POWERLOGIC® Power Monitoring and Control Systems

Meter Comparison Table

Enercept Meters Power Meters Circuit Monitors

Feature Value
Basic Enhanced PM600 PM620 PM650 CM2150 CM2250 CM2350 CM2450 CM4000
Phase Current A, B, C, N kq kq k k k k k k k
Volts, L-L A-C, C-B, C-A k k k k k k k k k
Volts, L-N A-N, B-N, C-N k k k k k k k k k
Real Power (kW) A, B, C, total kf kf k k k k k k k k
Reactive Power (kVAR) A, B, C, total kf k k k k k k k k
Apparent Power (kVA) A, B, C, total kf k k k k k k k k
Power Factor (true) A, B, C, total k k k k k k k k k
Frequency k k k k k k k k
Real Energy (kWh) 3Ø total k k k k k k k k k k
Reactive Energy (kVARh) 3Ø total k k k k k k k k
Apparent Energy (kVAh) 3Ø total k k k k k k k k
Energy Accumulation Modes Signed, Absolute, energy in, energy out k k k k k k k k
KYZ Output k k k kp kp kp kp k
Modbus RTU (M) M M M M M M
Communications POWERLOGIC (P) P P P P P P P
Front Display Opt Opt Opt k k k k Opt
THD, Voltage & Current A, B, C k k k k k k k
Current Demand A, B, C, present & peak k k k k k k k
Power Demand kc
(kWd, kVARd, kVAd)) 3Ø total, present & peak k k k k k k k
Date/time stamping Peak demands, power up/restart, resets k k k k k k k
Predicted Power Demand kW, kVAR, kVA k k k k k k
Advanced Demand Options Synch to comms, sliding block calculation k k k k k k
Under/over conditions.
Onboard Alarms phase unbalance conditions k k k k k k
Frequency, current, voltage, power,
Min/Max Readings power factor, THD kj k k k k k k
Data and Event Logs k k k k k k
Downloadable Firmware k k k k k k k k
Waveform Capture Samples per cycle 64 128 128 512
Sag/Swell Detection k k k
Programmable k k
Transient Detection k
Sequence of Events Recording k
Revenue Accuracy, ANSI C12.16 C12.16 C12.16 C12.16 C12.16 C12.16 C12.16 C12.20s
Power/Energy .5% .5% .5% .4% .4% .4% .4% .2%
Accuracy (of Reading) 1% 1%
Current/Voltage .25% .25% .25% .2% .2% .2% .2% .1%
Harmonic Response Based on sample rate 10 10 31 31 31 31 31 31h 31h 127
UL Listed k k k k k k k k k k
CUL k k
CSA, CE, NOM k k k k k k k k
Voltage Input Direct Connect maximum 480 480 600 600 600 180v 180v 180v 180v 600v
CTs Included k k
q Neutral not available
f Total power only. Per phase power unavailable.
p With addition of IOM.
POWER MONITORING AND

j Min/max real power only.

v With addition of PT's unit can monitor up to 1.7MV.
s Plus revenue metering security switch and tab for wire seal.
h Waveform capture up to 63rd harmonic.1. Neutral not available.
c 3 phase total only.
CONTROL
4

© 2000 Square D
4-2 All Rights Reserved 3/00

Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Energy and Enercept Meters
Class 3020, 3050
PowerLogic Energy Meter
The Energy Meter provides the features required for sub-metering along with pricing and convenience that removes the
hurdle from getting the information that is needed to make better decisions. The Energy Meter can be used for tenant
sub-metering applications where the property manager or building owner may not initially desire a full blown energy
management/information system. The Energy Meter can also be used in applications where load dis-aggregation is
required. The Basic Energy Meter acts as a standalone meter with display. The Enhanced Energy Meter adds the
capability of an optional communication board along with voltage input up to 600 Vac.
A multi segment backlit LCD display presents energy consumption in kWh and MWh as applicable. In addition, the
display automatically scrolls through the following variables:
k kW
k KVAR
k PF
k Volts per phase and 3 phase averagec
k Amps per phase and three phase average c
c Per phase values are not displayed on single phase meters.

The compatible current transformers (CT) are split-core style for ease of installation. The CT’s come in 125 A, 225 A,
800 A, 1600 A , and 5000 A ranges. The system accuracy including these compatible CT’s is 1% of reading from 2% to
100% of the rated current of the CT’s.
The Energy Meter has an Infrared Serial port so that data can be retrieved from the meter using a PDA with infrared
capabilities.
Catalog Number Description
EM-B Energy Meter Basic Model
EM-E Energy Meter Enhanced Model
EM-COB Energy Meter Comms Option Board (for Enhanced Model only)
EM-CT01 Energy Meter CT, 125A
EM-CT02 Energy Meter CT, 225A
EM-CT08 Energy Meter CT, 800A
EM-CT16 Energy Meter CT, 1600A
EM-CT50 Energy Meter CT, 5000A

