Plastics Testing Machines & Ancillary Equipments

Your Quality Our Commitment

An ISO 9001-2008 Company

 Content
• Company Profile 1 • Milling Contour Cutter Machine (CNC Based) 28
• Range of Testing Equipments 2 with PC Interface Facility
• Contour Cutter Machine (Template Type Cutting)
• Universal Testing Machines with 3 to 8
Different Capacities & Applications • Falling Dart Impact Tester for HDPE / PVC / PPR / Fabric 29
• Pull-out Test Application of Column Pipes (For ½” to 6” Pipe Dia) • U.V. Weather Meter (Accelerated Weathering Tester)
• Different Types of Grips / Jaws • Thermo Cyclic Test Equipment 30
• Different Types of Die Cutting Punches (For C-PVC Pipes & Fittings Test Application)
• Hydraulic Cylinder Operated / Manual Press for Die Punches • Equipments for Electrical Conduit Pipes/Casings 31 & 32
• Additional Various Attachments with UTM Testing Application
• Izod – Charpy Impact / Tensile Pendulum Impact Tester 9 • Bending Test
Notch Cutter • Compression Test
• Falling Dart Impact Tester for 10 • Collapse Test
Films /Thin Sheets / Geomembrane • Impact Test
• Elmendorf Tear Tester • Piston Gauges for ID Measurement
• “C” Type Gauges for OD Measurement
• Co-efficient of Friction Tester 11
• Ring Gauges for OD Measurement
• Opacity Tester For Film & PVC Pipe Testing Applications
• Million Meg OHM Meter
• Shrink Oil Bath Apparatus 12 • H.V. Test Apparatus
• GSM Cutter With Rubber Pad
• Hydraulic Press for Cone Type End Plugs Clamping 33
• Electronic Weighing Balance with Density Kit (0.1 mg Accuracy)
• Sieve Analysis Tester
• Cone Tester
• Moisture Analyzer
• Manometer Pressure Test Machine
• Creep Resistance Tester 34
• Environmental Stress Cracking Resistance Test Apparatus 13
Deepak Asrani • Emitter Flow Rate Variation Tester as per IS : 13487
• Melt Flow Rate Index Tester
Chief Innovator • Equipments for Inline Emitting Pipe Testing as per IS : 13488 35
• Carbon Black Content Tester 14
• Testing Apparatus for Resistance to Pullout of Joints
• Carbon Black Dispersion Tester
Be in control of your larger business • Emitting Pipe Flow Rate Measurement Tester
• Hot Air Circulating Oven 15 • Testing Apparatus for Resistance to Tension at Elevated Temperature
destiny, by being in control of even • Muffle Furnace for Ash Content Test Application • Go Not Go Gauges
the most minuscule part of your
• Methylene Chloride Tester 16 • Traveling Microscope
quality control process and product • Bulk Density / Dry Flow / Flowability / Pourability Test Apparatus • External Co-efficient of Friction Tester 36
quality. May quality facilitate your
• Hydrostatic Pressure Testing Machine 17 to 19 • Torsion Tester
success. • Abrasion Resistance Tester
• Room / Hot / Cold Water Bath / Temp. Malfunctioning Bath 19 & 20
• Deep Freezing Chamber for Specimen Conditioning Application 21 • Torque Rheometer & Mixers with Single 37 & 38
Screw Extrusion Attachments
• Humidity Chamber Unit for Specimen Conditioning Application 22
• Reversion Oil Bath • Test Equipment for Apparent Initial Circumferential 39
Tensile Strength Test Application (For GRP Pipes/Composites)
• End Plugs for Different Applications 23
• Test Station for GRP Couplers With Hydraulic Clamping
• HDT / VSP Tester (Heat Deflection Temperature / 24
• DRS 50 Ring Stiffness Tester 40

solutions for quality control VICAT Softening Temperature)

• 20 Ton Compression Moulding Press (Lab Model)
• 50 Ton Microprocessor Based Compression
25
• UTM DTRX 250 KN
• ISO 9001 : 2008 Quality Certification 41

and evaluations Moulding Press (Lab Model)

• Two Roll Mill (Lab Model)
• Differential Thermal Analyzer (OIT Tester)
26
27
• Motorised “V” Notch Cutter
 Range of Testing Equipments for Plastics
SPECIMEN PREPARATION PROCESS TEST EVALUATION
• Manual Hollow Die Punch • Melting Point Apparatus • Melt Flow Rate Index Tester
• Manual Notch Cutter • Specific Gravity • Shrinkage Oil Bath Tester
• Hollow Dies and Master Templates • Bulk Density • Accelerated Weathering Test
• Contour Cutter (UV Tester)
• Compression Press
• Two Roll Mill
• Notch Cutter for Pipes
MISCELLANEOUS
• CNC Contour Cutter
• Hydraulic Sheet Moulding Press • Opacity Tester • Hot Air Oven
• Deep Freezing Chamber • Constant Temperature
• Weighing Balance Water Bath
PHYSICAL AND MECHANICAL
• Microscope • End Caps for Pipes
TEST EVALUATION
• Methylene Chloride Test Bath • Sieve Analysis Tester
• Hydrostatic Pressure Testing for Pipes • Manometer for Water • Cone Tester
• Emitter Flow Rate Variation Tester Proofness Test
• Load Deformation Tester for DOT Pipes

