Meet with mega satisfaction

承认书
SPECIFICATION FOR APPROVAL

Part No. MLT666T

Description: LCD Power Supply Specification
Revision: 1.2
Customer.
Customer Approval No. :

承认鉴章后请寄回承认书正本一份
Please return to us one original of “SPECIFICATION FOR APPROVAL” with your approved signatures.

承认书 APPROVED SIGNATURES

核准人 APPROVED BY： 日期 DATE：

盖章鉴署 CHOP & SIGNATURES:

深圳市麦格米特电气技术有限公司
SHENZHEN MEGMEET ELECTRICAL TECHNOLOGY CO.,LTD
Add: 6F Tower 2, Zhongjian Industrial Building
18 Yanshan Road , Shekou, Shenzhen, P.R.China
ZIP CODE:518067
TEL: (0755)26693042 26693442
FAX: (0755)26693047
E-mail: www.megmeet.com

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
1 OF 11
Spec. Rev: Sampl Rev. Date Description Safety by Mechanica by Electrical by

1.0 1.0 2008/07/16 First issue shenchuchun ranhongjiang guichengcai

1.1 1.1 2008/10/06 Revise:1.2 shenchuchun ranhongjiang guichengcai

1.2 1.2 2008/11/06 Revise:1.2.1,fig8.1 shenchuchun ranhongjiang guichengcai

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
2 OF 11
 Section 目录
1. Power supply overview 电源性能指标
1.1 Input Electrical Characteristics Overview（输入特性）
1.2 Output Electrical Characteristics Overview（输出特性）
1.2.1 Output Voltage ,Current & Regulation.（输出电压电流调整率）
1.2.2 DC Output Ripple & Noise. （输出纹波和噪声）
1.2.3 Output Transient Response. （输出动态响应）
1.2.4 DC Output Hold-Up Time. （输出保持时间）
1.2.4 DC Output Overshoot At Turn On & Turn Off.（输出超调）
1.2.6 DC output voltage rise time（输出上升时间）
1.3 Remote On/Off Control： （遥控功能）
1.4 Protection: （保护功能）
1.4.1 DC output Over Voltage Protection. （输出过压保护）
1.4.2 DC Output Over current Protection. （输出过流保护）
1.4.3 DC Output Short Circuit Protection. （输出短路保护）
1.4.4 Reset After Shutdown.（保护功能复位）
2. Isolation 绝缘性能

3. Safety 安全规格

4. EMC 电磁兼容性
4.1 EMI （电磁干扰）
4.2 EMS （电磁抗扰）

5. Environmental Requirement 环境
5.1 Temperature （环境温度）
5.2 Humidity （环境湿度）
5.3 Altitude （海拔高度）
5.4 Cooling Method （冷却方式）
5.5 Vibration （振动耐受）
5.6 Impact （冲击耐受）

6. Dimension （物理尺寸）

7. Weight （重量）

8. Pin Connection (连接器脚位定义)

9. Power Supply mounting （安装尺寸）

10. Package (包装)

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
3 OF 11
 1. Power Supply Overview 电性能指标:

1.1 Table 1 Input Electrical Characteristics Overview（输入特性）

Input voltage range 输入电压 90Vac to 264Vac
Normal voltage range 标称输入 100Vac to 240Vac
Frequency range 频率范围 50Hz/60Hz±5%
Max input ac current 3.0Amax at full load condition
满载输入电流
Inrush current (cold start) 50Atyp peak, 120Vac; 100Atyp peak, 220Vac
浪涌电流
Efficiency(full load) 效率 80%min at 100Vac; 84%min at 220Vac
Harmonic current 谐波电流 Meet EN60065-2002/IEC61000-3-2 class D
Leakage Current 泄漏电流 Less Than 0.5mA, 230Vac input
Standby Power Loss 待机功耗 ≦1W 240Vac input ,Output current≤50mA,
Input Fuse 输入保险 T5A/250Vac

1.2 Output Electrical Characteristics Overview（输出特性）

1.2.1 Table 2 Output Voltage ,Current & Regulation.（输出调整率）

Output Voltage Regulation Min. current Load current range Peak current or power
输出电压 调整率 最小电流 带载电流范围 峰值电流或功率
+V1(+24V) +V1±5% 0.2 A 0.2A-5.0A ≤6.5A
+V2(+12V) +V2±10% 0.3 A 0.3A-2A
+5.0V +5.0V±5% 0.1 A 0.1A-3A ≤45W
+5.0V(STB) +5.0V±5% 0.05 A 0.05A-1A
Note:* The peak current or power should be test at other of dc output at Rated
load ,And the peak current pulse width within 100ms 峰值电流或功率的测试是在其它额定
负载时测试，且脉宽小于 100 毫秒。

1.2.2 Table 3 DC Output Ripple & Noise. （输出纹波和噪声）

Output Voltage Ripple & Noise (Max.)

