User’s Manual

TECRA A10
TECRA S10
TECRA M10
Satellite Pro S300

computers.toshiba-europe.com
TECRA A10/S10/M10/SatellitePro S300

Table of Contents

Preface
General Precautions
Chapter 1 Getting Started
Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Restarting the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
Chapter 2 The Grand Tour
Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Back. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17
Chapter 3 Hardware, Utilities and Options
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Utilities and Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Optional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-36
Chapter 4 Operating Basics
TOSHIBA Dual Pointing Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Using the TOSHIBA Face Recognition. . . . . . . . . . . . . . . . . . . . . . . .4-12
Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-15
Writing CDs on DVD-ROM & CD-R/RW drives . . . . . . . . . . . . . . . . . .4-19

ii User’s Manual
 TECRA A10/S10/M10/SatellitePro S300

Writing CD/DVDs on DVD Super Multi drives . . . . . . . . . . . . . . . . . 4-22

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37
Computer Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . 4-41
Using the TOSHIBA USB Sleep and Charge Utility . . . . . . . . . . . . . 4-43
Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45
Chapter 5 The Keyboard
Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Chapter 6 Power and Power-Up Modes
Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Monitoring of power condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Chapter 7 HW Setup
Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Chapter 8 Troubleshooting
Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28
Appendix A Specifications
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Appendix B Display Controller and Video mode
Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Video mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Appendix C Wireless LAN
Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Supported Frequency Sub-bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

User’s Manual iii

TECRA A10/S10/M10/SatellitePro S300

Appendix D Bluetooth wireless technology Interoperability

Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . D-2
Regulatory statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
Using Bluetooth Adaptor from TOSHIBA equipment in Japan . . . . D-4
Appendix E AC Power Cord and Connectors
Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
Appendix F TOSHIBA Anti-theft Protection Timer
Appendix G TOSHIBA PC Health Monitor
Starting the TOSHIBA PC Health Monitor . . . . . . . . . . . . . . . . . . . . . G-2
If a TOSHIBA PC Health Monitor message is displayed. . . . . . . . . . G-2
Cleaning the cooling module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3
Appendix H Legal Footnotes
Appendix I If your computer is stolen
Glossary
Index

iv User’s Manual
 TECRA A10/S10/M10/SatellitePro S300

Copyright
© 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.
TOSHIBA TECRA A10/S10/M10/Satellite Pro S300 Portable Personal
Computer User’s Manual
First edition June 2008
Copyright authority for music, movies, computer programs, databases and
other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author’s rights and is subject
to civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.

Disclaimer
This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
TECRA A10/S10/M10/Satellite Pro S300 Portable Personal Computer at
the time of this manual’s production. However, succeeding computers and
manuals are subject to change without notice. TOSHIBA assumes no
liability for damages incurred directly or indirectly from errors, omissions or
discrepancies between the computer and the manual.

Trademarks
IBM is a registered trademark and IBM PC is a trademark of International
Business Machines Corporation.
Intel, Intel SpeedStep, Intel Core and Centrino are trademarks or registered
trademarks of Intel Corporation.
Windows, Microsoft and Windows Vista are registered trademarks of
Microsoft Corporation.
Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.
Photo CD is a trademark of Eastman Kodak Company.
Memory Stick, Memory Stick PRO, Memory Stick PRO Duo and i.LINK are
trademarks or registered trademarks of Sony Corporation.
ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Secure Digital and SD are trademarks of SD Card Association.
MultiMediaCard and MMC are trademarks of MultiMediaCard Association.

User’s Manual v
TECRA A10/S10/M10/SatellitePro S300

xD-Picture Card is a trademark of FUJIFILM Corporation.

Other trademarks and registered trademarks not listed above may be used
in this manual.

EU Declaration of Conformity
This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe
GmbH, Hammfelddamm 8, 41460 Neuss, Germany.
The complete and official EU Declaration of Conformity can be found on
TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.

CE compliance
This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive
89/336/EEC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 1999/5/EC in case of implemented
telecommunication accessories and the Low Voltage Directive
73/23/EEC for the supplied power adapter.
This product and the original options are designed to observe the related
EMC (Electromagnetic Compatibility) and safety standards. However,
TOSHIBA cannot guarantee that this product still observes these EMC
standards if options or cables not produced by TOSHIBA are connected or
implemented. In this case the persons who have connected / implemented
those options / cables have to provide assurance that the system (PC plus
options / cables) still fulfils the required standards. To avoid general EMC
problems, the following guidance should be noted:
■ Only CE marked options should be connected / implemented
Only best shielded cables should be connected

GOST

vi User’s Manual
 TECRA A10/S10/M10/SatellitePro S300

Modem warning notice

This information is applicable to the models equipped with a built-in

modem.

Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for
pan-European single terminal connection to the Public Switched Telephone
Network (PSTN).
However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.
In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.
Germany ATAAB AN005,AN006,AN007,AN009,AN010
and DE03,04,05,08,09,12,14,17
Greece ATAAB AN005,AN006 and GR01,02,03,04
Portugal ATAAB AN001,005,006,007,011 and
P03,04,08,10
Spain ATAAB AN005,007,012, and ES01
Switzerland ATAAB AN002
All other ATAAB AN003,004
countries/regions
Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

User’s Manual vii

TECRA A10/S10/M10/SatellitePro S300

Following information is only for EU-member States

Disposal of products
The crossed out wheeled dust bin symbol indicates that products must be
collected and disposed of separately from household waste. Integrated
batteries and accumulators can be disposed of with the product. They will
be separated at the recycling centres.
The black bar indicates that the product was placed on the market after
August 13, 2005.
By participating in separate collection of products and batteries, you will
help to assure the proper disposal of products and batteries and thus help
to prevent potential negative consequences for the environment and
human health.
For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from
household waste.
If the battery or accumulator contains more than the specified values of
Pb, Hg, Cd lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery
Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury
(Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust
bin symbol.
By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

This symbol may not stick depending on the country and region where you
purchased.

viii User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Disposing of the computer and the computer’s batteries

■ Discard this computer in accordance with applicable laws and
regulations. For further information, contact your local government.
■ This computer contains rechargeable batteries. After repeated use, the
batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.
■ Please be kind to our shared environment. Check with your local
government authority for details regarding where to recycle old batteries
or how to dispose of them properly. This product contains mercury.
Disposal of this material may be regulated due to environmental
considerations. For disposal, reuse or recycling information, please
contact your local government.

ENERGY STAR® Program

Your computer model may be Energy Star® qualified. If the model you
purchased is compliant, it is labeled with the ENERGY STAR logo on the
computer and the following information applies.
TOSHIBA is a partner in the Environmental Protection Agency’s (EPA)
ENERGY STAR® Program and has designed this computer to meet the
latest ENERGY STAR® guidelines for energy efficiency. Your computer
ships with the power management options preset to a configuration that will
provide the most stable operating environment and optimum system
performance for both AC power and battery modes.
To conserve energy, your computer is set to enter the low-power Sleep
mode which shuts down the system and display within 15 minutes of
inactivity in AC power mode. TOSHIBA recommends that you leave this
and other energy saving features active, so that your computer will operate
at its maximum energy efficiency. You can wake the computer from Sleep
mode by pressing the power button.
Products that earn the ENERGY STAR® prevent greenhouse gas emissions
by meeting strict energy efficiency guidelines set by the US EPA and the EU
Commission. According to the EPA, a computer meeting the new ENERGY
STAR® specifications will use between 20% and 50% less energy
depending on how it is used.
Visit http://www.eu-energystar.org or http://www.energystar.gov for more
information regarding the ENERGY STAR Program.
Visit http://www.energystar.gov or
http://www.energystar.gov/powermanagement for more information
regarding the ENERGY STAR Program.

User’s Manual ix
TECRA A10/S10/M10/SatellitePro S300

Optical disc drive standards

TOSHIBA TECRA A10/S10/M10/Satellite Pro S300 computer is shipped
with one of the following drives preinstalled: DVD Super Multi (+-R DL),
DVD-ROM & CD-R/RW or DVD-ROM.
■ The drive employs a laser system. To ensure proper use of this
product, please read this instruction manual carefully and retain for
future reference.
Should the unit ever require maintenance, contact an authorized
service location.
■ Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure
■ To prevent direct exposure to the laser beam, do not try to open the
enclosure.

The drive has one of the following labels:

CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE1
KLASS 1 LASER APPARAT

Before it is shipped, the Class 1 Laser is certified to meet the United States
Chapter 21 Standards of the Department of Health and Human Services
(DHHS 21 CFR).
For any other country, the drive is certified to meet the Class 1 Laser
standards of IEC825 and EN60825.
This computer is equipped with one of the optical drives in the following list:

Manufacturer Type

TEAC DVD Super Multi (±R Double Layer) DV-W28S

Panasonic DVD Super Multi (±R Double Layer) UJ870

Communications

TEAC DVD-ROM & CD-R/RW drive DW-224S

TEAC DVD-ROM drive DV-28S

x User’s Manual
 TECRA A10/S10/M10/SatellitePro S300

Important notice
Copyrighted works including, but not limited to music, video, computer
program, databases are protected by copyright laws. Unless specifically
permitted under applicable copyright laws, you cannot copy, modify, assign,
transmit or otherwise dispose of any copyrighted work with the consent of
the owner of the copyright. Please take notice that unauthorized copying,
modification, assignment, transmission and disposition may be subject to
claims for damages and penalties.
■ Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
■ Do not use the telephone to report a gas leak in the vicinity of the leak.
■ Use only the power cord indicated in this manual.
■ Replace only with the same or equivalent type battery recommended by
the manufacturer.
■ Dispose of used batteries according to the manufacturer’s instructions.
Use only the battery pack that came with the computer or an optional
battery pack. Use of wrong battery could damage your computer.

TOSHIBA assumes no liability for any damage in such case.

User’s Manual xi
TECRA A10/S10/M10/SatellitePro S300

Preface

Congratulations on your purchase of the TECRA A10/S10/M10/Satellite

Pro S300 series computer. This powerful notebook computer provides
excellent expansion capability, includes multimedia functionality, and is
designed to provide years of reliable, high-performance computing.
This manual tells how to set up and begin using your TECRA A10/S10/
M10/Satellite Pro S300 series computer. It also provides detailed
information on configuring your computer, basic operations and care, using
optional devices and troubleshooting.
If you are a new user of computers or if you’re new to portable computing,
first read over the Chapter 1, Getting Started and Chapter 3, Hardware,
Utilities and Options chapters to familiarize yourself with the computer’s
features, components and accessory devices. Then read Chapter 1,
Getting Started for step-by-step instructions on setting up your computer.
If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to read the Special
features section in Chapter 3, Hardware, Utilities and Options to learn
about features that are uncommon or unique to this computer, as well as
the section on Chapter 7, HW Setup, to understand how to setup and
configure these features.
Read Chapter 3, Hardware, Utilities and Options if connecting optional
products or external devices.

Conventions
This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

xii User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Icons
Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys
The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation
Some operations require you to simultaneously use two or more keys.
We identify such operations by the key top symbols separated by a plus
sign (+). For example, CTRL + C means you must hold down CTRL and at
the same time press C. If three keys are used, hold down the first two and
at the same time press the third.

ABC When procedures require an action such as

clicking an icon or entering text, the icon’s name
or the text you are to type in is represented in the
typeface you see to the left.

Display

Names of windows or icons or text generated by

S ABC the computer that appear on its display screen
are presented in the type face you see to the left.

Messages
Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.
Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Indicates a potentially hazardous situation, which could result in death or

serious injury, if you do not follow instructions.

User’s Manual xiii

TECRA A10/S10/M10/SatellitePro S300

Terminology
This term is defined in this document as follows:
Start The word “Start” refers to the “ ” button in
Microsoft® Windows Vista®.
HDD or Hard disk Some models are equipped with a “Solid State
drive Drive (SSD)” instead of a hard disk drive.
In this manual, the word “HDD” or “Hard disk
drive” also refers to the SSD unless otherwise
stated.

xiv User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and

withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.
Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Provide adequate ventilation

■ Always make sure your computer and AC adaptor have adequate
ventilation and are protected from overheating when the power is
turned on or when an AC adaptor is connected to a power outlet
(even if your computer is in Sleep Mode). In this condition, observe the
following:
■ Never cover your computer or AC adaptor with any object.
■ Never place your computer or AC adaptor near a heat source,
such as an electric blanket or heater.
■ Never cover or block the air vents including those located at the
base of the computer.
■ Always operate your computer on a hard flat surface. Using your
computer on a carpet or other soft material can block the vents.
■ Always provide sufficient space around the computer.
■ Overheating your computer or AC adaptor could cause system failure,
computer or AC adaptor damage or a fire, possibly resulting in serious
injury.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.
Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.

User’s Manual xv
TECRA A10/S10/M10/SatellitePro S300

To keep your computer in prime operating condition, protect your work

area from:
■ Dust, moisture, and direct sunlight.
■ Equipment that generates a strong electromagnetic field, such as
stereo speakers (other than speakers that are connected to the
computer) or speakerphones.
■ Rapid changes in temperature or humidity and sources of temperature
change such as air conditioner vents or heaters.
■ Extreme heat, cold, or humidity.
■ Liquids and corrosive chemicals.

Stress injury
Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Instruction Manual for
Safety and Comfort also includes information on work space design,
posture and lighting that can help reduce physical stress.

Heat injury
■ Avoid prolonged physical contact with the computer. If the computer is
used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest,
your skin might suffer a low-heat injury.
■ If the computer has been used for a long time, avoid direct contact with
the metal plate supporting the various interface ports as this can
become hot.
■ The surface of the AC adaptor can become hot when in use but this
condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.
■ Do not lay the AC adaptor on a material that is sensitive to heat as the
material could become damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer’s components or otherwise
cause it to malfunction.

xvi User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

PC Card overheating
Some PC Cards can become hot during prolonged use which may result in
errors or instability in the operation of the device in question. In addition,
you should also be careful when you remove a PC Card that has been
used for a long time.

Mobile phones
Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort.
Be sure to read it before using the computer.

User’s Manual xvii

TECRA A10/S10/M10/SatellitePro S300

xviii User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 1

Getting Started

This chapter provides an equipment checklist, and basic information to start

using your computer.
Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist
Carefully unpack your computer, taking care to save the box and packaging
materials for future use.
Hardware
Check to make sure you have all the following items:
■ TECRA A10/S10/M10/Satellite Pro S300 Portable Personal Computer
■ AC adaptor and power cord (2-pin plug or 3-pin plug)
■ Battery pack (Is included with some models)
■ Spare AccuPoint (pointing device) cap (Is included with some models)

User’s Manual 1-1

TECRA A10/S10/M10/SatellitePro S300

Software
The following Windows® operating system and utility software are pre-
installed.
■ Microsoft® Windows Vista™
■ TOSHIBA Value Added Package
■ TOSHIBA Recovery Disc Creator
■ TOSHIBA DVD Player
■ TOSHIBA SD Memory Utilities
■ TOSHIBA SD Memory Boot Utility
■ TOSHIBA Assist
■ TOSHIBA ConfigFree™
■ TOSHIBA HDD Protection
■ TOSHIBA Disc Creator
■ TOSHIBA Face Recognition*
■ TOSHIBA PC Health Monitor*
■ TOSHIBA USB Sleep and Charge Utility
■ Bluetooth Stack for Windows by Toshiba
■ CD/DVD Drive Acoustic Silencer
■ Fingerprint Utility
■ Windows Mobility Center
■ Online Manual
* Indicates software that is preinstalled with some models
Documentation
■ TECRA A10/S10/M10/Satellite Pro S300 User´s Manual
■ TECRA A10/S10/M10/Satellite Pro S300 Quickstart
■ Instruction Manual for Safety and Comfort
■ Warranty information
If any of the items are missing or damaged, contact your dealer
immediately.

1-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Getting Started

■ All users should be sure to read the section Starting up for the first time.
■ Be sure to read the enclosed Instruction Manual for Safety and Comfort
for information on the safe and proper use of this computer. It is
intended to help you be more comfortable and productive while using a
notebook computer. By following the recommendations in it you may
reduce your chance of developing a painful or disabling injury to your
hand, arms, shoulders or neck.

This section provides basic information to start using your computer.

It covers the following topics:
■ Connecting the AC adaptor
■ Opening the display
■ Turning on the power
■ Starting up for the first time
■ Turning off the power
■ Restarting the computer
■ System Recovery Options
■ Restoring the pre-installed software
■ Use a virus-check program and make sure it is updated regularly.
■ Never format storage media without checking its content - formatting
destroys all stored data.
■ It is a good idea to periodically back up the internal hard disk drive or
other main storage device to external media. General storage media is
not durable or stable over long periods of time and under certain
conditions may result in data loss.
■ Before you install a device or application, save any data in memory to
the hard disk drive or other storage media. Failure to do so may result
in the loss of data.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.
The AC adaptor can be connected to any power source supplying from
100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

User’s Manual 1-3

TECRA A10/S10/M10/SatellitePro S300

■ Always use the TOSHIBA AC adaptor that was included with your
computer, or use AC adaptors specified by TOSHIBA to avoid any risk
of fire or other damage to the computer. Use of an incompatible AC
adaptor could cause fire or damage to the computer possibly resulting
in serious injury. TOSHIBA assumes no liability for any damage caused
by use of an incompatible adaptor.
■ Never plug the AC adaptor into a power source that does not
correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.
■ Always use or purchase power cables that comply with the legal
voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.
■ The supplied power cord conforms to safety rules and regulations in
the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.
■ Do not use a 3-pin to 2-pin conversion plug.
■ When you connect the AC adaptor to the computer, always follow the
steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical charge
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.
■ Never place your computer or AC adaptor on a wooden surface,
furniture, or any other surface that could be marred by exposure to heat
since the computer base and AC adaptor’s surface increase in
temperature during normal use.
■ Always place your computer or AC adaptor on a flat and hard surface
that is resistant to heat damage.
Refer to the enclosed Instruction Manual for Safety and Comfort for
detailed precautions and handling instructions.

1-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

1. Connect the power cord to the AC adaptor.

Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer

depending on the model.

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the

back of the computer.

DC IN 15V jack

DC output plug

Figure 1-3 Connecting the DC output plug to the computer

3. Plug the power cord into a live wall outlet - the Battery and DC IN
indicators on the front of the computer should glow.

User’s Manual 1-5

TECRA A10/S10/M10/SatellitePro S300

Opening the display

The display panel can be opened to a wide range of angles for optimal
viewing.
While holding down the palm rest with one hand so that the main body of
the computer is not raised, slowly lift the display panel - this will allow the
angle of the display panel to be adjusted to provide optimum clarity.

Display panel

Figure 1-4 Opening the display panel

Use reasonable care when opening and closing the display panel.
Opening it vigorously or slamming it shut could damage the computer.

■ Be careful not to open the display panel too far as this could put stress
on the display panel’s hinges and cause damage.
■ Do not press or push on the display panel.
■ Do not lift the computer by the display panel.
■ Do not close the display panel with pens or any other objects left in
between the display panel and the keyboard.
■ When opening or closing the display panel, place one hand on the
palm rest to hold the computer in place and use the other hand to
slowly open or close the display panel (Do not use excessive force
when opening or closing the display panel).

1-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Turning on the power

This section describes how to turn on the power - the Power indicator will
then indicate the status. Please refer to the Monitoring of power condition
section in Chapter 6, Power and Power-Up Modes, for more information.
■ After you turn on the power for the first time, do not turn it off until you
have set up the operating system. Please refer to the section Starting
up for the first time for more information.
■ Volume cannot be adjusted during Windows Setup.

1. Open the display panel.

2. Press and hold the computer’s power button for two or three seconds.

Power button

Figure 1-5 Turning on the power

Starting up for the first time

The Microsoft Windows Vista Startup Screen will be the first screen
displayed when you turn on the power. Follow the on-screen instructions on
each screen in order to properly install the operating system.
When it is displayed, be sure to read the Software License Terms
carefully.

Turning off the power

The power can be turned off in one of three modes, either Shut Down
Mode, Hibernation Mode or Sleep Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and
the computer will boot to the operating system’s main screen the next time
it is turned on.
1. If you have entered data, either save it to the hard disk drive or to other
storage media.
2. Make sure all disk/disc activity has stopped before removing the
CD/DVD or floppy diskette.

User’s Manual 1-7

TECRA A10/S10/M10/SatellitePro S300

■ Make sure the Hard Disk Drive/Optical Disc Drive indicators are off.
If you turn off the power while a disk (disc) is being accessed, you may
lose data or damage the disk.
■ Never turn off the power while an application is running. Doing so could
cause loss of data.
■ Never turn off the power, disconnect an external storage device or remove
storage media during data read/write. Doing so can cause data loss.

3. Click Start.
4. Click the arrow button ( ) located in the power management buttons
( ) and select Shut Down from the menu.
5. Turn off any peripheral devices connected to your computer.
Do not turn the computer or peripheral devices back on immediately -
wait a short period to avoid any potential damage.

Sleep Mode
If you have to interrupt your work, you are able to turn off the power without
exiting from your software by placing the computer into Sleep Mode. In this
mode data is maintained in the computer’s main memory so that when you
turn on the power again, you can continue working right where you left off.
When you have to turn off your computer aboard an aircraft or in places
where electronic devices are regulated or controlled, always completely shut
down the computer. This includes turning off any wireless communication
switches or devices, and canceling settings that reactivate the computer
automatically, such as a timer recording function. Failure to completely shut
down the computer in this way could allow the operating system to reactivate
and run pre-programmed tasks or preserve unsaved data, which could
interfere with aviation or other systems, possibly causing serious injury.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in
Sleep Mode. The computer or the memory module could be damaged.
■ Do not remove the battery pack while the computer is in Sleep Mode
(unless the computer is connected to an AC power source). Data in
memory could be lost.

1-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options (to access it, Start
-> Control Panel -> System and Maintenance -> Power Options).
■ To restore the operation of the computer from Sleep Mode, press and
hold the power button or any key on the keyboard for a short amount of
time. Please note that keyboard keys can only be used if the Wake-up
on Keyboard option is enabled within the HW Setup utility.
■ If the computer enters Sleep Mode while a network application is
active, the application might not be restored when the computer is next
turned on and the system returns from Sleep Mode.
■ To prevent the computer from automatically entering Sleep Mode,
disable Sleep Mode within the Power Options (to access it, Start ->
Control Panel -> System and Maintenance -> Power Options).
■ To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:
■ Restores the previous working environment more rapidly than does the
Hibernation Mode feature.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the time period set by the System
Sleep Mode feature.
■ Allows the use of the panel power off feature.

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to

Chapter 5, The Keyboard, for further details.
You can enter Sleep Mode in one of four ways:
■ Click Start then click the power button ( ) located in the power
management buttons ( ).
Please note that this feature must be enabled within the Power Options
(to access it, click Start -> Control Panel -> System and Maintenance
-> Power Options).
■ Click Start then click the arrow button ( ) and select Sleep from the
menu.
■ Close the display panel. Please note that this feature must be enabled
within the Power Options (to access it, click Start -> Control Panel ->
System and Maintenance -> Power Options).
■ Press the power button. Please note that this feature must be enabled
within the Power Options (to access it, click Start -> Control Panel ->
System and Maintenance -> Power Options).

User’s Manual 1-9

TECRA A10/S10/M10/SatellitePro S300

When you turn the power back on, you can continue where you left when
you shut down the computer.
■ When the computer is in Sleep Mode, the power indicator will blink
orange.
■ If you are operating the computer on battery power, you can lengthen
the overall operating time by turning it off into Hibernation Mode -
Sleep Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:
■ Power is turned back on immediately after shutting down.
■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode
The Hibernation Mode feature saves the contents of memory to the hard
disk drive when the computer is turned off so that, the next time it is turned
on, the previous state is restored. Please note that the Hibernation Mode
feature does not save the status of any peripheral devices connected to the
computer.
■ Save your data. While entering Hibernation Mode, the computer saves
the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.
■ Data will be lost if you remove the battery or disconnect the AC adaptor
before the save is completed. Wait for the Hard Disk Drive indicator to
go out.
■ Do not install or remove a memory module while the computer is in
Hibernation Mode. Data will be lost.