profile
• Sliding C.O.F for Optical Fiber Ducting
• MDPE Gas Pipe Testing Equipment THERMAL TEST EVALUATION
• Elemendorf Tear Tester • HDT/ VSP • Carbon Black Content Tester
• Bursting Strength Tester • Carbon Black Dispersion Tester • E.S.C.R.
• Differential Thermal Analyzer • Temp. Malfunctioning Test M/C
Our story so far… Reasonable price, superior quality • Ash Content Tester • Oxidation Induction T ime
In our early days, we focused more on developing interrogative Yet another reason we provide for choosing our product is: control on the • Thermocyclic Test M/C Testing M/C
solutions to exclusive problems based on analogue outputs. in-house inspection and testing as a total quality management measure, PRODUCT TEST EVALUATION
These solutions gave us a great deal of creative satisfaction and making it mandatory for all individuals responsible for quality of their work. • Free Falling Dart for Pipe/Film
• C.O.F. Tester SPECIAL EQUIPMENTS
built for us a grateful and loyal clientele. After a few years of These procedures, that enable TQM, are continuously aimed at zero failure
working we realized that in this gigantic industrial market, and defect free performance, leading to superior products. • Tensile Tester We design and develop special
digitalization and computerization are required to do the continual • Flexural Tester equipments as per new testing standards
data analysis of test results. And we infused this realization into In the pursuit of quality DPPL has successfully implemented management • Compression Tester or customer requirements.
our business vision. Today, we have maintained our status as system satisfying quality system standard ISO 9001:2008 and by adopting • Izod & Charpy Impact Tester
leading producer of plastic testing equipments in India and are CE (European Complies) as a guide to its quality assurance activity. • Abrasion Tester
constantly spreading our wings to international market. • Flattening Test M/C
A tradition to follow, a reputation to keep
Area of work Through its unfailing adherence to quality, scientific temper and commitment
Product Testing Solution According to National & International Standards OTHER TESTING SOLUTION
Our core field is manufacturing of testing equipments for plastic to the customer, DPPL has built for itself a reputation that today precedes its • Rotational Moulded Watertanks Testing IS : 12701
and rubber industries. We produce a complete range of quality permutations. Numerous big and small companies across the world have
PIPE & FITTINGS TESTING SOLUTION • Flexible PVC Hose Testing IS : 15265 • Multilayer Co-extruded Film Testing
equipments with a wide range of applications. At the same time, adopted our user-friendly testing solutions to ensure the quality of their
• HDPE Pipe Testing IS : 4984 - 2016 & • PVC Sewerage Pipe Testing IS : 15328 IS : 2508 / IS : 2530
we maintain a cutting-edge R & D division, to meet specialized products.
IS : 14333 • C-PVC Pipe Testing IS : 15778 • Textile-tarpaulin Testing
technological challenges that come our way from time to time. As
• Sprinkler Pipe Testing IS : 14151 • PPR Pipe Testing IS : 15801 IS : 7903-2005 / 706 (P-8) / 1 5351
we matured into greater standardization and improved in-house
quality control, it totally transformed the way we did our business
Corporate culture • R-PVC Pipe Testing IS : 4985 : 2000 • Electrical Conduits Testing IS : 9537 • Woven Fabric Testing
“Each sale should begin a new relationship” that continues even after the • PLB Duct Testing (As per DOT Standard) (Part-1 & 3) • Solvent Cement Joints For Water Suppliers Testing
and gave us better control over production cost. In fact, for most of
transaction. This also gives us feedback of past sales that functions as • LLDPE Drip Pipe Testing IS : 12786 / 13488 • u-PVC Pipe Testing ASTM D 1785 IS : 7834
our new clients, our equipment prices came as a pleasant surprise
invaluable performance analysis. • Online Emitters / Drippers IS : 13487 • SWR Pipes Testing IS : 13592 • Special purpose machines for various application for
for them.
• Casing Pipe Testing IS : 12818 • SWR Fittings IS : 14735 pipe industries as per requirements.
DPPL's self-image and market confidence is based entirely on this feedback. • MDPE Pipe Testing IS : 14885/ISO 4437 • Structured Wall Plastics Piping • We offer full lab setups for all above products according
In this brochure we have sought to provide a glimpse of our testing • Conduit Systems for Electrical Installation Systems for Non-pressure Drainage to all national & international standards.
equipments. IS : 14930:2001 (Part-1 & 2) and Sewerage Testing IS : 16098:2013
1 www.deepakpolyplast.in (Part-1 & 2) Deepak Poly Plast Pvt. Ltd. 2
 These machines are designed to test a wide range of materials
including, but not limited to: Plastics, Films, Paper, Packaging Materials,
Non–woven Fabrics, Filter Material, Belt, Leather, Adhesives, Foils, Food
Universal Tensile Tester Packaging, Toys, Plastic Drum & Containers, Medical products and
Electrical Components etc. in Tensile, Elongation, Modulus of Elasticity,
Single Screw Models
Flexural Strength, Compression Strength, Co-efficient of Friction,
The single column material testing machines having frame
Sealing Strength, Shear and Peel-off Test, Toung Tear, Grab Test,
capacities of 1 KN to 5 KN, available in range of DTRX (Table Top)
Butt-fusion, Elongation @ Break, Weldability, Pull-out, Ring Stiffness,
& DUTT (Floor Mounting) series.
Creep Ratio, Special Force Measure Test, etc.
Single Screw Table Top Models
With computer interfacing & variable speed drive system.
DTRX and DUTT Series
Using a combination of quality engineering and advanced technology,
• DTRX - 1 KN for film testing application. Deepak has produced a series of machines that are accurate and
• DTRX - 1 KN for tape testing application. simple to use. All DTRX and DUTT series machines have an easy-to-read
• DTRX - 5 KN with single load cell for fabric testing application. backlit liquid crystal display feature. All data shown on this display is
• DTRX - 5 KN with single load cell for PTFE liner testing application. obtained in real time. The control unit has dedicated keys for moving the
• DTRX - 5 KN with single load cell for low thickness SWR pipes crosshead Up, Down, Stop and Start the test. The DTRX and DUTT series
testing application. are equipped with lead screw travel & AC frequency drive (close loop
• DTRX - 5 KN with dual load cell for tape & fabric testing application. feedback system optional) to have speed selection and control. DTRX
• DTRX - 5 KN suitable for MOV, MOR & WET bending strength and DUTT Series models are having speed selection range from
testing in plywood testing application. 1 mm/min to 500 mm/min (as per application and requirement).
DTRX 1KN-TT DTRX 5KN-TT DTRX 10 KN-TT DTRX-10 KN/20 KN/30 KN/50 KN
(Single Load Cell Model) Single Screw Floor Mounting Models
• DUTT - 101 (with comp. interfacing software + variable speed)
• DUTT - 104 (without computer interfacing + variable speed)
with LCD / digital display of readings.
S–DTRX Series
Twin Screw Twin Bar Models DEEPAK has developed servo motor based S-DTRX series of
The dual column material testing machines having frame machines. These S-DTRX series models are equipped with servo
capacities of 10 KN to 300 KN, available in range of DTRX & control system to have better speed accuracy and control with
S-DTRX (Floor Mounting) series . additional software features. These models are having speed
selection range from 0.5 mm/min TO 500 mm/min.
• DTRX - 10 KN / S-DTRX - 10 KN Model
For PP strap, casing PVC pipes, C-PVC pipes, injection Common Features
moulding articles, etc. testing application. DTRX, S-DTRX and DUTT series machines are suitable to
• DTRX - 20 KN / S-DTRX - 20 KN Model communicate directly with standard desktop/laptop PC running
For PET strap, wood composites, special applications with Windows XP/7/8.1 software packages via high speed RS 232
from defence, etc. testing application. communication port/USB port. DTRX and DUTT series machines are
• DTRX - 30 KN / S-DTRX - 30 KN Model equipped with rapid change Z beam load cells that allow simple and
For automobiles & engineering plastics t esting quick ‘Sizing’ of the machines to an appropriate capacity for the test.
applications. These load cells have accuracy of +/- 0.5% of the applied load value,
• DTRX - 50 KN / S-DTRX - 50 KN Model from 2% to 100% of the load cell capacity.
For universal applications with multi load cell f ittings –
suitable for belt / fabri c / tape testing application. DTRX and DUTT series have a huge assortment of specimen grips
• S-DTRX - 100 KN / 200 KN / 300 KN Model and fixtures allowing the selection of an ideal configuration for your
For PVC column pipe pull-out testing / column pipe application.
thread testing application. Machines are a vailable with
DUTT 101 For Plywood Test Applications suitable pull-out fixtures.
S-DTRX - 10 KN/20 KN/30 KN/50 KN S-DTRX - 100 KN/200 KN/300 KN
(MOV & MOR Test)
3 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 4
 Dual Load Cell Table Top DTRX-5KN Machine
Features:
• Equipped with seperate grips for fabric & tape
test application.
Pull-out Test Application of Column Pipes
• Selector switch on panel to select type of test as Technical Details
per requirement. • Load Cell Capacity: 10000 / 20000 / 30000 Kgf.
• Selector switch gives option to select type of
(10 / 20 / 30 Tons) Maximum.
sensor, suitable for Fabric “or” Tape/Yarn Test
Application. (Round Bar Type Load Cell).
Note: No need to interchange the Grip “or” Load • Motor: AC Servo Motor.
Cell. Both test applications are having separate • Power Requirement: 220/230 V AC, 50 Hz Single Phase.
location of Load Cell & Grips. • Inbuilt Testing Facility for Compression/Flattening/Ring
Stiffness Test for the same provision of mechanical square
Multi Application Machine
high polish platons.
with Triple Load Cell & Triple Grip Sets
Suitable for tensile, elongation, modulus of elasticity • With fixtures for pipes Sizes: 1”, 1¼”, 1½”, 2”, 2½”, 3”,
etc. test applications for Webbing Belt, Fabric & 4”, 5” & 6”.

DTRX 5KN-TT Tape-Yarn Specimens

(Dual Load Cell Model) Motorized Compression Cum Flattening Test
DTRX 30KN/50KN Machine for c-PVC / u-PVC Specimen Testing
(Triple Load Cell Model) • Twin Screw Floor Mounting Structure suitable for S-DTRX - 100KN / 200KN / 300KN
up to 12 Inch Dia Pipes.
• Equipped with Flattening Platons: With Stationery
Platon & Moving Platon Assembly
• Equipped with 2 HP AC Motor Driven & With Heavy Software
Gear Box System. DEEPAK has a long history of providing solutions
• With Electrical Control Panel for smooth operation to an enormous variety of testing problems with
and with inbuilt limit switch safety features. specific and focused applications. By designing
• Power requirement: 415 V AC, 50 Hz Three Phase focused application software in co-operation
+ neutral + earthing is required. with our valued customers around the world.

There are several valuable features that are

common to all, perhaps the specialty is the
ability to further customize the testing
parameters that are used to collect and store
operation testing data, as well as to control the
testing machine.

All versions of our focused application software

are developed or customized to improve
productivity and to build strong database.
• After completion of test, report will be
• This is windows based software, compatible generated in windows excel sheet, which
with Windows XP/7/8.1. accommodates graph view & results table I-COF Testing Machine - Single Screw Equipped
• Unit conversion facility. view in single page. with 450 Degree Angle Drum - for PLB Pipe Testing
• Online graph plotting system on your pc • Buyer’s company name & logo, can be added • Equipped with dead weight of 25 Kgs. for internal
Ring Stiffness & Ring Flexibility / Creep Ratio Compression cum Pulling Force Testing Machine Compression system with result comparison upto 5 in software. co-efficient of friction test between pre-lubricated
Testing Machine Suitable For PE DWC Pipes / Suitable for PE Drum / Container Testing Application, cum Flattening samples and has an ability to recall, re-plot • Generated excel report can be converted in to PLB pipe and optical fibre cable.
PE – PVC Electrical Conduit Trunking Pipes / as per IS: 6312 – 1994 Standard. Test Machine and re-scale curves. pdf format & the same can be forwarded as an • Suitable for 32, 40 & 50 mm PLB pipe holding.
PVC Sewerage Pipes. • Graph line colour selection. attachment by e-mail facility.
5 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 6
 GRIPS FOR GRIPS FOR
Standard Features Range of Grips
UNIVERSAL TENSILE • PC compatible via high speed RS 232 UNIVERSAL TENSILE
• Mechanical Wise Type Grip Set
TESTER com port/USB port.
• Combine Grip Set For Elongation At Break Testing
TESTER
• Machines are proof loaded at 200% of their
& Butt Fusion Testing
capacity.
• Force accuracy of 0.5% of applied load across • Centering Pin Type Grip Set
the load cell display range. • Grip Set For Tape Test
• Built-in protection for over load and over travel. • Fabric Grip Set
Load at constant speed
• Displacement resolution of 0.01 mm for • Leather / Rubber Coated Grip Set for Films Testing
S–DTRX series & 0.1 mm for DTRX & DUTT Dumbbell Cutters/Die Punches • Special Roller Type Holding Grip Set for Yarn Testing
L1
series. a L1
• Heavy Grip Set for Webbing / Belt Testing
• Specially designed Windows XP/7/8.1 based Vice for Flexural Test
• Special Grip Set for Plywood Testing
software for DTRX and DUTT series machines. b
(MOV/MOR Testing)
• Customized grips and fixtures according to Load

products and reference standards. • Special Grip Set for PE Container Side Handle
Pulling Test
• Grip for Trapezoidal Test
• Grip for Grab Test
• Grip for Stitching Yarn
• Grip for Wide Width Strength
• Grip for CBR Puncture Test
Dumbbell Cutters/Die Punches • Grip for Index Puncture Test
• Grip for PP Tape Testing

