Service Information

English
19.05.2000
SI.000.0044

SM 74
Retrofitting the inking unit temperature control

1 Product information

1.1 Priority
IFESI0000044000000990

Priority of the information

This document serves for your information.
min

Tab. 1
A retrofit action is to be carried out on request by the
customer.

1.2 Reason
IFESI0000044000000980

GR MS0100110000001000

On presses of model line SM 74 the inking unit tem-

perature control can be retrofitted if this has not been
done by the factory.
There are three different press versions if the inking
unit temperature control has not yet been retrofitted:

D Presses with preassembled inking unit temper-

ature control. Hoses, rotary tubes and distribu-
tor have been mounted. The collecting pipes to
the temperature control device must still be
connected.
D Presses which have been prepared for the ink-
ing unit temperature control. Hoses, rotary
tubes, distributor and connection material have
been enclosed. The assembly is to be carried
out by the customer.
D Presses which have been prepared for the ink-
ing unit temperature control. Hoses, rotary
tubes and connection material must be ordered
separately. The assembly is to be carried out by
the customer.

Fig. 1 Inking unit temperature control SM 74

A.1
 Service Information
English
19.05.2000
SI.000.0044

2 Corrective actions

2.1 Retrofitting the inking unit temperature control

IFESI0000044000000970

Time required

Under optimum conditions this corrective action

takes approx. 1 day for each printing unit.

2.1.1 Retrofittable presses

Model line as of serial no.

SM 74 as of 2 PUs 620 300
Tab. 2

Note
Presses prior to the above serial num-
ber cannot be retrofitted since they are
not provided with hollow ink distributors
and ink fountain rollers.

2.1.2 Necessary parts

It depends on the version of the press which parts

need to be ordered.
Please indicate the serial number when ordering
parts.
On the basis of the serial number Spare Parts Sales
(Dept. CSL) can identify the press version and find
the right parts.

A.2
 Service Information
English
19.05.2000
SI.000.0044

3 Instruction

3.1 Retrofitting the inking unit temperature control

3.1.1 Mounting the rotary tubes

IFESI0000044000000960

GR MS0100134000000000
Remove the printing unit guard on O.S..
B.S.
ÉÉ 2 Remove the plugs (Fig. 2/1) from the openings

ÉÉ
O.S. 1 of the ink fountain roller and the ink distributors.
C.S.
L.S.
L.M.

Fig. 2 Removing the plugs

3
GR MS0100135000000000

Insert the tube (Fig. 3/1) into the rotary tubes

ÀÀÀ
4 (Fig. 3/3) in such a way that the cheese-headed

ÀÀÀ
screw (Fig. 3/4) locks into the groove (Fig. 3/2)

ÀÀÀ
of the tube.
1
4
ÀÀÀ
Tighten the cheese-headed screw (Fig. 3/4) in
1 such a way that the tube (Fig. 3/1) is fixed.
2
ÀÀÀ
3
4

Fig. 3 Mounting the tube in the rotary tube

A.3
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100143000000000
Insert the rotary tube with pipe (Fig. 4/5) into
the ink fountain roller or the ink distributor
(Fig. 4/3).

Note
Make sure that the end of the pipe
3 (Fig. 4/2) on D.S. is located correctly in
the friction bearing (Fig. 4/1)4.

Screw the rotary tubes (Fig. 4/5) to the ink foun-

5 tain roller or the ink distributor (Fig. 4/3) at the
hexagon nut (Fig. 4/4) and tighten these.

ÂÂ
ÀÀÀ
ÅÅÂÂÂÂÂÂ
ÂÂ
ÀÀÀ
ÅÅÂÂÂÂÂÂ
ÂÂ
ÀÀÀÂÂÂÂÂÂ
ÂÂ
ÂÂ 1 2 3 4 5

A.S. B.S.
D.S. O.S.
C.E. C.S.
L.I. L.S.
L.V. L.M.

Fig. 4 Mounting the rotary tubes

A.4
 Service Information
English
19.05.2000
SI.000.0044

3.1.2 Mounting the connection pieces and hoses

GR MS0100136000000000
1

B.S.
O.S.
C.S.
L.S.
L.M.

Fig. 5 Mounting the connection pieces

Screw in both straight and elbow connection

pieces (Fig. 5/2), the leakage pieces (Fig. 5/3)
and the screw plugs (Fig. 5/1) according to
Fig. 5.