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:
■ Saves data to the hard disk drive when the computer automatically
shuts down because of a low battery condition.
■ You can return to your previous working environment immediately when
you turn on the computer.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the time period set by the System
Hibernate feature.
■ Allows the use of the panel power off feature.

1-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer
to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click Start.
2. Click the arrow button ( ) in the power management buttons
( ) and select Hibernate from the menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically
when you press the power button or close the lid. In order to define these
settings, you can follow the steps as described below:
1. Click Start and click the Control Panel.
2. Click System and Maintenance and click Power Options.
3. Click Choose what the power button does or Choose what closing
the lid does.
4. Enable the desired Hibernation Mode settings for When I press the
power button and When I close the lid.
5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a
moment to save the current data in memory to the hard disk drive.
During this time, the Hard Disk Drive indicator will glow.
After you turn off the computer, and the content of memory has been saved
to the hard disk drive, turn off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

User’s Manual 1-11

TECRA A10/S10/M10/SatellitePro S300

Restarting the computer

Certain conditions require that you reset the computer, for example if:
■ You change certain computer settings.
■ An error occurs and the computer does not respond to your keyboard
commands.
If you need to restart the computer, there are three ways this can be
achieved:
■ Click Start then click the arrow button ( ) in the power management
buttons ( ) and select Restart from the menu.
■ Press CTRL, ALT and DEL simultaneously (once) to display the menu
window, then select Restart from the Shut down options.
■ Press the power button and hold it down for five seconds. Once the
computer has turned itself off, wait between ten and fifteen seconds
before turning the power on again by pressing the power button.

System Recovery Options

A hidden partition of approximately 1.5 GB is allocated on the hard disk
drive for the System Recovery Options. This partition stores files which can
be used to repair the system in the event of a problem.
The System Recovery Options feature will be unusable if this partition is
deleted.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when
shipped from the factory. The System Recovery Options menu includes
tools to repair startup problems, run diagnostics or restore the system.
You can see the more information about Startup Repair in Windows Help
and Support content.
The System Recovery Options can also be run manually to repair
problems.
1. Turn off the computer.
2. While holding the F8 key, turn the computer on again.
3. The Advanced Boot Options menu will be displayed. Use the arrow
keys to select Repair Your Computer and press ENTER.
4. Follow the on-screen instructions from this point onward.
The Window Vista Complete PC Backup feature can be used on Windows
Vista™ Business Edition and Ultimate Edition.

1-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Restoring the pre-installed Software

Depending on the model you purchased, different ways for restoring the
pre-installed software are offered:
■ Creating optical Recovery Discs
■ Restoring the pre-installed software from your created Recovery Discs.
■ Restoring the pre-installed software from the Recovery hard disk drive

Creating Optical Recovery Discs

This section describes how to create Recovery Discs.
■ Be sure to connect the AC adaptor when you create Recovery Discs.
■ Be sure to close all other software programs except the Recovery Disc
Creator.
■ Do not run software such as screen savers which can put a heavy load
on the CPU.
■ Operate the computer at full power.
■ Do not use power-saving features.
■ Do not write to the disc when the virus check software is running. Wait
for it to finish, then disable virus detection programs including any
software that checks files automatically in the background.
■ Do not use utilities, including those intended to enhance hard disk drive
access speed. They may cause unstable operation and damage data.
■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting
the disc.
■ Set the computer on a level surface and avoid places subjected to
vibrations such as airplanes, trains or cars.
■ Do not place your computer on unstable tables or any other unstable
surfaces.
A recovery image of the software on your computer is stored on the hard
disk drive, and can be copied to DVD media by using the following steps:
1. Have blank DVD media ready.
2. The application will allow you to choose from a variety of different media
onto which the recovery image can be copied including DVD-R,
DVD-RW, DVD+R, DVD+RW.
Please note that some of the above media may not be compatible with the
optical disc drive installed into your computer. You should therefore verify
the optical disc drive supports the blank media you have chosen before
proceeding.

3. Turn on your computer and allow it to load the Windows Vista®

operating system from the hard disk drive as normal.
4. Insert the first blank media into the optical disc drive tray.
5. Double click the Recovery Disc Creator icon on the Windows Vista®
desktop, or select the application from Start Menu.

User’s Manual 1-13

TECRA A10/S10/M10/SatellitePro S300

6. After Recovery Disc Creator starts, select the type of media and the title
you wish to copy, and then click the Create button.
7. Follow the on-screen instructions.
Your Recovery Discs will be created.

Restoring the pre-installed software from your created

Recovery Discs
Please set your BIOS to default before you recover your computer to the
factory state!

If the pre-installed files are damaged, you are able to use the Recovery
Discs you have created to restore the computer to the state it was in when
you originally received it. To perform this restoration, follow the steps
below:
When the sound mute feature has been activated by pressing the
FN + ESC key, be sure to disable this to allow sounds to be heard before
starting the restore process. Please refer to Chapter 5, The Keyboard, for
further details.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Load the Recovery Discs into the optical disc drive and turn off the
computer’s power.
2. While holding down F12 key on the keyboard, turn on your computer -
when the TOSHIBA logo screen appears, release the F12 key.
3. Use the cursors key to select the CD-ROM icon from the menu. Please
refer to the Boot Priority section in Chapter 7, HW Setup, for further
information.
4. A menu will be displayed from which you should follow the on-screen
instructions.

Restoring the pre-installed software from the Recovery

hard disk drive
Please set your BIOS to default before you recover your computer to the
factory state!
On your Data drive you may find a folder “HDDRecovery”. This folder
stores files which can be used to recover your system to the originally
installed factory state.
If you subsequently set up your hard disk drive again, do not change,
delete or add partitions in a manner other than specified in the manual,
otherwise you may find that space for the required software is not available.
In addition, if you use a third-party partitioning program to reconfigure the
partitions on your hard disk drive, you may find that it becomes impossible
to setup your computer.

1-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

When the sound mute feature has been activated by pressing the
FN + ESC key, be sure to disable this to allow sounds to be heard before
starting the restore process. Please refer to Chapter 5, The Keyboard, for
further details.

Be sure to connect the AC adaptor, otherwise you may run out of battery
during the recovery process.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Turn off the computer.

2. Turn on the computer and when the TOSHIBA screen appears
repeatedly press the F8 key.
3. The Advanced Boot Options menu will be displayed. Use the arrow
keys to select Repair Your Computer and press ENTER.
4. Select your preferred keyboard layout and press Next.
5. To access the recovery process please log on as an enabled user with
sufficent rights.
6. Click TOSHIBA HDD Recovery on the System Recovery Options
screen.
7. Follow the on-screen instructions on the TOSHIBA HDD Recovery
dialog.
The computer will be restored to its factory state.

User’s Manual 1-15

TECRA A10/S10/M10/SatellitePro S300

1-16 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 2

The Grand Tour

This chapter identifies the various components of the computer - it is

recommended that you become familiar with each before you operate the
computer.

Legal Footnote (Non-applicable Icons)*1

For more information regarding Non-applicable Icons, please refer to the
Legal Footnotes section in Appendix H or click the *1 above.

Please handle your computer carefully to avoid scratching or damaging the

surface.

Front with the display closed

The following figure shows the computer’s front with its display panel in the
closed position.
System indicators Headphone jack Microphone jack

Volume control dial Microphone

Figure 2-1 Front of the computer with display panel closed

System indicators These LED indicators allow you to monitor the

status of various computer functions and are
described in more detail within the System
indicators section.

User’s Manual 2-1

TECRA A10/S10/M10/SatellitePro S300

Volume control dial Use this dial to adjust the volume of the internal
stereo speaker and optional external stereo
headphones (if connected).
Move the Volume control dial to the right to
increase the volume and to the left to decrease
the volume.
Headphone jack A 3.5 mm mini headphone jack enables
connection of stereo headphones.

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer
to the Sound System section in Chapter 4,
Operating Basics for more information.

Left side
The following figure shows the computer’s left side.

Serial port Wireless communication PC Card eject PC Card slot

switch button

Cooling vents eSATA/USB Bridge media slot i.LINK (IEEE1394)

combo port port

Figure 2-2 The left side of the computer

Serial port Use this 9-pin port to connect serial devices such
as an external modem, serial mouse or serial
printer.
Some models are equipped with a serial port.
Cooling vents The cooling vents help keep the processor from
overheating.

2-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Do not block the cooling vents. Keep foreign metal objects, such as
screws, staples and paper clips, out of the cooling vents. Foreign metal
objects can create a short circuit, which can cause damage and fire,
possibly resulting in serious injury.

Wireless Slide this switch to the right to turn off Wireless

communication LAN, Bluetooth™ and Wireless WAN functions.
switch Slide it to the left to turn on the functions.
Only some models are equipped with Bluetooth,
Wireless LAN and Wireless WAN functions.

■ Do not use the Wireless LAN (Wi-Fi®) or Bluetooth functionalities near

a microwave oven or in areas subject to radio interference or magnetic
fields. Interference from a microwave oven or other source can disrupt
Wi-Fi or Bluetooth operation.
■ Turn all wireless functionalities off when near a person who may have a
cardiac pacemaker implant or other medical electric device. Radio
waves may affect pacemaker or medical device operation, possibly
resulting in serious injury. Follow the instruction of your medical device
when using any wireless functionality.
■ Always turn off wireless functionality if the computer is near automatic
control equipment or appliances such as automatic doors or fire
detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.

eSATA/USB One eSATA/USB combo port, which complies to

combo port the USB 2.0 standard, is provided on the left side
of the computer. The ports with the icon ( )
has USB Sleep and Charge. This port has
eSATA (External Serial ATA) function.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the eSATA/USB combo port. Foreign metal objects can create a short
circuit, which can cause damage and fire, possibly resulting in serious
injury.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Bridge media slot This slot lets you insert an SD™/SDHC™

memory card, miniSD™/microSD™ Card,
Memory Stick® (PRO™/PRO Duo™), xD-Picture
Card™ and MultiMediaCard™. Refer to the
Optional devices section in Chapter 3, Hardware,
Utilities and Options.

User’s Manual 2-3

TECRA A10/S10/M10/SatellitePro S300

Keep foreign metal objects, such as screws, staples and paper clips, out of
the Bridge media slot. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

PC Card slot This slot can accommodate a single Type II,

16-bit or 32-bit (CardBus) PC Card device.
Some models are equipped with a PC Card slot.
PC Card eject button This button is used in order to remove a PC Card
from within the computer.
Some models are equipped with a PC Card eject
button.

Keep foreign metal objects, such as screws, staples and paper clips,
out of the PC Card slot. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

i.LINK (IEEE1394) This port allows you to connect an external

port device, such as a digital video camera for
high-speed data transfer.
Some models are equipped with a i.LINK
(IEEE1394) port.

Right side
The following figure shows the computer’s right side.
Smart Card slot Modem jack

Optical disc drive Security lock slot

Universal Serial Bus
(USB 2.0) ports
Figure 2-3 The right side of the computer

Smart Card slot This slot can accommodate a single Smart Card
device. Some models are equipped with a Smart
Card slot.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the Smart Card slot. Foreign metal objects can create a short circuit, which
can cause damage and fire, possibly resulting in serious injury.

2-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Optical disc drive The computer is configured with a DVD-ROM,

DVD-ROM & CD-R/RW or DVD Super Multi
drive.
Universal Serial Bus Three Universal Serial Bus ports, which comply
(USB 2.0) ports to the USB 2.0 standard, are provided on the
right side of the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the USB connectors. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Modem jack The modem jack lets you use a modular cable to
connect the modem directly to a telephone line.
Some models are equipped with a modem jack.

■ Connection to any communication line other than an analog phone line

could cause a PC system failure.
■ Connect the built-in modem only to ordinary analog phone lines.
■ Never connect the built-in modem to a digital line (ISDN).
■ Never connect the built-in modem to the digital connector on a
public telephone or to a digital private branch exchange (PBX).
■ Never connect the built-in modem to a key telephone system for
residences or offices.
■ Avoid using your computer modem with the telephone cable connected
during an electrical storm. There may be a remote risk of electric shock
from lightning.

Security lock slot A security cable can be attached to this slot and
then connected to a desk or other large object in
order to deter theft of the computer.

User’s Manual 2-5

TECRA A10/S10/M10/SatellitePro S300

Back
The following figure shows the computer’s back.
LAN active indicator (orange) DC IN 15V jack
Link indicator (green)

External monitor port

LAN jack
Figure 2-4 The back of the computer

LAN jack This jack lets you connect to a LAN. The adaptor
has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T), Fast Ethernet
LAN (100 megabits per second, 100BASE-TX)
and Gigabit Ethernet LAN (1000 megabits per
second, 1000BASE-T). Refer to Chapter 4,
Operating Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack.
It could cause damage or malfunction.
■ Do not connect the LAN cable to a power supply. It could cause
damage or malfunction.

Link indicator This indicator glows green when the computer is

(green) connected to a LAN and the LAN is functioning
properly.
LAN active This indicator glows orange when data is being
indicator (orange) exchanged between the computer and the LAN.
External monitor This port provides 15-pin, analog VGA port.
port This port allows you to connect an external
monitor to the computer.
DC IN 15V jack The AC adaptor connects to this jack in order to
power the computer and charge its internal
batteries. Please note that you should only use
the model of AC adaptor supplied with the
computer at the time of purchase - using the
wrong AC adaptor can cause damage to the
computer.

2-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Underside
The following figure shows the underside of the computer. You should
ensure that the display is closed before the computer is turned over to
avoid causing any damage.
Notch Docking port Battery release latch
Battery lock Battery pack

Notch

Memory module slot

Figure 2-5 The underside of the computer

Notches Notches on the computer engage hooks on the

TOSHIBA Express Port Replicator to ensure a
secure connection.
Docking port This port enables connection of an optional
TOSHIBA Express Port Replicator described in
Chapter 3, Hardware, Utilities and Options.
Some models are equipped with a Docking port.

■ Only the TOSHIBA Express Port Replicator can be used with this
computer. Do not attempt to use any other Port Replicator.
■ Keep foreign objects out of the docking port. A pin or similar object can
damage the computer’s circuitry.
■ Do not use the computer’s External monitor port, when connecting the
TOSHIBA Express Port Replicator to the computer.

User’s Manual 2-7

TECRA A10/S10/M10/SatellitePro S300

Memory module slot The memory module slot allows for the
installation, replacement and removal of
additional memory module.
Refer to the Additional memory module section in
Chapter 3, Hardware, Utilities and Options.
Battery release latch Slide and hold this latch into its “Unlock” position
in order to release the battery pack for removal.
For more detailed information on removing the
battery pack please refer to Chapter 6, Power
and Power-Up Modes.
Battery pack The battery pack provides power to the computer
when the AC adaptor is not connected. For more
detailed information on the use and operation of
the battery pack please refer to Chapter 6, Power
and Power-Up Modes.
Battery lock Slide the battery lock to release the battery pack
ready for removal.

2-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Front with the display open

This section shows the computer with the display panel open. In order to
open the display, lift the display panel up and position it at a comfortable
viewing angle for you.
Wireless LAN antenna (Not shown)
Wireless WAN antennas (Not shown)

Wireless LAN antenna

(Not shown)
Web Camera

Web Camera LED

Display screen
Display hinge
Stereo speaker (Right)
LCD Sensor switch
(Not shown) AccuPoint
AccuPoint control buttons

Fingerprint Sensor
Display hinge

Stereo speaker (Left)

Power button Bluetooth antenna

(Not shown)
TOSHIBA Assist button
Touch Pad control buttons
TOSHIBA Presentation button
Keyboard Touch Pad

Figure 2-6 The front of the computer with the display panel open

Display hinges The display hinges allow the display panel to be

position at a variety of easy-to-view angles.
Display screen Please be aware that, when the computer is
operating on the AC adaptor, the image
displayed on the internal screen will be
somewhat brighter than when it operates on
battery power. This difference in brightness
levels is intended to save power when
operating on batteries. For more information on
the computer’s display, please refer to the
Display Controller and Video mode section in
Appendix B.
Web Camera LED The Web Camera LED glows when the Web
Camera is operating.
Some models are equipped with a
Web Camera LED.

User’s Manual 2-9

TECRA A10/S10/M10/SatellitePro S300

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. Camera
Assistant Software will help you to add various
video effects to your video or photograph.
Enables the transmission of video and use of
video chat via the internet using specialized
applications.
The effective pixel count for this web camera is
1.31 million (maximum photograph size:
1280x1024 pixels).
Some models are equipped with a Web Camera.
Please refer to the Web Camera section in
Chapter 4, Operating Basics.
Touch Pad The Touch Pad located in the center of the palm
rest is used to control the movement of the on-
screen pointer. For more information, please
refer to the Using the Touch Pad section in
Chapter 4, Operating Basics.
Touch Pad control The control buttons located below the Touch Pad
buttons allow you to select menu items or manipulate text
and graphics as designated by the on-screen
pointer.
AccuPoint A pointer control device located in the center of
the keyboard is used to control the on-screen
pointer. Refer to the Using the AccuPoint section
in Chapter 4, Operating Basics.
Some models are equipped with a AccuPoint.
AccuPoint control Control buttons below the keyboard let you select
buttons menu items or manipulate text and graphics
designated by the on-screen pointer. Refer to the
Using the AccuPoint section in Chapter 4,
Operating Basics.
Some models are equipped with a AccuPoint
control buttons.
Keyboard The internal keyboard provides the embedded
numeric overlay keys, dedicated cursor control
overlay keys, and and Keys. The
keyboard is compatible with the IBM® enhanced
keyboard. Refer to Chapter 5, The Keyboard, for
details.

2-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.
Power button Press this button to turn the computer’s power on
and off.

TOSHIBA Assist Press this button to launch the program

button automatically. When power-off, Sleep Mode and
Hibernation Mode, press this button to start the
computer and launch the program.
Some models are equipped with a TOSHIBA
Assist button.
TOSHIBA The TOSHIBA Presentation button has the same
Presentation button functionality as the Connect display button in the
Mobility Center. Pressing this button when an
external display is connected will open the
Windows Vista TMM (Transient Multimon
Manager) screen.
Some models are equipped with a TOSHIBA
Presentation button.
Fingerprint Sensor This sensor enables you to enroll and recognize
a fingerprint.
For detailed information on Fingerprint Sensor,
refer to Chapter 4, Using the Fingerprint Sensor.
Some models are equipped with a Fingerprint
Sensor.
LCD Sensor switch This switch senses when the display panel is
either closed or opened and activates the Panel
Power Off/On feature as appropriate. For
example, when you close the display panel the
computer enters Hibernation Mode and shuts
itself down and then, when you next open the
display, the computer will automatically start up
and return you to the application you were
previously working on.
You can specify within the Power Options. To
access it, click Start -> Control Panel -> System
and Maintenance -> Power Options.

Do not put any magnetic objects close to this switch as they may cause the
computer to automatically enter Hibernation Mode and shut down even if
the Panel Power Off feature is disabled.

User’s Manual 2-11

TECRA A10/S10/M10/SatellitePro S300

Bluetooth antenna Some computers in this series are equipped with

a Bluetooth antenna.
Wireless LAN Some computers in this series are equipped with
antennas the Wireless LAN antennas.
Wireless WAN Some computers in this series are equipped with
antennas the Wireless WAN antennas.

Indicators
This section explains indicator functions.

System indicators
LED system indicators next to their respective icons, glow when specific
computer operations are in progress.

Figure 2-7 System indicators

DC IN The DC IN indicator normally glows green when

power is being correctly supplied from the AC
power adaptor. However, If the output voltage
from the adaptor is abnormal, or if the computer’s
power supply malfunctions, this indicator will
flash orange.
Power The Power indicator normally glows green when
the computer is turned on. However, if you turn
the computer off into Sleep Mode, this indicator
will flash orange - approximately one second on,
two seconds off - both while the system is
shutting down and while it remains turned off.
Battery The Battery indicator shows the condition of the
battery’s charge - green indicates the battery is
fully charged, orange indicates the battery is
charging, and flashing orange indicates a low
battery condition. Please refer to Chapter 6,
Power and Power-Up Modes for more
information on this feature.
Hard Disk Drive/ The Hard Disk Drive/Optical Disc Drive
Optical Disc Drive indicator glows green whenever the computer is
accessing the built-in hard disk drive, optical disc
drive or eSATA device.

2-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Bridge media slot The Bridge media slot indicator glows green
when the computer is accessing the Bridge
media slot.

Wireless The Wireless communication indicator blinks

communication orange when the Bluetooth and Wireless LAN
functions are turned on.
Only some models are equipped with Bluetooth
and Wireless LAN functions.
Wireless WAN The Wireless WAN indicator glows or blinks blue
when the Wireless WAN function is on.
The indicator will glow or blink in order to indicate
the connection status of the Wireless WAN
function.
A Wireless WAN module must be installed to use
this function. Some models are equipped with a
Wireless WAN module.

Keyboard indicators
The following figures show the positions of the CAPS LOCK indicator and
the keypad overlay indicators which show the following conditions:
■ When the CAPS LOCK indicator glows, the keyboard will produce
capitals when any letter is typed.
■ When the Arrow Mode indicator glows, the keypad overlay allows you to
use cursor functions.
■ When the Numeric Mode indicator glows, the keypad overlay allows
you to enter numbers.

CAPS LOCK indicator

Figure 2-8 CAPS LOCK indicator

CAPS LOCK This indicator glows green when letter keys are
locked into their uppercase format.

User’s Manual 2-13

TECRA A10/S10/M10/SatellitePro S300

Arrow mode Numeric mode

indicator indicator

Figure 2-9 Keypad overlay indicators

Arrow mode When the Arrow mode indicator lights green,

you can use the gray labeled keys on the keypad
overlay as cursor keys. Please refer to the
Keypad overlay section in Chapter 5, The
Keyboard for more information.
Numeric mode When the Numeric mode indicator lights green,
you can use the gray labeled keys on the keypad
overlay for number entry. Please refer to the
Keypad overlay section in Chapter 5, The
Keyboard for more information.

Optical disc drives

The computer is installed with a DVD-ROM, DVD-ROM & CD-R/RW or
DVD Super Multi drive. A Serial ATA interface controller is used for
CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an
indicator on the drive glows.
For information on loading and unloading discs refer to the Using optical
disc drives section in Chapter 4, Operating Basics.

Region codes for DVD drives and media

DVD Super Multi drives and their associated media are manufactured
according to the specifications of six marketing regions. When you
purchase DVD-Video, make sure it matches your drive, otherwise it will not
play properly.

Code Region
1 Canada, United States
2 Japan, Europe, South Africa, Middle East
3 Southeast Asia, East Asia
4 Australia, New Zealand, Pacific Islands, Central America,
South America, Caribbean
5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia
6 China

2-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Writable discs
This section describes the types of writable CD/DVD discs. Check the
specifications of your drive to see the types of discs it can write. Use
TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4,
Operating Basics.

CDs
■ CD-R discs can be written only once. The recorded data cannot be
erased or changed.
■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW
discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs
■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs
can be written only once. The recorded data cannot be erased or
changed.
■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than
once.

Formats
The drives support the following formats.

DVD-ROM drive
The drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA,
CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1, Mode 2,
CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA) and
Addressing Method 2.

DVD-ROM & CD-R/RW drive

The drive supports the formats in addition to the DVD-ROM drive,
and CD-R, CD-RW.

DVD Super Multi drive Double Layer

The drive supports the formats in addition to the DVD-ROM&CD-R/RW
drive, and DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL
(Format1), DVD+R DL.

Some types and formats of DVD-R DL and DVD+R DL discs may be

unreadable.