Specifications
Load measurement accuracy:
+/- 0.5% of applied load from 2% to 100% capacity,
extended range down to 1% capacity with accuracy Range of Die Punches
of 1% of applied load. • Dumbell Shape Specimen Punching as per
Compression Test Attachment ASTM D 638
Position measurement accuracy: • Type ‘I’ Overall Length: 165 mm
+/- 0.1% of reading or 0.01 mm in S–DTRX series & • Type ‘II’ Overall Length: 183 mm
0.1 mm in DTRX and DUTT series. • Type ‘III’ Overall Length: 246 mm
• Type ‘IV’ Overall Length: 115 mm
Speed accuracy:
+/- 0.1% of set speed. • Type ‘V’ Overall Length: 63.5 mm
• Die Punch as per ISO-527-2 Standard
Load measuring systems: • Tear Strength Test Die Punch as per
Load measuring system meets the requirements of ASTM D 624 (Die-C)
ASTM E4, ISO 7501. • 75 mm, 150 mm Die Punch and many more as
per IS and International Standards
Strain measuring system:
Strain measuring system meets the requirements of
ASTM E83.
Puncture Test Hydraulic Cylinder Operat ed Manual Press for Specimen
Attachment Press Machine for Specimen Die Punching Application
Note: Specifications are subject to change without
Die Punching Application prior notice.
7 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 8
 Izod-charpy Impact/Tensile Pendulum Impact
The new model of Pendulum Impact tester is built with versatility, ease of operation and display Falling Dart Impact Tester for Films
of information with high resolution.
Generally Plastics Films are used for ‘Packaging Application’, and undergo wear & tear. Hence study of
‘Impact’ Resistance is established to evaluate the quality and mechanical property of the film.
These machines are capable of determining the impact strength using Charpy, Izod or Tensile
Pendulum Impact methods by changing the pendulum striking tab.
This method covers the determination of the energy that causes Plastics Film to rupture under specific
conditions of impact of a Free Falling Dart (load). This energy is expressed in terms of weight (mass) of the
By using the appropriate striking tab and the specimen clamps on the base of the machine,
missile falling from a specified height which would result in %age specimen's failure tested.
plastic samples can be tested in accordance with -
Features
ASTM D 256 Izod Impact ASTM D 4812 Un-notched cantilever • The evaluation of ‘Impact Strength’ of different types of Plastics Films & Sheet, Decorative Laminates,
ISO 179 Charpy Impact beam Impact Corrugated roofing sheets etc.
ISO 180 Izod Impact ASTM D 4508 Chip Impact • Dart with different weights are available to drop from different height to study the fracture of the product.
ASTM D 950 Adhesive bond Impact • To clamp film specimen tightly, ‘Vacuum Clamping System’ is provided with ‘Vacuum Ring & Gauge’.
ASTM D 6110 Charpy Impact
• Electromagnetic Dart Holder is provided so as to hold the dart and drop at press of button.
• Evaluation can be carried out as per ‘IS-2508, ASTM D-1709 & BIS-2782’ standards.
Pendulum capacity can be easily change & increased by adding
Izod-charpy Impact the optional weights on Pendulum Hammer Device. The energy Accessories
absorbed for breaking can be configured in different units of Accessories can be provided as per different standard requirement.
measurement and the same is displayed by an optical encoder
mounted on the shaft of the machine. Specification
• Dimension (W x D x H): 22 x 20 x 84 (inch)
Key Features • Dart: As per IS – 2508 and ASTM D 1709 standard
• Selectable energy units – J, in.lbf, ft.lbf, kgf.m, kgf.cm • Supply: 220/230 V AC, 50 Hz Single Phase
• Selectable strength calculation in J/m, Kj/m², kgf.m/m² • Approx Weight: 75 kg
Falling Dart Impact Tester for Films
• Auto calibration for bearing wind edge and friction

Technical Specification
Pendulum Capacity Maximum up to 25 Jules
E Drop Height 0.61 meter
Impact Velocity 3.46 m/s
Hammer
Power 220/230 V AC, 50 Hz Single Phase Elmendorf Tear Tester
Tensile Pendulum Impact
It is used to determine ballastic tearing strength and work factor of fabrics elmendorf method, supplied
with calibration weights and augmenting mass to test upto 6400 gms.

Notch Cutter This test method has been widely used as one index of the tearing resistance of plastic film and sheeting
used in packaging applications. While it may not always be possible to co-relate film tearing data with its
The linear notching machine is designed to prepare rapid and other mechanical properties. This test method provides a controlled means for tearing specimens at
accurate notched specimen for impact resilience determinations straining rates approximating some of those found in actual packaging services.
according to Izod-Charpy impact methods.
• Pendulum of 1600 gf, 3200 gf and 6400 gf capacity
Reference standard (as a extra weight).
ASTM D 256 & ISO 179. • Pointer reset mechanism.
• Sturdy & compact design.
Manual operation based on • Rigid cast iron body to bear the vibration of pendulum swing.
hand wheel. • Provided along with ASTM and BS Templates.
Motorized operation based on • Reference standard ASTM D 1922 & IS 2508.
panasonic geared motor.
Notch Cutter Digital Notch Cutter Elmendorf Tear Tester
9 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 10
 Co-Efficient of Friction Tester (Slip Tester)
Features
• Microprocessor based programmable LCD digital display unit with memory back-up.
• With computer interfacing software facility (Rs-232 to Rs-485 convertor system).
Shrink Oil Bath Apparatus
• With master software CD & interfacing cable with USB connectivity. • Oil Bath inner chamber size : 12 x 12 x 08 inch. Capacity: Max. 18 Ltr.
Co-Efficient of Friction Tester • Variable speed control system with AC drive digital speed indicator. • With Digital PID Temperature Cont., Temperature Panel Fitted.
Speed selection: 10 mm /min TO 300 mm/min. Temperature Working Range: Ambient Room Temperature to 150°C.
Deepak friction tester is primarily designed to determine the
• Sled movement of 300 mm/min. • Maximum Working Temperature Range : Upto150°C with +/- 1 °C
co-efficient of friction of plastic films, sheets, laminates, pipes
• With overload protection system for load cell.
and paper etc. The equipment provides measurement of static Accuracy.
• With auto-stop facility after 300 mm travel.
and kinetic co-efficient of friction. The apparatus conforms to • To keep uniform temperature in oil bath, Remi make regulated stirrer
• Electronic flat bar type load cell, available with 700 “or” 1500 gmf capacity.
BS 2782 and ASTM D –1894 and other equivalent standards. motor fitted on top SS sheet cover.
• Panasonic make compact AC geared motor & compact gear box system
• Inside SS (SS-304) & out side MS body with high temp. resistant PU- Cone Tester
• Sled with steel and rubber combination.
Measurement of frictional properties may be made on a film or Sunsilk paint with 1.5 inch thick glasswool insulation on all side walls
• Movement of Sled is based on friction less linear guide system to avoid play in running mode.
sheeting specimen when sliding over itself or over another of Oil Bath structure.
• S.S. High Polish Moving Platform with guide and scale with auto reverse on/off
substance. The co-efficient of friction are related to the slip • Power Requirement: 220/230 V AC, 50 Hz Single Phase.
selection facility.
properties of plastic films that are of wide interest in packaging
• Attachment available for peel of strength of plastic adhesive film, at extra cost. Shrink Oil Bath Apparatus
application. These methods yield empirical data for control
• Power Requirement: 220/230 V AC, 50 Hz Single Phase
purpose in film production. Co-relation of test results with actual
performance can usually be established.

Electronic Weighing Balance

With density measuring system.
Model: 200/220 gms for specific gravity/density test application
• With density kit.
• Max. Capacity: 200/220 gms.
• Readability: 0.0001 gm (0.1 mg)
• Power Req.: 12V / 0.84 A.
• Direct display of calculated density result.
• Suitable for mass density test application.

Opacity Tester for Film Opacity Tester for PVC Pipe

Opacity Tester for Films Opacity Tester for PVC Pipes

Deepak Opacity Tester is used to determine optical (As per new amended standard of IS 4985 April 2012)
characteristics of plastics films. Procedure is based on • Compact table top model.
transmission of light through the specimen. • New version as per amendment of standard IS : 12235 (PART 3) 2004 Electronic Weighing Balance
• Digital display with direct % reading facility. Manometer Pressure
Specifications • Dust free chamber with openable cover to protect sample during test. Test Machine for Water
• Reference Standards: ASTM D 1746, ASTM D 2530, IS 2508 Also avoid unwanted light passing through sample. Proofness Testing
• Power Requirement: 220/230 V AC, 50 Hz Single Phase • With in-built specimen mounting spring type clamp (fitted in specimen
mounting chamber).
GSM Cutter with Rubber Pad
11 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 12
 Environmental Stress Cracking Resistance
This apparatus is used for determining the susceptibility of ethylene plastics, to Environmental Stress
Cracking when subjected to certain conditions. Bent specimens of the plastic having controlled
imperfections are exposed to the action of a surface-active agent. These tests are normally employed for
Carbon Black Content Tester
routine inspection purpose. Standards
Designed and manufactured as per the following
Environmental stress cracking is a property that is highly dependent upon the nature and level of the Stress standards:
applied and on the thermal history of the specimen. This equipment consists of a heating bath to hold water • IS 2530 / 2508
or surface active liquid used for the test. • ASTM D 1603 or equivalents

• Model with Accommodation of 08 Test Tubes • Model with Accommodation of 16 Test Tubes Features
Size : 12(L) x 12(W) x 14(H) inch. Size : 20(L) x 20(W) x 15(H) inch. • Compact tubular furnace to get temperature up to
800º C with microprocessor based PID temperature
Temperature Room temperature to 100.0° C controller.
Timer In-built timer with temperature controller • The furnace contains 2.0 KW heating element
synchronize with temperature wound on a tubular ‘Quartz’ tube.
Environmental Stress Cracking R esistance Carbon Black Content Tester • Provided with nitrogen gas purification and
Test Accessories As per standards all test accessories
moisture absorption system.
Blanking Die, Nicking Jig, Specimen Holder
Deepak Carbon Black Content Tester has been designed incorporating many features and • Specimen is heated in controlled nitrogen
Test Tubes with Test Tube Holder Rack & atmosphere (inert atmosphere).
Rubber Corks, Bending Clamp, Transfer Tool new ideas. The apparatus conforms to the most recognized national and international
E.S.C.R. Tool Kit standards including BIS, ISO, ASTM, etc. • Instrument is heavily insulated with glass wool and
insulation/fire bricks.
• Reference standard ASTM D 1693. To determine the average of carbon black content especially in polyethylene materials by • Relevant glass wares and gas flow regulator meter
• Power Requirement: 220/230 V AC, 50 Hz Single Phase. pyrolysis method, like plastic pipes, films, sheets, cables, water tanks etc., this equipment provided with the machine for purification and
is very useful for evaluation of carbon black content. Carbon black is used in plastic as a UV regulation of the nitrogen gas.
stabilizer to prevent degradation of plastic by UV radiation. It is also possible to find out ash • Power Requirement: 220/230 V AC, 50 Hz Single
Melt Flow Rate Index Tester content in plastic material by this instrument. Phase.

