Transient Groundwater Analysis with Slope Stability 19-1

Transient Groundwater Analysis with

Slope Stability
This tutorial describes how to use Slide to calculate factors of safety for a
dam subjected to time-dependent changes in pore pressure. As part of the
tutorial, a transient groundwater analysis is performed using finite
elements.

The finished product of this tutorial can be found in the Tutorial 19

Transient + Slope Stability.slim data file. All tutorial files installed
with Slide 6.0 can be accessed by selecting File > Recent Folders >
Tutorials Folder from the Slide main menu.

Topics Covered

• Transient groundwater seepage analysis

• Slope stability with transient groundwater

Geometry

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-2

Model

Start the Slide Model program.

Project Settings
Open the Project Settings dialog from the Analysis menu. Set the
Stress Units to Metric, set the Time Units to Days and the Permeability
Units to meters/second. Set the Failure Direction to Left to Right as
shown.

Click on the Groundwater link on the left side. For the Method choose
Steady State FEA. Select the Advanced checkbox and choose Transient
Groundwater.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-3

The Method refers to the method used to obtain the initial state for the
transient groundwater analysis. In this tutorial we will perform a steady
state finite element analysis to get the initial state.

Now click on the Transient link on the left. Here we need to specify the
times at which we wish to observe pore pressure results. Change the
Number of Stages to 5. Enter the times for each stage as shown. Also
select the Calculate SF (Safety Factor) checkbox for each stage.

This will set up the model to calculate factor of safety at each specified
time as groundwater conditions are changing.

Click OK to close the Project Settings dialog.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-4

Slope Stability

You will now see a blank screen with three tabs at the bottom. One for
Slope Stability, one for Steady State Groundwater and one for Transient
Groundwater. The first part of this tutorial involves setting up the model
geometry. This can only be done in the Slope Stability mode, so click on
the tab for Slope Stability.

Boundaries
The model represents a dam overlying a strong foundation holding back
ponded water on one side. Here we will define the geometry of the
problem.

Make sure that you are in ‘Slope Stability’ view. Select the Add
External Boundary option in the Boundaries menu and enter the
following coordinates:

0,0

100 , 0

100 , 10

75 , 10

55, 20

51 , 22

44 , 22

20 , 10

0 , 10

c (to close the boundary)

Hit Enter to finish entering points. The model will look like this:

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-5

Now we need to define the boundary between the dam material and the
foundation. Select Boundaries → Add Material Boundary. Click on
the point at (0, 10) and then on the point at (100,10). Hit Enter to stop
entering points. The model will look like this.

Materials
Select Define Materials from the Properties menu. Change the name
of Material 1 to Dam. Set the Cohesion to 6 kN/m2 and φb to 35° as shown.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-6

When in Slope Stability mode, only the slope stability parameters can be
set. We will set the groundwater flow parameters later.

Click on the link for Material 2. Change the name to Foundation. Set the
Cohesion to 15 kN/m2 and set φ and φb to 30 degrees as shown.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-7

Click OK to close the dialog.

Assigning Properties
By default, the entire model is assigned Material 1 (Dam). To set the
foundation material, choose Properties → Assign Properties. Choose
Foundation and click inside the bottom part of the model. Close the
Assign Material dialog and the model should look like this.

You could also simply right click inside the foundation area and choose
Assign Material → Foundation.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-8

Slip Surfaces
In this tutorial, we wish to restrict the search for slip surfaces to include
only major failure surfaces extending from the top of the dam to the
bottom. To do this, we need to add another set of Slope Limits.

Go to Surfaces → Slope Limits → Define Limits. Click the box for

Second set of limits as shown.

It is possible here to specify coordinates of the limits but it is easier to do

this graphically by dragging them along the slope surface, so click on OK
to close the dialog. You will now see two sets of slope limits on the model.

We want potential slip surfaces to start from the top of the dam. So right
click on the slope limit icon at x=33 (second from the left) and select
Move Limits. Now drag the icon to the right side of the flat top of the
dam as shown.

Now drag the left icon at x=0 to the top left of the dam.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-9

Finally, drag the icon that is halfway down the slope at x=66 to the
bottom of the slope. Hit Enter to finish moving the limits and the model
should look like this:

Now that the slope limits are defined, we need to specify how Slide
should search for potential failure surfaces. Go to Surfaces → Surface
Options. Under Search Method, choose Auto Refine Search. This option
means that we do not have to define a search grid.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-10

Click OK to close the dialog.

Groundwater

Now it is time to set up the finite element model for calculation of

groundwater behaviour. First we will set up the initial state that exists
prior to the drawdown, so select the tab for Steady State Groundwater
at the bottom of the screen.

