The Next-Generation Graphics DRAM
technical note (TN-ED-03) available on micron.com.

Density
The JEDEC® standard for GDDR6 DRAM defines densities from 8Gb, 12Gb, 16Gb, 24Gb
to 32Gb. At the time of publication of this technical note, Micron supports 8Gb and
16Gb parts.
For applications that require higher density, GDDR6 can operate two devices on a single
channel (see Channel Options later in this document or the Micron GDDR6 data sheet
for details).

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
GDDR6 Overview

Prefetch
Prefetch (burst length) is 16n, double that of GDDR5. GDDR5X was the first GDDR to
change to 16n prefetch, which, along with the 32-bit wide interface, meant an access
granularity of 64 bytes. GDDR6 now allows flexibility in access size by using two 16-bit
channels, each with a separate command and address. This allows each 16-bit channel
to have a 32-byte access granularity — the same as GDDR5.

Frequency
Micron GDDR6N and GDDR6 automotive have been introduced with data rates of 10
Gb/s and 12 Gb/s (per pin). The JEDEC GDDR6 standard does not define AC timing pa-
rameters or clock speeds. Micron GDDR6 is initially available up to 14 Gb/s. Micron's
paper, 16 Gb/s and Beyond with Single-Ended I/O in High-Performance Graphics Memo-
ry, describes GDDR6 DRAM operation up to 16 Gb/s, and the possibility of operating
the data interface as high as 20 Gb/s (demonstrated on the interface only; the memory
array itself was not tested to this speed).
GDDR6 data frequency is 8X the input reference clock and 4X the WCK data clock fre-
quency.

Figure 1: WCK Clocking Frequency and EDC Pin Data Rate Options (Example)

For more information on clocking speeds and options, see the Micron GDDR6 The
Next-Generation Graphics DRAM technical note (TN-ED-03) and the GDDR6N data
sheet (available upon request) on micron.com.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
GDDR6 Overview

Command Address
GDDR6 has a new “packetized” command address (CA) bus. Command and address are
combined into a single, 10-bit interface, operating at double data rate to CK. This elimi-
nates chip select, address strobe, and write enable signals and minimizes the required
CA pin count to 12 per channel (or 16 in pseudo-channel mode). The elimination of a
CS aligns with the point-to-point nature of GDDR memory and reinforces the require-
ment that there is only a single (logical) device per memory interface (single DRAM or
two DRAM back-to-back in byte mode, operating as a single addressable memory).
As shown in the clock diagram, CA operates at double CK. The first half of command/
address is latched on the rising edge, and the second half of command/address is latch-
ed on the falling edge. Refer to the Command Truth Table in the product data sheet for
encoding of each command.
• DDR packetized CA bus CA[9:0] replaces the 15 command address signals used in
GDDR5.
• Command address bus inversion limits the number of CA bits driving low to 5, or 7, in
PC mode.

Bus Inversion
Data bus inversion (DBI) and command address bus inversion (CABI) are enabled in
mode register 1. Although optional, DBI and CABI are critical to high-speed signal in-
tegrity and are required for operation at full speed.
DBI is used in GDDR5 as well as DDR4, and CABI leverages address bus inversion (ABI)
from GDDR5. DBI and CABI:
• Drive fewer bits LOW (maximum of half of the bits are driven LOW, including the
DBI_n pin)
• Consume less power (only bits that are driven LOW consume power)
• Result in less noise and better data eye
• Apply to both READ and WRITE operations, which can be enabled separately
READ WRITE
If more than four bits of a byte are LOW: If DBI_n input is LOW, write data is inverted
— Invert output data — Invert data internally before storage
— Drive DBI_n pin LOW
If four or less bits of a byte lane are LOW: If DBI_n input is HIGH, write data is not inver-
— Do not invert output data ted
— Drive DBI_n pin HIGH

