Configuring Network

CHAPTERS

1. Overview
2. WAN Configuration
3. LAN Configuration
4. IPTV Configuration
5. MAC Configuration
6. Switch Configuration
7. VLAN Configuration
8. IPv6 Configuration
 This guide applies to:
TL-R470T+ v6 or above, TL-R480T+ v9 or above, TL-R600VPN v4 or above, TL-ER5120 v3 or above, TL-ER6020
v2 or above, TL-ER6120 v3 or above

1 Overview
The Network module provides basic router functions, including WAN connection, DHCP
service, VLAN, IPTV service and more.

1.1 Supported Features

WAN
The router can provide a maximum of four WAN ports. Each WAN port has its own internet
connection, providing link backup and load balancing.

LAN
For LAN configuration, you can configure the LAN IP address and DHCP (Dynamic Host
Configuration Protocol) server. With its DHCP server enabled, the router can automatically
assign IP addresses to hosts in the LAN.

IPTV
IPTV services is based on the Internet protocol, rather than through traditional satellite
signal or cable transmission.

The router supports three kinds of IPTV configuration according to your ISP：
 IPTV based on IGMP.
 IPTV in Bridge mode.
 IPTV in Custom mode.

MAC
You can change the default MAC address of the WAN port or LAN port according to your
needs.

Switch
The router supports some basic switch port management functions, like Port Mirror, Rate
Control, Flow Control and Port Negotiation, to help you to monitor the traffic and manage
the network effectively.
VLAN
The router supports 802.1Q VLAN, which can divide the LAN into multiple VLANs, helping
to manage the network more effectively.

IPv6
You can set up an IPv6 internet connection if your ISP provides IPv6 service.
2 WAN Configuration
You can configure at most four WAN ports. Each WAN port can have its own WAN
connection, providing link backup and load balancing.

To complete WAN configuration, follow these steps:

1) Configure the number of WAN ports.
2) Configure the WAN connection.

2.1 Configuring the Number of WAN Ports

Choose the menu Network > WAN > WAN Mode to load the following page.
Figure 2-1 Configuring the WAN Mode

WAN Mode Specify the number of WAN ports.

1: Configure physical interface 1 as WAN1.

2: Configure physical interface 1 and interface 2 as WAN1 and WAN2 respectively.

3: Configure physical interface 1, interface 2 and interface3 as WAN1, WAN2 and

WAN3 respectively.

4: Configure physical interface 1, interface 2, interface 3 and interface 4 as WAN1,

WAN2, WAN3 and WAN4 respectively.

Note:
• When a WAN port is added, a port-related tab is automatically added; when a WAN port is de-
leted, the port-related tab is automatically deleted.

• The router will reboot after switching the WAN mode.

2.2 Configuring the WAN Connection

The router supports six connection types: Static IP, Dynamic IP, PPPoE, L2TP, PPTP and
BigPond Cable, you can choose one according to the service provided by your ISP.
Static IP: If your ISP provides you with a fixed IP address and the corresponding
parameters, choose Static IP.

Dynamic IP: If your ISP automatically assigns the IP address and the corresponding
parameters, choose Dynamic IP.

PPPoE: If your ISP provides you with a PPPoE account, choose PPPoE.

L2TP: If your ISP provides you with an L2TP account, choose L2TP.

PPTP: If your ISP provides you with a PPTP account, choose PPTP.

BigPond Cable: If your ISP provides you with a BigPond Cable account, choose BigPond
Cable. BigPond Cable is only available for Australian users.

 Configuring the Dynamic IP

Choose the menu Network > WAN > WAN to load the following page.
Figure 2-2 Configuring the Dynamic IP

In the Connection Configuration section, select the connection type as Dynamic IP. Enter
the corresponding parameters and click Save.

Connection Type Choose the connection type as Dynamic IP if your ISP automatically assigns the IP
address.

Host Name Optional. Enter a name for the router. It is null by default.

Upstream Specify the upstream bandwidth of the WAN port. The value configured here is the
Bandwidth upper limit of the “Maximum Upstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

Downstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.
 MTU Specify the MTU (Maximum Transmission Unit) of the WAN port.

MTU is the maximum data unit transmitted in the physical network. When Dynamic
IP is selected, MTU can be set in the range of 576-1500 bytes. The default value is
1500.

Primary/ Optional. Enter the IP address of the DNS server provided by your ISP.
Secondary DNS

VLAN Add the WAN port to a VLAN. Generally, you don’t need to manually configure it
unless required by your ISP.

By default, the WAN port is automatically assigned to a VLAN, and the egress rule of
the VLAN is UNTAG, so the packets are transmitted by the WAN port without VLAN
tags. If you want the WAN port to transmit packets with VLAN tag, you need to create
the corresponding VLAN first and configure its egress rule as TAG, then manually
add the WAN port to that VLAN. To create VLANs, go to Network > VLAN > VLAN.

Note: When using the IPTV function, either in Bridge mode or Custom mode,
the router will automatically create corresponding VLANs after you finished the
configuration, and add port 1 (WAN 1) to the VLANs. Users cannot then manually
select the VLAN that WAN 1 belongs to.

Get IP using The broadcasting requirement may not be supported by a few ISPs. Select this
Unicast DHCP option if you can not get the IP address from your ISP even with a normal network
connection. This option is not required generally.

Connect/ Click the button to active/terminate the connection.

Disconnect

 Configuring the Static IP

Choose the menu Network > WAN > WAN to load the following page.
Figure 2-3 Configuring the Static IP

In Connection Configuration section, select the connection type as Static IP. Enter the
corresponding parameters and click Save.
Connection Type Choose the connection type as Static IP if your ISP has offered you a fixed IP
address.

IP Address Enter the IP address provided by your ISP.

Subnet Mask Enter the subnet mask provided by your ISP.

Default Gateway Enter the default gateway provided by your ISP.

Upstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

Downstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

MTU Specify the MTU (Maximum Transmission Unit) of the WAN port.

MTU is the maximum data unit transmitted in the physical network. When Static IP is
selected, MTU can be set in the range of 576-1500 bytes. The default value is 1500.

Primary/ Optional. Enter the IP address of the DNS server provided by your ISP.
Secondary DNS

VLAN Add the WAN port to a VLAN. Generally, you don’t need to manually configure it
unless required by your ISP.

By default, the WAN port is automatically assigned to a VLAN, and the egress rule of
the VLAN is UNTAG, so the packets are transmitted by the WAN port without VLAN
tags. If you want the WAN port to transmit packets with VLAN tag, you need to create
the corresponding VLAN first and configure its egress rule as TAG, then manually
add the WAN port to that VLAN. To create VLANs, go to Network > VLAN > VLAN.

Note: When using the IPTV function, either in Bridge mode or Custom mode,
the router will automatically create corresponding VLANs after you finished the
configuration, and add port 1 (WAN1) to the VLANs. Users cannot then manually
select the VLAN that WAN 1 belongs to.
 Configuring the PPPoE

Choose the menu Network > WAN > WAN to load the following page.
Figure 2-4 Configuring the PPPoE

In the Connection Configuration section, select the connection type as PPPoE. Enter the
corresponding parameters and click Save.

Connection Type Choose the connection type as PPPoE if your ISP provides you with a PPPoE
account.

Username Enter the PPPoE username provided by your ISP.

Password Enter the PPPoE password provided by your ISP.

Connection Choose the connection mode, including Connect Automatically, Connect Manually
Mode and Time-Based.

Connect Automatically: The router will activate the connection automatically when
the router reboots or the connection is down.

Connect Manually: You can manually activate or terminate the connection.

Time-Based: During the specified period, the router will automatically activate the
connection.

Time Choose the effective time range when the Connection Mode is chosen as Time-
Based. To create the time range, go to Preferences > Time Range > Time Range.

Upstream Specify the upstream bandwidth of the WAN port. The value configured here is the
Bandwidth upper limit of the “Maximum Upstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.
Downstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

MTU Specify the MTU (Maximum Transmission Unit) of the WAN port.

MTU is the maximum data unit transmitted in the physical network. When PPPoE is
selected, MTU can be set in the range of 576-1492 bytes. The default value is 1492.

Service Name Optional. Enter the service name. This parameter is not required unless provided by
your ISP. It is null by default.

Primary/ Optional. Enter the IP address of the DNS server provided by your ISP.
Secondary DNS

VLAN Add the WAN port to a VLAN. Generally, you don’t need to manually configure it
unless required by your ISP.

By default, the WAN port is automatically assigned to a VLAN, and the egress rule of
the VLAN is UNTAG, so the packets are transmitted by the WAN port without VLAN
tags. If you want the WAN port to transmit packets with VLAN tag, you need to create
the corresponding VLAN first and configure its egress rule as TAG, then manually
add the WAN port to that VLAN. To create VLANs, go to Network > VLAN > VLAN.

Note: When using the IPTV function, either in Bridge mode or Custom mode,
the router will automatically create corresponding VLANs after you finished the
configuration, and add port 1 (WAN 1) to the VLANs. Users cannot then manually
select the VLAN that WAN 1 belongs to.

Secondary Secondary connection is required by some ISPs. Select the connection type required
Connection by your ISP.

None: Select this if the secondary connection is not required by your ISP.

Dynamic IP: Select this if your ISP automatically assigns the IP address and subnet
mask for the secondary connection.

Static IP: Select this if your ISP provides you with a fixed IP address and subnet mask
for the secondary connection.

Connect/ Click the button to active/terminate the connection.

Disconnect
 Configuring the L2TP

Choose the menu Network > WAN > WAN to load the following page.
Figure 2-5 Configuring the L2TP

In the Connection Configuration section, select the connection type as L2TP. Enter the
corresponding parameters and click Save.

Connection Type Choose the connection type as L2TP if your ISP provides you with an L2TP account.

Username Enter the L2TP username provided by your ISP.

Password Enter the L2TP password provided by your ISP.

Connection Choose the connection mode, including Connect Automatically, Connect Manually
Mode and Time-Based.

Connect Automatically: The router will activate the connection automatically when
the router reboots or the connection is down.

Connect Manually: You can manually activate or terminate the connection.

Time-Based: During the specified period, the router will automatically activate the
connection.

Time Choose the effective time range when the Connection Mode is chosen as Time-
Based. To create the time range, go to Preferences > Time Range > Time Range.
Upstream Specify the upstream bandwidth of the WAN port. The value configured here is the
Bandwidth upper limit of the “Maximum Upstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

Downstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

MTU Specify the MTU (Maximum Transmission Unit) of the WAN port.

MTU is the maximum data unit transmitted in the physical network. When L2TP is
selected, MTU can be set in the range of 576-1460 bytes. The default value is 1460.

Primary/ Optional. Enter the IP address of the DNS server provided by your ISP.
Secondary DNS

VLAN Add the WAN port to a VLAN. Generally, you don’t need to manually configure it
unless required by your ISP.

By default, the WAN port is automatically assigned to a VLAN, and the egress rule of
the VLAN is UNTAG, so the packets are transmitted by the WAN port without VLAN
tags. If you want the WAN port to transmit packets with VLAN tag, you need to create
the corresponding VLAN first and configure its egress rule as TAG, then manually
add the WAN port to that VLAN. To create VLANs, go to Network > VLAN > VLAN.

Note: When using the IPTV function, either in Bridge mode or Custom mode,
the router will automatically create corresponding VLANs after you finished the
configuration, and add port 1 (WAN 1) to the VLANs. Users cannot then manually
select the VLAN that WAN 1 belongs to.

Secondary Select the secondary connection type provided by your ISP

Connection
The secondary connection is required for L2TP connection. The router will get
some necessary information after the secondary connection succeeded. These
information will be used in the L2TP connection process.

