Scribd
Upload
346 views

86 Section IX Practice Questions-1 PDF

Uploaded by

Michael Albuquerque
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
346 views

86 Section IX Practice Questions-1 PDF

Uploaded by

Michael Albuquerque
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 17
ASME SECTION IX PRACTICE QUESTIONS - T. SCHINDLER ‘COPYRIGHT 1996 T. SCHINDLER AND CODEWEST - ALL RIGHTS RESERVED -D0 NOT COPY OR DISTRIBUTE ALL QUESTIONS ARE CLOSED BOOK ASME SECTION IX PRACTICE QUESTIONS 1. The purpose of the WPS and PQR is to determine that: AA. the welder is qualified B. the base metals are strong enough C. the weldment has the desired properties D. the skill of the welder 2. The WPS lists: ‘A. nonessential variables B. essential variables C. ranges for 1 & 2 above D. all of the above 3. The PQR must lis: A. essential variables B. qualification test & examination results C. supplementary essential variables (when notch toughness is required) D. all of the above ‘4, What is the earliest Edition of Section IX recognized by the current edition? A.1958, B. 1992 c. 1987 D. 1962 5, New Welding Procedure Specifications must meet the Edition and Addenda of Section IX. A.1962 B. current C. 1986 D. 1995 6. Each ‘shall conduct the tests required by Section IX to qualify the WPS's used during the construction, alteration, or repair. ‘A, Welder or welding operator B. Manufacturer or contractor ©. Inspector D. Allof the above . The records of procedure, welder and welding operator qualification must be available to the ‘A, Manufacturer B. Welder C. Authorized Inspector D. Foreman ‘COPYRIGHT 1996-T. SCHINDLER AND CODEWEST - ALL RIGHTS RESERVED -DO NOT COPY OR DISTRIBUTE 1 ASME SECTION IX PRACTICE QUESTIONS - T. SCHINDLER ‘COPYRIGHT 1996- T. SCHINOLER AND CODEWEST- ALL RIGHTS RESERVED -DO NOT COPY OR DISTRIBUTE 8. A welder qualifying with a groove weld in plate in the 4G position is qualified to weld groove welds in plate and pipe over 24°O.D. in at least the positions, A. Vertical B. Flat & horizontal C. Flat & overhead D. Horizontal 9. Awelder qualifying with plate fillet welds in the 3F and 4F positions is qualified to weld groove welds in plate in the positions, A. Flat only B. Flat and horizontal C. Flat and vertical D. None of the above 10. A welder qualifying by making a groove weld on pipe with an O.D. of 3/4" in the 5G position is, qualified to weld groove welds ‘A. 1/2" O.D. Pipe in the overhead position B. 6" O.D. Pipe in the vertical position C. 3/4" O.D. pipe in the horizontal position D. None of the above 411. In general, qualification on groove welds also qualifies a welder to make: A. Stud welds. B. Overhand welds C. Fillet welds D. All of the above 12. Charpy V-notch tests are performed to determine a weldment’s, ‘A. Tensile strength B. Duetlity C. Notch toughness D. All of above 13, A welder making a groove weld using the SAW process on P1 materials may be qualified using radiography. A.True B. False 14, When a tensile specimen breaks in the base metal outside of the weld or fusion line, the strength recorded may be at most ___ below the specified tensile and be accepted. A.3.5% B.5% C.5% D. All of the above ‘COPYRIGHT 1996- T. SCHINDLER AND CODEWEST -ALL RIGHTS RESERVED - DO NOT COPY OR DISTRIBUTE 2 15. 16. 17. 18. 19, 20, 24 22, ASME SECTION IX PRACTICE QUESTIONS - T. SCHINDLER COPYRIGHT 1996-7. SCHINDLER AND CODEWEST - ALL RIGHTS RESERVED -DO NOT COPY OR DISTRIGUTE Guided-bend specimens shall have no open defects in the weld or heat effected zone exceeding ‘measured in any direction on the convex surface of the specimen after Bending. Ae" B. 3/32" c. 1/8" D. None of the above ‘When using radiographs to qualify welders, the acceptance standards used are found in ‘A. ASME Section V B. ASME Section IX C. ASME Section Vill D. The referencing code AWPS must describe: A. Essential variables B. Nonessential variables C. Supplementary essential variables when required for notch toughness D. All of the above APQR must describe ‘A. Nonessential variables B. Essential variables C. Results of Welder Qualification tests D. Project description & NDE methods The must cerlfy the PAR as accurate. A. Inspector B. Manufacturer or contractor C. Welder D. All of the above For the SMAW process. is an essential variable for the WPS. A. Groove design B, Post Weld Heat Treatment ©. Root spacing D. Method of cleaning For the SAW process is an essential variable for the WPS. ‘A. Supplemental powdered filler metal (if used) B. Filler metal diameter C. Preheat maintenance D. Addition or deletion of pening ‘The basic purpose of testing a welder is to establish the welders. ‘A. Knowledge of welding requirements B. Ability to deposit sound weld metal C. mechanical ability to operate equipment D. General attitude toward welding inspectors ‘COPYRIGHT 1996 -7. SCHINDLER AND CODEWEST -ALL RIGHTS RESERVED -DO NOT COPY OR DISTRIBUTE 3

You might also like