Deepak Melt Flow Tester, built according to Features

international standards, is an instrument for • Microprocessor based PID Temperature Controller.
measuring ‘Melt Flow Rate’ with high accuracy
and also useful for quality control test on flow
• Temperature range up to 400ºC. +/- 0.1º C.
• Built-in microprocessor based cyclic timer with buzzer
Carbon Black Dispersion Tester
ability, grading of thermoplastic materials
output. Deepak Carbon Black Dispersion Standards
according to flow. In general, it is designed to
• Optional attachments for automatic cutting device Instrument is used to find out the Designed and manufactured as per the
calculate accurate rate of extrusion of molten
and computer interfacing are available with extra cost dispersion of additives e.g. pigments, following standards:
resin through an orifice at specified
as per ASTM D-1238 (B method). fillers in plastics. In plastic material, • IS 2508/2530.
temperature and pressure. Standard
• Power Requirement: 220/230 V AC, 50 Hz Single pigment and fillers play a very • ASTM, BS or equivalent standards.
equipment includes all operating tools, piston
Phase. important role for matching the
and dies. Integrated microprocessor based
Melt Flow Rate Index Tester PID temperature controller/timer incorporates uniform colours as well as resistance Hot Plate
Test Accessories as per international standard with
latest digital technology. Operations up to against UV light. Thermostatically operated with indication lamp
proper dimensions, material and accuracy.
400º C with control and display with an and on /off switch.
• Piston Rod With Reference Markings
accuracy of 0.1º C. This equipment is also useful for Hot plate diameter: 8 inch, coated with enamel
• Barrel Cleaner, Die Cleaner & Material Charging Tool
determination of surface defects, coating.
• Specimen Cutting Knife
Standards • 2.09mm Die Orifice voids, bubbles, filler distribution and
Designed and manufactured as per the other structural investigation. Projection Microscope
• Material Feeding Hopper ( Aluminium) Projection screen dia: 4 or 6 inch.
following standards: • Testing Loads ( Dead Weights) of 1.2 KGS, 3.8 KGS,
• ASTM D 1238 Method A & B • ISO 1133. Magnification: 100x, 200x, 450x available.
2.16 KGS , 5.0 KGS & 10.6 KGS Light source: 6 V or 12 V Halogen Lamp.
MFI Toolkit • IS 2508/2530. • Back Panel Cover Key
Carbon Black Dispersion Tester
13 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 14
 Hot Air Circulating Oven
Deepak Hot Air Circulating Oven is used for multipurpose tests for plastic
Methylene Chloride Tester
material such as shrinkage, reversion, migration, warpage, moisture content The Methylene Chloride Test is meant to check the gelation in rigid PVC
and lateral E.S.C.R. pipes. This method is based on various national and international
standards, where specified test temperature and duration concludes
Test at different temperature. Triple walled construction and forced air resistance of unplasticized PVC pipes against dichloromethane.
circulation provide uniform temperature throughout the chamber.
A piece of PVC-U pipe of specified length, chamfered at one end to an
Features angle dependent on its thickness, is immersed for a fixed period of time in
• Temperature range: Ambient to 199.9°C. a thermo controlled dichloromethane bath in order to verify that the PVC-U
• Temperature controlled by ‘Digital PID’ based temperature controller. is not attacked at the temperature Ө specified in the product standard.
• Choice of M.S., Aluminum or SS Interior body.
The test pieces are dried in air and then examined to observe whether the
PVC has been attacked or not.

Available chamber sizes are : 350 x 350 x 200 mm, 650 x 650 x 300 mm
& 650 x 650 x 500 mm
Methylene Chloride Tester

Special Hot Air Oven Standard Chamber Size (L x W x H)

for DWC Testing Application • 350 x 350 x 350 mm (14 x 14 x 14 inch)
• 450 x 450 x 450 mm (18 x 18 x 18 inch)
• 450 x 450 x 600 mm (18 x 18 x 24 inch)
• 600 x 600 x 600 mm (24 x 24 x 24 inch)
• 600 x 600 x 760 mm (24 x 24 x 30 inch)
Bulk Density / Dry Flow / Flowability /
• 1000 x 1000 x 1000 mm (39 x 39 x 39 inch)
• 1065 x 600 x 600 mm (42 x 24 x 24 inch)
Pourability Test Apparatus
• 1980 x 760 x 910 mm (78 x 30 x 36 inch) It is easy to determine fast and accurate bulk density of plastics raw materials with
• 2260 x 1240 x 1490 mm (89 x 49 x 59 inch) the Deepak Bulk Density tester. You can control the uniformity of the raw material
from different stocks and deliveries according to standards.
Hot Air Circulating Oven
System Specifications

Muffle Furnace Capacity of hopper

Capacity of measuring cup
Approx. 115±5 ml
Approx. 100±5 ml
System Specifications Dimensions Height-250 mm, Width-150 mm, Depth-140 mm
Temperature range Ambient temperature to 1000°C Weight 2 kg (approx.)
Temperature resolution 1°C Calculation Apparent density = (G1-G0):100 in g/ml
Furnace size 9” x 4” x 4”, 12” x 6” x 6” & 18” x 9” x 9” Or = (G1-G0) x10 in g/ml
Furnace construction Inside SS outside MS with powder coating
Features
Insulation Heavily insulated with glass wool and fire bricks
• According to ASTM D1895, ISO R-60, IS-466, ARM standard, etc.
Power supply 220/230 V AC, 50 Hz Single Phase • Easy handling.
Weight 50 kgs (approx.) • Compact structure.
Muffle Furnace • Made of high quality, polished corrosion free materials.
• With anodizing treatment as per requirement.
Bulk Density
15 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 16
 Hydro Static Pressure Hydro Static Pressure Hydro Static Pressure Testing Machine - 6 Stations Hydro Static Pressure Testing Machine - 4 Stations Hydro Static Pressure Testing Machine - 8 Stations
Testing Machine - 2 Stations Testing Machine - 3 Stations Model: Hydro-106-D-SD Model: Hydro-104-D Model: Hydro-108-D with Pressure Booster Station & High Pressure Accumulat or
Model: Hydro-102-D-SD Model: Hydro-103-D-SD
• Facility of report generation is available in two formats (1) in software format & (2) in Microsoft excel with graph and test data.
• Option of two type of booster for accumulator (1) motorize pump system which requires only water inlet & (2) pneumatic pump system which
Hydro Static Pressure Testing Machine requires air and water inlet to generate pressure.

Model : hydro-xxx-d-sd digital version only. Based on hydro-pneumatic cylinder pump unit. All stations are suitable for long term & short term
Deepak Hydro-static Pressure Testing Machine is designed specifically for testing pressure test application. Pressure range: from 1 to 300 bars. L.c. : min. 0.01 to max. 0.1 bar.
HDPE, PVC, PPR, Lateral pipes as per IS 4985, IS 4984, IS 12786, IS 13592,
IS 14333, IS 14151, IS 15328, IS 15801, EN 921:1994, ASTM D 1785 and other Model Pressure Stations Version Accumulator Unit. Power Req.
relevant standards. Hydro-static Pressure Testing Machine is used to maintain the HYDR0-106-D-SD 06 Digital Yes 1 Phase 220/230 V Ac 50 Hz.
required pressure in pipes. HYDR0-105-D-SD 05 Digital Yes 1 Phase 220/230 V Ac 50 Hz.
Positive/Negative Pressure HYDR0-104-D-SD 04 Digital Yes 1 Phase 220/230 V Ac 50 Hz.
Features Testing Machine for
• Standard equipment includes versatile microprocessor based controller with Elastomeric Ring Type Socket Joints, HYDR0-103-D-SD 03 Digital Yes 1 Phase 220/230 V Ac 50 Hz.
high performance to price ratio. This is a single chip micro-controller based suitable for HYDR0-102-D-SD 02 Digital Yes 1 Phase 220/230 V Ac 50 Hz.
controller designed for 4-20 mA inputs. Four user-friendly key operated PVC Sewerage Pipes (IS:15328)
HYDR0-101-D-SD 01 Digital Yes 1 Phase 220/230 V Ac 50 Hz.
instrument, where keys are used for programming of pressure display unit of & DWC Structural Pipes (IS:16098)
each channel. Model: Hydro-101-D
Model : hydro-xxx-d digital version with computer interfacing facility. Based on motorised water booster pump unit. All stations are suitable for
• Separate versatile microprocessor based controller for each station with high long term & short term pressure test application. Pressure range: from 1 to 300 bars. L.c. : min. 0.01 to max. 0.1 bar.
accuracy pressure control up to 0.10 bar. Model Pressure Water Bath Version With Computer Power Req.
• Option of one to three pressure outlets with each station, or as per customer Stations Temp. Stations Interfacing Software
requirement.
HYDR0-110-D 10 02 Digital Yes 3 Phase + Neutral + Earthing
• User friendly Windows XP/7/8.1 based software suitable up to 32 pressure
stations and 08 temperature stations in software. All the stations can be • Negative Pressure Test Machine – Equipped with in-built HYDR0-108-D 08 02 Digital Yes 3 Phase + Neutral + Earthing
operated from single bar graph window from computer display and all pressure vacuum pump unit for negative vacuum pressure generation. HYDR0-106-D 06 02 Digital Yes 3 Phase + Neutral + Earthing
control parameter can be set by few selected mouse clicks. • Positive Pressure Test Machine – Equipped with inbuilt airless
Motorized Pump / Hydro-pneumatic Cylinder Unit for positive HYDR0-104-D 04 01 Digital Yes 3 Phase + Neutral + Earthing
• PC connectivity is not required for entire test duration with machine. After pressure generation. HYDR0-103-D 03 01 Digital Yes 3 Phase + Neutral + Earthing
completion of test, data can be downloaded from machine to PC. Machine • With digital programmable (cyclic programming) display
display micro controller is with inbuilt memory card, suitable up to 3000 data HYDR0-102-D 02 01 Digital Yes 3 Phase + Neutral + Earthing
controller for test cycle programming for negative & positive
storage. pressure test. HYDR0-101-D 01 01 Digital Yes 3 Phase + Neutral + Earthing

