Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology

ISSN No:-2456-2165

Seismic Analysis of Regular and Irregular Multistorey

Buildngs Using Staad.Pro
Nirmal Raj1, Nandini Devi2
P.G student, Department of Civil Engineering, Adhiyamaan college of Engineering, Hosur, Tamil Nadu, India1 .
Professor, Department of Civil Engineering, Adhiyamaan college of Engineering, Hosur, Tamil Nadu, India 2 .

Abstract:- Earthquake is a natural phenomenon which I. INTRODUCTION

involves shaking of ground and can be caused
anywhere. Once the ground shakes, a structure resting Buildings with simple and regular geometry will have
on it will experience motion at its base. Due to this very less damage and better seismic performance due to the
motion the structure may deform back and forth which uniform distribution of mass and stiffness throughout the
may cause lateral displacement and storey drift that can plan and elevation of the structure. In case of irregular
affect the structural behavior of the building. To structures, we cannot expect the same seismic behaviour
overcome this, structural engineers should design the and less deformation as obtained in regular structures
structure considering the seismic loads and improve the because the distribution of mass and stiffness will not be
seismic behavior of the building. However, design for uniform in irregular structure. Due to this non uniform
improving the seismic behavior for irregular structures distribution, it becomes quite challenging for the structural
will not be as simple as regular structures. Here comes designers to provide a design to the irregular structures for
the challenge for structural engineers and designers to a better seismic performance. In this modern world, we
get better seismic performance from irregular cannot avoid the irregular structures compromising all
structures as possible because the necessity for irregular structures to be designed regular. Although it is crucial to
structures have become a lot today. In this paper, improve the seismic response of irregular buildings, it
seismic performance of G+15 irregular buildings of re- becomes the ideal duty for designers to prevent blaming the
entrant corner irregularity, vertical geometric irregularities for a structural collapse and obtain the
irregularity and stiffness irregularity is modelled and appropriate remedy. Irregularities of various types namely
analyzed for its seismic behavior using the software re-entrant corner irregularity, vertical geometric irregularity
STAAD.Pro and compared with the seismic behavior of and stiffness irregularity as specified in Indian standards is
regular structure. Response spectrum analysis of figured below.
dynamic analysis method is used and from the analysis,
base shear, lateral displacement, time period and storey
drift are determined. Based on the determined
parameters, comparison is made among the
irregularities and also between the regular and
irregular structure. As a result, the seismic performance
of a regular structure is found to be good as expected
whereas the seismic performance of the irregularities
Fig.1:- Re-Entrant Corner Fig.2:- Stiffness
are not satisfactory enough. However when comparing
Irregularity Irregularity
the three considered irregularities with one another, the
stiffness irregularity is found much better than the
other two irregularities meanwhile the re-entrant
corner irregularity have shown the worst behavior
towards the seismic loads. The vertical geometric
irregularity is found intermediate. It is neither better as
stiffness irregularity nor worst as re-entrant corner
irregularity. In case of irregularity, it is always
suggested to prefer irregularities like stiffness
irregularity and avoid the worst re-entrant corner Fig.3:- Vertical Geometric
irregularity as much as possible since it gives a poor Irregularity.
seismic response and even it is possible to get a better
seismic performance, it earns an highly uneconomical II. LITERATURE REVIEW
design.
Prof. M.R.Wakchaure, Anantwad Shirish, Rohit
Keywords:- Seismic Analysis, Response Spectrum Analysis, Nikam, suggested that the purpose of study was to analyse
Base Shear, Lateral Displacement And Storey Drift plan irregularities on high-rise structures and to observe the
behaviour of structures. For this, ETABS a linear dynamic
analysis and design program for three dimensional
structures has been used. Dynamic analysis has been
carried out to know about deformations, natural

