Scribd
Upload
257 views2 pages

LTE Idle Mode - Cell Reselection: Measurements Condition: Specifies When To Start Measuring Neighboring Cells. Once

1) LTE idle mode cell reselection involves measuring neighboring cells and reselecting to a new candidate cell based on certain criteria. 2) There are two mechanisms for cell reselection - legacy based and priority based. Legacy based uses a cell ranking system for intra-frequency and equal priority inter-frequency reselection. Priority based uses priority values between 0-7 for inter-frequencies and inter-RAT frequencies. 3) The UE performs measurements on intra-frequency, inter-frequency, and inter-RAT cells based on signal level thresholds. For reselection, it compares the serving cell to neighboring cells based on their relative rankings and priority levels.

Uploaded by

vikram singh rathore
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
257 views2 pages

LTE Idle Mode - Cell Reselection: Measurements Condition: Specifies When To Start Measuring Neighboring Cells. Once

1) LTE idle mode cell reselection involves measuring neighboring cells and reselecting to a new candidate cell based on certain criteria. 2) There are two mechanisms for cell reselection - legacy based and priority based. Legacy based uses a cell ranking system for intra-frequency and equal priority inter-frequency reselection. Priority based uses priority values between 0-7 for inter-frequencies and inter-RAT frequencies. 3) The UE performs measurements on intra-frequency, inter-frequency, and inter-RAT cells based on signal level thresholds. For reselection, it compares the serving cell to neighboring cells based on their relative rankings and priority levels.

Uploaded by

vikram singh rathore
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

LTE Idle Mode – Cell Reselection

After cell selection UE performs measurement and carry out cell reselection of new
candidate cell. This is based on certain criterion. Reselection process involves 2 steps:

Measurements Condition: Specifies when to start measuring neighboring cells. Once


condition is met UE measures the RSRP level of the E-UTRA cells on the current frequency
and any inter-frequency and inter-RAT frequency carriers.

Reselection Condition: Specifies reselection criteria for candidate cell. There are two
different mechanisms for cell reselection:

1) Legacy Based
2) Priority Based
3) Cell reselection can be either Legacy or Priority based

Legacy Based
This is classical Ranking based system and is applied to intra-frequency reselection.

• It is also applied to inter frequencies which are equally prioritized.

• UE applies cell ranking R criterion on serving cell and neighboring cell.

Priority Based
Priority values in the range [0...7] are used, where 0 indicates lowest priority and 7
indicates highest priority.

Priorities can be set for:

Inter Frequencies: Lower, Equal or Higher Priority


Inter-Rat Frequencies: Higher or Lower Priority

NOTE: Equal priorities between different RATs are not supported

Measurement Performed by UE:

1) Measurement on Intra Freq cells are performed if serving cell

Srxlev ≤ SIntraSearchP or Squal ≤ SIntraSearchQ

2) Measurements on E-UTRA cells on inter-frequency carriers and cells on inter-RAT


frequencies with higher cell reselection priority than the current frequency are always
performed.

3) Measurements on E-UTRA cells on inter-frequency carriers and cells on inter-RAT


frequencies with equal or lower cell reselection priority than the current frequency
are performed if serving cell

Srxlev ≤ SNonIntraSearchP or Squal ≤ SNonIntraSearchQ


Reselection Condition:

1) Legacy Based (Intra Freq+ equal Priority Inter Freq) Cell Reselection:

UE applies cell ranking R criterion on serving cell and neighboring cell.

Rs = Qmeas, s + Qhyst (serving Cell ranking)

Rn = Qmeas, n - QOffset (Neighbor Cell ranking)

Qhyst is a hysteresis value preventing too-frequent reselection back and forth between cells
of nearly equal rank.

QOffset is an offset in the cell ranking criterion of neighbor E-UTRA cells. It consists of a cell
individual part and a frequency specific part. The frequency specific part applies to equal
priority inter-frequency cells only.

qOffsetCellEUtran: Cell individual offset in the intra-frequency and equal priority inter-
frequency cell ranking criteria.

qOffsetFreq: Frequency specific offset in the equal priority inter-frequency cell ranking
criteria.

When a neighbor cell is ranked as better than the serving cell (Rn > Rs) during a time
interval TreselectionEUTRA, the UE performs a cell reselection to the better-ranked cell.

2) Priority-Based Cell Reselection:

Note: The UE only perform cell reselection evaluation for the E-UTRA and inter-RAT
frequencies that are given in system information and for which a cell reselection priority is
provided.

Case 1: If the UE finds an inter-frequency carrier or an inter-RAT frequency with a cell


reselection priority higher than the frequency where the UE is camping, the UE
attempts to reselect a cell on that frequency. Cell reselection will occur if

Srxlev (Target Cell) > threshXHigh or Squal (Target Cell) > threshXHighQ

Where Srxlev and Squal represents cell selection criterion.

Srxlev = Qrxlevmeas - Qrxlevmin and Squal = Qqualmeas - Qqualmin

Case 2: if Srxlev (serving cell) < threshServingLow or Squal (serving Cell) < threshServingLowQ

The UE attempts to reselect a cell on an inter-frequency carrier or an inter-RAT frequency


with cell reselection priority lower than the frequency where the UE is camping and
reselection will occur if

Srxlev (Target Cell) > threshXLow or Squal (Target Cell) > threshXLowQ

You might also like