CNC

PROGRAM MANUAL

PU
MA
450

www.EngineeringBooksPdf.com
TRAINING

Forward

Thank you very much for participating in our education.

DAEWOO constantly makes an effort to research and develop to satisfy the

requirements of customers positively.
DAEWOO does its utmost to accept and practice the Quality Confirmation of DAEWOO and Custom-
ers' requirements through the Dealer-net-work of about 350 as practicing the World Quality Manage-
ment.
DAEWOO provides with the technical data and support the technical coaching, therefore, if you con-
tact us when you need of them , we will immediately help you.

We will do our best during your education period.

Thank you.

www.EngineeringBooksPdf.com
TRAINING

O-T

DAEWOO
RESET O( N) GE RC 7 8 9 ALTER
NO. X Z R
G 01 0.000 0.000 0.000
NC POWER G 02 0.000 0.000 0.000 XU YV Z W 4TH 4 5 6 INSRT

0.000 0.000 0.000 CURSOR

G 03
ON G 04 0.000 0.000 0.000 I ,
JA K@ F-NO 1 2 3 DELET

G 05 0.000 0.000 0.000

G 06 0.000 0.000 0.000
M# S= T* L+ _ .
G 07 0.000 0.000 0.000

ACT. POSITION(RELATIVE) P[ Q] DH BSP EOB CAN INPUT

U 0.000 W 0.000
PAGE
NUM. MZ 120. S MDI 0T
OFF SHIFT POS PRGRM OFSET MENU

WEAR GEOM W.SHIFT MRCRO DGNOS OPR AUX OUTPT

MACRO
PARAM ALARM GRAPH START

? ? N LM
80 100 120 90 100 110
50 100 150
60 140 80 120 0 180

40
150
70
? %
20 60
0 50 ALARM NO.
SPINDLE LOAD
FEEDRATE OVERRIDE SPINDLE OVERRIDE SPINDLE SPEED
EMERGENCY STOP

+X

X100

X X10
–Z +Z
SINGLE OPTIONAL OPTIONAL DRY RUN
Z START STOP COOLANT BLOCK STOP BLOCK SKIP
X1

MODE INCREMENTAL FEED

RAPID N β

α
6 7 8
100 45 9
3 10
50 2 11
–X 1 12
F0
CYCLE START FEED HOLD MACHINE READY EMG. RELEASE RAPID OVERRIDE TOOL NO. MACHINE LOCK PROGRAM PROTECT CHUCKING

www.EngineeringBooksPdf.com
TRAINING
G-FUNCTION

STANDARD G SPECIAL
GROUP FUNCTION
CODE G CODE

#G00 G00 01 Positioning (Rapid feed)

G01 G01 Straight interpolation
G02 G02 Circular interpolation (CW)
G03 G03 Circular interpolation (CCW)

G04 G04 00 Dwell

G20 G20 06 Data input (inch)

#G21 G21 Data input (mm)

#G22 G22 04 Stored distance limit is effective

G23 (Spindle interference check ON)
G23 Stored distance limit is ineffective
(Spindle interference check OFF)

G27 G27 00 Machine reference return check

G28 G28 Automatic reference return
G29 G29 Return from reference
G30 G30 Tte 2nd rererence return

#G32 G33 01 Thread process

G40 G40 07 Cancel of compensation

G41 G41 Compensation of the left
G42 G42 Compensation of right

G50 G92 00 Creation of virtual coordinate/Setting the rotating time of principal spindle
G70 G70 Compound repeat cycle(Finishing cycle)
G71 G71 Compound repeat cycle(Stock removal in turning)
G72 G72 Compound repeat cycle(Stock removal in facing)
G73 G73 Compound repeat cycle(Pattern repeating cycle)
G74 G74 Compound repeat cycle(Peck drilling in Z direction)
G75 G75 Compound repeat cycle(Grooving in X direction)
G76 G76 Compound repeat cycle(Thread process cycle)

G90 G77 01 Fixed cycle(Process cycle in turning)

G92 G78 Fixed cycle(Thread process cycle)
G94 G79 Fixed cycle(Facing process cycle)

G96 G96 02 Control the circumference speed uniformly(mm/min)

#G97 #G97 Cancel the uniform control of circumference speed.
Designate r.p.m

G98 G94 05 Designate the feedrate per minute(mm/min)

#G99 #G95 Designate the feedrate per the rotation of principal spindle(mm/rev.)

- G90 03 Absolute programming

- G91 Incremental programming

Note) 1. # mark instruction is he modal indication of initial condition which is immediately available
when power is supplied.
2. In general, the standard G code is used in lathe, and it is possible to select the special G code
according to setting of parameters.

www.EngineeringBooksPdf.com
TRAINING

NC LATHE M-CODE LIST

M-CODE DESCRIPTION REMARK M-CODE DESCRIPTION REMARK

M00 PROGRAM STOP M39 STEADY REST 1 UNCLAMP OPTION

M01 OPTIONAL STOP M40 GEAR CHANGE NETURAL
M02 PROGRAM END M41 GEAR CHANGE LOW
M03 MAIN-SPINDLE FORWARD M42 GEAR CHANGE MIDDLE
M04 MAIN-SPINDLE REVERSE M43 GEAR CHANGE HIGH
M05 MAIN-SPINDLE STOP M46 PTS BODY UNCL & TRACT-BAR ADV. OPTION
M07 HIGH PRESSURE COOLANT ON OPTION M47 PTS BODY CL & TRACT-BAR RET. OPTION
M08 COOLANT ON M50 BAR FEEDER COMMAND 1 OPTION
M09 COOLANT OFF M51 BAR FEEDER COMMAND 2 OPTION
M10 PARTS CATCHER ADVANCE OPTION M52 SPLASH GUARD DOOR OPEN OPTION
M11 PARTS CATCHER RETRACT OPTION M53 SPLASH GUARD DOOR CLOSE OPTION
M13 TURRET AIR BLOW OPTION M54 PARTS COUNT OPTION
M14 MAIN-SPINDLE AIR BLOW OPTION M58 STEADY REST 2 CLAMP OPTION
M15 AIR BLOW OFF OPTION M59 STEADY REST 2 UNCLAMP OPTION
M17 MACHINE LOCK ACT (ONLY)
MDI M61 SWITCHING LOW SPEED (N.J) α P60
M18 MACHINE LOCK CANCEL (ONLY)
MDI
M62 SWITCHING HIGH SPEED (N.J) α P60
M19 MAIN-SPINDLE ORIENTAION OPTION M63 MAIN-SPDL CW & COOLANT ON
M24 CHIP CONVEYOR RUN OPTION M64 MAIN-SPDL CCW & COOLANT OFF
M25 CHIP CONVEYOR STOP OPTION M65 MAIN-SPDL & COOLANT OFF
M30 PROGRAM END & REWIND M66 DUAL CHUCKING LOW CLAMP OPTION
M31 INTERLOCK BY-PASS(SPDL &T/S) M67 DUAL CHUCK HIGH CLAMP OPTION
M32 INTERLOCK BY-PASS(SPDL &S/R) 3 AXIS M68 MAIN-CHUCK CLAMP
M33 REV.-TOOL-SPINDLE FORWARD 3 AXIS M69 MAIN-CHUCK UNCLAMP
M34 REV.-TOOL-SPINDLE REVERSE M70 DUAL TAILSTOCK LOW ADVANCE OPTION
M35 REV.-TOOL-SPINDLE STOP M74 ERROR DETECT ON
M38 OPTION M75 ERR0R DETECT OFF

www.EngineeringBooksPdf.com
TRAINING

NC LATHE M-CODE LIST

M-CODE DESCRIPTION REMARK M-CODE DESCRIPTION REMARK

M76 CLAMFERING ON M131 INTERLOCK BY-PASS (SUB-SPDL)

M77 CLAMFERING OFF M163 SUB-SPDL CW & COOLANT ON
M78 TAILSTOCK QUILL ADVANCE M164 SUB-SPDL CCW & COOLANT OFF
M79 TAILSTOCK QUILL RETRACT M165 SUB-SPDL & COOLANT STOP
M80 Q-SETTER SWING ARM DOWN OPTION M168 SUB-CHUCK CLAMP
M81 Q-SETTER SWING ARM UP OPTION M169 SUB-CHUCK UNCLAMP
M84 TURRET CW ROTATION M203 FORWARD SYNCHRONOUS COM.
M85 TURRET CCW ROTATION M204 REVERSE SYNCHRONOUS COM.
M86 TORQUE SKIP ACT B AXIS M205 SYNCHRONOUS STOP
M87 TORQUE SKIP CANCEL B AXIS M206 SPINDLE ROTATION RELEASE
M88 SPINDLE LOW CLAMP
M89 SPINDLE HIGH CLAMP
M90 SPINDLE UNCLAMP
M91 EXTERNAL M91 COMMAND 3 AXIS
M92 EXTERNAL M92 COMMAND 3 AXIS
M93 EXTERNAL M93 COMMAND
M94 EXTERNAL M94 COMMAND OPTION
M98 SUB-PROGRAM CALL OPTION
M99 END OF SUB-PROGRAM OPTION
M103 SUB-SPINDLE FORWARD
M104 SUB-SPINDLE REVERSE
M105 SUB-SPINDLE STOP
M110 PARTS CATCHER ADVANCE(SUB) OPTION
M111 PARTS CATCHER RETRACT(SUB) OPTION
M114 SUB-SPINDLE AIR BLOW OPTION
M119 SUB-SPINDLE ORIENTATION OPTION

www.EngineeringBooksPdf.com
TRAINING
Note) 1. M00 : For this command, main spindle stop, cutting oil, motor stop, tape reading stop are
carriedout.
M01 : While this function is the same as M00, it is effective when the optional stop switch of
console is ON.
This command shall be overrided if the optional stop switch is OFF.
M02 : Indicates the end of main program.
M30 : This is the same as M02 and it returns to the starting position of the programme when
the memory and the tape are running.

2. M code should not be programmed in the command paragraph containing S code or T code.
It is favorable for M code to programe in a command paragraph independently.

3. The edges of processed material become round due to the effect of characteristics of AC
servo motor. To avoid it, M74 and M75 functions are used.

When command of M75 When command of M74

(Error detection is OFF) (Error detection is ON)

4. M76, M77
These codes are effective when thread process is programmed by G92, and they are used for
ON and OFF of thread beveling. Thread chamferingis set as much as one pitch by setting of
parameters and it is possible to set double.

(Thread chamferingON) (Thread chamferingOFF)

www.EngineeringBooksPdf.com
TRAINING

Function Address Meaning of address

Program number O(EIA)/(ISO) Program number
Block sequence number N Sequence number
Preparatory function G Sercifies a motion mode (Linear, arc, etc)
Dimension word X, Z Command of moving position(absolute type) of each axis

U, W Instruction of moving distance and direction(incremental type)

I, K Ingredient of each axis and chamfering volume of circulat center

R Radius of circle, corner R, edge R

Feed function F, E Designation of feedrate and thread lead
Auxiliary function M Command of ON/OFF for operating parts of machine
Spindle speed function S Designation of speed of main spindle or rotation time of main spindle
Function (Tool) T Designation of tool number and tool compensation number
Dwell P, U, X Designation of dwell time
Dewignation of program number P Designation of calling number of auxiliary program
Designation of sequence No P, Q Callling of compound repeat cycle, end number
Number of repetitions L Repeat time of auxiliary program
Parameters A, D, I, K Parameter at fixed cycle

One block is composed as follows

One block

N G X Y F S T M :
Sequence Preparation Dimension Feed Spindle Tool Function EOB
Auxiliary function word function speed function auxiliary
No. function

www.EngineeringBooksPdf.com
TRAINING
Meaning of Address
T function is used for designation of tool numbers and tool compensation.
T function is a tool selection code made of 4 digits.
T 0 2 0 2
Designation of tool compensation number
Designation of tool number

Example) If it is designated as(T 0 2 0 2 )

0 2 calls the tool number and calls the tool compensation value of number , and
the tool is compensation as much as momoried volume in the storage.
The cancel of tool compensation is commanded as T 0 0
If you want to call the next tool and compensation, you should cancel the tool com-
pensation. For convenient operation, it is recommended to used the same number of
tool and compensation.
It is not allowed to use the same tool compensation number for 2 different tools.

Minimum compensation value : + 0.001mm

Maximum compensation value : + 999.999mm
Tool compensation of X spindle is designated as diameter value.

www.EngineeringBooksPdf.com
TRAINING
G00(Positioning)

G00 Each axes moves as much as commanded data in rapid feedrate.