Caution – Press damage! In the case

of leaking threads, temperature con-
trol medium will be discharged.
Seal the threads of the connection
pieces with Teflon tape or a suitable
sealant such as Loctite 243 type D1
(part no. 00.580.1781).

A.5
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100137000000000
Screw the support bolts (Fig. 6/1) to the side
1 2
B.S. frame.
O.S.
Fasten the distributor (Fig. 6/2) to the support
C.S. bolt by means of a cheese-headed screw
L.S. (Fig. 6/3).
L.M. 3

Fig. 6 Mounting the distributor

A.6
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100138000000000
Align the connection pieces according to the
B.S. 1 Table.
O.S.
C.S. Connec-
L.S. tion
L.M. pieces
2
Fig. 7/1 swiveled by 25° towards the guard
6 Fig. 7/2 swiveled by 25° towards the side
frame
5
Fig. 7/3 swiveled by 30° towards the side
frame
4
all parallel to the side frame
the others

Caution – Press damage! In the case

of leaking threads, temperature con-
3 trol medium will be discharged.
Seal the threads of the connection
pieces with Teflon tape or a suitable
sealant such as Loctite 243 type D1
(part no. 00.580.1781).

Install and connect the hoses according to

Fig. 7.

Note
The hoses must not be twisted during
the installation.
Fig. 7 Hose installation

Fasten the hose (Fig. 7/4) to the positions
Fig. 7/5 and Fig. 7/6 by means of cable clips in
such a way that the hoses do not chafe against
each other.

Caution – Press damage! Chafing

hoses may start leaking.
On running presses, make sure that the
hoses do not rub on other parts. If nec-
essary, install more cable clips.

A.7
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100139000000000
Install the leakage hoses (Fig. 8/1) according to
B.S. Fig. 8 and let these dangle downwards.
O.S.
C.S. Note
L.S. During the installation of the leakage
L.M. hoses, make sure that they do not rub
against any moving parts or touch these.

Fig. 8 Installation of leakage hoses

A.8
 Service Information
English
19.05.2000
SI.000.0044

3.1.3 Hose installation on presses with one or two printing units

GR MS0100140000000000
Mounting the hoses and connection pieces

Caution – Press damage! In the case

of leaking threads, temperature con-
trol medium will discharged.
Seal the threads of the connection
2 pieces, the tap and the reducing nipple
1 with Teflon tape or a suitable sealant
such as Loctite 243 type D1 (part no.
00.580.1781).

1 Screw the screwed sockets (Fig. 9/3) and the

reducing nipples (Fig. 9/5) into the tap (Fig. 9/4)
according to Fig. 9.
2 Screw the hose nozzle (Fig. 9/6) into the reduc-
ing nipple (Fig. 9/5).
3 Push the hoses (Fig. 9/1, 9/8) onto the hose
connection (Fig. 9/9), the screwed socket
(Fig. 9/3) and the hose nozzle (Fig. 9/6) accord-
ing to Fig. 9.
4 Fasten the hose clamps (Fig. 9/2, 9/7).
5 Lead the hose pipes (Fig. 9/10) through the
base to the temperature control device towards
10 D.S..

1
2
1
3
2
4

5
1
2
9 6
2
1
7

Fig. 9 Hose installation on a two-colour press

A.9
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100153000000000
Installation of the hoses and connection pieces

Note
Make absolutely sure that the hoses are
installed in exactly the way illustrated in
the drawings.

Fig. 10 Hose installation on a single-colour

press
GR MS0100161000000000

Fig. 11 Hose installation on a two-colour press

A.10
 Service Information
English
19.05.2000
SI.000.0044

3.1.4 Hose installation on presses with more than two printing units

GR MS0100141000000000
1 Mounting the hoses and connection pieces

3 Caution – Press damage! In the case

9 of leaking threads, temperature con-
trol medium will be discharged.
5 Seal the threads of the connection
9 pieces and the tap with Teflon tape or a
suitable sealant such as Loctite 243 type
3
D1 (part no. 00.580.1781).
1
3 1 Screw the screwed sockets (Fig. 12/9) into the
8 taps (Fig. 12/5) according to Fig. 12.
4
2 2 Push the hoses (Fig. 12/1, 12/2) onto the hose
3 connections (Fig. 12/6, 12/7, 12/8) and the
1 screwed sockets (Fig. 12/9) according to
Fig. 12.
3 Fasten the screw clamps (Fig. 12/3, 12/4).
4 Lead the hose pipes (Fig. 12/10) through the
base to the temperature control device towards
D.S..