IJISRT19AP71 www.ijisrt.com 458

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
frequencies, time periods, floor responses and  Base Shear :
displacements. Dileshwar Rana et.al (2015), has shown the Base shear is an estimate of the maximum expected
performance & behavior of regular & vertical geometric lateral force on the base of a structure due to seismic
irregular RCC framed structure under seismic motion. Five activity. Whenever seismic activity (earthquake) occurs, the
types of building geometry are taken in this project: one base of the structure experiences a lateral force, whose
regular frame & four irregular frames. A comparative study maximum value is termed as base shear and its
is made between all these buildingconfigurations height mathematical value is given as product of net vertical force
wise and bay wise. All building frames are modeled & at the base and a factor called horizontal seismic coefficient
analyzed in software Staad.Pro V8i. The comparison of whose value depend upon factors like seismic zone etc.
results have been done. storey wise for each bay and then
bay wise for same building height. It is concluded that as  Lateral Displacement :
the amount of setback increases the shear force also Lateral displacement is defined as the absolute value
increases. The fluctuation of critical shear force from of displacement experienced in any storey of a structure
regular to vertical geometric irregular is very high(from under the action of lateral forces.
0KN to 80KN for 4 bay configurations) and (from 10KN to
120KN for 8 bay configurations). Suchita K. Hirde et.al  Time Period :
(2016), has made an attempt to study the building models A time period (denoted by T) is the time needed for
with plan irregularities. This paper presents the one complete cycle of oscillation or vibration to pass in a
performance of the symmetric and asymmetric buildings given point. As the frequency of a wave increases, the time
subjecting to seismic loads. The guidelines and the period of the wave decreases.
methodology of the Indian standard of practice IS 1893 The unit for time period is ‘seconds’.
(Part I): 2002 is used to analyse the structures. In retrofitted
building the hinges developed in beams are at Life safety IV. ANALYTICAL WORK
which is acceptable criteria for the building. After
retrofitting with X steel bracing it is observed that PARAMETERS DESCRIPTION
performance level of building is changed to life safety level
No. of stories G + 15
from Collapse level. The T shaped building retrofitted with
X-bracing has base shear of 6393.5KN whereas in the same Height of the building 51.2m
building (when not retrofitted) has the base shear of
Storey height 3.2
5936.1KN. The displacement is reduced from 624mm to
586mm in bracing retrofitted building. Plan dimension 20m x 20m
Beam dimension 0.45m x0.45m
III. RESPONSE SPECTRUM ANALYSIS
Slab thickness 150mm
This study is carried out to check the effect of the
Wall thickness 230mm
irregular building in G +15 storey in seismic zone 4. The
analysis is carried out with response spectrum analysis and Column dimension 0.60m x 0.60m
the results are obtained and tabulated in terms of storey
drift, base shear, time period and lateral displacement. Unit weight of concrete 25kN/m3
Unit weight of brick 20kN/m2
A. Response Spectrum Analysis : masonry
Response spectrum analysis permits the multiple SEISMIC DATA
modes of response of a building to be taken in to account. It
can be performed for all simple or complex structures. The Earthquake zone Zone 1V
response of a structure can be defined as a combination of Type of analysis Response spectrum analysis
many special shapes in a vibrating string corresponding to
the harmonics. It can be used to determine the modes of a Damping Ratio 5%
structure. For each mode, a response is read from the Soil type II (IS:1893-2002)
design spectrum, based on the modal frequency and the
modal mass and they are then combined to provide an Zone factor 0.24 (Cl.6.4.2 of IS:1893-
estimate of total response of the structure. Modal responses 2002)
are combined make use of square root of sum of squares Importance factor 1 (Table 6 of IS:1893-2002)
(SRSS), complete quadratic combination (CQC) and Response reduction factor 5 (Table 7 of IS:1893-2002)
absolute (ABS) strategies.
Table 1
 Storey Drift :
storey drift is the drift of one level of a multi storey
building relative to the level below. Interstorey drift is the
difference between the roof and floor displacements of any
given storey as the building sways during the earthquake
normalized by the storey height.