CRC Data Link Protection

GDDR6 provides data bus protection in the form of CRC. Micron GDDR6N supports
half data rate EDC function. At half rate, an 8-bit checksum is created per write or read
burst. The checksum uses a similar polynomial as the full data rate option to calculate
two intermediate 8-bit checksums, and then compresses these two into a final 8-bit
checksum. This allows 100% fault detection coverage for random single, double and tri-
ple bit errors, and >99% fault detection for other random errors. The nature of the EDC
signal is such that it is always sourced from DRAM to controller, for both reads and
writes. Due to this, extra care is recommended during PCB design and analysis ensuring
the EDC net is evaluated for both near-end and far-end crosstalk.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
GDDR6 Overview

Banks and Bank Grouping

Refer to Micron product data sheets for currently available speed grades and bank
grouping requirements.
Micron GDDR6 supports bank groups as defined in the JEDEC specification. Bank
groups are enabled through MR3; it is recommended that bank groups are disabled if
not required for the desired frequency of operation. Short timings are supported with-
out bank groups. Enabling bank groups in MR3 will have no benefit, and results in a
small timing penalty by requiring use of tRRDL, tCCDL, tWTRL and tRTPL.
• GDDR6 has 16 banks.
• With bank groups enabled, organized as four bank groups, each comprised of four
sub-banks, per JEDEC.
• Maximum clock frequency with bank groups disabled is (fCKBG). Refer to product
specific data sheets for fCKBG specifications.

VPP Supply
VPP input—added with GDDR5X—is a 1.8V supply that powers the internal word line.
Adding the V PP supply facilitates the V DD transition to 1.35V and 1.25V and provides ad-
ditional power savings. It is worth keeping in mind that IPP values are average currents,
and actual current draw will be narrow pulses in nature. Failure to provide sufficient
power to V PP prevents the DRAM from operating correctly.

VREFC
GDDR6 has the option to use internal V REFC. This method should provide optimum re-
sults with good accuracy as well as allowing adjustability. V REFC has a default level of 0.7
× V DDQ. External V REFC is also acceptable.

VREFD
VREFD is internally generated by the DRAM. V REFD is now independent per data pin and
can be set to any value over a wide range. This means the DRAM controller must set the
DRAM’s V REFD settings to the proper value; thus, V REFD must be trained.

POD I/O Buffers

The I/O buffer is pseudo open drain (POD), as seen in the figure below. By being termi-
nated to V DDQ instead of half of V DDQ, the size and center of the signal swing can be cus-
tom-tailored to each design’s need. POD enables reduced switching current when driv-
ing data since only zeros consume power, and additional switching current savings can
be realized with DBI enabled. An additional benefit with DBI enabled is a reduction in
switching noise resulting in a larger data-eye.
If not configured otherwise, termination and drive strength are automatically calibrated
within the selected range using the ZQ resistor. It is also possible to specify an offset or
disable the automatic calibration. It is expected that the system should perform opti-
mally with auto calibration enabled.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
GDDR6 Overview

Figure 2: Signaling Schemes

SSTL POD15/POD125/POD135

VDDQ VDDQ VDDQ

TX RX TX RX

2 × RTT 60Ω 60Ω

Z Z

2 × RTT 40Ω
VREF = VREF =
0.5 × VDDQ 0.7 × VDDQ

VDDQ VDDQ
VIH
VIH VREF
VREF VIL
VIL

VSSQ VSSQ

Clock Termination
GDDR6 includes the ability to apply ODT on CK_t/CK_c. The clock ODT configuration
is selected at reset initialization. Refer to Device Initialization in the product data sheet
for available modes and requirements. If ODT is not used, the clock signals should be
terminated on the PCB (similar to GDDR5), with CK_t and CK_c terminated independ-
ently (single-ended) to V DDQ.