G00 X(U) Z(W); G00 X150.0 Z100.0

X200.0 Z200.0
X
X200
X150 Z200 G00 U150.0 W100.0
Z100
Z U50.0 W100.0
(X0 Z0)

N1234 G00 X25. Z5.

+X

G00

-Z +Z

Ø25

-X

www.EngineeringBooksPdf.com
TRAINING

G01
G01(Linear interpolation)
Each axes moves straigrtly as much as commanded data in commanded rate.

G01 X150.0 Z100.0 F0.2 :

G01 X(U) Z(W) F X200.0 Z200.0 :
X
X200 G01 U150.0 W100.0 F0.2 :
X150 Z200
Z100 U50.0 W100.0 :
Z
(X0 Z0)

N1234 G01 X25. Z-30. F0.2

+X

G01

-Z +Z

Ø25

30

-X

www.EngineeringBooksPdf.com
TRAINING
AUTO CHAMFERING “C” AND CORNER “R” (Option)
+X

C
+r
+i
A
B
-i Command path Z→X : A : Start point of instuction
-r
C' G01 Z(w) B C ( ¡ i) : B : End point of instruction
-X G01 Z(w) B C ( ¡ r) :CC’ : Running point of command
A

-r +r
Command path X→Z :

-Z +Z G01 X(u) B C ( ¡ k)
C' B C
-K +K G01 X(u) B R ( ¡ r)

Note) (1) After instructing from G01 to one axis, the next command paragraph should be fed in
vertical direction.
(2) If the next command paragraph is incremental type, designate the incremental volume
baed on B point.
(3) In following cases, errors occur. (G01 Mode)
– When instruction one of I, K, R and X and Z at the same time.
– When instructing two of I, K, R in the same block.
– When instructing Xand I or Z and K.
– When the moving distance is less than the next command
are not right angled.
(4) During the operation of single command paragraph, the operation at C point stops.

Example)
X
C3 N1 G01 Z30.0 R6.0 F0.2 :
N3
N2 N2 X100.0 K-3.0 :
6
R

N1
N3 Z0 :
Ø100

Z
Ø40

(N2 X100.0 C3.0 :)Normal

30

80

10

www.EngineeringBooksPdf.com
TRAINING
G01 PROGRAM
Example1)

Ø100

Ø80
50 30 15
O0001 :
N10 G50 S1500 T0100 M42 : N20 G50 S2000 T0300 :
G96 S180 M03 : G96 S200 M03 :
G00 X100.5 Z5.0 T0101 M08 : G00 X85.0 Z5.0 T0303 M08 :
G01 Z-95.0 F0.25 : Z0 :
G00 U2.0 Z0.5 : G01 X-1.6 F0.2 :
G01 X-1.6 F0.2 : G00 X80.0 Z3.0 :
G00 X95.0 W1.0 : G42 Z1.0 :
G01 Z-37.3 F0.25 : G01 Z-15.0 F0.18 :
X100.0 Z-45.5 : X100.0 Z-45.0 :
G00 Z1.0 : Z-95.0 :
X90.0 : G40 U2.0 W1.0
G01 Z-29.8 : G00 X200.0 Z200.0 M09 T0300 :
X95.0 Z-37.3 : M30 :
G00 Z1.0 :
X85.0 : G50 : Setting the rotating time of max. speed of
G01 Z-22.3 : main spindle
X90.0 Z-29.8 : G96 : Constant surface speed control command
G00 Z1.0 : G40 : Compensation cancel
X80.5 : G42 : Right hand compensation
G01 Z-15.55 :
X85.0 Z-22.3 :
G00 X200.0 Z200.0 M09 T0100 :
M01 :

11

www.EngineeringBooksPdf.com
TRAINING
G01 PROGRAM
Example2)
C1
C1

Ø60
Ø70

Ø50
45 25 30
100

O0002 : G01 Z-30.0 :

X60.3 Z-54.7 :
N10 G50 S2000 T0100 :
X72.0
G96 S180 M03 :
G00 X150.0 Z200.0 T0100 :
G00 X70.5 Z5.0 T0101 M08 :
M01 :
G01 Z-100.0 F0.25 :
N20 G50 S2300 T0300 :
G00 U2.0 Z0.5 :
G96 S200 M03 :
G01 X-1.6 F0.23 :
G00 X55.0 Z5.0 T0303 M08 :
G00 X65.0 W1.0 : Z0 :
G01 Z-54.5 F0.25 : G01 X-1.6 F0.2 :
G00 U2.0 Z1.0 : G00 X46.0 Z3.0 :
X60.0 : G42 Z1.0 :
G01 Z-54.5 : G01 X50.0 Z-1.0 F0.15 :

G00 U2.0 Z1.0 : Z-30.0 :

X55.0 : X60.0 Z-55.0 :

X68.0 :
G01 Z-30.0 :
X70.0 W-1.0 :
X60.0 Z-54.5 :
Z-100.0 :
G00 U2.0 Z1.0 :
G40 U2.0 W1.0
X50.5 :
G00 X150.0 Z200.0 M09 T0300 :
M30 :

12

www.EngineeringBooksPdf.com
TRAINING

G02 G03
X I (X)

Z K(Z)
P0

P2
X

G02 I

P1

K
Z

N1234 G02 X.. Z.. (R..)

X
P2

G03

P1
P0 -I

-K
Z

N1234 G03 X.. Z.. (R..)

13

www.EngineeringBooksPdf.com
TRAINING
G02, G03(Circular interpolation)
Each axis interpolates circularly to the commanded coordinate in instructed speed.

Meaning
Conditions Instruction
Right hand coodinate Left hand coodinate
1 Rotation direction G02 CW CCW

G03 CCW CW
2 Location of end point X,Z Location X,Z of commanded point from coordinate
Distance to the end point U,W Distance from start point to commanded point
3 Distance between start point Distance from start point to the center of and arc
and the center point I,K with sign, radius value (I always designates the

radius)
Arc radius with no sign radius R Radius of circumference
of circumference

G02 X(u) Z(w) R_ F_ :

60 G01 X30.0 Z60.0 F0.3 :

X 30 Z35.0 :
5

G02 G02 X40.0 Z30.0 I5.0 :

R

G02 (G02 U10.0 W-5.0 I5.0)

Ø50

Z
Ø30

G01 X50.0 :
Z0 :

G03 X(u) Z(w) R_ F_ :

G01 X40.0 Z60.0 F0.3 :

X 60
G03 G03 X50.0 Z55.0 K-5.0 :
G03
5
R
Ø50

14

www.EngineeringBooksPdf.com
TRAINING
Note) (1) If I or K is 0 it is omissible.
(2) G02 I_: Make a round of circle.
(3) It is recommended to use R as + value, and designates the circumferences less than
180.
G03 R_: No moving
(4) When designating R which is less than the half of moving distance, override R and make
half circle.
(5) When designating I, K and R at the same time, R is effective.
(6) When the moving end point is not on the circumference as a result of wrong designation
of and K :

P2 P2
r r

P1 P1

15

www.EngineeringBooksPdf.com
TRAINING
G03 PROGRAM
G02
)
Example 1)

Ø100

Ø20
R4
5 20.615

40 24.385 50

N10 :

N20 G50 S2000 T0300 :

G96 S200 M03 :
G00 X0 Z3.0 T0303 M08 :
G42 G01 Z0 F0.2 :
G03 X20.0 Z-10.0 R10.0 :
G01 Z-50.0 :
G02 X100.0 Z-74.385 I40.0 K20.615 : (G02 X100.0 Z-74.385 R45.0)
G01 Z-125.0 :
G40 U2.0 W1.0
G00 X200.0 Z200.0 M09 T0300 :
M30 :

16

www.EngineeringBooksPdf.com
TRAINING
G02 PROGRAM
G03
)
Example 2)

16
16

R
Ø100
R

Ø35
46 36

N10 :

N20 G50 S2000 T0300 :

G96 S200 M03 :
G42 G00 X35.0 Z5.0 T0303 M08 :
G01 Z-20.0 F0.2 :
G02 X67.0 Z-36.0 R16.0 : (G02 X67.0 Z-36.0 I16.0 K0)
G01 X68.0 :
G03 X100.0 Z-52.0 R16.0 : (G02 X100.0 Z-52.0 I0 K-16.0)
G01 Z-82.0 :
G40 G00 X200.0 Z200.0 M09 T0300 :
M30 :

# When I and K instruction, if the data value is “0” it can be omitted.

17

www.EngineeringBooksPdf.com
TRAINING
G01
G02
G03
) PROGRAM
30
15
2.5

.5
R1
R3
Ø30

Ø35

Ø100
Ø102
Ø40
Ø60
Ø80
15
24.33
8 42

O0000 :
N10 (ø30 DRILL) G01 Z-14.8 F0.27 :

G50 T0200 : G00 U2.0 Z1.0 :

G97 S250 M03 : X80.5 :

G00 X0 Z5.0 T0202 M08 : G01 Z-14.1 :

G01 Z-5.0 F0.07 : G02 X81.9 Z-14.8 R0.7 :

W1.0 : G00 X100.5 W1.0

Z-40.0 F0.25 : G01 Z-29.8

G00 Z5.0 : G00 U2.0 Z-1.0 :

Z-39.0 : G01 X60.5 F0.23 :

G01 Z-60.0 : G00 X82.0 W1.0 :

G00 Z10.0 : Z-2.4 :

X200.0 Z200.0 T0200 : G01 X60.5 :

M01 : X72.9 :

N20 (Outside diameter stock removal) G03 X80.5 Z-6.2 R3.8 :

G50 S1500 T0100 : G00 U2.0 Z5.0 :

G96 S180 M03 : X200.0 Z200.0 T0100 :

G00 X94.0 Z5.0 T0101 M08 : M01 :

G01 Z-14.8 F0.27 :

G00 U2.0 Z0.5 :
G01 X28.0 F0.23 :
G00 X87.0 W1.0 :

18

www.EngineeringBooksPdf.com
TRAINING
N30 (Inside diameter stock removal) N50 (Inside diameter finishing)
G50 S1500 T0400 : G50 S1800 T0600 :
G96 S180 M03 : G96 S200 M03 :
G00 X34.5 Z3.0 T0404 M08 : G00 X40.0 Z5.0 T0606 M08 :
G01 Z-41.8 F0.27 : G41 Z1.0 :
G00 U-0.5 Z1.0 : G01 Z-15.0 F0.2 :
X39.5 : X35.0 Z-24.33 :
G01 Z-15.0 : Z-42.0 :
X34.5 Z-24.3 : X29.0 :
G00 Z10.0 : G40 G00 Z10.0 :
X200.0 Z200.0 T0400 : X200.0 Z200.0 T0600 M09 :
M01 : M30 :
N40 (Out diameter finishing)
G50 S1800 T0500 :
G96 S200 M03 :
G00 X63.0 Z5.0 T0505 M08 :
Z0 :
G01 X38.0 F0.2 :
G00 X60.0 Z3.0 :
G42 Z1.0 :
G01 Z-2.5 F0.2 :
X74.0 :
G03 X80.0 Z-5.5 R3.0 :
G01 Z-13.5 :
G02 X83.0 Z-15.0 R1.5 :
G01 X100.0 :
Z-30.0 :
X103.0 :
G40 G00 U2.0 W1.0 :
G00 Z10.0 :
X200.0 Z200.0 T0500 :
M01 :

19

www.EngineeringBooksPdf.com
TRAINING
1G04 (Dwell)

After passing as much time as commanded by X(u) or P code in the same block, carry out the next
block.
In case of 10 seconds' dwell
G04 X10.0 : (G04 X10000 : )
G04 U10.0 : (G04 U10000 : )
G04 P10000.0 : (G04 P1000 : )

Automatic reference return

Reference means certain point fixed in the machine, and coordinate value of reference is set in NC
parameter.
OT-C/F FS16/18T
Parameter NO N708(X) N1240(X, Z)
N709(Z)
1) G27(Reference return check)
Position is decided through rapid feed to the position of value set in NC PARAMETER by com-
mand.

Example) When PARAMETER N708(X) is 330000

N709(Z) is 529000

G00 X100.0 Z100.0 :

G27 X330.0 Z529.0 : End point(Machine reference)
X330.0
( )
X100.0 Z529.0
( )
Z100.0
Start point(0.0)

If arrived position is the reference, reference Lamp is ON.

