<<Contents>> <<Index>>

General EJX120A
Specifications Differential Pressure Transmitter

GS 01C25B03-01EN

The high performance draft range differential pressure

transmitter EJX120A features single crystal silicon
resonant sensor and is suitable to measure liquid,
gas, or steam flow as well as liquid level, density and
pressure. EJX120A outputs a 4 to 20 mA DC signal
corresponding to the measured differential pressure.
Other key features include quick response, remote
set-up using communications, diagnostics and optional
status output for pressure high/low alarm. The multi-
sensing technology provides the advanced diagnostic
function to detect such abnormalities as an impulse
line blockage or heat trace breakage. FOUNDATION
Fieldbus and PROFIBUS PA protocol types are also
available. All EJX series models in their standard
configuration, with the exception of the Fieldbus and
PROFIBUS types, are certified by TÜV as complying
with SIL 2 for safety requirement.

 STANDARD SPECIFICATIONS
Refer to GS 01C25T02-01EN for Fieldbus
communication type and GS 01C25T04-01EN for
PROFIBUS PA communication type for the items Square Root Output Accuracy
marked with “◊.” The square root accuracy is a percent of flow span.

Output Accuracy
□ SPAN AND RANGE LIMITS 50% or Greater Same as reference accuracy
Reference accuracy × 50
Measurement inH2O mbar mmH2O 50% to Dropout point
kPa Square root output (%)
Span/Range (/D1) (/D3) (/D4)
0.025 to 1 0.1 to 4 0.25 to 10 2.5 to 100 Ambient Temperature Effects per 28°C (50°F)
Span
E (0.1 to 1) (0.4 to 4) (1 to 10) (10 to 100) Change
Range -1 to 1 -4 to 4 -10 to 10 -100 to 100 ±(0.1% Span + 0.15% URL)
( ) show the span limits for square root output. Stability (All normal operating condition, including
overpressure effects)
□ PERFORMANCE SPECIFICATIONS ±0.15% of URL per one year
Zero-based calibrated span, linear output, wetted Power Supply Effects(Output signal code D, E
parts material code S and silicone oil, unless and J)
otherwise mentioned. ±0.005 % per Volt (from 21.6 to 32 V DC, 350Ω)
For Fieldbus and PROFIBUS PA communication Vibration Effects
types, use calibrated range instead of span in the Amplifier housing code 1 and 3:
following specifications. Less than 0.1% of URL when tested per the
Specification Conformance requirements of IEC60770-1 field or pipeline
EJX series ensures specification conformance to at with high vibration level (10-60 Hz, 0.21 mm
least ±3σ. displacement/60-2000 Hz 3 g)
Reference Accuracy of Calibrated Span Amplifier housing code 2:
(includes terminal-based linearity, hysteresis, and Less than ±0.1% of URL when tested per the
repeatability) requirements of IEC60770-1 field with general
application or pipeline with low vibration level (10-60
Measurement span E Hz 0.15mm displacement /60-500 Hz 2g)
Reference X ≤ span ±0.09% of Span Mounting Position Effects
accuracy X > span ±(0.015+0.03 URL/span)% of Span Rotation in diaphragm plane has no effect. Tilting
X 0.4 kPa (1.6 inH2O) up to 90 degree will cause zero shift up to 0.4 kPa
URL (1.6 inH2O) which can be corrected by the zero
1 kPa (4 inH2O) adjustment.
(upper range limit)
Response Time (Differential pressure) “◊”
150 ms
When amplifier damping is set to zero and including
dead time of 45 ms (nominal)