JTAG Signals
GDDR6 includes boundary scan functionality to assist in testing. It is recommended to
take advantage of this capability if possible in the system. In addition to IO testing,
boundary scan can be used to read device temperature and V REFD values. If there is no
system-wide JTAG, it might be considered to connect JTAG to test points or connector
for possible later use. If unused, the four JTAG signals are ok to float. TDO is High-Z by
default. TMS, TDI, and TCK have internal pull-ups. If pins are connected, a pull-up can
be installed on TMS to help ensure it remains inactive.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 6 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Channel Options

Channel Options
GDDR6 has the flexibility to operate the command and address busses in four different
configurations, allowing the device to be optimized for application-specific require-
ments:
• x16 mode (two independent x16 bit data channels)
• x8 mode (two devices, each with x8 channels, in a back-to-back "clamshell" configu-
ration)
• 2-channel mode (two independent command/address busses)
• Pseudo channel (PC) mode (a single CA bus and combined x32 data bus; similar to
GDDR5 and GDDR5X)
These are configured by pin state during reset initialization (during initialization, the
pins are sampled to configure the options). The controller must meet device setup and
hold times (specified in the data sheet) prior to de-assertion of RESET_n (tATS and
tATH).

x16 Mode/x8 Mode (Clamshell)

GDDR6 standard mode of operation is x16 mode, providing two 16-bit channels. It is al-
so possible to configure the device in a mode that provides two 8-bit wide channels for
clamshell configuration. This option puts each of the clamshell devices into a mode
where only half of each channel is used from each component (hence, the x8 designa-
tion).
• To be used for creating a clamshell (back-to-back) pair of two devices operating as a
single memory.
• Allows for a doubling of density. Two 8Gb devices appear to the controller as a single,
logical 16Gb device with two 16-bite wide channels.
• Configured by state of EDC1_A and EDC0_B, tied to VSS, at the time RESET_n is deas-
serted.
• One byte of each device is disabled and can be left floating (NC). Along with DQs for
the byte, DBI_n is also disabled, in High-Z state.
• Separate WCK must be provided for each byte. (WCK per word cannot be used in this
configuration)

2-Channel Mode/Pseudo Channel Mode

• 2-channel mode is the standard mode of operation for GDDR6. It is expected to re-
turn better performance in most cases.
• Configured by state of CA6_A and CA6_B at the time RESET_n is deasserted.
• The difference in CA bus pin usage between PC mode and 2-channel mode is that 8 of
the 12 CA pins (CKE_n, CA[9:4], CABI_n) are shared between both channels, while on-
ly the other four CA pins (CA[3:0]) are routed separately for each channel (similar to
GDDR5X operation).

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Channel Options

Figure 3: GDDR6 Pins in 2-Channel Mode

DQ[15:0],DBI[1:0]_n,EDC[1:0]
Channel B
WCK0_t/_c,WCK1_t/_c Bytes 0+1
CKE_n,CA[9:0],CABI_n Control B
CK_t/_c
CKE_n,CA[9:0],CABI_n Control A
WCK0_t/_c,WCK1_t/_c
Channel A
DQ[15:0],DBI[1:0]_n,EDC[1:0]
Bytes 0 + 1
GDDR6

Figure 4: GDDR6 Pins in Pseudo Channel Mode

DQ[15:0],DBI[1:0]_n,EDC[1:0]
Channel B
WCK0_t/_c,WCK1_t/_c Bytes 0+1
CA[3:0] Control B
CK_t/_c
CA[3:0]
CKE_n,CA[9:4],CABI_n Control A
WCK0_t/_c,WCK1_t/_c
Channel A
Bytes 0 + 1
DQ[15:0],DBI[1:0]_n,EDC[1:0]
GDDR6

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 8 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Layout and Design Considerations

Layout is one of the key elements of a successfully designed application. The following
sections provide guidance on the most important factors of layout so that if trade-offs
need to be considered, they may be implemented appropriately.

