8 7 6 5 4 3 2 1

REVISIONS

ZONE REV. DESCRIPTION DATE APPROVED

27
F
F 24

30 18

30
17 16
2

E E

32
23 20
1 30

34

ITEM NO. PART NUMBER DESCRIPTION QTY.

1 50500-M FT 29X161 1
D
31 D
2 50501 RT 29X161 1
11
3 50402 LOWER SHOCK BOLT M8X39MM 1
26 32 20 6
4 50403 SHOCK BOLT EXPANDER M8X2MM 1 11
5 50404 MAIN PIVOT AXLE 17X84 1 22 29 31 7 28
22
6 50405 MAIN PIVOT SCREW 1 3 19
4
7 50406 MAIN PIVOT SPACER 17X5MM 2
7 15 31
8 50408 DT PIVOT AXLE 151E3 1 14

9 50309 SAG INDICATOR HOLDER 1

5
10 50310 SAG INDICATOR 1

C 11 50411 FLIPCHIP 29X160 2 21 C

12 50512 BONELINK OUTER 120X29 39MM 2 10
13 50513 BONLINK INNER 120X29 39MM 2 31
31
14 50514 DELTA LINK DS 29X160 1
15 50515 DELTA LINK DS 29X160 1
31
16 50516 SEATPOST CLAMP 38.9/34.9E3 1 25
17 50419 REAR HANGER CAP M12 1
8

18 50420 REAR HANGER 12MM BOLT ON 1

33 20
19 50321 WASHER M8X13X0.5 1
12
20 50322 BONELINK BOLT 10 13
B B
21 50323 CSHS M6X20, BLACK 1
13
22 50524 M6X15MM LOW PROFILE SHCS 2 12
20
23 50525 PART DESCRIPTION 1
24 50426 SS PROTECTION 151 1
25 50428 DT PROTECTION 151 1
26 50529 INNER SLIDER PLATE 1
27 50430-170 REAR AXLE BOLT ON 170MM 1
28 50331 UPPER SHOCK BOLT STEEL 1 UNLESS OTHERWISE SPECIFIED: INITIAL DRAWN BY
MAR
29 50433 OUTER SLIDER PLATE 1 TOLERANCES:
1 PL ±0.25 2 PL ±0.05 ANGLE ±.5° INITIAL DRAWN DATE TITLE:
A 1/21/2016 A
30 50341 INTERNAL ROUTING GROMMET 3 INTERPRET DIM AND TOL PER
ASME Y14.5M - 1994 WRECKONING
CHECKED BY
31 Bearing 11197 BEARING 11x19x7MM 6 THIRD ANGLE PROJECTION 161X29 ASSEMBLY
32 Bearing 17x28x9 BEARING 17X28X9 2 PROPRIETARY AND CONFIDENTIAL MATERIAL
XXX
COMMENTS:
SIZE DWG. NO. REV
REAR SHOCK 216X63E3 C 0.0
THE INFORMATION CONTAINED IN THIS
33 mnrp db 216x631 1 DRAWING IS THE SOLE PROPERTY OF
FINISH
50500-00
EVIL-BIKES. ANY REPRODUCTION IN PART XXX
34 Headset No61-66 HEADSET No61-66 1
OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF EVIL-BIKES IS PROHIBITED. DO NOT SCALE DRAWING SCALE: 1:20 WEIGHT: SHEET 1 OF 2
8 7 6 5 4 3 2 1
 8 7 6 5 4 3 2 1

REVISIONS

ZONE REV. DESCRIPTION DATE APPROVED

F
F

E E

D D

C C

B B

UNLESS OTHERWISE SPECIFIED: INITIAL DRAWN BY

MAR
TOLERANCES:
1 PL ±0.25 2 PL ±0.05 ANGLE ±.5° INITIAL DRAWN DATE TITLE:
A 1/21/2016 A
INTERPRET DIM AND TOL PER
ASME Y14.5M - 1994
CHECKED BY
WRECKONING
THIRD ANGLE PROJECTION 161X29 ASSEMBLY
PROPRIETARY AND CONFIDENTIAL MATERIAL COMMENTS:
XXX SIZE DWG. NO. REV

C 0.0
THE INFORMATION CONTAINED IN THIS
FINISH
DRAWING IS THE SOLE PROPERTY OF
EVIL-BIKES. ANY REPRODUCTION IN PART XXX 50500-00
OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF EVIL-BIKES IS PROHIBITED. DO NOT SCALE DRAWING SCALE: 1:20 WEIGHT: SHEET 2 OF 2
8 7 6 5 4 3 2 1