Installation Guide

English

Before Starting
1. This set is exclusively for use in cars with a
Car battery negative ground, 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “ ” terminal
before starting. This is to prevent short circuits
during installation.

Package Content
Source unit.................................................1 Flush mount bolts(M5x6)............................8
Wire connector...........................................1 Hexagon Head Screw(M5x6).....................8
GPS antenna..............................................1 Rear Stud Bolt............................................1
CLAMP for GPS antenna’s cable...............3 Rubber Parts..............................................1
DOUBLE FACE TAPE for GPS Antenna...1 AV cable.....................................................1
Remote control unit....................................1 Line out cable.............................................1
Battery (CR2025).......................................1 Rear Zone out cable...................................1
(Installed in remote control) SWC cable.................................................1
Cleaning cloth.............................................1 DAB cable..................................................1
Warranty Card............................................1 External Microphone cable.........................1
Quick Start Guide.......................................1 Camera Visual IN AUX2 cable...................1
Owner’s manual (CD-R).............................1 USB cable..................................................1
Electro tap..................................................2

Cautions On Installation

1. Prepare all articles necessary for installing

the main unit before starting. Max. 30°

2. Install the unit within 30° of the horizontal

plane.
Chassis
3. If you have to do any modification on the
Damage
car body, such as drilling holes, consult
your car dealer beforehand.

4. Use the included screws for installation.

Using other screws can cause damage.
Max. 6 mm (M5 screw)

5. This unit has a fan motor in the back

Fan motor vent
of the main unit so as not to raise the
temperature in the source unit. When
the fan motor vent is covered with cords
or mounting bracket, it may cause a
malfunction. Be sure not to cover it when
wiring cords.

14 NX502E
Installation Guide

English
Installing The Main Unit
This unit is designed for fixed installation in the dashboard.
1. When installing the main unit in NISSAN vehicles, use the parts attached to the unit (see “
NISSAN”). When installing the main unit in TOYOTA vehicles, use the parts attached to the
vehicle (see “ TOYOTA”).
2. Wire as shown in “Wire Connection”.
3. Reassemble and secure the unit in the dashboard and set the face panel and center panel.

Mounting Screw Holes (Side View of the Main Unit)

NISSAN TOYOTA

NISSAN

6-Spacer (thickness: 1 mm)

6-Flat head screw (M5 × 6)

(attached to the main unit)

Mounting bracket
(1 pair for the left and right sides)

TOYOTA

8-Hexagonal screw (M5 × 6)

Mounting bracket
Center Panel *1 (1 pair for the left and right sides)
*2

Screws marked and mounting bracket are attached to the vehicle.

NX502E 15
 Installation Guide
English

Note:
*1 Some panel openings are too small for the unit depending on the vehicle type and model. In
such a case, trim the upper and lower sides of the panel frame by about 0.5 to 1.5 mm so the
unit can be inserted smoothly.
*2 If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or
similar tool.

Vehicles other than NISSAN and TOYOTA

In some cases the center panel may require modification. (Trimming, filling, etc.)

Typical Mounting Brackets

In some cases the center panel may require modification. (Trimming, filling, etc.)

Example 1-3

Affix the screws to the marks.

Cautions On Wiring
• Be sure to turn the power off before wiring. Be particularly careful where you route the wires.
• Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires.
• If the fuse should blow, check to see if the wiring is correct. If a fuse is blown, replace it with a
new one of the same specification as the original.
• To replace the fuse, remove the old fuse of the power supply cord and insert the new one.
Note:
• There are various types of fuse holder. Do not let the battery side touch other metal parts.

Fuse (15A FUSE)

Fuse holder

• After the connection, fix the cord by a clamp or insulation tape for protection.

16 NX502E
Installation Guide

English
Installing The GPS Antenna

WARNING
• Do not install the GPS antenna in a place where it may interfere with the operation of the
airbag or hinder the driver’s visual range.
• Do not use the navigation system with the GPS antenna cord cut off. The power cables in the
cord may be short-circuited.