VPN Server/ Enter the VPN Server/Domain Name provided by your ISP.
Domain Name

IP Address Enter the IP address provided by your ISP for the secondary connection.

Subnet Mask Enter the subnet mask provided by your ISP for the secondary connection.

Default Gateway Enter the default gateway provided by your ISP for the secondary connection.

Primary/ Enter the primary/secondary DNS provided by your ISP for the secondary
Secondary DNS connection.

Connect/ Click the button to active/terminate the connection.

Disconnect
 Configuring the PPTP

Choose the menu Network > WAN > WAN to load the following page.
Figure 2-6 Configuring the PPTP

In Connection Configuration section, select the connection type as PPTP. Enter the
corresponding parameters and click Save.

Connection Type Choose the connection type as PPTP if your ISP provides you with a PPTP account.

Username Enter the PPTP username provided by your ISP.

Password Enter the PPTP password provided by your ISP.

Connection Choose the connection mode, including Connect Automatically, Connect Manually
Mode and Time-Based.

Connect Automatically: The router will activate the connection automatically when
the router reboots or the connection is down.

Connect Manually: You can manually activate or terminate the connection.

Time-Based: During the specified period, the router will automatically activate the
connection.

Time Choose the effective time range when the Connection Mode is chosen as Time-
Based. To create the time range, go to Preferences > Time Range > Time Range.
Upstream Specify the upstream bandwidth of the WAN port. The value configured here is the
Bandwidth upper limit of the “Maximum Upstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

Downstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

MTU Specify the MTU (Maximum Transmission Unit) of the WAN port.

MTU is the maximum data unit transmitted in the physical network. When PPTP is
selected, MTU can be set in the range of 576-1420 bytes. The default value is 1420.

Primary/ Optional. Enter the IP address of the DNS server provided by your ISP.
Secondary DNS

VLAN Add the WAN port to a VLAN. Generally, you don’t need to manually configure it
unless required by your ISP.

By default, the WAN port is automatically assigned to a VLAN by default, and the
egress rule of the VLAN is UNTAG, so the packets are transmitted by the WAN port
without VLAN tags. If you want the WAN port to transmit packets with VLAN tag, you
need to create the corresponding VLAN first and configure its egress rule as TAG,
then manually add the WAN port to that VLAN. To create VLANs, go to Network >
VLAN > VLAN.

Note: When using the IPTV function, either in Bridge mode or Custom mode,
the router will automatically create corresponding VLANs after you finished the
configuration, and add port 1 (WAN 1) to the VLANs. Users cannot then manually
select the VLAN that WAN 1 belongs to.

Secondary Select the secondary connection type provided by your ISP

Connection
The secondary connection is required for PPTP connection. The router will get
some necessary information after the secondary connection succeeded. These
information will be used in the PPTP connection process.

VPN Server/ Enter the VPN Server/Domain Name provided by your ISP.
Domain Name

IP Address Enter the IP address provided by your ISP for the secondary connection.

Subnet Mask Enter the subnet mask provided by your ISP for the secondary connection.

Default Gateway Enter the default gateway provided by your ISP for the secondary connection.

Primary/ Enter the primary/secondary DNS provided by your ISP for the secondary
Secondary DNS connection.

Connect/ Click the button to active/terminate the connection.

Disconnect
 Configuring the BigPond Cable

Choose the menu Network > WAN > WAN to load the following page.
Figure 2-7 Configuring the BigPond Cable

In Connection Configuration section, select the connection type as BigPond Cable. Enter
the corresponding parameters and click Save.

Connection Type Choose the connection type as BigPond if your ISP provides you with a BigPond
account.

Username Enter the BigPond username provided by your ISP.

Password Enter the BigPond password provided by your ISP.

Connection Choose the connection mode, including Connect Automatically, Connect Manually
Mode and Time-Based.

Connect Automatically: The router will activate the connection automatically when
the router reboots or the connection is down.

Connect Manually: You can manually activate or terminate the connection.

Time-Based: During the specified period, the router will automatically activate the
connection.

Time Choose the effective time range when the Connection Mode is chosen as Time-
Based. To create the time range, go to Preferences > Time Range > Time Range.

Upstream Specify the upstream bandwidth of the WAN port. The value configured here is the
Bandwidth upper limit of the “Maximum Upstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.

Downstream Specify the downstream bandwidth of the WAN port. The value configured here is the
Bandwidth lower limit of the “Maximum Downstream Bandwidth” on Transmission > Bandwidth
Control > Bandwidth Control page, to make “Bandwidth Control” take effect, please
ensure this parameter is set correctly.
MTU Specify the MTU (Maximum Transmission Unit) of the WAN port.

MTU is the maximum data unit transmitted in the physical network. When BigPond
Cable is selected, MTU can be set in the range of 576-1500 bytes. The default value
is 1500.

Auth.Server Enter the authenticating server’s IP address or hostname.

Auth.Domain Enter the server's domain name suffix (based on your location). For example, nsw.
bigpond.net.au for NSW/ACT, vic.bigpond.net.au for VIC/TAS/WA/SA/NT, or qld.
bigpond.net.au for QLD.

VLAN Add the WAN port to a VLAN. Generally, you don’t need to manually configure it
unless required by your ISP.

By default, the WAN port is automatically assigned to a VLAN, and the egress rule of
the VLAN is UNTAG, so the packets are transmitted by the WAN port without VLAN
tags. If you want the WAN port to transmit packets with VLAN tag, you need to create
the corresponding VLAN first and configure its egress rule as TAG, then manually
add the WAN port to that VLAN. To create VLANs, go to Network > VLAN > VLAN.

Note: When using the IPTV function, either in Bridge mode or Custom mode,
the router will automatically create corresponding VLANs after you finished the
configuration, and add port 1 (WAN 1) to the VLANs. Users cannot then manually
select the VLAN that WAN 1 belongs to.