Decoupling
Micron DRAM has on-die capacitance for the core as well as the I/O. It is not necessary
to allocate a capacitor for every pin pair (VDD:VSS, V DDQ); however, basic decoupling is
imperative.
Decoupling prevents the voltage supply from dropping when the DRAM core requires
current, as with a refresh, read, or write. It also provides current during reads for the
output drivers. The core requirements tend to be lower frequency. The output drivers
tend to have higher frequency demands. This means that the DRAM core requires the
decoupling to have larger values, and the output drivers want low inductance in the de-
coupling path but not a significant amount of capacitance. It is acceptable, and fre-
quently optimal for V DD and V DDQ supplies to be shared on the PCB.
One recommendation is to place sufficient capacitance around the DRAM device to
supply the core and output drivers for the I/O. This can be accomplished by placing at
least four capacitors around the device on each corner of the package. Place one of the
capacitors centered in each quarter of the ball grid, or as close as possible (see the De-
coupling Placement Recommendations image). Place these capacitors as close to the
device as practical with the vias located to the device side of the capacitor. For these ap-
plications, the capacitors placed on both sides of the card in the I/O area may be opti-
mized for specific purposes. The larger value primarily supports the DRAM core, and a
smaller value with lower inductance primarily supports I/O. The smaller value should
be sized to provide maximum benefit near the maximum data frequency.
Decide between two values—0.1µF and 1.0µF—for the core. Intermediate values tend to
cost the same as 1.0µF capacitors, which is based on demand and may change over
time. Consider 0.1µF for designs that have significant capacitance away from the DRAM
and a power supply on the same PCB. For designs that are complex or have an isolated
power supply (for example, on another board), use 1.0µF. For the I/O, where inductance
is the basic concern, having a short path with sufficient vias is the main requirement.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 9 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Figure 5: Decoupling Placement Recommendations (shown with DDR4 footprint)

Note: 1. VDD= purple, VSS = green

Power Vias
A DRAM device has four supply pin types: V DD, V SS, V DDQ, and V PP.
The path from the planes to the DRAM balls is important. Providing good, low induc-
tance paths provides the best margin. Therefore, separate vias where possible and pro-
vide as wide of a trace from the via to the DRAM ball as the design permits.
Where there is concern and sufficient room, multiple vias are a preference to minimize
the connection self-inductance. This can be particularly useful at the decoupling cap to
ensure low impedance/self-inductance connection to the respective power and ground
planes. In addition, every power via should be accompanied by a return via to ensure
low mutual inductance between the rails. Keep in mind the loop inductance includes
the self and mutual terms of the via configuration so minimizing loop inductance
should include both terms.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Signal Vias
In most cases, the number of vias in matched lines should be the same. If this is not the
case, the degree of mismatch should be held to a minimum. Vias represent additional
length in the Z direction. The actual length of a via depends on the starting and ending
layers of the current flow. Because all vias are not the same, one value of delay for all
vias is not possible. Inductance and capacitance cause additional delay beyond the de-
lay associated with the length of the via. The inductance and capacitance vary depend-
ing on the starting and ending layers as well as the proximity of the signal to the return
via. This is either complex or labor-intensive and is the reason for trying to match the
number of vias across all matched lines. Vias can be ignored if they are all the same. A
maximum value for delay through a via to consider is 20ps. This number includes a de-
lay based on the Z axis and time allocated to the LC delay. Use a more refined number if
available; this generally requires a 3D solver. Inner layers can be a better choice for the
signal lines, depending on the frequency and the availability of back-drilling. However,
via stubs are usually not recommended.

Return Path
If anything is overlooked, it will be the current return path. This is most important for
terminated signals (parallel termination) since the current flowing through the termina-
tion and back to the source involves higher currents. No board-level (2D) simulators
take this into account. They assume perfect return paths. Most simulators interpret that
an adjacent layer described as a plane is the perfect return path whether it is related to
the signal or not. Some board simulators take into account plane boundaries and gaps
in the plane to a degree. A 3D simulator is required to take into account the correct re-
turn path. These are generally not appropriate for most applications.
Most of the issues with the return path are discovered with visual inspection. The cur-
rent return path is the path of least resistance. This may vary with frequency, so resist-
ance alone may be a good indicator for a preliminary visual inspection check.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Power and Ground Plane Via Stitching

Return, or power draw, paths are essential to the trace loop inductance. It is imperative
that power and ground planes attain minimum possible impedance/inductance. Pro-
vide ample stitching vias in random patterns. Power rail planes will be excited by signal
and power vias transitioning through them, and unless properly stitched, “cavity mode
excitation” will affect high-speed insertion loss and power delivery impedance. The fig-
ure below demonstrates an under-stitched (too few vias connecting power shapes) sce-
nario that should be avoided as it could result in additional inductance and resistance
in the power delivery and signal path return.