PowerLogic Enercept Meter

Enercept Meters consist of three interconnected split core CT’s with the metering and communication electronics built
into one of the CT housings. Simply snap on the CT’s, connect the voltage inputs and communication lines, and
installation is complete. There are two versions of the Enercept Meter – Basic and Enhanced. They differ only in the
amount of metering information provided. The Basic meter reports power and energy only. The Enhanced version
delivers 26 energy parameters, including power, energy, demand, volts, amps, power factor, and reactive power. Both
versions can be used on either three phase or single phase systems.
Enercept Meters employ the Modbus RTU 2-wire communication protocol and can utilize the same communication
network and POWERLOGIC System Manager software as other POWERLOGIC devices. Data from the Enercept
Meters can be presented within System Manager Software in tabular or graphical format, used for alarming and historical
logging and trending, along with producing reports. This makes the Enercept Meter the perfect unit for sub-metering
your entire facility.
Catalog Number Description Price
B01-2 Enercept Meter, Basic 100 A, 1.25" x 1.51" ID $ 750.
B03-2 Enercept Meter, Basic 300 A, 1.25" x 1.51" ID 773.
B04-3 Enercept Meter, Basic 400 A, 2.45" x 2.89" ID 795.
B08-3 Enercept Meter, Basic 800 A, 2.45" x 2.89" ID 818.
B08-4 Enercept Meter, Basic 800 A, 2.45" x 5.50" ID 840.
B16-4 Enercept Meter, Basic 1600 A, 2.45" x 5.50" ID 863.
B24-4 Enercept Meter, Basic 2400 A, 2.45" x 5.50" ID 885.
E01-2 Enercept Meter, Enhanced 100 A, 1.25" x 1.51" ID 1000.
E03-2 Enercept Meter, Enhanced 300 A, 1.25" x 1.51" ID 1030.
E04-3 Enercept Meter, Enhanced 400 A, 2.45" x 2.89" ID 1060. POWER MONITORING AND
E08-3 Enercept Meter, Enhanced 800 A, 2.45" x 2.89" ID 1090.
E08-4 Enercept Meter, Enhanced 800 A, 2.45" x 5.50" ID 1120.
E16-4 Enercept Meter, Enhanced 1600 A, 2.45" x 5.50" ID 1150.
E24-4 Enercept Meter, Enhanced 2400 A, 2.45" x 5.50" ID 1180.
3050 2W485C 2-Wire only 232-485 Converter 75.
3050 EMBK-3 Enercept Mounting Brackets (Set of 3) 72.
3050 ME-SVR Modem Eserver, Data Logger 676.
CONTROL
4

Discount © 2000 Square D

PL1
3/00 Schedule All Rights Reserved 4-3
Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Monitoring and Control Systems
Metering
Class 3020
Enercept Communications
There are multiple methods for communicating with the
3050 2W485C
Enercept Meter. The Enercept Meter can be tied directly
to a computer, can be tied to an E-Server for data logging,
or can be connected to a POWERLOGIC network with
circuit monitors and power meters.

POWERLOGIC The E-Server is an energy information server that is

PMX or SMS Software perfect for:
k Energy aggregation of remote sites
k Submetering/metering of large facilities
Enercept Meters
k Energy allocation on campuses/bases
It is ideal for remote monitoring applications as it provides
E-Server a flexible, cost effective means to:
k Gather energy usage information from multiple
sources
k Time and date stamp information and store it in
Phone Line
battery backed memory (SRAM)
k Accessible from servers (PCs) via modem or local
RS232
The E-Server accepts inputs from up to 20 Enercept
Meters and consumption pulses from up to four other
sources. The E-Server’s ability to accept standard pulsed
inputs allows for easy integration of energy usage from
water, gas, utility, and sewage meters.

Other Devices

4W-2W Converter

Power Meters
The POWERLOGIC Power Meter is capable of replacing a full complement of basic analog meters. This cost effective,
true RMS meter can operate as a stand-alone device or as part of a POWERLOGIC Power Monitoring and Control
System to help reduce energy and maintenance costs by providing valuable information.
k Certified ANSI C12.16 revenue accuracy Catalog
Description Price
Number
k Display mounts in standard 1% meter cutout
Power Meter Module, Basic Instrumentation PM600 $1129.
k Flexible mounting with separate meter and display Power Meter Module, Basic Instrumentation, plus
Power Meter with Demand, THD, Date/Time Stamping, Neutral PM620 1360.
k Direct connect up to 600 Vac
POWER MONITORING AND

Display Current
k Optional 2-Line LCD Display Power Meter Module, Min/Max, Alarms, Event and PM650 1678.
Data Storage, plus PM-620 Features
k POWERLOGIC & Modbus RS-485 communications
Power Meter Display with 1 Foot Cable PMD32 318.
k 0.25% accuracy on current and voltage Serial cable from PM to Display (4ft) SC104 32.
Serial cable from PM to Display (12ft) SC112 53.
Serial cable from PM to Display (30ft) SC130 101.
k On-board event and data logging
k UL Listed, CSA Approved, CE Marking, NOM
CONTROL

Approved
4

POWERLOGIC is a Registered Trademark of Square D Company or related companies.

