Century Star Milling CNC System

Programming Guide

V3.3
December,, 2007
December

Wuhan Huazhong Numerical Control Co., Ltd

©2007 Wuhan Huazhong Numerical Control Co., Ltd

 Preface

Preface
Organization of documentation
1. General
2. Preparatory Function
3. Interpolation Function
4. Feed Function
5. Coordinate System
6. Spindle Speed Function
7. Tool Function
8. Miscellaneous Function
9. Functions to Simplify Programming
10. Comprehensive Programming Example
11. Custom Macro

Applicability
This Programming Guide is applicable to the following CNC system:
HNC-18iM/19iM v4.0
HNC-18xp/M
HNC-19xp/M
HNC-21MD/22MD v05.62.07.10

Internet Address
http://www.huazhongcnc.com/

i
 Table of Contents

Table of Contents
Preface............................................................................................................................................. i
1 General................................................................................................................................... 1
1.1 CNC Programming..................................................................................................... 2
1.2 Interpolation................................................................................................................4
1.2.1 Linear Interpolation........................................................................................ 4
1.2.2 Circular Interpolation......................................................................................4
1.2.3 Helical Interpolation....................................................................................... 5
1.3 Feed Function............................................................................................................. 6
1.4 Coordinate System......................................................................................................7
1.4.1 Reference Point...............................................................................................7
1.4.2 Machine Coordinate System...........................................................................8
1.4.3 Workpiece Coordinate System........................................................................9
1.4.4 Setting Two Coordinate Systems at the Same Position................................ 10
1.4.5 Absolute Commands.....................................................................................11
1.4.6 Incremental Commands................................................................................ 12
1.4.7 Polar Coordinates..........................................................................................13
1.5 Spindle Speed Function............................................................................................ 14
1.6 Tool Function............................................................................................................15
1.6.1 Tool Selection............................................................................................... 15
1.6.2 Tool Offset.................................................................................................... 15
1.7 Miscellaneous Function............................................................................................ 17
1.8 Program Configuration............................................................................................. 18
1.8.1 Structure of an NC Program......................................................................... 18
1.8.2 Main Program and Subprogram....................................................................19
2 Preparatory Function (G code)............................................................................................. 20
2.1 G code List................................................................................................................21
3 Interpolation Functions.........................................................................................................24
3.1 Positioning (G00)..................................................................................................... 25
3.2 Single Direction Positioning (G60).......................................................................... 26
3.3 Linear Interpolation (G01)........................................................................................27
3.4 Circulation Interpolation (G02, G03)....................................................................... 29
3.5 Helical Interpolation (G02, G03)..............................................................................35
3.6 Virtual Axis (G07) and Sine Interpolation................................................................ 38
3.7 Tapping (G34)...........................................................................................................40
4 Feed Function....................................................................................................................... 43
4.1 Rapid Traverse (G00)............................................................................................... 44
4.2 Cutting Feed (G94, G95).......................................................................................... 45
4.3 Dwell (G04)..............................................................................................................46
4.4 Exact Stop (G09, G61)............................................................................................. 47
4.5 Cutting Mode (G64)................................................................................................. 49
5 Coordinate System................................................................................................................51
5.1 Reference Position Return (G28)..............................................................................52
5.2 Auto Return from Reference Position (G29)............................................................ 53
5.3 Setting a Workpiece Coordinate System (G92)........................................................ 55
5.4 Selecting a Machine Cooridinate System (G53).......................................................56
5.5 Selecting a Workpiece Coordinate System (G54~G59)............................................57
5.6 Plane Selection (G17, G18, G19)............................................................................. 59
5.7 Absolute and Incremental Programming (G90, G91)...............................................60
5.8 Dimension Selection (G20, G21, G22).....................................................................62
ii
 Table of Contents
5.9 Polar Coordinates..................................................................................................... 63
6 Spindle Speed Function........................................................................................................ 66
7 Tool Function........................................................................................................................67
7.1 Tool Selection and Tool Offset (T code)...................................................................68
7.2 Tool Radius Compensation (G40, G41, G42)...........................................................69
7.3 Tool Length Compensation (G43, G44, G49).......................................................... 74
7.4 RTCP (Rotation Tool Center Point Programming)................................................... 76
8 Miscellaneous Function........................................................................................................ 77
8.1 M code List...............................................................................................................78
8.2 CNC M-Function...................................................................................................... 79
8.2.1 Program Stop (M00)..................................................................................... 79
8.2.2 Optional Stop (M01).....................................................................................79
8.2.3 End of Program (M02)..................................................................................79
8.2.4 End of Program with return to the beginning of program (M30)................. 79
8.2.5 Subprogram Control (M98, M99).................................................................80
8.3 PLC M Function....................................................................................................... 81
8.3.1 Spindle Control (M03, M04, M05)...............................................................81
8.3.2 Tool Selection (M06).................................................................................... 81
8.3.3 Coolant Control (M07, M08, M09).............................................................. 81
9 Functions to Simplify Programming.................................................................................... 82
9.1 Mirror Image (G24, G25)......................................................................................... 83
9.2 Scaling (G50, G51)...................................................................................................85
9.3 Coordinate System Rotation (G68, G69)..................................................................87
9.4 Canned Cycles.......................................................................................................... 89
9.4.1 Return to the Initial Point/R point Level (G98, G99)................................... 90
9.4.2 High-speed Peck Drilling Cycle (G73).........................................................91
9.4.3 Left-hand Tapping Cycle (G74)....................................................................93
9.4.4 Fine Boring Cycle (G76).............................................................................. 95
9.4.5 Drilling Cycle, Spot Drilling (G81).............................................................. 97
9.4.6 Drilling Cycle, Counter Boring Cycle (G82)................................................99
9.4.7 Peck Drilling Cycle (G83).......................................................................... 101
9.4.8 Tapping Cycle (G84).................................................................................. 103
9.4.9 Boring Cycle (G85).................................................................................... 105
9.4.10 Boring Cycle (G86).................................................................................... 107
9.4.11 Back Boring Cycle (G87)........................................................................... 109
9.4.12 Manual Boring Cycle (G88)........................................................................111
9.4.13 Boring Cycle (G89).....................................................................................113
9.4.14 Canned Cycle Cancel (G80)....................................................................... 114
9.5 Summary.................................................................................................................115
10 Custom Macro............................................................................................................ 121
10.1 Variables................................................................................................................. 122
10.1.1 Type of Variables........................................................................................ 122
10.1.2 System Variables........................................................................................ 123
10.2 Constant.................................................................................................................. 130
10.3 Operators and Expression....................................................................................... 131
10.4 Assignment............................................................................................................. 132
10.5 Selection statement IF, ELSE,ENDIF.....................................................................133
10.6 Repetition Statement WHILE, ENDW................................................................... 134
10.7 Macro Call.............................................................................................................. 135
10.8 Example.................................................................................................................. 137

iii
 1. General

1 General
This chapter is to introduce the basic concepts in Computerized Numerical Control (CNC)
system: HNC-21M/22M, HNC-18iM/19iM, HNC-18xp/M, HNC-19xp/M.

1
 1. General

1.1 CNC Programming

To operate CNC machine tool, the first step is to understand the part drawing and produce a
program manual script. The procedure for machining a part is as follows (Figure 1.1):
1) Read drawing
2) Produce the program manual script
3) Input the program manual script by using the machine control panel
4) Manufacture a part

2
 1. General

1. Reading drawing

1
8
A 6 8
R
B 7
1
10
0
0
2. Programming

%3308 (the origin is on A)

N1 G92 X0 Y0 Z50
N2 M03 S500
N3 G00 X-31 Y-26
N4 Z5
N5 G01 Z-3 F40
….

3. Inputting program

4. Manufacturing

Workpiece

Figure 1.1 The workflow of operation of CNC machine tool

3
 1. General

1.2 Interpolation
Interpolation refers to an operation in which the machine tool moves along the workpiece
parts. There are five methods of interpolation: linear, circular, helical, parabolic, and cubic.
Most CNC machine can provide linear interpolation and circular interpolation. The other
three methods of interpolation (helical, parabolic, and cubic interpolation) are usually used
to manufacture the complex shapes, such as aerospace parts.

1.2.1 Linear Interpolation

Linear interpolation refers to the tool movement along a straight line.

tool

workpiece

Figure 1.2 Linear Interpolation

1.2.2 Circular Interpolation

Figure 1.3 shows a tool movement along an arc.

tool

workpiece

Figure 1.3 Circular Interpolation

Note:
In this manual, it is assumed that tools are moved against workpieces.

4
 1. General

1.2.3 Helical Interpolation

Helical interpolation can be used to manufacture threads on a workpiece.

Figure 1.4 Helical Interpolation

5
 1. General

1.3 Feed Function

- Feed refers to an operation in which the tool moves at a specified speed to cut a
workpiece.
- Feedrate refers to a specified speed, and numeric is used to specified the feedrate.
- Feed function refers to an operation to control the feedrate.
mm/min

Tool
F

workpiece

Table

Figure 1.5 Feed Function

For example:
F150.0 //feed the tool at 150mm/min, while the workpiece makes one turn

6
 1. General

1.4 Coordinate System

1.4.1 Reference Point
Reference point is a fixed position on CNC machine tool, which is determined by cams and
measuring system. Generally, it is used when the tool is required to exchange or the
coordinate system is required to set.
Reference Position

Tool

workpiece

Table

Figure 1.6 Reference Point

There are two ways to move to the reference point:

- Manual reference position return: The tool is moved to the reference point by operating
the button on the machine control panel. It is only used when the machine is turned on.
- Automatic reference position return: It is used after the manual reference position return
has been used. In this manual, this would be introduced.

7
 1. General

1.4.2 Machine Coordinate System

The coordinate system is set on a CNC machine tool. Figure 1.7 is a machine coordinate
system of milling machine, and shows the direction of axes:
Zm
Ym

M
Xm
Figure 1.7 Machine Coordinate System

In general, three basic linear coordinate axes of motion are X, Y, Z. Moreover, X, Y, Z axis
of rotation is named as A, B, C correspondently. Due to different types of milling machine,
the axis direction can be decided by following the rule – “three finger rule” of the right
hand.

+Y +B + Z＇
+X +Y +Z
+Y
+ X＇
+X
+C +A
+Z +A +B
+Y＇
+C
+X
+Z

Figure 1.8 “three finger rule”

- The thumb points the X axis. X axis controls the cross motion of the cutting tool.
“+X” means that the tool is away from the spindle centerline
- The index points the Y axis. Y axis is usually a virtual axis.
- The middle finger points the Z axis. Z axis controls the motion of the cutting tool.
“+Z” means that the tool is away from the spindle.

8
 1. General

1.4.3 Workpiece Coordinate System

The coordinate system is set on a workpiece. The data in the NC program is from the
workpiece coordinate system.
Z+

Y+
X-

Y- X+

Z-

Figure 1.9 Workpiece Coordinate System

Example: Those three points can be defined on workpiece coordinate system:
P1 corresponds to X20 Y35
P2 corresponds to X50 Y60
P3 corresponds to X70 Y20
Y

P2
P1
60 P3
35
20 X
20
50
70

Figure 1.10 Example of defining points on workpiece coordinate system

9
 1. General

1.4.4 Setting Two Coordinate Systems at the Same Position

When a workpiece is set on the table, the positional relation between machine coordinate
system and workpiece coordinate system are set.
Coordinate system on
Coordinate system
part drawing established
specified by the CNC
on the work-piece
established on the table
Y
Y

workpiece
X
X

Table

Figure 1.11 Setting two coordinate systems at the same position

According to the command program based on the workpiece coordinate system, the tool
moves on the coordinate system specified by CNC, and cuts a workpiece.

10
 1. General

1.4.5 Absolute Commands

The absolute dimension describes a point at “the distance from zero point of the coordinate
system”.

Example: These three point in absolute dimensions are the following:

P1 corresponds to X20 Y35
P2 corresponds to X20 Y60
P3 corresponds to X70 Y20
Y

P2
P1
60 P3
35
20 X
20
50
70

Figure 1.12 Absolute Dimension

11
 1. General

1.4.6 Incremental Commands

The incremental dimension describes a distance from the previous tool position to the next
tool position.

