Design and Modeling of Pull Rod and Push Rod Suspension System
Uploaded by
Editor IJTSRDDesign and Modeling of Pull Rod and Push Rod Suspension System
Uploaded by
Editor IJTSRDInternational Journal of Trend in Scientific Research and Development (IJTSRD)
Volume: 3 | Issue: 3 | Mar-Apr 2019 Available Online: www.ijtsrd.com e-ISSN: 2456 - 6470
Design and Modeling of Pull
Rod & Push Rod Suspension System
Sateesh Kumar Revoor1, Mittapally Nikhil2, Jatothu Sucharitha2, D. Anil2
1Assistant
Professor, 2Student
1,2Mechanical Department, GNIT Guru Nanak Institute of Technology, Hyderabad, India
How to cite this paper: Sateesh Kumar ABSTRACT
Revoor | Mittapally Nikhil | Jatothu The main criterion of this project is to design a suspension system practically to
Sucharitha | D. Anil "Design and a student formula vehicle and for systems, now loads are distributed to front and
Modeling of Pull Rod & Push Rod rear side. The stiffness of the spring is calculated by considering front and rear
Suspension System" Published in loads. The design of the spring, dash pot, rocker arms and push rod were done
International Journal of Trend in by LOTUS SHARK and modelling of these is done in SOLIDWORKS software.
Scientific Research and Development Later, the assembly of all parts and mono spring rocker arm front suspension
(ijtsrd), ISSN: 2456- system were designed racing cars. The dynamic loads are to be considered for
6470, Volume-3 | the design of wheel assembly, frame, and transmission, steering and braking.
Issue-3, April 2019,
pp.1074-1077, URL:
https://www.ijtsrd.c Keywords: Rocker Arm, Dash Pot, Push rod and Pull rod and Lotus Shark
om/papers/ijtsrd23
263.pdf IJTSRD23263
Copyright © 2019 by author(s) and
International Journal of Trend in
Scientific Research and Development
Journal. This is an Open Access article
distributed under
the terms of the
Creative Commons
Attribution License (CC BY 4.0)
(http://creativecommons.org/licenses/
by/4.0)
I. Introduction 1. Push Rod
In push rod suspension arm as shown in Fig.1. is usually at a
45 degree angle the bodywork/tyre in an F1 car. When the
car goes over a bump the movement is transffered throuh
the tyre and rim to the suspension arm, this then transfer the
loads into the “actual” suspension [1].
2. Pull Rod
Pull-rod suspension as shown in Fig.1. is literally just push-
rod turned upside down, they take all the internal
suspension parts and flip them upside down, then mount
them as low in the chasis as possible to help witrh centre of
gravity. This also means that the suspension arm as shown in
Fig.2. can be mounted down near horizontal with respect to
the road which is much better aerodynamically [2].
II. DESIGN OF PULL PUSH ROD SUSPENSION
Fig.1. Front View of Pull or Push Rod Suspension 1. LOTUS SHARK SUSPENSION DESIGN
Fig.2. Rocker Arm
Fig.3. Suspension Design in Lotus Shark
@ IJTSRD | Unique Paper ID – IJTSRD23263 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 1074
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
A market leading application for suspension modelling and 2.1 Calculation of Spring
design as shown in Fig.3. from the world-leaders in vehicle Design of spring
ride and handling; the lotus suspension analysis SHARK Design Considerations
module is a suspension geometric and kinematic modelling Spring Material: Stain less steel
tool, with a user- friendly interface which makes it easy to Larger diameter D=50mm
apply changes to proposed geometry and instantaneously Minor diameter (or) wire diameter d = 6mm
assess their impact trough the graphical results as shown in
Fig.4, Fig.5 and Fig.6. Material properties
Ultimate strength=505Mpa
Modulus of elasticity=193Gpa
Poisson ratio=0.29
Shear modulus=77Gpa
Out side diameter of a spring
D1=D+d
=50+6
= 56
Inner diameter of a spring
D2=D-d
=50-6
=44
Fig.4. Camber Graph
Spring index C =
= = 8.3333
Correction Factor
Kw = + =
=1.1773039
Maximum shear stress in the spring wire
F = 856.278 ≈ 900 N
Fig.5. Caster Graph Stiffness factor
K=21.40625 N/mm
No. of turns of coil
N = 6.731 ≈ 7 no.
Damper travel = 50mm
Modeling of spring designed as shown in Fig.7. according the
above calculations. And fabricated by the cold drawn process
Fig.6. King-Pin Inclination
and assembled to the dash pot.
2. Solid Works for Modeling
3D model of suspension components in modeling software’s,
we used SOLIDFWORKS for modeling of componenets. The
3D coordinate hard points are drawn from the suspensiuon
software called LOTUS SHARK. Next the reference plane on
which the sketch will be applied according to modeling tools
required to model. Finallythe parameters of the sketch such
as number of iterations and suppressed occurrences are
defined. In modeling the suspension system components
Fig.7. Spring And Dashpot Assembly
@ IJTSRD | Unique Paper ID - IJTSRD23263 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 1075
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
Rocker Arm
Rocker arm is a kinematic link which varies the motion
according to the motion ratio required for the suspension.