Yokogawa Electric Corporation GS 01C25B03-01EN

2-9-32, Nakacho, Musashino-shi, Tokyo, 180-8750 Japan ©Copyright Sep. 2007
Tel.: 81-422-52-5690 Fax.: 81-422-52-2018 20th Edition Mar. 2019
<<Contents>> <<Index>> 2
□ FUNCTIONAL SPECIFICATIONS Local Parameter Setting (Output signal code D, E,
and J)
Output “◊” Parameter configuration by the external zero
Two wire 4 to 20 mA DC output with digital adjustment screw and push button (Integral indicator
communications, linear or square root programmable. code E) offers easy and quick setup for parameters of
BRAIN or HART FSK protocol are superimposed on Tag number, Unit, LRV, URV, Damping, Output mode
the 4 to 20 mA signal. (linear/square root), Display out 1, and Re-range by
Output range: 3.6 mA to 21.6 mA applying actual pressure (LRV/URV).
Output limits conforming to NAMUR NE43 can be
pre-set by option code C2 or C3. Self Diagnostics
CPU failure, hardware failure, configuration error, and
Failure Alarm (Output signal code D, E and J) over-range error for differential pressure, and capsule
Analog output status at CPU failure and hardware temperature.
error; User-configurable process high/low alarm for
Up-scale: 110%, 21.6 mA DC or more (standard) differential pressure is also available, and its
Down-scale: −5%, 3.2 mA DC or less status can be output when optional status output is
Analog output status at process abnormality (Option specified.
code /DG6);
The result of process abnormality detected by the Advanced Diagnostics (optional) “◊”
advanced diagnostic function can be reflected to Applicable for Output signal code E, J and F.
an analog alert status. The following three setting • Impulse line blockage detection
modes are available. The impulse line condition can be calculated and
detected by extracting the fluctuation component
Mode from the differential pressure signal.
Burnout Fall back Off • Heat trace monitoring
The change of the flange temperature calculated by
110%,
Standard
21.6mA or more Holds to a
using the two temperature sensors built in the EJX
enables to detect the heat trace breakage or the
-2.5%, specified value
/C1 abnormal temperature due to the failure.
3.6mA or less within the
Normal output Signal Characterizer (Output signal code D, E
Option -1.25%, output range
/C2 and J)
Code 3.8mA or less from 3.6mA to
103.1%, 21.6mA User-configurable 10-segment signal characterizer
/C3 for 4 to 20 mA output.
20.5mA or more
Status Output (optional, output signal code D, E
Damping Time Constant (1st order) and J)
Amplifier damping time constant is adjustable from One transistor contact output (sink type) to output
0.00 to 100.00 s by software and added to response the status of user configurable high/low alarm for
time. differential pressure.
Note: For BRAIN protocol type, when amplifier software Contact rating: 30 V DC, 120 mA DC max.
damping is set to less than 0.5 s, communication
Refer to ‘Terminal Configuration’ and ‘Wiring Example
may occasionally be unavailble during the
operation, especially while output changes for Analog Output and Status Output.’
dynamically. The default setting of damping SIL Certification
ensures stable communication. EJX series transmitters except Fieldbus and
Update Period “◊” PROFIBUS communication types are certified by
Differential pressure: 45 ms TÜV in compliance with the following standards;
Zero Adjustment Limits IEC 61508: 2010; Part1 to Part 7
Zero can be fully elevated or suppressed, within the Functional Safety of Electrical/electronic/
lower and upper range limits of the capsule. programmable electronic related systems; SIL 2
capability for single transmitter use, SIL 3 capability
External Zero Adjustment for dual transmitter use.
External zero is continuously adjustable with
0.01% incremental resolution of span. Re-range □ NORMAL OPERATING CONDITION
can be done locally using the digital indicator with (Optional features or approval codes may
rangesetting switch. affect limits.)
Integral Indicator (LCD display, optional) “◊”
5-digit numerical display, 6-digit unit display and bar Ambient Temperature Limits
graph. −25 to 80°C (−13 to 176°F)
The indicator is configurable to display one or up to Process Temperature Limits
four of the following variables periodically.; −25 to 80°C (−13 to 176°F)
Measured differential pressure, differential pressure Ambient Humidity Limits
in %, scaled differential pressure. See also “Factory 0 to 100% RH
Setting.”
Working Pressure Limits (Silicone oil)
−50 to 50 kPa (−7.25 to 7.25 psi)

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN June 1, 2017-00
<<Contents>> <<Index>> 3
Supply & Load Requirements Safety Requirement Standards
(Output signal code D, E and J. Optional EN 61010-1, C22.2 No.61010-1
features or approval codes may affect electrical • Installation category: I
requirements.) (Anticipated transient overvoltage 330 V)
With 24 V DC supply, up to a 550Ω load can be • Pollution degree: 2
used. See graph below. • Indoor/Outdoor use