10
1
3
2 9
4
7 5
4
9
2
2 4 3
1
3
4 2
2 4
6

Fig. 12 Hose installation on a press with more

than two colours

A.11
 Service Information
English
19.05.2000
SI.000.0044

Note
Make absolutely sure that the hoses are
installed in exactly the way illustrated in
the drawings.

GR MS0100154000000000
Fig. 13 Hose installation on a four-colour press

GR MS0100155000000000

Fig. 14 Hose installation on a five-colour press

A.12
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100156000000000
Fig. 15 Hose installation on a six-colour press

GR MS0100157000000000
Fig. 16 Hose installation on a seven-colour press
GR MS0100158000000000

Fig. 17 Hose installation on an eight-colour press

A.13
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100160000000000
Fig. 18 Hose installation on a ten-colour press

A.14
 Service Information
English
19.05.2000
SI.000.0044

3.1.5 Electrical connection and assembly

GR MS0100147000000000
Retrofitting the temperature control device

L11 Wire the motor overload switch 15Q39, the con-

L21 tactor 15K39M and the RC link 15RC39M ac-
L31
15X4:+1
cording to the circuit diagram (Fig. 19).
PE
Connect the cable M39 for the distributor 15X3
15Q39 1 3 5 13
of the central control cabinet to the temperature
control device E39 and connect it.
14 15FEM64
XE:39

2 4 6
15K39M 1 3 5

2 4 6

VSM2–X1:6
PE 15X3
U39 V39 W39

M39

3 7 9 PE E39-X1

E39

Fig. 19 Circuit diagram for the temperature con-

trol device

A.15
 Service Information
English
19.05.2000
SI.000.0044

GR MS0100148000000000
Retrofitting the combination device

L11 During the retrofit action on a combination device,

L21 the central dampening solution supply must first be
L31
15X4:+1
removed. The corresponding motor overload switch
PE 15Q40 must be dismounted.
15Q40 1 3 5 13 Mount the new motor overload switch 15Q40 on
the bus bar and connect it according to Fig. 20.
14 15FEM64
XE:40

Lead the cable from the distributor 15X3 of the
central control cabinet to the combination de-
vice E40 and connect it.
2 4 6
 Connect the cable for the serial interface
(Fig. 20/1) of the combination device to
PE
SVM-X4 of the central control cabinet.
15X3
U40 V40 W40

3 7 9 PE E40-X1

E40

1
SVM-X4

Fig. 20 Circuit diagram for combination device

A.16
 Service Information
English
19.05.2000
SI.000.0044

3.1.6 Start-up with temperature control device FRT-S

GR MS0100145000000000
Connection

Connect the hoses for the supply and return

flow (Fig. 21/1) to the connecting sockets
(Fig. 21/3) by means of hose clamps
4 (Fig. 21/2).
3

Fig. 21 Connecting the temperature control de-

vice FRT-S

A.17
 Service Information
English
19.05.2000
SI.000.0044

GR MS1870007000000000
Adjustments/specified measures
1 D The static filling pressure on both manometers
(Fig. 22/1, 22/2) amounts to 1...1.5 bar.
2
Note
The measurement must be carried out at
standstill of the pump!

D The operation pressure (manometer Fig. 22/2)

at 1.5 bar static filling pressure amounts to
3.0...4.0 bar.

Filling procedure

2 Check all connections and connecting pieces.

3 Connect the hose pipe for fresh water on the
feed cock of the temperature control device.
4 Open the automatic air-relief valves, i. e. the
end covers.
5 Open the taps (Fig. 21/4) for the supply and
return flow.
6 Close the tap (Fig. 23/1) for the ink fountain
Fig. 22 By-pass valve with filling manometers temperature control device.

Note
GR MS0100146000000000

B.S. When the tap is closed (Fig. 23/1) the

O.S. flow towards the ink fountain roller is
C.S. open.
L.S.
L.M.
7 Fill the temperature control device.

Note
For further information on the filling pro-
cedure, please see the Service Informa-
tion SI.000.0042 ”Filling the inking unit
temperature control”.