+V1(+24V) 240mVp-p@25℃; 350mVp-p@-10℃
+V2(+12V) 120mVp-p@25℃; 200mVp-p@-10℃
+5.0V 50mVp-p@25℃; 200mVp-p@-10℃;
+5.0V(STB) 60mVp-p@25℃; 200mVp-p@-10℃; 150mVpp when STB
Note: 1) Measurements shall be made with an oscilloscope with 20MHz bandwidth.
示波器须设置在 20 兆赫兹带宽
2) Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a
10uF electrolytic capacitor to simulate system loading.
输出须并联 0.1uF 的陶瓷电容和 10uF 的电解电容来模拟负载

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
4 OF 11
 1.2.3 Output Transient Response. （输出动态响应）

Table 4. Test condition.测试条件

Voltage Tolerance Limit Slew Rate Load Change
5.0V/5.0VSB±5% 0.2A/uS Min. to 50% load and 50% to Max load
24V/12V/±10%
All output±10% 0.2A/uS Min. load to Max load
Note: Transient response measurements shall be made with a load changing repetition
rate of 50Hz to 10kHz. 以 50~10KHz 的频率跳变负载来测试。

1.2.4 Table 5 DC Output Hold-Up Time. （输出保持时间）

Output Voltage 120Vac input 220Vac input

+V1(+24V) ≥10 mS ≥10 mS
+V2(+12V) ≥10 mS ≥10 mS
+5.0V ≥10mS ≥10 mS
+5.0V(STB) ≥10 mS ≥10 mS
Note: All of dc output at full load. 所有输出带满载

1.2.5 Table 6 DC Output Overshoot At Turn On & Turn Off.（输出超调）

Output Channel Output(V) Over shoot voltage(V)超调电压
Turn on 开机 Turn off 关机
+V1(+24V) + 24V 10% 10%
+V2(+12V) + 12V 10% 10%
+5.0V +5.0V 10% 10%
+5.0V(STB) +5.0V 10% 10%
Note: All of dc output current from Min. to Max. 测试时负载范围：最小到最大

1.2.6 Table 7 DC output voltage rise time（输出上升时间）

Output Voltage 120Vac input &Full Load 220Vac input &Full Load

+V1(+24V) ≤100mS ≤100mS

+V2(+12V) ≤100 mS ≤100 mS
+5.0V ≤100mS ≤100mS
+5.0V(STB) ≤60 mS ≤50 mS
Note: The output voltages shall rise from10% to 90% of their output voltage.
输出从 10%上升到 90%的时间

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
5 OF 11
 1.3 Remote On/Off Control：（遥控功能）
The power supply DC outputs (without +5.0Vsb) shall be enable with an active-high
TTL(≥2.5V/2.0mA)-compatible signal(Ps-on). The +5.0Vsb is on whenever the AC
power is present.
除 5.0Vsb 外，其余输出受控于一个 TTL 电平兼容的信号（Ps-on≥1.5V/2.0mA）,
5.0Vsb 上电就存在。
* When Ps-on is pulled to TTL high, the DC outputs are to be enabled.
Ps-on 高电平，打开输出
* When Ps-on is pulled to TTL low or open circuit, the DC outputs are to be disabled.
Ps-on 低电平，关闭输出
Table 8.
Ps-on Signal Comments Outputs
Ps-on- high ≥1.5V&2.0mA ( source) Output
Ps-on- low ≤0.5V X
Ps-on-open -- X

1.4 Protection: （保护功能）

1.4.1 Table 9 DC output Over Voltage Protection. （输出过压保护）

Output Voltage TYP. Over Voltage Comments

+V1(+24V) 28V Hiccup 尝试重复启动

Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load.
应该在最大交流输入电压 264 伏和轻载、空载下测试。

1.4.2 Table 10 DC Output Over current Protection. （输出过流保护）

Output Voltage Over Current Comments

+V1(+24V) ≥6Atyp* Power supply latch into shutdown state
输出锁机
+V2(+12V) ≥2Atyp* Hiccup 尝试重复启动
+5V ≥3.5Atyp* Hiccup 尝试重复启动
+5.0VSTB ≥1.5Atyp* Hiccup 尝试重复启动

Note:* The over current protection should be test at other of dc output at Rated load
过流保护测试是在其它额定负载时测试.

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
6 OF 11
 1.4.3 Table 11 DC Output Short Circuit Protection. （输出短路保护）

Output Voltage Comments

+V1(+24V) Shutdown 关机
+V2(+12V) Hiccup 尝试重复启动
+5V Hiccup 尝试重复启动
+5.0V(STB) Hiccup 尝试重复启动
Note:* The Short Circuit protection should be test at other of dc output at Rated load
短路保护测试是在其它额定负载时测试.