Note) When instructing G27, you should cancel the OFFSET volume

2) G28(Reference automatic return)

By command, commanded axis automatically returns to the reference.
G28 X(u) Z(w) :
Example) When PARAMETER N708(X) is 330000
N709(Z) is 529000

20

www.EngineeringBooksPdf.com
TRAINING
G28 U0 W0 : G27 X100.0 Z100.0

X330.0 X330.0
( ) ( )
Z529.0 X100.0 Z529.0
( )
Z100.0

Action of G28 block presents that the commanded axis goes via the center in rapid feedrate and
returns to the reference.

Note) When instructing G28 block, tool, tool compensation, tool location offset should be can-
celed principlly.

3) G29(Automatic return in reference)

Commanded spindle goes via the remoried center point and decides the position as com-
manded point.
G29 X(u) Z(w) :
∴Generally, it is used right after G28 or G30 command.
G28 X100.0 Z100.0 :
Machine referebce
Center point

G29 X50.0 Z200.0 : X100.0

Return point
Z100.0 X50.0
Start point Z200.0

4) G30(The 2nd reference return)

Commanded spindle automatically returns to the 2nd reference
(coordinate point set in parameter)
G30 X(u) Z(w)) :
∴You should input appropriate distance between works and tool exchangeposition in the relative
parameter.
PARAMETER NO N735(X) = 200000 FS16/18T
N736(Z) = 300000 N1241(X,Z)

The 2nd reference

X
X200.0 G30 U0 W0 :
Z300.0

Reference) Generally, the 2nd reference is used for the start point of program.

21

www.EngineeringBooksPdf.com
TRAINING
G32(THREAD CYCLE)
According to G32 command, straight thread and taper thread of certain lead are cut.
G32 Z(w) F : (G32 is applied to only single block)
X(u) F :
Example 1) STRAIGHT lead

Lead of screw : 3mm

X
δ1 : 5mm

20
δ2 : 1.5mm
δ2 δ1 Depth of cut : 1mm(2cut two times)

Ø50
Z

70

(ABSOLUTE)
G50 T0100 :
G97 S800 M03 :
G00 X90.0 Z5.0 T0101 M8 :
X48.0 :
G32 Z-71.5 F3.0 :
G00 X90.0 :
Z5.0 :
X46.0 :
G32 Z-71.5 :
G00 X90.0 :
Z5.0
X150.0 Z150.0 T0100 :
M30 :

∗ When processing G32 thread, feed(pitch) is modal.

22

www.EngineeringBooksPdf.com
TRAINING
Example 1) STRAIGHT lead
G32 X(u) Z(w) F : Because it is taper, it is applied to both axis at the same time.

Lead of screw : 3mm

X
δ1 : 5mm
δ1 δ2 : 1.5mm
δ2

Ø50
Depth of cut : 1mm(2cut two times)

Ø25
Z

70

(ABSOLUTE) (INCREMENTAL)
G50 S800 T0100 : G50 S800 T0100 :
G97 S800 M03 : G97 S800 M03 :
G00 X90.0 Z5.0 T0101 : G00 X90.0 Z5.0 T0101 :
X22.026 : U-67.974 :
G32 X49.562 Z-71.5 F3.0 : G32 U27.321 W-76.5 F3.0 :
G00 X90.0 : G00 U40.438 :
Z5.0 : W76.5 :
X21.052 : U-68.948 :
G32 X48.588 Z-71.5 : G32 U27.321 W-76.5 :
G00 X90.0 : G00 X90.0 :
Z5.0 : W76.5 :
X150.0 Z150.0 T0100 : X150.0 Z150.0 T0100 :
M30 : M30 :

Reference)
Values of incomplete thread δ1 and δ2.
δ1= 3.6 x L x n L = Lead of thread
1800 n = Rotating time of main spindle

δ2= L x n
1800

23

www.EngineeringBooksPdf.com
TRAINING

G42

-X

R
-Z
+Z

+X

+X

-Z +Z

-X

24

www.EngineeringBooksPdf.com
TRAINING

G41 G42
2 6 1

9
7 5

R
3 8 4

G41

G42

25

www.EngineeringBooksPdf.com
TRAINING

G40
N100 G42 G00 X.. Z..
N105 G01 Z-.. F..
G42 N110
N115
G02 X.. Z-.. R..
G40 G00 X.. Z..
+X

G40
N115

N100
G42
N110 N105

-Z +Z

-X

G41 N100 G41 G00 X.. Z..

N105 G01 Z-.. F..

G40 N110
N115
G02 X.. Z-.. R..
G40 G00 X.. Z..
+X

-Z +Z

-X

26

www.EngineeringBooksPdf.com
TRAINING
Tool diameter compensation

G40 : R compensation cancel

G41 : When located on the left side of material based on the progressing direction,
G42 : When located on the right side of material based on the progressing direction,
X X

G41 G42

Z Z

What is Tool diameter compensation?

If R is on the end of the tool edge, parts which are not impensated only by tool position OFFSET
are occured during the taper cutting or circlar cutting. Therefor, impensating this error automatically
is namelyR compensation.(During the tool diameter compensation, add theR and T-direction in the
R compensation column of OFFSET PAGE.

Example 1) When not using tool diameter compensation(R compensation a and b should be cal-
culated)
compensation ¡ 0.5
PROGRAM
2
C

G01 X25.0 Z0 F0.2 :

b X30.0 Z-2.5 :
45°
8
0.

G00 U1.0 Z1.0 :

R

compensation
Ø30

G28 UO WO :
a ( ¡ 0.5)
M30 :
∗

27

www.EngineeringBooksPdf.com
TRAINING
Example 2) When using tool diameter compensation

∗ You do not have to calculate R compensation a and b

∗ If a position and b position are given on the program, the tool performs automati-

cally R compensation and moves to the next progressing direction.

compensation ¡ 0.5
PROGRAM

2
G42 X26.0 Z0 F0.2 :

C
compensation
b G01 X30.0 Z-2.0 :
X = 30.0
Z = –2.0 ( ¡ 0.5)
Z-30.0 :
Ø30

G00 U1.0 Z1.0 :

X = 26.0 a
Z=0 G28 UO WO :

M30 :
∗

Presentation 1) In case of no compensation

Presentation 2) In case of compensation

28

www.EngineeringBooksPdf.com
TRAINING
1) Direction of imaginary (In case of right hand coordinate)

Direction of imaginary seen from the center of radius is decided by the cutting direction of tool

during the cutting. Therefor, it should be set as much as compensation volume.

Direction and number of imaginary are decided among the following eight

types.
X X X

4 3 8
Z Z Z
5 7 9

1 2 6

<Selecting example of imaginary number>

1 2

3 4

5
6

29

www.EngineeringBooksPdf.com
TRAINING

8
7

2) Compensation setting of X

OFFSET No. Z

OFFSETNO. X Z TOOL DIRECTION

01 0.75 -0.93 0.4 3

0.2 -1.234 10.987 0.8 2
. . . . .
. . . . .
16 . . . .

Command scope of OFFSET volume0– + 999.999mm

30

www.EngineeringBooksPdf.com
TRAINING

G70
FINISHING CYCLE
G70 P Q : +X

N70

N55
N60 N60
-Z +Z

-X

N..

N50 G70 P55 Q70

P N55 G0 G42 X..

N60 G1 Z-..
N65 G2 X.. Z.. R..

Q N70 G1 G40 X..

N..

31

www.EngineeringBooksPdf.com
TRAINING

G71
+X
W+

N75

N60
R U
U+
N70 N65
-Z +Z

-X

N..

N50 G71 U.. R..

N55 G71 P60 Q75 U+.. W+..

P N60 G0 G42 X..

N65 G1 Z-..
N70 G2 X.. Z-.. R..

Q N75 G1 G40 X..

N..

32

www.EngineeringBooksPdf.com
TRAINING
G71(STOCK REMOVAL IN TURNING)
G71 U( ¡ d) R(e) :
G71 P Q U( ¡ u) W( ¡ w) F :
P : Start sequence no.
C
B (R) Q : Final sequence no.
A

∆d
(R)
(F) e U( ¡ d) : Cut volume of one time(Designate
45°
(F) the radius.
R(e) : Escape volume(Always 45) escape
Program command
U( ¡ u) : Finishing tolerance in X axis

∆u/2
(F) : Cutting feed
W( ¡ w) : Finishing tolerance in Z axis
(R) : Rapid traverse A`
∆w F(f) : Cutting feedrate

Example of program

Ø30

Ø40
Ø50
Ø60
20 Ø80
40
60

70
90
110
140

33

www.EngineeringBooksPdf.com
TRAINING
(G70, G71)
N10 G50 S1500 T0101 :
G96 S180 M03 :
G00 X85.0 Z5.0 M08 :
Z0 :
G01 X-1.6 F0.25 :
G00 X83.0 Z2.0 :
G71 U3.0 R1.0 :
G71 P20 Q30 U0.5 W0.1 F0.27 :
N20 G42 G00 X30.0 : G71 CYCLE CUTTING FEED
G01 Z-20.0 F0.17 :
G70 CYCLE CUTTING FEED
X40.0 Z-40.0 :
Z-60.0 :
X50.0 Z-70.0 :
Z-90.0 :
X60.0 Z-110.0 :
Z-140.0 :
X80.0 :
N30 G40 :
G70 P20 Q30 : (When using the same bite)
G00 X200.0 Z200.0 T0100 :
M30 :

¡¯ When finishing, if a different bite is used

G00 X200.0 Z200.0 T0100 :
M01 :
N40 G50 S2000 T0303 :
G96 S200 M03 :
G00 X83.0 Z2.0 M08 :
G70 P20 Q30 :
G00 X200.0 Z200.0 T0300 :
M30 :

34

www.EngineeringBooksPdf.com
TRAINING
Examples of program
Stock Removal in Turning(G71) (Type I)

X Start point
End point

100
80
2
Ø140

Ø100

Ø40
Ø60
Z

40 20 2010 20 30 30 10 2
100

(Diameter designation, metric input)

N010 G00 X200.0 Z100.0 :
N011 G00 X160.0 Z10.0 :
N012 G71 U7.0 R1.0 :
N013 G71 P014 Q021 U4.0 W2.0 F0.3 S550 :
N014 G00 G42 X40.0 S700 :
N015 G01 W-40.0 F0.15 :
N016 X60.0 W-30.0 :
N017 W-20.0 :
N018 X100.0 W-10.0 :
N019 W-20.0 :
N020 X140.0 W-20.0 :
N021 G40 U2.0 :
N022 G70 P014 Q021 :
N023 G00 X200.0 Z100.0 :
M30 :

35

www.EngineeringBooksPdf.com
TRAINING
G72(STOCK REMOVAL IN FACING)
G72 W( ¡ d) R(e) :
G72 P_ Q_ U( ¡ u) W( ¡ w) F :
∆d U( ¡ d) : Cut volume of one time
A`
C
R(e) : Escape volume
A
P : Start sequence No.
Tool path
(F)
Q : Final sequence No.
e
(R)
(R) U( ¡ u) : Finishing in clearance X axis(Diameter
command)

∆u/2
Program command
45°
(F) W( ¡ w) : Finishing in clearance Z axis
B
F(f) : Cutting feedrate
∆w

Example of program
1
C

X40.0 Z-15.0 :
X30.0 :
Z-1.0 :
1
C

X26.0 Z1.0 :
Ø30
Ø40
Ø45
Ø60
Ø80

N14 G40 :
30 15 G70 P12 Q14 :
50 G00 X200.0 Z200.0 T0100 :

N10 G50 S2000 T0100 : M30 :

G96 S180 M03 : ¡¯(When finishing with a different tool)

G00 X85.0 Z5.0 T0101 : G00 X200.0 Z200.0 T0100 :
Z0 : M01 :
G01 X-1.6 F0.2 : N16 G50 S2500 T0300 :
G00 X85.0 Z1.0 : G96 S200 M03 :
G72 W2.0 R1.0 : G00 X85.0 Z5.0 T0303 :
G72 P12 Q14 U0.5 W0.2 F0.25 : G70 P12 Q14 :
N12 G00 G41 Z-51.0 : G00 X200.0 Z200.0 T0300 :
G01 X80.0 F0.2 : M30 :
X78.0 W1.0 :
X60.0 :
Z-45.0 :

36

www.EngineeringBooksPdf.com
TRAINING
Examples of program
Stock Removal in Pacing(G72)