Dcesigns of rocker arm, thed inputs are drawn from the
software. Modeling of rocker are designed in solid works as
shown in Fig.8 and Fig.9. by using the specific tools for
modeling.
Considering the material for the rocker is stainless steel. And
fabricated by using the TIG welding process according the
design.
Fig.10. Front View of Pushrod Suspension
Fig.8. Free Body Diagram of Rocker Arm
Fig.11. Iso Metric View of Pushrod Suspension
Fig.12. Side View of Pushrod Suspension
Fig.9. Rocker Arm Design
Assembly
An assembly is a model comprised of multiple parts models.
It is mainly used to mode the interaction between different
parts. Assemblies can be used to check how parts fit
together, detect collisions, and show the interaction between
parts and more. To create an assembly, Parts files are
imported into the assembly drawing. Once there the parts
are aligned oriented using relations. Parts can be related
through any of their individual features using a variety of
relation tools, e.g. axial align, planar align, connect etc.
Assemblies can also contain other ‘sub-assemblies within
them which are treated in the same fashion as individual
parts, push rod suspension assembly as shown in Fig.10,
Fig.11, Fig.12 and Fig.13 [3]. Fig.13. Top View of Pushrod Suspension System
@ IJTSRD | Unique Paper ID - IJTSRD23263 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 1076
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
Wheel Assembly designing and modeling the pull push rod suspension
The assembled wheel as shown in Fig.14 and Fig.15 consists system. IN the thesis suspension properties like camber,
of certain parts included which are alignedf in sequential caster and kingpin inclination angle was explained and what
order. effects on the overall handling of the car they have. How the
Tyres design could be as possible without sacrificing performance
Whel Hub is explained. Lowering the Centre of Gravity by using pull-
Knuckle/Upright rod suspension instead of push rod suspension. Designing
Disc active suspension system and the possibility of having no
Brake caliper anti. After the design of each component of the suspension
Astub axle system, an assembly was created to verify the design and
Hub bearings that no interference was between components.
IV. ACKNOWLEDGMENT
I owe my immense thanks to my Dr. B. Vijaya Kumar,
Professor and Head of the department, Guru Nanak Institute
of Technology for his encouragement at every stage of this
Endeavour.
I extended my deep sense of gratitude to the principal
Dr. S. Sreenatha Reddy, and the management of Guru
Nanak Institute of Technology for providing of the best
amenities to enable us to complete my project in stipulated
time.
Fig.14. Exploded View of Wheel Assembly
Finally, I am very thankful my parents, friend’s faculty and
other of the department of Mechanical Engineering for the
constant support for a completion of this project.
V. REFERENCES
[1] Dishant, Er. Parminder Singh, Er. Mohit Sharma “DESIGN
AND ANALYSIS OF PUSH ROD AND ROCKER ARM
SUSPENSION” International Journal of mechanical
engineering, volume 114, pp. 465-476.
[2] Dr. Porga Kalita “Design and Optimization of a SAE Baja
Chasis” International Journal of Mechanical Engineering,
Volume 3, Issue 5, June 2016.
Fig.15. Wheel Assembly of Push Rod Suspension [3] Smit Thakkar “Research Paper on Design Modification
and Analysis of Automobile wheel Rim” IJSRD –
III. CONCLUSION International Journal for Scientific Research
As the main objectives of this thesis were to gain a better &Development, Volume 3, Issue 3,2015.
understanding of how pull push rod suspension systems
work and combine theory and practical knowledge by [4] Lotus Suspension Analysis v4.03.
@ IJTSRD | Unique Paper ID - IJTSRD23263 | Volume – 3 | Issue – 3 | Mar-Apr 2019 Page: 1077
You might also like
- No ratings yet"Advancements in Machine Learning for Early Detection of Plant Diseases by Gayatri Rahangdale | Supesh Falke | Gauri Bharti | Shweta Dewalkar | Prof. Anupam Chaube | Prof. Rina Shirpurkar Link To Download Paper: https://www.ijtsrd.com/other-scientific-research-area/other/69417/advancements-in-machine-learning-for-early-detection-of-plant-diseases/gayatri-rahangdale #callforpaperinternationaljournal #ugclistofjournals #bestinternationaljournal Plant detection is a critical task in agricultural automation and environmental monitoring. It involves identifying and classifying plant species, diseases, or other relevant plant characteristics using various techniques, such as image processing, machine learning, and remote sensing. Advances in computer vision and artificial intelligence have enabled the development of robust plant detection systems capable of analyzing vast amounts of data in real time. These systems can be employed for applications such as precision agriculture, where acc9 pages