□ PHYSICAL SPECIFICATIONS
Wetted Parts Materials
600 Diaphragm, cover flange, process connector,
E-10.5 capsule gasket, and vent/drain plug
R=
External 0.0244 Digital Refer to “MODEL AND SUFFIX CODES.”
load Communication Process connector gasket
resistance range PTFE Teflon
BRAIN and HART
Fluorinated rubber for option code N2 and N3
250 Non-wetted Parts Materials
Bolting
R (Ω) B7 carbon steel, 316L SST or 660 SST
Housing
• Low copper cast aluminum alloy
10.5 16.6 25.2 42 • Low copper cast aluminum alloy with corrosion
Power supply voltage E (V DC) resistance properties (copper content ≤ 0.03%,
F01E.ai
iron content ≤ 0.15%) (optional)
Figure 1. Relationship Between Power Supply • ASTM CF-8M Stainless steel (optional)
Voltage and External Load Resistance
Coating of housing
[for aluminum housing]
Supply Voltage “◊” Polyester resin powder coating
10.5 to 42 V DC for general use and flameproof type. Mint-green paint (Munsell 5.6BG 3.3/2.9 or its
10.5 to 32 V DC for lightning protector equivalent)
(option code /A.) [for option code /P or /X2]
10.5 to 30 V DC for intrinsically safe, type n, or non- Epoxy and polyurethane resin solvent coating
incendive. Degrees of protection
Minimum voltage limited at 16.6 V DC for digital IP66/IP67, Type 4X
communications, BRAIN and HART
Cover O-rings
Load (Output signal code D, E and J) Buna-N, fluoro-rubber (optional)
0 to 1290Ω for operation
Name plate and tag
250 to 600Ω for digital communication
316 SST
Communication Requirements “◊”
Fill fluid
(Approval codes may affect electrical requirements.)
Silicone oil
BRAIN
Weight
Communication distance [Installation code 7, 8 and 9]
Up to 2 km (1.25 miles) when using CEV 3.7 kg (8.2 lb) without integral indicator, mounting
polyethylene-insulated PVC-sheathed cables. bracket, and process connector.
Communication distance varies depending on type of Add 1.5 kg (3.3lb) for Amplifier housing code 2.
cable used.
Connections
Load capacitance Refer to “MODEL AND SUFFIX CODES.”
0.22 µF or less Process connection of cover flange: IEC61518
Load inductance
3.3 mH or less < Related Instruments>
Input impedance of communicating device Power Distributor: Refer to GS 01B04T01-02E or
10 kΩ or more at 2.4 kHz. GS 01B04T02-02E
EMC Conformity Standards BRAIN TERMINAL: Refer to GS 01C00A11-00E
EN 61326-1 Class A, Table2
EN 61326-2-3
EN 61326-2-5 (for fieldbus)
European Pressure Equipment Directive
2014/68/EU
Sound Engineering Practice (for all capsules)
EU RoHS Directive
EN 50581

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN Mar. 11, 2019-00
<<Contents>> <<Index>> 4
< Reference >
1. is a registered trademark of Yokogawa
Electric Corporation.
2. FieldMate; Trademark of Yokogawa Electric
Corporation.
3. Teflon; Trademark of E.I. DuPont de Nemours &
Co.
4. Hastelloy; Trademark of Haynes International Inc.
5. HART; Trademark of the HART Communication
Foundation.
6. FOUNDATION Fieldbus; Tradmark of Fieldbus
Foundation.
7. PROFIBUS; Registered trademark of Profibus
Nutzerorganisation e.v., Karlsruhe, Germany.
Other company names and product names used in
this material are registered trademarks or trademarks
of their respective owners.

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN Mar. 11, 2019-00
<<Contents>> <<Index>> 5
 MODEL AND SUFFIX CODES
Model Suffix Codes Description
EJX120A ............................... Differential pressure transmitter
Output signal -D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (BRAIN protocol)
-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (HART 5 protocol)
-J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (HART 5 / HART 7 protocol)
(Refer to GS 01C25T01-01EN)
-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (FOUNDATION Fieldbus protocol, refer to
GS 01C25T02-01EN)
-G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (PROFIBUS PA protocol, refer to GS 01C25T04-01EN)
Measurement E . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 to 1 kPa (0.1 to 4 inH2O)
span (capsule)
Wetted parts  . . . . . . . . . . . . . . . . . . . . . . . . . Refer to “Wetted Parts Material” Table below.
material *1
Process connections 0 . . . . . . . . . . . . . . . . . . . . . . without process connector (Rc1/4 female on the cover flanges)
1 . . . . . . . . . . . . . . . . . . . . . . with Rc1/4 female process connector
2 . . . . . . . . . . . . . . . . . . . . . . with Rc1/2 female process connector
3 . . . . . . . . . . . . . . . . . . . . . . with 1/4 NPT female process connector
4 . . . . . . . . . . . . . . . . . . . . . . with 1/2 NPT female process connector
► 5 . . . . . . . . . . . . . . . . . . . . . . without process connector (1/4 NPT female on the cover flanges)
Bolts and nuts materia J . . . . . . . . . . . . . . . . . . . B7 carbon steel
G . . . . . . . . . . . . . . . . . . . 316L SST
C . . . . . . . . . . . . . . . . . . . 660 SST
Installation -7 . . . . . . . . . . . . . . . . . Vertical piping, left side high pressure, and process connection downside
-8 . . . . . . . . . . . . . . . . . Horizontal piping and right side high pressure
► -9 . . . . . . . . . . . . . . . . . Horizontal piping and left side high pressure
-U . . . . . . . . . . . . . . . . . Universal flange
Amplifier housing 1 . . . . . . . . . . . . . . Cast aluminum alloy
3 . . . . . . . . . . . . . . Cast aluminum alloy with corrosion resistance properties*2
2 . . . . . . . . . . . . . . ASTM CF-8M stainless steel*3
Electrical connection 0 . . . . . . . . . . . G1/2 female, one electrical connection without blind plugs
► 2 . . . . . . . . . . . 1/2 NPT female, two electrical connections without blind plugs
4 . . . . . . . . . . . M20 female, two electrical connections without blind plugs
5 . . . . . . . . . . . G1/2 female, two electrical connections and a blind plug*4
7 . . . . . . . . . . . 1/2 NPT female, two electrical connections and a blind plug*4
9 . . . . . . . . . . . M20 female, two electrical connections and a blind plug*4
A . . . . . . . . . . . G1/2 female, two electrical connections and a SUS316 blind plug
C . . . . . . . . . . . 1/2 NPT female, two electrical connections and a SUS316 blind plug
D . . . . . . . . . . . M20 female, two electrical connections and a SUS316 blind plug
Integral indicator D . . . . . . . . Digital indicator*5
E . . . . . . . . Digital indicator with the range setting switch (push button)*6
► N . . . . . . . . None
Mounting bracket ► B . . . . . . 304 SST 2-inch pipe mounting, flat type (for horizontal piping)
D . . . . . . 304 SST or SCS13A 2-inch pipe mounting, L type (for vertical piping)
J . . . . . . 316 SST 2-inch pipe mounting, flat type (for horizontal piping)
K . . . . . . 316 SST or SCS14A 2-inch pipe mounting, L type (for vertical piping)
N . . . . . . None
Optional Codes / Optional specification