7
X Start point

110
88
Ø160

Ø120

Ø40
Ø80
Z

60 101010 20 20 2
60
(Diameter designation, metric input)
N010 G00 X220.0 Z60.0 :
N011 G00 X176.0 Z2.0 :
N012 G72 W7.0 R1.0 :
N013 G72 P014 Q021 U4.0 W2.0 F0.3 S550 :
N014 G00 G41 Z-70.0 S700 :
N015 X160.0 :
N016 G01 X120.0 Z-60.0 F0.15 :
N017 W10.0 :
N018 X80.0 W10.0 :
N019 W20.0 :
N020 X36.0 W22.0 :
N021 G40 :
N022 G70 P014 Q021 :
N023 G00 X220.0 Z60.0 :
N024 M30 :

37

www.EngineeringBooksPdf.com
TRAINING
G73(PATTEN REPEATING)
G73 U( ¡ i) R(d) W( ¡ k) :
G73 P Q U( ¡ u) W( ¡ w) F :

U( ¡ i) : Excape distance and direction in X axis

(Designated the radius)

∆k+∆w
W( ¡ k) : Escape distance and direction in Z axis
∆w
D R(d) : Repeating time
C ∆i+∆u/2
A
(It is conneeted with the cut volume of each time)
(R) ∆u/2
B P : Start sequence No.
Q : Final sequence No.
∆u/2
A`
∆w U( ¡ u) : Finishing in clearance X axis(Radius des-
ignated)
W( ¡ w) : Finishing in clearance Z axis
F(f) : Cutting feedrate
Example of program
∆u

10
R

Ø20
Ø40
Ø60

20 10 20
50
N10 G50 S2000 T0300 : N12 G00 G42 X20.0 Z2.0 :
G96 S200 M03 :
G01 Z-10.0 F0.15 :
G00 X35.0 Z5.0 T0303 :
G02 X40.0 Z-20.0 R10.0 :
Z0 :
G01 Z-30.0 :
G01 X-1.6 F0.2 :
X60.0 Z-50.0 :
G00 X70.0 Z10.0 :
N16 G40 U1.0 :
G73 U3.0 W2.0 R2 :
G70 P12 Q16 :
G73 P12 Q16 U0.5 W0.1 F0.25 :
G00 X200.0 Z200.0 T0300 :
M30 :

38

www.EngineeringBooksPdf.com
TRAINING
Examples of program
Pattern Repeating(G73)

16
Start point

16
X

130
110
14
2
Ø180

Ø160

Ø120

Ø80
Z

2 14
R
20

60 10 40 10 20 40
220

(Diameter designation, metric input)

N010 G00 X260.0 Z80.0 :
N011 G00 X220.0 Z40.0 :
N012 G73 U14.0 W14.0 R3 :
N013 G73 P014 Q020 U4.0 W2.0 F0.3 S0180 :
N014 G00 G42 X80.0 Z2.0 :
N015 G01 W-20.0 F0.15 S0600 :
N016 X120.0 W-10.0 :
N017 W-20.0 S0400 :
N018 G02 X160.0 W-20.0 R20.0 :
N019 G01 X180.0 W-10.0 S0280 :
N020 G40 :
N021 G70 P014 Q020 :
N022 G00 X260.0 Z80.0 :
N023 M30 :

39

www.EngineeringBooksPdf.com
TRAINING

G74

+X

-Z +Z

-Z

-X

N40 G74 R..

N50 G74 Z-.. Q.. F..

40

www.EngineeringBooksPdf.com
TRAINING
G74(Peck drilling in Z axis divection)
1) Drill cutting cycle
G74 R(e) :
G74 Z(w) Q( ¡ k) F :

∆k` ∆k ∆k ∆k ∆k
R(e) : Retreat volume

C A Z(w) : Final cutting depth

∆i
(R) (R) (R) (R)
Q( ¡ k) : One time cutting depth
∆d

(F) (1000=1mm)
(F) (F) (F) (F)

∆i

U/2
F : Cutting feedrate

∆i`
B
X
e
[0 < ∆i` < ∆i ]
W
Z (R) : Radius traverse
(F) : Cutting feed

Examples of program
∆k` ∆k

(R)
∆d

(F) (F)

N10 G50 S500 T0200 :

G74 R1.0 :
G97 S280 M03 :
G74 Z-90.0 Q5000 F0.23 :
G00 X0 Z5.0 T0202 M08 :
G00 X200.0 Z150.0 T0200 :
Start point of drilling
M01 :

41

www.EngineeringBooksPdf.com
TRAINING
2) Stock removal cycle in side

G74 R(e) :

G74 X(u) Z(w) P( ¡ i) Q( ¡ k) R( ¡ d) F :

∆k` ∆k ∆k ∆k ∆k

C A

∆i
(R) (R) (R) (R)
∆d

(F)
(F) (F) (F) (F)

∆i

U/2
∆i`
B
X
e
[0 < ∆i` < ∆i ]
W
Z (R) : Radius traverse
(F) : Cutting feed

R(e) : Retreat volume(Modal command)

P( ¡ i) : Moving volume of X axis

Q( ¡ k) : Cut volume in Z axis(Q5000=5mm)

X(u) : Composition of X axis

Z(w) : Final cutting depth

R( ¡ d) : Escape wlume at the end point of Z axis proess(Designate the symbol and

radius according to the direction of escape)

F : Cutting feedrate

42

www.EngineeringBooksPdf.com
TRAINING

Ø20
Ø50

Ø10
Ø30
Ø50
10
10

¡¯ If there is one groove, X(u), P( ¡ i) can be omitted.

(In case of omitting, it shall be done at the same time)
N10 N10 G50 S2000 T0100 :
G00 X20.0 Z1.0 : G96 S80 M03 :
G74 R1.0 : G00 X50.0 Z1.0 T0101 :

G74 Z-10.0 Q3000 F0.1 : G74 R1.0 :

G00 X200.0 Z200.0 : G74 X10.0 Z-10.0 P10000 Q3000 F0.1 :

G00 X200.0 Z200.0 T0100 :
M30 :
M30 :
Attention

FANUC 0TC
Q3000=3mm N1 G50 S2000 T0100 :

P10000=10MM G96 S80 M3 :

G0 X47.0 Z1.0 T0101M8 :
G74 R1.0 :
G74 Z-10.0 Q3000 F0.1 :
3

G0 U-5.0 :
Ø50 G74 X20.0 Z-10.0 P2500 Q3000 F0.1 :
G0 X200.0 Z200.0 T0100 :
M30 :
Ø20
Ø50

10

43

www.EngineeringBooksPdf.com
TRAINING

G75
Q<T!

Z = I - T!

+X
t

P
R

-Z Q +Z
X
Z

P...( ¥ M )
-X

N50 G75 R
N55 G75 X... Z-... P... Q...

44

www.EngineeringBooksPdf.com
TRAINING
G75(X directiion grooving : Peck drill cycle in turining)
G75 R(e) :
G75 X(u) Z(w) P( ¡ i) Q( ¡ k) R( ¡ d) F :

(R) A

∆i
(F)

C
(R)

(F)

(R)

U/2
(F)

(R)

(F)

(R)
(F)

∆Κ ∆d
X

W
Z (R) : Radius traverse
(F) : Cutting feed
R(e) : Retreat volume(Modal command)
X(u) : Compostion of X axis
Z(w) : Composition of Z axis
Q(k) : Moving volume in Z axis(Designate with out symblo)
P(i) : Cut volume or X axis(Designate the radius)
R(d) : Escape volume at the end point of X axis process
(Designate the symble according to escape dinetion)
F : Cutting feedrate

45

www.EngineeringBooksPdf.com
TRAINING

10 60
40
20

10

Ø60
Ø80
N10 G50 S500 T0100 :
G97 S_ M03 :
G00 X90.0 Z1.0 T0101 :
X82.0 Z-60.0 :
G75 R1.0 :
G75 X60.0 Z-20.0 P3000 Q20000 F0.1 : ¡¸¡£
G00 X90.0
X200.0 Z200.0 T0100 :
M30 :
¡¯ While it has the same function with G74, X and Z are exchanged.
If there is one groove, volues of Z and P can be omitted at the same time.

46

www.EngineeringBooksPdf.com
TRAINING

G76
N50 G76 Pxx xx xx Q... R...
N55 G76 X... Z... R0 P... Q... F...

1
1
Pxx (0 - 99)
..
n

N50 G76 Pxx xx xx Q... R...

N55 G76 X... Z... R0 P... Q... F...

Pxx
a = F*( )
45
Ο 10

Pxx (0 - 99)

N50 G76 Pxx xx xx Q... R...

N55 G76 X... Z... R0 P... Q... F...

Pxx = 0 Pxx = α ( 80 , 60 , 55 , 30 , 29 )

47

www.EngineeringBooksPdf.com
TRAINING

G76
N50 G76 Pxx xx xx Q... R...
N55 G76 X... Z... R0 P... Q... F...

Q(Xmin)

Q ... ( µm )

+X
Z

-Z +Z
X

N50 G76 Pxx xx xx Q... R...

N55 G76 X... Z... R0 P... -X
Q... F...

48

www.EngineeringBooksPdf.com
TRAINING
G73(Compound type thread cutting cycle)
By G76 command, thread cutting cycle is possible.
FORMAT G76 P(m) (r) (a) Q(∆dmin) R(d)
G76 X(u) Z(w) R(i) P(k) Q(∆d) F(f)

P(m) : Repeating time before the final thread ex) P 0 2 1 0 6 0

(r) : Chamfering at the end part of thread Angle of thread face
(a) : Angle between threads Chanfering volume 1.0 lead omissible
Repeating time

Q( §Edmin) : Min. cut volume(Example : Calculate as Q100=NC and process at least more
than 0.1 for processing of one time)-0.1(Decimal point is vot allowed)

R( §E d) : Finishing clearance(Final finishing clearance)

X(u) : Core diameter of thread
(Command the value of Outer diameter of thread-<height of threadx2>)
Z(w) : Z spindle coordinate at the end point of thread process
R(i) : For omitting, straight thread and R– : X+ and Taper thread
R+ : X– and Taper thread
P(k) : Height of thread(Omit the decimal point <Example>P900=0.9mm)
Q(d) : Initial cut volume (Omit the decimal point <Example>Q500=Designate) the radius
value
F(f) : Cutting feedrate(Lead)
*P(k) : 0.6 x Pitch = Core diameter of thread
Hikgh value
Midium value = 0.6
Low value
(Exampal1) G76 Compound type thread cycle
E (R) A

Tool tip

U/2 B
B
(F)
(R) a
∆d
∆d n

D 1st
∆d

2nd
K

r
k

i 3rd
nth
C
Z
d

w
X

49

www.EngineeringBooksPdf.com
TRAINING

(Exampal1) G76 Compound type thread cycle

1.8
Ø60.64
Ø68 Z

25 105

G00 X80.0 Z130.0 :

1.8





,

G76 P011060 Q100 R200 :

3.68
G76 X60.64 Z25.0 P3680 Q1800 F6.0 ;


,

PROGRAM

N10 G97 S1000 M03

M30x2.0 T0100
G00 X50.0 Z5.0 T0101
P=1.5
G76 P021060 Q100 R100
G76 X28.2 Z-32.0 P900 Q500 F1.5
G00 X200.0 Z200.0 T0100
M30
*

30

50

www.EngineeringBooksPdf.com
TRAINING
(Exampal1) G76 Compound type thread cycle

M40x1.5

M20x1.5

P=1.5

P=1.5 20
25
50

PROGRAM
N10 G97 S800 M03
T0300
G00 X30.0 Z5.0 T0303
G76 P021060 Q100 R100
G76 X18.2 Z-20.0 P900 Q500 F1.5
G00 X50.0 Z-20.0
G76 P021060 Q100 R100
Omissible
G76 X38.2 Z-52.0 P900 Q500 F1.5
G00 X200.0 Z200.0 T0300
M30
*

51

www.EngineeringBooksPdf.com
TRAINING

G90
G00
G01
+X

4 4
-Z +Z

Ø25
50

-X

N1234 G90
N1235 G90 X41 Z-50
N1236 U-8
N1237 U-8

52

www.EngineeringBooksPdf.com
TRAINING
G90 Fixed cycle
1) Single fixed cycle for cutting

FORMAT G90 X(U) Z(W) _R _F_ Taper cutting

X(U) : X coordinate at the tnd point of Z
Z(W) : End point
R- : When cutting from the start point to X+ direction
R+ : When cutting from the start point to X- direction
I/R : Inclination(Designate the radius value)

G90X(U) Z(W) F ; G90X(U) Z(W) R F ;

X X
Z W
4(R)

U/2

U/2
3(F) 1(R)
2(F)

X/2
Z Z W

X/2
Z

R... Rapid traverse

F... Cutting traverse specified by F code

1. U<0, W<0, R<0 2. U>0, W<0, R>0

X X

W
Z Z
2(F)
4(R)

R
U/2

3(F) 1(R)
1(R)
U/2

3(F)
4(R)
R

2(F)
W

3. U<0, W<0, R>0 4. U>0, W<0, R<0

at R U at R U
2 2
X X
W
Z Z

4(R)
R

1(R)
2(F)
U/2

U/2

3(F) 3(F)
2(F) 1(R)
R

4(R)
W

53

www.EngineeringBooksPdf.com
TRAINING
Exampal1) When the taper is R Example)

X X
R
2 2
Ø60

Ø50
Ø30

Ø30
Ø40

Z Z

40 30

PROGRAM PROGRAM

G30 U0 W0 : G30 U0 W0 :

G50 S2000 T0100 : G50 S2000 T0100 :

G96 S200 M03 : G96 S200 M03 :
G00 X61.0 Z2.0 T0101 M8 : G00 X56.0 Z2.0 T0101 M08 :
G90 X55.0 W–42.0 F0.25 :
X50.0 : G90 X51.0 W-32.0 F0.25 :
X45.0 : X46.0 :
X40.0 : X41.0 :
Z-12.0 R-1.75 : X36.0 :
Z-26.0 R-3.5 : X31.0 :
Z-40 R-5.25 : X30.0 :
G30 U0 W0 : G30 U0 W0 :
M30 : M30 :
ƒT When cutting of inside diame-
ter,above format can be used.