Connect/ Click the button to active/terminate the connection.

Disconnect
3 LAN Configuration
The LAN port is used to connect to the LAN clients, and works as the default gateway
for these clients. You can configure the DHCP server for the LAN clients, and clients will
automatically be assigned to IP addresses if the method of obtaining IP addresses is set as
“Obtain IP address automatically”.

For LAN configuration, you can:

 Configure the IP address of the LAN port.

 Configure the DHCP server.

3.1 Configuring the IP Address of the LAN Port

Choose the menu Network > LAN > LAN to load the following page.
Figure 3-1 Configuring the LAN IP Address

Enter the IP address of the LAN port, and click Save.

IP Address Enter the IP address of the LAN port.

This IP address is the default gateway of the LAN clients, and the IP addresses of all
the LAN clients should be in the same subnet with this LAN IP address.

Subnet Mask Enter the subnet mask of the LAN port.

Management Specify the management VLAN.

Vlan
If you set a management VLAN here, then only the clients in the specified VLAN can
access and manage the router. The default value is “---“, which means no VLAN is
selected, and any client in the LAN can access and manage the router.
 Note:
• Changing the IP address of LAN port will automatically redirect the browser to the new man-
agement page. If the redirecting failed, please try to reconnect your PC to the router to auto-
matically get a new IP address, or configure a proper static IP address manually.

• Changing the IP address of the LAN port may affect some related functions, like the IP pool of
the DHCP server.

3.2 Configuring the DHCP Server

You can configure an IP address pool for the DHCP server to assign IP addresses. When
clients send requests to the DHCP server, the server will automatically assign IP addresses
and the corresponding parameters to the clients. Moreover, if you want to reserve an IP
address for a certain client, you can use Address Reservation to bind the IP address with
the client’s MAC address, and the bound IP address will always be assigned to that client.

 Configuring the DHCP Server

Choose the menu Network > LAN > DHCP Server to load the following page.
Figure 3-2 Configuring the DHCP Server

Configure the parameters of the DHCP server, then click Save.

 Starting IP Enter the starting IP address of the DHCP server’s IP pool. The IP pool defines the IP
Address range that can be assigned to the clients in the LAN.

Note: The starting IP address should be in the same subnet with the IP address of the
LAN port.

Ending IP Enter the ending IP address of the DHCP server’s IP pool. The ending IP address
Address should be greater than the starting IP address.

Note: The ending IP address should be in the same subnet with the IP address of the
LAN port.

Lease Time Specify the lease time for DHCP clients.

Lease time defines how long the clients can use the IP address assigned by the DHCP
server. Generally, the client will automatically request the DHCP server for extending
the lease time before the lease expired. If the request failed, the client will have to stop
using that IP address when the lease finally expired, and try to get a new IP address
from the other DHCP servers.

Default Gateway Optional. It is recommended to enter the IP address of the LAN port.

Default Domain Optional. Enter the domain name of your network.

Primary/ Optional. Enter the DNS server address provided by your ISP. If you are not clear,
Secondary DNS please consult your ISP.

Option60 Optional. Specify the option 60 for device identification. Mostly it is used under the
scenario where the clients apply for different IP addresses from different servers
according to the needs. By default, it is TP-LINK.

If a client requests option 60, the server will respond a packet containing the option
60 configured here. And then the client will compare the received option 60 with its
own. If they are the same, the client will accept the IP address assigned by the server,
otherwise the assigned IP address will not be accepted.

Option 138 Optional. Specify the option 138, which can be configured as the management IP
address of an AC (Access Controller) device. If the APs in the local network request
this option, the server will respond a packet containing this option to inform the APs
of the AC’s IP address.

Status Check the box to enable the DHCP server.

 Configuring the Address Reservation

Choose the menu Network > LAN > Address Reservation and click Add to load the
following page.
 Figure 3-3 Configuring the Address Reservation

Enter the MAC address of the client and the IP address to be reserved, then click OK.

MAC Address Enter the MAC address of the client.

IP Address Enter the IP address to be reserved.

Description Optional. Enter a brief description for the entry. Up to 32 characters can be entered.

Export to IP- Optional. Check the box to export this binding entry to IP-MAC Binding List on Firewall
MAC Binding > Anti ARP Spoofing > IP-MAC Binding page.

Status Check the box to enable this entry.

3.3 Viewing the DHCP Client List

Choose the menu Network > LAN > DHCP Client List to load the following page.
Figure 3-4 Viewing the DHCP Client List

Here you can view the DHCP client list.

Client Name Displays the name of the client.

MAC Address Displays the MAC address of the client.

Assigned IP Displays the IP address assigned to the client.

Address

Lease Time Displays the remaining lease time of the assigned IP address. After the lease expires,
the IP address will be re-assigned.
4 IPTV Configuration
You can configure IPTV according to the type of IPTV service provided by your ISP:

 Configure IPTV based on IGMP.

 Configure IPTV in Bridge mode.

 Configure IPTV in Custom mode.

4.1 Configuring IPTV Based on IGMP

Some ISPs provide IPTV service based on IGMP technology. In this scenario, you can just
enable IGMP snooping and IGMP proxy, and connect your STB (Set-Top Box) to any LAN
port of the router. The IPTV stream will then be transmitted to the corresponding LAN port.

Choose the menu Network > IPTV> IPTV to load the following page.
Figure 4-1 Configuring IPTV Based on IGMP

Enable IGMP Snooping and IGMP Proxy, and choose the IGMP version, then click Save.

IGMP Snooping Check the box to enable IGMP Snooping.

Without IGMP Snooping, the router will broadcast multicast stream to all LAN ports,
even though some LAN ports are not connected to any multicast member.

With IGMP Snooping enabled, the LAN ports listen IGMP packets transmitted between
the router and the clients and build a multicast table. The multicast table records the
multicast members and the corresponding connected LAN port. So the multicast
stream will be transmitted to only the ports that connected to multicast members.