The “►” marks indicate the most typical selection for each specification.
*1: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of
inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage
to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm
and the fill fluid can contaminate the user’s process fluids.
Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium
hypochlorite, and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the
wetted parts material.
*2: Not applicable for electrical connection code 0, 5, 7, 9 and A.
*3: Not applicable for electrical connection code 0, 5, 7 and 9.
*4: Material of a blind plug; aluminum alloy for code 5 and 9, and SUS304 for code 7.
*5: Not applicable for output signal code G.
*6: Not applicable for output signal code F.

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN June 1, 2017-00
<<Contents>> <<Index>> 6
Table. Wetted Parts Materials
Wetted parts Cover flange and process
Capsule Capsule gasket Vent/Drain plug
material code connector
Hastelloy C-276 (Diaphragm)
*2
S# ASTM CF-8M *1 PTFE Teflon 316 SST
F316L SST, 316L SST (Others)
*1: Cast version of 316 SST. Equivalent to SCS14A.
*2: Hastelloy C-276 or ASTM N10276.
The ‘#’marks indicate the construction materials conform to NACE material recommendations per MR0175/ISO15156.
Please refer to the latest standards for details. Selected materials also conform to NACE MR0103.

 OPTIONAL SPECIFICATIONS (For Explosion Protected type) “◊”

For other agency approvals and marine approvals, please refer to GS 01C25A20-01EN.

Item Description Code

Factory Mutual FM Explosionproof Approval *1
(FM) Applicable Standard: FM3600, FM3615, FM3810, ANSI/NEMA 250
Explosionproof for Class I, Division 1, Groups B, C and D, Dust-ignitionproof for Class II/III, Division 1,
FF1
Groups E, F and G, in Hazardous locations, indoors and outdoors (Enclosure: Type 4X)
“FACTORY SEALED, CONDUIT SEAL NOT REQUIRED.”
Temperature class: T6, Amb. Temp.: –40 to 60°C (–40 to 140°F)
FM Intrinsically safe Approval *1*2
Applicable Standard: FM3600, FM3610, FM3611, FM3810
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1,
Groups E, F & G and Class III, Division 1, Class I, Zone 0, in Hazardous Locations, AEx ia IIC
Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division. 2,
FS1
Groups F & G, Class I, Zone 2, Group IIC, in Hazardous Locations
Enclosure: Type 4X, Temp. Class: T4, Amb. Temp.: –60 to 60°C (–75 to 140°F)
Intrinsically Safe Apparatus Parameters
[Groups A, B, C, D, E, F and G] Vmax=30 V, Imax=200 mA, Pmax=1 W, Ci=6 nF, Li=0 µH
[Groups C, D, E, F and G] Vmax=30 V, Imax=225 mA, Pmax=1 W, Ci=6 nF, Li=0 µH
Combined FF1 and FS1 *1*2 FU1
ATEX ATEX Flameproof Approval *1
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-1:2007 (“2014” from August 1, 2017),
EN 60079-31:2014
Certificate: KEMA 07ATEX0109 X
II 2G, 2D Ex d IIC T6...T4 Gb (“Ex db IIC T6...T4 Gb” from August 1, 2017),, Ex tb IIIC T85°C Db
Degree of protection: IP66/IP67 KF22
Amb. Temp. (Tamb) for gas-proof :
T4; –50 to 75°C (–58 to 167°F), T5; –50 to 80°C (–58 to 176°F), T6; –50 to 75°C (–58 to 167°F)
Process Temp. for gas-proof (Tp):
T4; –50 to 120°C (–58 to 248°F), T5; –50 to 100°C (–58 to 212°F), T6; –50 to 85°C (–58 to 185°F)
Max. surface Temp. for dust-proof: T85°C (Tamb: –30 to 75°C, Tp: –30 to 85°C) *3
ATEX Intrinsically safe Approval *1*2
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012
Certificate: DEKRA 11ATEX0228 X
II 1G, 2D Ex ia IIC T4 Ga, Ex ia IIIC T85°C T100°C T120°C Db
Degree of protection: IP66/IP67
KS21
Amb. Temp. (Tamb) for EPL Ga: –50 to 60°C (–58 to 140°F)
Maximum Process Temp. (Tp) for EPL Ga:120°C
Electrical data: Ui=30 V, Ii=200 mA, Pi=0.9 W, Ci=27.6 nF, Li=0 µH
Amb. Temp. for EPL Db: –30 to 60°C *3
Max. surface Temp. for EPL Db: T85°C (Tp: 80°C), T100°C (Tp: 100°C), T120°C (Tp: 120°C)
Combined KF22, KS21 and ATEX Intrinsically safe Ex ic *1*2
[ATEX Intrinsically safe Ex ic]
Applicable Standard: EN 60079-0:2012+A11:2013, EN 60079-11:2012 KU22
II 3G Ex ic IIC T4 Gc, Amb. Temp.: –30 to 60°C (–22 to 140°F) *3
Ui=30 V, Ci=27.6 nF, Li=0 μH

