Scribd
Upload
223 views

Welding Procedure Specification

procedimiento para soldadura tipo de especificaciones y requerimientos para soldar tuberia inoxidable

Uploaded by

Jorge Sanchez
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
223 views

Welding Procedure Specification

procedimiento para soldadura tipo de especificaciones y requerimientos para soldar tuberia inoxidable

Uploaded by

Jorge Sanchez
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Welding procedure specification (WPS)

A welding procedure specification is a written document providing direction to the


welder (or welding operator). It contains all the necessary parameters viz. joints,
base metals, filler metals, positions, preheat, PWHT, gas etc. (including ranges, if
any) under which the welding process must be performed. These parameters are
known as variables (as per ASME Section IX). Three types of variables are
mentioned in the code, these are;

1. Essential Variable
2. Non Essential Variable
3. Suplementar Essential variable

Essential Variables (For WPS – QG-105.1 & QW-251.2): A change in


essential variable is considered to affect the mechanical properties (other than
toughness) of the welded joint. Hence the WPS must be requalified, if the essential
variable is changed.

Supplementary Essential Variables (QG-105.3 & QW-401.1): A change in


the supplementary essential variable will affect the toughness properties of the
joint, heat-affected zone, or base material. Hence supplementary essential variables
become additional essential variables in situations where procedure qualification
requires toughness testing. When procedure qualification does not require the
addition of toughness testing, supplementary essential variables are not applicable.

Nonessential Variables (QG-105.4 & QW-251.3): Nonessential variables are


those in which a change can be made without requalification of the existing WPS,
since it is not considered to affect the mechanical properties of the joint. Though a
change in the nonessential variable doesn’t require requalification of the WPS but
still it should be properly addressed in the welding procedure specification (WPS).

Some basic facts about WPS :

A welding procedure specification shall contain, as a minimum, the specific essential


and nonessential variables that are applicable to the welding process. When the
referencing Code, standard, or specification requires toughness qualification of the
welded joint, then applicable supplementary essential variables shall also be
provided in the WPS.
These variables are listed in tables from QW-252 to QW-257. Please note that for
each welding process, there is a separate table containing the list of all variables.
For example, list of variables (essential, nonessential and supplementary essential)
for Shielded Metal Arc Welding (SMAW) is given in table QW-453.

Please see the below table (Table-1) for a complete list of welding processes and
their corresponding tables for variables (as per ASME Section IX).

Table 1
STEPS TO BE FOLLOWED FOR PREPARATION OF WPS:

First of all, we need to identify the welding process which is to be used for example
weather it’s a SMAW or GMAW or GTAW or any other welding process or it’s a
combination of two or more welding processes. Once the welding process is decided
then we need to see the corresponding table (QW-252 to QW-257) for the complete
list of variables. With the help of the table we can list out all the necessary variables
to be used in our WPS.

Once the minimum variables (essential, nonessential and supplementary variable, if


any) are decided a preliminary WPS (or proposed WPS also known as pWPS) is
prepared.

Based on the proposed WPS, Test coupon (or coupons) is prepared, and the coupon
is welded as per the values (or range) provided in the pWPS. All the real time data
(observed during the welding of test coupon) are recorded.

After successful welding, test coupon (or coupons) is subjected to destructive test,
and if the test coupon (or coupons) meets the minimum code requirement then the
same pWPS is finalized and approved for further job. In case of any change same
procedure is repeated till the test coupon doesn’t meet the minimum code
requirement.

All the real time data during welding of test coupon and destructive test report data
is compiled into one document known as Procedure qualification record (PQR).

After successful preparation of PQR, final WPS is prepared and produced to the
authorized welding inspector for final approval.
IMPORTANT ARTICLES IN ASME SECTION IX

ARTICLE I WELDING GENERAL REQUIREMENTS

QW-150 Tension Tests

QW-153 Acceptance Criteria-Tension Tests

QW-160 Guided-Bend Tests

QW-163 Acceptance Criteria-Guided Bend Tests

QW-171 Toughness Tests

QW-172 Toughness Tests-Drop Weight

QW-180 Fillet-Weld Tests

QW-182 Fracture Tests

QW-183 Macro Examination-Procedure Specimens

ARTICLE II WELDING PROCEDURE QUALIFICATIONS

QW-200 General

QW-210 Preparation of Test Coupon

QW-250 Welding Variables (Refer Table-1)

ARTICLE IV WELDING DATA

QW-400 Variables

QW-401.1 Supplementary Essential Variable (Procedure)

QW-402 Joints

QW-403 Base Metal


QW-404 Filler Metal

QW-405 Position

QW-406 Preheat

QW-407 Post Weld Heat Treatment

QW-408 Gas

QW-409 Electrical Characteristics

QW-410 Technique

QW-420 Base Metal Groupings

Table QW/QB-422 Grouping of Base Metals for Qualification

QW-430 F‐ Numbers

Table QW-432 Grouping of Electrodes and Welding Rods for Qualification

QW-440 Weld Metal Chemical Composition

Table QW-442 A-Numbers Classification of Ferrous Weld Metal Analysis for


Procedure Qualification

QW-450 Specimens

Table QW-451.1 Groove-Weld Tension Tests and Transverse-Bend Tests

Table QW-451.2 Groove-Weld Tension Tests and Longitudinal-Bend Tests

Table QW-451.3 Fillet-Weld Tests

Table QW-451.4 Fillet Welds Qualified by Groove-Weld Tests

QW-461 Positions

QW-461.3 Groove Welds in Plate-Test Positions


QW-461.4 Groove Welds in Pipe-Test Positions

QW-461.5 Fillet Welds in Plate-Test Positions

QW-461.6 Fillet Welds in Pipe-Test Positions

QW-462 Test Specimen Table QW-462.1(a) to QW-462.5(e) Fig QW-463.1(a) to


QW-469.2

QW-470 Etching — Processes and Reagents

ARTICLE V STANDARD WELDING PR OCEDURE SPECIFICATIONS (SWPSS)

I hope this article will help all welding professionals and freshers. Please give your valuable
feedback. I would like to thank Mr. Goutham Rathinam

(A Weld I & CSWIP 3.1-TWI, UK) for helping me in writing this article. Thank you.

You might also like