© 2000 Square D PL1 Discount

4-4 All Rights Reserved Schedule 3/00

Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Metering
Class 3020, 3090
The POWERLOGIC Circuit Monitor is a multi-function, digital instrumentation, data acquisition and control device
capable of replacing a variety of meters, relays, transducers and other components. Over 50 metered values plus
extensive Min/Max data can be viewed on the six-digit LED display. Each Circuit Monitor offers true RMS metering and
RS-485 communications standard. Models CM-2150 and above offer 0.2% accuracy true RMS metering and other
powerful features such as automatic relay control, waveform capture, on-board event and data logging, and
programmable logic for special applications like custom data logging and control function. On-board memory can be
expanded to add 512K or 1024K to the CM-2150 and above. Optional add-on input/output modules provide status inputs,
a pulse output, relay outputs and analog inputs and outputs.

POWERLOGIC Circuit Monitors

k Certified ANSI C12.16 revenue accuracy
k True RMS Metering through the 31st harmonic
Circuit Monitor k High accuracy: 0.2% on current and voltage
k Power quality readings displayed: THD and K-Factor
k Harmonic Analysis Data through 63rd harmonic
k Automatic Alarm/Relay control
k On-board event and data logging
k Waveform capture
k UL Listed, CSA Approved, CE Marking, NOM Approved
k MV-90 compatible

Circuit Monitors and Accessories, except I/O Options

Class Catalog No. Description Price
3020 CM2150 Circuit monitor with full instrumentation (0.2% accuracy), on-board data logging, 100K memory $2894.
3020 CM2250 Circuit monitor with full instrumentation, CM2150 features, and waveform capture 3869.
3020 CM2350 Circuit monitor with full instrumentation, CM2250 features, and disturbance monitoring 4547.
3020 CM2450 Circuit monitor with full instrumentation, CM2350 features, and programmable logic 5247.
3020 CM2150512K Circuit monitor with full instrumentation (0.2% accuracy), on-board data logging, and 612K memory 3389.
3020 CM2250512K Circuit monitor with full instrumentation, CM2150 features, waveform capture, and 612K memory 4364.
3020 CM2350512K Circuit monitor with full instrumentation, CM2250 features, disturbance monitoring, and 612K memory 5042.
3020 CM2450512K Circuit monitor with full instrumentation, CM2350 features, programmable logic, and 612K memory 5742.
3020 CM21501024K Circuit monitor with full instrumentation (0.2% accuracy), on-board data logging, and 1124K memory 3669.
3020 CM22501024K Circuit monitor with full instrumentation, CM2150 features, waveform capture, and 1124K memory 4644.
3020 CM23501024K Circuit monitor with full instrumentation, CM2250 features, disturbance monitoring, and 1124K memory 5322.
3020 CM24501024K Circuit monitor with full instrumentation, CM2350 features, programmable logic, and 1124K memory 6022.
3020 CM2000U Circuit monitor firmware upgrade kit 245.
3020 CMMEM512K Circuit monitor 512K memory upgrade kit 495.
3020 CMMEM1024K Circuit monitor 1024K memory upgrade kit 775.
3090 VPM277C1 Voltage power module for circuit monitor (Series 2000), 480Y/277 V 231.
3090 CPM48 Control power module for circuit monitor (Series 2000), 18-60 Vdc 648.
3090 RTM317 Ride through module for circuit monitor (Series 2000) 376.
3090 SMA220 Surface-mounting adapter with hinged cover for circuit monitor (CM2000) 178.
3090 CMA100 Mounting collar for circuit monitor (CM2000) 86.
3090 CMA110 CM2000 Mounting adapter with accessory compartment 144.
3090 OCI2000 Front panel optical communications interface for circuit monitor (CM2000) 773.

Input/Output Options for Circuit Monitor

Digital I/O Analog I/O
Catalog
Description Status Pulse Relay 0-5 Vdc 4-20 mA 0-1 mA Price
Number
Inputsq Outputs Outputsc or 4-20 mA Input Output Output
I/O Module with 1 input and 1 output 1 1 – – – – IOM11 $ 198.
I/O Module with 8 inputs and 1 output 8 1 – – – – IOM18 456.
I/O Module with 4 inputs and 4 outputs 4 1 3 – – – IOM44 523.
I/O Module with 2 analog and 8 digital 4 1 3 1 1 – IOM441120 1124.
I/O Module with 2 analog and 8 digital 4 1 3 1 – 1 IOM441101 1124.
I/O Module with 8 analog and 8 digital 4 1 3 4 4 – IOM444420 1712.
I/O Module with 8 analog and 8 digital 4 1 3 4 – 4 IOM444401 1712.
2' I/O Ribbon Cable Extension With Mounting Hardwaref – – – – – – RIO110 114.
CM-2000 Ethernet Communications Modulek – – – – – – ECM2000 1325.
Remote mounted Ethernet Communications Modulek – – – – – – ECMRM 1375. POWER MONITORING AND
q Status inputs can be used as counters, demand synch pulse inputs, and so on.
f Can be used with 3090 CMA-110.
c Form C mechanical relay outputs.
k Supports other POWERLOGIC compatible devices.
CONTROL
4

