Scribd
Upload
1K views

Basic Electronics (18ELN14/18ELN24) - Silicon Controlled Rectifier (Module 2)

Lecture Notes for Basic Electronics (18ELN14/18ELN24) - Silicon Controlled Rectifier (Module 2) for VTU Students Contents: Silicon Controlled Rectifier (SCR) – Two-transistor model, Switching action, Characteristics, Phase control application.

Uploaded by

Shrishail Bhat
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Basic Electronics (18ELN14/18ELN24) - Silicon Controlled Rectifier (Module 2)

Lecture Notes for Basic Electronics (18ELN14/18ELN24) - Silicon Controlled Rectifier (Module 2) for VTU Students Contents: Silicon Controlled Rectifier (SCR) – Two-transistor model, Switching action, Characteristics, Phase control application.

Uploaded by

Shrishail Bhat
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Basic Electronics Silicon Controlled Rectifier (SCR)

Silicon Controlled Rectifier (SCR)


Topics Covered from Module 2: Silicon Controlled Rectifier (SCR) – Two-transistor model,
Switching action, Characteristics, Phase control application.

Introduction
A silicon controlled rectifier (SCR) is a switching device widely used in power control
applications. It is a four-layer device with three terminals – anode (A), cathode (K) and gate (G).
SCR has a wide range of applications including rectifiers, regulated power supplies, dc to ac
conversion (inverters), relay control, time-delay circuits and many more.

Basic Operation and Symbols


SCR is made of silicon because of high temperature requirement of handling large current
and power. Its four layers are PNPN as shown in Fig. 1 (a). The outer p-layer is connected to
anode terminal and outer n-layer is connected to cathode terminal. The p-layer closer to the
cathode is connected to the gate terminal. The symbol of an SCR is as shown in Fig. 1 (b).

Fig. 1 Silicon controlled rectifier (SCR)


When a forward voltage is applied across the anode and cathode, no conduction takes
place as the middle pn-junction is reverse biased. If a positive pulse is applied at the gate, such
that a current of magnitude equal to or more than 𝐼𝐺(𝑡𝑢𝑟𝑛−𝑜𝑛) flows into the gate, the SCR turns
on and conducts. However, because of regenerative action, removing the gate current does not
cause the device to turn off.

Two-Transistor Model
The basic operation of an SCR can be best explained by splitting the four-layer PNPN
structure into two three-layer structures as shown in Fig. 2 (a). The resultant two-transistor
circuit model is shown in Fig. 2 (b).

Fig. 2 Two-transistor model of SCR

Shrishail Bhat, Dept. of ECE, AITM Bhatkal www.shrishailbhat.com 1


Silicon Controlled Rectifier (SCR) Basic Electronics
According to this model, the SCR comprises of two transistors – one PNP transistor and
one NPN transistor. The base of PNP is connected to the collector of NPN and the collector of PNP
is connected to the base of NPN. The gate is connected to the base of NPN.

Switching Action (Operation)


Let a positive voltage 𝑉 be applied to the anode (𝐸1 ) and let the cathode (𝐸2 ) and gate (𝐺)
be both grounded as shown in Fig. 3 (a).

Fig. 3 Switching action of SCR


As 𝑉𝐺 = 𝑉𝐵𝐸2 = 0, the transistor 𝑇2 is in OFF state. It means that the collector-base
junction of 𝑇2 , through emitter-base junction of 𝑇1 , is reverse biased. Therefore 𝐼𝐵1 = 𝐼𝐶𝑂
(leakage current due to minority charge carriers) is too small to turn-on 𝑇1 . Thus both 𝑇1 and 𝑇2
are OFF and hence the anode current 𝐼𝐴 = 𝐼𝐵1 = 𝐼𝐶𝑂 is of negligible order. This means that SCR is
in OFF state, that is, the switch between anode (𝐸1 ) and cathode (𝐸2 ) is open.
Now, let a voltage 𝑉𝐺 > 0 be applied at the gate as shown in Fig. 3 (b). As 𝑉𝐵𝐸2 = 𝑉𝐺 , when
𝑉𝐺 is sufficiently large, 𝐼𝐵2 will cause 𝑇2 to turn on and the collector current 𝐼𝐶2 becomes large. As
𝐼𝐵1 = 𝐼𝐶2 , 𝑇1 turns on causing a large collector current 𝐼𝐶1 (𝐼𝐴 = 𝐼𝐶1 ) to flow. This is turn, increases
𝐼𝐵2 causing a regenerative action to set in. As a result, the SCR is turned ON, that is, the switch
between anode (𝐸1 ) and cathode (𝐸2 ) is closed.
The turn-on time of an SCR is typically 0.1 to 1 µs. However, for high-power devices, the
turn-on time may be 10 to 25 µs.

Turn-OFF (Commutation)
Once the SCR is turned ON, it cannot be turned OFF by simply removing the gate signal.
The mechanism of turning OFF an SCR is called commutation. There are two types of
commutation – natural commutation and forced commutation.

Natural Commutation
When the source that feeds the current to anode of SCR is such that it passes through
zero, the SCR turns off at the current zero. This is the case when the SCR is fed from an ac source.
This is known as natural commutation or line commutation.

Forced Commutation

2 www.shrishailbhat.com Shrishail Bhat, Dept. of ECE, AITM Bhatkal


Basic Electronics Silicon Controlled Rectifier (SCR)
In this method, the current through the SCR is forced to become zero by passing a current
through it in opposite direction from an independent circuit. A variety of circuits are available
for forced commutation. Fig. 4 shows a basic turn-off circuit.