Example: These three point in incremental dimensions are the following:

P1 corresponds to X20 Y35 //with reference to the zero point
P2 corresponds to X30 Y20 //with reference to P1
P3 corresponds to X20 Y-35 //with reference to P2
Y

P2
20 P1
P3
15

20 X
20 30 20

Figure 1.13 Incremental Dimension

12
 1. General

1.4.7 Polar Coordinates

Beside the “Cartesian coordinate system”, another way to specify coordinates is “polar
coordinates”. The polar coordinate method is useful only if there is radius and angle
measurements on a workpiece.

Example: Two points P1 and P2 with reference to the pole are described as follows.
Y
P2

P1
60
75°
100 30°
Pole
30

X
15

Figure 1.14 Polar Coordinates

P1 corresponds to radius=100 plus angle=30°

P2 corresponds to radius=60 plus angle=75°

13
 1. General

1.5 Spindle Speed Function

The cutting speed (v) refers to the speed of the tool with respect to the workpiece when the
workpiece is cut. The unit of the cutting speed is m/min. As for the CNC, the cutting speed
can be specified by the spindle speed (N) in min-1.
Tool
Tool diameter
Spindle speed N
min-1 D mm
V: Cutting speed m/min
workpiece

Table

Figure 1.15 Cutting Speed and Spindle Speed

1000 ∗ v
The formula to get the spindle speed is: N =
πD
N: the spindle speed
v: cutting speed
D: diameter value of the workpiece

Example: When the diameter of workpiece is 100mm, and the cutting speed is 80m/min,
1000 ∗ v 1000 ∗ 80
then the spindle speed: N = = ≈ 250r / m
πD π ∗ 100

The constant surface speed refers to the speed even when the workpiece diameter is changed,
and the CNC changes the spindle speed. At this time, the spindle speed is the cutting speed.

14
 1. General

1.6 Tool Function

1.6.1 Tool Selection
It is necessary to select a suitable tool when drilling, tapping, boring or the like is performed.
As it is shown in Figure 1.16, a number is assigned to each tool. Then this number is used in
the program to specify that the corresponding tool is selected.

Tool number

01

02

Figure 1.16 Tool Selection

1.6.2 Tool Offset

When writing a program, the operator just use the workpiece dimensions according to the
dimensions in the part drawing. The tool nose radius center and the tool length are not taken
into account. However, when machining a workpiece, the tool path is affected by the tool
geometry. There are two kinds of tool offset: tool length compensation and tool radius
compensation.

Length

Radius

Figure 1.17 Length compensation and Radius compensation

15
 1. General
� Tool Length Compensation
There are two kind of ways to specify the value of tool length compensation.
- Absolute value of tool compensation (the distance between tool tip and machine
reference point)
- Incremental value of tool compensation (the distance between tool tip and the
standard tool)

� Tool Radius Compensation

Figure 1.18 shows the difference between the programmed contour and the corrected tool
path.

Programmed contour

Corrected tool path

Figure 1.18 Difference between programmed contour and corrected tool path

16
 1. General

1.7 Miscellaneous Function

Miscellaneous function refers to the operation to control the spindle, feed, and coolant. In
general, it is specified by an M code.

When a move command and M code are specified in the same block, there are two ways to
execute these commands:
1) Pre-M function
M command is executed before the completion of move command
2) Post-M function
M command is executed after the completion of move command.

The sequence of the execution depends on the specification of the machine tool builder.

17
 1. General

1.8 Program Configuration

1.8.1 Structure of an NC Program
As it is shown in Figure 1.19, an NC program consists of a sequence of NC blocks
blocks. Each
block is one of machining steps. Commands in each block are the instruction.
Program

%1000
N01 G91 G00 X50 Y60

N10 G01 X100 Y500 F150 S300 M03

N...... ;COMMENT Program block

N200 M30
Command character

Figure 1.19 Structure of an NC Program

- Format of program name

The program name must be specified in the format OXXXX (X could be letters or
numbers).
- Format of program number
The program number should be started with %XXXX or OXXXX (X could be numbers
only).
- Format of blocks
A block starts with the program block number.
Program block

N.. G.. X…Y… F.. M.. S..

Spindle function
Miscellaneous function
Feed Function
Coordinate - Dimension word
Preparatory function
Program block number

Figure 1.20 Structure of Block

18
 1. General
- Format of end of program
The last block should contain M02 or M03 to indicate the end of program.
- Format of Comments
All information after the “;” is regarded as comments.
All information between “( )” is regarded as comments.

1.8.2 Main Program and Subprogram

There are two type of program: main program and subprogram. The CNC operates
according to the main program. When a execution command of subprogram is at the
execution line of the main program, the subprogram is called. When the execution of
subprogram is finished, the system returns control to the main program.

Main program Subprogram

Instruction 1 Instruction 1

Instruction 2 Instruction 2

Follow the direct ion

of the subprogram

Instruction n

Instruction n+1

Return to the main program

Figure 1.21 Main program and subprogram

Note:
Main program and its subprogram must be written in a same file with a different program
codes.

19
 2. Preparatory Function

2 Preparatory Function (G code)

There are two types of G code: one-shot G code, and modal G code.
Table 2 1 Type of G code
Type Meaning

One-shot G code The G code is only effective in the block in which it is specified

Modal G code The G code is effective until another G code is specified.

Example: G01 and G00 are modal G codes.

N10 G01 X 100;
N20 Y200 X200; G01 is effective from N10 to N30
N30 X300;
N40 G00 Y100;

20
 2. Preparatory Function

2.1 G code List

The following table is the list of G code in HNC system.

Table 2 2 G code list

G code Group function
G00 Rapid positioning
◣G01 Linear interpolation
01
G02 Circular interpolation/Helical interpolation CW
G03 Circular interpolation/Helical interpolation CCW
G04 00 Dwell
G07 00 Virtual axis
G09 00 Exact stop
◣G17 XY plane selection
G18 02 ZX plane selection
G19 YZ plane selection
G20 Input in inches
◣G21 08 Input in metrics
G22 Input in impulses equivalent weight
G24 Programmable mirror image
03
◣G25 Programmable mirror image cancel
G28 Return to reference point
00
G29 Return from reference point
G34 00 Thread tapping
G38 00 Polar Coordinates
◣G40 Cutter compensation cancel
G41 09 Cutter compensation left
G42 Cutter compensation right
G43 Tool length compensation +direction
G44 10 Tool length compensation - direction
◣G49 Tool length compensation cancel
◣G50 Scaling cancel
04
G51 Scaling

21
 2. Preparatory Function
G53 00 Machine coordinate system selection

22
 2. Preparatory Function
G54 Workpiece coordinate system 1
G55 Workpiece coordinate system 2
G56 Workpiece coordinate system 3
11
G57 Workpiece coordinate system 4
G58 Workpiece coordinate system 5
G59 Workpiece coordinate system 6
G60 00 Single direction positioning
◣G61 Exact stop mode
12
G64 Cutting mode
G68 Coordinate rotation
05
◣G69 Coordinate rotation cancel
G73 High-speed drilling cycle
G74 Left-hand tapping cycle
G76 Fine boring cycle
◣G80 Canned cycle cancel
G81 Drilling cycle, Spot drilling
G82 Drilling cycle, Counter boring cycle
G83 06 Peck drilling cycle
G84 Tapping cycle
G85 Boring cycle
G86 Boring cycle
G87 Back boring cycle
G88 Manual Boring cycle
G89 Boring cycle
◣G90 Absolute command
13
G91 Increment command
G92 00 Setting for work coordinate system
◣G94 Feed per minute
14
G95 Feed per rotation
◣G98 Return to initial point in canned cycle
15
G99 Return to R point in canned cycle

23
 2. Preparatory Function
Explanation:
1) G codes in 00 group are one-shot G code, while the other groups are modal G
code.
2) ◣ means that it is default setting.
3) Multiple G codes from different groups can be specified in the same block. If
multiple G codes from the same group are specified in the same block, only the
last G code specified is valid.

24
 3. Interpolation Function

3 Interpolation Functions
This chapter would introduce:

1) Positioning Command (G00)

2) Single Direction Positioning (G60)

3) Linear Interpolation (G01)

4) Circular Interpolation (G02, G03)

5) Helical Interpolation (G02, G03)

6) Thread Tapping (G34)

25
 3. Interpolation Function

3.1 Positioning (G00)

Programming
G00 X_Y_Z_A_

Explanation of the parameters

X, Y, Z, A Coordinate value of the end point in the absolute command or incremental
command

Function
The tool is moved at the highest possible speed (rapid traverse). If the rapid traverse
movement is required to execute simultaneously on several axes, the rapid traverse speed is
decided by the axis which takes the most time. Thus, the tool path is nonlinear. The operator
can use this function to position the tool rapidly, to travel around the workpiece, or to
approach the tool change position.

Example
Move tool from A (20, 15) to B (90, 45) at the rapid traverse speed.
Non linear interpolation
Y positioning
C B

A
15
X
O
20 50 90

Figure 3.1 Positioning (Rapid Traverse)

Absolute programming:
G00 X90 Z45
Incremental programming:
G00 X70 Y30

26
 3. Interpolation Function

3.2 Single Direction Positioning (G60)

Programming
G60 X_ Y_ Z_ A_

Explanation of the parameters

X, Y, Z, A Coordinate value of the end point in the absolute command or incremental
command

Function
At first, move the tool from the start point to the intermediate point at the rapid traverse
speed. Then, tool is moved from the intermediate point to the end point at the specified
feedrate.
Overrun

intermediate point
Start position

Start position

End position Temporary stop

Figure 3.2 Single Direction Positioning (G60)

Note:
The direction and distance from the intermediate point to the end point are set by machine
parameter – single direction positioning offset. When the value of the parameter is less than
0, the direction is negative. When the value of the parameter is more than 0, the direction is
positive.

27
 3. Interpolation Function

3.3 Linear Interpolation (G01)

Programming
G01 X_ Y_ Z_ A_ F_

Explanation of the parameters

X, Y, Z, A Coordinate value of the end point in the absolute command or incremental
command
F Feedrate. It is effective until a new value is specified.

Function
The tool is moved along the straight line at the specified feedrate.

Example 1
Move tool from A (20, 15) to B (90, 45) at the rapid traverse speed.
Y
linear interpolation B
45

A
15
X
O 20 90

Figure 3.3 Linear Interpolation – Example 1

Absolute programming
G01 X90 Y45 F800

Incremental programming
G01 X70 Y30 F800

28
 3. Interpolation Function
Example 2
Use the tool (Φ8) to machine a groove (3mm) on a workpiece.

10

A 60 80

R4

B
15 70
100

Figure 3.4 Linear Interpolation – Example 2

%3308 (the origin is on A) %3309 (the origin is on B)

N1 G92 X0 Y0 Z50 N1 G92 X0 Y0 Z50
N2 M03 S500 N2 M03 S500
N3 G00 X-31 Y-26 N3 G00 X19 Y14
N4 Z5 N4 Z5
N5 G01 Z-3 F40 N5 G01 Z-3 F40
N6 Y26 F100 N6 Y66 F100
N7 X31 N7 X81
N8 Y-26 N8 Y14
N9 X-31 N9 X19
N10 G00 Z50 N10 G00 Z50
N11 X0 Y0 N11 X0 Y0
N12 M05 N12 M05
N13 M30 N13 M30

29
 3. Interpolation Function

3.4 Circulation Interpolation (G02, G03)

Programming
⎧G02⎫ ⎧I_J_ ⎫
G17 ⎨ ⎬X_Y_ ⎨ ⎬F_
⎩G03⎭ ⎩ R_ ⎭
⎧G02⎫ ⎧I_ K_ ⎫
G18 ⎨ ⎬X_ Z_ ⎨ ⎬F_
⎩G03⎭ ⎩ R_ ⎭
⎧G02⎫ ⎧J_ K_ ⎫
G19 ⎨ ⎬Y_ Z_ ⎨ ⎬F_
⎩G03⎭ ⎩ R_ ⎭

Explanation of the parameters

G17 The working plane is XY, and the infeed direction is Z
G18 The working plane is XZ, and the infeed direction is Y
G19 The working plane is YZ, and the infeed direction is X
G02 a circular path in clockwise direction (CW) (Figure 3.5)
G03 a circular path in counterclockwise direction (CCW)
G02 and G03 are defined when the working plane is specified. Figure 3.5 shows the
direction of circular interpolation.
Y X Z
G03 G03
G03
G02 G02 G02

G17 X G18 Z G19 Y

Figure 3.5 Direction of circular interpolation

X, Y/X, Z/Y, Z For an absolute command, the coordinate values of the circle end point in
the specific working plane. For an incremental command, the coordinate values of the
circle end point with reference to the circle starting point in the specific working plane.