POWERLOGIC is a Registered Trademark of Square D Company or related companies.

Discount © 2000 Square D

PL1
3/00 Schedule All Rights Reserved 4-5
Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Metering
Class 3020, 3090
The POWERLOGIC Circuit Monitor CM4000 is a multi-function digital metering and monitoring device capable of
replacing a variety of meters, relays, transducers, and other components. Data available for local viewing includes
metered values plus extensive min/max, alarm, and analog/digital input data. Circuit Monitor data is available for viewing
and recording via standard RS-485, RS-232, or optional Ethernet communications. Two 4-line x 20-character display
options are available with user customizable displays. The CM4000 offers 0.1% accuracy, true RMS metering and other
powerful features such as 512 points/cycle waveform capture, sag/swell monitoring, waveshape fault monitoring,
sequence of events recording, and configurable I/O. The CM4000 can be equipped with either the standard current/
voltage module (CVM) for high accuracy metering or the transient detection version of the current/voltage module
(CVM-T) for detecting and recording high speed voltage transients. The CVM-T and the CVM are interchangeable on
any CM4000.

POWERLOGIC Circuit Monitor 4000

k True RMS metering through the 127th harmonic k Field installable digital I/O card
k ANSI C12.20 Revenue Accuracy k Field installable modular analog/digital I/O extender
k Neutral to ground voltage metering k Revenue metering security switch and tab for wire
seal
k Simultaneous communications port operation
k Sag/swell disturbance monitoring
k Standard 1 RS-485 and 1 RS-232 Modbus RTU
communications port (38.4 KBaud) k Waveform capture with up to 512 samples/cycle
k Optional field installable Ethernet Communications k Extended waveform capture (up to 30 sec)
Card with standard web pages k Oscillatory transient detection and recording
k Two option card slots for field installable cards k High speed transient voltage detection and recording
k Wiring diagnostics performed at user request k Sequence of events recording using GPS
k No PT’s required up to 600 V synchronization technology
k Standard 8 Mb of non-volatile memory (field k UL Listed, CSA Approved, CE Marking, NOM
upgradeable) Approved, FCC compliant
k Standard pulse output (KYZ)

POWERLOGIC Circuit Monitor 4000 Optional Displays

k High Visibility remote VF (vacuum fluorescence) k Displays metering data, min/max values, alarms,
display with I/R communications port inputs
k Remote LC (liquid crystal) display with backlighting k Optional user configurable display screens
also available
Circuit Monitor 4000
Description Catalog No. Priceq
Instrumentation, On-board Data Logging Waveform Capture, Disturbance Recording, Configurable I/O, 0.1% Accuracy CM4000
Same as CM-4000 plus Impulsive Transient Detection CM4000T

Accessories for Circuit Monitor 4000

Accessory Catalog No. Priceq
Field installable I/O card with 4 status inputs, 3 relay outputs, and 1 pusle output (KYZ) IOC44
I/O Extender module with 4 analog inputs and 4 analog outputs (4-20 mA) IOX0044
I/O Extender module with 4 status inputs and 4 analog outputs (4-20 mA) IOX0404
I/O Extender module with 8 status inputs IOX08
I/O Extender module with no pre-installed I/Oc IOX
Ethernet Communications Card; 100 Mb Fiber or 10/100 Mb UTP Ethernet port and 1 RS-485 master port ECC21
Current/Voltage module CVM
Current/Voltage module with high speed transient detection CVMT
4-line x 20-character Liquid Crystal Display with backlighting CMD-LC
4-line x 20-character Vacuum Fluorescent Display with I/R port and Proximity Sensor CMD-VF
I/R communications interface for the Vacuum Fluorescent Display OCI-VF
4 foot display cable CAB4
12 foot display cable CAB12
30 foot display cable CAB30
POWER MONITORING AND

q Contact your nearest Square D/Schneider Electric sales office.

c Contact your nearest Square D/Schneider Electric sales office for user-specified I/O options.
CONTROL
4