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN June 1, 2017-00
<<Contents>> <<Index>> 7
Item Description Code
Canadian CSA Explosionproof Approval *1
Standards Certificate: 2014354
Association Applicable Standard: C22.2 No.0, C22.2 No.0.4, C22.2 No.0.5, C22.2 No.25, C22.2 No.30,
(CSA) C22.2 No.94, C22.2 No.60079-0, C22.2 No.60079-1, C22.2 No.61010-1, C22.2 No.61010-2-030
Explosion-proof for Class I, Groups B, C and D.
Dustignition-proof for Class II/III, Groups E, F and G.
When installed in Division 2, “SEAL NOT REQUIRED” Enclosure: Type 4X,
Temp. Code: T6...T4
CF1
Ex d IIC T6...T4 Enclosure: IP66/IP67
Max.Process Temp.: T4;120°C(248°F), T5;100°C(212°F), T6; 85°C(185°F)
Amb.Temp.: –50 to 75°C(–58 to 167°F) for T4, –50 to 80°C(–58 to 176°F) for T5,
–50 to 75°C(–58 to 167°F) for T6 *3
Process Sealing Certification
Dual Seal Certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required
Primary seal failure annunciation: at the zero adjustment screw
CSA Intrinsically safe Approval *1*2
Certificate: 1606623
[For CSA C22.2]
Applicable Standard: C22.2 No.0, C22.2 No.0.4, C22.2 No.25, C22.2 No.94, C22.2 No.157,
C22.2 No.213, C22.2 No.61010-1, C22.2 No.60079-0, C22.2 No.61010-2-030
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1, Groups E, F & G,
Class III, Division 1, Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division 2,
Groups F & G, Class III, Division 1
Enclosure: Type 4X, Temp. Code: T4 Amb. Temp.: –50 to 60°C(–58 to 140°F) *3
Electrical Parameters: [Intrinsically Safe] Vmax=30V, Imax=200mA, Pmax=0.9W, Ci=10nF, Li=0 µH
[Nonincendive] Vmax=30V, Ci=10nF, Li=0 µH CS1
[For CSA E60079]
Applicable Standard: CAN/CSA E60079-11, CAN/CSA E60079-15, IEC 60529:2001
Ex ia IIC T4, Ex nL IIC T4 Enclosure: IP66/IP67
Amb. Temp.: –50 to 60°C(–58 to 140°F) *3, Max. Process Temp.: 120°C(248°F)
Electrical Parameters: [Ex ia] Ui=30V, Ii=200mA, Pi=0.9W, Ci=10nF, Li=0 µH
[Ex nL] Ui=30V, Ci=10nF, Li=0 µH
Process Sealing Certification
Dual Seal Certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required
Primary seal failure annunciation: at the zero adjustment screw
Combined CF1 and CS1 *1*2 CU1
IECEx IECEx Flameproof Approval *1
Scheme Applicable Standard: IEC 60079-0:2011, IEC60079-1:2007-4
Certificate: IECEx CSA 07.0008
Flameproof for Zone 1, Ex d IIC T6...T4 Gb Enclosure: IP66/IP67 SF2
Max.Process Temp.: T4;120°C(248°F), T5;100°C(212°F), T6; 85°C(185°F)
Amb.Temp.: –50 to 75°C(–58 to 167°F) for T4, –50 to 80°C(–58 to 176°F) for T5,
–50 to 75°C(–58 to 167°F) for T6
IECEx Intrinsically safe and Flameproof Approval *1*2
Intrinsically safe Ex ia
Certificate: IECEx DEK 11.0081X
Applicable Standard: IEC 60079-0:2011, IEC 60079-11:2011
Ex ia IIC T4 Ga Enclosure: IP66/IP67
Amb. Temp.: –50 to 60°C(–58 to 140°F), Max. Process Temp.: 120°C(248°F)
Electrical Parameters: Ui=30V, Ii=200mA, Pi=0.9W, Ci=27.6nF, Li=0 μH
Intrinsically safe Ex ic
Certificate: IECEx DEK 13.0061X
Applicable Standard: IEC 60079-0:2011, IEC 60079-11:2011
SU21
Ex ic IIC T4 Gc IP code: IP66
Amb. Temp.: –30 to 60°C(–22 to 140°F) *3, Max. Process Temp.: 120°C(248°F)
Electrical Parameters: Ui=30V,Ci=27.6 nF, Li=0 μH
Flameproof
Certificate: IECEx CSA 07.0008
Applicable Standard: IEC 60079-0:2011, IEC60079-1:2007-4
Flameproof for Zone 1, Ex d IIC T6...T4 Gb Enclosure: IP66/IP67
Max.Process Temp.: T4;120°C(248°F), T5;100°C(212°F), T6; 85°C(185°F)
Amb.Temp.: –50 to 75°C(–58 to 167°F) for T4, –50 to 80°C(–58 to 176°F) for T5,
–50 to 75°C(–58 to 167°F) for T6
Combination of Combination of KU22, FU1 and CU1 *1*2*4
V1U1
Approval
*1: Applicable for Electrical connection code 2, 4, 7, 9, C and D.
*2: Not applicable for option code /AL.
*3: Lower limit of ambient temperature is –15°C (5°F) when /HE is specified.
*4: When this option code is specified, a wired tag plate (as of N4 option) shall be used for tag number.