30
 3. Interpolation Function
I, J/I, K/J, K Coordinate values of the circle center point with reference to the circle
starting point in incremental command. (Figure 3.6)
End point (X, Y) End point (X, Z) End point (Y, Z)
Y X Z

X 5Z Y

1 Start
point
34 Start
point
2 Start
point
J I K
Centre I Centre K Centre J

Figure 3.6 Distance from the start point to the circle centre point

R Circle radius. When the arc is less than 180° (minor arc), R is positive. If
the arc is more than 180° (major arc), R is negative.
F Feedrate along the circle

Function
The tool is moved along a full circle or arcs.

Note:
1) When it is full circle programming, R can not be used in the program. I, J, K can
only be used in this case.
2) When it is not full circle programming, the operator can select R or I, J, K to
program. If I, J, K, and R addresses are all specified in the program, R takes
precedence and the other are ignored.

31
 3. Interpolation Function
Example 1
Use G02 to program the minor arc a and the major arc b.

b Y

R30
End
a point
a

R30

Start point X
6
Figure 3.7 Circular Interpolation – Example 1

(i) Arc a
G91 G02 X30 Y30 R30 F300
G91 G02 X30 Y30 I30 J0 F300
G90 G02 X0 Y30 R30 F300
G90 G02 X0 Y30 I30 J0 F300

(ii) Arc b
G91 G02 X30 Y30 R-30 F300
G91 G02 X30 Y30 I0 J30 F300
G90 G02 X0 Y30 R-30 F300
G90 G02 X0 Y30 I0 J30 F300

32
 3. Interpolation Function
Example 2
Use G02/G03 to program the full circle.
Y

R30

X
O A

Figure 3.8 Circular Interpolation – Example 2

i）Clockwise circle from A to A

G90 G02 X30 Y0 I-30 J0 F300
G91 G02 X0 Y0 I-30 J0 F300

(ii) Counterclockwise circle from B to B

G90 G03 X0 Y-30 I0 J30 F300
G91 G03 X0 Y0 I0 J30 F300

33
 3. Interpolation Function
Example 3
Use the tool (Φ8) to machine a groove (3mm) on a workpiece.
R10

R10
20

R20 R20

30

Figure 3.9 Circular Interpolation – Example 3

%3314
N1 G92 X0 Y0 Z50
N2 M03 S500
N3 G00 X10 Y30
N4 Z5
N5 G01 Z-3 F40
N6 X30
N7 G02 X38.66 Y25 R10
(N7 G02 X38.66 Y25 J-10)
N8 G01 X47.32 Y10
N9 G02 X30 Y-20 R20
(N9 G02 X30 Y-20 J-10 I-17.32)
N10 G01 X0
N11 G02 X0 Y20 R20
(N11 G02 X0 Y20 J20)
N12 G03 X10 Y30 R10
(N13 G03 X10 Y30 J10)
N14 G00 Z50
N15 X0 Y0
N16 M30
34
 3. Interpolation Function
Example 4
Use the tool (Φ8) to machine a groove (3mm) on a workpiece.
20

R10
R20

Figure 3.10 Circular Interpolation – Example 4

%3315
N1 G92 X0 Y0 Z50
N2 M03 S500
N3 G00 X-25 Y-8.66
N4 Z5
N5 G01 Z-3 F40
N6 G02 X-25 Y8.66 R10
N7 G01 X-10 Y17.32
N8 G02 X-10 Y-17.32 R-20
N9 G01 X-25 Y-8.66
N10 G00 Z50
N11 X0 Y0
N12 M05
N13 M30

3.5 Helical Interpolation (G02, G03)

35
 3. Interpolation Function
Programming
⎧G02⎫ ⎧I_J_ ⎫
G17 ⎨ ⎬X_Y_ ⎨ ⎬Z_F_ L
⎩G03⎭ ⎩ R_ ⎭
⎧G02⎫ ⎧I_K_ ⎫
G18 ⎨ ⎬X_Z_ ⎨ ⎬Y_F_ L
⎩G03⎭ ⎩ R_ ⎭
⎧G02⎫ ⎧J_K_ ⎫
G19 ⎨ ⎬Y_Z_ ⎨ ⎬X_F_ L
⎩G03⎭ ⎩ R_ ⎭

Explanation of the parameters

G17 The working plane is XY, and the infeed direction is Z
G18 The working plane is XZ, and the infeed direction is Y
G19 The working plane is YZ, and the infeed direction is X
G02 a circular path in clockwise direction (CW) (Figure 3.5)
G03 a circular path in counterclockwise direction (CCW)
X, Y/X, Z/Y, Z For an absolute command, the coordinate values of the circle end point in
the specific working plane. For an incremental command, the coordinate values of the
circle end point with reference to the circle starting point in the specific working plane.
I, J/I, K/J, K Coordinate values of the circle center point with reference to the circle
starting point in incremental command.
R Circle radius. When the arc is less than 180° (minor arc), R is positive. If
the arc is more than 180° (major arc), R is negative.
Z, Y, X The coordinate value of the end point with reference to the starting point on
the third axis in the incremental command.
F Feedrate along the circle
L Number of circles on a workpiece

Figure 3.11 Helical Interpolation (G02, G03)

Function
Helical interpolation can be used to manufacture threads on the workpiece.
36
 3. Interpolation Function

Example 1
Use G03 to program.
Z
End point
10

O
30 Y

30
Start point
X
7
Figure 3.12 Helical Interpolation – Example 1
Absolute programming
G90 G17 F300
G03 X0 Y30 R30 Z10

Incremental programming
G91 G17 F300
G03 X-30 Y30 R30 Z10

37
 3. Interpolation Function
Example 2
Use the tool (Φ10mm) to machine a hole (the diameter is 50mm, and the height is 10mm)
on a workpiece.

R25
10

Figure 3.13 Helical Interpolation – Example 2

%3317
N1 G92 X0 Y0 Z30
N2 G01 Z11 X20 F200
N3 G91 G03 I-20 Z-1 L11
N4 G03 I-20
N5 G90 G01 X0
N6 G00 Z30
N7 X30 Y-50
N8 M30

38
 3. Interpolation Function

3.6 Virtual Axis (G07) and Sine Interpolation

Programming
G07 X_Y_Z_A

Explanation of the parameters

X, Y, Z, A One of axes is set as the virtual axis.
If it is set to 0, then that axis is the virtual axis. If it is set to 1, then that axis is the actual
axis.

Function
G07 command can be used with helical interpolation command (G02, G03). The operation
combined G07 and G02/G03 is called sine interpolation.

Note
The tool would not be moved along the virtual axis.

Example 1
Use G03 to program
Y
100

50

Z
O 60

Figure 3.14 Sine Interpolation – Example 1

G90 G00 X-50 Y0 Z0

G07 X0 G91
G03 X0 Y0 I0 J50 Z60 F800

39
 3. Interpolation Function
Example 2
To implement the sine interpolation on the working plane XY.
Z×Z+Y×Y = R×R (R: radius)
Y=R SIN(2π×X/L) (L: the distance on Z axis for each cycle)

Y Y

10
R5
5

Z X
0 5 0

Figure 3.15 Sine Interpolation – Example 2

%3319
N01 G92 X0 Y0 Z0
N02 G07 Z0
N03 G19 G90 G03 Y.0 Z0 J5 K0 X20.0 F100
N04 G07 Z1
N05 M30

40
 3. Interpolation Function

3.7 Tapping (G34)

Programming
G34 K_ F_ P_

Explanation of the parameters

K The distance from the starting point to the bottom of the hole
F Thread lead. If it is positive, the spindle turns clockwise during tapping. If it is negative,
the spindle turns counterclockwise during tapping.
P Dwell time at the bottom of a hole. (The unit is seconds.)

Function
With this command, the operator can rigid tap a thread.

Note
1) When the spindle turns clockwise during tapping, the spindle would turn
counterclockwise during retraction.
2) When the spindle turns counterclockwise during tapping, the spindle would turn
clockwise during retraction.

In general, there is overshoot of the tap at the bottom of the thread during the
spindle-braking portion of the tapping cycle. It can be set by PMC parameters (Table 3-1) to
eliminate the overshoot errors.

41
 3. Interpolation Function
Table 3 1 PMC parameters

CNC system PMC parameters

#0062 Maximum spindle speed during tapping
#0063 Minimum spindle speed during tapping
HNC 18/19i
#0064 Dwell unit for tapping
#0065 Optional dwell unit for tapping
#0017 Maximum spindle speed during tapping
#0018 Minimum spindle speed during tapping
HNC 21/22
#0019 Dwell unit for tapping
#0030 Optional dwell unit for tapping

Optional dwell unit for tapping is only effective when “dwell unit for tapping” is assigned to
“0”. Moreover, it is not necessary to restart the system.

The following formular is to calculate the dwelled unit (X):

D= (S * S / C) * X / 10000 = L * 360 / F
D dwell amount
S spindle speed
C Transmission gear ratio
X dwell unit
L overshoot error
F thread lead

42
 3. Interpolation Function
Example
Use G34 to program.
2-M10×1.5
2-M10×

20
12

20 80

Figure 3.16 Tapping - Example

%0002
G92 X-20 Y-20 Z50
M03 S200
G00 X20 Y12
Z5
G34 K-27 F1.5
G00 X100
G34 K-27 F1.5
G00 Z50
X-20 Y-20
M05
M30

43
 4. Feed Function

4 Feed Function
This chapter would introduce:
1) Rapid Traverse
The tool is moved at the rapid traverse speed set in CNC.
2) Cutting Feed
The tool is moved at the programmed cutting feedrate.
3) Dwell
4) Exact Stop
5) Cutting Mode

44
 4. Feed Function

4.1 Rapid Traverse (G00)

Positioning command (G00) is to move the tool at the rapid traverse speed (the highest
possible speed).

This rapid traverse speed can be controlled by the machine control panel. For more detailed
information, please refer to turning operation manual.

45
 4. Feed Function

4.2 Cutting Feed (G94, G95)

Programming
G94 [F_ ]
G95 [F_ ]

Explanation of the parameters

G94 feedrate per minute.
On linear axis, the unit of feedrate is mm/min, or in/min.
On rational axis, the unit of feedrate is degree/min.

G95 feedrate per revolution

The unit of feedrate is mm/rev, or in/rev.

Note:
1) G94 is the default setting
2) G95 is only used when there is spindle encoder.

Function
The feedrate can be set by G94 or G95.

46
 4. Feed Function

4.3 Dwell (G04)

Programming
G04 P_

Explanation of the parameters

P dwell time (specified in seconds)

Function
It can be used to interrupt machining to get the smooth surface. It can be used to control the
groove cutting, drilling, and turning path.

Example
Use G04 to get the smooth surface.
Z
X
2

Figure 4.1 Dwell – Example

%0004
G92 X0 Y0 Z0
G91 F200 M03 S500
G43 G01 Z-6 H01
G04 P5
G49 G00 Z6 M05 M30

47
 4. Feed Function

4.4 Exact Stop (G09, G61)

Programming
G09
G61

Explanations of the parameters

The tool is moved to the end point of a block, then the position of the end point is checked.
Then, the next block is proceeded.
Y
Position check
(2)

(1)

Figure 4.2 Exact Stop (G09/G61) – tool path from block (1) to block (2)

The difference between G09 and G61 is that G09 is one-shot G code. And G61 is modal G
code.

Function
G09 or G61 can be used to machine a sharp edge.

48
 4. Feed Function
Example
Use G61 to program.
Y

100

30
20
X
50 150

8Figure 4.3 Exact Stop - Example

%0061
G92 X0 Y0 Z0
G91 G00 G43 Z-10 H01
G41 X50 Y20 D01
G01 G61 Y80 F300
X100
…

49
 4. Feed Function

4.5 Cutting Mode (G64)

Programming
G64

Explanation of the parameters

The tool is moved to the end point of a block. Then, the next block is proceeded. The tool
path is shown in the following figure.
Y
(2)

(1)

O X

Figure 4.4 Cutting Mode (G64) – tool path from block (1) to block (2)

Function
G64 command can make the tool move smoothly between two blocks.