IGMP Proxy Check the box to enable IGMP Proxy.

IGMP Proxy sends IGMP querier packets to the LAN ports to detect if there is any
multicast member connected to the LAN ports.

IGMP Version Choose the IGMP version as V2 or V3. The default is IGMP V2.
4.2 Configuring IPTV in Bridge Mode

If your ISP doesn’t provide any parameters and the IPTV service is not based on IGMP
technology, you can enable IPTV function and choose the Bridge mode, then specify a port
to connect IPTV set-top box.

Choose the menu Network > IPTV> IPTV to load the following page.
Figure 4-2 Configuring the Bridge Mode

Enable IPTV function, choose the mode as Bridge, and choose a LAN port to connect to the
IPTV set-top box, then click Save.

IPTV Check the box to enable IPTV function.

Mode Choose the mode as Bridge.

In Bridge mode, the LAN port chosen to connect to the IPTV becomes a dedicated
port for IPTV service.

Port Mode Specify the service to be supported by the LAN port.

Internet: Specify the port to support only internet service. If you want to access the
internet, you should connect your host to this port.

IPTV: Specify the port to only support IPTV service. If you want to use IPTV, you
should connnect your IPTV set-top box to this port.

4.3 Configuring IPTV in Custom Mode

If your ISP supports Triple-Play service, i.e., providing internet, VoIP and IPTV services over
one single broadband connection, you can configure IPTV in Custom mode.

In Triple-Play, services are labeled with different VLAN tags specified by the ISP. When
the WAN port receives packets, it will forward the packets to the corresponding LAN port
according to the VLAN tag.

Choose the menu Network > IPTV> IPTV to load the following page.
Figure 4-3 Configuring the Custom Mode

Follow these steps to configure IPTV in Custom mode:

1) Enable IPTV function and choose the mode as Custom.

IPTV Check the box to enable IPTV function.

Mode Choose the mode as Custom.

In Custom mode, the services are labeled with different VLAN tags, which is
specified by the ISP. The WAN port will forward the packets to its corresponding
LAN port.

2) Enter the parameters provided by your ISP, including the VLAN IDs and priorities of
different services.

Internet VLAN ID Enter the VLAN ID of the internet service. It is provided by your ISP.

Internet VLAN Enter the VLAN priority of the internet service. It is provided by your ISP.
Priority

802.1Q Tag Optional. Check the box and the egress internet packets of WAN 1 port will be
tagged.

IP-Phone VLAN Enter the VLAN ID of the IP-Phone service. It is provided by your ISP.
ID

IP-Phone VLAN Enter the VLAN priority of the IP-Phone service. It is provided by your ISP.
Priority

IPTV VLAN ID Enter the VLAN ID of the IPTV service. It is provided by your ISP.
 IPTV VLAN Enter the VLAN priority of the IPTV service. It is provided by your ISP.
Priority

IPTV Multicast Enter the VLAN ID of the IPTV multicast service. It is provided by your ISP.
VLAN ID

IPTV Multicast Enter the VLAN priority of the IPTV multicast service. It is provided by your ISP.
VLAN Priority

3) Specify the service to support for the LAN port.

Port Mode Specify the service to be supported by the LAN port.

Internet: Specify the port to support only Internet service. If you want to surf the
internet, you should connect your host to this port.

IP-Phone: Specify the port to support only IP-Phone service. If you want to make
an IP-Phone call, you should connect your IP-Phone to this port.

IPTV: Specify the port to only support IPTV service. If you want to use IPTV, you
should connnect your IPTV set-top box to this port.

Note:
• Among the WAN ports, only WAN 1 supports IPTV service. So if you want to use IPTV function,
connect your ISP network to WAN 1.

• In Bridge mode, after you have saved the configuration, the router will automatically and ran-
domly create some VLANs for WAN 1 and the LAN ports. These VLANs will be displayed on the
VLAN page.

• In Custom mode, after you configured the VLAN IDs of different services, these VLANs will
automatically be created, and port 1 (WAN 1) will automatically be added to the IPTV VLAN and
Internet VLAN. These VLANs will be displayed on the VLAN page.
5 MAC Configuration
Generally, the MAC address does not need to be changed. However, in some particular
situations, you may need to change the MAC address of the WAN port or LAN port.

 Configure the MAC Address of the WAN port

In the condition that your ISP has bound the account to the MAC address of the dial-up
device, if you want to replace the dial-up device with this router, you can just set the MAC
address of this router’s WAN port as the same as that of the previous dial-up device for a
normal internet connection.

 Configure the MAC Address of the LAN port

In a complex network with all the devices are ARP bound , if you want to replace the current
router with this router, you can just set the MAC address of this router’s LAN port as the
same as that of the previous router, which can avoid all the devices under this network
node to update their ARP binding tables.

5.1 Configuring MAC Address

Choose the menu Network > MAC > MAC to load the following page.
Figure 5-1 Configuring MAC Address

Configure the MAC address of the WAN port or LAN port according to your need, then click
Save.

Interface Name Displays the WAN port and LAN port.

Current MAC Configure the MAC address of the WAN port or LAN port.
Address
MAC Clone Restore Factory MAC: Click this button to restore the MAC address to the factory
default value.

Clone Current PC’s MAC: Click this button to clone the MAC address of the PC you
are currently using to configure the router. It’s only available for the WAN ports.

Note:
To avoid a MAC address conflict in the LAN, it is not permitted to set the MAC address of the router’s
LAN port as the MAC address of the current management PC.
6 Switch Configuration
The router provides some basic switch port management function, including Statistics,
Port Mirror, Port Config and Port Status.

6.1 Viewing the Statistics

Choose the menu Network > Switch > Statistics to load the following page.
Figure 6-1 Viewing the Statistics

Statistics displays the detailed traffic information of each port, which allows you to monitor
the traffic and locate faults promptly.