Figure 6: Understitching Effect

Trace Length Matching and Propagation Delay

GDDR6, as GDDR5, defines the ability through read and write training sequences for
the controller to individually delay adjust for each DQ, EDC, and DBI pin. GDDR6 con-
troller and PHY must support this delay adjustment to ensure reliable operation. If the
system does not have this ability, it is very difficult to maintain timing simly in PCB
matching. It is also important to consider the timing margin of the board, along with
the abilities of the controller to ensure matching of data, EDC, and DBI signals within a
clock (WCK) group. Refer to data sheet timing requirements.
Prior to designing the card, it is useful to decide how much of the timing budget to allo-
cate to routing mismatch. This can be determined by thinking in terms of time or as a
percentage of the clock period. For example, 1% (±0.5%) at 1.5 GHz is 6.6 ps (±3.3 ps).
Typical inner layer velocity of propagation is about 6.5 ps/mm. Matching to ±0.5mm
(±0.020 inch) allocates 1% of the clock period to route matching. Selecting 0.5mm is
completely arbitrary.
Propagation delay for inner layers and outer layers is different because the effective die-
lectric constant is different. The dielectric constant for the inner layer is defined by the
glass and resin of the PCB. Outer layers have a mix of materials with different dielectric

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

constants. Generally, the materials are the glass and resin of the PCB, the solder mask
that is on the surface, and the air that is above the solder mask. This defines the effec-
tive dielectric for the outer layers and usually amounts to a 10% decrease in propaga-
tion delay for traces on the outer layers. Layer selection should also consider the strip-
line Vs. micro-strip impact on crosstalk. High-speed traces in tight layout spacing con-
straints should be routed as strip-lines to mitigate crosstalk.
When the design has unknowns, it is important to select a tighter matching approach.
Using this approach is not difficult and allows as much margin as is conveniently availa-
ble to allocate to the unknowns. Understanding the capabilities of the controller side
PHY is very important. Know the amount of de-skewing that is available to compensate
for intra line skew, as well as the effects of de-skewing on the power and performance, if
there are trade-offs.

Trace Edge-to-Edge Spacing to Mitigate Crosstalk

For operations up to 16 Gb/s, it is recommended that at least a 3W spacing is main-
tained throughout all adjacent high-speed traces. W is the trace width. The figures be-
low illustrate the effect of edge-to-edge crosstalk as a function of the trace spacing on a
2-inch strip-line sample trace. For proper trace isolation, improved crosstalk, and gen-
eral EMI performance of the design, it is recommended that high-speed traces are rout-
ed as strip-lines referencing a ground on both sides with guard via stitching. Should
guard vias be implemented, the signal-to-signal spacing can be relaxed as needed to fit
layout needs. Guard vias should be placed at a pitch no greater than 1/20 the Nyquist
wavelength. Micron recommends at least -20dB total crosstalk isolation, up to twice the
Nyquist frequency (or at least to the Nyquist frequency).

Figure 7: Trace Edge-to-Edge Spacing

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

High-Speed Via Isolation to Mitigate Crosstalk

Via transitions are a major crosstalk contributor. Proper isolation of the high-speed via
transitions is imperative for improving the channel signal-to-noise ratio.
Blind-via layout is recommended for strip-line trace implementation. Blind vias allow
for proper coaxial isolation of adjacent via transitions. If blind vias are not implemen-
ted, route the high-speed traces as strip-lines on the outer most layers to avoid big
stubs. Stub is a quarter wavelength resonance, and therefore, it dictates the routing lay-
er selection.
For strip-line in an inner or an upper layer, back drilling is recommended. For through-
hole via layout implementation, ensure there is at least one ground via between adja-
cent high speeds. Micron recommends at least -20dB total crosstalk isolation to twice
the Nyquist frequency (or at least the Nyquist frequency). The figures below illustrates
the effect of a ground via (between two signals) on crosstalk.