50
 4. Feed Function
Example
Use G64 to program.
Y
100

Actual
tool path
30
20
X
50 150

9
Figure 4.5 Cutting Mode – Example

%0064
G92 X0 Y0 Z0
G91 G00 G43 Z-10 H01
G41 X50 Y20 D01
G01 G64 Y80 F300
X100
…

51
 5. Coordinate System

5 Coordinate System
This chapter would introduce:
1) Reference Position Return (G28)
2) Auto Return from Reference Position (G29)
3) Setting a Workpiece Coordinate System (G92)
4) Selecting a Machine Coordinat System (G53)
5) Selecting a Workpiece Coordinate System (G54~G59)
6) Plane Selection (G17, G18, G19)
7) Absolute and Incremental Programming (G90, G91)
8) Dimension Selection (G20, G21, G22)
9) Polar Coordinates (G38)

52
 5. Coordinate System

5.1 Reference Position Return (G28)

Programming
G28 X_ Y_ Z_ A_

Explanation of the parameters

X, Y, Z, A Coordinate values of the intermediate point in absolute command/incremental
command

Function
The tool is moved to the intermediate point rapidly, and then returned to the reference point.
R(Reference position)

B(Intermediate position)

A(Start position for Reference position return)

Figure 5.1 Reference Position Return (G28)

Note:
1) In general, G28 is used to change tools or cancel the mechanical error. Tool radius
compensation and tool length compensation should be cancelled when G28 is
executed.
2) G28 can not only make the tool move to the reference point, but also can save the
intermediate position to be used in G29.
3) When the power is on and manual reference position return is not available, G28 is
same as the maunaul reference position return. The direction of this reference
position return (G28) is set by the axis parameter – reference approach direction.
4) G28 is one-shot G code.

53
 5. Coordinate System

5.2 Auto Return from Reference Position (G29)

Programming
G29 X_ Y_ Z_ A_

Explanation of the parameters

X, Y, Z, A Coordinate value of the end point in absolute command/incremental
command

Function
The tool is moved rapidly from the intermediate point defined in G28 to the end point. Thus,
G29 is generally used after G28 is defined.
R(Reference position)

B(Intermediate position)

C(Destination of return from the reference position)

Figure 5.2 Auto Return from Reference Position (G29)

Note:
G29 is one-shot G code.

54
 5. Coordinate System
Example
Use G28, G29 command to program the track shown in. It moves from the starting point A
to the intermediate point B, and then returns to the reference point R. At last, it moves from
the reference point R to the end point C through the intermediate point B.
R
Y Reference position

B
11
70 Intermediate point
A
50

30 C

X
30 130 180
10
Figure 5.3 Reference Position – Example

…
G91 G28 X100 Y20 ;A→B→R
M06 T02 ;Changing the tool
G29 X50 Y-40 ;R→B→C
…

55
 5. Coordinate System

5.3 Setting a Workpiece Coordinate System (G92)

Programming
G92 X_ Y_ Z_ A_

Explanation of the parameters

X, Y, Z, A Coordinate values of the tool position in the workpiece coordinate system.

Functions
G92 can set a workpiece coordinate system based on the current tool position (X_ Y_ Z_
A_ ).

Example
Use G92 to set a workpiece coordinate system.
Z
20.0

Y
30.0

X 30.0

Figure 5.4 Setting a Workpiece Coordinate System – Example

G92 X30.0 Y30.0 Z20.0

56
 5. Coordinate System

5.4 Selecting a Machine Cooridinate System (G53)

Programming
G53 X_ Y_ Z_ A_

Explanation of the parameters

X, Y, Z, A Absoulte coordinate values of a point in the machine coordinate system.

Function
A machine coordinate system is selected, and the tool moves to the position at the rapid
traverse speed.

Note:
1) Absolute values must be specified in G53. The incremental values would be
ignored by G53.
2) G53 is one-shot G code.

57
 5. Coordinate System

5.5 Selecting a Workpiece Coordinate System

(G54~G59)
Programming
⎧G54⎫
⎪G55⎪
⎪ ⎪
⎪⎪G56⎪⎪
⎨ ⎬ X_ Y_ Z_ A_
⎪ G 57 ⎪
⎪G58⎪
⎪ ⎪
⎪⎩G59⎪⎭
Explanation of the parameters
X, Y, Z, A Coordinate values of the point with reference to the origin of machine in
absolute command

Function
There are six workpiece coordinate system to be selected. If one coordinate system is
selected, the tool is moved to a specified point.

Note:
1) The workpiece coordinate system must be set before using these commands
(G54~G59). The workpiece coordinate system can be set by using the MDI panel.
For detailed information, please refer to the milling operation manual.
2) Reference position must be returned before these commands (G54~G59) are
executed.
3) G54 is the default setting.

58
 5. Coordinate System
Example
Select one of workpiece coordinate system, and the tool path is Current point→A→B.

Origin
-186.327 -117.452 Machine

Y
30 B
Y
40 A
G59
-63.948
G54 O2 30 X
-98.359
O1 30 X

Figure 5.5 Workpiece Coordinate System – Example

%1000
N01 G54 G00 G90 X30 Y40
N02 G59
N03 G00 X30 Y30
N04 G54
N05 X0 Y0
N06 M30

59
 5. Coordinate System

5.6 Plane Selection (G17, G18, G19)

Programming
G17
G18
G19

Explanation of the parameters

G17 working plane is XY, infeed direction is Z
G18 working plane is ZX, infeed direction is Y
G19 working plane is YZ, infeed direction is X

Function
The working plane is specified and used for tool radius compensation and circular
interpolation.

Note:
Move command is not related with the plane selection. For example, in the command G17
G01 Z10, Z axis does still move.

60
 5. Coordinate System

5.7 Absolute and Incremental Programming (G90,

G91)
Programming
G90 X_ Y_ Z_ A_
G91 X_ Y_ Z_ A_

Explanation of the parameters

G90 Absolute programming
X, Y, Z, A Coordinate values of the point with reference to the origin of programming
G91 Incremental programming
X, Y, Z, A Coordinate values of the point with reference to the previous position

Function
The tool is moved to the specified position.

61
 5. Coordinate System
Example
Move the tool from point 1 to point 2 through point 3, and then return to the current point.
Y
45
2

25 3
15 1
X
O 20 40 60

Figure 5.6 Absolute and Incremental Programming – Example

G90 programming
%0001
M03 S500
N01 G92 X0 Y0 Z10
N02 G01 X20 Y15
N03 X40 Y45
N04 X60 Y25
N05 X0 Y0 Z10
N06 M30

G91 programming
%0001
M03 S500
N01 G92 X0 Y0 Z10
N02 G91 G01 X20 Y15
N03 X20 Y30
N04 X20 Y-20
N05 G90 X0 Y0
N06 M30

62
 5. Coordinate System

5.8 Dimension Selection (G20, G21, G22)

Programming
G20
G21
G22

Explanation of the parameters

G20: Inch input
G21: Metric input
G22: Impulses equivalent weight input
The units of linear axis and circular axis are shown in the following table
Table 5 1. Unit of Linear axis and Circular axis
Linear axis Circular axis
Inch system (G20) Inch Degree

Metric system (G21) Mm Degree

Pulse system (G22) Impulses equivalent weight Impulses equivalent weight

Function
Depending on the part drawing, the workpiece geometries can be programmed in metric
measures, inches, or impulses equivalent weight.

63
 5. Coordinate System

5.9 Polar Coordinates

Programming
G38 X_ Y_
G01 AP=_ RP=_
G02/G03 AP=_ RP=_ R_

Explanation of the parameters

G38 Setting a polar coordinate system
X, Y Coordiante value of the pole in the workpiece coordinate system
AP Polar angle
RP Polar radius
R Circle radius

Function
The polar coordinate method is useful only if there is radius and angle measurements on a
workpiece.

Note
These commands can be used with commands of workpiece coordinate system.

64
 5. Coordinate System
Example 1
Use polar coordinates command to program.

R42

50

84

Figure 5.7 Polar Coordinates – Example 1

%3326
G92 X0 Y0 Z10
G00 X-50 Y-60
G00 Z-3
G01 G41 X-42 D01 F1000
Y0
G38 X0 Y0
G02 AP=0 RP=42 R42
G01 Y-50
X-50
G00 G40 Y-60
Z10
G00 X0 Y0
M30

65
 5. Coordinate System
Example 2
When the tool is turning clockwise, the polar radius increases 2mm as the the polar angle
increases 10°.

50

42

Figure 5.8 Polar Coordinate – Example 2

%0001
G54 G00 X-15 Y-15 Z10
G00 Z-3
G01 G41 X0 D01 F1000
Y50
G38 X42 Y50
#0=180
#1=42
while #0 gt 0
G01 AP=[#0] RP=[#1]
#0=#0-10
#1=#1+2
Endw
G01 AP=0 RP=78
Y0
X-15
G00 G40 Y-15
Z10
M30

66
 6. Spindle Speed Function

6 Spindle Speed Function

Spindle function controls the spindle speed (S), the unit of spindle speed is r/min. S is modal
G code command; it is only available when the spindle is adjustable. Spindle speed
programmed by S code can be adjusted by overrides on the machine control panel.

67
 7. Tool Function

7 Tool Function
This chapter would introduce:
1) Too selection and Tool offset (T code)
2) Tool radius compensation (G40, G41, G42)

68
 7. Tool Function

7.1 Tool Selection and Tool Offset (T code)

Programming
T XX XX

Explanation of the parameters

XX Tool number (two digits). The number of tool depends on manufacture’s
configuration.
XX Tool offset number (two digits). It corresponds to the specific compensation value.

Functions
To select the desired tool, T command makes the turret turn, selects a cutter, and calls the
compensation value.

Note:
1) T command is only effective when it is used with tool move command, such as
G00.
2) When T command and tool move command are in the same program block, T
command is executed at first.
3) The same tool can have different compensation values. For example, T0101,
T0102, T0103 are possible.
4) Different tool can have same compensation values. For example, T0101, T0201,
and T0301 are possible.

69
 7. Tool Function

7.2 Tool Radius Compensation (G40, G41, G42)

Programming

⎧G17 ⎫ ⎧G 40⎫
⎪ ⎪⎪ ⎪ ⎧G 00⎫
⎨G18⎬ ⎨G 41⎬ ⎨ ⎬ X _ Y_ Z_ D_
⎪G19 ⎪ ⎪⎩G 42⎪⎭ ⎩ G 01⎭
⎩ ⎭

Explanation of the parameters

G17 Tool radius compensation on plane XY
G18 Tool radius compensation on plane ZX
G19 Tool radius compensation on plane YZ
G40 Deactivate tool radius compensation
G41 Activate tool radius compensation, tool operates in machining operation to the left
of the contour.
G42 Activate tool radius compensation, tool operates in machining operation to the
right of the contour.

cutter’s
rotation cutter’s cutter’s
direction move cutter’s
move
direction rotation
direction
direction

(a) Cutter compensation left (b) Cutter compensation right

Figure 7.1 Tool Radius Compensation

X, Y, Z Coordinate values of the end point. It is the point where the tool radius
compensation is activated or deactivated.
D There are two ways to specify the value of D.
� D01~D99 Each code corresponds to the different values of the tool radius
compensation.
� #100~#199 Variable of radius compensation

70
 7. Tool Function
Function
These commands can control the tool radius compensation to get the equidistant tool paths
for different tools.

Note:
1) G40, G41, and G42 must be used with G00 or G01.
2) Changing the plane of tool radius compensation can only be done when there is no
compensation.

71
 7. Tool Function
Example 1
Use the tool radius compensation, and program for the part shown in Figure 7.2. The dashed
line stands for the actual tool path.
Y
D
30

⑤
④
C
20 E R10
⑥
12
A B ③
15
10

-10
13② 14 X

① 10 30 40

⑦
-10
start point

Figure 7.2 Tool Radius Compensation –Example 1

%3322
G92 X−10 Y−10 Z50
G90 G17
G42 G00 X4 Y10 D01
Z2 M03 S900
G01 Z-10 F800
X30
G03 X40 Y20 I0 J10
G02 X30 Y30 I0 J10
G01 X10 Y20
Y5
G00 Z50 M05
G40 X−10 Y−10
M02

72
 7. Tool Function
Example 2
Use the tool (diameter is Φ8). The depth of cutting is 3mm.
R10

R10
20

R20 R20

30

Figure 7.3 Tool Radius Compensation – Example 2

%3323
N1 G92 X-40 Y50 Z50
N2 M03 S500
N4 G01 Z-3 F400
N5 G01 G41 X5 Y30 D01 F40
N6 X30
N7 G02 X38.66 Y25 R10
(N7 G02 X38.66 Y25 J-10)
N8 G01 X47.32 Y10
N9 G02 X30 Y-20 R20
(N9 G02 X30 Y-20 I-17.32 J-10)
N10 G01 X0
N11 G02 X0 Y20 R20
(N11 G02 X0 Y20 J20)
N12 G03 Y40 R10
(N12 G03 Y40 J10)
N13 G00 G90 G40 X-40 Y50
N14 G00 Z50
N15 M30

73
 7. Tool Function
Example 3
Use the tool (diameter is Φ8). The depth of cutting is 3mm.

