Scribd
Upload
234 views

Code No.C1802 ACC/FCM ECU Fail: Operation

This document provides troubleshooting steps for the DTC C1802 ACC/FCM ECU fail error code. It describes that the ASC-ECU communicates with the ACC/FCM-ECU via CAN bus lines. The error code is set if the ASC-ECU receives an abnormal signal from the ACC/FCM-ECU when the ACC is activated. The troubleshooting process involves checking for issues with the CAN bus wiring, connectors, or a potential malfunction of the ACC/FCM-ECU or ASC-ECU. If the error code remains after checking other systems, the ACC/FCM-ECU should be replaced.

Uploaded by

MaiChiVu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
234 views

Code No.C1802 ACC/FCM ECU Fail: Operation

This document provides troubleshooting steps for the DTC C1802 ACC/FCM ECU fail error code. It describes that the ASC-ECU communicates with the ACC/FCM-ECU via CAN bus lines. The error code is set if the ASC-ECU receives an abnormal signal from the ACC/FCM-ECU when the ACC is activated. The troubleshooting process involves checking for issues with the CAN bus wiring, connectors, or a potential malfunction of the ACC/FCM-ECU or ASC-ECU. If the error code remains after checking other systems, the ACC/FCM-ECU should be replaced.

Uploaded by

MaiChiVu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

35C-DTC C1802 ACC/FCM ECU fail Page 1 of 3

Code No.C1802 ACC/FCM ECU fail

Before replacing the ECU, ensure that the


caution
communication circuit is normal.

OPERATION

The ASC-ECU communicates with the ACC/FCM-


ECU via CAN bus lines.

DTC SET CONDITIONS

If the ASC-ECU receives an abnormal signal from


the ACC/FCM-ECU with the ACC activated, it will
store the DTC.

PROBABLE CAUSES

 Wiring harness or connector failure of CAN


bus line
 Malfunction of ACC/FCM-ECU
 Malfunction of ASC-ECU

DIAGNOSIS

STEP 1. Scan tool (M.U.T.-III)


CAN bus diagnostics

Use scan tool (M.U.T.-III) to diagnose the CAN bus


lines.
Q. Is the check result normal?

Go to Step 2.

https://mitsubishitechinfo.com/data/RE/2014/35/HTML/M135503110001701USA.htm 2014.12.27
35C-DTC C1802 ACC/FCM ECU fail Page 2 of 3

Repair the CAN bus lines (Refer to

GROUP 54C - CAN Bus Diagnostics Table ). On


completion, go to Step 3.

STEP 2. Scan tool (M.U.T.-III)


DTC of other system

Use scan tool (M.U.T.-III) to check that the DTC is


stored in the ACC/FCM-ECU.
Q. Is the DTC stored?

Troubleshoot for the relevant DTC.


Refer to GROUP 17 - Adaptive Cruise Control

System (ACC) .

Go to Step 3.

STEP 3. Check whether the DTC


is stored again.

(1)Erase the DTC.


(2)Ignition switch "LOCK" (OFF)
(3)Ignition switch "ON"
Q. Is DTC No.C1802 stored?

Replace the ACC/FCM-ECU (Refer to


GROUP 17 - Adaptive Cruise Control System (ACC)

). Then go to Step 4.

This diagnosis is complete.

STEP 4. Check whether the DTC


is stored again.

(1)Erase the DTC.


(2)Ignition switch "LOCK" (OFF)
(3)Ignition switch "ON"
Q. Is DTC No.C1802 stored?

https://mitsubishitechinfo.com/data/RE/2014/35/HTML/M135503110001701USA.htm 2014.12.27
35C-DTC C1802 ACC/FCM ECU fail Page 3 of 3

Return to Step 1.

This diagnosis is complete.

https://mitsubishitechinfo.com/data/RE/2014/35/HTML/M135503110001701USA.htm 2014.12.27

You might also like