User’s Manual 2-15

TECRA A10/S10/M10/SatellitePro S300

DVD-ROM drive
The full-size DVD-ROM drive module lets you run either 12 cm (4.72") or
8 cm (3.15") CD/DVDs without using an adaptor.
The read speed is slower at the center of a disc and faster at the outer
edge.
DVD read 8 speed (maximum)
CD read 24 speed (maximum)

DVD-ROM & CD-R/RW drive

The full-size DVD-ROM & CD-R/RW drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.
The read speed is slower at the center of a disc and faster at the outer
edge.
DVD read 8 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, Ultra-speed media)

DVD Super Multi drive Double Layer

The full-size DVD Super Multi drive module lets you record data to
rewritable CD/DVDs as well as run either 12 cm (4.72") or
8cm (3.15") CD/DVDs without using an adaptor.
The read speed is slower at the center of a disc and faster at the outer
edge.
DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-R DL write 6 speed (maximum)
DVD-RW write 6 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+R DL write 6 speed (maximum)
DVD+RW write 8 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, Ultra-speed media)

2-16 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

AC adaptor
The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volts and to a frequency of either 50 or 60 hertz, enabling you to use
this computer in almost all country/region. The adaptor converts AC power
to DC power and reduces the voltage supplied to this computer.
To recharge the battery, simply connect the AC adaptor to a power source
and to the computer. Please refer to Chapter 6, Power and Power-Up
Modes for further information.

Figure 2-10 The AC adaptor (2-pin plug)

Figure 2-11 The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin adaptor/

power lead will be bundled with the computer.
■ Do not use a 3-pin to 2-pin conversion plug.
■ The supplied power cord conforms to safety rules and regulations in
the region the product is bought and should not be used outside of this
region. In order to use the adaptor/computer in other regions, you
should please buy a power cord that conforms to the safety rules and
regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your
computer, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the computer. Use of an incompatible AC adaptor
could cause fire or damage to the computer possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of an
incompatible adaptor.

User’s Manual 2-17

TECRA A10/S10/M10/SatellitePro S300

2-18 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 3

Hardware, Utilities and Options

Hardware
This section describes the hardware of your computer.
The actual specifications may vary depending on the model you
purchased.

Processor

CPU The computer is equipped with one of the

following Intel® processors.
■ Intel® Core™ 2 Duo Processor, which
incorporates a 3MB level2 cache memory
and also supports Enhanced Intel
SpeedStep® Technology.
■ Intel® Core™ 2 Duo Processor, which
incorporates a 6MB level2 cache memory
and also supports Enhanced Intel
SpeedStep® Technology.

Some models in this series use Intel® Centrino® 2 processor technology

which is based on three separate components, the Intel® Core™ 2 Duo
processor, Intel® Wi-Fi Link 5300AGN -OR- 5100AGN and the Intel® GM/
PM45 Express Chipset.

Legal Footnote (CPU)*2

For more information on the CPU, please refer to the Legal Footnotes
section in Appendix H or Click the *2 above.

User’s Manual 3-1

TECRA A10/S10/M10/SatellitePro S300

Memory

Memory slots 512, 1,024, 2,048 or 4,096MB memory modules

can be installed in the computer’s two memory
slots for a maximum of 8,192MB system memory.
This computer can be equipped with memory
modules of a maximum size of 8,192MB. The
actual amount of useable system memory will be
less than the installed memory modules.
Video RAM The memory in a computer’s graphics adaptor,
used to store the image displayed on a bitmap
display.
The amount of Video RAM available is
dependent on the computer’s system memory.
Start -> Control Panel -> Appearance and
Personalization -> Personalization -> Display
Settings.
The amount of Video RAM can be verified by
clicking the Advanced Settings... button in the
Display Settings window.

If your computer is configured with two 2 GB memory modules or more, the

memory might be displayed as approximately 3 GB only (depending on the
computer’s hardware specifications).
This is correct because the operating system usually displays the available
memory instead of the physical memory (RAM) built into the computer.
Various system components (like the video adapter’s GPU and PCI
devices like Wireless LAN, etc.) require their own memory space. Since a
32-bit operating system cannot address more than 4 GB of memory these
system resources overlap the physical memory. It is a technical limitation
that the overlapped memory is not available to the operating system.
Even though some tools might display the actual physical memory built
into your computer, the memory available to the operating system will still
be approximately 3 GB only.

Legal Footnote (Memory (Main System))*3

For more information regarding Memory (Main System), please refer to the
Legal Footnotes section in Appendix H or click the *3 above.

Power
Battery pack The computer is powered by one rechargeable
lithium-ion battery pack.

3-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Legal Footnote (Battery Life)*4

For more information regarding Battery Life, please refer to the Legal
Footnotes section in Appendix H or click the *4 above.

RTC battery The internal RTC battery backs up the Real Time
Clock (RTC) and calendar.
AC adaptor The AC adaptor provides power to the system
and recharges the batteries when they are low. It
comes with a detachable power cord which will
either have a 2-pin or 3-pin plug enclosure.
As the AC adaptor is universal, it can receive a
range of AC voltages from 100 to 240 volts,
however you should note that the output current
varies among different models. Using the wrong
adaptor can damage your computer. Refer to the
AC adaptor section in Chapter 2, The Grand
Tour.

Disks
Hard disk drive or This computer is equipped with one of the
Solid state drive following hard disk drive (HDD) or solid state
drive (SSD) types. The capacity of each HDD or
SSD model is different.
■ HDD
■ 120GB
■ 160GB
■ 200GB
■ 250GB
■ SSD
■ 64GB
■ 128GB
Please note that part of the hard disk or solid
state drive’s overall capacity is reserved as
administration space.

■ In this manual, the word “HDD” or “Hard disk drive” also refers to the
SSD unless otherwise stated.
■ SSD is a large-capacity storage media which uses Solid-State Memory
in place of a magnetic disk of the hard disk.

Under certain unusual conditions of prolonged non-use and/or exposure to

high temperatures, the SSD may be vulnerable to data retention errors.

User’s Manual 3-3

TECRA A10/S10/M10/SatellitePro S300

Legal Footnote (Hard Disk Drive (HDD) Capacity)*5

For more information regarding Hard Disk Drive (HDD) Capacity, please
refer to the Legal Footnotes section in Appendix H or click the *5 above.

Optical disc drive

Drive The following optical disc drive is pre-installed in

this computer.
■ DVD-ROM drive
■ DVD-ROM&CD-R/RW drive
■ DVD Super Multi drive Double Layer

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

Display
The computer’s internal display panel supports high-resolution video
graphics and can be set to a wide range of viewing angles for maximum
comfort and readability.

Display panel ■ TECRA A10/S10 Satellite Pro S300

15.4” TFT LCD screen, 16 million colors, with
one of the following resolutions:
■ WXGA, 1280 horizontal x
800 vertical pixels
■ WSXGA+, 1680 horizontal x
1050 vertical pixels
■ TECRA M10
14.1” TFT LCD screen, 16 million colors, with
one of the following resolutions:
■ WXGA, 1280 horizontal x
800 vertical pixels
■ WXGA+, 1440 horizontal x
900 vertical pixels

Legal Footnote (LCD)*6

For more information regarding the LCD, please refer to the Legal
Footnotes section in Appendix H or click the *6 above.

Graphics controller The graphics controller maximizes display

performance. Refer to Display Controller and
Video mode section in Appendix B for more
information.

3-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Legal Footnote (Graphics Processor Unit (“GPU”))*7

For more information regarding the Graphics Processor Unit (“GPU”),
please refer to the Legal Footnotes section in Appendix H or click the *7
above.

Sound

Sound system The integrated sound system provides support

for the computer’s internal speakers and
microphone, as allowing an external microphone
and headphones to be connected via the
appropriate jacks.

Multimedia
Web Camera Web Camera is a device that allows you to
record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. Camera
Assistant Software will help you to add various
video effects to your video or photograph.
Please refer to the Web Camera section in
Chapter 4, Operating Basics.

Communications
Modem Provides capability for data and fax
communication. It supports V.90 (V.92).
The speed of data transfer and fax
communication depends on the analog
telephone line conditions. The computer has a
modem jack for connection to a telephone line.
Both V.90 and V.92 are supported only in the
USA, Canada, UK, France and Germany.
V.90 is available in other regions.
Some models are equipped with the integrated
modem.
LAN The computer has built-in support for Ethernet
LAN (10 megabits per second, 10BASE-T),
Fast Ethernet LAN (100 megabits per second,
100BASE-TX) and Gigabit Ethernet LAN
(1000 megabits per second, 1000BASE-T).

User’s Manual 3-5

TECRA A10/S10/M10/SatellitePro S300

Bluetooth Some computers in this series have Bluetooth

wireless communication function which
eliminates the need for cables between
electronic devices such as computers, printers
and mobile phones. When it is enabled,
Bluetooth provides the wireless personal area
network environment which is safe and
trustworthy, that is quick and easy.
Wireless LAN Some computers in this series are equipped with
a Wireless LAN module that is compatible with
other LAN systems based on Direct Sequence
Spread Spectrum/Orthogonal Frequency Division
Multiplexing radio technology that complies with
the IEEE 802.11 Standard.

Legal Footnote (Wireless LAN)*8

For more information regarding Wireless LAN, please refer to the Legal
Footnotes section in Appendix H or click the *8 above.

Special features
The following features are either unique to TOSHIBA computers or are
advanced features which make the computer more convenient to use.
Access each function using the following procedures.
*1 To access the Power Options, click Start -> Control Panel ->
System and Maintenance -> Power Options.
TOSHIBA Assist Press this button to launch the program
button automatically. When power-off, Sleep Mode and
Hibernation Mode, press this button to start the
computer and launch the program.
Some models are equipped with a TOSHIBA
Assist button.
TOSHIBA The TOSHIBA Presentation button has the same
Presentation functionality as the Connect display button in the
button Mobility Center. Pressing this button when an
external display is connected will open the
Windows Vista TMM (Transient Multimon
Manager) screen.
Some models are equipped with a TOSHIBA
Presentation button.
Hot keys Hot keys are specific key combinations that let
you quickly change the system configuration
directly from the keyboard without running a
system program.

3-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Display automatic This feature automatically cuts off power to the

power off *1 computer’s display panel when there is no
keyboard input for a specified time, with power
being restored the next time a key is pressed.
This can be specified in the Power Options.
HDD automatic This feature automatically cuts off power to the
power off *1 hard disk drive when it is not accessed for a
specified time, with power being restored when
the hard disk drive is next accessed. This can be
specified in the Power Options.
System automatic This feature automatically shuts down the system
Sleep/Hibernation into either Sleep Mode or Hibernation Mode when
Mode *1 there is no input or hardware access for a
specified time. This can be specified in the Power
Options.
Keypad overlay A ten-key numeric keypad is integrated into the
keyboard. Please refer to the Keypad overlay
section in Chapter 5, The Keyboard, for
information on using this feature.
Power on password Two levels of password security, supervisor and
user, are available to prevent unauthorized
access to your computer.
Instant security A specific hot key function automatically locks the
system providing data security.
Intelligent power A microprocessor in the computer’s intelligent
supply *1 power supply detects the battery’s charge,
automatically calculates the remaining battery
capacity and protects electronic components
from abnormal conditions such as a voltage
overload from the AC adaptor. This can be
specified in the Power Options.
Battery save mode *1 This feature lets you configure the computer in
order to save battery power. This can be
specified in the Power Options.
Panel power on/off *1 This feature automatically turns power to the
computer off when the display panel is closed,
and turns it back on when the display panel is
opened. This can be specified in the Power
Options.
Low battery When battery power is exhausted to the point that
automatic computer operation cannot be continued, the
Hibernation Mode *1 system automatically enters Hibernation Mode
and shuts itself down. This can be specified in the
Power Options.

User’s Manual 3-7

TECRA A10/S10/M10/SatellitePro S300

Heat dispersal *1 To protect against overheating, the processor has

an internal temperature sensor so that, if the
computer’s internal temperature rises to a certain
level, the cooling fan is turned on or the
processing speed is lowered. This can be
specified in the Power Options.
TOSHIBA HDD This feature uses the acceleration sensor built in
Protection the computer to detect vibration and shocks,
and automatically moves the hard disk drive’s
read/write head to a safe position in order to
reduce the risk of damage that could be caused
by head-to-disk contact. Refer to the Using the
Hard Disk Drive (HDD) Protection section in
Chapter 4, Operating Basics, for more details.

■ The TOSHIBA HDD Protection function does not guarantee that the
hard disk drive will not be damaged.
■ TOSHIBA HDD Protection cannot be used in models that are equipped
with SSD.

Hibernation Mode This feature lets you turn off the power to the
computer without exiting from your software.
The contents of main memory are automatically
saved to the hard disk drive so that when you
next turn the power on again, you can continue
working right where you left off. Refer to the
Turning off the power section in Chapter 1,
Getting Started, for more details.
Sleep Mode If you have to interrupt your work, you can use
this feature to allow you to turn off power to the
computer without exiting from your software.
Data is maintained in the computer’s main
memory so that when you next turn on the power,
you can continue working right where you left off.
USB Sleep and This feature allows you to charge USB-
Charge function compatible external devices such as mobile
phones or portable digital music players via the
USB port when your computer is in Sleep Mode,
Hibernation Mode or in the shutdown state.
This function is worked by the USB Sleep and
Charge Utility. For more information, please refer
to the Using the TOSHIBA USB Sleep and
Charge Utility section in Chapter 4, Operating
Basics.

3-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

USB Wakeup This function restores the computer from

function Sleep Mode depending on the external devices
connected to the USB ports.
For example, if a mouse or USB keyboard is
connected to a USB port, moving the
mouse/keyboard will wakeup the computer.
The “USB Wakeup function” operates under
Windows Vista operating system and it works for
all USB ports.
TOSHIBA PC Health The TOSHIBA PC Health Monitor software
Monitor program monitors computer system functions
such as power consumption, the cooling system
and HDD Drop sensor. It alerts users of specific
system conditions via pop-up messages. It also
tracks the usage of the computer and related
devices, logging the service relevant information
on the computer’s hard disk drive.
Refer to Appendix G, TOSHIBA PC Health
Monitor.

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on
the computer.
TOSHIBA Power TOSHIBA Power Saver provides you with the
Saver features of more various power supply
managements.
TOSHIBA Button This utility controls the following computer button
Support functions.
■ TOSHIBA Assist
■ TOSHIBA Presentation
The starting application from the button can be
changed.

TOSHIBA Button Support cannot be used in models that are not equipped
with TOSHIBA Assist button and TOSHIBA Presentation button.

TOSHIBA Zooming This utility allows you to enlarge or reduce the

Utility icon size on the Windows Desktop, or the zoom
factor associated with specific supported
applications.

User’s Manual 3-9

TECRA A10/S10/M10/SatellitePro S300

TOSHIBA PC The TOSHIBA PC Diagnostic Tool will display

Diagnostic Tool basic system configuration information and allow
the functionality of some of the computer’s built-
in hardware devices to be tested.
TOSHIBA Password The TOSHIBA Password utility allows you to set
Utility a password in order to restrict access to the
computer.
TOSHIBA Flash The TOSHIBA Flash Cards provide a quick way
Cards to modify selected system functions and to
launch applications.
■ Hot key function
■ TOSHIBA utility launcher function
HW Setup This utility allows you to customize your
hardware settings according to the way you work
with the computer and the peripherals you use.
TOSHIBA The TOSHIBA Accessibility utility provides
Accessibility support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
use, the utility allows you to make the FN key
“sticky”, that is you can press it once, release it,
and they press one of the “Function” keys in
order to access its specific function. When set,
the FN key will remain active until another key is
pressed.

3-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Utilities and Applications

This section describes the pre-installed utilities that come with the
computer and details how to start them. For further information on their
operation, please refer to each utility’s online manual, help files or
README.TXT file.
* Indicates software that is preinstalled with some models

Fingerprint Utility This product has a fingerprint utility installed for

the purpose of enrolling and recognizing
fingerprints which can then be linked to a
username and password in order to remove the
need to input these details from the keyboard.
Just by swiping an enrolled finger against the
fingerprint sensor, the following functions will be
enabled:
■ Logon to Windows and access a security
enabled homepage through Internet Explorer.
■ Files and folders can be encrypted/decrypted
and third party access to them is prevented.
■ Disable the password-protected screen-saver
when returning from a power-saving mode
such as Sleep Mode.
■ Authentication of the User Password (and,
if applicable, the HDD(Hard Disk Drive)
Password) when booting up the computer
(Power-on Security).
■ Single Sign-on feature

Fingerprint security cannot be used in models that do not have a fingerprint

module installed.

TOSHIBA Face TOSHIBA Face Recognition uses a face

Recognition* verification library to verify the face data of users
when they log in to Windows. If the verification is
successful, the user will be logged into Windows
automatically. The user can thus avoid having to
enter a password or the like, which makes the
login process easier.
TOSHIBA DVD This software is provided for playback of DVD
Player Video.
It has an on-screen interface and functions.
Click Start -> All Programs -> TOSHIBA DVD
PLAYER -> TOSHIBA DVD PLAYER.
For details on how to use TOSHIBA DVD
PLAYER, see the help file.

User’s Manual 3-11

TECRA A10/S10/M10/SatellitePro S300

■ Frame dropping, audio skipping or out of synch audio and video may
occur during playback of some DVD Video titles.
■ Make sure to connect the computer’s AC adaptor when playing a DVD
Video. Power-saving features may interfere with smooth playback.

Bluetooth Stack for This software enables communication between

Windows by Toshiba the computer and external Bluetooth devices
such as printers and mobile phones.

Bluetooth functions cannot be used in models that do not have a Bluetooth

module installed.

TOSHIBA SD The TOSHIBA SD Memory Boot Utility allows

Memory Boot Utility you to create a bootable SD memory card to start
the system. You can boot TOSHIBA SD Memory
Boot Utility from the menu bar as follows. Click
Start -> All Programs -> TOSHIBA -> Utilities
-> SD Memory Boot Utility.

SD Memory Card Format Utility and other SD functions are packaged into
TOSHIBA SD Memory Utilities.

TOSHIBA SD This utility allows you to format an SD/SDHC

Memory Card memory card by the SD standard format.
Format
TOSHIBA Assist TOSHIBA Assist is a graphical user interface that
provides access to specific tools, utilities and
applications that make the use and configuration
of the computer easier.
TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that
improve the ease and control of communication
devices and network connections, help in the
identification of communication problems and
allow the creation of profiles if you need to switch
between different locations and communication
networks. To access this utility, click Start ->
All Programs -> TOSHIBA -> ConfigFree.

3-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

TOSHIBA Disc You can create CD’s and DVD’s in a number of

Creator formats including audio CD’s that can be played
on a standard CD player, and data CD’s/DVD’s
which can store copies of the files and folders on
your computer’s hard disk drive. This software
can be used on models with a DVD Super Multi
drive.
To start this utility, click Start -> All Programs ->
TOSHIBA -> CD&DVD Applications -> Disc
Creator.
CD/DVD Drive This utility allows you to configure the read speed
Acoustic Silencer of the optical disc drive. You can either configure
Normal Mode, which operates the drive at its
maximum speed for quick data access, or Quiet
Mode which runs audio CDs at single speed and
which can lessen operational noise.
It is ineffective with DVDs.
Display Rotation This utility allows you to quickly rotate the
Settings Windows Desktop by either 0 degrees and
180 degrees. In use you are able to perform a
rotation function by pressing either CTRL + ALT
+ Up Arrow ( ) to rotate 0 degrees or CTRL
+ ALT + Down Arrow ( ) to rotate
180 degrees - in a multi-monitor setup, the
display that contains the cursor will be affected
by these changes.
Windows Mobility Mobility Center is a utility for accessing several
Center mobile PC settings quickly in one window.
A default maximum of eight tiles are provided by
the operating system, and the additional two tiles
are added to your Mobility Center.
■ Lock Computer:
This can be used to lock your computer
without turning it off. This has the same
function as the Lock button at the bottom of
the right pane in the start menu.
■ TOSHIBA Assist:
This can be used to open TOSHIBA Assist if
it is already installed in your computer.

User’s Manual 3-13

TECRA A10/S10/M10/SatellitePro S300

TOSHIBA USB Sleep This utility is able to either enable or disable the
and Charge Utility USB Sleep and Charge function.
Shows the positions of USB ports that support
the USB Sleep and Charge function and displays
the battery’s remaining capacity.
To start this utility, click Start -> All Programs ->
TOSHIBA -> Utilities -> USB Sleep and
Charge.
Trusted Platform The TPM (Trusted Platform Module) is a security
Module (TPM) encryption device for the hard disk drive.
BIOS setup and Infineon TPMSoftware
Professional Package must be configured in
order to use TPM.
For further information on how to set up and use
this utility, please refer to the Infineon TPM
Installation Guide.

To enable TPM through the BIOS setup:

1. Turn on the computer while pressing the ESC key.
2. Press the F1 key when directed.
3. Press the PGDN key.
4. Press the down arrow key until TPM is highlighted, then press the
space bar to change the TPM status to Enabled.
5. Press the Y key to save the changes.
6. Press END and then press the Y key to accept the changes.
The computer will restart.
In order to change the TPM setting when the Hide TPM setting is currently
set to Yes, switch the Hide TPM setting from Yes to No.

3-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Optional devices
Optional devices can expand the computer’s capabilities and its versatility.
This section describes the connection or installation of the following
devices:

Cards/memory
■ PC Card
■ Smart Card
■ Bridge media slot
■ Secure Digital™ (SD) Card (SD memory card, SDHC memory card,
miniSD Card, microSD Card)
■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick
PRO Duo)
■ xD picture card
■ MultiMediaCard
■ Additional memory module

Peripheral devices
■ Hard disk drive pack
■ External monitor
■ USB FDD Kit
■ eSATA
■ i.LINK (IEEE1394)
■ Serial port
■ TOSHIBA Express Port Replicator

Other
■ Security lock

PC Card
The computer is equipped with a single PC Card slot that can
accommodate a Type II format card. Any PC Card that meets industry
standards, either manufactured by TOSHIBA or another vendor, can be
installed as the slot supports 16-bit PC Cards and 32-bit CardBus cards.
For reference, CardBus supports the newer standard of 32-bit PC Cards
and provides superior performance for the greater demands of applications
such as multimedia data transmission.
PC Cards can sometimes become hot during computer operation. Before
you remove a PC Card always wait for it to cool. You could get burned
removing a hot PC Card.

User’s Manual 3-15

TECRA A10/S10/M10/SatellitePro S300

Inserting a PC Card
The Windows hot-install feature allows you to insert PC Cards while the
computer is turned on.
Do not insert a PC Card while the computer is in Sleep Mode or
Hibernation Mode as you may find that some cards do not work properly.
To insert a PC Card, follow the steps as detailed below:
1. Insert the PC Card into the PC Card slot on the side of the computer.
2. Press the PC Card gently to ensure a firm connection is made.

PC Card slot

PC Card

Figure 3-1 Inserting the PC Card

3. After inserting the PC Card you should refer to its documentation and
also check the configuration in Windows in order to ensure that it is
correct.

Removing a PC Card
To remove a PC Card, follow the steps as detailed below:
1. Open the Safely Remove Hardware icon on the Windows Taskbar.
2. Point to PC Card and click the left Touch Pad control button.
3. Press the PC Card eject button to partially extend it out of the computer.
If the PC Card is not inserted all the way into the computer, the eject button
may not cause it to pop out sufficiently to allows it to be grasped. In this
instance, simply push the PC Card firmly back into the computer and then
press the eject button again.

4. Press the extended PC Card eject button in order to eject the PC Card
partially out of the computer.

3-16 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

5. Grasp the PC Card and remove it.

PC Card

PC Card eject button

Figure 3-2 Removing the PC Card

Smart Card
A Smart Card is a credit card sized plastic card. An extremely thin
integrated circuit (IC chip) is embedded into the card on which information
can be recorded. These cards can be used for a wide variety of
applications including telephone related and electronic monetary payments.
This section contains information on the proper use of the Smart Card slot,
and it is strongly recommended that you read it before operating the
computer.
Some models are equipped with a Smart Card slot.
■ Your computer supports ISO7816-3 asynchronous cards (support
protocols are T=0 and T=1) with a working voltage of 5V.
■ The computer is equipped with either a PC Card slot or a
Smart Card slot.

User’s Manual 3-17

TECRA A10/S10/M10/SatellitePro S300

Inserting a Smart Card

The Smart Card slot is located on the right side of the computer. The
Windows hot-install feature allows you to insert a Smart Card while the
computer is turned on.
To install a Smart Card, follow the steps as detailed below:
1. Insert the Smart Card into the Smart Card slot with the metal
connectors facing up.
2. Press the Smart Card gently to ensure a firm connection is made.
The computer will identify the Smart Card and display an icon in the
Windows Taskbar.
■ When inserting a Smart Card into the Smart Card slot, make sure to
confirm that the card is oriented correctly before inserting.
■ Insert the Smart Card until it reaches the end of the Smart Card slot.
There will be about 2cm of the Smart Card sticking out of the Smart
Card slot. Do not attempt to insert it further.
■ Always remove the Smart Card from the Smart Card slot before moving
the computer.
■ Remove the Smart Card after use.
Failure to follow these instructions may result in damage to the computer
and/or damage to the Smart Card.