Unicast Displays the number of normal unicast packets received or transmitted on the port.

Broadcast Displays the number of normal broadcast packets received or transmitted on the port.

Pause Displays the number of flow control frames received or transmitted on the port.

Multicast Displays the number of normal multicast packets received or transmitted on the port.
 Total Displays the total bytes of the received or transmitted packets (including error
frames).

Undersize Displays the number of received packets which have a length less than 64 bytes
(including error frames).

Normal Displays the number of received packets which have length between 64 bytes and the
maximum frame length (including error frames).

Oversize Displays the number of received packets that have a length greater than the maximum
frame length (including error frames).

Note:
Error Frame: The frames that have a false checksum.

Maximum frame length: The maximum frame length supported by the router. For untagged frames,
it’s 1518 bytes long; for tagged packets, it’s 1522 bytes long.

6.2 Configuring Port Mirror

Port Mirror function allows the switch to forward packet copies of the monitored port(s) to
a specific monitoring port. Then you can analyze the copied packets to monitor network
traffic and troubleshoot network problems.

Choose the menu Network > Switch > Mirror to load the following page.
Figure 6-2 Configuring Port Mirror

Follow these steps to configure Port Mirror:

1) In Settings section, enable Port Mirror function, and choose the mirror mode.
 Enable Port Check the box to enable Port Mirror function.
Mirror

Mirror Mode Choose the mirror mode which includes Ingress, Egress and Ingress and Egress.

Ingress: The packets received by the mirrored port will be copied to the mirroring
port.

Egress: The packets sent by the mirrored port will be copied to the mirroring port.

Ingress and Egress: Both the incoming and outgoing packets through the
mirrored port will be copied to the mirroring port.

2) In the Monitor List section, set the mirroring port and the mirrored port(s), then click
Save.

Mirroring Port The packets through the mirrored port will be copied to this port.

Usually, the mirroring port is connected to a data diagnose device, which is used
to analyze the mirrored packets for monitoring and troubleshooting the network.

Mirrored Port The packets through this port will be copied to the mirroring port.

Usually, the mirrored ports are the ports to be monitored.

6.3 Configuring Rate Control

Rate Control enables you to control the traffic rate for the specific packets on each port to
manage your network.

Choose the menu Network > Switch > Rate Control to load the following page.
Figure 6-3 Configuring Rate Control

Choose the port and configure the ingress frames or egress frames limitation, then click
Save.

Ingress Limit Check the box to enable the Ingress Limit feature.
 Ingress Frame Specify the ingress frame type to be limited. It is All Frames by default.
Type
All Frames: The ingress rate of all frames is limited.

Broadcast: The ingress rate of broadcast frames is limited.

Broadcast and Multicast: The ingress rate of broadcast and multicast frames is
limited.

Ingress Rate Specify the limit rate for the ingress packets.
(Mbps)

Egress Limit Check the box to enable Egress Limit feature.

Egress Rate Specify the limit rate for the egress packets.
(Mbps)

6.4 Configuring Port Config

You can configure the flow control and negotiation mode for the port.

Choose the menu Network > Switch > Port Config to load the following page.
Figure 6-4 Configuring Flow Control and Negotiation

Configure the flow control and negotiation mode for a port.

Flow Control Check the box to enable the flow control function.

Flow Control is the process of managing the data transmission of the sender to avoid
the receiver getting overloaded.
 Negotiation Select the negotiation mode for the port. You can set the mode as Auto, or manually
Mode set the speed and duplex mode for the port. It is recommended to configure both
devices of a link to work in Auto-Negotiation mode or manually configure them to work
in the same speed and duplex mode.

If the two devices at both sides work in Auto mode, they will advertise their speed and
duplex abilities to each other, and negotiate the optimal speed and duplex mode.

If the local device works in Auto mode while the peer device does not, the local device
will automatically detect and match the speed with the peer device. The local device
will work in half-duplex mode, no matter what duplex mode the peer device is in.

6.5 Viewing Port Status

Choose the menu Network > Switch > Port Status to load the following page.
Figure 6-5 Viewing Port Status

Status Displays the port status.

Link Down: The port is not connected.

Link Up: The port is working normally.

Speed (Mbps) Displays the port speed.

Duplex Mode Displays the duplex mode of the port.

Flow Control Displays if the Flow Control is enabled.

7 VLAN Configuration
The router supports 802.1Q VLAN, which can divide a LAN into multiple logical LANs.
Each logical LAN is a VLAN. Hosts in the same VLAN can communicate with each other.
However, hosts in different VLANs cannot communicate directly. Therefore, broadcast
packets can be limited to within the VLAN.

7.1 Creating a VLAN

Choose the menu Network > VLAN > VLAN to load the following page.
Figure 7-1 Creating a VLAN

Create a VLAN and add the port(s) to the VLAN, then click OK.

VLAN ID Enter a VLAN ID. The value ranges from 1 to 4094.

Name Specify the name of the VLAN for easy identification.

Ports Check the box to select the port and specify the port type in the specified VLAN. The
port can be divided into two types: TAG or UNTAG.

TAG: The egress rule of the packets transmitted by the port is Tagged.

UNTAG: The egress rule of the packets transmitted by the port is Untagged.

Description Optional. Enter a brief description for easy management and searching.
 Viewing the VLANs
Choose the menu Network > VLAN > VLAN to load the following page.
Figure 7-2 Viewing the VLAN

In the VLAN list you can view all the VLANs existing in the router.

VLAN ID Displays the VLAN ID.

Name Displays the VLAN name.

Ports Displays the ports which belongs to the corresponding VLAN.

Description Displays the description of the VLAN.

Note:
The VLAN list contains all the VLANs existing in the router. Some of them are manually created by
the user, and can be edited or deleted. Some are automatically created and referenced by the router
for some special scenarios like IPTV or management VLAN, and you cannot edit or delete these
VLANs.