© 2000 Square D PL1 Discount

4-6 All Rights Reserved Schedule 3/00

Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Trip Systems and Protective Relays
Class 3010, 3030
POWERLOGIC Trip Unit for Low-Voltage Power Circuit Breakers
k Includes all protection features of the standard Digitrip series
k True RMS sensing
k Local readout of metering and diagnostics
k Remote monitoring via data communications at baud rates up to 19,200 bps:
— RMS currents, per-phase and ground
— Demand power and energy
— Breaker status (open/closed/tripped)
— Cause of trip (type, fault magnitude)
— Protective settings and historical information
k Integral to breaker - no external current or potential transformers required
Digitrip RMS 810D k POWERLOGIC System compatibility
k Retrofit options available
The POWERLOGIC trip unit for low-voltage power breakers integrates overcurrent protection, power metering and data
communications into a single, compact unit. Featuring true RMS sensing, the trip unit utilizes the breaker’s current
sensors and integral potential transformer module, simplifying installation and maintenance. POWERLOGIC application
software is available to organize information in a variety of useful formats, and remote control is possible using
programmable controllers or computers.
Contact your nearest Square D/Schneider Electric sales office for prices.

POWERLOGIC Digital Relay

k Three-phase (ANSI 50/51) and ground (50/51N or 50/51G) overcurrent protection
k User-selectable time-current curves
k Local keypad and display of metering and diagnostics
POWERLOGIC k Remote monitoring via data communications at baud rates up to 19,200 bps:
Digital Relay
— RMS currents, per-phase and ground
— Demand currents, per-phase
— Breaker status
— Cause of trip (type, fault magnitude)
k POWERLOGIC System compatibility
k 120 Vac or 48/125 Vdc control power options
The POWERLOGIC Digital Relay accepts current inputs from standard 5-Ampere current transformers and is suitable
for a wide range of applications on medium-voltage circuits. Remote breaker operation is possible using programmable
controllers or computers.
Class 3030 – Protective Relays
Description Catalog No. Price
Digital Overcurrent Protective Relay DR LX S01 X0A TEN $2624.
(Three-Phase and Ground) 120 Vac control power
Digital Overcurrent Protective Relay DR LX S01 X0A TBN 2624.
(Three-Phase and Ground) 48/125 Vdc control power
Digital Overcurrent Protective Relay (Three-Phase and Ground) with data communications, DR LX S01 S0A TEN 3279.
120 Vac control power
Digital Overcurrent Protective Relay (Three-Phase and Ground) with data communications, DR LX S01 S0A TBN 3279.
48/125 Vdc control power
CSH 30 core balance CT ground fault sensor CSH 30 117.
POWER MONITORING AND
CSH 120 core balance CT ground fault sensor CSH 120 254.
CSH 200 core balance CT ground fault sensor CSH 200 419.
Rear Cover for Digital Relay AMT813 207.
CONTROL
4

POWERLOGIC is a Registered Trademark of Square D Company or related companies.

Windows is a Trademark of Microsoft Corporation.

PL1 Discount © 2000 Square D

3/00 Schedule All Rights Reserved 4-7
Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Application Software
Class 3080
Powerful Software Solutions
POWERLOGIC Power Monitoring and Control Systems provide a total,
integrated system approach to power management. Circuit monitors
and Power Meters provide a tremendous amount of data.
POWERLOGIC Application Software turns that data into powerful,
useful power monitoring information.
Power Information Anytime, Anywhere
k Microsoft Windows NT®/Windows® 98 software packages
k Easy-to-use–designed with power system engineer in mind
k Flexible architecture, from stand-alone PC to client/server
k Real-time viewing with customization
k Data sharing with ODBC database and client/server DDE over
network as well as Active X/DCOM optional custom solutions

Reads DDE Data from other Applications

Shares SMS Data through DDE on Client

Communicate to Multiple Devices
Communicate to Single Devices
Monitor Multiple Device Types
Real-Time Displays

Set-up Devices and Routing

Create Graphical Drawings

Supports Network Clients
System Manager™ software offers a variety of predefined and
customizable real-time data displays.