Mesh
Before we can set up the boundary conditions we need to create a finite
element mesh. This is easily done by selecting Mesh → Discretize and
Mesh. The model should now look like this:

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-11

Boundary Conditions
We will set up boundary conditions to simulate ponded water on the right
side.

Select Mesh → Set Boundary Conditions. For BC Type choose Total

Head and set the Total Head Value to 20 m. Uncheck the box for ‘Apply
to steady state AND transient analysis’.

Click on the right side of the slope near the bottom, and the top of the
foundation layer to the right of the dam. Click Apply. Click Close to close
the dialog. The model should look like this:

Transient Boundary Conditions

The ponded water model shown above represents the initial state. We
will now implement transient boundary conditions to simulate a gradual
drawdown of the water level.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-12

Click on the tab for Transient Groundwater at the bottom of the

screen. Select Mesh → Set Transient Boundary Conditions. Here we
set up a function that will change the boundary conditions with time.
Click the New button. Change the name to ‘Gradual Drawdown’ and set
the Type to ‘Total Head with Time’. Now fill in the Time and Total Head
values as shown:

Click OK. Now click on the bottom right part of the slope and the top of
the foundation layer as before. Click Apply. The model should look like
this:

Click Close to close the dialog. The plot now shows the height of the
ponded water at the last stage of the analysis.

Material Properties (Groundwater)

Select Properties → Define Hydraulic Properties. The hydraulic
properties required for a transient analysis are the same as those for a
steady state analysis except that water content (WC) must now be
specified.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-13

Click on the link for Dam material. For the Model, choose Simple. This is
a simple built-in function that relates permeability and water content to
matric suction. To view the relationships, click on the graph icon to the
right. Set the permeability Ks to be 1e-5 m/s. Leave the water content
WC as the default value of 0.4. The dialog should appear as shown.

Click on the link for the Foundation material. Set Ks to 1e-8 m/s.

Click OK to close the dialog.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-14

Compute
Save the model using the Save As option in the File menu. You could
now choose Compute (groundwater) from the Analysis menu to perform
the groundwater analysis. However, in this tutorial we want both the
groundwater and slope stability results to be computed. So select the tab
at the bottom for Slope Stability. Now select Analysis → Compute.
This will compute both the groundwater results and the slope stability
results. It may take a few minutes to perform the calculations. When it is
finished, choose Interpret (groundwater) from the Analysis menu to
view the results.

Interpret
You will now see the pressure head for the initial state. To show the
factor of safety as well, click the button on the toolbar for ‘Slope Stability
and Groundwater’.

You can see that the slope is quite stable at this time.

Click through the other stages using the tabs at the bottom. You will see
how the pressure head changes as the water table is lowered. After 6
days, the ponded water has reached its final depth (4 m above the
foundation) but the pressure head in the dam continues to change as
water flows from regions of high pressure to low pressure.

Click on the tab for Stage 5 (50 days). This essentially represents the
steady state. You can show the progression of the water table with time
by going to View → Display Options. Select the Groundwater tab and
under FEA water, select All Stages as shown.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-15

Click Done. The water tables at the different stages are now plotted as
dashed pink lines. They are difficult to see on this plot so change the plot
to show contours of Total Head using the drop down menu at the top. The
plot will now look like this:

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-16

You can see that the solid pink line represents the water table at 50 days
and the dashed pink lines represent the water table at other stages. Go
back to the Display Options and turn off the water tables. Change the
contours back to Pressure Head.

You can also see the changing factor of safety as the pore pressures
change. When the water table is lowered, the factor of safety decreases
dramatically since the weight of the water has been removed but the
excess pore pressures have not yet dissipated. At 6 days, the factor of
safety is just above 1, indicating that the slope will likely fail.

At 50 days, most of the excess pore pressures have dissipated and the
dam becomes more stable.

You can plot the factor of safety versus time by going to Data → Graph
SF with Time. You can choose which method results to plot. Choose both
the Bishop method and the Janbu method as shown.

Slide v.6.0 Tutorial Manual

 Transient Groundwater Analysis with Slope Stability 19-17

Click Plot to see the graph. It should look like this:

Here you can clearly see the rapid decrease in factor of safety as the
water table is lowered and the gradual increase as the excess pore
pressures dissipate. This example shows the importance of a transient
groundwater analysis, since a steady state analysis would suggest that
the dam is stable.

This concludes the tutorial.

Additional Exercise

At 50 days, the dam has not yet reached a steady state solution. Try
adding another stage (at say 100 days) to see the final steady state factor
of safety.

Slide v.6.0 Tutorial Manual