IJISRT19AP71 www.ijisrt.com 459

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
 Plan

3D View
 Plan

Fig.5:- Re-Entrant Corner Irregularity.

Fig.4:- Regular.

3D View
 Plan

3D view

Fig.6:- Vertical Geometric Irregularity

IJISRT19AP71 www.ijisrt.com 460

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
V. RESULTS AND DISCUSSION

 The base shear for regular structure is found to be 3027

KN. The storey drift, bending moment and
displacement obtained for a regular structure is 0.2mm,
162knm and 2.75mm respectively.
 For a re-entrant corner irregular structure, the base shear
is found to be 1913 KN. The storey drift, bending
moment and displacement obtained for a re-entrant
corner irregular structure is 0.9mm, 191knm and
12.75mm respectively.
 The base shear for vertical geometric irregular structure
is found to be 2700KN. The storey drift, bending
moment and displacement obtained for a vertical
geometric irregular structure is 0.6mm, 175knm and
3D view 6mm respectively.
 For a stiffness irregular structure is found to be 3200
 Plan KN. The storey drift, bending moment and
displacement obtained for a stiffness irregular structure
is 0.5mm, 171knm and 4mm respectively.

Fig.7:- Stiffness Irregularity

 Storey Drift :

STRUCTURE TYPES MAXIMUM STOREY DRIFT (MM)

REGULAR 0.2
RE-ENTRANT CORNER 0.9
VERTICAL GEOMETRIC IRREGULAR 0.6
STIFFNESS IRREGULAR 0.5
Table 2:- Maximum Storey Drift for Various Structure Types

 Base Shear :

STRUCTURE TYPE BASE SHEAR

(KN)
RE-ENTRANT CORNER 1913.25
VERTICAL GEOMETRIC IRREGULAR 2700
STIFFNESS IRREGULAR 2925
REGULAR 3027
Table 3:- Base Shear for Various Structure Types.

IJISRT19AP71 www.ijisrt.com 461

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
 Displacement :

STRUCTURE TYPES MAXIMUM DISPLACEMENT (MM)

REGULAR 2.75

RE-ENTRANT CORNER 12.5

VERTICAL GEOMETRIC IRREGULAR 6

STIFFNESS IRREGULAR 4

Table 4:- Maximum Displacement for Various Structure Types

 Bending Moment :

STRUCTURE TYPES MAXIMUM BENDING MOMENT (KNM)

REGULAR 162

RE-ENTRANT CORNER 191

VERTICAL GEOMETRIC IRREGULAR 175

STIFFNESS IRREGULAR 171

Table 5:- Maximum Bending Moment for Various Structure Types

 Time Period :

STRUCTURE TYPE TIME PERIOD

(SECONDS)
RE-ENTRANT CORNER 3.8
VERTICAL GEOMETRIC IRREGULAR 3.1
STIFFNESS IRREGULAR 6
REGULAR 4
Table 6:- Time Period for Various Structure Types.

 Base Shear :

Fig.10:- Comparison of Base Shear among Various Structure Types.

IJISRT19AP71 www.ijisrt.com 462

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
 Mode Period :

Fig.11:- Comparison of Mode Period among Various Structure Types.

 Displacement :

Fig.12:- Comparison of Maximum Displacement among Various Structure Types.

 Bending Moment :

Fig.13:- Comparison of Maximum Displacement among Various Structure Type

IJISRT19AP71 www.ijisrt.com 463

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165

 Storey Drift :

Fig.14:- Comparison of Maximum Storey Drift among Various Structure Types.