R10
60
80

10
15 70
100

Figure 7.4 Tool Radius Compensation – Example 3

%3322 (female die) %3323 (male die)

N1 G92 X-10 Y-10 Z50 N1 #101=4
N2 M03 S500 N2 G92 X-10 Y-10 Z50
N3 Z5 N3 M03 S500
N4 G00 X25 Y20 N4 Z5
N5 G01 Z-3 F40 N5 G01 Z-3 F40
N6 G41 Y30 D01 f100 N6 G41 X15 D101 f100
N7 G03 Y10 R10 N7 Y60
N8 G01 X75 N8 G02 X25 Y70 R10
N9 G03 X85 Y20 R10 N9 G01 X75
N10 G01 Y60 N10 G02 X85 Y60 R10
N11 G03 X75 Y70 R10 N11 G01 Y20
N12 G01 X25 N12 G02 X75 Y10 R10
N13 G03 X15 Y60 R10 N13 G01 X25
N14 G01 Y20 N14 G02 X15 Y20 R10
N15 G03 X23 Y12 R8 N15 G01 Z10
N16 G01 Z10 N16 G00 G40 X0 Y0
N17 G00 G40 X25 Y20 N17 G0 Z50
N18 G0 Z50 N18 M30
N19 M30

74
 7. Tool Function

7.3 Tool Length Compensation (G43, G44, G49)

Programming

⎧G17 ⎫ ⎧G 43⎫
⎪ ⎪ ⎪ ⎪ ⎧G 00⎫
⎨G18⎬ ⎨G 44⎬ ⎨ ⎬ X_Y_Z_H_
⎪G19 ⎪ ⎪G 49⎪ ⎩ G 01⎭
⎩ ⎭ ⎩ ⎭

Explanation of the parameters

G17 XY plane selection (compensate for the difference in tool length along Z axis)
G18 ZX plane selection (compensate for the difference in tool length along Y axis)
G19 YZ plane selection (compensate for the difference in tool length along X axis)
G43 Positive offset
G44 Negative offset
G49 Deactivate the tool length compensation
X, Y, Z Coordinate value of the end point
H H00~H99: Each code corresponds to the different values of the tool length
compensation.

Function
These command can compensate the difference between the assumed tool length in the
programming and the actual tool length.
Tool assumed during Actual tool
programming

Specify this distance as the

value of tool length offset

Figure 7.5 Tool Length Compensation (G43, G44, G49)

75
 7. Tool Function
Example
Use the tool length compensation function to program.

#1

20 #3
⑥

30
Y ⑨
①
#2
13
30
X
120 30 50

Z
length offset
ε = 4mm
X

Tool assumed Actual tool 35 ②

during 12
programming 3
③ ⑤ ⑩ 22
30 18

④ ⑦ ⑧ 11

Figure 7.6 Tool Length Compensation - Example

%1050
G92 X0 Y0 Z0
G91 G00 X120 Y80 M03 S600
G43 Z-32 H01
G01 Z-21 F300
G04 P2
G00 Z21
X30 Y-50
G01 Z-41
G00 Z41
X50 Y30
G01 Z-25
G04 P2
G00 G49 Z57
X-200 Y-60
M05 M30
76
 7. Tool Function

Programming))
7.4 RTCP (Rotation Tool Center Point Programming
RTCP (Rotation Tool Center Point Programming) refers to the auto tool length
compensation when the spatial orientation of the tool changes.

control
point tool length

Tool
center
point programming path

Figure 7.7 Rotation Tool Center Point Programming

G01 (linear interpolation), G00 (rapid positioning), and G02/G03 (circular interpolation) can
be used in the rotation tool center point programming.

G43, G44, G49 can also be used for the tool length compensation.

77
 8. Miscellaneous Function

8 Miscellaneous Function
As it is mentioned in Chapter 1.8, there are two ways of execution when a move command
and M code are specified in the same block.
1) Pre-M function
M command is executed before the completion of move command.
2) Post-M function
M command is executed after the completion of move command

There are two types of M code: one-shot M code, and modal M code.
Table 8 1 Type of M code
Type Meaning

One-shot M code The M code is only effective in the block in which it is specified

Modal M code The M code is effective until another M code is specified.

78
 8. Miscellaneous Function

8.1 M code List

The following is a list of M command.
Table 8 2 M code List

CNC M-function Type of Mode Function Pre/Post-M function

M00 One-shot Program stop Post-M function

M01 One-shot Optional stop Post-M function

M02 One-shot End of program Post-M function

End of program with return to the
M30 One-shot Post-M function
beginning of program
M98 One-shot Calling of subprogram Post-M function

M99 One-shot End of subprogram Post-M function

PLC M-function Type of Mode Function Pre/Post-M function

M03 Modal Spindle forward rotation Pre-M function

M04 Modal Spindle reverse rotation Pre-M function

M05 Modal ◣Spindle stop Post-M function

M06 One-shot Tool Selection Post-M function

M07 Modal Number1 Coolant on Pre-M function

M08 Modal Number2 Coolant on Pre-M function

M09 Modal ◣Coolant off Post-M function

◣: default setting

79
 8. Miscellaneous Function

8.2 CNC M-Function

8.2.1 Program Stop (M00)
M00 is one-shot M function, and it is post-M function.
The program can be stopped, so that the operator could measure the tool and the part, adjust
part and change speed manually, and so on.
When the program is stopped, the spindle is stopped and the coolant is off. All of the current
modal information remains unchanged. Resuming program could be executed by pushing
“Cycle Run” button on the machine control panel.

8.2.2 Optional Stop (M01)

M01 is one-shot M function, and it is post-M function.
Similarly to M00, M01 can also stop the program. All of the modal information is
maintained. The difference between M00 and M01 is that the operator must press M01

button ( ) on the machine control panel. Otherwise, the program would not be stopped
even if there is M01 code in the program.

8.2.3 End of Program (M02)

M02 is one-shot M function, and it is post-M function.
When M02 is executed, spindle, feed and coolant are all stopped. It is usually at the end of
the last program block. To restart the program, press “Cycle Run” button on the operational
panel.

8.2.4 End of Program with return to the beginning of program

(M30)
M30 is one-shot M function, and it is post-M function.
Similarly to M02, M30 can also stop the program. The difference is that M30 returns control
to the beginning of program. To restart the program, press “Cycle Run” button on the
operational panel.

80
 8. Miscellaneous Function

8.2.5 Subprogram Control (M98, M99)

� End of Subprogram (M99)
M99 indicates the end of subprogram and returns control to the main program. It is one-shot
M function, and it is post-M function.

� Calling a Subprogram (M98)

M98 P_ L_
P program number of the subprogram
L repeated times of subprogram

M98 is used to call a subprogram. It is one-shot M function. Moreover, it is post-M

function.

81
 8. Miscellaneous Function

8.3 PLC M Function

8.3.1 Spindle Control (M03, M04, M05)
M03 starts spindle to rotate CW at the set speed set in the program.
M04 starts spindle to rotate CCW at the set speed in the program.
M05 stops spindle.
M03, M04 are modal M code, and they are pre-M function. M05 is modal M code, and it is
post-M function. M05 is the default setting.

8.3.2 Tool Selection (M06)

M06 can select a desired tool to set on the spindle.
For example, M06 T01; the tool No.01 is selected.
M06 is one-shot M code, and it is post-M function.

8.3.3 Coolant Control (M07, M08, M09)

M07, M08 can turn on the coolant.
M09 can turn off the coolant.
M07 and M08 are modal M code, and they are pre-M function. M09 is one-shot M code,
and it is post-M function. Moreover, M09 is the default setting.

82
 9. Functions to Simplify Programming

9 Functions to Simplify Programming

This chapter would introduce:
1) Mirror Image (G24, G25)
2) Scaling (G50, G51)
3) Coordinate System Rotation (G68, G69)
4) Canned Cycle

83
 9. Functions to Simplify Programming

9.1 Mirror Image (G24, G25)

Programming
G24 X_ Y_ Z_ A_
M98 P_
G25 X_ Y_ Z_ A_

Explanation the parameters

G24 Activate a mirror image
X, Y, Z, A Position and axis of symmetry for producing a mirror image
M98 P_ The sequence number of subprogram for producing a image on a part
G25 Deactivate a mirror image
X, Y, Z, A Axis of symmetry for producing a mirror image

Function
These commands can be used to mirror workpiece shapes on coordinate axes.

Mirror X Y

X
Mirror Y

Figure 9.1 Mirror Image

Note
When there is only one axis of symmetry, the movement of tool for the mirror image is
opposite to the tool movement of origin image.

84
 9. Functions to Simplify Programming
Example
Use the mirror image function to machine a workpiece. The distance from the tool tip to the
workpiece is 100mm. The depth of cutting is 5mm.
Y
30 R10

② ①
10
X
-30 -10 10 30

-10
③ ④

-30

Figure 9.2 Mirror Image - Example

%0024 ; Main program

G92 X0 Y0 Z0
G91 G17 M03 S600
M98 P100 ; Machining part ①
G24 X0 ; The symmetry axis is Y-axis.
; The position of symmetry is X=0
M98 P100 ; Machining part ②
G24 Y0 ; The symmetry axes are X-axis and Y-axis.
; The position of symmetry is (0, 0)
M98 P100 ; Machining part ③
G25 X0 ; The symmetry Y-axis is cancelled.
; X-axis is still valid
M98 P100 ; Machining part ④
G25 X0 Y0 ; Mirror image is cancelled
M30
%100 ; Subprogram (①)
N100 G41 G00 X10 Y4 D01
N120 G43 Z−98 H01
N130 G01 Z−7 F300
N140 Y26
N150 X10
N160 G03 X10 Y−10 I10 J0
N170 G01 Y−10
N180 X−25
N185 G49 G00 Z105
N200 G40 X−5 Y−10
N210 M99
85
 9. Functions to Simplify Programming

86
 9. Functions to Simplify Programming

9.2 Scaling (G50, G51)

Programming
G51 X_Y_ Z_ P_
M98 P_
G50

Explanation of the parameters

G51 Activate the scaling
X, Y, Z, Coordinate value of scaling center point in absolute command
P Scaling magnification
M98 P_ The sequence number of subprogram for produce a shape on a part.
G50 Deactivate the scaling

Function
This command enables the size of a shape to be changed.

Figure 9.3 Scaling

Note
Scaling is not applicable to the tool compensation. When the operator use the tool
compensation function in the program, the machine would execute the scaling before
calculating the tool offset value.

87
 9. Functions to Simplify Programming
Example
Use the scaling function to scale down a triangular ΔABC to ΔA’B’C’. The center point of
scaling is D point (50, 50). The scaling magnification is 0.5. The starting point of tool is
50mm away from the workpiece.
C(50, 110)
Y

16 C’

D
A’ B’
B (90, 30)
A(10, 30)
X
Z
10
6
16.2 X
16.1
Figure 9.4 Scaling – Example

%0051 ;Main program

G92 X0 Y0 Z60
G91 G17 M03 S600 F300
G43 G00 X50 Y50 Z-46 H01
#51=14
M98 P100 ;Machining ΔABC
#51=8
G51 X50 Y50 P0.5 ;Scaling center(50,50)
;Scaling magnification 0.5
M98 P100 ;machining ΔA’B’C’
G50 ;Scaling cancel
G49 Z46
M05 M30

%100 ;Subprogram(ΔABC)
N100 G42 G00 X-44 Y-20 D01
N120 Z[-#51]
N150 G01 X84
N160 X-40 Y80
N170 X−44 Y-88
N180 Z[#51]
N200 G40 G00 X44 Y28
N210 M99

88
 9. Functions to Simplify Programming

9.3 Coordinate System Rotation (G68, G69)

Programming
G17 G68 X_ Y_ P_
G18 G68 X_ Z_ P_
G19 G68 Y_ Z_ P_
M98 P_
G69

Explanation of the parameters

G17,G18, G19 One of planes (XY/ZX/YZ) is selected to be rotated.
G68 Activate the coordinate system rotation.
X, Y/X, Z/Y, Z Coordinate value of the center point of rotation
P Angle of rotation. The unit is °. The range is 0≤P≤360°.
M98 P_ The sequence number of subprogram for producing a shape on a part
G69 Deactivate the coordinate system rotation.

