GAIA Control Demo Application For iOS: User Guide
GAIA Control Demo Application For iOS: User Guide
NO PUBLIC DISCLOSURE PERMITTED: Please report postings of this document on public servers or websites to:
[email protected].
Restricted Distribution: Not to be distributed to anyone who is not an employee of either Qualcomm Technologies, Inc. or its affiliated
companies without the express approval of Qualcomm Configuration Management.
Not to be used, copied, reproduced, or modified in whole or in part, nor its contents revealed in any manner to others without the express
written permission of Qualcomm Technologies, Inc.
All Qualcomm products mentioned herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. Other product and brand names
may be trademarks or registered trademarks of their respective owners.
This technical data may be subject to U.S. and international export, re-export, or transfer (“export”) laws. Diversion contrary to U.S. and
international law is strictly prohibited.
© 2017-2018 Qualcomm Technologies, Inc. and/or its subsidiaries. All rights reserved.
Revision history
Figures
This document describes how to use the Qualcomm GAIA (Generic Application Interface
Architecture) Control Demo Application for iOS v1.5.
This example application controls an audio device that uses the Qualcomm GAIA protocol to
communicate GAIA features and GATT attributes for other Bluetooth low energy technology
features, over BR/EDR or Bluetooth low energy.
Once the application is launched you will presented with a list of nearby devices.
When connecting to your device for the first time, the pairing mode must be activated on the
audio device for this to succeed.
2. The connected device advertises available Bluetooth Smart services. Tap Update Service:
3. The upgrade file or files uploaded from iTunes are listed. Tap the upgrade file or files
required:
4. If the device supports enhanced transfer rates then these can be configured.
Pressing start will begin the over the air update.
5. Once the upgrade is started a progress and estimated time of completion will be shown.
6. When the upgrade file transfer completes, a prompt shows. Tap OK to continue or tap cancel
to abort the upgrade.
7. After validating the processing of the upgrade, the device reboots. The GAIA Control Demo
Application automatically reconnects with the device when it is ready.
8. Depending on the content of the upgrade file, a few dialog confirmations to continue the
process might appear. Confirm the process to continue the update.
9. The GAIA Control Demo Application confirms when the upgrade file is committed to the
device.
To test the service, connect to your phone and set the alert level:
□ 0x00 = Off
□ 0x01 = Mild and high
Figure 2-5 Set up the alert level with Light Blue software for Mac OSX
The Link Loss alert level defines the strength of the alert on the connected device when the
connection is dropped.
The alert levels are:
None: deactivates the alert when the connection is dropped or lost.
Mild: activates an alert when the connection is dropped or lost.
High: activates the strongest alert when the connection is dropped or lost.
Once the RSSI value drops below the threshold a tone will be triggered.
This screen shows all the information available from the audio device regarding the GATT Heart
Rate Profile:
The heart rate measurement, in beats per minute notified by the device (if supported).
The energy accumulated since the last reset of the device known as energy expended, in
kilojoules.
Inform if the body sensor is in contact with the user (if known). The last RR intervals sent
by the device.
The location of the body sensor.
When this screen is displayed, the application automatically subscribes to the notifications of the
GATT Heart Rate Profile. As per the profile specification, the device notifies this information
regularly. The application unsubscribes when the user kills the application or when the user
comes back to the main view.
2.7.3 TWS
Each speaker related to the connected device appears and the speaker mode can be controlled: stereo,
left channel, right channel, mix, or no mode. Also, the volume of each speaker can be controlled if
supported.
The selection of a speaker as stereo, left, right selects automatically the corresponding mode of
speakers.
2.7.4 Equaliser
2.7.5 User EQ
On this screen it is possible to change the general master gain value of the bank and to
customize the different bands by selecting a filter and changing:
Selecting a filter changes the range of the frequency, quality and gain as shown below.
NOTE: In this document “Application” does not have the meaning given in
the Apple Developer License Agreement.