Waveform Capture
Real-Time Tables

Automatic Tasks
Manual Control

Customization
Supports GFX

Meter Panels
Bar Charts

Trending
Logging

Reports
Alarm
Application Software Feature Comparison
Class 3080 Catalog Windows Description PL Server PL Client
Product Name Number Platform
Includes POWERLOGIC network server and one SMS client.
The POWERLOGIC network server must be located on the PC
System Manager
Client/Ser. SMS3000 NT that is connected to the device network for polling and then x x x x x x x x x x x x x x x x x x
NT Client/Server serving the data to client applications over the distributed PC
LAN or on the same PC.c
The client application displays information collected by a
System Manager SMS1000 NT/98 POWERLOGIC network server. The client application must be x x x x x x x x x x x x x
Client used with SMS-3000.
Add-On The client application displays information collected by a
Interactive POWERLOGIC network server. The client application must be
Graphics GFX1000 NT/98 used with either SMS-3000, SMS-1500, or PMX-1500. x x x x x x x x
Client Note: Must be on same PC when used with SMS-1500,
PMX-1500 or SMS-121
Stand-alone POWERLOGIC power monitoring application
System Manager which communicates to devices and displays information
SMS1500 NT/98
Stand-alone collected on the same PC. GFX is optional but must be located x x x x x x x x x x x x x x x x x
on the same PC. No support for additional clients.
Stand-alone POWERLOGIC power monitoring application
Power Monitoring
Stand-alone EXPlorer which communicates to devices and displays information
PMX1500 NT/98 x x x x x x x x x x x x
collected on the same PC. GFX is optional but must be located
Stand-alone on the same PC. No support for additional clients.
Stand-alone POWERLOGIC monitoring application which
System Manager communicates to one device route only, any device type, any
One-to-One SMS121 NT/98 x x x x x x x x x x x x x x x x x
supported communication method. GFX is optional but must be
Stand-alone located in the same PC. No support for additional clients.
c Number of connected clients is dependent upon Windows NT version purchased. NT Workstation allows 10 clients. NT Server allows unlimited clients. DDE is counted as a connected client.

New Features Available in System Manager Version 3.1

k Advanced waveform display and harmonic capabilities, including: k Modbus protocol support
– Harmonic data spectral plot through the 63rd harmonic for quick – Open communications allowing compatibility with Modbus
POWER MONITORING AND

analysis of circuit harmonics speaking devices

– Waveform capture overlays to easily compare phase k Enhanced compatibility with other software applications
relationships
– Zooming control and selection of waveform sections for in depth k Support non-electrical utility monitoring, such as gas, water, and
analysis steam, with proper scaling and units
k Virtual circuit node feature allows you to report and record sums, k Tri-lingual language support
differences or percentages of real-time monitored values.
CONTROL

– Combine data from multiple devices.

– Provides accurate cost allocation for departments and facilities.
– Help avoid peak demands when there are multiple mains without
a summation meter
4

POWERLOGIC is a Registered Trademark of Square D Company or related companies.

System Manager is a Trademark of Square D Company or related companies.
NT/Windows is a Trademark of Microsoft Corporation.

© 2000 Square D
4-8 All Rights Reserved 3/00

Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Application Software
Class 3080
POWERLOGIC Application Software
Description s Catalog Number Price
System Manager™ Client/Server, Windows NT SMS3000q t
System Manager Client, Windows NT/98 SMS1000c t
Interactive Graphics Client, Windows NT/98 GFX1000j $ 3600.
System Manager Standalone, Windows NT/98 SMS1500q t
Power Monitoring EXPlorer, Windows NT/98 PMX1500q 4500.
System Manager One-to-One, Windows NT/98 SMS121q 1850.
POWERLOGIC Ethernet Driver for SMS-3000 Software Family TCPMMS 950.
q Requires RS232/RS485 converter or Ethernet Comms. Card.
c Requires 3080 SMS3000.
Disturbance Monitoring j Requires 3080 SMS3000 or SMS1500 or PMX1500 or SMS121.
t Contact your nearest Square D/Schneider Electric sales office for pricing.
Capture waveforms to analyze power disturbances. q Network card required only for remote client applications and Ethernet communication to device network.

Minimum System Requirements

The Square D POWERLOGIC application software requires a computer system with
certain minimum requirements (see table below). For your convenience, Square D also
offers complete computer systems which include all hardware and software required to
meet your operating needs. Please refer to POWERLOGIC Workstations on page 4-12.
The table below lists the minimum system requirements. The hard disk requirements for
Windows, other software, and logging, memory should also be considered when
choosing a computer.
Note: Users can select any number of quantities to log. Therefore, the hard disk space
required is dependent upon the number of quantities logged.
Windows NT/98
SMS-3000a SMS-3000
PMX-1500 PMX-1500
SMS-1500 SMS-1500
SMS-121 SMS-121
Windows NTf Windows NTf
Operating System Windows 98 Windows 98
Interactive Graphics (GFX-1000) VGA VGA
Display Mode (Super VGA recommended) (Super VGA recommended)
Display system-wide information on drawings such as
486/66
one-line diagrams, front elevations, or site plans. Model Pentium (Pentium recommended)
64M 64M
RAM (128M recommended) (128M recommended)
Hard Disk 500Mp 500Mp
Program Size 50M c 50M c
SY/LINK Card optional ...
RS-232 Port required ...
Network Card t t
Modem 14.4 or 28.8 (optional) ...
Sound Card optional optional
3.5" Drive u u
CD Drive recommended recommended
a SMS-3000 operates on Windows NT only.
f Windows NT, version 4.0 or higher, required in SMS-3000. The other applications run on Windows NT 4.0 or
Windows 98.
p This figure takes into account only what SMS will use. Any additional applications must be considered separately.
The amount of space taken up by SMS on the hard disk depends on whether logging data is stored on the same
computer.
c SMS uses about 8M; the additional is due to system components.
t Required in SMS-3000, to support network clients; optional in other products.
u Required unless CD drive is available.