Smart Card

Figure 3-3 Inserting a Smart Card

3. After inserting the Smart Card, you should refer to its documentation
and also check the configuration in Windows in order to ensure that it is
correct.

3-18 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Removing a Smart Card

To remove a Smart Card, follow the steps as detailed below:
1. Open the Safely Remove Hardware icon on the Windows Taskbar.
■ Before removing the Smart Card, confirm that the Smart Card is not
working with any program or system.
■ Be careful not to bend the Smart Card while removing it from the
computer.
2. Point to Smart Card and click the left Touch Pad control button.
3. Grasp the Smart Card and remove it.

Smart Card

Figure 3-4 Removing a Smart Card

Bridge media slot

The computer is equipped with a Bridge media slot that can accommodate
some kinds of memory media with various memory capacities so that you
can easily transfer data from devices, such as digital cameras and
Personal Digital Assistants.
■ Keep foreign objects out of the Bridge media slot. Never allow metal
objects, such as screws, staples and paper clips, to enter the computer
or Keyboard. Foreign metal objects can create a short circuit, which
can cause computer damage and fire, possibly resulting in serious
injury.
■ Memory Stick Duo is not compatible with the Bridge media slot. Do not
insert Memory Stick Duo into the slot or you may not be able to remove
it. Data may be lost or damaged if you use any memory media other
than those supported.

User’s Manual 3-19

TECRA A10/S10/M10/SatellitePro S300

■ This Bridge media slot supports the following memory media.

■ Secure Digital (SD) Card (SD memory card, SDHC memory card,
miniSD Card, microSD Card)
■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick
PRO Duo)
■ xD picture card
■ MultiMediaCard (MMC™)
■ Please note that an adaptor is required to use miniSD/microSD Card.
■ Please note that an adaptor is required to use Memory Stick PRO Duo.
■ Please note that not all memory media have been tested and verified to
work correctly. Therefore, it is not possible to guarantee that all
memory media will operate properly.
■ The slot does not support Magic Gate functions.

Secure Digital (SD) Card microSD card adaptor and microSD card

Memory Stick xD picture card MultiMediaCard (MMC)

Figure 3-5 Examples of memory media

Memory media
This section provides the important safety precautions in order to handle
your memory media.

Points to note about the SD/SDHC memory card

SD/SDHC memory cards comply with SDMI (Secure Digital Music
Initiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device, and you may not
reproduce any copyrighted material except for your personal enjoyment.
Below is a simple explanation for distinguishing SD memory cards from
SDHC memory cards.
■ SD and SDHC memory cards appear the same externally. However, the
logo on SD and SDHC memory cards is different, so pay careful
attention to the logo when purchasing.

■ The SD memory card logo is ( ).

■ The SDHC memory card logo is ( ).

3-20 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ The maximum capacity of SD memory cards is 2GB. The maximum

capacity of SDHC memory cards is 16GB.
Card Type Capacities
SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,
512MB, 1GB, 2GB
SDHC 4GB, 8GB, 16GB

Memory media format

New media cards are formatted according to specific standards. If you wish
to reformat a media card, be sure to do so with a device that uses media
cards.

Formatting an SD/SDHC memory card

SD/SDHC memory cards are sold already formatted in conformity to
specific standards. If you format the SD/SDHC memory card again, be sure
to format it with the TOSHIBA SD Memory Card Format utility, not with the
format command provided within Windows.
In order to run the TOSHIBA SD Memory Card Format utility, click Start ->
All Programs -> TOSHIBA -> Utilities -> SD Memory Card Format.
The TOSHIBA SD Memory Card Format utility does not format the
protected area of the SD/SDHC memory card - should you need to format
all areas of the memory card, including the protected area, you will need to
obtain an appropriate application that applies the copy protection system.

Media care
Observe the following precautions when handling the card.
Card care
■ Do not twist or bend cards.
■ Do not expose cards to liquids or store in humid areas or lay media
close to containers of liquid.
■ Do not touch the metal part of a card or expose it to liquids or let it get
dirty.
■ After using card, return it to its case.
■ The card is designed so that it can be inserted only one way. Do not try
to force the card into the slot.
■ Do not leave a card partially inserted in the slot. Press the card until you
hear it click into place.

User’s Manual 3-21

TECRA A10/S10/M10/SatellitePro S300

Memory card care

■ Set the write-protect switch to the lock position, if you do not want to
record data.
■ Memory cards have a limited lifespan, so it is important to backup
important data.
■ Do not write to a card if the battery power is low. Low power could
affect writing accuracy.
■ Do not remove a card while read/write is in progress.
For more details on using memory cards, see manuals accompanying
the cards.

About the write-protect

The following memory media have a function for protect.
■ SD Card (SD memory card, SDHC memory card)
■ Memory Stick (Memory Stick, Memory Stick PRO,
Memory Stick PRO Duo)
■ MultiMediaCard (MMC)
Set the write-protect switch to the lock position, if you do not want to
record data.

Inserting a memory media

The following instructions apply to all types of supported media devices.
To insert a memory media, follow the steps as detailed below:
1. Turn the memory media so that the contacts (metal areas) are face down.
2. Insert the memory media into the Bridge media slot on the left side of
the computer.
3. Press the memory media gently to ensure a firm connection is made.

Bridge media slot

Memory media

Figure 3-6 Inserting a memory media

3-22 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ Make sure memory media is oriented properly before you insert it.
If you insert the media in wrong direction, you may not be able to
remove it.
■ When inserting memory media, do not touch the metal contacts.
You could expose the storage area to static electricity, which can
destroy data.
■ Do not turn the computer off or switch to Sleep Mode or Hibernation
Mode while files are being copied - doing so may cause data to be lost.

Removing a memory media

The following instructions apply to all types of supported media devices.
To remove a memory media, follow the steps as detailed below:
1. Open the Safely Remove Hardware icon on the Windows Taskbar.
2. Point to memory media and click the left Touch Pad control button.
3. Press the memory media to partially extend it out of the computer.
4. Grasp the media and remove it.

Bridge media slot

Memory media

Figure 3-7 Removing memory media

■ Make sure the Bridge Media slot indicator is out before you remove
the memory media or turn off the computer’s power. If you remove the
memory media or turn off the power while the computer is accessing
the memory media, you may lose data or damage the media.
■ Do not remove the memory media while the computer is in Sleep or
Hibernation Mode. The computer could become unstable or data in the
memory media could be lost.
■ Do not remove only the miniSD/microSD Card while leaving the
adaptor in the Bridge Media slot.

User’s Manual 3-23

TECRA A10/S10/M10/SatellitePro S300

Additional memory module

You can install additional memory into the computer in order to increase the
amount of system memory that is available. This section describes how to
install and remove optional memory modules.
■ You should place a mat beneath the computer in order to prevent the
computer’s lid from becoming scratched or damaged when you are
installing/replacing the memory module. In this instance you should
avoid mats that are made of materials that hold or generate static
electricity.
■ When installing or removing a memory module, you must ensure that
you do not touch any other internal areas of the computer.
■ Insert the two memory modules into Slot A and Slot B respectively.
The computer will operate in dual channel mode.
You can access the inserted memory modules efficiently in dual channel.

■ Use only memory modules approved by TOSHIBA.

■ Do not try to install or remove a memory module under the following
conditions.
a. The computer is turned on.
b. The computer was shut down in either Sleep or Hibernation Mode.
c. Wake-up on LAN is enabled.
d. The wireless communication switch is turned on.
■ Be careful not to let screws or other foreign matter fall into the
computer. It could cause malfunction or electric shock.
■ Additional memory module is a precision electronic component that
may be fatally damaged by static electricity. Since the human body can
carry static electricity, it is important that you discharge yourself before
touching or installing any additional memory modules. To discharge
your body’s static electricity, simply touch any metal close to you with
bare hands.

Point to note about memory module error

If you install a memory module that is not compatible with the computer, the
Power indicator will flashes (on for 0.5 seconds, off for 0.5 seconds) in the
following ways;
■ If there is an error in only Slot A or no memory module is inserted in
Slot A: repeatedly flashes orange twice, then green.
■ If there is an error in Slot B: repeatedly flashes orange, then green twice.
■ If there are errors in both Slot A and Slot B: repeatedly flashes orange
twice, then green twice.
In all instances you should shut down the computer and remove the
incompatible module(s).
Use a point size 0 Phillips screwdriver to remove and fasten the screws -
the use of an incorrect screwdriver can damage the screw heads.

3-24 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Installing a memory module

To install a memory module, follow the steps as detailed below:
1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).
2. Remove the AC adaptor and all cables and peripherals connected to
the computer.
3. Close the display panel.
4. Turn the computer upside down and remove the battery pack (refer to
Replacing the battery pack section in Chapter 6, Power and Power-Up
Modes, if required).
5. Loosen the one screw securing the memory module cover in place -
please note that this screw is attached to the cover in order to prevent it
from being lost.
Use a point size 0 Phillips screwdriver.

6. Slide your fingernail or a thin object under the cover and lift it off.
Memory module
cover

Screw

Figure 3-8 Removing the memory module cover

7. Align the notch of the memory module with that of the memory slot and
gently insert the module into the slot at about a 45 degree angle before
holding it down until the latches on either side snap into place.

Notch

Slot B

Slot A

Figure 3-9 Seating the memory module

User’s Manual 3-25

TECRA A10/S10/M10/SatellitePro S300

■ Never allow metal objects, such as screws, staples and paper clips,
to enter the computer. Foreign metal objects can create a short circuit,
which can cause computer damage and fire, possibly resulting in
serious injury.
■ Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access
problems.

■ The slot A is reserved for the first memory module. Use the slot B for
expanded memory. If only one module is installed, use the slot A. When
inserting or removing memory modules, use the A and B marked on the
computer chassis to determine which slot is A and which is B.
■ Align the grooves along the edges of the memory module with the
locking tabs on the connector and insert the module into the connector
firmly - if you find it difficult to install the memory module, gently prise
the locking tabs outwards using the tip of your finger.
Please also ensure that you hold the memory module along its left and
right hand edges - the edges with the grooves in.

8. Seat the memory module cover in place and secure it with one screw.
Take care to ensure that the memory module cover is firmly closed.

Memory module cover

Screw

Figure 3-10 Seating the memory module cover

9. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.
10. Turn your computer over.
11. Turn the computer on and make sure the added memory is recognized -
to confirmed it, Start -> Control Panel -> System and Maintenance ->
System icon.

3-26 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Removing a memory module

To remove the memory module, follow the steps as detailed below:
1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).
2. Remove the AC adaptor and all cables and peripherals connected to
the computer.
3. Close the display panel.
4. Turn the computer upside down and remove the battery pack (refer to
Replacing the battery pack section in Chapter 6, Power and Power-Up
Modes, if required).
5. Loosen the one screw securing the memory module cover in place -
please note that this screw is attached to the cover in order to prevent it
from being lost.
6. Slide your fingernail or a thin object under the cover and lift it off.
7. Push the latches away from the module in order to release it - a spring
will force one end of the module up at an angle.
8. Grasp the module by its edges and remove it from the computer.
■ If you use the computer for a long time, the memory modules and the
circuits locating close to the memory modules will become hot. In this
case, let them cool to room temperature before you replace them.
Or you will get burnt if you touch any of them.
■ Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access
problems.

Latches

Figure 3-11 Removing the memory module

9. Seat the memory module cover in place and secure it with one screw.

User’s Manual 3-27

TECRA A10/S10/M10/SatellitePro S300

Take care to ensure that the memory module cover is firmly closed.

10. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.
11. Turn your computer over.

External monitor
An external analog monitor can be connected to the external monitor port
on the computer. To connect a monitor, follow the steps as detailed below:

Connecting the monitor cable

1. Turn the computer’s power off.
2. Connect the monitor cable to the external monitor port and tighten the
screws on the left and right hand side of the connector as required.

Monitor cable

External monitor port

Figure 3-12 Connecting the monitor cable to the external monitor port

3. Turn the external monitor’s power on.

4. Turn the computer’s power on.
When you turn on the power, the computer will automatically recognize the
monitor and determine whether it is a color or monochrome device. In the
event that you find that there are issues getting an image displayed on the
correct monitor, you should consider using the FN + F5 hot key to change
the display settings (if you then disconnect the external monitor before you
turn the computer’s power off, be sure to press FN + F5 hot key again to
switch to the internal display).
Please refer to Chapter 5, The Keyboard, for further details on using hot
keys to change the display setting.
Do not disconnect the external monitor while in Sleep or Hibernation Mode.
Turn off the computer before disconnecting the external monitor.

3-28 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

USB FDD Kit

The USB floppy diskette drive accommodates either a 1.44MB or 720KB
floppy diskette and connects to one of the computer’s USB ports.

USB connector

Disk-In-Use Indicator

Floppy diskette slot

Eject button
Figure 3-13 The USB floppy diskette drive

Connecting the USB floppy diskette drive

To connect the drive, plug the floppy diskette drive’s USB connector into a
computer’s USB port.
Make sure the connector is properly aligned with the socket. Do not try to
force the connection, doing so can damage the connecting pins.

USB port

USB connector

Figure 3-14 Connecting the USB floppy diskette drive

If you connect the USB floppy diskette drive after the computer has already
been turned on, it will take about ten seconds for it to be recognized by the
computer. Do not attempt to disconnect and reconnect the drive before this
period has elapsed.

User’s Manual 3-29

TECRA A10/S10/M10/SatellitePro S300

Disconnecting the USB floppy diskette drive

When you have finished using the USB floppy diskette drive, you can follow
the procedures below in order to disconnect it:
1. Wait for the Disk-In-Use Indicator light to go out to make sure all floppy
diskette activity has stopped.
If you disconnect the USB floppy diskette drive or turn off the power while
the computer is accessing the drive you may lose data or damage the
floppy diskette or the drive.

2. Click the Safely Remove Hardware icon on the Windows Taskbar.

3. Click the USB floppy diskette drive device that you want to remove.
4. Carefully pull the floppy diskette drive’s USB connector out from within
the computer’s USB port.

eSATA (External Serial ATA)

An device corresponding to eSATA function can be connected to the
eSATA/USB combo port on the computer.

Connecting the eSATA device

To connect an eSATA device, follow the steps as detailed below:
1. Connect an eSATA cable to the eSATA/USB combo port.
Make sure the connector is properly aligned with the socket.
Do not try to force the connection, doing so can damage the connecting
pins.

eSATA/USB
combo port

eSATA cable

Figure 3-15 Connecting an eSATA cable to the eSATA/USB combo port

3-30 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ A connected eSATA device may not be recognized if it is connected to

the computer’s eSATA/USB combo port while the computer is in Sleep
Mode or Hibernation Mode. If this occurs, disconnect the eSATA device
and then reconnect the device while the computer is turned on.
■ If you connect an eSATA device after the computer has already been
turned on, it will take about ten seconds for it to be recognized by the
computer.
■ Do not attempt to disconnect and reconnect the drive before this period
has elapsed.

Disconnecting an eSATA device

When you have finished using an eSATA device, you can follow the
procedures below in order to disconnect it:
1. Wait for the indicator light of an eSATA device to go out to make sure all
activity has stopped.
If you disconnect an eSATA device or turn off the power while the
computer is accessing the drive you may lose data or damage an eSATA
device or the drive.

2. Click the Safely Remove Hardware icon on the Windows Taskbar.

3. Click an eSATA device that you want to remove.
4. Carefully pull an eSATA device’s eSATA/USB combo connector out
from within the computer’s eSATA/USB combo port.

i.LINK (IEEE1394)
i.LINK (IEEE1394) is used for high-speed data transfer for a range of
compatible devices such as:
■ Digital video cameras
■ Hard disk drives
■ MO drives
■ Writable optical disc drives
Some models are equipped with a i.LINK (IEEE1394) port.
i.LINK uses a four-pin connector, which does not carry any electric current.
External devices will need their own power supply to operate.

Precautions
■ Make a back-up of your data before transferring it to the computer.
There is a possibility that the original data will be damaged. There is a
particular risk that some frames will be deleted in the case of digital
video transfer. TOSHIBA assumes no liability for such loss of data.
■ Do not transfer data in areas where static electricity is easily generated
or in areas subjected to electronic noise. Data can be destroyed.

User’s Manual 3-31

TECRA A10/S10/M10/SatellitePro S300

■ If you are transferring data through an IEEE1394 hub, do not connect or

disconnect other devices from the hub during data transfer. There is a
likelihood that data will be damaged. Connect all devices to the hub
before you turn on the computer’s power.
■ You may not use any copyrighted video or music data copied from a
video camera except for your personal enjoyment.
■ If you connect/disconnect an i.LINK device to/from another i.LINK
device that is currently exchanging data with the computer, data frames
might be dropped.
■ Make sure data transfer has ended or turn off the computer, before you:
■ Connect/disconnect an i.LINK device to/from the computer.
■ Connect/disconnect an i.LINK device to/from another i.LINK device
that is connected to the computer.

Connecting the i.LINK (IEEE1394) cable

To connect the i.LINK (IEEE1394) cable, follow the steps as detailed below:
1. Make sure the connectors are properly aligned and plug the i.LINK
(IEEE1394) cable into the computer.

i.LINK (IEEE1394) port

i.LINK (IEEE1394) connector

Figure 3-16 Connecting the i.LINK (IEEE1394) cable into the computer

2. Plug the other end of the cable into the device.

Note the following when you use i.LINK:
■ You may need to install drivers for your i.LINK devices.
■ Not all i.LINK devices have been tested. Therefore, compatibility with all
i.LINK devices cannot be guaranteed.
■ Some devices might not support sleep or automatic off functions.
■ Do not connect or disconnect an i.LINK device while it is using an
application or when the computer is automatically shutting it down to
save power. Data might be destroyed.

3-32 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Disconnecting the i.LINK (IEEE1394) cable

To disconnect the i.LINK (IEEE1394) cable, follow the steps as detailed
below:
1. Open the Safely Remove Hardware icon on the Windows Taskbar.
2. Point to i.LINK (IEEE1394) device and click.
3. Disconnect the cable from the computer then from the i.LINK device.
Refer also to the documentation that came with your i.LINK device.

Serial port
The serial connector can be used to connect to RS-232C compatible
devices.
RS-232C compatible devices include the following:
■ Modem
■ Mouse
■ Printer
Some models are equipped with a serial port.
To connect a serial port, follow the steps as detailed below:
1. Turn the computer’s power off.
2. Connect the serial connector to the serial port and tighten the screws on
the left and right hand side.

Serial connector

Serial port

Figure 3-17 Connecting the serial connector to the serial port

User’s Manual 3-33

TECRA A10/S10/M10/SatellitePro S300

TOSHIBA Express Port Replicator

In addition to the ports available on the computer, the TOSHIBA Express
Port Replicator. The TOSHIBA Express Port Replicator connects directly to
the docking interface on the underside of the computer. The AC adaptor
connects the TOSHIBA Express Port Replicator to a power source.
The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.

■ You must connect the AC adaptor before you connect to a TOSHIBA

Express Port Replicator.
■ When a TOSHIBA Express Port Replicator is connected to the
computer, you can not use the following computer’s ports: LAN jack,
DC IN 15V jack and External monitor port.
■ When connecting an AC Adaptor to the TOSHIBA Express Port
Replicator, use only the AC Adaptor included with TOSHIBA Express
Port Replicator. Do not use the computer’s AC Adaptor.

The following ports are available on the TOSHIBA Express Port Replicator.
■ RJ45 LAN jack
■ External monitor port
■ DC IN 15V jack
■ Security lock slot
■ Universal Serial Bus 2.0 port (four)
■ DVI port
■ As the port operation of all DVI (Digital Visual Interface) monitors has
not been confirmed, some DVI monitors may not function properly.
■ Set the TOSHIBA Express Port Replicator’s Slide Adjuster to SLIDE
position #3 or #5 when connecting this computer to the TOSHIBA
Express Port Replicator. Refer to the TOSHIBA Express Port
Replicator User’s Manual for more details on connection methods.

3-34 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Security lock
A security locks enable you to anchor your computer a desk or other heavy
object in order to help prevent unauthorized removal or theft. The computer
has a security lock slot on its right side into which you can attach one end of
the security cable, while the other end attaches to a desk or similar object.
The methods used for attaching security cables differ from product to
product. Please refer to the instructions for the product you are using for
more information.

Connecting the security lock

In order to connect a security cable to the computer, follow the steps as
detailed below:
1. Turn the computer so its right hand side faces you.
2. Align the security cable with the “lock hole” and secure it in place.

Security lock slot

Figure 3-18 Security lock

User’s Manual 3-35

TECRA A10/S10/M10/SatellitePro S300

Optional accessories
You are able to add a number of options and accessories in order to make
your computer even more powerful and convenient to use. For reference,
the following list details some of the items that are available from your
reseller or TOSHIBA dealer:

DDR2-667 A 512MB, 1,024MB or 2,048MB memory module

Memory Kit (DDR2-667) can easily be installed in the
computer.
DDR2-800 A 1,024MB, 2,048MB or 4,096MB memory
Memory Kit module (DDR2-800) can easily be installed in the
computer.
Universal AC If you frequently use your computer at more than
Adaptor one site, it may be convenient to purchase an
additional AC adaptor to be kept at each site in
order to remove the need to always carry the
adaptor with you.
Battery Pack An additional battery pack can be purchased for
use as either a spare or replacement. Please
refer to Chapter 6, Power and Power-Up Modes,
for further information.
High Capacity An additional battery pack can be purchased for
Battery Pack use as either a spare or replacement.
Extended Capacity An additional battery pack can be purchased for
Battery Pack use as either a spare or replacement.
Battery Charger The optional battery charger allows you to
charge extra battery packs outside of having to
use the computer.
USB FDD Kit The USB floppy diskette drive accommodates
either a 1.44MB or 720KB floppy diskette through
connection to one of the computer’s USB ports.
In use, please be aware that, while you cannot
format 720KB floppy diskettes under Windows
Vista, you are able to read and write to diskettes
that have already been formatted.
TOSHIBA Express The TOSHIBA Express Port Replicator provides
Port Replicator the ports available on the computer in addition to
a digital visual interface (DVI) port, External
monitor port, four Universal Serial Bus ports
(USB 2.0) and a LAN jack.

3-36 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 4

Operating Basics
This chapter describes the basic operations of your computer, highlights
the precautions that should be taken when using it.

TOSHIBA Dual Pointing Device

Some models are equipped with a dual point system: a Touch Pad and an
AccuPoint pointing stick.
Using the Touch Pad
To use the Touch Pad, simply touch and move your fingertip across it in the
direction you want the on-screen pointer to go.
AccuPoint Fingerprint Sensor

AccuPoint
control buttons

Touch Pad control buttons

Touch Pad

Figure 4-1 Touch Pad and Touch Pad control buttons

The two buttons below the Touch Pad are used like the buttons on a standard
mouse - press the left button to select a menu item or to manipulate text or
graphics designated by the pointer, and press the right button to display a
menu or other function depending on the software you are using.
You can also tap the Touch Pad to perform functions similar to those of the
left button on a standard mouse.
Click: Tap once
Double-click: Tap twice
Drag and drop: Tap to select the item(s) you want to move, leave your
finger on the Touch Pad after the second tap and then move the item(s)
to their new destination.

User’s Manual 4-1

TECRA A10/S10/M10/SatellitePro S300

Using the AccuPoint

To use the AccuPoint, simply push it with your finger tip in the direction you
want to move the on-screen pointer.
Two buttons above the Touch Pad work in the same way with the AccuPoint
as they do with the Touch Pad. Refer to the Using the Touch Pad section
for details.
Some models are equipped with an AccuPoint.