VI. CONCLUSIONS the structure, thereby leading to the reduction in

stiffness of the structure.
From the results obtained, it is clearly shown that the  Response spectrum method provides a clear
seismic response of regular building is highly good and interpretation of the contributions of different modes of
satisfactory when compared to the seismic response of all vibration. It is useful for the seismic evaluation of
the irregular structures (Re-entrant corner irregularity, structures.
Vertical geometric irregularity and Stiffness irregularity).  From the above conclusions it is clear that the regular
structure with RC moment resisting frame and with
 However when a comparison is made between the three masonry walls, perform better under the action of
irregularities considered, it can be concluded that the seismic load, compared to irregular structure.
seismic response of stiffness irregular structure is far  The irregular structures, especially the re-entrant corner
better than the vertical geometric irregular, and the re- structure shows the worst performance when subjected
entrant corner irregularity. to seismic excitation compared to other type of irregular
 Re-entrant corner irregularity shows the worst seismic structures compared to other irregular structures (mass
performance among the considered irregularities. irregular, mass irregular, vertical geometric irregular
 The base shear is found very high for stiffness irregular structures).However, stiffness irregular structure has the
structure compared to other irregular structures ( 62.7% better seismic performance when compared to the other
higher than re-entrant corner irregularity, 18.5% higher types of considered irregularities.
than vertical geometric irregular structure and 5.1%
higher than regular structure). REFERENCES
 The lateral displacement is found very high for re-
entrant corner structure compared to other irregular [1]. Prof. M.R.Wakchaure, Anantwad Shirish, Rohit
structures (52.1% higher than vertical geometric Nikam, “Study Of Plan Irregularity On High-Rise
irregular structure, 68% higher than stiffness irregular Structes”, International Journal of Innovative
structure and 78.4% higher than regular structure). This Research and Develpoiment” Vol: 1 ,Issue 8, October,
is due to change in geometry of the structure and the 2012, pp: 269-281.
inertial forces are more and hence displacement is more. [2]. Ravikumar C M, Babu Narayan K S, Sujith B, Venkat
 The bending moment is found to be maximum in re- Reddy, (2012) “Effect of Irregular Configurations on
entrant corner irregular structure. It is 8.4% higher than Seismic Vulnerability of RC Buildings”, Architecture
vertical geometric irregularity, 10.4% higher than Research, pp: 20-26.
stiffness irregularity and 15.2% higher than regular [3]. Poonam, Anil Kumar, and Ashok k.Gupta, “Study of
structure) response of structurally irregular building frames to
 The storey drift is very high for re-entrant corner seismic excitations”, International Journal of Civil,
structure compared to other irregular structures (33% Structural, Environmental and Infrastructure
higher than vertical geometric irregular, 44% greater Engineeringn Research and Development
than stiffness irregular structure and 77.2% higher than (IJCSEIERD), Vol.2, Issue 2 (2012), pp: 26-31.
regular structure). This is due to change in geometry of [4]. Nonika. N, Gargi Danda De “Comparative Studies on
Seismic Analysis of Regular and Vertical Irregular