Additional Software Options

For additional functionality, a Billing Module, SQL Database Module and Pager Module POWER MONITORING AND
are also available. Please contact your nearest Square D/Schneider Electric sales office
for pricing.
CONTROL
4

POWERLOGIC and SY/LINK are Registered Trademarks of Square D Company or related companies.
Windows is a Trademark of Microsoft Corporation.

PL1 Discount © 2000 Square D

3/00 Schedule All Rights Reserved 4-9
Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
System Components and Packaged Systems
Class 3020, 3050, 3070
POWERLOGIC Ethernet Gateway
The POWERLOGIC Ethernet Gateway provides a direct connection to Ethernet-TCP/IP
networks to make power monitoring and power quality information available over new and
existing local and wide area networks. Electrical distribution systems can be better
managed using Ethernet technologies and the Internet.
Class 3050 – POWERLOGIC Ethernet Gateway
Description Type Price
POWERLOGIC Ethernet Gateway–1 port EGW1 $2385.
POWERLOGIC Ethernet Gateway–2 ports EGW2 4028.
POWERLOGIC Ethernet Gateway Mounting Brackets EGWMBK 133.
POWERLOGIC Ethernet Gateway Null Modem Cable EGWNMCl 37.
Ethernet Gateway l One required per job for setup.

POWERLOGIC Ethernet Communication Modules

The POWERLOGIC Ethernet Communication Module (ECM) connects POWERLOGIC
and Modbus/Jbus devices to an industry-standard Ethernet network. The ECM receives,
converts, and transmits data over Ethernet using Modbus TCP/IP protocol to your PC
where the information can be monitored and analyzed with POWERLOGIC System
Manager (SMS) software
Class 3020 – POWERLOGIC Ethernet Communication Modules
Description Catalog No. Price
POWERLOGIC ECM for direct mounting to the back of a Series 2000 ECM2000 $1825.
circuit monitor and without I/O module
POWERLOGIC ECM for remote mounting when circuit monitor is not ECMRM 1875.
present or circuit monitor has on-board I/O module

POWERLOGIC Interface for MICROLOGIC® Circuit Breakers

This interface collects and makes per-phase RMS and ground fault currents, circuit
breaker data and trip setting and historical trip data available to the POWERLOGIC
Ethernet Communication Modules system. A single interface supports up to 8 circuit breakers.

Class 3050 – POWERLOGIC Product Interfaces

Description Catalog No. Price
Product Interface for MICROLOGIC Circuit Breakersq PIF3 $2611.
q Requires 1 CIM3F Communications Adapter per Circuit Breaker.

POWERLOGIC Packaged Systems

POWERLOGIC is a flexible modular system. An easy way to start building a system is
with a Quick Start Kit. These kits contain everything needed to start monitoring power.
They include a Circuit Monitor, application software, and a communications cable.
Class 3070 — Quick Start Kits
Description Catalog No. Price
Quick Start Kit including CM2350, SMS-121 software and OCI QSK2350 $4965.
(3090 OCI2000)

Product Interface for

MICROLOGIC Circuit Breakers
POWER MONITORING AND
CONTROL
4

MICROLOGIC and POWERLOGIC are Registered Trademarks of Square D Company or related companies.

© 2000 Square D PL1 Discount

4-10 All Rights Reserved Schedule 3/00

Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Engineering Services
Class 3000
Power System Studies
The Square D Power System Analysis Group provides expertise in a variety of electrical power system studies. These
studies can improve the reliability, safety and efficiency of all types of electrical systems, leading to long-term cost
savings. For example, a harmonic analysis identifies equipment exposed to destructive harmonics, and provides
solutions to increase product life and avoid damage or failure. System studies can provide economic benefits for small
and large electrical systems, whether new or existing. Some of the more common system studies include:
k Short-Circuit Analysis
k Time-Current Coordination
k Motor Starting / Voltage Drop
k Motor Starting / Torque-Speed Acceleration Analysis
k Safe Motor Re-energization
k Harmonic Analysis
k Transient Analysis
k Power Factor Correction Analysis
k Other System Specific Analysis
For additional information and pricing, contact your nearest Square D/Schneider Electric sales office or write to:
Square D Company, 2365 Harrodsburg Road, Suite B410, Lexington, KY 40504.

Current in Amperes
1000

500 PU-1
FLA

200

100
3-SE Main
10-NE FDR
2-CS3 Fuse
50
T1-ANSI

20
IG-GRD RLY
Time in Seconds

10 1-UTIL RLY
5

2 PMCS Technical Support

1 There are several ways to receive top quality support
.5 on POWERLOGIC and POWERLINK products:
.2 k Phone 615-287-3400
TX INRUSH
.1 X k Fax 615-287-3403
.05 k Email: [email protected]
.02 k D-Fax 800-557-4556 (PM&CS Index is
.01
Document #104)
.5 1 2 5 10 20 50 100 200 500 1000 2000 5000 10000

Time-Current Coordination Studies are just one of the many

power system studies Square D can provide.