Function
These command can rotate a programmed shape at a specified angle.

Note
1) Coordinate system rotation command is not applicable to the tool compensation
function. The system would rotate the coordinate system before executing the tool
offset function.
2) When coordinate system rotation command is used with scaling function, scaling
is proceeded before the rotation command.

89
 9. Functions to Simplify Programming
Example
Use the rotation command to machine a part. The depth of cutting is 5mm. The starting
point is 50mm away from the workpiece.
Y X’

③
②

Y’ 20
20

45° ① X
O 20 10
10
Figure 9.5 Coordinate System Rotation – Example
%0068 ; Main program
N10 G92 X0 Y0 Z50
N15 G90 G17 M03 S600
N20 G43 Z-5 H02
N25 M98 P200 ; Machining ①
N30 G68 X0 Y0 P45 ; Rotation degree 45°
N40 M98 P200 ; Machining ②
N60 G68 X0 Y0 P90 ; Rotation degree 90°
N70 M98 P200 ; Machining ③
N20 G49 Z50
N80 G69 M05 M30 ; Rotation cancel
%200 ; Subprogram (①)
G41 G01 X20 Y-5 D02 F300
N105 Y0
N110 G02 X40 I10
N120 X30 I-5
N130 G03 X20 I−5
N140 G00 Y-6
N145 G40 X0 Y0
90
 9. Functions to Simplify Programming
N150 M99

9.4 Canned Cycles

To simplify programming, the canned cycle command can execute the specific operation
using one G code, instead of several separated G commands in the program.

In general, a canned cycle consists of six operations.

Operation 1
Initial level
Operation 2
Operation 6
Point R level

Operation 3 Operation 5

Rapid traverse
Operation 4
Feed

Figure 9.6 Sequence of canned cycle operation

1) Positioning to the initial point
2) Rapid traverse to point R
3) Hole machining
4) Operation at the bottom of hole
5) Retraction to point R
6) Retraction to the initial point

91
 9. Functions to Simplify Programming

9.4.1 Return to the Initial Point/R point Level (G98, G99)

Programming

⎧G98⎫
⎨ ⎬ G_ X_ Y_ Z_ R_ Q_ P_ I_ J_ K_ F_ L_
⎩G99 ⎭

Explanation of the parameters

G98 Return to the initial point
G99 Return to point R level
The other parameters would be explain in the specific canned cycle.

Function
Generally, G99 is used for the first drilling operation. G98 is used for the last drilling
operation.
G98(Return to initial level) G99(Return to point R level)

Initial level

Point R level

Figure 9.7 Return to the initial point/R point level

92
 9. Functions to Simplify Programming

9.4.2 High-speed Peck Drilling Cycle (G73)

Programming

⎧G98⎫
⎨ ⎬ G73 X_ Y_ Z_ R_ Q_ P_ K_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
Q Depth of cutting for each cutting feed in the incremental command
P Dwell time at the bottom of a hole
K Retraction amount at each time in the incremental command
F Cutting feedrate
L Number of repeats

Initial level

Point R Point R Point R level

q q
k k

q G98 q G99
k k

q q

P P
Point Z Point Z

Figure 9.8 High-speed Peck Drilling Cycle

93
 9. Functions to Simplify Programming
Function
This command can be used to drill a hole intermittently, so that the operator can remove the
chips during machining.

Note
1) If the value of Z/K/Q is zero, G73 would not be performed.
2) |Q|>|K|

Example
Use a tool (Φ10) to drill a hole.

25
X

Z 20 40
35

Figure 9.9 High-speed Peck Drilling – Example

%3337
N10 G92 X0 Y0 Z80
N15 M03 S700
N20 G00 Y25
N30 G98G73G91X20G90R40P2Q-10K2Z-3L2F80
N40 G00 X0 Y0 Z80
N45 M30

94
 9. Functions to Simplify Programming

9.4.3 Left-hand Tapping Cycle (G74)

Programming

⎧G98⎫
⎨ ⎬ G74 X_ Y_ Z_ R_ P_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of a hole
F Thread lead
L Number of repeats

Function
G74 command can create a reverse thread. Tapping is performed by turning the spindle
counterclockwise. Then, the spindle turns clockwise for retraction when the tool reaches the
bottom of the hole.
G98 G99

Initial level

Spindle Spindle
CCW CCW
Point R Point R Point R level

P Point Z P Point Z

Spindle CW Spindle CW

Figure 9.10 Left-hand Tapping Cycle (G74)

95
 9. Functions to Simplify Programming
Note
If the value of Z is zero, G74 would not be performed.

Rigid Tapping Mode

There are two ways for the rigid tapping:
1) C-axis tapping: the tapping is performed along C-axis.
2) Z-axis tapping: the tapping is performed along Z-axis.

The default setting is Z-axis tapping. To set the C-axis tapping, M29 is used (M29 is modal
M code). The format of setting the C-axis tapping is as follows:
M29 ; C-axis tapping is set as rigid tapping mode
G74 xx xxxxx ; C-axis tapping is performed

Example
Use the tool (M10 × 1) for the left-hand tapping.
Y

X
50
Z
35

X
M10 × 1
Figure 9.11 Left-hand Tapping – Example

%3339
N10 G92 X0 Y0 Z80 F200
N15 M04 S300
N20 G98G74X50Y40R40P10G90Z-5F1
N30 G00 X0 Y0 Z80
N40 M30

96
 9. Functions to Simplify Programming

9.4.4 Fine Boring Cycle (G76)

Programming

⎧G98⎫
⎨ ⎬ G76 X_ Y_ Z_ R_ P_ I_ J_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of a hole
I Shift amount along X-axis at the bottom of a hole
J Shift amount along Y-axis at the bottom of a hole
F Cutting feedrate
L Number of repeats

Function
G76 command would bore a hole precisely. When the tool reaches the bottom of the hole,
the spindle stops, and the tool is retracted to the direction opposite to the tool tip.
Spindle CW
Initial level Spindle CW

G98
Point R Point R G99

P Point Z P Point Z

Shift amount Shift amount

Figure 9.12 Fine Boring Cycle (G76)
97
 9. Functions to Simplify Programming
Note
If the value of Z, G76 would not be performed.

Example
Use the tool to bore a hole on a workpiece.
Y

30
15
X
20 40
Z
35

X
Figure 9.13 Fine Boring Cycle – Example

%3341
N10 G54
N12 M03 S600
N15 G00 X0 Y0 Z80
N20 G98G76X20Y15R40P2I-5Z-4F100
N25 X40Y30
N30 G00 G90 X0 Y0 Z80
N40 M30

98
 9. Functions to Simplify Programming

9.4.5 Drilling Cycle, Spot Drilling (G81)

Programming

⎧G98⎫
⎨ ⎬ G81 X_ Y_ Z_ R_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
F Cutting feedrate
L Number of repeats

Function
G81 command can be used to drill a hole. The tool is moved at the cutting feedrate when it
is drilling a hole. Then, the tool is moved at the rapid traverse speed when it is retracting
from the bottom of the hole.

Initial level

G98 Point R
Point R Point R level

G99

Point Z Point Z

Figure 9.14 Drilling Cycle, Spot Drilling (G81)

Note
If the value of Z is zero, G81 would not be performed.
99
 9. Functions to Simplify Programming
Example
Use the tool (Φ10) to drill a hole.
Y

30
15
X
20 40
Z
15

X
Figure 9.15 Drilling Cycle, Spot Drilling - Example

%3343
N10 G92 X0 Y0 Z80
N15 M03 S600
N20 G98G81G91X20Y15G90R20Z-3P2L2F200
N30 G00 X0 Y0 Z80
N40 M30

100
 9. Functions to Simplify Programming

9.4.6 Drilling Cycle, Counter Boring Cycle (G82)

Programming

⎧G98⎫
⎨ ⎬ G82 X_ Y_ Z_ R_ P_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of the hole
F Cutting feedrate
L Number of repeats

Function
G82 command can be used to drill a counter bore or a blind bore.

Initial level

G98 Point R
Point R Point R level

G99

Point Z

Figure 9.16 Drilling Cycle, Counter Boring Cycle (G82)

Note
If the value of Z is zero, G82 would not be performed.

101
 9. Functions to Simplify Programming
Example
Use the tool to drill a counter bore.

Z 90°

35

X
Φ12

Figure 9.17 Drilling Cycle, Counter Boring Cycle – Example

%3345
N10 G92 X0 Y0 Z80
N15 M03 S600
N20 G98G82G90X25Y30R40P2Z25F200
N30 G00 X0 Y0 Z80
N40 M30

102
 9. Functions to Simplify Programming

9.4.7 Peck Drilling Cycle (G83)

Programming
⎧G98⎫
⎨ ⎬ G83 X_ Y_ Z_ R_ Q_ P_ K_ F_ L_
⎩G99⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
Q Depth of cutting for each cutting feed in the incremental command
P Dwell time at the bottom of the hole
K Retraction amount at each time in the incremental command
F Cutting feedrate
L Number of repeats

103
 9. Functions to Simplify Programming
Function
G83 command can perform a peck drilling. The intermittent cutting feed allows the operator
to remove the chips from the hole.

Initial level

G98
Point R Point R Point R level
G99
q k q k

k k
q q

q q
Point Z Point Z

Figure 9.18 Peck Drilling Cycle (G83)

Note
If the value of Z/Q/K is zero, G83 would not be performed.

Example
Use the tool (Φ10) to drill a hole.
Y

X
20 40
Z
35

X
Figure 9.19 Peck Drilling Cycle – Example
%3347
N10 G55 G00 X0 Y0 Z80
N15 Y25
N20 G98G83G91X20G90R40P2Q-10K5G91Z-43F100L2
N30 G90 G00 X0 Y0 Z80
N40 M30
104
 9. Functions to Simplify Programming

9.4.8 Tapping Cycle (G84)

Programming
⎧G98⎫
⎨ ⎬ G84 X_ Y_ Z_ R_ P_ F_ L_
⎩G99⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of the hole
F Thread lead
L Number of repeats

Function
G84 command is used for tapping. When the tool has reached the bottom of the hole, it is
retracted in the reverse direction.

Initial level

Spindle CW
Spindle CW Spindle CW Spindle CW
G98 Point R level
Point R Point R G99

P Point Z P Point Z

Spindle CCW Spindle CCW

Figure 9.20 Tapping Cycle (G84)

105
 9. Functions to Simplify Programming
Note
If the value of Z is zero, G84 would not be performed.

Example
Use the tool (M10 × 1) to drill a hole.
Y

X
50
Z
35

Figure 9.21 Peck Drilling Cycle – Example

%3349
N10 G92 X0 Y0 Z80
N15 M03 S300
N20 G98G74G91X50Y40G90R38P3G91Z-40F1
N30 G90 G0 X0 Y0 Z80
N40 M30

106
 9. Functions to Simplify Programming

9.4.9 Boring Cycle (G85)

Programming

⎧G98⎫
⎨ ⎬ G85 X_ Y_ Z_ R_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of the hole
F Cutting feedrate
L Number of repeats

Initial level

G98 Point R
Point R Point R level

G99

Point Z

Figure 9.22 Boring Cycle (G85)

Function
G85 command is used to bore a hole, which is not required the precise boring.

Note
If the value of Z is zero, G85 would not be performed.

107
 9. Functions to Simplify Programming
Example
Use the boring tool to bore a hole.
Y

15
X
20 40
Z
15

X
Figure 9.23 Boring Cycle – Example

%3351
N10 G92 X0 Y0 Z80
N15 M03 S600
N20 G98G85G91X20Y15R-42P2Z-40L2F100
N30 G90 G00 X0 Y0 Z80
N40 M30

108
 9. Functions to Simplify Programming

9.4.10 Boring Cycle (G86)

9.4.10Boring
Programming

⎧G98⎫
⎨ ⎬ G86 X_Y_Z_R_F_L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
F Cutting feedrate
L Number of repeats
Spindle CW
Spindle
Initial level CCW

Point R level
Point R G98 Point R G99

Point Z Point Z

Spindle stop Spindle stop

Figure 9.24 Boring Cycle (G86)

Function
G86 command is used to bore a hole, which is not required the precise boring.