Note:
• T
 he supplied GPS antenna is for installing inside the vehicle. Do not install it outside the
vehicle.
• Install the GPS antenna more than 50 cm away from the main unit, other audio devices such
as CD player, and a radar detector. If it is installed near these devices, GPS reception may be
impaired.
• To improve the GPS signal reception, install the GPS antenna horizontally on a flat plane.
• Do not wax or paint the cover of the GPS antenna. This may reduce the performance of the
GPS antenna.
• Install the GPS antenna at least 10 cm away from the windshield.
• Wipe off the dirt of the mounting surface before installing the GPS antenna.

• Mount the GPS antenna.

Stick it surely on a flat plane of
the passengerside dashboard
GPS antenna
where GPS signal interruption is
minimized.
• Wire the GPS antenna cord.
Fasten the cord using the cord
holders.

Cord holder

Double-sided tape

• Stick the double-sided tape to the bottom

face of the GPS antenna.
Bottom face of the GPS antenna

NX502E 17
 Installation Guide
NX502E
English

Wire Connection
GPS Antenna
Antenna
(Black)
External Microphone
(Black)
Black Connection
(Black)
Black

(Black)

C
Radio Antenna
Antenna
B
1
2 A
3 1
4 2
5 3
6 4
7 5
8 6
7
8
Refer
Referto
to next page.
next page.

iPod/iPhone ®
iPod/iPhone

Red
Red

AUX IN 2
White
Video Out
Out
Black
VISUAL IN CCA-750
CCA-750(sold separately)
(sold separately)
Yellow

Black
Black
CAMERA Yellow
Yellow Video Out
Out
Rear Vision
Rear VisionCamera
Camera

Gray Gray
Gray
Steering
Steering Wheel
Wheel Remote
Remote Control
Control Terminal
Terminal

Black Yellow
Yellow
Black
VIDEO OUT
VIDEO OUT Video
Video In
In
Red
Red
Green
Green Rear
Rear Zone
Zone
Monitor
Monitor
2 ZONE
ZONE OUT
OUT
White Audio In
Audio In

Black Black
Black

DAB

DAB302E
DAB302E(sold separately)
(sold separately)

Red Line Out

Gray
Gray
Front Right
Right
Line Out
White
White Front Left
Left

Red Line Out

Out
Black
Black
Rear Right
Right
Line Out
Out
White
White Rear Left
Left

White
White 6-Channel Amplifier
6-Channel Amplifier
Purple
Purple Subwoofer
Subwoofer 11
Subwoofer
Subwoofer 22
Red
Black
USB
USB connector
connector
or
or
USB Memory
USB Memory

18 NX502E
Installation Guide

English
B
18 Rear left - 1
16 Rear left + 3
14 Front left - 5
12 Front left + 7
10 Front right +
8 Front right - 2
6 Rear right + 4
4 Rear right - 6
2 Battery + Fuse 15A 8

C
A
17 Reverse 1
15 Parking 3
13 5
11 ACC + 7
9 AUTO ANT
7 AMP Remote 2
5 Illumination 4
3 Phone Mute 6
1 Groundd 8

Function
Location
Connector A Connector B
Rear right (+) / Purple
Rear right (-) / Purple with black stripe
Front right (+) / Gray
Battery 12V(+) / Yellow Front right (-) / Gray with black stripe
Auto Antenna / Blue Front left (+) / White
Illumination / Orange with white stripe Front left (-) / White with black stripe
ACC+ / Red Rear left (+) / Green
Ground / Black Rear left (-) / Green with black stripe

Yellow Yellow

Red Red

VW, Audi

NX502E 19
 Installation Guide
English

Note:
*1 Connect to the AUX audio input terminal and the iPod video input terminal. (Audio connection
is required only when [Analog] is selected for the iPod output signal. See Owner’s Manual.)
*2 In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory
<<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory.
*3 When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the
<<Remote>> output.
Disconnect the <<blue/white>> wire and insulate the front ends of this cord. A breakdown may
occur if the cord is not disconnected, or front ends are not insulated.

Connecting the parking brake cord

Connect the cord to parking brake lamp ground in the meter panel.
Note:
• C
 onnecting the parking brake cord to lamp ground allows you to watch video images when
the parking brake is engaged.
• When the parking brake cord is not connected, the monitor will not display video images.

Parking brake lamp

cord to battery

Parking brake
Electro-tap

Parking brake signal cord

Parking brake cord (Grass-green)

Parking brake signal cord

Stopper
Parking brake cord (Grass-green)

20 NX502E