Figure 8: Ground Via on Crosstalk

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Via Stub Effect on Crosstalk, Insertion and Return Losses

Via stubs can cause various issues in the design if present. They resonate at a quarter
wavelength and dramatically degrade the insertion loss. They are capacitive in nature
(at frequencies below the quarter wavelength) and can affect the return loss and cross-
talk dramatically. They should be eliminated either by routing on the outer layers
and/or back-drilling. Blind vias (outer to inner layer) are also an option to avoid a stub
presence. The figures below demonstrate the effect of the via stubs on return loss, cross-
talk and insertion loss.

Figure 9: Via Stubs on Return Loss, Crosstalk and Insertion Loss

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Via Transition Optimization for Return and Insertion Losses

The high-speed signal via transitions need to be optimized to meet the channel target
impedance requirements. The optimization of the via transition should simultaneously
account for the via anti-pad size and the distance between the signal and ground vias in
the immediate vicinity of the transition (as shown in the figure below). Micron recom-
mends a via transition with no more than a -20dB (|S11|<-20dB). For multi-bus transi-
tions, Micron recommends the placement of the ground via to also help mitigate cross-
talk, as already discussed in the crosstalk mitigation section.
In the image below, the figure to the right illustrates how the aforementioned variables
(in this case, three anti-pad sizes for a given signal to ground via spacing) can be opti-
mized to make the via transition meet the target impedance (in this case 50 Ohm,
shown in red).

Figure 10: Optimizing Via Transitions

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Insertion and Return Loss Improvement: Slot Crossing Elimination

It is important to maintain the minimum possible loop inductance. To help achieve
this, both signal and return path inductances should be kept as low as possible. Slot-
crossings (signal crossing a gap in the reference) increase the return path self-induc-
tance and therefore the trace loop inductance, which will have a profound effect on the
insertion loss high frequency response.
In addition, avoiding slot crossings maintains a better impedance balance throughout
the whole span of the trace, improving the return loss. The figures below illustrate the
effect that even a small slot crossing can have on the insertion and return losses. It is
highly recommended that slot crossings are avoided at any cost.

Figure 11: Slot Crossing on Insertion and Return Losses

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Return Loss Improvement: Signal Trace Neckdowns

Sometimes it helps to reduce the width of the signal trace (neckdown) to route it
through via or pin fields. This type of action will change the impedance of the trace and
therefore will affect the overall trace return loss. If a trace transitions through a capaci-
tive discontinuity, necking up to a certain length of the trace adjacent to that disconti-
nuity, might help the return loss in some frequencies.
Necking a trace for long distances, between two sections of nominal impedance, is not
recommended. The length of the necking is a crucial variable in the decision, so careful
consideration is required to meet your return loss specification. The pictures below il-
lustrate the effect of trace necking in the return loss of the signal. Return loss could po-
tentially affect signal-to-noise ratio and the overall performance of the system.

Figure 12: Trace Necking on Return Loss

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Layout and Design Considerations

Layout and Design Considerations Summary

• Avoid high-speed signals crossing splits in the power and ground planes.
• Separate supplies and/or flip-chip packaging to help prevent controller SSO occur-
rence and the strobe/clock collapses it causes.
• Minimize ISI by keeping impedances matched through the channel (traces, via transi-
tions).
• Minimize crosstalk by isolating high-speed and sensitive bits (such as EDC), and
avoiding return-path discontinuities. Isolation can be affected through strategically
inserted ground vias, controlling signal proximity and routing layer.
• Enhance signaling by matching driver impedance with trace impedance.
• Provide ample via stitching between same power and ground domains on different
layers to minimize plane impedance.
• Provide sufficient return vias in proper proximity to power vias to reduce the power
delivery network loop inductance.
• Although Micron GDDR6N drive strength is 60Ω and 48Ω, it is recommended that the
PCB is routed to 50 Ohms, a commonly compatible impedance value. However,
matching the PCB impedance to the driver strength on the memory and controller
devices will yield best results.
• Properly isolate vias of various power domains.
• Minimize the shared path between power domains (VDD, V DDQ).
• Optimize signal transitions to nominal impedance (50 Ohms).