Note
If the value of Z is zero, G86 would not be performed.

109
 9. Functions to Simplify Programming
Example
Use the reamer to bore a hole.
Y

15
X
20 40
Z
15

X
Figure 9.25 Boring Cycle – Example

%3353
N10 G92 X0 Y0 Z80
N15 G98G86G90X20Y15R38Q-10K5P2Z-2F200
N20 X40 Y30
N30 G90 G00 X0 Y0 Z80
N40 M30

110
 9. Functions to Simplify Programming

9.4.11 Back Boring Cycle (G87)

9.4.11Back
Programming
G98 G87 X_ Y_ Z_ R_ P_ I_ J_ F_ L_

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of the hole
I Shift amount along X-axis at the bottom of a hole
J Shift amount along Y-axis at the bottom of a hole
F Cutting feedrate
L Number of repeats

Function
G87 command is used to bore a hole.
Shift amount

Spindle CW
G98

Point Z
P
Spindle CW
Point R

Figure 9.26 Boring Cycle (G87)

111
 9. Functions to Simplify Programming
Note
1) If the value of Z is zero, G87 would not be performed.
2) G87 can not be used with G99.

Example
Use the reamer to bore a hole (Φ28).

15
X
20 40

2*Φ20
Z

35
20
X
2*Φ28

Figure 9.27 Back Boring Cycle – Example

%3355
N10G92 X0 Y0 Z80
N15M03 S600
N20G00 Y15 F200
N25G98G87G91X20I-5R-83P2Z23L2
N30G90 G00 X0 Y0 Z80 M05
N40M30

112
 9. Functions to Simplify Programming

9.4.12 Manual Boring Cycle (G88)

9.4.12Manual
Programming

⎧G98⎫
⎨ ⎬ G88 X_ Y_ Z_ R_ P_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of the hole
F Cutting feedrate
L Number of repeats

Initial level Spindle CW

G98 Point R level

Point R Point R G99

Point Z Point Z
P P
Spindle stop Spindle stop
after dwell after dwell

Figure 9.28 Manual Boring Cycle (G88)

Function
G88 command can be used to bore a hole precisely. The main difference is that the tool is
returned to the initial point or the point R in the manual mode key (on the machine control
panel).

113
 9. Functions to Simplify Programming
Note
1) If the value of Z is zero, G88 would not be performed.
2) When manually moving the tool for retraction, the position of tool must be higher
than the initial point (G98) or the point R (G99).

Example
Use the reamer to bore a hole.
Y

15
X
20 40
Z
15

X
Figure 9.29 Manual Boring Cycle – Example

%3357
N10 G54
N12 M03 S600
N15 G00 X0 Y0 Z80
N20 G98G88G91X20Y15R-42P2I-5Z-40L2F100
N30 G00 G90 X0 Y0 Z80
N40 M30

114
 9. Functions to Simplify Programming

9.4.13 Boring Cycle (G89)

9.4.13Boring
Programming

⎧G98⎫
⎨ ⎬ G89 X_ Y_ Z_ R_ P_ F_ L_
⎩G99 ⎭

Explanation of the parameters

X,Y Coordinate value of the hole position on XY plane in the absolute command, or the
coordinate value of the hole position with reference to the initial point on XY plane in the
incremental command
Z Coordinate value of the hole position on Z axis in the absolute command, or the
coordinate value of the hole position with reference to the point R on Z axis in the
incremental command
R Coordinate value of the point R in the absolute command, or the coordinate value
of the point R with reference to the initial point in the incremental command
P Dwell time at the bottom of the hole
F Cutting feedrate
L Number of repeats

Initial level

G98 Point R level

Point R Point R G99

P Point Z P Point Z

Figure 9.30 Boring Cycle (G89)

Function
G89 command is used to bore a hole.

Note
If the value of Z is zero, G89 would not be performed.

115
 9. Functions to Simplify Programming

9.4.14 Canned Cycle Cancel (G80)

9.4.14Canned
Programming
G80

Explanation the parameters

G80 a canned cycle is cancelled. Meanwhile, the point R and the point Z (the bottom of
the hole) are all cancelled.

Function
G80 is used to cancel a canned cycle.

116
 9. Functions to Simplify Programming

9.5 Summary
In summary, five points should be noted when using the canned cycle.
1) Use M03/M04 to rotate the spindle before the canned cycle starts
2) One of the parameters (X, Y, Z, R) must be used in the canned cycle command.
3) When using G74, G84, or G86 command, G04 command can be used in the
canned cycle to insure that the spindle is reached the appropriate speed.
4) G00~G03 can also be used to cancel the canned cycle. When G00~G03 and the
canned cycle command are in the same block, the execution depends on the
sequence of these commands.
5) If M is specified in the canned cycle, the cycle only starts working after sending M
signal is done.

117
 9. Functions to Simplify Programming
Example 1
Use the canned cycle command to bore a hole. The tool is 100mm away from the workpiece,
and the depth of cut is 10mm.

50
19

40

40 40 40 40

17 18
Figure 9.31 Canned Cycle – Example 1

(i) G81 command is used at first

%1000
G92 X0 Y0 Z30
G91 G00 M03 S600
G98 G81 X40 Y40 G90 R2 Z−10 F200
G91 X40 L3
Y50
X-40 L3
G90 G80 X0 Y0 Z0 M05
M30
(ii) Then, G84 command is used
%2000
G92 X0 Y0 Z30
G91 G00 M03 S600
G98 G84 X40 Y40 G90 R2 Z−10 F100
G91 X40 L3
Y50
X-40 L3
G90 G80 X0 Y0 Z0 M05
M30

118
 9. Functions to Simplify Programming
Example 2
Use the tool (Φ20) to machine the contour. Then, use the tool (Φ16) to machine the concave.
And use the tool (Φ6, Φ8) to bore a hole.

22
12

14

14
56
14

R10 12
14 14 14 14
80

Figure 9.32 Canned Cycle – Example 2

%3360
G92 x-20 y-20 z100
M03 S500
N1 M06 T01
G00 G43 Z-23 H01
G01 G41 X0 Y-8 D01 F100
Y42
X7 Y56
X80
Y12
G02 X70 Y0 R10
G01 X-10
G00 G40 X-20 Y-20
G49 Z100
N2 M06 T2
G00 G43 Z-10 H02
119
 9. Functions to Simplify Programming
X5 Y-10
G01 Y66 F100
X19
Y-10
X20
Y66
G00 G49 Z100
G00 X-20 Y-20
N3 M06 T03
G00 G43 Z10 H03
G98 G73 X14 Y26 Z-23 R-6 Q-5F50
G99 G73 X42 Y40 Z-23 R4 Q-5F50
G99 G73 X42 Y12 Z-23 R4 Q-5F50
G98 G73 X56 Y26 Z-23 R4 Q-5F50
G00 G49 Z100
X-20 Y-20
M05
M30

120
 9. Functions to Simplify Programming
Example 3
Use the tool (Φ20) to machine the contour. Then, use the tool (Φ16) to machine the concave.
And use the tool (Φ6) to drill a hole.

22
12

Iron pad
10 13 23

14
56
R8
14

14

22 36
80

Figure 9.33 Canned Cycle – Example 3

%3361
G92 x-20 y-20 z100
M03 S500
N1 M06 T01
G00 G43 Z-23 H01
G01 G41 X0 Y-8 D01 F100
Y56
X80
Y0
X-10
G00 G40 X-20 Y-20
G49 Z100
N2 M06 T2
G00 G43 Z-10 H02

121
 9. Functions to Simplify Programming
X5 Y-10
G01 Y70 F100
X13
Y-10
X14
Y70
G00 X75
G01 Y-10 F100
X67
Y70
X66
Y-10
G00 G49 Z100
G00 X-20 Y-20
N3 M06 T03
G00 G43 Z10 H03
G98 G73X12Y14Z-23R-6Q-5K3F50
G73G91X23G90Z-23R4Q-5K3L2F50
G73X58Y42Z-23R-6Q-5K3F50
G73G91X-23G90Z-23R4Q-5K3L2F50
G00 G49 Z100
X-20 Y-20
M05
M30

122
 10. Custom Macro

10 Custom Macro
Similarly to subprogram, the custom macro function allows operators to define their own
program. The way of calling the custom macro is same as subprogram’s.

The difference is that custom macro allows use of variables, arithmetic and logic operations,
selection and repetition.

123
 10. Custom Macro

10.1 Variables
Format and Explanation
#_ Variable is composed of a number sign (#) and a number.

Example
#1
#1=#2+100

10.1.1 Type of Variables

10.1.1Type
There are four types of variables.
Table 10 1 Type of Variables
Variable
Type of variables Function
number
#0~#49 Local variables They are used in a macro program.
They can be shared among different
#50~#199 Common variables
macro programs.
#200~#249 0 layers local variables
#250~#299 1 layers local variables
#300~#349 2 layers local variables
#350~#399 3 layers local variables
#400~#449 4 layers local variables
#450~#499 5 layers local variables
#500~#549 6 layers local variables
#550~#599 7 layers local variables
#600~ System variables They are used to read and write NC data.

Note:
1) The operator can only use the #0~#599 local variables for programming.
2) Variables after #599 can only be used by the system programmer for reference.

124
 10. Custom Macro

10.1.2 System Variables

10.1.2System
#1000 “current position X in machine coordinate system”
#1001 “current position Y in machine coordinate system”
#1002 “current position Z in machine coordinate system”
#1003 “current position A in machine coordinate system”
#1004 “current position B in machine coordinate system”
#1005 “current position X in machine coordinate system”
#1006 “current position U in machine coordinate system”
#1007 “current position V in machine coordinate system”
#1008 “current position W in machine coordinate system”
#1009 “diameter programming”
#1010 “position X – machine coordinate system in programming”
#1011 “position Y – machine coordinate system in programming”
#1012 “position Z – machine coordinate system in programming”
#1013 “position A – machine coordinate system in programming”
#1014 “position B – machine coordinate system in programming”
#1015 “position C – machine coordinate system in programming”
#1016 “position U – machine coordinate system in programming”
#1017 “position V – machine coordinate system in programming”
#1018 “position W – machine coordinate system in programming”
#1019 reserved
#1020 “position X – workpiece coordinate system in programming”
#1021 “position Y – workpiece coordinate system in programming”
#1022 “position Z – workpiece coordinate system in programming”
#1023 “position A – workpiece coordinate system in programming”
#1024 “position B – workpiece coordinate system in programming”
#1025 “position C – workpiece coordinate system in programming”
#1026 “position U – workpiece coordinate system in programming”
#1027 “position V – workpiece coordinate system in programming”
#1028 “position W – workpiece coordinate system in programming”
#1029 reserved
#1030 “origin X in workpiece coordinate system”
125
 10. Custom Macro
#1031 “origin Y in workpiece coordinate system”
#1032 “origin Z in workpiece coordinate system”
#1033 “origin A in workpiece coordinate system”
#1034 “origin B in workpiece coordinate system”
#1035 “origin C in workpiece coordinate system”
#1036 “origin U in workpiece coordinate system”
#1037 “origin V in workpiece coordinate system”
#1038 “origin W in workpiece coordinate system”
#1039 “axis of the coordinate system”
#1040 “origin X of G54”
#1041 “origin Y of G54”
#1042 “origin Z of G54”
#1043 “origin A of G54”
#1044 “origin B of G54”
#1045 “origin C of G54”
#1046 “origin U of G54”
#1047 “origin V of G54”
#1048 “origin W of G54”
#1049 reserved
#1050 “origin X of G55”
#1051 “origin Y of G55”
#1052 “origin Z of G55”
#1053 “origin A of G55”
#1054 “origin B of G55”
#1055 “origin C of G55”
#1056 “origin U of G55”
#1057 “origin V of G55”
#1058 “origin W of G55”
#1059 reserved
#1060 “origin X of G56”
#1061 “origin Y of G56”
#1062 “origin Z of G56”