Fig. 4 SCR turn-off (commutation) circuit


A transistor and a dc battery source in series are connected to the SCR. When the SCR is
in conduction mode (ON) and 𝐼𝐵 = 0, the transistor is off and it is almost an open circuit. To turn
off the SCR, a positive pulse (𝐼𝐵 ) of magnitude large enough to drive the transistor into saturation
is applied at the transistor base. The transistor acts almost like a short circuit. This causes flow
of very large current 𝐼𝑜𝑓𝑓 through the SCR in the direction opposite to its conduction current.
The total SCR current reduces to zero in a very short time causing it to turn OFF.
The turn-off time of an SCR is typically 5 to 30 µs.

SCR Characteristics
The symbol and V-I characteristics of SCR for different values of gate current are shown
in Fig. 5.

(a) Symbol

(b) V-I characteristics

Fig. 5 SCR characteristics


Various parameters of importance are described below:
Shrishail Bhat, Dept. of ECE, AITM Bhatkal www.shrishailbhat.com 3
Silicon Controlled Rectifier (SCR) Basic Electronics
i) Forward Breakover Voltage 𝑽𝑭(𝑩𝑹) : It is the voltage at which, for a given 𝐼𝐺 , the SCR
enters into conduction mode. This voltage reduces as 𝐼𝐺 increases.
ii) Holding Current (𝑰𝑯 ): It is the value of the anode current below which SCR switches
from conduction state to forward blocking region.
iii) Latching Current (𝑰𝑳 ): It is the minimum value of the anode current required to keep the
SCR turned ON after removing the gate signal. Latching current is larger than holding
current.
iv) Forward Conduction Region: It is the region in which SCR is ON (short circuited) and is
in conduction mode. In this region, the SCR conducts forward current from anode to
cathode.
v) Forward and Reverse Blocking Region: These are the regions in which the SCR is OFF
(open circuited) and no current flows from anode to cathode.
vi) Reverse Breakdown Voltage: It is the reverse anode to cathode voltage at which Zener
or avalanche breakdown of the device takes place and the current rises abruptly.

Applications of SCR
SCR is widely used in power control applications. It has a wide range of applications
including rectifiers, regulated power supplies, dc to ac conversion (inverters), relay control,
time-delay circuits and many more.

Variable Resistance Phase Control


An SCR can be used to control the phase of an ac signal by using a variable resistance. It
is an effective method of controlling the rms value of the current and thereby power delivered
to the load.
On triggering, an SCR permits flow of only forward current, but blocks the current in
reverse direction. This action is similar to that of a diode, but an SCR needs to be triggered for
each positive half cycle. It then produces a constant dc (average) current through load and dc
voltage across load. By adjusting the triggering time on positive half cycle of ac voltage, we can
get variable dc output. This method is known as phase control.

(c) Firing angle 𝛼 < 90°

Fig. 6 Variable resistance phase control using SCR

4 www.shrishailbhat.com Shrishail Bhat, Dept. of ECE, AITM Bhatkal


Basic Electronics Silicon Controlled Rectifier (SCR)
A variable resistance phase control circuit is shown in Fig. 6. The triggering circuit
consists of a diode 𝐷, a fixed resistor 𝑅 and a variable resistor 𝑅1 . The combination of 𝑅 and 𝑅1
limits the gate current during positive half cycle of the input. The diode 𝐷 prevents the flow of
reverse gate current during negative cycle of the input.
Let 𝑅1 be adjusted to high value, so that even at the peak value 𝑣𝑖 , 𝐼𝐺 < 𝐼𝐺(𝑡𝑢𝑟𝑛−𝑜𝑛) and no
conduction takes place. As 𝑅1 is reduced, 𝐼𝐺 rises to turn-on value at a particular angle of 𝑣𝑖 . The
conduction then begins and continues till 𝑣𝑖 reaches zero (180°). The firing angle of SCR can be
adjusted by varying 𝑅1 .
At 𝑅1 corresponding to the firing angle of 90°, 𝑣𝑖 = 𝑣𝑖(max) . If 𝑅1 is adjusted for firing at
𝛼, the firing will take place at angle 𝛼 < 90°, but not at 𝛽 = (180° − 𝛼) > 90° as the angle 𝛼 is
reached earlier in time on the 𝑣𝑖 wave. So, the operation of this circuit is known as half-wave
variable resistance phase control.

Questions
1. What is SCR? Explain the working of SCR using two-transistor model.
(Sep ’20 – 8M, Jan ‘20 – 6M, Jul ‘19 – 6M, MQP ’18 – 6M)
2. Draw and explain the operation of SCR using two-transistor equivalent circuit.
(MQP ’18 – 8M)
3. Using the two-transistor model, explain the switching action of SCR.
4. What is commutation in SCR? Explain two types of commutation. (Jul ‘19 – 5M)
5. Explain natural and forced commutation turn off methods of SCR. (Sep ’20 – 6M)
6. Draw and explain the V-I characteristics of SCR. (Jan ‘19 – 6M, MQP ’18 – 6M)
7. Explain phase control application of SCR. (MQP ’18 – 6M)

References
1. D.P. Kothari, I. J. Nagrath, “Basic Electronics”, McGraw Hill Education (India) Private
Limited, Second Edition, 2014.
2. Thomas L. Floyd, “Electronic Devices”, Pearson Education, Ninth Edition, 2012.

Shrishail Bhat, Dept. of ECE, AITM Bhatkal www.shrishailbhat.com 5

You might also like