1.4.4 Reset After Shutdown.（保护功能复位）

Recycle the ps-on signal, the power supply will restart after the fault removed.
故障去除后，关掉 Ps-on 信号再打开，电源即可恢复。

2. Isolation（绝缘性能）

2.1 Table 12 （绝缘阻抗）

Input To Output DC500V 50MΩmin (at room temperature)
Input To FG DC500V 50MΩmin (at room temperature)
Output To FG Non Isolated

2.2 Table 13 （绝缘耐压）

Input To Output 3000Vac 50Hz 1minute ≤10mA
Input To FG 1500Vac 50Hz 1minute ≤10mA
Output To FG Non Isolated
Note: Open FG and Output return. 交流地和输出负极要断开。

3. Safety （安全规格）
The power supply shall compliance with the following Criterion:
电源安全性满足下列标准
1) UL60950
2) EN60950

3) GB4943-1995

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
7 OF 11
 4. EMC （电磁兼容性）

4.1 EMI （电磁干扰）

The power supply shall compliance with the following Criterion:

电源电磁干扰满足下列规则：
1) Conduction Emission : （传导干扰度）
*EN55022, CLASS B
*GB9254, CLASS B
*FCC PART15 CLASS B
2) Radiated Emission : （辐射干扰度）
*EN55022, CLASS B
*GB9254, CLASS B
*FCC PART15 CLASS B
注：The power board should be assembled in customer's product to test for
passing the regulations 需配合用户电路整机通过上述规则。

4.2 EMS （电磁抗扰）

The power supply shall compliance with the following Criterion:

电源电磁抗扰满足下列规则：
1) ESD （静电抗扰度）
*GB17626.2-1998/IEC61000-4-2
2) EFT （脉冲群抗扰度）
*GB17626.4-1998/IEC61000-4-4 3KV
3) Surge （雷击浪涌）
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV

5. Environmental Requirement （工作环境）

5.1 Temperature （环境温度）
* Operating: 0℃ to +40℃.
* Store: -20℃ to +80℃.
5.2 Humidity （环境湿度）
* Operating: From 10%to90% relative humidity (non-condensing).
* Store: From 5 to 95% relative humidity (non-condensing).
5.3 Altitude （海拔高度）
* Operating: to 10,000 ft.
* Store: to 20,000ft.
5.4 Cooling Method （冷却方式）
* Ventilation cooling . 自然冷却
5.5 Vibration （振动耐受）
* 10-55Hz, 19.6m/s²(2G), 3minutes period, 60minutes each along X, Y and Z axis.
5.6 Impact （冲击耐受）

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
8 OF 11
 * 49m/s²(5G),11ms, once each X, Y and Z axis.

6. Dimension （物理尺寸）
* 192mm X 130mm X30mm (长 L *宽 W * 高 H ).

7. Weight （重量）
* 500g

8. Pin Connection (连接器脚位定义)

Table 15 Pin-CON5 Connection And Function
NO. Pin Connection Function

5.6.7.8 GND +24VDC RETURN

1.2.3.4 +V1 +24VDC OUTPUT
Note: CON103 -- XH CONNEETION, TYPE : pitch2.5mm

Table 16 Pin-CON3Connection And Function

NO. Pin Connection Function

3.4 GND +24VDC RETURN

1.2 Vaudio +24VDC OUTPUT
Note: CON103 -- XH CONNEETION, TYPE : pitch2.5mm
Table 17 Pin-CON4 Connection And Function
NO. Pin Connection Function

1. 2 GND +5V +5VSB +12VDC RETURN

3.4 +5V +5VDC OUTPUT
5 STB SMPS ON/OFF CONTROL(ON = HIGH)
6 +5VSB STANDBY(+5.0VDC) OUTPUT
7.8 +5V +5VDC OUTPUT
9.10.11 GND +5V +5VSB +12VDC RETURN
12.13 +12V +12VDC OUTPUT
Note: CON5 -- VH CONNEETION, TYPE : pitch2.5mm
Table 18 Pin-CON1 Connection And Function
NO. Pin Connection Function

① AC-L AC INPUT LINE

② NC NC
③ AC-N AC INPUT NUTURE
Note: CON1 -- VH CONNEETION, TYPE : pitch3.96mm

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
9 OF 11
 Fig.8.1 Pin Connection (Top View)
Top View

9. Power Supply Mounting （安装尺寸）

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
10 OF 11
 Mount Method( 装配注意事项 )
TOP
Table 19 H

D ≤5.5mm (1*) D
PCB
≥6.0mm
H ≤3.0mm (2*)
131.0mm
Note:
1*. Mount the unit to the mounting SPS UNIT
board using M3 screw. The maximum
value of the tightening torque is 0.4N-M.
The insertion depth of the screw should
be less 5.5mm.

2*. Add 136mmX196mmX 0.25mm (W*-

H*T )Mylar under PCB bottom.

BOTTOM
Nature wind
10. Package 包装
防静电气泡袋，
包装箱尺寸：

DESCRIPTION:
MEGMEET 麦格米特电气技术有限公司 (规格书)
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD. SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD Model No.:
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION. MLT666T
DATE PREPARED CHECKED APPROVED Document No.: REV:
2008/11/06 RANHONGJIANG GUICHENCAI ZHANGZHI MSPS-MLT666T-1.2 1.2
11 OF 11