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Simulations

Simulations
For a new or revised design, Micron strongly recommends simulating I/O performance
at regular intervals (pre- and post- layout for example). Optimizing an interface through
simulation can help decrease noise and increase timing margins before building proto-
types. Issues are often resolved more easily when found in simulation, as opposed to
those found later that require expensive and time-consuming board redesigns or facto-
ry recalls.
Micron has created many types of simulation models to match the different tools in use.
Component simulation models are available. Verifying all simulated conditions is im-
practical, but there are a few key areas to focus on: DC levels, signal slew rates, under-
shoot, overshoot, ringing, and waveform shape.
Also, it is extremely important to verify that the design has sufficient signal-eye open-
ings to meet both timing and AC input voltage levels. For additional general informa-
tion on the simulation process, see the DDR4 SDRAM Point-to-Point Simulation Proc-
ess technical note (TN-46-11) available on micron.com.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Simulations

PCB Stackup
PCB stackup is an important choice that significantly impacts high-speed signal integri-
ty along with power delivery, noise coupling within the system, and noise emissions/
susceptibility concerns. Selecting an appropriate stackup must carefully balance these
factors, providing a low impedance return path, and allowing for the above high-speed
routing recommendations to be implemented.
As a general guideline, implementing an optimum GDDR6 design in fewer than 8 layers
is not recommended as it makes maintaining good design practices more difficult. The
figure below presents a generic example of an 8-layer stackup that could possibly be
used. This is only one option, as their are many variations in 8 layers or greater that can
readily meet the requirements to implement systems using GDDR6 DRAM.
As described in the above design considerations, key points for the stackup are:
• All high-speed nets should remain on the same reference plane (either power or
ground), all the way from the DRAM pin to the controller pin.
• High speed signals should be routed in stripline.
• Back-drilling is recommended.
• If back-drilling is available, route high-speed signals in the first stripline environment
nearest to the packaged component (minimize via transition).
• If back-drilling is not available, consider routing in a stripline environment closer to
the opposite side of the board (minimize via stub beyond routing layer in through-
hole technology).
• Top-layer microstrip routing may provide a via-free alternative, but should be limited
to very short distances and analyzed carefully for crosstalk and delay implications.
• Perform signal integrity simulation to optimize Clock, WCK, CA, DQ termination and
drive strength, being sure to accurately capture the unique impact of EDC on neigh-
boring signals, and vice versa, for both DRAM READ and WRITE operations.
• Perform simulation to optimize on-board decoupling capacitor placement and val-
ues.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Simulations

Figure 13: PCB Stackup – Example of 8 Layers (4 Signal, 4 Power Planes)

Low speed signal (microstrips) 1

0V plane 2

Signal (striplines) 3

Power plane 4

PCB center line

0V plane 5

Signal (offset striplines) 6

Power plane 7

Low speed signal (microstrips) 8

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
References

References
• JESD250A Graphics Double Data Rate (GDDR6) SGRAM standard
• Micron GDDR6 SGRAM Technical Note (TN-ED-03)
• Micron 8Gb GDDR6 SGRAM data sheet (available upon request from micron.com)

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.
 TN-ED-04: GDDR6 Design Guide
Revision History

Revision History
Rev. A – 7/18
• Initial release

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000

www.micron.com/products/support Sales inquiries: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.

CCM005-524338224-10517
tn_ed_04_gddr6_design_guide.pdf - Rev. A 7/18 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2018 Micron Technology, Inc. All rights reserved.