17 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 18

 Room / Hot / Cold Water Bath
Analogue Gauge Version Manual Dun-key Type
Deepak hot/cold water bath is used for short term and long term
Hydro Static Pressure Test M/c -
For Water Tightness of Joints Test
hydro-static Pressure test of HDPE, R-PVC, C-PVC, MDPE and Lateral
Pipes. They are tested at higher or lower (cold) temperature in water
• Short term single station with single outlet.
bath as per IS, ISO and ASTM Standards.
• Range of Analogue SS Pressure Gauge: 0-4 Kg/cm2.
L.C.: 0.02 Kg/cm2.
Length (inch) Width (inch) Height (inch)
• Based on Manual Dun-Key Type Water Pump
Pressure Generation System. 60 30 46
• With digital stopwatch for test duration observation. 60 30 60
48 30 18
36 24 18
Hot Water Bath Cold Water Bath 40 20 40
Size : 78 x 36 x 60 inch Size : 78 x 36 x 60 inch
40 24 40
40 24 18
48 36 22
48 36 20
48 36 18
44 20 18
30 20 18
14 14 12
72 40 40
78 39 60

Features
Test Bench for Leak Tightness of Joints against • Microprocessor based temperature controller with PID action.
Angular Deflection (with P ositive & Negative Hydro Static Pressure Testing Machine - Hot Water Bath Hot / Cold Water Bath • Temperature range up to 100°C with least count of +/- 0.1°C and
Pressure Applied) Single Station Model: Size : 40 x 20 x 40 inch Size : 60 x 30 x 46 inch accuracy +/- 2°C.
Test Bench for Fittings Pressure
Hydro-101-D-SD for Busting Test Test Application • Inside S.S. body, outside M.S. body with powder coating and puff
insulation (injected puff).

Hot Water Bath for Temp. Malfunctioning Test • Complete inner and outer S.S. body
bath.
For CPVC pipes & fittings - Water circulation test at 95 & 82°C • ‘GRUNDFOSS’ make water
with inner water circulating pumps fitted + with external high pressure circulating pump is provided in
Grundfoss water pump fitted. Hot/Cold water bath to achieve the
temperature uniformity in entire
water bath.
Water Circulating Pump GRUNDFOSS - CRCM - 1 • Heating, cooling or both facilities can
• Model: A96127254 P 10818 | Type: CRCM1, 1.10 Kw Capacity be provided as per the requirement.
Hot Water Bath for • Power Requirement: 220 V AC - 50 Hz - Single Phase. • Power requirement: 415 V AC, 50
Temp. Malfunctioning Test • With attachment of ½” inch hose coller connection for inlet & outlet. Hz Three Phase + neutral +
Size : 40 x 20 x 40 inch • With Flow Control Needle / Ball Valve Mounting & Brass Block Mounted earthing is required.
• 0-20 bars electronic pressure display unit fitted. Hot/Cold Combined Water Bath Room Temperature Water Bath
Complete Stainless Steel Body Suitable for Short Term Pressure Test
19 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 20
 Humidity Chamber Unit
(For Specimen Conditioning)
• Inner chamber of SS, outer MS body with
powder coating.
• With digital indicator for RH value & temp.
read out.
• Temp. range: 25°C to 45°C.
• Humidity readout range: 45% RH to 80% RH.
• With blower system for uniform temperature.
• With inner glass door for easy visibility.
• With two SS shelves (racks).
• Inner chamber size:
Deep Freezing Chamber Deep Freezing Chamber Deep Freezing Chamber 18 X 18 X 18 inch
Front Opening Front Opening Top Opening 18 X 18 X 22 inch
18 X 18 X 40 inch
• Power Requirement: 220/230 V AC, 50 Hz
Single Phase.
Deep Freezing Chamber (For Specimen Conditioning) Humidity Chamber Unit

Deepak Zero Degree Chamber is specially used to condition the R-PVC pipes at 0°C. for impact testing as per IS 4985
standard.

A true material comparison is possible only when test values are determined by identical test methods under identical
conditions. In general, physical and mechanical properties of plastics and electrical insulating materials are affected by Reversion Oil Bath Reversion Oil Bath
temperature and humidity. Plastic materials tested above/below room temperature will yield relatively higher impact
Digital PID based temperature controller with 0.1°C least count. Vertical Model
strength and lower tensile strength as well as modules. In order to make reliable comparisons of different materials and
test results obtained by different laboratories, it is necessary to establish standard conditions of temperature and
Features
humidity for testing.
• Temperature range: Max. up to 200°C.
• In side SS out side MS with powder coating.
Features • For uniform temperature stirring is provided.
• Microprocessor based temperature controller with PID action. • Actual Inner Size: 26(L) X 20(W) X 16(H) inch
• Temperature range: Room temperature to –5°C or -20°C. Working Area: 18(L) X 20(W) X 16(H)
suitable up to 250 mm pipe testing with oil filling capacity up to 140 Ltr.
Standard Chamber Size • Actual Inner Size: 28(L) X 22(W) X 32(H) inch
• 18 x 18 x 18 inch (Front opening single door model). Working Area: 22(L) X 22(W) X 32(H)
• 20 x 15 x 30 inch (Top opening single door model). suitable up to 400 mm pipe testing with oil filling capacity up to 180 Ltr.
• 46 x 20 x 26 inch (Top opening single/two door model). • Actual Inner Size: 42(L) X 34(W) X 27(H) inch
• 70 x 30 x 32 inch (Top opening three door model). Working Area: 34(L) X 30(W) X 27(H)
suitable up to 315 mm pipe testing with oil filling capacity up to 180 Ltr.
• Power Requirement: 220/230 V AC, 50 Hz Single Phase. • Size can be modified according to customer requirements.
• Insulation: glass wool insulation.
• Power requirement: 415 V AC, 50 Hz Three Phase +
neutral + earthing is required. Reversion Oil Bath
Deep Freezing Chamber Horizontal Model
Complete inner & outer S.S. body with 2 & 3 Door Openings

21 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 22

 MS Block Type Hose Coller Cone Type Block Fitting Aluminium Design Cup Type
for HDPE/R-PVC/PPR/u-PVC/C-PVC for Lateral Pipe Test Application for HDPE/R-PVC/PPR/u-PVC Test Application
Test Application

End Plugs
• End Plugs suitable for R-PVC, C-PVC, u-PVC, H.D.P.E, Lateral,
Sprinkler, PPR, M.D.P.E., SWR, etc. Pipes and Joints.
• Sizes are available from 12 mm to 1200 mm pipe diameters.

Types
• MS Block type with double rubber gasket.
• Aluminium design cup type with double rubber gasket.
• Investment steel casting (SS-304) with double rubber gasket.
• Hose coller block type end plugs for lateral pipes. Analogue Version Single/Two Stations Digital Version with Computer Interfacing

VICAT
HDT / VSP Tester (Analogue / Digital)
1.00 -
Deepak HDT/VSP instrument is used for determining the deflection temperature limit for
Cone Type Flange Fitting for 0.90 -
specific application and comparing the heat softening characteristics of thermoplastic
HDPE/Sprinkler Pipe Test Application 0.80 -
material at a constant load in oil media up to 300º C.
0.70 -

Deflection (mm)
0.60 - Plastic materials, being heat sensitive in nature, have a lot of bearing on thermal
0.50 - Stat - 1 environment for their performance. Though their behaviour in thermal conditions is very
0.40 -
Stat - 2
complex, some simple yield tests are used to predict its behaviour and performance in a
0.30 -
given condition. ‘Vicat Softening Point’ or ‘Heat Deflection Temperature’ is one of such yield
0.20 -
points, very commonly used for engineering plastics. Vicat test consist of penetrating a unit
size indenter in a plastic surface with predefined load under constant rate of environmental
0.10 -
temperature rise.
0.00 -

51.6 54.7 57.7 60.7 63.8 66.8 69.9 72.9 75.9 79. 82. Heat distortion test, as it is sometimes called, consists of deflecting a simply supported
Temperature (cent.) beam of test material under similar heating conditions and with a predefined stress
application.

Available range of VSP Tester – Single Station, Two Stations, Three Stations, Four Stations &
Eight Stations.
Investment Steel Casting End Plugs for HDPE/R-PVC/u-PVC Test Application
23 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 24
 20 Ton Compression Moulding Press (Lab Model)
Deepak Compression Moulding Press is designed for making sheets for different
testing i.e. tensile, density, etc.

