Scribd
Upload
488 views

USB Firmware Update Instruction Manual: AVR-X3400H

This document provides instructions for updating the firmware of an AVR-X3400H unit using a USB drive when an internet connection is not available. It describes downloading the latest firmware files from Denon's website and unzipping them to the root of a FAT16 or FAT32 formatted USB drive with at least 2GB capacity. It then outlines the step-by-step process of inserting the USB drive, starting the automatic update, and restarting the unit once complete. It notes the update may require an initialisation to reset settings.

Uploaded by

Anonymous vQewJPfVXa
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
488 views

USB Firmware Update Instruction Manual: AVR-X3400H

This document provides instructions for updating the firmware of an AVR-X3400H unit using a USB drive when an internet connection is not available. It describes downloading the latest firmware files from Denon's website and unzipping them to the root of a FAT16 or FAT32 formatted USB drive with at least 2GB capacity. It then outlines the step-by-step process of inserting the USB drive, starting the automatic update, and restarting the unit once complete. It notes the update may require an initialisation to reset settings.

Uploaded by

Anonymous vQewJPfVXa
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

USB Firmware Update Instruction Manual

AVR-X3400H

Please only use the USB update method when there is no internet connection available or the
Internet update method does not work for you. Your unit should not be connected by either wired or
wireless network.

You will need an empty FAT16 or FAT32 formatted USB stick with at least 2GB capacity.
Please download the latest firmware from the Denon firmware download page. First the “HW
COMPONENT” files. They will be in the following format DPMS_AVR-X3400HALL_LEGO_XXX-
XXXXXXXX.zip. Then the “HEOS COMPONENT” files – heos_40.prod_x.xxx.xxx.zip. Unzip the
contents (Please ensure no folders/subfolders are included, only the files themselves) to the root
directory of the USB stick. No other files should be present on the stick.

Please read the following instruction carefully before executing:

NOTE: Remove the LAN cable from this unit when performing updates.

1. Press the power button to power the unit on.


2. Wait for the unit to start up and set the input source to “HEOS Music”.
3. Insert the USB flash drive into the front USB input.
4. The USB update will start automatically with the Standby LED illuminating red.
5. Whenever the update is complete “Updated Completed” will appear on the front display.
The unit will then restart. The resulting HEOS COMPONENT file will then have the extension
.done. To use these files again delete the .done part.
Please note that after USB update an initialisation of the microprocessor may be necessary. This will
result in all settings being erased and the unit may need reconfigured/recalibrated. We recommend
taking note of your setting before updating. You can do the initialisation as shown below:-

1. Switch the AVR-X3400H into standby mode.

2. While pressing the “ZONE2 SOURCE” and “DIMMER” buttons at the same time, power on
this unit. All segments in the FL display are blinking.
3. Release the buttons and wait until the receiver is ready.

If an error occurs with the HEOS COMPONENT firmware we recommend doing a “Firmware factory
restore” in the following way:-

- While holding down the buttons “TUNER PRESET CH-” and “DIMMER” simultaneously power
on the unit.

NOTE: Denon is not responsible for any damages resulting from the inappropriate use of this
firmware or updating the unit in an improper way.

2014 D&M Audiovisual Ltd.


All rights reserved. Reproduction, publication on the Internet or other commercial usage of this software and its
documentation without the express written consent of the rightful owner is forbidden and will be prosecuted by law.

You might also like