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN June 1, 2017-00
<<Contents>> <<Index>> 8
 OPTIONAL SPECIFICATIONS
Item Description Code
Painting Color change Amplifier cover only*9 P
Amplifier cover and terminal cover, Munsell 7.5 R4/14 PR
Coating change Anti-corrosion coating*1 X2
316 SST exterior parts 316 SST zero-adjustment screw and setscrews*10 HC
Fluoro-rubber O-ring All O-rings of amplifier housing. Lower limit of ambient temperature: –15°C (5°F) HE
Lightning protector Transmitter power supply voltage: 10.5 to 32 V DC (10.5 to 30 V DC for intrinsically safe type.)
Allowable current: Max. 6000 A (1×40 µs), Repeating 1000 A (1×40 µs) 100 times A
Applicable Standards: IEC 61000-4-4, IEC 61000-4-5
Status output*2 Transistor output (sink type)
AL
Contact rating: 30 V DC, 120 mA DC(max ) Low level: 0 to 2 V DC
Oil-prohibited use*3 Degrease cleansing treatment K1
Oil-prohibited use with
Degrease cleansing and dehydrating treatment K5
dehydrating treatment*3
Calibration units*4 P calibration (psi unit) D1
bar calibration (bar unit) (See Table for Span and Range Limits.) D3
M calibration (kgf/cm2 unit) D4
Long vent*5 Total length: 119 mm (standard: 34 mm); Total length when combining with option code K1,
U1
K2, K5, and K6: 130 mm. Material: 316 SST
Output limits and failure Failure alarm down-scale: Output status at CPU failure and hardware error is −5%, 3.2mA DC
C1
operation*6 or less.
Failure alarm down-scale: Output status at CPU
NAMUR NE43 Compliant C2
failure and hardware error is −5%, 3.2 mA DC or less.
Output signal limits:
3.8 mA to 20.5 mA Failure alarm up-scale: Output status at CPU
C3
failure and hardware error is 110%, 21.6 mA or more.
Body option*7 Right side high pressure, without drain and vent plugs N1
Terminal N1 and Process connection, based on IEC61518 with female thread on both sides of cover
Side N2
flange, with blind kidney flanges on back.
L H N2, and Material certificate for cover flange, diaphragm, capsule body, and blind kidney flange N3
F02E.ai