AccuPoint precautions
Certain conditions can affect the on-screen pointer when using AccuPoint.
For example, the pointer may travel contrary to AccuPoint operation or an
error message may appear, if
■ You touch the AccuPoint during power-up.
■ You apply constant, soft pressure during power-up.
■ There is a sudden temperature change.
■ Strong stress is applied to the AccuPoint.
If an error message appears, reboot the computer. If an error message does
not appear, wait a moment for the pointer to stop, then continue operation.

Replacing the cap

The AccuPoint cap is an expendable item that should be replaced after
prolonged use. The spare AccuPoint cap is supplied with the computer.
1. To remove the AccuPoint cap, firmly pinch the cap and pull it
straight up.

AccuPoint cap

Figure 4-2 Removing the AccuPoint cap

2. Position a new cap on the peg and press it into place.

The peg is square, so be careful to align the cap’s square hole with
the peg.

4-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Using the Fingerprint Sensor

This product has a fingerprint utility installed for the purpose of enrolling
and recognizing fingerprints. By enrolling the ID and password onto the
fingerprint authentication feature, it is no longer necessary to input the
password from the keyboard. Fingerprint feature enables you to:
■ Logon to Windows and access a security enabled homepage through
Internet Explorer.
■ Files and folders can be encrypted/decrypted and third party access to
them prevented.
■ Disable the password-protected screen-saver when returning from a
power-saving mode such as Sleep Mode.
■ Authentication of the User Password (and, if applicable, the HDD (Hard
Disk Drive) Password) when booting up the computer (Pre-OS
Authentication).
■ Single-Swipe Sign On feature
Fingerprint cannot be used in models that do not have a fingerprint module
installed.

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or
authentication will help to minimize authentication failures:
Align the first joint of the finger to the center of the sensor. Lightly touch the
sensor and swipe finger levelly towards you until the sensor surface
becomes visible. In performing this process, you should also take care to
ensure that the center of your fingerprint is on the sensor.
The following illustrations show the recommended way to swipe your finger
over the fingerprint sensor.

Sensor

Sensor

Figure 4-3 Swipe the finger

User’s Manual 4-3

TECRA A10/S10/M10/SatellitePro S300

■ Avoid swiping with your finger stiff or pressed too hard onto the sensor,
and take care to ensure that the center of the fingerprint is touching the
sensor before swiping. Either of these conditions may cause fingerprint
reading to fail.
■ Check the center of the fingerprint whorl before swiping and then
ensure this is swiped along the center line of the sensor.
■ There is a possibility of authentication failures if the finger is swiped too
quickly or too slowly - follow any on-screen instructions to adjust the
speed used during the swipe process.

Points to note about the Fingerprint Sensor

Please be aware of the following considerations when using the fingerprint
sensor. A failure to follow these guidelines might result in damage to the
sensor, sensor failure, fingerprint recognition problems or a lower
fingerprint recognition success rate.
■ Do not scratch or poke the sensor with your nails or any hard or sharp
objects.
■ Do not press the sensor strongly.
■ Do not touch the sensor with a wet finger or any wet objects - keep the
sensor surface dry and free from water vapor.
■ Do not touch the sensor with a soiled or dirty finger as minute foreign
particles of dust and dirt may scratch it.
■ Do not paste stickers or write on the sensor.
■ Do not touch the sensor with a finger or any other object which may
have a build-up of static electricity on it.
Observe the following before you place your finger on the sensor whether
for fingerprint enrollment/registration or recognition.
■ Wash and dry your hands thoroughly.
■ Remove static electricity from your fingers by touching any metal
surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.
■ Clean the sensor with a lint-free cloth - do not use detergent or any
other chemicals to clean the sensor.
■ Avoid the following finger conditions for enrollment or recognition as
they may result in fingerprint enrollment errors or a drop in the
fingerprint recognition success rate
■ Soaked or swollen finger, for example as may occur after taking a
bath.
■ Injured finger
■ Wet finger
■ Soiled or oily finger
■ Extremely dry skin condition on finger

4-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Observe the following to improve the fingerprint recognition success rate.

■ Enroll two or more fingers.
■ Enroll additional fingers if a recognition failure often occurs when using
already enrolled fingers.
■ Check the condition of your finger - any conditions which have changed
since enrollment, such as injury, rough skin, and extremely dry, wet,
soiled, dirty, oily, soaked or swollen fingers, may lower the recognition
success rate. Also if the fingerprint is worn down or the finger becomes
thinner or fatter, the recognition success rate may be lowered.
■ As the fingerprint for each finger is different and unique you should
ensure that only the registered or enrolled fingerprint or fingerprints are
used for identification.
■ Check the position and speed at which you swipe your finger across the
sensor - please refer to the preceding drawing.
■ The fingerprint sensor compares and analyzes the unique
characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.
■ The recognition success rate may differ from user to user.

Setup Procedure
Please use the following procedure when first using fingerprint
authentication.

Fingerprint Registration
You should initially enroll the required authentication data using the
Fingerprint Enrollment Wizard.
■ In use, the fingerprint authentication system will use the same
username and password as defined within the Windows operating
system. If no Windows password has been configured, you must do
this before starting the fingerprint registration process.
■ This sensor has the memory space for at least twenty-one fingerprint
patterns. You might be able to register more fingerprint patterns
depending on the sensor memory usage.

1. To run this program, click Start -> All Programs -> TrueSuite Access
Manager -> TrueSuite Access Manager.

You are also able to start the Fingerprint Enrollment Wizard by using the
following methods.
■ Click the Fingerprint Application icon in the Taskbar.

2. The Verify screen will be displayed, enter the Windows logon password
and click the Next button.

User’s Manual 4-5

TECRA A10/S10/M10/SatellitePro S300

3. On the User’s Fingers screen click the box above the finger you wish
to register.
If any of the previously enrolled fingerprints is selected again, the latest
information will be enrolled and any previous information over-written.
4. The Fingerprint Enrollment screen will be displayed and the tutorial
will begin. First click “Replay video” and confirm the proper movement
for the finger you wish to register. Then confirm the message displayed
on this screen and ensure that there is a check mark in the Run
Interactive Tutorial box. Once this has been done, click Next.
5. At the Scanning Practice screen, you are able to practice swiping
(three times) your finger to ensure you use the correct method. Click
“Try again” to if you wish to practice again. You have finished practicing,
click Next button.
6. Register your fingerprint on the Fingerprint Image Capture screen.
Let the computer read the finger to be registered 3 times. An image of
your fingerprint will be shown on the screen each time the fingerprint is
successfully read.
Once the fingerprint is successfully read for the third time, the message
Successfully combined will be displayed beneath the fingerprint
images. Click the Next button.
7. When the Store To Sensor screen is displayed, check Store
fingerprint to Sensor. Click Finish to complete fingerprint registration.
It is strongly recommended that you register 2 or more fingerprints.
Repeat the procedure from step 3 to register another fingerprint.

How to Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the
fingerprint sensor. Therefore, if you give the computer to someone else, or
dispose of it in any way, the following process is recommended to delete
your fingerprint information:
1. To run this program, click Start -> All Programs -> TrueSuite Access
Manager -> TrueSuite Access Manager.
2. The Verify screen will be displayed, so either swipe your registered
finger or enter the Windows logon password and click the Next button.

4-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

3. The User’s Fingers screen is displayed.

■ To delete all registered fingerprints
1. Click Delete All Fingerprints.
2. Follow the on-screen instructions to deleted the registered
fingerprints.
■ To delete individual fingerprints
1. Click the fingerprint mark above the registered finger.
2. Click Delete All Fingerprints.
3. “Are you sure you want to delete this fingerprint?” will be displayed
on the screen, click Yes button.
4. When Delete All Fingerprints is selected, the user selection
screen will be displayed, so select which user’s fingerprint data to
delete.
■ Selecting “Delete current user’s fingerprints” will delete the
fingerprint data for the currently logged in user.
■ Selecting “Delete all users’ fingerprints” will delete the
fingerprint data for all users, however this item can only be
selected if the currently logged in user has administrator
privileges.
5. A message will be displayed asking for confirmation to delete the
fingerprint data, click the Yes button.
In use, please be aware of the following limitations of the fingerprint sensor:
■ A warning message will be displayed when recognition is abnormal or
recognition is not successful within a fixed duration.
■ The fingerprint sensor compares and analyzes the unique
characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.
■ The recognition success rate may differ from user to user.
■ Toshiba does not guarantee that this fingerprint recognition technology
will be error-free.
■ Toshiba does not guarantee that the fingerprint sensor will recognize
the enrolled user or accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out
of the use of this fingerprint recognition software or utility.

User’s Manual 4-7

TECRA A10/S10/M10/SatellitePro S300

Points to note about the Fingerprint Utility software

You are able to backup saved fingerprint data and information within the by
using the Import or Export User Data facility under the fingerprint
management software. However, please be aware that any encrypted files
cannot be backup within File protection using this function - in these
instances it is recommended that you backup these files to external media
using standard file copy processes.

The Encrypting File System (EFS) is a Windows Vista feature.

If a file is encrypted using EFS, it cannot be encrypted further using the
fingerprint authentication function.

Windows Logon via Fingerprint Authentication

If required, you are also able to use fingerprint authentication in place of the
usual Windows logon process using your username and password.
This method is especially useful where there are many users using the
same computer as it removes the need for actual user selection when the
system is started.

Fingerprint Authentication Procedure

1. Start up the computer.
2. At the Windows Welcome screen, choose any of the enrolled fingers
and swipe the fingerprint on the sensor - if the authentication process is
successful, the user will automatically be logged in to Windows.
If the fingerprint authentication process fails you will need to log into
Windows using the appropriate username and password. In addition, you
should use this manual login process if fingerprint authentication fails for
three consecutive tries - a warning message will be displayed when
authentication is not normal or is not successful within a fixed duration.

Fingerprint Pre-OS Authentication

General
The fingerprint authentication system can be used to replace the keyboard
based password authentication system that is used when the computer is
turned on.
If you do not want to use the fingerprint authentication system for password
authentication while booting up the computer, instead you prefer using the
keyboard entry method, simply press the BACK SPACE key when the
Fingerprint Pre-OS Authentication screen is displayed.
Using this process will switch the password input screen across to the
keyboard based entry screen.

4-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ You must ensure that you use the TOSHIBA Password Utility to
register a User Password before using the Fingerprint Pre-OS
Authentication and its extended function to allow fingerprints to be used
to access the computer when it is turned on.
■ If the fingerprint authentication process fails five times, a preset time
limit is exceeded, or you press the BACK SPACE key, [Password =]
will be displayed on the screen and you will have to enter either the
User Password or Supervisor Password manually in order to start the
computer.
■ When swiping your finger, please ensure that you do it slowly and at a
constant speed. If you find that this does not improve the authentication
rate, you should try to adjust the speed at which the finger is swiped.
■ If there are any changes in the environment or settings related to
authorization, you will be required to provide authorization information
such as a User Password (and, if applicable, the HDD (Hard Disk
Drive) password).

How to Enable Fingerprint Pre-OS Authentication Settings

It is necessary to first enroll your fingerprint with the Fingerprint Application
prior to enabling and configuring the Fingerprint Pre-OS Authentication
System. You should check that your fingerprint is enrolled before
configuring the settings (please refer to the Manual for Fingerprint
Registration/Enrollment for further instructions).
1. To run this program, click Start -> All Programs -> TrueSuite Access
Manager -> Fingerprint Application with Admin.
2. User Account Control screen is displayed, click the Allow button.
This setting can only be changed if the currently logged in user has
administrator privileges.
3. Swipe a registered finger on the fingerprint sensor.
4. Click the Setting menu at the TrueSuite Access Manager screen.
5. Administrator Setting screen is displayed, check the “Enable Pre-OS
Fingerprint Authentication” check box and then click OK.
6. Click the Exit button at the TrueSuite Access Manager screen.

Fingerprint Single-Swipe Sign On Feature

General
This is a feature that allows the user to complete the authentication for both
the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive)
Password) and logging onto Windows using only one fingerprint
authentication when booting up.

User’s Manual 4-9

TECRA A10/S10/M10/SatellitePro S300

It is necessary to register the User/BIOS Password and Windows Logon

Password before using the Fingerprint Pre-OS Authentication and this
Fingerprint Single-Swipe Sign On Feature. Please use the TOSHIBA
Password Utility to register your User/BIOS Password. If Windows Logon is
not the default for your system, see Manual to register your Windows
Logon Password.
Only one fingerprint authentication is required to replace the User/BIOS
Password (and, if applicable, the HDD(Hard Disk Drive) Password) and the
Windows Logon Password.

How to Enable Fingerprint Single-Swipe Sign On Feature

It is necessary to first enroll your fingerprint with the Fingerprint application
prior to enabling and configuring the Fingerprint Single-Swipe Sign On
feature. You should check that your fingerprint is enrolled before
configuring the settings (please refer to the Manual for Fingerprint
Registration/Enrollment for further instructions).
1. To run this program, click Start -> All Programs -> TrueSuite Access
Manager -> Fingerprint Application with Admin.
2. User Account Control screen is displayed, click the Allow button.
This setting can only be changed if the currently logged in user has
administrator privileges.
3. Swipe a registered finger on the fingerprint sensor.
4. Click the Setting menu at the TrueSuite Access Manager screen.
5. Administrator Setting screen is displayed, check the “Enable Single-
Sign On Fingerprint Authentication” check box and then click OK.
6. Click the Exit button at the TrueSuite Access Manager screen.

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be
completely secure or error-free, or that it will accurately screen out
unauthorized users at all times. TOSHIBA is not liable for any failure or
damage that might arise out of the use of the fingerprint software.
■ The fingerprint sensor compares and analyzes the unique
characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.
■ The recognition success rate may differ from user to user.

4-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Web Camera
Web Camera is a device that allows you to record video or take
photographs with your computer. You can use it for video chatting or video
conferences using a communication tool such as Windows Live
Messenger. Camera Assistant Software will help you to add various
video effects to your video or photograph.
Enables the transmission of video and use of video chat via the internet
using specialized applications.
The effective pixel count for this web camera is 1.31 million (maximum
photograph size: 1280x1024 pixels).
Some models are equipped with a Web Camera.
Please refer to the Camera Assistant Software Online Help for details.

Web Camera
Web Camera LED

Figure 4-4 Web Camera

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may
reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other
soft cloth to clean the lens if it becomes dirty.
■ Setting the [Size] to more than “800x600” will cause a larger amount of
data to be written to the hard disk drive and may interfere with smooth
recording.

User’s Manual 4-11

TECRA A10/S10/M10/SatellitePro S300

Using the TOSHIBA Face Recognition

TOSHIBA Face Recognition uses a face verification library to verify the face
data of users when they log in to Windows. The user can thus avoid having
to enter a password or the like, which makes the login process easier.
■ TOSHIBA Face Recognition does not guarantee the correct identification
of a user. Changes to the likeness of a registrant, such as hair style
changes, wearing a cap, or wearing glasses may effect the recognition
rates when such changes occur after the registrant had registered.
■ TOSHIBA Face Recognition may incorrectly recognize faces that are
similar to a registrant.
■ For high security purposes, TOSHIBA Face Recognition is not a
suitable substitute for Windows passwords. When security is a high
priority, use your established Windows passwords to log in.
■ Bright background light and/or shadows may prevent a registrant from
being recognized correctly. In that case, log in using your Windows
password. If recognition of a registrant fails repeatedly, refer to your
computer documentation to learn ways to improve recognition
performance.
■ TOSHIBA Face Recognition records face data in a log when face
recognition fails. When transferring ownership or disposing of your
computer, please uninstall the application or delete all the logs created
by the application. For details on how to do this, see help file.
■ When using the feature “Log Record function” of the Toshiba Face
Recognition software please make sure that the usage is in line with
applicable legal requirements especially data protection laws in your
country of usage as well as with company internal regulations if any.

Disclaimer
Toshiba does not guarantee that the face recognition utility technology will
be completely secure or error-free. Toshiba does not guarantee that the
face recognition utility will accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out of
the use of the face recognition software or utility.
TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,
PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE
OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.

4-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed
when you log in. To register the data needed when you log in, follow the
steps as described below:
1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> TOSHIBA Face Recognition.
■ The Registration screen is displayed for a logged-in user whose
face has not been registered.
■ The Management screen is displayed for a logged-in user whose
face has already been registered.
2. If you are a registered user, click the Register face button in the
Management screen, otherwise the Registration screen will be
displayed.
■ If you wish to practice, click on the Next button in the Registration
screen.
■ If you do not wish to practice, click on the Skip button in the
Registration screen.
3. Click the Next button to start the guide.
4. First, take a picture while moving your neck slightly to the left and right.
5. Now take a picture while moving your neck down and up.
■ Click the Back button to practice the guide once more.
6. Click the Next button to start image-capturing process. Adjust the
position of your face so that it fits within the face-shaped frame.
7. Once your face has been positioned properly, the recording will
commence. Start moving your neck very slightly to the left and right,
and then move your neck down and up.
8. Registration will end after you have repeatedly moved your neck left,
right, down and up. When the register succeeds, below message will be
displayed on the screen:
“ Registration successful. Now we’ll do the
verification test. Click the Next button.”.
Click the Next button to perform the verification test.
9. Perform the verification test. Face the screen as you do when you
register.
■ If verification fails, click the Back button and re-register. Please refer
from step 6 to step 8.
10. If verification is successful, click the Next button and register an
account.
11. Register the account.
Fill in the account registration fields.
Fill in the all fields.
12. The Management screen is displayed.
The registered account name will be displayed. Clicking on it will cause
the captured image of your face to be displayed on the left.

User’s Manual 4-13

TECRA A10/S10/M10/SatellitePro S300

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created
during registration. To delete the Face Recognition Data, follow the steps
as described below:
1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> TOSHIBA Face Recognition.
The Management screen is displayed.
2. Select a user which is deleted in the Management screen.
3. Click the Delete button. “You are about to delete the user
data. Would you like to continue?” will be displayed on the
screen.
■ If you do not want the data to be deleted, click the No button and
you will then be returned to the Management screen.
■ Clicking on the Yes button will remove the selected user from the
Management screen.

How to launch the help file

For further information on this utility, please refer to help file.
1. To launch the help file, click Start -> All Programs -> TOSHIBA ->
Utilities -> TOSHIBA Face Recognition Help.

Windows Logon via TOSHIBA Face Recognition

This section explains how to login to Windows with TOSHIBA Face
Recognition. Two authentication modes are provided.
■ AUTO Mode Login screen: If the face authentication tile is selected by
default, you can log in without using the keyboard or mouse.
■ 1:1 Mode Login screen: This mode is essentially the same as AUTO
mode, but the Select Account screen will appear before the Display
Captured Image screen, and you will need to select the user account
to be authenticated in order to start the authentication process.

AUTO Mode Login screen

1. Turn on the computer.
2. The Select Tiles screen will be displayed.
3. Select Start face recognition ( ).
4. “Please turn your face to the camera” will be displayed.
5. Verification will be performed. If the authentication is successful, the
image data taken in step 4 will be faded in and placed over one another.
■ If an error occurs during authentication, you will be returned to the
Select Tiles screen.
6. Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

4-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

1:1 Mode Login screen

1. Turn on the computer.
2. The Select Tiles screen will be displayed.
3. Select Start face recognition ( ).
4. The Select Account screen will be displayed.
5. Select the account, and click the arrow button.
6. “Please turn your face to the camera” will be displayed.
7. Verification will be performed. If the authentication is successful, the
image data taken in step 6 will be faded in and placed over one another.
■ If an error occurs during authentication, you will be returned to the
Select Tiles screen.
8. Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

Using optical disc drives

The full-size drive provides high-performance execution of
CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or
8 cm (3.15") CD/DVDs without an adaptor. A Serial ATA interface controller
is used for CD/DVD-ROM operation. When the computer is accessing a
CD/DVD-ROM, an indicator on the drive glows.
Use the DVD playback application to view DVD-Video discs.

If you have a DVD-ROM & CD-R/RW drive, refer also to the Writing
CD/DVDs on DVD Super Multi drives section for precautions on writing
to CDs.
If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on
DVD Super Multi drives section for precautions on writing to CDs/DVDs.

User’s Manual 4-15

TECRA A10/S10/M10/SatellitePro S300

Loading discs
To load CD/DVDs, follow the steps as detailed below:
1. When the computer’s power is on, press the eject button to open the
disc tray slightly.
2. Grasp the disc tray gently and pull until it is fully opened.

Disc tray

Eject button

Figure 4-5 Pressing the eject button and pulling the disc tray open

3. Lay the CD/DVD, label side up, in the disc tray.

Laser lens

Figure 4-6 Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend
slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD
at an angle when you place it in the disc tray. After seating the CD/DVD,
however, make sure it lies flat.

4-16 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ Do not touch the laser lens or any portion of its surrounding casing as
this could cause misalignment.
■ Prevent foreign objects from entering the drive. Check the surface of
the disc tray, especially the area behind the front edge of the disc tray,
to make sure there are no such objects before closing the drive.

4. Press gently at the center of the CD/DVD until you feel it click into
place. The CD/DVD should lie below the top of the spindle, flush with
the spindle base.
5. Push the center of the disc tray to close it. Press gently until it locks
into place.
If the CD/DVD is not seated properly when the disc tray is closed, the
CD/DVD might be damaged. Also, the disc tray might not open fully when
you press the eject button.

Figure 4-7 Closing the CD/DVD disc tray

Removing discs
To remove the CD/DVD, follow the steps as detailed below:
Do not press the eject button while the computer is accessing the media
drive. Wait for the optical disc drive indicator to go out before you open the
disc tray. Also, if the CD/DVD is spinning when you open the disc tray, wait
for it to stop before you remove it.

1. To pop the disc tray partially open, press the eject button. Gently pull
the disc tray out until it is fully opened.
When the disc tray pops open slightly, wait a moment to make sure the
CD/DVD has stopped spinning before pulling the disc tray fully open.

User’s Manual 4-17

TECRA A10/S10/M10/SatellitePro S300

2. The CD/DVD extends slightly over the sides of the disc tray so you can
grasp it. Gently lift out the CD/DVD.

Figure 4-8 Removing a CD/DVD

3. Push the center of the disc tray to close it. Press gently until it locks into
place.

How to remove CD/DVD when the disc tray will not open
Pressing the eject button will not open the disc tray when the computer
power is off. If the power is off, you can open the disc tray by inserting a
slender object (about 15 mm) such as a straightened paper clip into the
eject hole near the eject button.

Eject hole

Figure 4-9 Manual release with the eject hole

Turn off the power before you use the eject hole. If the CD/DVD is spinning
when you open the disc tray, the CD/DVD could fly off the spindle and
cause injury.

4-18 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Writing CDs on DVD-ROM & CD-R/RW drives

Depending on the type of drive installed, you may be able to write CDs.
The DVD-ROM & CD-R/RW drive lets you write as well as read CD-ROMs.
Observe the precautions in this section to ensure the best performance for
writing CDs. For information on loading and unloading CDs refer to the
Media care section.
■ Please refer to the Writable discs, Chapter 2 for details about the types
of writable CD and DVD discs that can be supported by this computer.
■ Do not turn off the power to the optical disc drive while the computer is
accessing it as this may cause you to lose data.
■ To write data to CD-R/-RW media, use the TOSHIBA Disc Creator
feature that is installed on your computer.

When writing information to media using an optical drive, you should

always ensure that you connect the AC adaptor to a live power socket. It is
possible that, if data is written while powered by the battery pack, the write
process may sometimes fail due to low battery power - in these instances
data loss may occur.

Before writing or rewriting

■ Based on TOSHIBA’s limited compatibility testing, we suggest the
following manufacturers of CD-R, CD-RW media, however, it must be
noted that disc quality can affect write or rewrite success rates. Please
also be aware that in no event does TOSHIBA guarantee the operation,
quality or performance of any disc.

CD-R:
TAIYO YUDEN CO., Ltd.
MITSUBISHI KAGAKU MEDIA CO., LTD.
Ricoh Co., Ltd.
Hitachi Maxell,Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.
Ricoh Co., Ltd.

CD-RW: (Ultra-Speed)
MITSUBISHI KAGAKU MEDIA CO., LTD.
■ If the disc is poor in quality, or is dirty or damaged, writing or rewriting
errors may be noted - ensure that you check all discs for dirt or damage
before you use them.
■ The actual number of rewrites to CD-RW media will be affected by the
quality of the disc itself and the way in which it is used.
■ Data written to a CD-R disc cannot be deleted either in whole or in part.