1 8 Close the water supply when the filling pressure

of both manometers (Fig. 22/1, 22/2) amounts
to 1...1.5 bar.
Fig. 23 Tap
9 Switch on the temperature control device (pump
is running).
ß Vent thoroughly and refill water, if necessary.

Note
The secondary venting procedure takes
place automatically via the air-relief
valves.

A.18
 Service Information
English
19.05.2000
SI.000.0044

GR MS1870008000000000
Adjust the operation pressure at the supply run
1 to 3.0...4.0 bar by means of the by-pass valve
(Fig. 24/1).
2 Note
When the temperature control device is
switched on the manometer (Fig. 24/2)
indicates the operation pressure.

Fig. 24 By-pass valve with filling manometers

A.19
 Service Information
English
19.05.2000
SI.000.0044

3.1.7 Start-up with temperature control device FRT-C/combination device FKT-C

GR MS0100144000000000
Connection

Connect the hoses for the supply and return

flow (Fig. 25/1) to the connecting sockets
(Fig. 25/3) by means of hose clamps
4 (Fig. 25/2).

Fig. 25 Connecting the temperature control de-

vice FRT-C

A.20
 Service Information
English
19.05.2000
SI.000.0044

GR MS1870004000000000
Adjustments/specified measures

D The static filling pressure on both manometers

(Fig. 26/1, 26/2) amounts to 1...1.5 bar.

Note
The measurement must be carried out at
standstill of the pump!

D The following operation pressures (manometer

Fig. 26/2) are applicable at 1.5 bar static filling
pressure:
1
Temperature control device Operation pres-
sure in supply
run
FRT-C 10000 L -H- 50 Hz 6.1 ± 0.2 bar
FRT-C 10000 L -H- 60 Hz 5.3 ± 0.2 bar
FRT-C 12000 L -H- 50 Hz 5.0 ± 0.2 bar
FRT-C 12000 L -H- 60 Hz 5.0 ± 0.2 bar
FRT-C 16000 L -H- 50 Hz 5.7 ± 0.2 bar
2
FRT-C 16000 L -H- 60 Hz 6.2 ± 0.2 bar
Fig. 26 By-pass valve with filling manometers
FRT-C 20000 L -H- 50 Hz 6.2 ± 0.2 bar
FRT-C 20000 L -H- 60 Hz 6.0 ± 0.2 bar
Tab. 3

A.21
 Service Information
English
19.05.2000
SI.000.0044

GR MS1870005000000000
Filling procedure

2 Check all connections and connecting pieces.

3 Connect the hose pipe for fresh water to the
feed cock of the temperature control device.
4 Open the automatic air-relief valves, i. e. the
end covers.
5 Open the taps (Fig. 25/4) for the supply and
return flow.
6 Close the tap (Fig. 28/1) for the ink fountain
temperature control device.

Note
When the tap (Fig. 28/1) is closed the
flow to the ink fountain roller is open.

7 Fill the combination device.

1 Note
For further information on the filling pro-
cedure, please see the Service Informa-
tion SI.000.0042 ”Filling the inking unit
3 2 temperature control”.

Fig. 27 By-pass valve with filling manometers 8 Close the water supply when both manometers
(Fig. 27/1, 27/3) indicate a filling pressure of
GR MS0100146000000000

1...1.5 bar.
B.S. 9 Switch on the combination device (pump is run-
O.S. ning).
C.S.
L.S. ß Vent thoroughly and refill water, if necessary.
L.M.
Note
The secondary venting procedure takes
place automatically via the air-relief
valves.

q Adjust the operation pressure on the by-pass

valve (Fig. 27/2) according to Tab. 3.
1
Note
When the combination device is
Fig. 28 Tap
switched on the manometer (Fig. 27/3)
indicates the operation pressure.
Note
When using the combination device, the
hoses for the dampening solution must
have been connected.

A.22
Service Information
English
19.05.2000
SI.000.0044

This confidential product information by Heidelberger

Druckmaschinen AG is intended exclusively for au-
thorized service personnel. Transmission to third par-
ties is prohibited.
Kindly pass this information on to all competent
members of your Service Department.

HEIDELBERGER DRUCKMASCHINEN AG
Service Documentation (TDS-6)
Fax +49-6221-134-2619
E-Mail: [email protected]

A.23