Features
• Manually operated Hydraulic Press – 20 ton capacity. Two Roll Mill (Lab Model)
• Platen size: 8 x 8 inch. Max. working pressure: 140 kg/cm²
Specifications
• Digital temperature controller for both platens.
• Roll Diameter -150 mm
• Temperature range: 0-300°C.
• Roll Width - 360 mm
• S.S sheet mould (spacer) for moulding of sheets from various plastics material.
• Working Width - 300 mm
• Water cooling facility for both the platens.
• Material Construction: EN 8 hardened material &
• Standard spacer sheet mould of 120 x 120 x 3 mm and 120 x 120 x 4 mm or as per
with high polish chrome plated enable to resist high
the requirement.
temp.
• Reference standard: IS 7328, IS 4984 - 2016.
• HMI touch screen with PLC controller.
20 Ton Compression Moulding Press • Power Requirement: 220/230 V AC, 50 Hz Single Phase.
• NIP gap measurement with 0.01 mm least count.
• Separate temperature controller & display for both
the rolls.
50 Ton Micro-processor Based Compression • Temperature Range: Upto 300°C with PID
controller (Electrically Heated Rolls)
Moulding Press (Lab Model) • Motor Driven Power : 5 HP
• Doctor blade for removal of material on entire
Deepak Hydraulic press is made out • Digital Pressure Indicator & control functions are working width area of the material.
as four-column press, the machine controlled by electrically operated solenoid valves & LCD • A/C Frequency drive for speed control (2 to 22 RPM)
can be used to produce all kinds of based micro-controller. (Controllable from HMI with speed display).
flat samples for Lab Testing • Heating energy is provided by plate heater which are • Paint: Angle Stucture: Epoxy Paint
applications. Working dimensions for arranged to achieve our equal temperature distribution. Body Paint: Powder Coating Semens Grey Shade.
the same are suitable for national & • An integrated water cooling system allows cooling down • Element covered by SS case for protection & long
international standards. samples under pressure. operation.
• Insulating plates are used to reduce heat transfers from • SS rod for manual cutting of the processed polymer.
the press unit. (With SS tray fitted for handling).
Technical Data Unit Value • The motor driven system is equipped with the limit
Working area mm x mm 250 x 250 switch actuated for emergency stop.
Plate dimension mm x mm 300 x 300 (Situated at knee level in front of the machine)
• Power Requirement : 415 V AC, 50 Hz Three Phase +
Daylight opening mm 195
Neutral + Proper earthing is required.
Press force tons (max) 50 • Available in both fix and variable speed model.
Hydraulic pressure bars (max) 150
Working temperature °C (max) 300 Note: Two Roll Mill also available for rubber application
Hydraulic power KW 1.5 with water cooling arrangement.
Two Roll Mill (Lab Model)
Heating power per plate KW 1.5
Machine length L x D x H (mm) 1000 x 550 x 1650
Machine weight Kg 600
50 Ton Micro-processor Based Compression Moulding Press

25 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 26

 Differential Thermal Analyzer (OIT Tester)
•
•
Outstanding repeatability and reproducibility on heating.
High sensitivity for both endothermic and exothermic events.
Milling Contour Cutter Machine (CNC Based)
• Top class design reliable, robust yet extremely sensitive. • High RPM Stapper Based Milling Machine with PC interface. Suitable upto 55 mm thickness
• Easy to use with a new comprehensive software package for control, data samples.
acquisition and processing. • Special Feature: Templates are not required. Cutting shape / design to be uploaded from PC
system as per various international standards.
Specifications
• For specimen preparation of HDPE/ PVC / PE / ACP samples upto 55mm thickness.
Temperature Range Room Temperature to 400°C
• “X” & “Y” axis stepper driver and ball screw based.
Heating Rate 0.1°C to 30°C/min at 0.1°C intervals • Motor RPM: Upto 3000 RPM.
Cooling Rate Cool rates to ambient within 15 to 20 minutes • Specimen Size: Maximum upto 250 x 250 mm (as per platon size).
Reproducibility 0.5°C with full calibration procedure • Milling Cutter with 4 & 6 cutting flaps for precise cutting.
Accuracy Traceable to NABL standards. • Variable speed control for milling cutter.
Principle Differential temperature measurement • Power Requirement: 220/230 V AC, 50 Hz Single Phase.
(Constant heat flux plate with indents locations for reference
& sample pans)
Differential Thermal Analyzer (OIT Tester) Signal Stable low noise, low temperature drift, solid state amplifier with
appropriate sensitivities
Sensor Differential sensors – ‘E’ Type Control Sensor – PT 100
Atmosphere Separate Gas flow meter to measure the gas flow: Automatic
gas switching accessory with user definable set points Milling Contour Cutter Machine

Motorised “V” Notch Cutter Contour Cutter Machine (Template Type)

for Slow Crack Growth Rate Test
Technical Details
60 Degree Double Equal Angle Cutter Unit • Speed: Based on AC Variable Speed AC Drive. High cutting speed.
‘V’ Notch making machine is used for making the ‘V’ Notch over the pipe surface for slow crack growth • Milling performance & easy operation.
resistance test. • Used for Tensile Test Dumbbell Shape Specimen Preparation.
• Power requirement: 415 V AC, 50 Hz Three Phase + neutral + earthing is required.
Features
• Machine is made in accordance with ASTM F-1474-93 and ISO-13479, IS 14885, IS 4984 - 2016.
• Machine is fully equipped with the digital measurement for length & depth of the notch. Suitable Templates for Contour Cutter
• Control for ‘V’ Notch length is digital and auto reversible. • Template for Die Type - A (180 X 60 mm)
• Notch length measurement with bench travel with accuracy of 0.1 mm. • Template for Die Type - A (180 X 80 mm)
• Control for depth of ‘V’ Notch is manual and measurement is digital. • Template for Die Type - B (250 X 100 mm)
• Notch depth measurement with 0.01 mm accuracy LMPT potentiometer, while making the notch on • Template for Die 150 x 20 mm Type 1
HDPE/MDPE pipe sample. • Template for Die 115 x 25 mm Type 2
• Cutting rate is digitally adjustable. • Template for Die 250 x 100 mm Type 3
• Cutter rotation is having a variable speed drive with AC frequency control & equipped with Panasonic • 63.5 mm Dumbbell shape as per AS TM D 638
motor & inbuilt gear box. • 115 mm Dumbbell shape as per AS TM D 638
• Machine notch bench is suitable up to 280 mm dia pipe & also available for higher diameters, as per • 165 mm Dumbbell shape as per AS TM D 638
requirement of ISO standard. • 245 mm Dumbbell shape as per AS TM D 638
Motorised “V” Notch Cutter • Equipped with front mirror polish acrylic safety cover, for observation during notch making operation. • Rectangular size: 150 x 25 mm, 127 X 13 mm, 80 x 10 mm
Templates Contour Cutter Machine
• Power Requirement: 220/230 V AC, 50 Hz Single Phase.
27 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 28
 Falling Dart Impact Tester for
HDPE, PVC & PPR Pipes / Fabric Material Thermo Cyclic Test Equipment
• REF. ASTM D-2846.
Deepak Free Falling Dart Impact Tester The pipe shall be placed on ‘v’ block in a • Pneumatic operations for lifting and dipping the test specimens.
is used for PVC pipes, PVC ducting pipes such way that one of the marked lines is • 6 Nos. of test specimens can be tested at a time.
& HDPE pipe as per IS, DIN, ASTM, BS, upper most. The stricker shall be allowed to • Maximum specimen size 2 inch. (dia) & maximum length 300 mm.
DOT specifications. fall manually/chain drive motorized system.
• Tank size of hot & cold water bath 900(l) x 600(w) x 400(h) mm.
Specimens: 200 ± 10 mm long pipe shall be
The impact properties of the polymeric cut from the complete section. Each • Pressure to be applied by air compressor or N2 gas bottle.
materials are directly related to the specimen shall be cut clean & gauge to the • Cycle of operation can be programmed in sequence up to 999.9 seconds
overall toughness is defined as the axis of the pipe. for each cycle, & no. of cycles also can be programmed.
ability of the polymer to absorb applied • Construction of Water Baths: Inside SS Body (SS-304).
energy. The area under the stress-strain Features Outside MS Body (Coated MS Sheet).
curve is directly proportional to the • Drop height up to 2 mtrs. • All Hydraulic / Hydro-pneumatic Parts Fitted are made of SS / Brass only.
toughness of a material. Impact strength • Drop height controlled
is a measurement of toughness. The manually/motorised.
higher the impact strength of a material • Pipe diameter can be tested up to 315
the higher the toughness and vice-versa. mm in manual version, where as up to
Impact resistance is the ability of a 450/630 mm in motorised version.
material to resist breaking under a • Falling weight: 250 gms, 500 gms, 1 kg,
Falling Dart Impact Falling Dart Impact
shock loading or the ability to resist the 10 kg or as per the requirement of Falling Dart Impact Tester
Tester Manual Tester Motorised fracture under stress applied at high various standards. With Built- In Pneumatic Cylinder s
speed. IS:15351 – 2008 / IS:7903

U. V. Weather Meter Accelerated Weathering Tester

The damaging effects of sunlight are simulated by fluorescent UV lamps. Exposure temperature is automatically
controlled, as the daily sequence of UV periods and condensation periods. Testing duration of deterioration
effect can be reduce by DWT which may occur in a longer period like a month or years of outdoor exposure.
Deterioration observed includes fading, chalking, cracking, crazing, hazing, blistering, gloss lose, strength lose,
and embitterment.