54

www.EngineeringBooksPdf.com
TRAINING
(Exampal1) G90 Fixed cycle

Ø20

Ø60
20

PROGRAM

N10 G50 S2000

G96 S180 M03

T0100
G00 X65.0 Z3.0 T0101
G90 X55.0 Z-20.0 F0.25
X50.0
X45.0
X40.0
X35.0
X30.0
X25.0
X20.5
X20.0
G00 X200.0 Z200.0 T0100
M30
ƒT

55

www.EngineeringBooksPdf.com
TRAINING
(Exampal2) G90 Fixed cycle

Ø20
Ø50
Ø55
20

40

PROGRAM

ex1) ex2)

N10 G50 S2000 N10 G50 S2000

G96 S180 M03 G96 S180 M3

T0100 T0100

G00 X60.0 Z0 T0101 G0 X60.0 Z5.0 T0101 M8

G01 X-1.6 F0.2 G90 X50.0 Z-40.0 F0.25

G00 X50.0 Z1.0 X45.0 Z-20.0

G01 Z-40.0 F0.25 X40.0

G00 U1.0 Z1.0 X35.0

G90 X45.0 Z-20.0 F0.25 X30.0

X40.0 X25.0

X35.0 X20.0

X30.0 G00 X200.0 Z200.0 T0100

X25.0 M30

X20.5
X20.0
G00 X200.0 Z200.0 T0100
M30
ƒT

56

www.EngineeringBooksPdf.com
TRAINING

G92
G00
+X
G01

P3 P0

P1
P2

-Z +Z

40
5

50

-X

N1234 G92 X40. Z-55. F5.

57

www.EngineeringBooksPdf.com
TRAINING
G92 Fixed cycle
1) Single fixed cycle for cutting

FORMAT G92 X(U) Z(W) _R_F_

X(U) : X axis coordinate of thread process position of each time

Z(W) : End point
R- : When cutting form the start point to X+ direction.
R+ : When cutting from the start point to X- direction.
I/R : Lead(pitch)

Note) Spindle override and feedrate override of cycle distance are disregarded.

G92x(U) Z(W) F ; Lead(L) is specified G92x(U) _ Z(W)_ F_ ;

X
X
Z W
Z W

U/2 4(R)
3(R)
4(R) 1(R)
3(R) 1(R) 2(F)
2(F)
R
X/2
X/2

Z Z

L L

45 R... Rapid traverse 45

F... Thread cutting specified
r by F code r

58

www.EngineeringBooksPdf.com
TRAINING
Exampal1) When the taper is R Example) M50 x 1.5

F1.5 60
60

2 5 X

6.166
(Ø50.666)

5
Z

Ø40

Ø50
Ø50

30 Z

30

PROGRAM PROGRAM

G30 U0 W0 : G30 U0 W0 :
G50 S1000 T0100 : G50 S1000 T0100 :
G97 S1000 M03 : G97 S1000 M03 :
G00 X70.0 Z5.0 T0101 M08 : G00 X60.0 Z5.0 T0101 M08 :
G92 X49.4 Z–32.0 R–6.166 F1.5 : G92 X49.5 Z–30.0 F1.5 :
X49.0 : X49.2 :
X48.7 : X48.9 :
X48.5 : X48.7 :
- -
- -
G30 U0 W0 : G30 U0 W0 :
M30 : M30 :

ƒT ƒT

59

www.EngineeringBooksPdf.com
TRAINING
(Exampal1) G90 Fixed cycle

M30x1.5
P=1.5

30

PROGRAM

N10 G97 S1000 M03

T0300
G00 X35.0 Z5.0 T0303
G92 X29.5 Z-32.0 F1.5
X29.2
X28.9
X28.7
:
G00 X200.0 Z200.0 T0300
M30
ƒT

60

www.EngineeringBooksPdf.com
TRAINING
(Exampal2) G92 thread cycle

M40x2.0

M20x2.0

15
20 30

PROGRAM

N10 G97 S1500 M03

T0300
G00 X30.0 Z5.0 T0303
G92 X19.5 Z-15.0 F2.0
X19.2
X18.9
X18.6
X18.4
:
G00 X50.0
Z-25.0 S1000
G92 X39.5 Z-50.0 F2.0
X39.2
X38.9
X38.6
X38.4
G00 X200.0 Z200.0 T0300
M30
∗

61

www.EngineeringBooksPdf.com
TRAINING

G94

G00
G01 +X

-Z +Z

Ø25
50

-X

N1234 G94 X25. Z-50.

62

www.EngineeringBooksPdf.com
TRAINING
G94 (Stock vemoval cycle in facing)

FORMAT G92 X(U) Z(W)_R_F_

X(U) : End point

Z(W) : (End point of inclination)= a point of cycle distance
R- : program the veal inclined value.
F : Cutting feedrate

G94X(U) Z(W) F ; G90X(U) Z(W) R F ;

X
X
1(R)
2(F)
1(R)

U/2
4(R)
2(F) 4(R)

U/2
3(F)
X/2 3(F)

X/2
Z W R W
Z Z
a
Z

R... Rapid traverse

F... Cutting traverse specified by F code

1. U<0, W<0, R<0 2. U>0, W<0, R<0

X X
R W
Z Z

4(R) 3(F)
U/2

U/2

2(F) 1(R) 2(F) 4(R)

3(F) 1(R)

R W

3. U<0, W<0, R>0 4. U>0, W<0, R<0

at R W at R W

X X
R W
Z Z

1(R) 3(F)
U/2

2(F) 4(R)
2(F)
U/2

4(R)
1(R)
3(F)
R
W

63

www.EngineeringBooksPdf.com
TRAINING
Exampal)

Ø83.5

Ø40
Z

20 2

PROGRAM

G30 U0 W0 :
G50 S2000 T0100 :
G96 S200 M03 :
G00 X85.0 Z2.0 T0101 M08 :
G94 X40.0 Z–2.0 F0.2
Z–4.0 :
Z–6.0 :
Z–8.0 :
Z–10.0 :
Z–12.0 :
Z–14.0 :
Z–16.0 :
Z–18.0 :
Z-19.7 :
Z–20.0 :
G30 U0 W0 :
M30 :
*

64

www.EngineeringBooksPdf.com
TRAINING
(Exampal 1) G94 Stock removal cycle in facing

Ø15

Ø50
8

PROGRAM

N10 G50 S2500

G96 S180 M03
T0100
G00 X55.0 Z2.0 T0101
G94 X15.0 Z-2.0 F0.2
Z-4.0
Z-6.0
Z-8.0
G00 X200.0 Z200.0 T0100
M30
*

65

www.EngineeringBooksPdf.com
TRAINING
(Exampal 2) G94 Stock removal cycle in facing

Ø12
Ø40
Ø80
10 7

PROGRAM

ex1) ex2)
N10 G50 S2500 : N10 G50 S2500 :
G96 S180 M03 : G96 S180 M3 :
T0300 : T0300 :
G00 X85.0 Z2.0 T0303 : G0 X85.0 Z2.0 T0303 :
G94 X12.0 Z-2.0 F0.2 : G94 X12.0 Z-2.0 F0.2 :
Z-4.0 : Z-4.0 :
Z-6.0 : Z-6.0 :
Z-7.0 : Z-7.0 :
G00 X85.0 Z-5.0 : X 40.0 Z-9.0 :
G94 X40.0 Z-9.0 F0.2 : Z-11.0 :
Z-11.0 : Z-13.0 :
Z-13.0 : Z-15.0 :
Z-15.0 : Z-17.0 :
Z-17.0 : G0 X200.0 Z200.0 T0300 :
G00 X200.0 Z200.0 T0300 : M30 :
M30 : ∗
∗

66

www.EngineeringBooksPdf.com
TRAINING
G96, G97(Constant travelling speed control ON, OFF)

G Code Constant travelling Meaning Unit

speed control
To control the travelling speed
G 96 ON m/min
constantly
Designate the rotating time of
G 97 OFF rpm
main spindle

Example) G96 S100 :

Cutting speed is 100m/min
G97 S100 :
Rotating time of main spindle is 100rpm
G98, G99(Feedrate selection)

G GODE Meaing Unit

G 98 Feedrate per minute mm/min

G 97 Feedrate per rotation mm/rev

Example) G98 G01 Z100.0 F50.0 :

Feedrate of tool is 50mm per minute.
G97 G01 Z10.0 F0.3 :
Feedrate of tool is 0.3mm per rotation of main spindle.

However, unless there is the G98 command, N.C unit is always in G99 condition.
Therefor it is not necessary to command G99 seperately.

67

www.EngineeringBooksPdf.com
TRAINING
<Calculation formular of bite noser>

b
∗ Calculation formular of compensation volume
α
a = r(1–tan 2 )
β
α
a β
b = r(1–tan )
2

r = Rvalue of bite

Example)
Bite Nose a b

0.4 0.468 0.234

R3
NOSE 0.8 0.937 0.468
R=0.8
R3 C1
Ø60

Ø30

23.8
20 23
20
80
17.8
O0035 :
N10 G50 S1500 T0100 : 17

Ø34.4
Ø52.4
Ø36

Ø30
N20 G50 S2000 T0303 : Ø54
G96 S180 M03 :
G00 X35.0 Z5.0 M08 :
Z0:
R+r
G01 X-1.6 F0.2 : 3+0.8=R3.8

G00 X25.063 Z1.0 : R-r

3-0.8=R2.2
G01 X30.0 Z-1.468 F0.17 :
Z-17.8 :
G02 X34.4 Z-20.0 R2.2 :
G01 X52.4 :
G03 X60.0 Z-23.8 R3.8 : Concave R = R–r

G01 Z-80.0 :
Convex R = R+r
R : Circumference R
G00 X150.0 Z150.0 :
r : Bite r
T0300 :
M30 :

68

www.EngineeringBooksPdf.com
TRAINING
Example) PROGRAM

0O
R1 C
A
B

Ø70

Ø60
55

75

CB = (70 – 60) ÷ 2 = 5
OC = R10 – 5 = 5
AO = 10
AC = (AO)2 – (OC)2 28.66
55 – 8.66 = 46.34

G00 X60.0 Z3.0 :

G42 Z1.0 :
G01 Z-46.34 F0.23 :
G02 X70.0 Z-55.0 R10.0 :
I10.0
G01 Z-75.0

69

www.EngineeringBooksPdf.com
TRAINING
Example) PROGRAM
80

30
D R5

a
B
C B E F
E G C A
a
R3 20
D
Ø100

Ø60
Ø30
EF = (100 – 60) ÷ 2 = 20 BF = 20° tan x 15 = 5.45955
OC = 20 x 30 tan = 11.547 α = (180 – 70) ÷ 2 = 55°
α = (180 – 60) ÷ 2 = 60° BC = 3 x 35° tan = 2.1
AC = BC AC = AB
AC = 2.887 x 60° sin = 2.5 AE = 2.1 x 70° sin = 1.973
2.887 x 30° cos = 2.5 ∗ X ¡ 1.973 x 2 = 3.947
∗ X ¡ 2.5 x 2 = 5
CG = 2.887 x 30° sin = 1.444 ♠ Coordinate value
2.887 x 60° cos = 1.444 A ¡ X = 60 – 3.947 = 56.053
Z = 5.459 – 0.718 = 4.741
♠ Coordinate value C ¡ X = 60
A ¡ X = 60 Z = 5.459 + 2.1 = 7.559
Z = 80 – (CE – AC) = 65.566 D ¡ X = R3 – AE ¡ 3 – 1.973 = 2.054
B ¡ X = 60 + BG = 65 Z = BE + BC ¡ 2.1 + 0.718 = 2.816
Z = 68.453 + 1.444 = 69.897
A ¡ X = R5 = 5
Z=0

