Scribd
Upload
76 views

Shear Strength Controls 21.65 Kips/bolt: Section at A

This document summarizes the design of a bolted connection for a 38.3 foot long tension member that must resist a load of 78 kips. It determines that 4 bolts of 7/8 inch diameter are needed to resist the load through shear and bearing strength calculations. Minimum bolt spacing of 3 inches and edge distance of 1.5 inches are specified. A 2L5x3x1/2LLBB shape is selected for the tension member with bolts placed in the long leg at a gauge of 3 inches. Calculations confirm this design meets the strength requirements.

Uploaded by

maheshbandham
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
76 views

Shear Strength Controls 21.65 Kips/bolt: Section at A

This document summarizes the design of a bolted connection for a 38.3 foot long tension member that must resist a load of 78 kips. It determines that 4 bolts of 7/8 inch diameter are needed to resist the load through shear and bearing strength calculations. Minimum bolt spacing of 3 inches and edge distance of 1.5 inches are specified. A 2L5x3x1/2LLBB shape is selected for the tension member with bolts placed in the long leg at a gauge of 3 inches. Calculations confirm this design meets the strength requirements.

Uploaded by

maheshbandham
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 4

PROJECT: STEEL BUILDING DESIGN CASE STUDY

SUBJECT: Tension member design. Bolted connection. SHEET 101 of 131


Connection for a 38.3 foot long tension member that has to resist 78 kips of already factored load.
No slip is permitted, so this connection is slip critical.
f t = resistance factor relating to tensile strength
Ag = gross cross-sectional area
Ae = U*An
U = reduction coefficient
Fy = specified (ASTM) minimum yield stress
Fu = specified (ASTM) minimum tensile strength
d = diameter of the bolt
An = net area
Rn = strength
Rstr = slip critical strength
Lc = distance from edge of hole to edge of connected part
t = thickness of connected part
Ab = nominal bolt area
Pu = factored load to be resisted
Fv = ultimate shearing strength
m = mean slip coefficient (coefficient of static friction)
Tb = minimum fastener tension
Agv = gross area acted upon by shear
Agt = gross area acted upon by tension
Anv = net area acted upon by shear
Ant = net area acted upon by tension
Because the bolt size and layout will affect the net area of the tension member, we will begin with
the selection of the bolts. Use A325 bolts and A572 Grade 36 steel for both the tension member and
the gusset plate (standard holes).
Pu = 76 (kips)
t= 3/4 in f= 0.75
Fv = 48 (ksi)
m = 0.33
Fy = 36 (ksi)
Fu = 58.0 (ksi)
L = 38.3 (ft)

Section at A
A

TRY : 7/8 (in) bolts Tb = 39 (kips) from table J3.1 LRFD


Ab = 0.60 (in2) Ns = 2
Shear strength:
fRn= fFv Ab (assuming that the threads are in the shear plane)
fRn= 21.65 Kips/bolt
f Rstr = f (1.13 m Tb b Ns) f Rstr = 29.09 Kips/bolt

Shear strength controls f Rn = 21.65 Kips/bolt


Red font indicates user input
PROJECT: STEEL BUILDING DESIGN CASE STUDY
SUBJECT: Bolted connection SHEET 102 of 131

Number of bolts required = 3.51 bolts


Try = 4 bolts

Minimum spacing : the distance between centers of standard, oversized, or slotted holes, shall
not be less than 3d (from AISC J3.3).
s =3 d= 2.63 in
say, s = 3 in

Minimum edge distance : (from AISC table J3.4)


Le = 1.5 in

Ag req. ³ 2.34568 in2


U= 0.85 (from commentary to the AISC specification)
Ae req. ³ 1.74713 in2
An req. ³ 2.05544 in2

minimum radius of gyration:


r min = 1.532 in

TRY 2L5x3x1/2LLBB
bolts placed in the long leg at the usual gage distance (check LRFD page 10-10)
usual gage = 3 in
Ag = #N/A in2 > 2.35 in2 #N/A
r = #N/A in > 1.53 in #N/A
t = #N/A in
An = #N/A in2 > 2.05544 in2 #N/A
x = 0.736 in
U = 0.91822 < 0.9 use U = 0.9
Ae = #N/A in2 > 1.74713 in2 #N/A
Check Bearing strength:

for bearing strength computation use a hole diameter of h = 15/16 in


f Rn = f (1.2 Lc t Fu) if Lc < 2 d
f Rn = f (2.4 d t Fu) if Lc > 2 d

For the hole nearest the edge of the member :


Lc = 1.03 in
2d= 1.75 in f Rn = #N/A kips/bolt
For the other holes:
Lc = 2.06 in
2d= 1.75 in f Rn = #N/A kips/bolt
Total bearing strength of the connection :

f Rn = #N/A kips > 76 kips #N/A


Red font indicates user input
PROJECT: STEEL BUILDING DESIGN CASE STUDY
SUBJECT: Bolted connection SHEET 103 of 131

Check Block shear:

Shear areas:
Agv = #N/A in2
Anv = #N/A in2

Tension areas:
Agt = #N/A in2
Ant = #N/A in2

Shear rupture design strength fVn: LRFD J4-1


f(.6*Fu)*Anv = #N/A kips

Tension rupture design strength fTn: LRFD J4-2


fFu*Ant = #N/A kips

The larger fracture term controls: #N/A

Block shear strength:

f Rn = #N/A kips < #N/A


f Rn = #N/A kips > Pu/2 = 38 kips #N/A

Le = 1.5 in
Le = 1.5 in s= 3 in.

g= 3 in

Use a 2L5x3x1/2LLBB with the long leg connected.


Use 4 7/8 in. A325 bolts.
Red font indicates user input

You might also like