Specifications
Light source Fluorescent UV-B type lamp with
wavelength of 313 nm.
UV lamps 40 w, 08 nos.
Panel temp. range Ambient to 90°C
Panel temp. accuracy ± 2°C
Water/condensation Ambient to 90°C
U. V. Weather Meter temp. range
Accelerated Weathering Tester
Test capacity Provision of holding 22 specimen of size
Deepak DWT accelerated weathering tester is
75 x 300 mm
a laboratory simulator of the damaging effects
of weather. It is used to predict the relative Test specifications ASTM G 53, ASTM D 4329, ASTM D 5208,
durability of materials exposed to the outdoor ISO 4892 and other relevant
environment. Rain and dew are simulated by a national and international standards.
revolutionary condensation system. Power requirement 220/230 V AC, 50 Hz Single Phase
Thermo Cyclic Test Equipment
29 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 30
 Electrical Conduit Pipes / Casings Impact Test
Testing Application • Twelve samples of conduits, each 200 mm long, shall be subjected to an impact test by means of the
apparatus shown in Fig.
Bending Test Before the rest, the samples shall be conditioned at a temperature of 60±2ºC for 10 days (240 hours).
• Conduits shall be subjected to a bending test. • The test apparatus shall be placed on a pad of sponge rubber 40 mm thick, and this together with
• Reference to the values and to the tests for conduits are made in one relevant conduit specifications the sample, shall be placed in a freezer, the temperature within which is maintained at -5 ±2ºC
taking into account the manufacturer's instructions for bending, so far as they do not contravene the • When the samples have attained the temperature of the air within the freezer or after 2 hours ,
aims of this specification as a whole. whichever is longer period, each sample shall be in turn placed in position on the steel base shown in
Fig. and the hammer is allowed to fall whereby an impact energy £ according to Table is applied. The
Bending Test mass of the hammer and the fall height are also specified in Table.

Compression Test Forces for Impact Test

• Samples of conduit, each 200 mm long, shall be subjected to a compression test using the apparatus
Conduit Impact Energy - Height (£) Mass of the - Kg. Fall - mm
shown in Fig.
Before the test, the outside diameter of the samples shall be measured. The samples shall then be Very light 0.5 0.5 100±1
conditioned at a temperature of 27± 2°C for at least 10 hours. Light 1.0 1.0 100±1
• Immediately after the conclusion of conditioning period, the samples shall be positioned on a flat steel Medium 2.0 2.0 100±1
support and a steel intermediate block as shown in Fig. is placed on the middle of the sample. Heavy 6.0 2.0 300±1
Slowly increasing force as shown in Table for different types of conduits shall then be applied to the Impact Test
Very heavy 20.0 6.8 300±1
intermediate piece within 30 seconds.

Force for Compression Test

Type of Conduit Compression Force (N)
Very light 125
Light 320
Medium 750
Heavy 1250
Very heavy 4000
Compression Test Attachment
for Electrical Conduit Note - The values in the table are subject to modification in relevant conduit specifications.

Piston Gauges For ID Measurement

Million Meg OHM Meter Suitable for 16 mm, 20 mm, 25 mm,
Collapse Test For Insulation Resistance Test 32 mm, 40mm, 50 mm & 63 mm pipe sizes.
• Samples of conduits made of insulating materials of length as specified in Table shall be bent at room
temperature, the bending radius being as given relevant conduit specifications. The samples are then • 10 Meg OHM working capacity.
fixed to a rigid support by means of four straps as shown in Fig. • With suitable electrodes for testing application.

Length of Samples for Collapse Test

H. V. Test Apparatus for
Size (mm) 16 20 25 32 40 50 63
Length (mm) 340 370 450 590 740 900 1130
Electrical Strength Test
• 5 KV at 50 mA working
capacity.
• If mechanical bending aids recommended by the manufacturer are used for rigid conduits, the
• With suitable electrodes for
mechanical aids shall be moved. The support with the sample in position is kept for 24 hours in a
testing application.
heating cabinet at a temperature of 60± 2ºC unless specified otherwise in the relevant conduit
• With digital stop watch for
Cone for Collapse Collapse Test Platform specification. Ring Gauges For OD Measurement “C” Type Gauges for OD Measurement
test duration measurement.
H.V. Tester
31 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 32
 Hydraulic Press for Cone Type
End Plugs Clamping
Features
• Clamping Force: 50 Tons, Maximum.
• Ramp Opening: 1.6 Mtrs. Creep Resistance Tester
• Base size suitable for 315 mm to 800 mm Dia Pipes.
• Clamping Platen Size: 800 X 800 mm. Features
• Maximum Stroke: 600 mm. • With static loads up to 3 kg. With the 0.1 kg Graduation.
• Maximum Clamping Speed: 50 to 150 mm/min. • With environmental system to control the temperature of chamber : From room
• Hydraulic Power Pack with Panel with 3 HP / 3 Phase Motor. temperature to 5°C (cooling) and room temperature to 100°C (heating).
• Vertical Heavy Duty Structure with Base Mounting. • Sample Width : Up to 30 mm.
• Digital display for load and elongation readings.
• Load & Elongation indicator or Control & Display unit.
• Digital PID based Temperature controller with Autotune facility.
• Heating / cooling “ON” selection toggle switch.
• Weight supporting stand on right side of the machine.
• Weights for difference ranges.
• Load cell on left side of the cover.

Stationery Grip set fitted inside the environmental chamber of the machine.
One is fixed another is free and fix up with the string which is hanged on to the
weight supporter.
Creep Resistance Tester

Hydraulic Press for Cone Type End Plugs Clamping

Emitter Flow Rate Variation

Sieve Analysis Tester Moisture Analyzer Tester as per IS:13487 (For Emitters/Drippers)
The Deepak Emitter Flow Rate Features
Features
• A complete set of Sieve and Shaker. Moisture Analyzer Variation Tester is designed to
determine the mechanical and
• ½ H.P. Motor. Make : Crompton Greaves.
• 28 Stations (seven stations /per pipe).
• Motorized Test Bench Type, Cast Iron Housing
Moisture analyzer is designed for fast and precise functional requirements of irrigation • Digital timer 0 to 99 min. with buzzer system.
Type.
moisture determination of a sample based on mass emitters, and the data to be supplied • Pneumatic/manual funnel stand movement
• With built in timer.
loss during heating process. by the manufacturer to permit correct integrated with timer.
• With complete casting base structure.
installation and operation in the field. • Pressure Gauge Range: 0 to 4.2 kg /cm2
• Power Requirement: 220/230 V AC, 50 Hz
Drying process parameters are set by users on the The apparatus confirms to IS-13487 (02 nos.) With 0.02 Kg/cm2 least count.
Single Phase
basis of law norms , available chemical-physical :1992 standard. • Main line & sub main line pipes made with SS.
data or they are matched experimentally. This test applies to emitters (with or • Water Tank Size: length: 48”, width: 18”, height:
without pressure regulation) intended 12”.
Moisture analyzer is designed to work in Plastic raw for irrigation. This test does not apply • Water tank is made by stainless steel
material industry , Food industry , Construction to emitters which are an integral part 16 gauge sheet.
materials industry , Biotechnology , Pharmacy , of the pipe (during manufacturing as • Power Requirement: 220/230 V AC, 50 Hz
Sieve Analysis Tester Environment protection and others. Main field of use well as micro tubing). Single Phase.
is quality control. • Compressed air line (max. 6 kg/cm2) is
required.
Emitter Flow Rate Variation Tester

33 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 34

 Equipments For Inline Emitting Pipe Testing as per IS:13488 External Co-efficient of Friction Tester
During transportation and storage, friction between the instant it stars to slide, the degree of tilt
products or friction between products and surface often is shown on the Digital Angular display. The
causes irreparable damage. tangent value of that angle is the co-
efficient of friction. Direct digital reading of
Co-efficient of friction is the ratio of frictional force to the co-efficient of friction is also available.
gravitational force acting perpendicular to the two This test is valuable to companies dealing
surfaces of contact. Measurement of frictional properties in plastic packaging.
are made on a pipe, film or sheeting specimen when i.e.
sliding over itself or another substance. Deepak External e.c.o.f = tanǿ
Co-efficient of friction tester employs a Platform covered ǿ = Tilting angle of sample (in degree)
by the pipe under test, which is allowed to slide across the = 23°
platform. The platform is tilted by manually. When it = tan23°
External Co-efficient of Friction Tester reaches a certain angle of tilt the duct starts sliding down = 0.4243

Torsion Tester
Testing Apparatus for Resistance Emitting Pipe Flow Rate Measurement Testing Apparatus for • Reference Standard: 60794 – 1 – 2, IEC : 2003.
to Pullout of Joints Tester Resistance to Tension at • Test Method: E 7: Torsion ( Figure 11 ).
Elevated Temp.
Features Features Features
• With mechanical structure for sample • Testing: suitable for uniformity of emission rate. Features • With set of loads to apply the tension 15 TO 75 N.
hanging. • With digital timer & buzzer system panel. • Hot air circulating oven with • Equipped with cycle counter and programming facility to count four part
• With suitable loads to apply pull-out • Along with all necessary measuring cylinders & mechanical structure for movements as one cycle.
force. calibrated borosil glass measuring cylinder 4 samples hanging. • Speed: Four part movement as one cycle / min.
• As per IS: 13488-2008 standard. (calibrated). • With 180N load. • Servo Controlled 180° Rotation: Clock Wise & Counter Clock Wise. Torsion Tester
• Ref. : IS-13479 standard. • With twenty five emitting discharge test stations. • As per IS: 13488 – 2008 standard. • Duct Clamping: For 3 mm to 50 mm Duct.
• With suitable angel structure to hold • With digital temp. controller, range:
specimens in 5 mtr. Laying length. 0 to 199.9°C, L.c. 0.1°C
• Power Requirement : 220/230 V AC, 50 Hz accuracy ± 1°C
Single Phase. Abrasion Resistance Tester
• Reference Standard: 60794-1-2- IEC: 2003
• Standard Clause No: 6.2.3.2 Method 2
• Test Method: E 2B Abrasion Resistance of Optical Fibre Cable Markings (Suitable for
Microduct / Microduct Bunch - Bundle)
Traveling Microscope
• S u i t a b l e fo r t h i c k n e s s Features
measurement/flow path • No. of Cycles: Selectable
measurement. • Cycle Speed: 100 Cycles /min ± 5
(For distance measurement Go Not Go Gauges • Applied Force : 4 N to 6 N Loads
between ribs of emitters, Suitable for 12, 16, 20 & 25 mm emitting pipes. • Equipped with programmable cyclic counter for counting the cycles and for auto stop
fitted in inline emitting pipes, (For inside diameter of inline emitting pipes, as per after programmed cycle
as per IS-13488 standard). IS-13488 Standard). • Motorized travel facility for 100 mm length stroke
Abrasion Resistance Tester • Available specimen clamping jaws: suitable for 3 mm to 50 mm duct

35 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 36

 Torque Rheometer & Mixers
with Single Screw Extrusion Attachments
The Fusion Gram is the universal Torque Rheometer for application
of investigations or processing behavior in laboratories and
simulations with a torque measuring range of 200 NM and speed
range from 2 to 100 RPM. The Fusion Gram is the perfect basic unit
for practice oriented measurements with Mixers, Single Screw.