70

www.EngineeringBooksPdf.com
TRAINING

O'
E R3
0

R3
O"
E
J D
C A
ø78 ø50
H R30
30 ø10
G F O B

A
1) 30
5 (OB)2 = (OA)2- (AB)2 = (30)2 - (5)2 = 875 = 29.58
0
(29.58) B
C OC = 30, CF = 25 OF = (50)2 - (25)2 = 16.583
2)

25
30 COF = SIN COF = 25 = 56.442O
50

COF = O'CD
F (16.583) O
COF = O'CD
C
30 CF = O'D O'D = 25
25
0 DH = O'H - O'D = 30 - 25 = 5 6D = 25
F

O' of X 50 + 25 + 25 = 100

O' of Z OB + OF + CD = 29.58 + 16.383 + 16.583 = 62.746

O" of X 78 - 6 = 72

(100-72)
O' E = = 14 O"O' = 3 + 30 = 33
2
O'E = 14
O'
33
14 O"E = 332 - 142 = 29.883

O" E
E of Z 62.746 + 29.883 = 92.629

I of X 72 + 1.2727 + 1.2727 = 74.5454

I of Z 92.629 - 2.7166 = 89.9124

SIN O'O"E = 14 = 25.1027O

33
I
3 I J = SIN 25.1027 X 3 = 1.2727
O
25.1027
O" J O"J = COS 25.1027 X 3 = 2.7166

71

www.EngineeringBooksPdf.com
TRAINING
(Example 1)

Process Facing process, Outside diameter process

Dimension ø 45 x 60L
Material S45C

4-C1

Ø10
Ø20
Ø30
Ø40
Ø45
15 10 10 10
60

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal

PCLNR/L–1 Finishing PCLNR/L–1 Finishing

72

www.EngineeringBooksPdf.com
TRAINING
(Example 2)

Process Facing process, Outside diameter taperprocess

Dimension ø 70 x 100L
Material S45C

C1 C2

Ø30

Ø50

Ø60

Ø70
20 40 20

100

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal

PCLNR/L–1 Finishing PCLNR/L–1 Finishing

73

www.EngineeringBooksPdf.com
TRAINING
(Example3)

Process Facing process, Outside diameter taper process(Chamfering, R process)

Dimension ø 60 x 75L
Material S45C

C1 R2 C2

Ø20

Ø30

Ø40

Ø50

Ø60
15 30 15

75

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal

PCLNR/L–1 Finishing PCLNR/L–1 Finishing

74

www.EngineeringBooksPdf.com
TRAINING
(Example4)

Process Facing process, Outside diameter(Groove process, Chamfering R process)

Dimension ø 70 x 70L
Material S45C

R5 4-C1
3

2
3

2
Ø20

Ø30

Ø50

Ø60

Ø70
15 15 15 10

70

Condition of using tool

Facing process Outside diameter process Groove process

TOOL PROCESS TYPE TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal PCLNR/L Stock removal + Finishing
PCLNR/L–1 Finishing PCLNR/L–1 Finishing PCLNR/L–1

75

www.EngineeringBooksPdf.com
TRAINING
(Example5)

Process Facing process, Outside diameter(Groove process, Chamfering R process, Thread process)
Dimension ø 90 x 80L
Material S45C

C1.5

R3

C2 C2

Ø30

Ø40

Ø60

Ø80

Ø90
5 10 20 25

80

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing

Groove process Thread process

TOOL PROCESS TYPE TOOL PROCESS TYPE

R/L 154.91 Stock remova + Finishing R/L 166.0 Stock remova + Finishing

76

www.EngineeringBooksPdf.com
TRAINING
(Example6)

Process Facing process, Outside diameter(Groove process, Thread process, Relief)

Dimension ø 65 x 88L
Material S45C

M42 2.0 M42 2.0

+
C1
2-C1.5
R2

Ø36

Ø42

Ø55

Ø65
10 40 15

85

Condition of using tool

Facing process Outside diameter process Groove process

TOOL PROCESS TYPE TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal R/L 154.91 Stock removal + Finishing
PCLNR/L–1 Finishing PCLNR/L–1 Finishing

Facing process Thread process

TOOL PROCESS TYPE TOOL PROCESS TYPE

Relief Stock remova + Finishing R/L 166.0 Stock remova + Finishing

77

www.EngineeringBooksPdf.com
TRAINING
(Example7)

Process Outside diameter R process

Dimension ø 80 x 120L
Material S45C

R3
R6
R13
R16
Ø80

Ø77
5.66

5 31 5 25.3 5 11.2 5 5

120

Condition of using tool

Outside diameter process

TOOL PROCESS TYPE

SVVBN Stock removal + Finishing

78

www.EngineeringBooksPdf.com
TRAINING
(Example8)

Process Outside diameter circumference process

Dimension ø 82 x 120L
Material S45C

R3

0
R3

0
R3
Ø82

Ø78

Ø50

Ø10
5
120

Condition of using tool

Outside diameter circumference process

TOOL PROCESS TYPE

SVVBN Stock removal + Finishing

79

www.EngineeringBooksPdf.com
TRAINING
(Example9)

Process Outside diameter(Groove process, Thread process, Chamfering R process)

Dimension ø 60 x 110L
Material S45C

C1

3
R3

C3
R10 C0.5 C1.5
3

3
3

Ø20

Ø40

Ø60
20 20 20 15 15
105

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing

Groove process Thread process

TOOL PROCESS TYPE TOOL PROCESS TYPE

R/L 154.91 Stock remova + Finishing R/L 166.0 Stock remova + Finishing

80

www.EngineeringBooksPdf.com
TRAINING
(Example10)

Process Outside diameter process, Inside diameter process

Dimension ø60 x 110L
Material S45C

20 25

105

Ø20
Ø30
Ø40
Ø50
Ø70
Ø80
Ø90
10 10 10
60

Condition of using tools

Facing process Outside diameter process Inside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal S-20S PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing S-20S PCNR/L-1 Finishing

81

www.EngineeringBooksPdf.com
TRAINING
(Example11)

Process Outside diameter process, Inside diameter process

Dimension ø110 x 75L x ø25(Pipe)
Material S45C

C1

R1
C1
C1
C1

Ø105
Ø110
Ø25
Ø30
Ø40
Ø50
Ø70
Ø90
10 10 10
70

Problem 1) Program when the material is pipe

Problem 2) Program when the material is a round bar

Condition of using tools

Facing process Outside diameter process Inside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal S-20S PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing S-20S PCNR/L-1 Finishing

82

www.EngineeringBooksPdf.com
TRAINING
(Example12)

Process Outside diameter process, Inside diameter process

Dimension ø 110 x 75L x ø 25(Pipe)
Material S45C

10 20 15 15
C1

C0.5

R5 C1

3
C0.5 C1
3

3
3

R2
C1

Ø100
Ø110
Ø115
Ø20
Ø25
Ø40
Ø50
Ø80
Ø85
15 15 12

75

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing

Groove process Inside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock remova + Finishing S-20S PCLNR/L Stock remova
PCLNR/L–1 S-20S PCLNRL-1 Finishing

83

www.EngineeringBooksPdf.com
TRAINING
(Example13)

Process Outside diameter process, Inside diameter process(Chamfering, R, Groove)

Dimension ø90 x 60L x ø20(Pipe)
Material S45C

35

3 R3
C1

2
C1 C1
R2

Ø20
Ø25
Ø40
Ø50
Ø80
Ø90
5 10 20

55

Problem 1) Program when the material is pipe

Problem 2) Program when the material is a round bar

Condition of using tool

Facing process Outside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing

Inside diameter Groove process Inside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock remova + Finishing S-20S PCLNR/L Stock remova
PCLNR/L–1 S-20S PCLNRL-1 Finishing

84

www.EngineeringBooksPdf.com
TRAINING
(Example14)

Process Outside diameter process(Chamfering, R, Groove, Thread, Relief process)

Dimension ø110 x 90L x ø20(Pipe)
Material S45C

20 15 10 25 M8 2.0

+
3-C1.5
R2
1
1 3

3 3
3
M50 1.5

+
3

3
4-C1

R2 M40 1.5
+

Ø100
Ø105
Ø110
Ø20
Ø25
Ø35
Ø40
Ø50
Ø80
Ø88
10 10 15 15

90

Problem 1) Program when the material is pipe

Problem 2) Program when the material is a round bar

Condition of using tools

Facing process Outside diameter process Inside diameter process

TOOL PROCESS TYPE TOOL PROCESS TYPE TOOL PROCESS TYPE

PCLNR/L Stock removal PCLNR/L Stock removal S-20S PCLNR/L Stock removal
PCLNR/L–1 Finishing PCLNR/L–1 Finishing S-20S PCNR/L-1 Finishing

Inside diameter Groove process Vutsude diameter relief process Outside diameter Groove process

TOOL PROCESS TYPE TOOL PROCESS TYPE TOOL PROCESS TYPE

R/L 154.3 Stock removal + Finishing PCLNR/L Stock removal R/L 154.91 Stock removal + Finishing
PCLNR/L–1 Finishing

85

www.EngineeringBooksPdf.com
TRAINING
Calesslating table of trigonometric function

C = A+B
2 2 B B = A-C
2 2
Sin D = E = 90°−E
A
A A A
E

B
90° 90° D 90° 90°
D
C C

C B
Sin E = D = 90°−E A = B+C tan D =
A C
A A
E E

B
90° 90° 90° 90°
D D
C C C

B=SinDxA C=AxcosD B=AxcosE B=AxSinE

A A A A
E E

B
B

90° 90° 90° 90°

D D
C C

A= C C=BxcotD A= B A=BxtanE
SinD cosE
A A
E E
B

B
90° 90° 90° 90°
D D
C C

A= C B=CxtanD A= C B=CxcotE
cosD SinE
A A
E E

B
B

90° 90° 90° 90°

D D
C C C C

AxSinF E=180°-(D-F) AxSinE tanD = AxSinE

B= B = sinD
cosD B-AcosE
B B
C

D D D D
F F E E E
A A

AxSinE SinF =
BxSinD E=180°-(D+F)
F=180°-(D+E) C = SinD A
B
C

D D D D
F E E F F E
A A
B-SinF
AxBxSinE cosD = C+B+A SinD = F=180°-(D+E)
2 2BC A
B
B B
D
C

D D
E F F E

A A A

86

www.EngineeringBooksPdf.com
TRAINING
FORMULA
1. The puthagorean theorem

C2 = A2 + B2 C = A2 + B2
C
B A2 = C2 – B2 A = C2 – B2
B2 = C2 – A2 B = C2 – A2
A

2. Trigonometric function

C
B SINα° = B , COSα° = A , TANα° = B
C C A
α°
A A = C × COSα° A= B
TANα°
B = C × SINα° B = A × TANα°
C= B C= A
SINα° COSα°
3. SIN law
When finding the length of the two sides(Oneside and two angles are known)
When finding the other angle(Two sides and one angle are know)

γ°
A B A = B = C
SINα° SINβ° SINγ°
β° α°
C
4. COS law
When finding the other side(Two sides and one angle are known)
When finding the other angle(Lengthsof three sides are known)

α° 2 2 2
A2 = B2 + C2 – 2B.C COSα° COSα° = B + C – A
C B 2BC
2 2 2
B2 = C2 + A2 – 2C.A COSβ° COSβ° = C + A – B
2CA
2
β° γ° C2 = A2 + B2 – 2A.B COSγ° COSγ° = A + B2 – C2
2AB
A

87

www.EngineeringBooksPdf.com
TRAINING
♠ DECHNICAL GUIDE

CALCULATING FORMULA

¥. D. L x 60 Cutting length x 60
♠ Drocess time(sec/ea) = = = sec
100V x F Arerage of rotating time