Wired tag plate 316 SST tag plate wired onto transmitter (Tag No.: Maximum. 16 characters.) N4
Data configuration at factory*8 Software damping, Descriptor,
Data configuration for HART communication type CA
Message
Data configuration for BRAIN communication type Software damping CB
Advanced diagnostics*11 Multi-sensing process monitoring
• Impulse line blockage detection *12 DG6
• Heat trace monitoring
Material certificate*13 Cover flange *14 M01
Cover flange, Process connector *15 M11
Pressure test/ Nitrogen(N2) Gas*17
Test Pressure: 50 kPa (7.25 psi) T04
Leak test certificate*16 Retention time: one minute
*1: Not applicable with color change option. Not applicable for amplifier housing code 2.
*2: Check terminals cannot be used when this option code is specified. Not applicable for output signal code F and G and
amplifier housing code 2.
*3: Applicable for Wetted parts material code S.
*4: The unit of MWP (Max. working pressure) on the name plate of a housing is the same unit as specified by option codes D1,
D3, and D4.
*5: Applicable for vertical impulse piping type (Installation code 7) and Wetted parts material code S.
*6: Applicable for output signal codes D, E and J. The hardware error indicates faulty amplifier or capsule.
*7: Applicable for wetted parts material code S; process connection codes 3, 4, and 5; installation code 9; and mounting
bracket code N. Process connection faces on the other side of zero adjustment screw.
*8: Also see ‘Ordering Information’.
*9: Not applicable for amplifier housing code 2 and 3.
*10: 316 or 316L SST. The specification is included in amplifier housing code 2.
*11: Applicable only for output signal code E and J.
*12: The change of pressure fluctuation is monitored and then detects the impulse line blockage. See TI 01C25A31-01E for
detailed technical information required for using this function. The detection is for one side only.
*13: Material traceability certification, per EN 10204 3.1B.
*14: Applicable for process connections codes 0 and 5.
*15: Applicable for process connections codes 1, 2, 3, and 4.
*16: The unit on the certificate is always Pa unit regardless of selection of option code D1, D3 or D4.
*17: Pure nitrogen gas is used for oil-prohibited use (option codes K1 and K5).

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN Mar. 11, 2019-00
<<Contents>> <<Index>> 9
 DIMENSIONS
Unit: mm (approx.inch)

● Vertical Impulse Piping Type (INSTALLATION CODE ‘7’)

Electrical connection
for code 5, 9, A, and D.

54 (0.24)
6
256(10.10) 110(4.33)
194(7.64)

(2.13)
97 143(5.63) 12 39
(1.54) 2-inch pipe
(3.82) (0.47)
(O.D. 60.5 mm)

Mounting bracket Extenal indicator

Conduit connection Vent/Drain plugs
(2.05)

(L-type,optional)
52

(optional)
Integral indicator
(optional)
102(4.02)
234(9.21)

ø78(3.07)

148(5.83)*2
(3.74)

(2.76)
95*4

ø70
(1.81)
72(2.83)
46

Process
Conduit connector
connection (optional)
Process connection 54
41.3 Zero adjustment High Low
pressure (2.13) pressure
(1.63) Ground terminal side*1 side*1 F03E.ai

● Horizontal Impulse Piping Type (INSTALLATION CODE ‘9’)

(For CODE ‘8’, refer to the notes below.)

Extenal indicator Conduit connection

Conduit connection 94(3.70) 72(2.83) 110(4.33)
Zero
(optional) Integral adjustment
95(3.75)*4 indicator 12 39
(optional) (0.47) (1.54)
ø78(3.07)

54
(2.13) (2.76)
ø70
6
159(6.26)

(0.24) 143(5.63)
194(7.64)

(1.63)
41.3

Ground terminal

Electrical connection Vent plug

for code 5, 9, A, and D. Vent plug
Process Drain plug
124(4.88)

46 connection Drain plug

(1.81) Process 54
125(4.92) connector (2.13)
(optional)
2-inch pipe
(1.85)
47

(O.D. 60.5 mm)

Mounting bracket
(Flat-type,optional)

133*3
(5.24) F04E.ai

*1: When installation code 8 is selected, high and low pressure side on above figure are reversed.
(i.e. High pressure side is on the right side.)
*2: When option code K1, K2, K5 or K6 is selected, add 15 mm (0.59 inch) to the value in the figure.
*3: When option code K1, K2, K5 or K6 is selected, add 30 mm (1.18 inch) to the value in the figure.
*4: When electrical connection code 7 or C is selected, a blind plug is protruded upto 8 mm from the conduit connection.

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN Mar. 11, 2019-00
<<Contents>> <<Index>> 10
Unit: mm (approx.inch)
● Universal Flange (INSTALLATION CODE ‘U’)

External indicator 63 72 Zero 110(4.33)

Conduit connection adjustment
Conduit connection (2.48) (2.83)
12 39
(optional) 95(3.74)*2 Integral indicator
(0.47) (1.54)
54 (optional)

ø78(3.07)
(2.13)
6

(2.76)
ø70
(0.24) 159(6.26)

143(5.63)
194(7.64)
Ground terminal

Electrical connection
for code 5, 9, A, and D.

(1.63)
41.3
Vent plug
Drain plug
46 Drain plug
54
Vent plug (1.81) High (2.13) Low
Process connection pressure pressure
125(4.92) side 133(5.24)*1 side
Drain plug Process connector (optional) F05E.ai

*1: When Option code K1, K2, K5, or K6 is selected, add 30 mm (1.18 inch) to the value.
*2: When electrical connection code 7 or C is selected, a blind plug is protruded upto 8 mm from the conduit connection.