User’s Manual 4-19

TECRA A10/S10/M10/SatellitePro S300

■ Data deleted/erased from a CD-RW disc cannot be recovered. You

must check the content of the disc carefully before you delete it, taking
care that, if multiple drives that can write data to discs are connected,
you do not delete data from the wrong one.
■ When multiple drives that can write data to discs are connected, be
sure that you do not write to or delete data from the wrong drive.
■ Be sure to connect the AC adaptor to the computer before you write or
rewrite any information.
■ Be sure to close all other software programs except for the writing
software itself.
■ Do not run software such as a screen saver which can put a heavy load
on the processor.
■ Operate the computer at its full power settings - do not use any
power-saving features.
■ Do not write information while virus checking software is running,
instead wait for it to finish, then disable the virus protection applications,
including any software that checks files automatically in the
background.
■ Do not use any hard disk utilities, including those that are intended to
enhance hard disk drive access speeds, as they may cause unstable
operation and damage data.
■ CD-RW (Ultra Speed +) media should not be used as data may be lost
or damaged.
■ You should always write from the computer’s hard disk drive onto the
CD/DVD - do not try to write from shared devices such as a server or
any other network device.
■ Writing with software other than TOSHIBA Disc Creator has not been
confirmed, therefore operation with other software applications cannot
be guaranteed.

4-20 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

When writing or rewriting

Please observe the following points while you write or rewrite data to CD-R,
CD-RW media:
■ Always copy data from the hard disk drive to the optical media - do not
use the cut-and-paste function as the original data will be lost if there is
a write error.
■ Do not perform any of the following actions:
■ Change users in the Windows Vista operating system.
■ Operate the computer for any other function, including such tasks as
using a mouse or Touch Pad, or closing/opening the display panel.
■ Start a communication application such as a modem.
■ Apply impact or vibration to the computer.
■ Install, remove or connect external devices, including such items as
a PC Card, SD/SDHC memory card, miniSD/microSD Card, Smart
Card, Memory Stick/Memory Stick PRO/Memory Stick PRO Duo, xD
picture card, MultiMediaCard, USB device, external monitor, i.LINK
device, or an optical digital device.
■ Use the audio/video control button to reproduce music or voice.
■ Open the optical disc drive.
■ Do not use shut down, log off, Sleep Mode or Hibernation Mode
functions while writing or rewriting.
■ Make sure that the write/rewrite operation is completed before going
into either Sleep Mode or Hibernation Mode (writing is completed if you
can remove an optical media on the DVD-ROM&CD-R/RW drive).
■ If the media is of poor quality, or is dirty or damaged, writing or rewriting
errors may occur.
■ Set the computer on a level surface and avoid places subject to
vibration such as airplanes, trains or cars. In addition, do not use the
computer on an unstable surface such as a stand.
■ Keep mobile phones and other wireless communication devices away
from the computer.

User’s Manual 4-21

TECRA A10/S10/M10/SatellitePro S300

Writing CD/DVDs on DVD Super Multi drives

You can use the DVD Super Multi drive to write data to either CD-R,
CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double
Layer), DVD+RW or DVD-RAM discs. The TOSHIBA Disc Creator is
provided as writing software with this computer.
■ Please refer to the Writable discs, Chapter 2 for details about the types
of writable CD and DVD discs that can be supported by this computer.
■ Do not turn off the power to the optical disc drive while the computer is
accessing it as this may cause you to lose data.
■ To write data to CD-R/-RW media, use the TOSHIBA Disc Creator
feature that is installed on your computer.

When writing information to media using an optical drive, you should

always ensure that you connect the AC adaptor to a live power socket. It is
possible that, if data is written while powered by the battery pack, the write
process may sometimes fail due to low battery power - in these instances
data loss may occur.

Important message
Before you write or rewrite to any of the media supported by the DVD
Super Multi Drive, please read and follow all of the setup and operating
instructions in this section. If you fail to do so, you may find that the DVD
Super Multi drive may not function properly, and you may fail to write or
rewrite information successfully - this may cause you to either lose data or
incur other damage to the drive or media.

Disclaimer
TOSHIBA does not bear responsibility for the following:
■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW,
DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM disc that may
be caused by writing or rewriting with this product.
■ Any change or loss of the recorded contents of CD-R, CD-RW, DVD-R,
DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer),
DVD+RW or DVD-RAM media that may be caused by writing or
rewriting with this product, or for any business profit loss or business
interruption that may be caused by the change or loss of the recorded
contents.
■ Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. In view of this, it is good practice to make
two or more copies of important data, in case of any undesired change or
loss of the recorded contents.

4-22 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Before writing or rewriting

■ Based on TOSHIBA’s limited compatibility testing, we suggest the
following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual
Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or
DVD-RAM media, however, it must be noted that disc quality can
affect write or rewrite success rates. Please also be aware that in no
event does TOSHIBA guarantee the operation, quality or performance
of any disc.

CD-R:
TAIYO YUDEN CO., Ltd.
MITSUBISHI KAGAKU MEDIA CO., LTD.
Ricoh Co., Ltd.
Hitachi Maxell,Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.
Ricoh Co., Ltd.

CD-RW: (Ultra-Speed)
MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD-R:
DVD Specifications for Recordable Disc for General Version 2.0
TAIYO YUDEN Co., Ltd. (for 8x and 16x speed media)
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed
media)
Hitachi Maxell, Ltd. (for 8x and 16x speed media)

DVD-R (Dual Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

DVD+R:
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed
media)
Ricoh Co., Ltd. (for 8x and 16x speed media)
TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media)
DVD+R (Double Layer):
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed
media)
DVD-RW:
DVD Specifications for Recordable Disc for Version 1.1 or
version 1.2
Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media)
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed
media)

User’s Manual 4-23

TECRA A10/S10/M10/SatellitePro S300

DVD+RW:
Ricoh Co., Ltd. (for 2.4x, 4x and 8x speed media)
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x, 4x and 8x speed
media)
DVD-RAM: (DVD Super Multi drive only)
DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1
or Version 2.2
Matsushita Electric Industrial Co.,Ltd. (for 3x and 5x speed media)
Hitachi Maxell, Ltd. (for 3x and 5x speed media)

■ DVD Super Multi drive cannot use discs that allow writing faster than
16x speed (DVD-R and DVD+R media), 8x speed (DVD-R (Dual
Layer), DVD+RW and DVD+R (Double Layer) media),
6x speed (DVD-RW media), 5x speed (DVD-RAM media).
■ Some types and formats of DVD-R (Dual Layer) and DVD+R (Double
Layer) discs may be unreadable.
■ 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.
■ DISC created in DVD-R (Dual Layer) format4 (Layer Jump Recording)
cannot be read.

■ If the disc is poor in quality, or is dirty or damaged, writing or rewriting

errors may be noted - ensure that you check all discs for dirt or damage
before you use them.
■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or
DVD-RAM media will be affected by the quality of the disc itself and the
way in which it is used.
■ There are two types of DVD-R media available, authoring discs and
general use discs. Do not attempt to use authoring discs as only
general use discs can be written to by a computer drive.
■ You can use both DVD-RAM discs that can be removed from a cartridge
and DVD-RAM discs designed without a cartridge.
■ You may find that other computer DVD-ROM drives or other DVD
players may not be able to read DVD-R, DVD-R (Dual Layer),
DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW discs.
■ Data written to a CD-R, DVD-R, DVD-R (Dual Layer), DVD+R or
DVD+R (Double Layer) discs cannot be deleted either in whole or in
part.
■ Data deleted/erased from a CD-RW, DVD-RW, DVD+RW or DVD-RAM
disc cannot be recovered. You must check the content of the disc
carefully before you delete it, taking care that, if multiple drives that can
write data to discs are connected, you do not delete data from the
wrong one.
■ In writing to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R
(Double Layer), DVD+RW or DVD-RAM media, some space is required
for file management, so you may not be able to write to the full capacity
of the disc.

4-24 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ Since the disc is based on the DVD standard, it might be filled with
dummy data if the written data is less than about 1GB. Therefore, in
these circumstance, even if you write only a small amount of data, it
might take additional time to fill in the dummy data.
■ When multiple drives that can write data to discs are connected, be
sure that you do not write to or delete data from the wrong drive.
■ Be sure to connect the AC adaptor to the computer before you write or
rewrite any information.
■ Before you enter either Sleep Mode or Hibernation Mode, take care to
ensure that any DVD-RAM writing has been completed. In this instance,
writing is finished if you can eject the DVD-RAM media.
■ Be sure to close all other software programs except for the writing
software itself.
■ Do not run software such as a screen saver which can put a heavy load
on the processor.
■ Operate the computer at its full power settings - do not use any
power-saving features.
■ Do not write information while virus checking software is running,
instead wait for it to finish, then disable the virus protection applications,
including any software that checks files automatically in the
background.
■ Do not use any hard disk utilities, including those that are intended to
enhance hard disk drive access speeds, as they may cause unstable
operation and damage data.
■ CD-RW (Ultra Speed +) media should not be used as data may be lost
or damaged.
■ You should always write from the computer’s hard disk drive onto the
CD/DVD - do not try to write from shared devices such as a server or
any other network device.
■ Writing with software other than TOSHIBA Disc Creator has not been
confirmed, therefore operation with other software applications cannot
be guaranteed.

User’s Manual 4-25

TECRA A10/S10/M10/SatellitePro S300

When writing or rewriting

Please observe the following points while you write or rewrite data to CD-R,
CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double
Layer), DVD+RW or DVD-RAM media:
■ Always copy data from the hard disk drive to the optical media - do not
use the cut-and-paste function as the original data will be lost if there is
a write error.
■ Do not perform any of the following actions:
■ Change users in the Windows Vista operating system.
■ Operate the computer for any other function, including such tasks as
using a mouse or Touch Pad, or closing/opening the display panel.
■ Start a communication application such as a modem.
■ Apply impact or vibration to the computer.
■ Install, remove or connect external devices, including such items as
a PC Card, SD/SDHC memory card, miniSD/microSD Card, Smart
Card, Memory Stick/Memory Stick PRO/Memory Stick PRO Duo, xD
picture card, MultiMediaCard, USB device, external monitor, i.LINK
device, or an optical digital device.
■ Use the audio/video control button to reproduce music or voice.
■ Open the optical disc drive.
■ Do not use shut down, log off, Sleep Mode or Hibernation Mode
functions while writing or rewriting.
■ Make sure that the write/rewrite operation is completed before going
into either Sleep Mode or Hibernation Mode (writing is completed if you
can remove an optical media on the DVD Super Multi drive).
■ If the media is of poor quality, or is dirty or damaged, writing or rewriting
errors may occur.
■ Set the computer on a level surface and avoid places subject to
vibration such as airplanes, trains or cars. In addition, do not use the
computer on an unstable surface such as a stand.
■ Keep mobile phones and other wireless communication devices away
from the computer.

TOSHIBA Disc Creator

Please be aware of the following limitations when you use the TOSHIBA
Disc Creator:
■ DVD Video cannot be created using TOSHIBA Disc Creator.
■ DVD Audio cannot be created using TOSHIBA Disc Creator.
■ You cannot use TOSHIBA Disc Creator’s “Audio CD for Car or Home
CD Player” function to record music to DVD-R, DVD-R (Dual Layer),
DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media.
■ Do not use the “Disc Backup” function of TOSHIBA Disc Creator in
order to copy DVD Video or DVD-ROM material that has copyright
protection.

4-26 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ DVD-RAM discs cannot be backed up using the “Disc Backup” function

of TOSHIBA Disc Creator.
■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R,
DVD-R (Dual Layer) or DVD-RW media using the “Disc Backup”
function of TOSHIBA Disc Creator.
■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R,
DVD+R (Double Layer) or DVD+RW media using the “Disc Backup”
function of TOSHIBA Disc Creator.
■ You cannot back up DVD-ROM, DVD Video, DVD-R, DVD-R (Dual
Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW to
CD-R or CD-RW media using the “Disc Backup” function of TOSHIBA
Disc Creator.
■ TOSHIBA Disc Creator cannot record in packet format.
■ You might not be able to use the “Disc Backup” function of TOSHIBA
Disc Creator to back up a DVD-R, DVD-R (Dual Layer), DVD-RW,
DVD+R, DVD+R (Double Layer) or DVD+RW disc that was made with
other software on a different optical media recorder.
■ If you add data to a DVD-R, DVD-R (Dual Layer), DVD+R or DVD+R
(Double Layer) disc that you have already recorded to, you might not be
able to read the added data under some circumstances. For example, it
cannot be read under 16-bit operating systems, such as Windows 98SE
and Windows Me, while in Windows NT4 you will need Service Pack 6
or later, and in Windows 2000, you will need Service Pack 2. In addition
to this, some DVD-ROM and DVD-ROM / CD-R/RW drives cannot read
this added data regardless of the operating system.
■ TOSHIBA Disc Creator does not support recording to DVD-RAM discs -
to achieve this you should use Windows Explorer or another similar
utility.
■ When you back up a DVD disc, be sure that the source drive supports
recording to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R
(Double Layer) or DVD+RW media - if this is not the case then the
source disc might not be backed up correctly.
■ When you back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R,
DVD+R (Double Layer) or DVD+RW disc, be sure to use the same type
of disc.
■ You cannot partially delete any data written to a CD-RW, DVD-RW or
DVD+RW disc.

User’s Manual 4-27

TECRA A10/S10/M10/SatellitePro S300

Data Verification
To verify that data has been written or rewritten correctly to a data CD/DVD
you should follow the steps below before you begin the write/rewrite
process:
1. Display the setting dialog box by one of the following two steps:
■ Click the Recording settings button ( ) for writing on the main
toolbar in the Data Disc mode.
■ Select Settings for Each Mode -> Data Disc in the Settings menu.
2. Mark the Verify written data check box.
3. Select File Open or Full Compare mode.
4. Click the OK button.

How to learn more about TOSHIBA Disc Creator

Please refer to the Help files for additional TOSHIBA Disc Creator
information.

Media care
This section provides tips on protecting data stored on your CD’s, DVD’s
and floppy diskettes. Handle your media with care. Following the simple
precautions listed below will increase the lifetime of your media and protect
the data stored on it.

CD/DVDs
1. Store your CD’s and DVD’s in the containers they originally came in to
protect them and keep them clean.
2. Do not bend the CD’s or DVD’s.
3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD or DVD that contains the data.
4. Hold the CD or DVD by its outside edge or the edge on the center hole -
any fingerprints on the surface of the disc can prevent the drive from
properly reading data.
5. Do not expose the CD or DVD to direct sunlight, extreme heat or cold.
6. Do not place heavy objects on your CD’s or DVD’s.
7. If your CD’s or DVD’s become dusty or dirty, wipe them with a clean dry
cloth from the center hole outwards - do not wipe in a circular direction.
If necessary, you can use a cloth that has been lightly dampened in
water or a neutral cleaner but you must not use benzine, thinner or any
similar cleaning solution.

4-28 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Floppy diskettes

The USB floppy diskette drive is available only as an option.

1. Store your floppy diskettes in the container they came in to protect them
and keep them clean. If a floppy diskette becomes dirty, clean it with a
soft, lightly dampened cloth - do not use cleaning fluid.
2. Never open the shutter or touch the magnetic surface of your floppy
diskette - doing this could permanently damage it and lose data.
3. Always handle floppy diskettes with care to prevent the loss of stored
data.
4. Always apply the floppy diskette label in the correct location and never
apply a new label on top of an existing one - in this instance the label
could come loose and damage the floppy diskette drive.
5. Never use a pencil for writing on a floppy diskette label as the dust from
the pencil lead could cause a system malfunction if it found its way onto
the computer’s components. In this instance, always use a felt-tipped
pen and write the label first before applying it to the floppy diskette.
6. Never put a floppy diskette in a location where water or other liquid may
make contact with it, or where it is excessively damp - either of these
conditions could cause data loss.
7. Never use a wet or damp floppy diskette - this could damage the floppy
diskette drive or other devices within the computer.
8. Data may be lost if the floppy diskette is twisted, bent, or exposed to
direct sunlight, extreme heat or cold.
9. Do not place heavy objects on your floppy diskettes.
10. Do not eat, smoke, or use items such as erasers near your floppy
diskettes as foreign particles inside the jacket of the floppy diskette can
damage the magnetic surface.
11. Magnetic energy can destroy the data on your floppy diskettes. In view
of this you should keep your floppy diskettes away from speakers,
radios, televisions and other sources of magnetic fields.

Sound System
This section describes some of the audio control functions.

Volume Mixer
The Volume Mixer utility lets you control the audio volume for playback of
devices and applications under Windows.
■ To launch the Volume Mixer utility, right click on the speaker icon on the
Taskbar, and select Open Volume Mixer from the sub menu.
■ To adjust the volume level of speakers or headphones, move the
Speakers slider.
■ To adjust the volume level of an application that you are using, move
the slider for the corresponding application.

User’s Manual 4-29

TECRA A10/S10/M10/SatellitePro S300

Microphone Level
Follow the steps below to change the microphone recording level.
1. Right click on the speaker icon on the Taskbar, and select Recording
Devices from the sub menu.
2. Select Microphone, and click Properties.
3. On the Levels tab move the Microphone slider to increase or decrease
the microphone volume level.
If you feel the microphone volume level is inadequate, move the
Microphone Boost slider to a higher level.

PC Beep Level
Follow the steps below to change the PC Beep playback level.
1. Right click on the speaker icon on the Taskbar, and select Playback
Devices in the sub menu.
2. Select Speakers, and click Properties.
3. On the Levels tab move the PC Beep slider to increase or decrease the
PC Beep volume level.

Audio Enhancements
In order to apply the sound effects for your current speaker, follow the steps
below.
1. Right click on the speaker icon on the Taskbar, and select Playback
Devices from the sub menu.
2. Select Speakers, and click Properties.
3. On the Enhancements tab select the sound effects you would like, and
click Apply.

Realtek HD Audio Manager

You can confirm and change the audio configuration using the Realtek
Audio Manager. To launch the Realtek Audio Manager, click Start ->
Control Panel -> Hardware and Sound -> Realtek HD Audio Manager.
When you first launch the Realtek Audio Manager, you will see two device
tabs. Speakers is the default output device. Microphone is the default
input device. To change the default device, click the Set Default Device
button under the chosen device tab.

Information
Click the information button to view hardware information, software
information, and language setting.

4-30 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Power Management
The audio controller in your computer can be turned off when the audio
function is not used. To adjust the configuration of audio power
management, click the battery button .
■ When audio power management is enabled, the circle button at the
upper left of the Power Management is blue and convex.
■ When audio power management is disabled, the button is black and
concave.

Speaker Configuration
Click the Auto Test button to confirm the internal speakers or the
headphone sound is coming from the right direction.

Default Format
You can change the sample rate and bit depth of sound.

Modem
This section describes how to connect and disconnect the internal modem
to and from a telephone jack.
■ Connection to any communication line other than an analog phone line
could cause a computer system failure.
■ Connect the built-in modem only to ordinary analog phone lines.
■ Never connect the built-in modem to a digital line (ISDN).
■ Never connect the built-in modem to the digital connector on a
public telephone or to a digital private branch exchange (PBX).
■ Never connect the built-in modem to a key telephone system for
residences or offices.
■ Avoid using your computer modem with the telephone cable connected
during an electrical storm. There may be a remote risk of electric shock
from lightning.

Modem functions cannot be used in models which are not equipped with a
modem.

Region selection
Telecommunication regulations vary from one region to another, so you will
need to make sure the internal modem’s settings are correct for the region
in which it will be used.
The built-in modem can be used only in specified countries and regions.
Using the modem in an area not specified for use may cause a system
failure. Check the specified areas carefully before using it.

User’s Manual 4-31

TECRA A10/S10/M10/SatellitePro S300

To select a region, follow the steps as detailed below:

1. Click Start -> All Programs -> TOSHIBA -> Networking -> Modem
Region Select.
If it is available, do not use the Country/Region Select function included as
part of the modem setup utility within the Control Panel - if you change the
country/region setting this way you may find that the change does not take
effect.

2. The Region Selection icon will appear in the Windows Taskbar.

3. Click the icon with the primary (left) mouse button to display a list of
regions that the modem supports, together with a sub-menu which
details telephony location information - a check mark will appear next to
the currently selected region and telephony location.
4. Select either a region from the region menu or a telephony location from
the sub-menu.
■ When you click a region it becomes the modem’s default selection
for any new dialling locations that are created within the Windows
Control Panel (Phone and Modem Options).
■ When you select a telephony location, the corresponding region is
automatically selected and becomes the modem’s default setting.

Properties menu
Click the icon with the secondary (right) mouse button in order to display a
Properties menu on the screen.

Setting
Within the Properties menu you are able to either enable or disable the
following settings:

AutoRun Mode
Allows you to configure whether the Modem Region Select utility starts
automatically whenever you start up the operating system.

Open the Dialing Properties dialog box after selecting region

Allows you to configure whether the dialing properties dialog box will be
displayed automatically after you have selected a region.

Location list for region selection.

Displays a sub-menu appears which details location information.

Open dialog box, if the modem and Telephony Current

Location region code do not match.
Displays a warning if the current settings for both region code and
telephony location are different.

4-32 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Modem Selection
If the computer cannot recognize the internal modem, a dialog box is
displayed from which you should select the appropriate communications
port for your modem to use.

Dialing Properties
You should select this item in order to display the dialing properties.
If you are using the computer in Japan, the Telecommunications Business
Law requires that you select Japan region mode. It is illegal to use the
modem in Japan with any other selection.

Connecting the modular cable

To connect the modem’s modular cable, follow the steps as detailed below:
■ Connection to any communication line other than an analog phone line
could cause a computer system failure.
■ Connect the built-in modem only to ordinary analog phone lines.
■ Never connect the built-in modem to a digital line (ISDN).
■ Never connect the built-in modem to the digital connector on a
public telephone or to a digital private branch exchange (PBX).
■ Never connect the built-in modem to a key telephone system for
residences or offices.
■ Avoid using your computer modem with the telephone cable connected
during an electrical storm. There may be a remote risk of electric shock
from lightning.
1. Plug the end of the modular cable into the computer’s modem jack.
2. Plug the other end of the modular cable into a telephone jack.
Telephone jack

Modem jack
Modular cable

Figure 4-10 Connecting the internal modem

Do not pull on the cable or move the computer while the cable is
connected.

User’s Manual 4-33

TECRA A10/S10/M10/SatellitePro S300

If you use a storage device such as an optical disc drive or hard disk drive
connected to a 16-bit PC Card, you might experience the following
problems with the operation of the modem:
■ The modem speed is slow or communication is periodically interrupted.
■ Skips or jumps may be noted in sound.

Disconnecting the modular cable

To disconnect the modular cable, follow the steps as detailed below:
1. Pinch the lever on the plug in the telephone jack and pull it out from
within the connector.
2. Pinch the lever on the plug in the computer’s modem jack and pull it out
from within the computer.

Wireless communications
The computer’s wireless communication function supports some wireless
communication devices.
Only some models are equipped with both Wireless LAN and Bluetooth
functions.
■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a
microwave oven or in areas subject to radio interference or magnetic
fields. Interference from a microwave oven or other source can disrupt
Wi-Fi or Bluetooth operation.
■ Turn all wireless functionalities off when near a person who may have a
cardiac pacemaker implant or other medical electric device. Radio
waves may affect pacemaker or medical device operation, possibly
resulting in serious injury. Follow the instruction of your medical device
when using any wireless functionality.
■ Always turn off wireless functionality if the computer is near automatic
control equipment or appliances such as automatic doors or fire
detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.
■ It may not be possible to make a network connection to a specified
network name using the ad hoc network function.
If this occurs, the new network(*) will have to be configured for all
computers connected to the same network in order to re-enable
network connections.
* Please be sure to use new network name.