♠ Output(8Hrs/day) = 8Hrs x 60 x 60 = ea

Required time per unit

Object time x Quantity to be processed

♠ Required day for process = 8 x 60 =Day
60

♠ Surface roughress = Feed volume x 1000 = R.t µm

2

8 x NOSER

♠ Cutting volume = cm3/min V = Cutting speed

F = Feed volume(mm/rev)
V. F.D = LT D = Depth of cutting
ft x W xD = ML ft = Feedrate(mm/min)
1000 W= Width of cutting

♠ Cutting condition(Material : AL)

∗ EXTREME – FINISHING V = 870
F = 0.05~0.15
t = 0.025~2.0

∠ FINISHING V = 720
F = 0.1~0.3
t = 0.5~2.0

∠ LIGHT V = 600
ROUGHING F = 0.2~0.5
t = 2.20~4.0

88

www.EngineeringBooksPdf.com
TRAINING
Cutting condition
1. Cutting condition

Depth of cutting Cutting speed Feedrate

Material Classification Material of tool
d(mm) v (m/min) F (mm/rev.)
Carbon steel Stock vemoval 3~5 180 ~ 200 0.3 ~ 0.4 P 10 ~ 20
60kg/mm
2~3 200 ~ 250 0.3 ~ 0.4 P 10 ~ 20
(Tensile
strength) Finishing 0.2 ~ 0.5 250 ~ 280 0.1 ~ 0.2 P 01 ~ 10

Thread 124 ~ 125 P 10 ~ 20

Grooving 90 ~ 110 0.08 ~ 0.2 P 10 ~ 20

Center drill 1000 ~ 1600 rpm 0.08 ~ 0.15 SKH 2

Drill ~ 25 0.08 ~ 0.2 SKH9

Alloy steel Stock removal 3~4 150 ~ 180 0.3 ~ 0.4 P10 ~ 20
140kg/mm 2

Finishing 0.2 ~ 0.5 200 ~ 250 0.1 ~ 0.2 P 10 ~ 20

Grooving 70 ~ 100 0.08 ~ 0.2 P 10 ~ 20

Castiron Stock removal 3~4 200 ~ 250 0.3 ~ 0.5 K 10 ~ 20
HB 150 Finishing 0.2 ~ 0.5 250 ~ 280 0.1 ~ 0.2 K 10 ~ 20

Grooving 100 ~ 125 0.08 ~ 0.2 K 10 ~ 20

Aluminum Stock removal 2~4 400 ~ 1000 0.3 ~ 0.5 K 10

Finishing 0.2 ~ 0.5 700 ~ 1600 0.1 ~ 0.2 K 10

Grooving 350 ~ 1000 0.1 ~ 0.2 K 10

Bronge Stock removal 3~5 150 ~ 300 0.2 ~ 0.4 K 10
Brass
Finishing 0.2 ~ 0.5 200 ~ 500 0.1 ~ 0.2 K 10

Grooving 150 ~ 200 0.1 ~ 0.2 K 10

Staialess steel Stock removal 2~3 150 ~ 180 0.2 ~ 0.35 P 10 ~ 20

Finishing 0.2 ~ 0.5 180 ~ 200 0.1 ~ 0.2 P 01 ~ 10

Grooving 60 ~ 90 ~ 0.15 P 10 ~ 20

(Note) 1) Conditions for tools coated

2) Cutting condition shall be changed by the shape and angle of tools

89

www.EngineeringBooksPdf.com
TRAINING
2. Cutting time of thread process(For thread precessing with the S 45 C)

H/8

0.072P
R H1 H2 H

P
H/4

PITCH P1.0 1.0 1.25 1.5 1.75 2.0 2.5 3.0 3.5 4.0 4.5 5.0

CUTTING DEPT H2 0.6 0.74 0.89 1.05 1.19 1.49 1.79 2.08 2.38 2.68 2.98

CORNER ROUND R 0.07 0.09 0.11 0.13 0.14 0.18 0.22 0.25 0.29 0.32 0.36

1 0.25 0.30 0.30 0.30 0.30 0.30 0.35 0.35 0.35 0.40 0.45

2 0.20 0.20 0.20 0.25 0.25 0.28 0.30 0.35 0.35 0.35 0.35

3 0.10 0.11 0.14 0.16 0.20 0.24 0.26 0.30 0.30 0.30 0.32

4 0.05 0.08 0.12 0.12 0.14 0.20 0.22 0.25 0.26 0.28 0.30

5 0.05 0.08 0.10 0.11 0.15 0.18 0.20 0.23 0.25 0.25

6 0.05 0.07 0.08 0.11 0.13 0.15 0.20 0.22 0.25

SCREW
7 0.05 0.06 0.09 0.10 0.12 0.17 0.20 0.20
CUTTING
8 0.05 0.07 0.08 0.10 0.14 0.15 0.17
NUMBER OF
9 0.05 0.07 0.08 0.10 0.12 0.15
TIMES
10 0.05 0.05 0.10 0.10 0.15

11 0.05 0.05 0.08 0.08 0.10

12 0.05 0.05 0.08 0.10

13 0.05 0.05 0.08

14 0.05 0.06

15 0.05 0.06

90

www.EngineeringBooksPdf.com
TRAINING

+X

-Z M W +Z

WORK SHIFT VALUE

-X

7 8 9
RESET ALTER
OFFSET / GEOMETRY O1000 N0000 O N G
NO. X Z T R
10.000 1.000 0.000 4 5 6
G 01 0 INSRT
X Y Z
G 02 1.486 -49.561 0.000 0 CURSOR
G 03 1.486 -49.561 0.000 0 1 2 3
G 04 0.000 0.000 0.000 DELET
0 H F R
G 05 1.486 -49.561 0.000 0
G 06 1.486 -49.561 0.000 – 0 . / #
0
M S T EOB
G 07 1.486 -49.561 0.000 0
G 08 1.486 -49.561 4t h K Q
ACT. POSITION(RELATIVE) J NO. CAN
B I P
U 0.000 W 0.000
PAGE
NUM. MZ 120. S MDI 0T
MENU
POS PRGRM INPUT
OFSET
WEAR GEOM W.SHIFT MRCRO
DGNOS OPR AUX OUTPT
PARAM ALARM GRAPH START

91

www.EngineeringBooksPdf.com
TRAINING

7 8 9
RESET ALTER
O N G
WORK SHIFT
4 5 6
(SHIFT VALVE) X Y Z
INSRT
CURSOR
X 0.000
1 2 3
Z 23.061 H F R
DELET

ACT. POSITION(RELATIVE) – 0 . / #
M S T EOB
U 0.000
4t h K Q
J NO. CAN
B I P
ADRS.
PAGE
MDI
MENU
POS PRGRM INPUT
OFSET
WEAR GEOM W.SHIFT MRCRO
DGNOS OPR AUX OUTPT
PARAM ALARM GRAPH START

Work shift method using the tool measure

1.Return to the reference manually.

2. Install the work piece to the JAW and move the TURRET to appropriate position, and then pre-
pare the basic tools to work.
3. On the section of material, TOUCH of process in facing the basic tool
∴At this, it is absolutely not allowed to move the Z spindle.
4. Select WORK/SHIFT screen.
PAGE

Method) MENU Push the bottun to select the WORK/SHIFT

OFSET
5. Inpit the DATA.
5
Method) M W Z DATA push bottuns one by one, and push MEASURE on the
console, and push INPUT , then identify the input.
∗ DATA Z coordinate value in the program (Touched position)
∗ After input, Z value on the screen of WORK/SHIFT is automatically calculated and input.
6. As the input is completed,

PAGE

Push to select the OFFSET screen.

92

www.EngineeringBooksPdf.com
TRAINING

Offs.
+X

-Z +Z

60

80

-X

7 8 9
RESET ALTER
OFFSET / GEOMETRY O1000 N0000 O N G
NO. X Z T R
10.000 1.000 0.000 4 5 6
G 01 0 INSRT
X Y Z
G 02 1.486 -49.561 0.000 0 CURSOR
G 03 1.486 -49.561 0.000 0 1 2 3
G 04 0.000 0.000 0.000 DELET
0 H F R
G 05 1.486 -49.561 0.000 0
G 06 1.486 -49.561 0.000 – 0 . / #
0
M S T EOB
G 07 1.486 -49.561 0.000 0
G 08 1.486 -49.561 4t h K Q
ACT. POSITION(RELATIVE) J NO. CAN
B I P
U 0.000 W 0.000
PAGE
NUM. MZ 120. S MDI 0T
MENU
POS PRGRM INPUT
OFSET
WEAR GEOM W.SHIFT MRCRO
DGNOS OPR AUX OUTPT
PARAM ALARM GRAPH START

93

www.EngineeringBooksPdf.com
TRAINING

7 8 9
RESET ALTER
OFFSET / GEOMETRY O1000 N0000 O N G
NO. X Z T R
0.000 0.000 0.000 4 5 6
G 01 0 INSRT
X Y Z
G 02 0.000 0.000 0.000 0 CURSOR
G 03 0.000 0.000 0.000 0 1 2 3
G 04 0.000 0.000 0.000 DELET
0 H F R
G 05 0.000 0.000 0.000 0
G 06 0.000 0.000 0.000 – 0 . / #
0
M S T EOB
G 07 0.000 0.000 0.000 0
4t h K Q
ACT. POSITION(RELATIVE) J NO. CAN
B I P
U 0.000 W 0.000
PAGE
NUM. MZ 120. S MDI 0T
MENU
POS PRGRM INPUT
OFSET
WEAR GEOM W.SHIFT MRCRO
DGNOS OPR AUX OUTPT
PARAM ALARM GRAPH START

OFFSET method using Tool measure

Z axis OFFSET
1. After selecting OFFSET screen
CURSOR

push to move the OFFSET No. of the basic tool .

∗ In gereral, tool no. and OFFSET No. shall be the same

2. After selecting numbers, input the coordinate value of Z in the current position which is touched.
The method shall be the same as work shift. For summary,
5
M W Z DATA MEASURE INPUT

Located in the console

Touched currend position is the Z coordinate value in the program.
4
Select Z axis. In case of X axis, X should be pushed.
Indicates the initial “M” of measure.
After input as above, Z value of OFFSET selected by the cursor is automatically input, but the
basic tool becomes “ 0 ”(zero). If another value is given, start from the begining again.(Work shift
end)
X axis OFFSET
3. Continuously, process the outside diameter with the basic tool, and retreat the Z spindle to +
direction(right hand), stop rotating, then measure the processed outside diameter(Xvalue). If the
measured value is ø52.34, the position of tool is X52.34 therefor, input the X value.
5
M Z DATA MEASURE INPUT

5 2 ¡⁄ 3 4

94

www.EngineeringBooksPdf.com
TRAINING
∗ As you input with above method, X value on OFFSET screen is automatically input.

4. prepare another tool which you want to OFFSET to the work position.

5. Touch slightly on the section of the material.

6. If you input with the same method as finding the OFFSET value of Z spindle written previously, Z

OFFSET value of this tool is autonatically input. (Difference of length compared with the basic

tool)

7. Find the X OFFSET value with the same method as 3.

8. For all other tools, OFFSET with repeating above method(1~3).

(Attention)

1. On WORK/SHIFT screen, input only Z value, not X value.

(∗ Except the GANG TYPE)

2. For the drill and a kind of center drill, input only the OFFSET of Z spindle, leave the X value as

“ 0 ”.

3. Above explanation to find the value of OFFSET is the method when input only the Z value on

WORK/SHIFT screen.

If you input the X axis with the Z axis on WORK/SHIFT screen, you should input the OFFSET

value of X spindle for all tools which are processed in the center of main spindle like the drill

and the center drill.

5. If you OFFSET with above method with using the function of tool measure, you don,t have to

designate the coordinate as G50 during the programming.