126
 10. Custom Macro
#1063 “origin A of G56”
#1064 “origin B of G56”
#1065 “origin C of G56”
#1066 “origin U of G56”
#1067 “origin V of G56”
#1068 “origin W of G56”
#1069 reserved
#1070 “origin X of G57”
#1071 “origin Y of G57”
#1072 “origin Z of G57”
#1073 “origin A of G57”
#1074 “origin B of G57”
#1075 “origin C of G57”
#1076 “origin U of G57”
#1077 “origin V of G57”
#1078 “origin W of G57”
#1079 reserved
#1080 “origin X of G58”
#1081 “origin Y of G58”
#1082 “origin Z of G58”
#1083 “origin A of G58”
#1084 “origin B of G58”
#1085 “origin C of G58”
#1086 “origin U of G58”
#1087 “origin V of G58”
#1088 “origin W of G58”
#1089 reserved
#1090 “origin X of G59”
#1091 “origin Y of G59”
#1092 “origin Z of G59”
#1093 “origin A of G59”
#1094 “origin B of G59”

127
 10. Custom Macro
#1095 “origin C of G59”
#1096 “origin U of G59”
#1097 “origin V of G59”
#1098 “origin W of G59”
#1099 reserved
#1100 “break point X”
#1101 “break point Y”
#1102 “break point Z”
#1103 “break point A”
#1104 “break point B”
#1105 “break point C”
#1106 “break point U”
#1107 “break point V”
#1108 “break point W”
#1109 “axis of the coordinate system”
#1110 “middle point X of G28”
#1111 “middle point Y of G28”
#1112 “middle point Z of G28”
#1113 “middle point A of G28”
#1114 “middle point B of G28”
#1115 “middle point C of G28”
#1116 “middle point U of G28”
#1117 “middle point V of G28”
#1118 “middle point W of G28”
#1119 “shield of G28”
#1120 “mirror-image position X”
#1121 “mirror-image position Y”
#1122 “mirror-image position Z”
#1123 “mirror-image position A”
#1124 “mirror-image position B”
#1125 “mirror-image position C”
#1126 “mirror-image position U”

128
 10. Custom Macro
#1127 “mirror-image position V”
#1128 “mirror-image position W”
#1129 “shield of mirror image”
#1130 “rotational axis 1”
#1131 “rotational axis 2”
#1132 “rotation angle”
#1133 “shield of rotational axis”
#1134 reserved
#1135 “scale axis 1”
#1136 “scale axis 2”
#1137 “scale axis 3”
#1138 “scaling”
#1139 “shield of scale axis”
#1140 “code 1 of changing a coordinate system”
#1141 “code 2 of changing a coordinate system”
#1142 “code 3 of changing a coordinate system”
#1143 reserved
#1144 “number of tool length compensation”
#1145 “number of tool radius compensation”
#1146 “linear axis 1”
#1147 “linear axis 2”
#1148 “shield of virtual axis”
#1149 “specified feedrate”
#1150 “modal value of G code – 0”
#1151 “modal value of G code – 1”
#1152 “modal value of G code – 2”
#1153 “modal value of G code – 3”
#1154 “modal value of G code – 4”
#1155 “modal value of G code – 5”
#1156 “modal value of G code – 6”
#1157 “modal value of G code – 7”
#1158 “modal value of G code – 8”

129
 10. Custom Macro
#1159 “modal value of G code – 9”
#1160 “modal value of G code – 10”
#1161 “modal value of G code – 11”
#1162 “modal value of G code – 12”
#1163 “modal value of G code – 13”
#1164 “modal value of G code – 14”
#1165 “modal value of G code – 15”
#1166 “modal value of G code – 16”
#1167 “modal value of G code – 17”
#1168 “modal value of G code – 18”
#1169 “modal value of G code – 19”
#1170 “residual CACHE”
#1171 “spare CACHE”
#1172 “residual buffer storage”
#1173 “spare buffer storage”
#1174 reserved
#1175 reserved
#1176 reserved
#1177 reserved
#1178 reserved
#1179 reserved
#1180 reserved
#1181 reserved
#1182 reserved
#1183 reserved
#1184 reserved
#1185 reserved
#1186 reserved
#1187 reserved
#1188 reserved
#1189 reserved
#1190 “customized input”

130
 10. Custom Macro
#1191 “customized output”
#1192 “customized output shield”
#1193 reserved
#1194 reserved

131
 10. Custom Macro

10.2 Constant
PI π, 3.14151926
TRUE True condition
FALSE False condition

132
 10. Custom Macro

10.3 Operators and Expression

1) Mathematic operator
+, -, *, /

2) Conditional operator
EQ(=), NE(≠), GT(＞), GE(≥), LT(＜), LE(≤)

3) Logic operator
AND, OR, NOT

4) Function
SIN Sine
COS Cosine
TAN Tangent
ATAN Arctangent
ATAN2 Arctangent2
ABS Absolute value
INT Integer
SIGN Sign
SQRT Square root
EXP Exponential function

5) Expression
The expressions are composed of constants, operators and variables.

Example:
175/SQRT[2] * COS[55 * PI/180 ];
#3*6 GT 14;

133
 10. Custom Macro

10.4 Assignment
Assignment refers to assign a variable value to a constant or expression.

Format:
Variable=constant or expression

Example
#2 = 175/SQRT[2] * COS[55 * PI/180]
#3 = 124.0

134
 10. Custom Macro

10.5 Selection statement IF, ELSE,ENDIF

Format (i)
IF Conditional expression
…
ELSE
…
ENDIF

Explanation (i)
If the specified conditional expression is satisfied, the statements between IF and ELSE are
executed. If the specified conditional expression is not satisfied, the statements between
ELSE and ENDIF are executed.

Format (ii)
IF Conditional expression
…
ENDIF

Explanation (ii
ii))
If the specified conditional expression is satisfied, the statements between IF and ENDIF are
executed. If the specified conditional expression is not satisfied, the system would proceed
to the blocks after ENDIF.

135
 10. Custom Macro

10.6 Repetition Statement WHILE, ENDW

Format
WHILE Conditional expression
…
ENDW

Explanation
When the conditional expression is satisfied, the statements between WHILE and ENDW
are executed. If the conditional expression is not satisfied, the system would proceed to the
blocks after ENDW.

136
 10. Custom Macro

10.7 Macro Call

The following table shows the local variable and the corresponding system variable when it
is macro call.
Table 10 2 Transmission of Macro Call

Local variables System variables in macro call

#0 A
#1 B
#2 C
#3 D
#4 E
#5 F
#6 G
#7 H
#8 I
#9 J
#10 K
#11 L
#12 M
#13 N
#14 O
#15 P
#16 Q
#17 R
#18 S
#19 T
#20 U
#21 V
#22 W
#23 X
#24 Y
#25 Z
#26 Mode value of Z-plane in canned cycle
#27 Unavailable
#28 Unavailable
#29 Unavailable
#30 Absolute coordinate of 0-axis when subprogram call
#31 Absolute coordinate of 1-axis when subprogram call
#32 Absolute coordinate of 2-axis when subprogram call
#33 Absolute coordinate of 3-axis when subprogram call
#34 Absolute coordinate of 4-axis when subprogram call
#35 Absolute coordinate of 5-axis when subprogram call
#36 Absolute coordinate of 6-axis when subprogram call
#37 Absolute coordinate of 7-axis when subprogram call
#38 Absolute coordinate of 8-axis when subprogram call
137
 10. Custom Macro
Explanation
1) To check whether the variable is defined in the program, the format is as follows:
AR [#Variable number]
Return:
0 – the variable is not defined
90 – the variable is defined as absolute command G90
91 – the variable is defined as incremental command G91
2) When it is macro call (subprogram or canned cycle) with G code, the system
would copy the system variables (A~Z) to local variables #0-#25 in the macro.
Meanwhile, the system can copy the axis position (machine coordinate value in
absolute command) of nine channels to local variables #30-#38.
3) When calling a subprogram, the subprogram can modify the system mode.
4) When calling a canned cycle, the canned cycle does not modify the system mode.

138
 10. Custom Macro

10.8 Example
Example 1
Use the tool (Φ10) to machine a frustum of a cone and an inclined plane. The included angle
between the frustum of a cone and an incline plane is 10°. The first time of finishing amount
is 1mm, and the second time of finishing amount is 3mm.
Y

Φ175 X

10°

Z
10
10

Figure 10.1 Custom Macro – Example 1

%8002
#10=10.0 ; Height of column
#11=10.0 ; Height of square
#12=124.0
#13=124.0
N01 G92 X0.0 Y0.0 Z0.0
N05 G00 Z10.0
#0=0
N06 G00 X[−#12] Y[−#13]
N07 Z[−#10] M03 S600
WHILE #0 LT 3 ; Column machining
N[08+#0*6] G01 G42 X[−#12/2] Y[−175/2] F280.0 D[#0+1]
N[09+#0*6] X[0] Y[−175/2]
N[10+#0*6] G03 J[175/2]
N[11+#0*6] G01 X[#12/2] Y[−175/2]
139
 10. Custom Macro
N[12+#0*6] G40 X[#12] Y[−#13]
N[13+#0*6] G00 X[-#12] Y[−#13]
#0=#0+1
ENDW
N100 Z[-#10-#11]
#2=175/SQRT[2]*COS[55*PI/180]
#3=175/SQRT[2]*SIN[55*PI/180]
#4=175*COS[10*PI/180]
#5=175*SIN[10*PI/180]
#0=0
WHILE #0 LT 3 ; Square machining
N[101+#0*6] G01 G90 G42 X[−#2] Y[−#3] F280.0 D[#0+1]
N[102+#0*6] G91 X[+#4] Y[+#5]
N[103+#0*6] X[−#5] Y[+#4]
N[104+#0*6] X[−#4] Y[−#5]
N[105+#0*6] X[+#5] Y[−#4]
N[106+#0*6] G00 G90 G40 X[−#12] Y[−#13]
#0=#0+1
ENDW
G00 X0 Y0 M05
M30

140
 10. Custom Macro
Example 2
Use the tool to machine an ellipse. ( X = a × cos α , Y = b × sin α )

Figure 10.2 Custom Macro – Example 2

%0001
#0=5 ; the radius of tool
#1=20 ; the value of a
#2=10 ; the value of b
#3=0 ; the value of α
N1 G92 X0 Y0 Z10
N2 G00 X[2*#0+#1] Y[2*#0+#2]
N3 G01 Z0
N4 G41 X[#1]
N5 WHILE #3 GE [-360]
N6 G01 X[#1*COS[#3*PI/180]] Y[#2*SIN[#3*PI/180]]
N7 #3=#3-5
ENDW
G01 G91 Y[-2*#0]
G90 G00 Z10
G40 X0 Y0
M30

141
 10. Custom Macro
Example 3
Use the drilling tool (diameter is 20mm) to drill a thread (M60 × 1.5). The smaller diameter
is 60-2+0.376=58.376. The height of workpiece is 10mm.

Figure 10.3 Custom Macro – Example 3

%0027
N1 G92 X0 Y0 Z30
N2 MO3 S500
N3 G01 Z11 X19.178 F1200
N4 #0=58.376/2-10+0.3
WHILE #0 LE 20
N5 G91 G03 I[-#0] Z-1.5 L8
N6 G90 G01 X0
N7 Z11
N8 #0=#0+0.2
N9 G01 X[#0]
N10 ENDW
N11 G01 X20
N12 G91 G03 I-20 Z-1.5 L8
N13 G90 G00 X0
N14 G00 Z30
N15 X30 Y-50
N16 M30

142
 10. Custom Macro
Example 4
Use ball-end milling tool to machine a fillet surface (R5).

Z
R5

15
30
X

R6

X
40 30

Figure 10.4 Custom Macro – Example 4

%0001
G92 X-30 Y-30 Z25 ; the tool is at the center of the circle.
#0=5 ; the radius of fillet surface
#1=4 ; the radius of the tool
#2=180 ; the value of γ, the unit is degree.
WHILE #2 GT 90
G01 Z[25+[#0+#1]*SIN[#2*PI/180]] ; the height on Z axis
#101=ABS[[#0+#1]*COS[#2*PI/180]]-#0 ; the radius offset
G01 G41 X-20 D101
Y14
G02 X-14 Y20 R6
G01 X14
G02 X20 Y14 R6
G01 Y-14
G02 X14 Y-20 R6
G01 X-14
G02 X-20 Y-14 R6
G01 X-30
G40 Y-30
#2=#2-10
ENDW
M30

143