Extruders for:
• Raw Material and Recipe Development.
• Material Testing.
• Quality Control Parallel to Production.
• Optimization of Production Process.
Measuring Extruders
• Laboratory Scale Production of Samples for Further Investigations.
The Fusion Gram with its Extruder Measuring Heads of
19 mm Series, various Screw Geometries, Die Head, and
Down Stream Equipment for Raw Material Control and
Product Development.
The measuring principle is based on making visible the resistance created by the
The Material is Plasticised in lab oriented way and Extruded sample material against the Rotors and corresponding Torque measured and graph is
through the Measuring Extruder. plotted and recorded (Torque and temperature v/s time) for each sample material.

All the measuring values like Torque, Melt Temperature, The graph describe the relationship between Torque(viscosity) and temperature/time
Melt Pressure are recorded continuously and displayed in with reference of structural changes of the material.
the form of table and graph during the test and after the
completion of the test.

Additionally Rheometric capillary die head for continuous

viscosity measurement.

The Output also provides all data for the Rheological

calculations.
Measuring Mixers for Laboratory
Fusion Behavior
Heat & Shear Stability
Cross Linking Reaction
Flow & Cure Behavior & Many More

The Deepak Measuring Mixers for Testing the Processibility of

Thermodynamics, Fillers, Pigments, other Plastic and Plastifiable Materials.

Highlights of Deepak Measuring Mixers:

• For Easy Handling and Cleaning
• Electric Heating
• Precise and Constant Temperature Conditioning up to 300°C
• Flexible Reports

37 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 38

 Test Equipment for Apparent Initial DRS 50 Ring Stiffness Tester
Circumferential Tensile Strength Test Application DEEPAK is pleased to offer the DRS-50, the stiffness friendly Windows XP/7/8.1 based software system. This
tester with ring lifting system for addressing safety software system allows standalone machine operation and
“Deepak” has great pleasure in introducing to RS-232 connectivity with PC interfacing hazards in handling large pipe diameter stiffness test result display in the event of computer system failure
you the DPPL-Split-1000 Machine along with The DPPL-split-1000 is equipped with a RS-232 interfacing specimens. For pipes up to 2600 mm, stiffness or PC–Machine communication failure. And statistical data
computer interfacing facility. The same is software system, which offers PC monitoring, Control and specimen weight' exceeds 100 Kg necessitating more analysis also can be done for all the recorded test data.
capable of testing pipes of DN 250 to DN 3000 Measurement System. The same is based on user friendly than one operator for handling specimen during loading Variable Speed Control -
in accordance with requirements of ISO 8521 windows-xp based software system. This software system allows and testing. Suitable for stiffness of 3 mtr. dia pipes.
method B. ASTM D 2290. BS EN 1394. In
Conformance to Test Standards Requirements
standalone machine operation and test result display in the Precise LCD display panel unit
addition to meeting requirements of above event of computer system failure or PC–Machine The DRS-50 is equipped with AC servo speed control
standard, particularly as regards groove depth communication failure. Software is equipped with the statistical DRS-50 is having an ultra precision measurement system, allowing conformance to requirements of ISO
(specimen width), test speeds (time to failure), data analysis for the recorded data. system based LCD display for force readings . This is to 5893, and Class 0.5 of EN 10002-2 and ISO 7500/1 for pipe
stroke, the DPPL-Split-1000 includes following enable testing pipe sections as per ISO 5893, and Class sized ON 250 to DN 2800.
Variable Speed Control - 0.5 of EN 10002-2 and ISO 7500/1. Force accuracy of
additional features: Other Accessories (For safety and user-friendliness)
Conformance to Test Standards Requirements 0.5% is achieved between full-scale of the machine
Precise LCD display panel unit The DRS-50 is supplied with a number of accessories as below:
The DPPL-split-1000 is equipped with two hydraulic cylinders down to 1% of full-scale (range required by standards:
An ultra precision measurement system based and speed control with digital flow control valve, allowing • Power Assisted Safety covers.
from full-scale to 20% of full-scale). The 1% accuracy
LCD display for force readings. This is to enable conformance to requirements of ISO 8521, ASTM D 2290 and requirement of ASTM E4 will extend from full-scale to • Standard tool kit.
testing pipe sections ranging from DN 250 to BS 5480 for pipe sized ON 250 to DN 3000. 0.2% of full-scale: for the DRS-50 this corresponds to a • Master software CD.
DN 3000. the display unit performance is Other Accessories - for safety and user-friendliness range from 6.5 Tons down to 15 Kg. • Interfacing connectivity cable RS 232/USB Port.
based on ultra-precision low profile load cells The DPPL-split-1000 is supplied with a number of accessories RS-232 connectivity with PC interfacing
enable to fulfill the requirements of relevant including:
testing standards. This is especially important The DRS-50 is equipped with a RS-232 interfacing
to enable testing pipe sections ranging from • Power Assisted Safety covers •Standard tool kit software system, which offers PC monitoring, Control
DN 250 to DN 3000. • Master software CD •Interfacing Connectivity Cable and Measurement System. The same is based on user
DRS 50 Ring Stiffness Tester

Test Station for GRP Couplers with Hydraulic Clamping

• Six Jaw Clamping System with six Hydraulic System • Male rings for upper plate & bottom plate along
UTM DTRX 250 KN
Operated Jaws, from top side. with the sealing rubber ring, are provided for all DEEPAK is pleased to offer the UTM-DTRX-250 KN, the tensile Variable Speed Control -
• Ejector System for each size of GRP Coupler, fixed with one the coupler sizes, as given below. tester with addressing safety features for high thickness & Conformance to Test Standards Requirements
hydraulic cylinder from bottom side. • Sizes are: high load operated samples. The UTM-DTRX-250KN is equipped with AC frequency
• Sliding Trolley System for inserting & removing the GRP Coupler 300, 350, 400, 450, 500, 600, 700, 800, 900, Precise LCD display panel unit variable speed control system, allowing conformance
from left side of the equipment. 1000, 1100, 1200, 1300, 1400, 1500, UTM-DTRX-250KN is having an ultra precision measurement to requirements of ASTM D 638 & BS 2782 standards.
• Three differnet types of assemblies for fixing the GRP 1600, 1700, 1800, 1900, 2000, 2100, 2200, system based LCD display for force & elongation readings . Other Accessories
Couplers, suitable for ring diameter from 300 mm to 2300, 2400, 2500 & 2600. This is to enable testing specimens as per ASTM D 638, (For safety and user-friendliness)
500 mm, with height of 270 mm & for ring diameter above • All functions like lifting the upper plate, BS 2782 standards. Force accuracy of 0.5% is achieved The UTM DTRX 250KN is supplied with a number of
500 mm, with height of 330 mm. movement of six clamping jaws, ejection of between full-scale of the machine down to 1% of full-scale accessories as below:
• For rings of 350 and 450 mm, special plates and ejector specimen ring are driven by hydraulic cylinders. (range required by standards: from full-scale to 20% of full-
rings are provided. • Power Assisted Safety covers.
[Total 8 Nos. Hydraulic Cylinders are scale).
• For rings of 300, 400 and 500 mm, the distance boxes are provided for all the operations] • Standard tool kit.
RS-232 connectivity with PC interfacing
provided. • Power pack & control panel • Master software CD.
UTM-DTRX-250KN is equipped with a RS-232 interfacing
• To keep the ring on bottom plate while lifting the upper for all hydraulic cylinders software system, which offers PC monitoring, Control and • Interfacing connectivity cable RS-232/USB Port.
plate by Hydraulic Cylinder, additional different type of [operations]. Measurement System. The same is based on user friendly
hooks are provided for diameter & 450 mm for rest of the • High pressure piping from Windows XP/7/8.1 based software system. This software
rings, hooks will be same. power pack to all hydraulic Hydro-static Pressure Testing Equipment system allows standalone machine operation and test result
• To eject the ring from bottom plate after lifting the upper cylinders, is provided. for GRP Couplers (Dia: 300 to 2600 mm) display in the event of computer system failure or
plate, ejectors pins are provided below the bottom plate, PC–Machine communication failure.
for safe operation. UTM DTRX 250 KN
39 www.deepakpolyplast.in Deepak Poly Plast Pvt. Ltd. 40
 quality certification
41 www.deepakpolyplast.in
solutions for quality control
and evaluations An ISO 9001-2008 Company
 Regd. Office
405, Sur Mount, 4th Floor, S. G. Road,
Opp. Iskon Temple, Ahmedabad - 380015 (Guj.) INDIA
Telefax: +91-79-26860342, 26861101, 26860431

Works

www.brandaid.in
Plot No. 198/1-2, Near Deep Kiran Food Products,
Industrial Estate, Dantali - 382721, via Lapkaman Village,
Gota Vadsar Road, Tal. Kalol, Dist. Gandhinagar (N. Guj.) INDIA
Tel: +91-7622020009

E-mail: [email protected] | [email protected]

[email protected] | [email protected]
[email protected] | [email protected]

An ISO 9001-2008 Company www.deepakpolyplast.in | www.deepakpolyplast.com