Example)

(When using TOOL MEASURE)

O 3333 :

N1 G50 T0100 S1800 M42 :

G96 S100 M03 :

(When not using TOOL MEASURE)

O 3334 :

N1 G50 T100. Z100. T0100 S1800 M42 :

G96 S170 M03 :

95

www.EngineeringBooksPdf.com
TRAINING

M-FUNCTION
M00 : PROGRAM STOP
When M00 is commanded in automatic operation mode(MDI or MEM mode), the automatic oper-
ation will stop after completion of the command in the block containing M00.
When the machine is stopped by M00 code. Manual operation can be done if the mode selector
switch is turned to JOG position.
To restart cycle, select the mode selector switch to previous automatic operation mode and then
depress the CYCLE START button.
NOTE1)
Spindle stops after completion of M00, then chuck open-close can be done by manual without
changing the MODE.
M01 : OPTIONAL STOP
This command is used to stop the machine temporarily by slash(/) and check workpiece at the
end of each tool operations. OPTIONAL STOP switch(toggle switch) is used to selection this
code.
M02 : END OF PROGRAM
This code is used in the last block of chucking work part program to end the program.
When this code occurs during the automatic operation of the machine, the program returns to
the head after performing the other command in the block, the control is reset, this automatic
mode ends and the machine stop.
M03 : MAIN-SPINDLE FORWARD DIRECTION
Specifies to start the main spindle rotation in counterclockwise direction. S code should be spec-
ified in the same block or previous.
If M03 code is specified when the chuck is open, the sequence error will occur.
M04 : MAIN-SPINDLE REVERSE DIRECTION
Specifies to start the main spindle rotation in clockwise direction. S code should be specified in
the same block or previous.
If M04 code is specified when the chuck is open, the sequence error will occur.
M05 : MAIN-SPINDLE STOP
Specifies to stop the main spindle rotation. Even M05 is specified, the command spindle speed
remains effective. Therefore, if M03 or M04 is specified again, the spindle will rotate by the same
speed as the previous speed.
M07 : HIGH PRESSURE COOLANT ON (optional)
Specifies to start the high pressure coolant pump.
M08 : COOLANT ON
Specifies to start the coolant pump. The coolant pump will start when the COOLANT switch on
the operating panel is set to ON position.
M09 : COOLANT OFF
Specifies to stop the high pressure coolant pump and coolant pump.
M10: PART CATCHER1 ADVANCE (optional)
This command moves the part catcher1 advance.

96

www.EngineeringBooksPdf.com
TRAINING

M11 : PART CATCHER1 RETRACT (optional)

This command moves the part catcher1 retract.
M13 : AIR BLOW FOR TURRET (optional)
Air blow for turret when M13 is commanded.
M14 : AIR BLOW FOR MAIN SPINDLE (optional)
Air blow for main spindle when M14 is commanded.
M15 : AIR BLOW OFF (optional)
Air blowing stops.
This command is available on M13, M14.
M17 : MACHINE LOCK ON
Specifies to machine lock on. This command is specified only MDI mode.
M18 : MACHINE LOCK OFF
Specifies to machine lock off. This command is specified only MDI mode.
M19 : MAIN- SPINDLE ORIENTATION (optional)
This code stops main-spindle at fixed angle.
M19 Sxxx : Main-spindle multi orientation (ORIENTATION “B”)
When M19 code and S code should be specified in the same block, the spindle stops position is
determined by S code.
M24 : CHIP CONVEYOR RUN (optional)
Specifies to run the chip conveyor.
M25 : CHIP CONVEYOR STOP (optional)
Specifies to stop the chip conveyor.
M30 : PROGRAM END & REWIND (continuous running)
Return to head of the memory by M30 command, reset and stop.
The program is restarted by cycle start and specifies at last block.
M31: INTERLOCK BY-PASS (MAIN-SPINDLE & TAILSTOCK)
This code is used when cycle start is available the spindle unclamp and the tail stock quill opera-
tion during spindle rotating
M32 : STEADY REST CLAMP/UNCLAMP DURING SPINDLE ROTATION
This code is interlock by-pass of spindle rotating when STEADY REST is used.
STEASY REST clamp(M38 or M58) and unclamp(M39 & M59) is valid during spindle rotating
with M66.
M33 : REVOLVING TOOL-SPINDLE FORWARD DIRECTION
Revolving tool-spindle starts forward rotation.
M34 : REVOLVING TOOL-SPINDLE REVERSE DIRECTION
Revolving tool-spindle starts reverse rotation.
M35 : REVOLVING TOOL STOP
Revolving tool-spindle stops.

97

www.EngineeringBooksPdf.com
TRAINING

M38 : STEADY REST CLAMP(optional-right side), M58 : STEADY REST CLAMP(optional-left side)
Specifies to clamp the steady rest.
M39 : STEADY REST CLAMP(optional-right side), M59 : STEADY REST CLAMP(optional-left side)
Specifies to unclamp the steady rest.
M40 : GEAR CHANGE NEUTRAL
M41 : GEAR CHANGE LOW
M42 : GEAR CHANGE MIDDLE
M43 : GEAR CHANGE HIGH
Specifies to change the each gear range.
M46 : Prog. TAIL STOCK BODY UNCLAMP & TRACTION BAR ADVANCE (optional)
Simultaneous start of prog. Tail stock body unclamp and traction bar retract with this
command.
M47 : Prog. TAILSTOCK BODY CLAMP & TRACTION BAR RETRACT (optional)
Simultaneous start of prog. Tail stock body clamp and traction bar advance with this
command.
M50 : BAR FEEDING (optional)
When automatic bar feeder is attached, feed of material is performed.
M52 : SPLASH GUARD DOOR OPEN (optional)
The splash guard is opened with this command.
M53: SPLASH GUARD DOOR CLOSE (optional)
The splash guard is closed with this command.
M54 : PARTS COUNT (optional)
When M54 is commanded, pieces counter.
M61 : SWITCHING LOW SPEED (only aP60)
When the aP60 spindle motor is use, output torque and speed range of spindle is differ-
ence by power line switching. M61 is used to low speed rpm(Y-CONNECTION). 400 ˜
500 rpm(18.5kw)
M62 : SWITCHING HIGH SPEED (only aP60)
M62 is used to high speed rpm( -CONNECTION). 750 ˜ 4500 rpm(22kw)
M63 : MAIN-SPINDLE CW & COOLANT ON
Simultaneous start of main-spindle forward rotation and coolant.
Spindle forward and coolant are preformed by one(M63) command. Coolant comes out
only when operation panel switch is “on”.
M64 : MAIN-SPINDLE CCW & COOLANT ON
Simultaneous start of main-spindle reverse rotation and coolant.
Spindle reverse and coolant are preformed by one(M64) command. Coolant comes out
only when operation panel switch is “on”.

98

www.EngineeringBooksPdf.com
TRAINING

M65 : MAIN-SPINDLE & COOLANT STOP

Stop of main-spindle rotation, coolant is stopped by one command.
M66 : DUAL CHUCKING LOW CLAMP (optional)
Main-chuck is closed by low pressure.
M67 : DUAL CHUCKING HIGH CLAMP (optional)
Main-chuck is closed by high pressure.
M68 : MAIN-SPINDLE CLAMP
Specified to open the main-chuck automatically such as bar work.
M69 : MAIN-SPINDLE UNCLAMP
Specified to close the main-chuck automatically such as bar work.
M70 : DUAL TAILSTOCK LOW ADVANCE (optional)
Tailstock bar is advanced by low pressure.
M74 : ERROR DETECT ON
When M74 is in effect, the control proceed to the next block regardless of the pulse lag of
servo between block for liner and circular interpolation except positioning (G00).
The permits the machine to move smoothly between blocks.
However, the corner of the workpiece may not be quite sharp.
M74 command is modal, and it will remain effective until M75 is command.
M75 : ERROR DETECT OFF
Specifies to release the state of error detection ON. When the power is turned on, M75
will be in effect, and it will remain effective until M74 is command.
M76 : CHAMFERING ON
When M76 is specified before the command of thread cutting cycle G76 or G92, the
threading tool will pull out at the terminating thread portion.
M77 : CHAMFERING OFF
Cancel the command of pull out threading function which as specified by M77 code.
M77 code is the modal code.
M78 : TAIL STOCK QUILL ADVANCE
The tail stock quill is advanced with this command.
M79 : TAIL STOCK QUILL RETRACT
The tail stock quill is retracted with this command.
M80 : QUICK-SETTER SWING ARM DOWN (optional)
Specifies to up the quick-setter swing arm.
M81 : QUICK-SETTER SWING ARM UP (optional)
Specifies to up the quick-setter swing arm.

99

www.EngineeringBooksPdf.com
TRAINING

M82 : MIRROR IMAGE ON

Specifies to mirror image on.
M83 : MIRROR IMAGE OFF
Specifies to mirror image off.
M84 : TURRET CW ROTATION
This code is used to switch the direction of turret indexing to CW when it is set in the
automatic selection mode.
As this code is as non-modal code, it should be used in the same block the T-code.
M85 : TURRET CCW ROTATION
The turret indexes in clockwise by specifying M85 in the same block of T-code.
This M85 is a non-modal code.
M86 : TORQUE SKIP ACT
This code is used to skip the torque of moving axis.
As this code is a modal code until M87 command, only valid the sub-spindle with B-axis.
EX) G00 B-500.0 ;
M86 ;
G98 G31 P99 V-20.0 F100.0 ;
G01 B-500.0 ;
M87 ;
M87 : TORQUE SKIP CANCEL
This code is used to cancel torque skip function of M86.
M88 : C-AXIS LOW CLAMP
Specified to clamp the C-axis by low pressure.
Only valid the C-axis control.
M89 : C-AXIS HIGH CLAMP
Specified to clamp the C-axis by high pressure.
Only valid the C-axis control.
M90 : C-AXIS UNCLAMP
Specified to unclamp the C-axis.
Only valid the C-axis control.
M91,M92,M93,M94 : EXTERNAL M-CODE COMMAND (optional)
There code spare M code.
M98 : SUB-Prog. CALL
This code is used to enter a sub-program.
M99 : END OF SUB-PROGRAM
This code shows the end of a sub-program.
Executing M99 take the control back to the main program.

100

www.EngineeringBooksPdf.com
TRAINING

M103 : SUB-SPINDLE FORWARD DIRECTION

Specifies to start the sub spindle rotation in counterclockwise direction. S code should
be specified in the same block or previous.
If M103 code is specified when the sub-chuck is open, the sequence error will occur.
M104 : SUB-SPINDLE REVERSE DIRECTION
Specifies to start the sub spindle rotation in clockwise direction. S code should be speci-
fied in the same block or previous.
If M04 code is specified when the sub-chuck is open, the sequence error will occur.
M105 : SUB-SPINDLE STOP
Specifies to stop the sub spindle rotation. Even M05 is specified, the command spindle
speed remains effective. Therefore, if M103 or M104 is specified again, the spindle will
rotate by the same speed as the previous speed.
M110 : PART CATCHER2 ADVANCE (optional)
This command moves the part catcher2 advance.
M111 : PART CATCHER2 RETRACT (optional)
This command moves the part catcher2 retract.
M114 : AIR BLOW FOR SUB SPINDLE (optional)
Air blow for sub spindle when M114 is commanded.
M119 : SUB-SPINDLE ORIENTATION (optional)
This code stops sub-spindle at fixed angle.
M119 Sxxx : sub-spindle multi orientation (ORIENTATION “B”)
When M19 code and S code should be specified in the same block, the spindle tops
position is determined by S code.
M131 : INTERLOCK BY-PASS (SUB-SPINDLE)
This code is used when cycle start valid on sub spindle unclamp.
M163 : SUB-SPINDLE CW & COOLANT ON
Simultaneous start of sub spindle forward rotation and coolant.
Spindle forward and coolant are preformed by one(M163) command. Coolant comes out
only when operation panel switch is “on”.
M164 : SUB-SPINDLE CW & COOLANT ON
Simultaneous start of sub spindle forward rotation and coolant.
Spindle forward and coolant are preformed by one(M164) command. Coolant comes out
only when operation panel switch is “on”.
M165 : SUB-SPINDLE & COOLANT STOP
The sub spindle rotation & coolant is stopped by one command.
M168 : SUB-SPINDLE CLAMP
Specifies to open the sub-chuck automatically such as bar work.

101

www.EngineeringBooksPdf.com
TRAINING

M169 : SUB-SPINDLE UNCLAMP

Specified to close the sub-chuck automatically such as bar work.
M203 : FORWARD SYNCHRONOUS COMMAND
Main and sub spindle start simultaneously for forward rotation.
It is synchronized with forward rotation of main and sub spindle.
M204 : REVERSE SYNCHRONOUS COMMAND
Main and sub spindle start simultaneously for reverse rotation.
It is synchronized with reverse rotation of main and sub spindle.
M205 : SYNCHRONOUS STOP
The synchronous rotation of main and sub spindle is stop.
M206 : SPINDLE ROTATION RELEASE
Specified to release the speed control of main and sub spindle.
If you want to the main and sub spindle is rotate by difference rpm, M206 is commanded before
S-code. Spindle override on operating panel valid last selected spindle.
EX) M03 S1000 ;
M206 ;
M103 S500 ;

102

www.EngineeringBooksPdf.com