● Terminal Configuration ● Terminal Wiring

+ 1
Power supply and output terminals
SUPPLY – 2

CHECK + 3 External indicator (ammeter) terminals*1*2

– 2
or or
+ 3 Status contact output terminals*2
ALARM – 2 (when /AL is specified)
Ground terminal
*1: When using an external indicator or check meter, the internal
resistance must be 10 Ω or less. A check meter or indicator
cannot be connected when /AL option is specified.
Terminal 1 Terminal 3 *2: Not available for FOUNDATION Fieldbus and PROFIBUS PA
Terminal 2 communication types.
F06E.ai

● Wiring Example for Analog Output and Status Output

Connection Description
Analog output EJX electrical terminal
Distributor

+ + 24V DC
SUPPLY
– 250Ω
*1
CHECK A *1: Either A or + –

Analog and EJX electrical terminal Distributor

status output Shielded cable
+ 24V DC
(when /AL is specified) SUPPLY +

– – 250Ω
If shield cable is not
*1
used, communication ALARM A
is not possible. *1: Either A or +
Magnetic
External power supply valve
30V DC, 120mA max

Use two-wire separately shielded cables.

AC power supply
F07E.ai

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN Mar. 11, 2019-00
<<Contents>> <<Index>> 11

< Ordering Information > “◊” < Factory Setting > “◊”
Specify the following when ordering
Tag number As specified in order
For output signal code –J, refer to GS 01C25T01-
01EN. Software
‘2.00 s’ or as specified in order
damping *1
1. Model, suffix codes, and option codes
Output mode ‘Linear’ unless otherwise specified in order
2. Calibration range and units
1) Calibration range can be specified with range Calibration range
As specified in order
lower range value
value specifications up to 5 digits (excluding
any decimal point) for low or high range limits Calibration range
upper range As specified in order
within the range of -32000 to 32000. When
value
reverse range is designated, specify Lower
Range Value(LRV) as greater than Upper Range Selected from mmH2O, mmH2O(68°F),
mmAq*2, mmWG*2, mmHg, Pa, hPa*2,
Value(URV). When square root output mode is Calibration range kPa, MPa, mbar, bar, gf/cm2,
specified, LRV must be “0 (zero) ”. unit kgf/cm2, inH2O, inH2O(68°F), inHg, ftH2O,
2) Specify only one unit from the table, ‘Factory ftH2O(68°F) or psi. (Only one unit can be
setting.’ specified.)
3. Select linear or square root for output mode and Designated differential pressure value
display mode. specified in order. (% or user scaled
Note: If not specified, the instrument is shipped set for Display setting
value.) Display mode ‘Linear’ or ‘Square
linear mode. root’ is also as specified in order.
4. Display scale and units (for transmitters equipped
with the integral indicator only) *1: To specify these items at factory, option code CA
Specify either 0 to 100 % or ‘Range and Unit’ for or CB is required.
engineering units scale: *2: Not available for HART protocol type.
Scale range can be specified with range limit
specifications up to 5 digits (excluding any decimal < Material Cross Reference >
point) for low or high range limits within the range
of -32000 to 32000. Unit display consists of 6-digit, ASTM JIS
therefore, if the specified scaling unit excluding ‘/’ is 316 SUS316
longer than 6-characters , the first 6 characters will F316 SUSF316
be displayed on the unit display. 316L SUS316L
5. Tag Number (if required) F316L SUSF316L
Specified characters (up to 16 characters for 304 SUS304
BRAIN, 22 characters for HART, or 16 characters
F304 SUSF304
for /N4 tag) are engraved on the stainless steel tag
plate fixed on the housing. 660 SUH660
6. SOFTWARE TAG (for HART only. if required) B7 SNB7
Specified characters (up to 32 characters) are set CF-8M SCS14A
as “Tag” (the first 8 characters) and “Long tag”*1
(32 characters) in the amplifier memory. Use
alphanumeric capital letters. < Information on EU WEEE Directive >
When the “SOFTWARE TAG” is not specified, EU WEEE (Waste Electrical and Electronic Equipment)
specified “TAG NO” is set as “Tag” (the first 8 Directive is only valid in the EU.
characters) and “Long tag”*1 (22 characters) in the This instrument is intended to be sold and used only
amplifier memory. as a part of equipment which is excluded from WEEE
*1: applicable only when HART 7 is selected. Directive, such as large-scale stationary industrial
7. Other factory configurations (if required) tools, a large-scale fixed installation and so on, and,
Specifying option code CA or CB will allow further therefore, subjected to the exclusion from the scope
configuration at factory. Following are configurable of the WEEE Directive. The instrument should be
items and setting range. disposed of in accordance with local and national
[/CA : For HART communication type] legislation/regulations.
1) Descriptor (up to 16 characters)
2) Message (up to 30 characters)
3) Software damping in second (0.00 to 100.00)
[/CB : For BRAIN communication type]
1) Software damping in second (0.00 to 100.00)

All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 01C25B03-01EN Mar. 11, 2019-00
Subject to change without notice.