4-34 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Wireless LAN
The Wireless LAN is compatible with other LAN systems based on Direct
Sequence Spread Spectrum / Orthogonal Frequency Division Multiplexing
radio technology that complies with the IEEE802.11 Wireless LAN standard.
■ Frequency Channel Selection of 5GHz for IEEE 802.11a or/and
IEEE802.11n draft 2.0
■ Frequency Channel Selection of 2.4GHz for IEEE 802.11b/g or/and
IEEE802.11n draft 2.0
■ Roaming over multiple channels
■ Card power management
■ Wired Equivalent Privacy (WEP) data encryption based on an 128-bit
encryption algorithm
■ Wi-Fi Protected Access™ (WPA™)
The transmission speed over the wireless LAN, and the distance over
which the wireless LAN can reach, may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, client design and software/hardware configurations. The
transmission rate described is the theoretical maximum speed as specified
under the appropriate standard - the actual transmission speed will be
lower than the theoretical maximum speed.

Setting
1. Please make sure that the Wireless Communication Switch is
turned on.
2. Click Start and then click Connect To to display Connect to a network
window.
3. Click Set up a connection or network.
4. Follow the wizard. You will need the name of the wireless network
together with security settings. Consult the documentation
accompanied with your router or ask your wireless network
administrator for the settings.

Security
■ TOSHIBA strongly recommend that you enable encryption functionality,
otherwise your computer will be open to illegal access by an outsider
using a wireless connection. If this occurs, the outsider may illegally
access your system, eavesdrop, or cause the loss or destruction of
stored data.
■ TOSHIBA is not liable for the loss of data due to eavesdropping or
illegal access through the wireless LAN and the damage thereof.

User’s Manual 4-35

TECRA A10/S10/M10/SatellitePro S300

Bluetooth wireless technology

Bluetooth wireless technology eliminates the need for cables, such as
desktop computers, between your PC and other electronic devices,
example of printers and mobile phones.
You cannot use the computer’s built-in Bluetooth functions and an external
Bluetooth adaptor simultaneously. For reference, Bluetooth wireless
technology has the following features:

Worldwide operation
The Bluetooth radio transmitter and receiver operate in the 2.4GHz band,
which is license-free and compatible with radio systems in most countries
in the world.

Radio links
You can easily establish links between two or more devices, with these
links being maintained even if the devices are not within a line-of-sight of
each other.

Security
Two advanced security mechanisms ensure a high level of security:
■ Authentication prevents access to critical data and makes it impossible
to falsify the origin of a message.
■ Encryption prevents eavesdropping and maintains link privacy.

Bluetooth Stack for Windows by TOSHIBA

Please note that this software is specifically designed for the following
operating systems:
■ Microsoft Windows Vista
Information regarding the use of this software with these operating systems
is listed below, with further details being contained with the electronic help
files supplied with the software.
This Bluetooth Stack is based on the Bluetooth Version 1.1/1.2/2.0+EDR/
2.1+EDR specification. However, TOSHIBA cannot confirm the
compatibility between any computing products and/or other electronic
devices that use Bluetooth, other than TOSHIBA notebook computers.

Release Notes related to the Bluetooth Stack for Windows

by TOSHIBA
1. Fax application software:
Please be aware that there is some fax application software that you
cannot use on this Bluetooth Stack.
2. Multi-user considerations:
On Windows Vista, the use of Bluetooth is not supported in a multi-user
environment. This means that, when you use Bluetooth, other users
that are logged into the same computer will not be able to use this type
of functionality.

4-36 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Product Support:
The latest information regarding operating system support, language
support or available upgrades can be found on our web site
http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or
http:://www.pcsupport.toshiba.com in the United States.

Wireless communication switch

You can enable or disable Wireless communication functions, with the
on/off switch. No transmissions are sent or received when the switch is off.
Slide the switch forward to turn it on and backward to turn it off.

Wireless communication Indicator

The wireless communication indicator shows the status of the computer’s
wireless communication functions.

Indicator status Indication

Indicator off The wireless communication switch is off -
no wireless functionality is available.
Indicator glows Wireless communication switch is on. Except for
the stopped device by the software switch, all
the wireless-communications functions can
output a radio wave.
If you used the Taskbar to disable the wireless LAN, restart the computer or
perform the following procedure to re-enable it: Start -> Control Panel ->
System and Maintenance -> System -> Device Manager -> Network
adapters and right click the wireless device then choose enable.

LAN
The computer has built-in support for Ethernet LAN (10 megabits per
second, 10BASE-T), Fast Ethernet LAN (100 megabits per second,
100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second,
1000BASE-T).
This section describes how to connect/disconnect to a LAN.
Do not install or remove a memory module while Wake-up on LAN is
enabled.

■ The Wake-up on LAN function consumes power even when the system
is off. Leave the AC adaptor connected while using this feature.
■ The Link speed (10/100/1000 megabits per second) changes
automatically depending on the network conditions (connected device,
cable or noise and so on).

User’s Manual 4-37

TECRA A10/S10/M10/SatellitePro S300

LAN cable types

The computer must be configured properly before connecting to a LAN.

Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.

If you are using Gigabit Ethernet LAN (1000 megabits per second,
1000BASE-T), be sure to connect with a CAT5E cable or higher.
You cannot use a CAT3 or CAT5 cable.
If you are using Fast Ethernet LAN (100 megabits per second,
100BASE-TX), be sure to connect with a CAT5 cable or higher.
You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you
can connect with a CAT3 or higher cable.

Connecting the LAN cable

To connect the LAN cable, follow the steps as detailed below:
■ Connect the AC adaptor before connecting the LAN cable. The AC
adaptor must remain connected during LAN use. If you disconnect the
AC Adaptor while the computer is accessing a LAN, the system may
hang up.
■ Do not connect any other cable to the LAN jack except the LAN cable.
Otherwise, malfunctions or damage may occur.
■ Do not connect any power supplying device to the LAN cable that is
connected to the LAN jack. Otherwise, malfunctions or damage may
occur.

1. Turn off the power to the computer and to all external devices
connected to the computer.
2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.

LAN cable

LAN jack

Figure 4-11 Connecting the LAN cable

3. Plug the other end of the cable into a LAN hub connector or router.
Check with your LAN administrator and hardware or software vendor
before using or configuring a network connection.

4-38 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

When the computer is exchanging data with the LAN, the LAN Active
indicator glows orange. When the computer is connected to a LAN hub but
is not exchanging data, the Link indicator glows green.

Disconnecting the LAN cable

To disconnect the LAN cable, follow the steps as detailed below:
Make sure the LAN Active indicator (orange LED) is out before you
disconnect the computer from the LAN.

1. Pinch the lever on the connector in the computer’s LAN jack and pull
out the connector.
2. Disconnect the cable from the LAN hub or router in the same manner.
Check with your LAN administrator and hardware or software vendor
before disconnecting from the hub.

Computer Handling
This section explains computer handling and maintenance.

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust
and dirt, and use care with all liquids around it.
■ Be careful not to spill liquids into the computer. If the computer does get
wet, turn the power off immediately and let the computer dry completely
- in these circumstance you should get the computer inspected by an
authorized service provider in order to assess the scope of any
damage.
■ Clean the plastics of the computer using a slightly water dampened
cloth.
■ You can clean the display screen by spraying a small amount of glass
cleaner onto a soft, clean cloth and then wiping the screen gently with
the cloth.
Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.

User’s Manual 4-39

TECRA A10/S10/M10/SatellitePro S300

Moving the computer

While the computer is designed for rugged durability you should exercise a
few simple precautions when moving it in order to help ensure trouble-free
operation.
■ Before moving the computer, it is recommended that you change the
setting associated with the Hard Disk Drive Protection feature. Please
refer to the section, Using the Hard Disk Drive (HDD) Protection, in this
chapter for further information.
■ Make sure all disk/disc activity has ended before moving the computer -
check that the HDD and other indicators on the front of the computer
are off.
■ Turn off (shut down) the computer.
■ Disconnect the AC adaptor and all peripherals before moving the
computer.
■ Close the display panel.
■ Do not pick up the computer by its display panel.
■ Before carrying your computer, shut it down, disconnect the AC adaptor
and allow it to cool down - a failure to follow this instruction may result in
minor heat injury.
■ Be careful not to subject the computer to impact or shock - a failure to
follow this instruction could result in damage to computer, computer
failure or loss of data.
■ Never transport your computer with any cards installed - this may cause
damage to either the computer and/or the card resulting in product
failure.
■ Always use a suitable carry case when transporting the computer.
■ When carrying your computer, be sure to hold it securely so that it does
not fall or hit anything.
■ Do not carry your computer by holding any of its protruding elements.

4-40 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Using the Hard Disk Drive (HDD) Protection

This computer has a function for reducing the risk of damage on the hard
disk drive.
Using an acceleration sensor built into the computer, TOSHIBA HDD
Protection detects vibration shocks and similar signs of movement of the
computer, and automatically moves the Hard Disk Drive head to a safe
position to reduce the risk of damage that could be caused by head-to-disk
contact.
■ The TOSHIBA HDD Protection function does not guarantee that the
hard disk drive will not be damaged.
■ TOSHIBA HDD Protection cannot be used in models that are equipped
with SSD.
When vibration is detected, a message will be displayed on the screen, and
the icon in the Taskbar notification area will change to the protection state.
This message is displayed until the OK button is pressed or 30 seconds
pass. When vibration subsides, the icon returns to the normal state.

Taskbar icon
State Icon Description
Normal TOSHIBA HDD Protection is enabled.

Protection TOSHIBA HDD Protection is active. The

hard disk drive head is in a safe position.
OFF TOSHIBA HDD Protection is disabled.

TOSHIBA HDD Protection Properties

You can change the TOSHIBA HDD Protection settings by using the
TOSHIBA HDD Protection Properties window. To open the window, click
Start -> All Programs -> TOSHIBA -> Utilities -> HDD Protection
Settings. The window can also be started from the icon on the Taskbar or
from the Control Panel.

HDD Protection
You can choose whether to enable or disable TOSHIBA HDD Protection.

User’s Manual 4-41

TECRA A10/S10/M10/SatellitePro S300

Detection Level
This function can be set to four levels. The sensitivity levels in which
vibrations, impacts and their similar signs are detected can be set to OFF,
1, 2 and 3 in ascending order. Level 3 is recommended for better protection
of the computer. However, when the computer is used in a mobile
environment or in other unstable conditions, setting the detection level to 3
could result in frequent execution of TOSHIBA HDD Protection, which will
slow Hard Disk Drive reading and writing. Set a lower detection level when
the speed of Hard Disk Drive reading and writing is a priority.
Different detection levels can be set depending on whether the computer is
used as handheld or mobile usages, or whether it is used in a stable
environment such as on a table in the workplace or at home. By setting
different detection levels for the computer depending on whether it runs
with the AC power (desktop) or with batteries (handheld or mobile usage),
the detection level automatically switches according to the power
connection mode.

3D Viewer
This feature displays a 3D object on the screen which moves in according
to tilting or vibration of the computer.
When the TOSHIBA HDD Protection detects computer vibration the Hard
Disk Drive head is parked and the 3D object disk rotation will stop. When
the head is un-parked the disk will begin to rotate again.
The 3D Viewer can be started from the icon in the task tray.
■ This 3D object virtually represents the Computer’s internal Hard Disk
Drive. This representation may vary from the actual number of disks,
disk rotation, head movement, part size, shape and direction.
■ This feature may use a large amount of CPU and memory on some
models. The computer may become slow or sluggish when attempting
to run other applications while the 3D Viewer is displayed.
■ Intensely shaking the computer or other subjecting it to strong impacts
may cause damage to the computer.

4-42 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Details
To open the Details window, click the Setup Detail button in the TOSHIBA
HDD Protection Properties window.

Detection Level Amplification

When the AC adaptor is disconnected or the lid is closed, HDD Detection
assumes that the computer will be carried and sets the detection level to
the maximum for 10 seconds.
TOSHIBA HDD Protection Message
Specify whether to display a message when TOSHIBA HDD Protection is
active.
This function does not work when the computer is booting, in Sleep Mode,
in Hibernation Mode, in transition to Hibernation Mode, recovering from
Hibernation Mode, or powered off. Do not subject the computer to vibration
or impact while the function is disabled.

Using the TOSHIBA USB Sleep and Charge Utility

This utility displays whether the USB Sleep and Charge function is enabled
or disabled and shows the positions of USB ports that support the USB
Sleep and Charge function. It also displays the remaining battery capacity.

USB Sleep and Charge

Your computer can supply USB bus power (DC5V) to the USB port even
when the power of the computer is turned OFF. “Power OFF” includes
Sleep Mode, Hibernation Mode or shutdown state.
This function can be used for ports that support the USB Sleep and Charge
function (hereinafter called “compatible ports”).
Compatible ports are USB ports that have the ( ) symbol icon.
You can use the “USB Sleep and Charge function” to charge certain
USB-compatible external devices such as mobile phones or portable digital
music players.
However, the “USB Sleep and Charge function” may not work with certain
external devices even if they are compliant with the USB specification.
In those cases, turn the power of the computer ON to charge the device.

User’s Manual 4-43

TECRA A10/S10/M10/SatellitePro S300

■ When “USB Sleep and Charge function” is set to [Enabled], USB bus
power (DC5V) will be supplied to compatible ports even when the
power of the computer is turned OFF.
USB bus power (DC5V) is similarly supplied to the external devices
which are connected to the compatible ports. However, some external
devices cannot be charged solely by supplying USB bus power
(DC5V).
As for the specifications of the external devices, please contact the
device manufacturer or check the specifications of the external devices
thoroughly before use.
■ Using the USB sleep and charge function to charge external devices
will take longer than charging the devices with their own chargers.
■ If external devices are connected to compatible ports when the AC
adaptor is not connected to the computer, the battery of the computer
will be depleted even when the power of the computer is turned OFF.
As such, we recommend that you connect the AC adaptor to the
computer when using the USB sleep and charge function.
■ External devices connected to the USB bus power (DC5V) function that
interfaces with the power ON/OFF of the computer may always be in
an operational state.
■ When there is a current overflow of the external devices connected to
the compatible ports, USB bus power (DC5V) supply may be stopped
for safety reasons.
■ When “USB Sleep and Charge function” is set to [Enabled], the “USB
Wakeup function” does not work for compatible ports.
In that case, if there is a USB port that does not have the USB Sleep
and Charge function-compatible icon ( ), attach the mouse or
keyboard to it.
If all USB ports have the USB Sleep and Charge function-compatible
icon ( ), change the “USB Sleep and Charge function” setting to
[Disabled].
The “USB Wakeup function” will now work, but the “USB Sleep and
Charge function” will be disabled.

Metal paper clips or hair pins/clips will generate heat if they come into
contact with USB ports. Do not allow USB ports to come into contact with
metal products, for example when carrying the computer in your bag.

Starting the USB Sleep and Charge Utility

To start the utility, click Start-> All Programs -> TOSHIBA -> Utilities ->
USB Sleep and Charge.

4-44 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Enabling USB Sleep and Charge

This utility can be used to enable and disable the USB Sleep and Charge
function in groups. USB Sleep and Charge compatible USB ports are
assigned to each group.
Check the check boxes for each group to enable the USB Sleep and
Charge function for the USB ports assigned to that group. In the default
state all groups are disabled.

Power supply mode settings

There are several USB Sleep and Charge function modes.
“Mode 1” should normally be used. Set one of the other modes if the
charge function cannot be used in “Mode 1”. The selected charge mode will
be applied to all groups.
Some groups may be grayed out and not able to be selected for some
modes. This indicates that those groups are not compatible with the
selected mode and the USB Sleep and Charge function cannot be used.
In this situation, either select a different mode, or set one of the selectable
“Groups”. This function may not be able to be used with some connected
external devices even if the appropriate group is selected. In this situation,
uncheck the check boxes for each group and stop using this function.

Battery Settings
This utility can be used to specify the lower limit of remaining battery life for
USB Sleep and Charge. Move the slider bar to specify the lower limit. If the
remaining battery life falls below the setting, the USB Sleep and Charge
function will be stopped. Checking the “AC Only” check box sets the utility
to only charge when the AC adaptor is connected.

Heat dispersal
To protect against overheating, the processor is equipped with an internal
temperature sensor which activates a cooling fan or lowers the processing
speed if the computer’s internal temperature rises to a certain level. You
are able to select whether to control this temperature by either turning on
the fan first, then if necessary lowering the processor speed, or by lowering
the processor speed first, then if necessary turning on the fan. Both of
these functions are controlled through the Power Options.
When the processor’s temperature falls within normal range, the fan will be
turned off and the processor operation returned to its standard speed.
If the processor’s temperature reaches an unacceptably high level with
either setting, the computer automatically shuts down to prevent any
damage. In this instance all unsaved data in memory will be lost.

User’s Manual 4-45

TECRA A10/S10/M10/SatellitePro S300

4-46 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 5

The Keyboard

The computer’s keyboard layouts are compatible with a 104/105-key

enhanced keyboard - by pressing some keys in combination, all of the
104/105-key enhanced keyboard functions can be performed on the
computer.
The number of keys available on your keyboard will depend on which
country/region your computer is configured for, with keyboards being
available for numerous languages.
In use there are six different types of keys, specifically typewriter keys,
function keys, soft keys, Hot keys, Windows special keys and the keypad
overlay.

Typewriter keys
The typewriter keys produce the upper-case and lower-case letters,
numbers, punctuation marks, and special symbols that appear on the
screen. However, there are some differences between using a typewriter
and using a computer keyboard:
■ Letters and numbers produced in computer text vary in width. Spaces,
which are created by a “space character” may also vary depending on
line justification and other factors.
■ The lowercase l (el) and the number 1 (one), together with the
uppercase O (oh) and the 0 (zero), are not interchangeable on
computers as they are on a typewriter.
■ The CAPS LOCK function key locks only the alphabetic characters into
upper-case while the Shift Lock function on a typewriter places all keys
in the shifted position.
■ The SHIFT keys, the Tab key, and the BACK SPACE key perform the
same function as their typewriter counterparts but also have special
computer functions.
Never remove the key caps on your keyboard. Doing so could cause
damage to the parts under the key caps.

User’s Manual 5-1

TECRA A10/S10/M10/SatellitePro S300

Function keys: F1 … F12

The function keys (not to be confused with the special FN key) are the
twelve keys at the top of your keyboard - these keys function differently
from other keys.

F1 through F12 are called function keys because they execute

programmed functions when pressed and, when used in combination with
the FN key, those keys marked with icons also execute specific functions
on the computer. Please refer to the section, Soft keys: FN key
combinations, in this chapter for further information, taking care to note that
the function executed by individual keys will depend on the software you
are using.

Soft keys: FN key combinations

The FN (function) is unique to TOSHIBA computers and is used in
combination with other keys to form soft keys. Soft keys are key
combinations that enable, disable or configure specific features.
Please note that some software may disable or interfere with soft-key
operations, and that the soft-key settings are not restored when the
computer returns from Sleep Mode.

Emulating keys on an enhanced keyboard

Figure 5-1 A 104-key enhanced keyboard layout

This computer’s keyboard is designed to provide all the features of the

104/105-key enhanced keyboard.
Since the keyboard is smaller and has fewer keys, some of the enhanced
keyboard functions must be simulated using two keys instead of one on the
larger keyboard.
The FN key can be combined with the following keys to simulate functions
similar to those of keys on the 104/105-key enhanced keyboard which are
not on this computer’s keyboard.

5-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Press FN + F10 or FN + F11 to access the computer’s integrated keypad.

When activated, the keys with grey markings on their bottom edge become
either numeric keypad keys (FN + F11) or cursor control keys (FN + F10).
Please refer to the Keypad overlay section in this chapter for more
information on how to operate these keys, taking care to note that the
power on default for both settings is off.

Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power
on default is off.

Press FN + ENTER to simulate ENTER on the enhanced keyboard’s

numeric keypad.

Hot keys
Hot keys (pressing FN + a function or ESC key) let you enable or disable
certain features of the computer.

Mute: Pressing FN + ESC turns the volume on and off.

Lock: Pressing FN + F1 enters “Lock computer mode”. To restore your

desktop, you need to log on again.

Power Plan: Pressing FN + F2 changes the power settings.

User’s Manual 5-3

TECRA A10/S10/M10/SatellitePro S300

Sleep: Pressing FN + F3 switches the system to Sleep Mode.

Hibernate: Pressing FN + F4 switches the system to Hibernation Mode.

Output: Pressing FN + F5 changes the active display device.

To use a simultaneous mode, you must set the resolution of the internal
display panel to match the resolution of the external display device.

Brightness Down: Pressing FN + F6 decreases the computer’s display

panel brightness in individual steps.

Brightness Up: Pressing FN + F7 increases the computer’s display panel

brightness in individual steps.

Wireless: Pressing FN + F8 switches the active wireless devices if the

wireless communication switch is switched on.
If no wireless communication device is installed, no dialog box will appear.

Touch Pad: Pressing FN + F9 enables or disables the Touch Pad and

AccuPoint function.

5-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Zoom: Pressing FN + Space changes the display resolution.

TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon

size on the desktop or the font sizes within one of the supported application
windows.

TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon

size on the desktop or the font sizes within one of the supported application
windows.

FN Sticky key
You can use the TOSHIBA Accessibility Utility to make the FN key sticky,
that is, you can press it once, release it, and then press an “F Number” key.
To start the TOSHIBA Accessibility utility, click Start -> All Programs ->
TOSHIBA -> Utilities -> Accessibility.

Windows special keys

The keyboard provides two keys that have special functions in Windows,
the Windows Start Button key activates the Start menu while the
application key has the same function as the secondary (right) mouse
button.

This key activates the Windows Start menu.

This key has the same function as the secondary (right) mouse button.

User’s Manual 5-5

TECRA A10/S10/M10/SatellitePro S300

Keypad overlay
Your computer’s keyboard does not have a separate numeric keypad but
includes a numeric keypad overlay which functions like one - this is located
in the center of the keyboard with the relevant keys having grey letters at
their front edge. The overlay provides the same functions as the numeric
keypad on a standard 104/105-key enhanced keyboard.

Turning on the overlays

The numeric keypad overlay can be used for numeric data input or cursor
and page control.

Arrow Mode
To turn on Arrow Mode, press FN + F10 - the Arrow Mode indicator lights
and you are able to access cursor and page control functions by using the
keys. You are able to press FN + F10 again to turn off this overlay function.

Numeric Mode
To turn on Numeric Mode, press FN + F11 - the Numeric Mode indicator
lights and you are able to access numeric characters by using the keys.
You are able to press FN + F11 again to turn off this overlay function.

Figure 5-2 The numeric keypad overlay

5-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Temporarily using normal keyboard (overlay on)

While using the overlay, you can temporarily access the normal keyboard
functions without having to turn the overlay off:
1. Hold down FN key and press any other key - this key will operate as if
the overlay were off.
2. Type upper-case characters by holding down FN + SHIFT and pressing
a character key.
3. Release FN key to continue using the selected overlay function.

Temporarily using overlay (overlay off)

While using the normal keyboard function, you can temporarily use the
keypad overlay without having to turn it on:
1. Hold down FN key.
2. Check the keyboard indicators as pressing the FN key will turn on the
most recently used overlay function - if the Numeric Mode indicator
lights you can use the overlay for numeric entry, while if the Arrow Mode
indicator lights, you can use the overlay for cursor and page control
function.
3. Release FN key to return to normal keyboard operation.

Temporarily changing modes

If the computer is in Numeric Mode, you can switch temporarily to Arrow
Mode by pressing a SHIFT key, while if it is in Arrow Mode, you can switch
temporarily to Numeric Mode by also pressing a SHIFT key.

Generating ASCII characters

Not all ASCII characters can be generated using normal keyboard
operation, but you are able to generate these characters using their specific
ASCII codes.
With the overlay on:
1. Hold down ALT key.
2. Using the overlay keys, type the ASCII code of the character you
require.
3. Release ALT - the ASCII character will appear on the display screen.
With the overlay off:
1. Hold down ALT + FN.
2. Using the overlay keys, type the ASCII code of the character you
require.
3. Release ALT + FN - the ASCII character will appear on the display
screen.

User’s Manual 5-7

TECRA A10/S10/M10/SatellitePro S300

5-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 6

Power and Power-Up Modes

The computer’s power resources include the AC adaptor, battery pack and
any internal batteries. This chapter provides details on making the most
effective use of these resources, and includes information on charging and
changing batteries, tips for saving battery power, and information on the
different power-up modes.