IJISRT19AP71 www.ijisrt.com 464

Volume 4, Issue 4, April – 2019 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
Multistoried Building”, International Journal for Journal of Science Technology & Engineering ,
Research in Applied Science & Engineering Volume 3, Issue 09, March 2017, pp: 438-439.
Technology (IJRASET), Volume 3 Issue VII, July [16]. Kusuma B, “Seismic Analysis of a High-rise RC
2015, pp: 396-407. Framed Structure with Irregularities”, International
[5]. Manoj Kumar, Hemant Singh Parihar, Rahul Research Journal of Engineering and Technology
Satbhaiya, “Comparative study of seismic (IRJET)”, Volume: 04, Issue: 07, July -2017, pp:
performance of building having Stiffness vertical 1338-1342.
irregularity at different floor levels”, International [17]. Imranullahkhan, Shri Satya Eswar Sanyasi Rao,
Research Journal of Engineering and Technology “Seismic Analysis of Irregular L-Shape Building in
(IRJET), Volume: 02, Issue: 09, Dec-2015,pp: 1936- Various Zones”, International Journal of Innovative
1942. Research in Science, Engineering and Technology,
[6]. Dileshwar Rana1, Prof. Juned Raheem2, “Seismic Vol. 6, Issue 8, August 2017, pp: 16529-16536.
Analysis of Regular &Vertical Geometric Irregular [18]. Anju Nayas, Minu Antony, “Pushover analysis of plan
RCC Framed Building”, International Research irregular RC buildings with special columns”,
Journal of Engineering and Technology (IRJET), International Journal of Engineering Research and
Volume: 02, Issue: 04 , July-2015, pp: 1396-1401. Technology(IJERT), Vol.6, Issue-5, May 2017, pp:
[7]. Arvindreddy, R.J.Fernandes, “Seismic analysis of RC 95-99.
regular and irregular frame structures”, International [19]. Akhil R1, Aswathy S Kumar2 , “seismic analysis of
Research Journal of Engineering and Technology regular and irregular buildings with vertical
(IRJET) , Volume: 02, Issue: 05, Aug-2015, pp: 44- irregularity using staad.pro” International Research
47. Journal of Engineering and Technology (IRJET),
[8]. Suchita K. Hirde and Rahul A. Aher, “Seismic Volume: 04,Issue: 06, June -2017, pp: 1863-1866.
Evaluation of Irregular Structures”, International [20]. Ilham Salehi, Dr. Raman Nateriya ,“Seismic
Journal of Current Engineering and Technology, Evaluation of Vertical Irregular Building with
Vol.6, No.5 (Oct 2016) , pp: 1665-1672. Setback”, International Research Journal of
[9]. Shivkumar Hallale, H Sharada Bai “Seismic Behavior Engineering and Technology (IRJET), Volume: 05
of Buildings with Plan Irregularity with and Without Issue: 06, June-2018. pp: 561-564.
Structural Infill Action”, International Journal of [21]. Ann Vincent, Mariamol Kuriakose, “Estimation of
Recent Advances in Engineering & Technology seismic performance of irregular structures using
(IJRAET) , Volume-4, Issue -4, 2016, pp: 97-101. response spectrum method” International Research
[10]. Girum Mindaye, Dr. Shaik Yajdani, “Seismic Journal of Engineering and Technology
Analysis of a Multistorey RC Frame Building in (IRJET),Volume: 05, Issue: 04, Apr-2018, pp: 4169-
Different Seismic Zones”, International Journal of 4175.__
Innovative Research in Science, Engineering and
Technology, Vol. 5, Issue 9, September 2016, pp:
17209-17221.
[11]. Gauri G. Kakpure & Ashok R. Mundhada, (2016)
“Comparative Study of Static and Dynamic Seismic
Analysis of Multistoried RCC Building by ETAB: A
Review”, International Journal of Emerging Research
in Management &Technology (Volume-5, Issue-12),
pp:16-20.
[12]. J. P. Annie Sweetlin, R. Saranraj & P. Vijayakumar,
“Comparison of Displacement for Regular and
Irregular Building Due To Seismic Forces”, Imperial
Journal of Interdisciplinary Research(IJIR), Vol:2,
Issue-6,2016, pp: 1156-1161.
[13]. Pradeep Pujar, Amaresh, “Seismic analysis of plan
irregular multistoried building with and without shear
walls”, International Research Journal of Engineering
and Technology (IRJET), Volume: 04 Issue: 08, Aug -
2017, pp:1405-1411.
[14]. Piyush Mandloi, Prof. Rajesh Chaturvedi, “Seismic
Analysis of Vertical Irregular Building with Time
History Analysis” IOSR Journal of Mechanical and
Civil Engineering (IOSR-JMCE), Volume 14, Issue 4
Ver. III (Jul. – Aug. 2017), pp:11-18.
[15]. Neha M. Parab, Prof. Vijaykumar P. Bhusare ,
“Review Analysis on Seismic Performance of
Torsional Irregular RC Structures”, International

IJISRT19AP71 www.ijisrt.com 465