POWERLOGIC University
POWERLOGIC University offers a number of courses covering POWERLOGIC and POWERLINK products. Training is
conducted at the product headquarters, providing an opportunity to meet product developers.
POWERLOGIC University
Description Catalog Number Price
POWER MONITORING AND
POWERLOGIC Update Course PLUC210 q
POWERLOGIC Fundamentals (Self Study Course) PLUC120CR q
POWERLINK Fundamentals PLUC110 q
POWERLOGIC System Installation & Maintenance Certification PLUC100 q
Comprehensive POWERLOGIC System PLUC200 q
Comprehensive POWERLOGIC Bundle (2 Courses) PLUC205 q
SMS-3000 Administrator Certification PLUC300 q
CONTROL

Energy Management and Advanced Reporting PLUC230 q

Power Quality with POWERLOGIC Systems PLUC140 q
Customer Site Training PLUCSite q
POWERLOGIC Technical Support CD PLUCD q
POWERLOGIC/POWERLINK Priority Technical Support PSUP100 q
4

q Contact your nearest Square D/Schneider Electric sales office for schedules, course descriptions, and pricing.

POWERLINK, POWERLOGIC, MICROLOGIC and SY/LINK are Registered Trademarks of Square D Company or related companies.

PL1 Discount © 2000 Square D

3/00 Schedule All Rights Reserved 4-11
Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com
 POWERLOGIC® Power Monitoring and Control Systems
Power Management Services
Class 3000
Power Monitoring and Control Systems Power Management Services provides a complete range of design and operational
Power System Integration services including specifying, developing, installing, commissioning, supporting, and
training users of power monitoring and control systems and remote power switching
systems. Engineers maintain expertise in many areas such as communications, personal
computers, protective relaying, automatic control systems, and programmable
controllers.
k System Design and Bill of Material Recommendations
k Remote Power Switching System Design
k Develop Specifications, Drawings, Documentation
k Automatic Control Systems/PLC Ladder Programming, including Load Shed/Peak
Shaving Schemes
k Custom Hardware/Software Solutions
k Third Party Communications Interfaces
k Configured Workstations, User Software Interfaces
k On-Site Installation Assistance, Component Configuration & Startup
k Metering Connection Verification/Testing
k On-Site and Headquarters-based Customer Training
k Troubleshooting Assistance, Support for Hardware and Software Products
k Product Upgrades
Application Engineering can provide k Project Coordination
the total system solution
k Power Monitoring Web Server Systems
Application Engineering
POWERLOGIC Workstations
Catalog
Square D offers a complete systems approach to power Description Price
Number
monitoring. POWERLOGIC Application and Engineering Engineering Services ... q
provides POWERLOGIC Workstations — tested and System Engineering and Project Coordination
approved personal computers completely configured Custom POWERLOGIC Engineering Services Hardware ... q
Personal Computer Workstations, Panels, Enclosures, Interfaces
based on the individual system requirements.
POWERLOGIC Workstations are designed to handle Custom POWERLOGIC Engineering Services Software ... q
Ladder Logic Programming, Graphics, Reports, Macros
large amounts of system information, and provide it to
System Startup - On-site Commissioning ... q
those who need it, when they need it. Workstations placed
PowerLink AS Control Module Programming ... q
in key locations allow plant engineers, operators,
maintenance personnel, and others to make informed Power Quality/Energy Management
decisions using real-time and historical information. Power Quality/Energy Management Engineering Studies ... q
Portable Circuit Monitor
Ordering Information Includes 1 CM2452 Circuit Monitor, VT and CT test leads, communications ... q
cables, canvas bag for leads, instruction bulletin
POWERLOGIC Workstations should be ordered by
Portable Circuit Monitor with built-in 19.2k baud modem,
description by specifying the following: PC hardware ... q
or input/ouput module, or both
(POWERLOGIC can make recommendations if desired), Power Management Remote Monitoring Services ... q
optional equipment such as modems, printers, etc., and q Contact your nearest Square D/Schneider Electric sales office.
software to be installed and configured.
Contact your nearest Square D/Schneider Electric sales
office for pricing.

PMCS Technical Support

There are several ways to receive top quality support
on POWERLOGIC and POWERLINK products:
POWER MONITORING AND

k Phone 615-287-3400
k Fax 615-287-3403
k Email: [email protected]
k D-Fax 800-557-4556 (PM&CS Index is
Document #104)
CONTROL
4

© 2000 Square D PL1 Discount

4-12 All Rights Reserved Schedule 3/00

Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 ! www.stevenengineering.com