7.2 Configuring the PVID of a Port

Choose the menu Network > VLAN > Port to load the following page.
Figure 7-3 Configuring the PVID

Configure the PVID of the port, then click Save.

Port Displays the port.

PVID Specify the PVID for the port. PVID indicates the default VLAN for the corresponding
port.

VLAN Displays the VLAN(s) the port belongs to.

8 IPv6 Configuration
To complete IPv6 configuration, follow these steps:
1) Configure the LAN to specify the type of assigning IPv6 address to the client.
2) Configure the WAN connection.

8.1 Configuring the LAN

Configure the type of assigning IPv6 address to the LAN clients.

Choose the menu Network > IPv6 > LAN to load the following page.
Figure 8-1 Configuring the LAN

1) In Global section, enable IPv6 function and click Save.

IPv6 Check the box to enable IPv6 function for the LAN.

2) In LAN section, configure the Assigned Type and Address prefix, then click Save.
 Assigned Type Select the appropriate type of assigning the IPv6 address according to your ISP.

DHCPv6: The DHCP server automatically assigns the IPv6 address and DNS
information to the clients.

SLAAC+Stateless DHCP: The DHCP server advertises the IPv6 prefix to the
client, the client then dynamically form a host identifier that is 64 bits long and will
be suffixed to the end of the advertised prefix to form an IPv6 address. Generally,
the host identifier was formed using the EUI-64. The DHCP server can also offer
the DNS information to the client when the client requests.

SLAAC+RDNSS: The DHCP server advertises the IPv6 prefix to the client, the
client then dynamically form a host identifier that is 64 bits long and will be
suffixed to the end of the advertised prefix to form an IPv6 address. Generally,
the host identifier was formed using the EUI-64. The DHCP server will also
automatically advertise the DNS information to the client.

Address Prefix Enter the LAN address prefix provided by your ISP.

Note: If the “Prefix Delegation” in WAN configuration is enabled, the LAN prefix will
be automatically assigned by the ISP, and you do not need to manually configure
it here.

Release Time The duration time in seconds when the assigned IPv6 address remains valid when
you choose the Assigned Type as DHCPv6. The default value is 86400 seconds .

Address Displays the IPv6 address of the LAN port.

8.2 Configuring the WAN

You can configure at most four WAN ports. Each WAN port can have its own IPv6 WAN
connection, providing link backup and expanding the bandwidth.

To complete WAN configuration, follow these steps:

1) Configure the number of WAN ports.
2) Configure the WAN connection.

8.2.1 Configuring the Number of WAN Ports

Choose the menu Network > WAN > WAN Mode to load the following page.
Figure 8-1 Configuring the WAN Mode
 WAN Mode Specify the number of WAN ports.

1: Configure physical interface 1 as WAN1.

2: Configure physical interface 1 and interface 2 as WAN1 and WAN2 respectively.

3: Configure physical interface 1, interface 2 and interface3 as WAN1, WAN2 and

WAN3 respectively.

4: Configure physical interface 1, interface 2, interface 3 and interface 4 as WAN1,

WAN2, WAN3 and WAN4 respectively.

Note:
• When a WAN port is added, the port-related entries are automatically added; when a WAN port
is deleted, the port-related entries are automatically deleted.

• The router will reboot after switching the WAN mode.

8.2.2 Configuring the WAN Connection

The router supports five IPv6 connection types: Static IP, Dynamic IP (SLAAC/DHCPv6),
PPPoE, 6to4 Tunnel and Pass-Through (Bridge), you can choose one according to the
information provided by your ISP.

Static IP: Select this if your ISP provides you with a fixed IPv6 address, default gateway and
DNS address.

Dynamic IP (SLAAC/DHCPv6): Select this if your ISP automatically assigns the IPv6
address and the corresponding parameters.

PPPoE: Select this if your ISP provides you with a PPPoE account.

6to4 Tunnel: Select this if your ISP uses 6to4 deployment for assigning address.

Pass-Through (Bridge): Select this if your ISP uses Pass-Through (Bridge) network
deployment. No parameters are required for this type of connection.
Choose the menu Network > IPv6 > WAN to load the following page.

 Configuring the Dynamic IP (SLAAC/DHCPv6)

Figure 8-2 Configuring the Dynamic IP (SLAAC/DHCPv6)

Follow these steps to configure Dynamic IP connection:

1) In the General section, check the box to enable IPv6 function, then click Save.

IPv6 Check the box to enable IPv6 function.

2) In the Internet section, choose the Internet Connection type as Dynamic IP (SLAAC/
DHCPv6), and configure the corresponding parameters. Then click Save.

Internet Choose Dynamic IP (SLAAC/DHCPv6) as the connection type.

Connection Type

IPv6 Address/ Displays the IPv6 address/Primary DNS/Secondary DNS of the WAN port. These
Primary DNS/ parameters are automatically assigned by the DHCPv6 server from your ISP.
Secondary DNS

Renew Click this button to get new IPv6 parameters assigned by the DHCPv6 server
from the ISP.

Release Click this button to release the IPv6 parameters assigned by DHCPv6 server
from the ISP.
3) In the Internet section, click Advanced to configure the way of getting the IPv6 address
and DNS address, and configure the Prefix Delegation. Then click Save.

Get IPv6 Address Choose the method by which the IPv6 address is obtained from the ISP.

DHCPv6: The DHCP server automatically assigns the IPv6 address.

SLAAC+Stateless DHCP: The DHCP server advertises the IPv6 prefix to the
WAN port, the WAN port then dynamically form a host identifier that is 64 bits
long and will be suffixed to the end of the advertised prefix to form an IPv6
address. Generally, the host identifier was formed using the EUI-64.

Prefix Delegation Enable or disable prefix delegation. The prefix will be assigned to the LAN clients.

Enable: The prefix of the IPv6 address will automatically be assigned by the ISP,
and you do not need to configure the prefix in LAN page.

Disable: You need to enter a prefix manually.

Note: If more than one WAN port is enabled with Prefix Delegation, the LAN port
will assign the prefix of the latest enabled WAN port to the LAN clients.

DNS Address Choose the way of getting DNS address from the ISP.

Get dynamically from ISP: The DNS address will automatically assigned by the
ISP.

Use the following DNS address: The user need to manually enter the DNS
address provided by the ISP.

Primary DNS/ Enter the DNS address provided by the ISP.

Secondary DNS

 Configuring the Static IP

Figure 8-3 Configuring the Static IP

Follow these steps to configure static IP connection:
1) In the General section, check the box to enable IPv6 function, then click Save.

IPv6 Check the box to enable IPv6 function.

2) In the Internet section, choose the Internet Connection type as Static IP, and configure
the corresponding parameters. Then click Save.

Internet Choose Static IP as the connection type.

Connection Type

IPv6 Address Enter the IPv6 address provided by your ISP.

Default Gateway Enter the default gateway provided by your ISP.

Primary DNS/ Enter the DNS address provided by your ISP.

Secondary DNS
 Configuring the PPPoE

Figure 8-4 Configuring the PPPoE

Follow these steps to configure PPPoE connection:

1) In the General section, check the box to enable IPv6 function, then click Save.

IPv6 Check the box to enable IPv6 function.

2) In the Internet section, choose the Internet Connection type as PPPoE, and configure
the corresponding parameters. Then click Save.
 Internet Choose PPPoE as the connection type.
Connection Type
Note: If your ISP provides only one PPPoE account for both IPv4 and IPv6
connections, and you have already established an IPv4 connection on this WAN
port, you can check PPPoE same session with IPv4 connection, then the WAN
port will use the PPP session of IPv4 PPPoE connection to get the IPv6 address.
In this case, you do not need to enter the username and password of the PPPoE
account on this page.
If your ISP provides two separate PPPoE accounts for the IPv4 and IPv6
connections, or the IPv4 connection of this WAN port is not based on PPPoE,
please don’t check PPPoE same session with IPv4 connection and manually
enter the username and password for the IPv6 connection.

Username Enter the PPPoE username provided by your ISP.

Password Enter the PPPoE password provided by your ISP.

IPv6 Address Displays the IPv6 address of the WAN port.

3) In the Internet section, click Advanced to configure the way of getting the IPv6 address
and DNS address, and configure the Prefix Delegation. Then click Save.

Get IPv6 Address Choose the method by which the IPv6 address is obtained from the ISP.

DHCPv6: The DHCP server automatically assigns the IPv6 address.

SLAAC+Stateless DHCP: The DHCP server advertises the IPv6 prefix to the
WAN port, the WAN port then dynamically forms a host identifier that is 64
bits long and will be suffixed to the end of the advertised prefix to form an IPv6
address. Generally, the host identifier is formed using the EUI-64.

Prefix Delegation Enable or disable prefix delegation. The prefix will be assigned to the LAN clients.

Enable: The prefix of the IPv6 address will automatically be assigned by the ISP,
and you do not need to configure the prefix in the LAN page.

Disable: You need to enter a prefix manually.

Note: If more than one WAN port is enabled with Prefix Delegation, the LAN port
will assign the prefix of the latest enabled WAN port to the LAN clients.

DNS Address Choose the way of getting DNS address from the ISP.

Get dynamically from ISP: The DNS address will automatically assigned by the
ISP.

Use the following DNS address: The user needs to manually enter the DNS
address provided by the ISP.

Primary DNS/ Enter the DNS address provided by the ISP.

Secondary DNS

 Configuring the 6to4 Tunnel

6to4 is an internet transition mechanism for migrating from IPv4 to IPv6, a system that
allows IPv6 packets to be transmitted over an IPv4 network. The IPv6 packet will be
encapsulated in the IPv4 packet and transmitted to the IPv6 destination through IPv4
network.
Figure 8-5 Configuring the 6to4 Tunnel

Follow these steps to configure 6to4 Tunnel connection:

1) In the General section, check the box to enable IPv6 function, then click Save.

IPv6 Check the box to enable IPv6 function.

2) In the Internet section, choose the Internet Connection type as 6to4 Tunnel, and
configure the corresponding parameters. Then click Save.

Internet Choose the connection type as PPPoE.

Connection Type

IPv4 Address/ These parameters will be dynamically generated by the IPv4 information of WAN
IPv4 Subnet port after you click Connect.
Mask/IPv4
Default Gateway

Tunnel Address Displays the tunnel address of the WAN port.

3) (Optional) In Internet section, click Advanced to configure the DNS server. Then click
Save.
 Use the following Check the box to manually enter the IP address DNS server provided by your
DNS Server ISP.

Note: If this option is not enabled, the router will use the default DNS servers with
the IPv6 address as 2001:4860:4860::8888 and 2001:4860:4860::8844.

Primary DNS/ Enter the IPv6 address of the DNS server provided by your ISP.
Secondary DNS

 Configuring the Pass-Through (Bridge)

In Pass-Through (Bridge) mode, the router works as a transparent bridge. The IPv6 packets
received from the WAN port will be transparently forwarded to the LAN port and vice versa.
No extra parameter is required.
Figure 8-6 Configuring the Pass-Through (Bridge)

Follow these steps to configure Pass-Through (Bridge) connection:

1) In the General section, check the box to enable IPv6 function, then click Save.

IPv6 Check the box to enable IPv6 function.

2) In the Internet section, choose the Internet Connection type as Pass-Through (Bridge),
then click Save.

Internet Choose the connection type as Pass-Through (Bridge).

Connection Type

Note:
If the Internet Connection Type of any WAN port is Pass-Through (Bridge), the IPv6 parameters of
the LAN port and the other WAN ports cannot be configured.