Power conditions
The computer’s operating capability and battery charge status are affected
by different power conditions, including whether an AC adaptor is
connected, whether a battery pack is installed and what the charge level is
for that battery.
Table 6-1 Power conditions

Power on Power off

(no operation)

AC adaptor Battery fully • Operates • No charge

connected charged • No charge • LED: Battery green
• LED: Battery green DC IN green
DC IN green

Battery partially • Operates • Quick charge

charged or no • Charge • LED: Battery orange
charge
• LED: Battery orange DC IN green
DC IN green
No battery • Operates • No charge
installed • No charge • LED: Battery off
• LED: Battery off DC IN green
DC IN green

User’s Manual 6-1

TECRA A10/S10/M10/SatellitePro S300

Table 6-1 Power conditions continued

Power on Power off

(no operation)

AC adaptor Battery charge is • Operates

not above low battery • LED: Battery off
connected trigger point DC IN off

Battery charge is • Operates

below low battery • LED: Battery
trigger point flashes orange
DC IN off
Battery charge is Computer shuts down
exhausted
No battery • No operation
installed • LED: Battery off
DC IN off

Monitoring of power condition

As shown in the below table, the Battery, DC IN and Power indicators on
the system indicator alert you to the computer’s operating capability and
battery charge status.

Battery indicator
Check the Battery indicator to determine the status of the battery pack.
The following indicator lights indicate the battery status:
Flashing orange The battery charge is low, the AC adaptor must be
connected in order to recharge the battery.
Orange Indicates the AC adaptor is connected and the
battery is charging.
Green Indicates the AC adaptor is connected and the
battery is fully charged.
No light Under any other conditions, the indicator does not
light.

If the battery pack becomes too hot while it is being charged, the charge
will stop and the Battery indicator will go out. When the battery pack’s
temperature falls to a normal range, charging will resume - this process will
occur regardless of whether the computer’s power is on or off.

6-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

DC IN indicator
Check the DC IN indicator to determine the power status with the AC
adaptor connected - the following indicator conditions should be noted:

Green Indicates the AC adaptor is connected and is

correctly supplying power to the computer.
Flashing orange Indicates a problem with the power supply. You
should initially try plugging the AC adaptor into
another power outlet - if it still does not operate
properly, you should contact your reseller or dealer.
No light Under any other conditions, the indicator does
not light.

Power indicator
Check the Power indicator to determine the power status of the computer -
the following indicator conditions should be noted:
Green Indicates power is being supplied to the computer
and the computer is turned on.
Blinking orange Indicates that the computer is in Sleep Mode and
that there is sufficient power available (AC adaptor
or battery) to maintain this condition. In Sleep Mode,
this indicator will turn on for one second and off for
two seconds.
No light Under any other conditions, the indicator does
not light.

Battery
This section explains battery types, use, recharging methods and handling.

Battery types
The computer has four different types of batteries.

Battery pack
When the AC adaptor is not connected, the computer’s main power source
is a removable lithium ion battery pack, also referred to in this manual as
the main battery. You can purchase additional battery packs for extended
use of the computer away from an AC power source although you should
not change the battery pack while the AC adaptor is connected.
Before you remove the battery pack, save your data and shut down the
computer, or place the computer into Hibernation Mode. Please be aware
that, when placing the computer into Hibernation Mode, the contents of
memory will be saved to the hard disk drive, although for safety sake, it is
best to also save your data manually.

User’s Manual 6-3

TECRA A10/S10/M10/SatellitePro S300

Extended Capacity Battery Pack (Included with some

models, or option)
The Extended Capacity Battery Pack is included with some models, or can
be purchased separately as an optional accessory.

High Capacity Battery Pack (Included with some models, or

option)
The High Capacity Battery Pack is included with some models, or can be
purchased separately as an optional accessory.

Real Time Clock (RTC) battery

The Real Time Clock (RTC) battery provides power for the internal real
time clock and calendar function and also maintains the system
configuration while the computer is turned off. If the RTC battery becomes
completely discharged, the system will lose this information and the real
time clock and calendar will stop working - in this instance the following
message will be displayed when you turn on the power:
S **** RTC battery is low or CMOS checksum is
inconsistent ****
Press [F1] key to set Date/Time.

You can change the Real Time Clock settings by turning the computer on
while pressing the ESC key and then the F1 key when prompted. Please
refer to Chapter 8, Troubleshooting, for further information.
The RTC battery does not charge while the computer is turned off even if
the AC adaptor is attached.

Care and use of the battery pack

This section provides the important safety precautions in order to handle
your battery pack properly.
Refer to the enclosed Instruction Manual for Safety and Comfort for
detailed precautions and handling instructions.
■ Make sure the battery is securely installed in the computer before
attempting to charge the battery pack. Improper installation could
generate smoke or fire, or cause the battery pack to rupture.
■ Keep the battery pack out of reach of infants and children. It can cause
injury.

6-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ The battery pack, Extended Battery Pack and High Capacity Battery
Pack are lithium ion batteries, which can explode if not replaced, used,
handled or disposed of properly. Dispose of the battery as required by
local ordinances or regulations. Use only batteries recommended by
TOSHIBA as replacements.
■ The computer’s RTC battery is a Ni-MH battery and should be replaced
only by your dealer or by a TOSHIBA service representative. The
battery can explode if not properly replaced, used, handled or
disposed. Dispose of the battery as required by local ordinances or
regulations.
■ Charge the battery pack only in an ambient temperature between 5 and
35 degrees Celsius. Otherwise, the electrolyte solution might leak,
battery pack performance might deteriorate and the battery life might
be shortened.
■ Never install or remove the battery pack without first turning off the
power and disconnecting the AC adaptor. Never remove the battery
pack while the computer is in Sleep Mode. Data could be lost.
■ When the High Capacity Battery Pack is connected to the computer, do
not hold on only to the High Capacity Battery Pack when lifting the
computer up. The High Capacity Battery Pack may separate from the
computer, causing it to fall and cause injuries.

Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable the
Wake-up on LAN function.

Charging the batteries

When the power in the battery pack becomes low, the Battery indicator will
flash orange to indicate that only a few minutes of battery power remain. If
you continue to use the computer while the Battery indicator flashes, the
computer will enable Hibernation Mode so that you do not lose any data,
and automatically turn itself off.
You must recharge a battery pack when it becomes discharged.

Procedures
To recharge a battery pack while it is installed in the computer, connect the
AC adaptor to the DC IN 15V jack and plug the other end into a working
outlet - the Battery indicator will glow orange while the battery is being
charged.
Use only the computer connected to an AC power source or optional
TOSHIBA Battery charger to charge the battery pack. Never attempt to
charge the battery pack with any other charger.

Time
Refer to User Information Guide about Charging time.

User’s Manual 6-5

TECRA A10/S10/M10/SatellitePro S300

Battery charging notice

The battery may not begin charging immediately under the following
conditions:
■ The battery is extremely hot or cold (if the battery is extremely hot,
it might not charge at all). To ensure the battery charges to its full
capacity, you should charge it at room temperature of between 5° to
35°C (41° to 95°F).
■ The battery is nearly completely discharged. In this instance you should
leave the AC adaptor connected for a few minutes and the battery
should begin charging.
The Battery indicator may show a rapid decrease in battery operating time
when you try to charge a battery under the following conditions:
■ The battery has not been used for a long time.
■ The battery has completely discharged and been left in the computer for
a long time.
■ A cool battery is installed in a warm computer.
In such cases you should follow the steps as detailed below:
1. Fully discharge the battery by leaving it in the computer with the power
on until the system automatically turns itself off.
2. Connect the AC adaptor to the DC IN 15V jack of the computer, and to
a wall outlet that is supplying power.
3. Charge the battery until the Battery indicator glows green.
Repeat these steps two or three times until the battery recovers normal
capacity.

Monitoring battery capacity

Remaining battery power can be monitored using the following methods.
■ Clicking the battery icon on the Taskbar
■ Via the Battery Status in the Windows Mobility Center window
■ You should wait at least 16 seconds after turning on the computer
before trying to monitor the remaining operating time. This is because
the computer needs this time to check the battery’s remaining capacity
and then calculate the remaining operating time, based on this together
with the current power consumption.
■ Please be aware that the actual remaining operating time may differ
slightly from the calculated time.
■ With repeated discharges and recharges, the battery’s capacity will
gradually decrease. In view of this it will be noted that an often used,
older battery will not operate for as long as a new battery even when
both are fully charged.

6-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Maximizing battery operating time

A battery’s usefulness depends on how long it can supply power on a
single charge, while how long the charge lasts in a battery depends on:
■ Processor speed
■ Screen brightness
■ System Sleep Mode
■ System Hibernation Mode
■ Display power off period
■ Hard disk drive power off period
■ How often and for how long you use the hard disk drive and external
disk(c) drives, for example, optical disc and floppy diskette drive.
■ How much charge the battery contained to begin with.
■ How you use optional devices, such as a PC Cards, to which the
battery supplies power.
■ Whether you enable Sleep Mode, which can conserve battery power if
you are frequently turning the computer off and on.
■ Where you store your programs and data.
■ Whether you close the display panel when you are not using the
keyboard - closing the display saves power.
■ The environmental temperature - operating time decreases at low
temperatures.
■ The condition of the battery terminals - you should always ensure the
terminals stay clean by wiping them with a clean dry cloth before
installing the battery pack.

Retaining data with power off

Refer to User Information Guide about Retaining time.

Extending battery life

To maximize the life of your battery packs:
■ At least once a month, disconnect the computer from a power source
and operate it on battery power until the battery pack fully discharges.
Before doing so, follow the steps as detailed below.
1. Turn off the computer’s power.
2. Disconnect the AC adaptor and turn on the computer’s power - if it
does not turn on then go to Step 4.
3. Operate the computer on battery power for five minutes. If you find
that the battery pack has at least five minutes of operating time,
continue operating until the battery pack is fully discharged,
however, if the Battery indicator flashes or there is some other
warning to indicate a low battery condition, go to Step 4.

User’s Manual 6-7

TECRA A10/S10/M10/SatellitePro S300

4. Connect the AC adaptor to the DC IN 15V jack of the computer, and

to a wall outlet that is supplying power. The DC IN indicator should
glow green, and the Battery indicator should glow orange to
indicate that the battery pack is being charged, however, in the
event that DC IN indicator does not glow this indicates that power is
not being supplied - check the connections for the AC adaptor and
the power cord.
5. Charge the battery pack until the Battery indicator glows green.
■ If you have extra battery packs, rotate their use.
■ If you will not be using the system for an extended period, for example
for more than one month, remove the battery pack from the computer.
■ Store spare battery packs in a cool dry place out of direct sunlight.

Replacing the battery pack

Please be aware that the battery pack is classified as a consumable item.
The operating life of the battery pack will gradually reduce through
repeated charging and discharging, and will need to be replaced when it
reaches the end of its operating life. In addition to this, you might also
replace a discharged battery pack with a charged spare when you are
operating your computer away from an AC power source for an extended
period of time.
This section explains how to remove and install the battery pack, and begins
with the removal process which is detailed through the following steps.
■ Do not remove the battery pack while the computer is in Sleep Mode.
Data is stored in RAM, so if the computer loses power it could be lost.
■ In Hibernation Mode, data will be lost if you remove the battery pack or
disconnect the AC adaptor before the save is completed. Wait for the
Hard Disk Drive indicator to go out.
■ Do not touch the battery release latch while holding the computer or the
battery pack might fall out due to the unintentional release of the
battery release latch and cause injuries.

Removing the battery pack

To remove a discharged battery, follow the steps as detailed below:
1. Save your work.
2. Turn the computer’s power off - ensure that the Power indicator is off.
3. Remove all cables and peripherals that are connected to the computer.
4. Close the display panel and turn the computer upside down.
5. Slide the battery lock (1) into its ( ) position.

6-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

6. Slide and hold the battery release latch (2) to disengage the battery
pack and then remove it from the computer (3).

Battery release latch

Battery pack

Battery lock

Figure 6-1 Releasing the battery pack

Installing the battery pack

To install a battery pack, follow the steps as detailed below:
Do not touch the battery release latch while holding the computer or the
battery pack might fall out due to the unintentional release of the battery
release latch and cause injuries.

1. Insert the battery pack as far as it will go into the computer (1).
2. Ensure that the battery pack is securely in place and the battery lock (2)
is in its ( ) position.

Battery pack

Battery lock

Figure 6-2 Securing the battery pack

3. Turn your computer over.

User’s Manual 6-9

TECRA A10/S10/M10/SatellitePro S300

TOSHIBA Password Utility

The TOSHIBA Password Utility provides two levels of password security:
User and Supervisor.
Passwords set by the TOSHIBA Password Utility function are different
from the Windows password.

User Password
To start the utility, point to or click the following items:
Start -> All Programs -> TOSHIBA -> Utilities -> Password Utility
The User Password dialog box contains two main fields: User Password
and User Token.
User authentication may be required to validate user rights when using
“TOSHIBA Password Utility” to delete or change passwords, or create
tokens, etc.
User Password field
■ Set (button)
Click this button to register a password of up to 50 characters. After a
password is set, you will be prompted to enter it when you start the
computer. Check “Set the same string simultaneously as the HDD User
Password” when setting the HDD User Password.
■ After you set the password, a dialog box will be displayed asking
whether you want to save it to a floppy diskette or other media. If you
forget the password, you can open the password file on another
computer. Be sure to keep the media in a safe place.
■ When entering the character string to register the password, enter from
the keyboard character by character and do not enter as ASCII code or
copy-and-paste the character string. In addition, ensure that the
registered password is correct by outputting the character string to the
password file.
■ When entering a password, do not enter any characters (for example
“!” or “#”) produced by pressing the SHIFT or ALT keys and so on.

■ Delete (button)
Click this button to delete a registered password. Before you can delete
a password, you must first enter the current password correctly or insert
a proper token. Please use BIOS Setup to change or delete the HDD
Passwords or to set the HDD Master Password.
■ To start BIOS Setup;
1. Turn on the computer while pressing the ESC key.
2. Press the F1 key when directed.
■ To end the BIOS Setup;
1. Press End and then press the Y key to accept the changes.
The computer will restart.

6-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

■ Change (button)
Click this button to change a registered password. Before you can
change a password, you must first enter the current password correctly
or insert a proper token. Please use BIOS Setup to change or delete
the HDD Passwords or to set the HDD Master Password.
■ Owner String (text box)
You can use this box to associate text with the password. After you
enter text, click Apply or OK. When the computer is started, this text
will be displayed together with the prompt asking you to enter a
password.
■ If you forget your HDD User Password, TOSHIBA will NOT be able to
assist you, and your HDD will be rendered COMPLETELY and
PERMANENTLY INOPERABLE. TOSHIBA will NOT be held
responsible for any loss of any data, any loss of use or access to your
HDD, or for any other losses to you or any other person or organization
that result from the loss of access to your HDD. If you can’t accept this
risk, don’t register the HDD User Password.
■ When saving the HDD User Password shut down or restart the
computer. If the computer is not shut down or restarted, the saved data
may not be correctly reflected. For more information on shutting down
or restarting the computer, refer to Turning on the power in Chapter 1.

User Token field

■ Create (button)
You can use an SD Card token, instead of entering the password. After
you have registered a password, insert an SD Card in SD Card slot and
click Create. You can use an SD Card of any capacity, but it must be
formatted correctly.
If an unformatted card or one with an incompatible format is inserted,
you will be prompted to format it with a tool named TOSHIBA SD
Memory Card Format. To start the format tool, point to or click the
following items:
Start -> All Programs -> TOSHIBA -> Utilities -> SD Memory
Card Format
When you format an SD memory card, all data will be deleted. Be sure to
save data on the card to other media before you format the card.

■ Disable (button)
Click this button to invalidate the token. You cannot re-validate old
tokens, but you can use the same SD Cards to create new tokens.
After using the token created for authentication, do not leave it inserted in
the SD Card slot, ensure that the token is removed from the slot and stored
in a safe location. If the token is left in the slot, there is a danger of theft or
a third party using it for authentication and operating the user’s computer
(resulting in extraction, modification or deletion of data) when the user is
not at their desk.

User’s Manual 6-11

TECRA A10/S10/M10/SatellitePro S300

Supervisor Password
If you set a Supervisor Password, some functions might be restricted when
a user logs on with the User Password. To set a Supervisor Password,
execute the file TOSPU.EXE. The file is located at:
C:\Program Files\Toshiba\PasswordUtility\TOSPU.exe
This utility lets you do the following:
■ Register, delete or change the Supervisor Password.
■ Create or invalidate a Supervisor Password token.
This function in the TOSHIBA Password Utility lets you invalidate only
supervisor tokens or all tokens, including user and supervisor tokens.
■ Specify restrictions for general users.

Starting the computer by password

If you have already registered a password, there are three ways to start the
computer:
■ Insert an SD Card token before you turn on the computer. The
computer will start normally, without displaying a password prompt.
■ Swipe your fingerprint on the sensor if you have already registered the
fingerprint with the Fingerprint utility and enabled Fingerprint System
Boot Authentication. If you would not like to swipe your finger or cannot
authenticate the fingerprint for some reasons, push the BACK SPACE
key to skip the fingerprint authentication screen. You can try to swipe
the fingerprint up to five times. If you failed fingerprint authentication
five times, you must enter the password manually to start the computer.
■ Enter the password manually.
The password is necessary only if the computer was turned off in Shut
Down Mode or Hibernation Mode.
It is not needed in Sleep Mode and Restart.

To enter a password manually, follow the steps as detailed below:

1. Turn on the power as described in Chapter 1, Getting Started. The
following message will appear in the screen:
S Password=

2. Enter the Password.

3. Press ENTER.
If you enter the password incorrectly three times in a row, the computer
shuts off. In this case, you must turn the computer back on to retry
password entry.

6-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Power-up modes
The computer has three different power-up modes as follows:
■ Shut Down Mode: The computer will shut down without saving data - in
view of this you must always save your work before you turn the
computer off.
■ Hibernation Mode: Data in memory will be saved to the hard disk drive.
■ Sleep Mode: Data will be maintained in the computer’s memory.
Please refer to the sections Turning on the power and Turning off the
power in Chapter 1, Getting Started for further information.

Windows utilities
You can configure various settings associated with both Sleep Mode and
Hibernation Mode within the Power Options (to access it, Start -> Control
Panel -> System and Maintenance -> Power Options).

Hot keys
You can use the FN + F3 hot key to enter Sleep Mode or FN + F4 to enter
Hibernation Mode - please refer to Chapter 5, The Keyboard for further
details.

Panel power on/off

You can set up your computer so that power is turned off automatically
when you close the display panel, and turned on again when you open it.
Please note that this function is only available for Sleep Mode or
Hibernation Mode, not for Shut Down Mode.
If the panel power off function is enabled, and you manually shut down
Windows, do not close the display panel until the shut down process has
been completed.

System automatic Sleep/Hibernation

This feature automatically turns off the system in Sleep or Hibernation
Mode if the computer is not used for a set duration. Refer to Special
features, in Chapter 3 for an explanation of how to set the duration.

User’s Manual 6-13

TECRA A10/S10/M10/SatellitePro S300

6-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 7

HW Setup

This chapter explains how to use the TOSHIBA HW Setup program to

configure your computer, and provides information on settings for various
functions.

Accessing HW Setup
To run the HW Setup program, click Start -> All Programs -> TOSHIBA ->
Utilities -> HWSetup.

HW Setup window
The HW Setup window contains a number of tabs (General, Display, Boot
Priority, Keyboard, CPU, LAN, Device Config and USB) to allow specific
functions of the computer to be configured.
In addition there are also three buttons: OK, Cancel and Apply.
OK Accepts your changes and closes the HW Setup
window.
Cancel Closes the window without accepting your
changes.
Apply Accepts all your changes without closing the HW
Setup window.

User’s Manual 7-1

TECRA A10/S10/M10/SatellitePro S300

General
This window displays the BIOS version and contains two buttons: Default
and About.
Default Return all HW Setup values to the factory
settings.
About Display the HW Setup version.

Setup
This field displays the installed BIOS version and date.

Display
This tab lets you customize your computer’s display settings for either the
internal display or an external monitor.

Power On Display
This tab allows you to select the display to be used when the computer is
started. Please note that this setting is only available on standard VGA
mode and is not available as part of the Windows Desktop properties.
The Power On Display is supported with some models.

Auto-Selected Selects an external monitor if one is connected,

otherwise, it selects the internal display (default).
LCD + Analog RGB Selects both the internal display and an external
monitor for simultaneous display.

If the connected external monitor does not support the computer’s current
video mode, selecting the LCD + Analog RGB mode will not display any
image on the external monitor.

7-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Boot Priority
Boot Priority Options
This tab allows you to select the priority for booting the computer - the
following settings are available:
FDD −> HDD −> The computer looks for bootable files on devices in
CD-ROM −> LAN the following order: 1. floppy diskette drive*1, 2. hard
disk drive, 3. CD-ROM*2, 4. LAN.
HDD −> FDD −> The computer looks for bootable files on devices in
CD-ROM −> LAN the following order: 1. hard disk drive, 2. floppy
diskette drive*1, 3. CD-ROM*2, 4. LAN.
FDD −> CD-ROM −> The computer looks for bootable files on devices in
LAN −> HDD the following order: 1. floppy diskette drive*1,
2. CD-ROM*2, 3. LAN, 4. hard disk drive.
HDD −> CD-ROM −> The computer looks for bootable files on devices in
LAN −> FDD the following order: 1. hard disk drive, 2. CD-ROM*2,
3. LAN, 4. floppy diskette drive*1.
CD-ROM −> LAN −> The computer looks for bootable files on devices in
FDD −> HDD the following order: 1. CD-ROM*2, 2. LAN, 3. floppy
diskette drive*1, 4. hard disk drive.
CD-ROM −> LAN −> The computer looks for bootable files on devices in
HDD −> FDD the following order: 1. CD-ROM*2, 2. LAN, 3. hard
disk drive, 4. floppy diskette drive*1.

You can override the settings and manually select a boot device by
pressing one of the following keys while the computer is booting:
U Selects the USB floppy diskette drive*1.
N Selects the network.
1 Selects the built-in hard disk drive.
C Selects the CD-ROM*2.
M Selects the USB memory drive.
*1 The floppy diskette drive will be used to start the computer when there is
a bootable disk contained in the external drive. If SD memory card is
installed as well, the external floppy diskette drive will be checked first,
followed by the SD memory device itself.
* The optical disc drive will be used to start the computer when there is a
2

bootable disk contained in the drive.

User’s Manual 7-3

TECRA A10/S10/M10/SatellitePro S300

To change the boot drive, follow the steps below.

1. Hold down F12 and boot the computer.
2. The following menu will be displayed with the following icons: Built-in
hard disk drive, CD-ROM, FDD (or SD memory card), Network (LAN),
USB Memory boot.

Please note that a highlighted bar will only appear under the selected
device.

3. Use the left/right cursor keys to highlight the boot device you want and
press ENTER.
If a Supervisor Password has been set, manual boot device selection
functions may be restricted.
The boot device selection methods described above will not change the
boot priority settings that have been configured in HW Setup. In addition,
if you press a key other than one of those listed, or if the selected device is
not installed, the system will continue to boot according to the current and
available settings in HW Setup.

HDD Priority Options

If more than one hard disk drive is installed in the computer, this option
allows you to set the priority associated with hard disk drive detection - the
first hard disk drive detected that has a valid boot command on it will be the
device from which the computer will start.
Built-in HDD -> This option sets the priority as the built-in hard
USB disk drive followed by a USB memory device
(Default).
USB -> Built-in This option sets the priority as a USB memory
HDD device followed by the built-in hard disk drive.

■ If a boot command is not found on the first detected hard disk drive, the
system will not boot from next hard disk drive in the list, instead it will
search for the next device in the Boot Priority list and startup from this
as appropriate.
■ Please be aware that some modules may not be displayed.

7-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

USB Memory BIOS Support Type

This option allows you to set the type of the USB memory to be used as a
startup device.
HDD Sets the USB memory to be the equivalent of a
hard disk drive (default). With this setting, the
USB memory device can be used to start the
computer as though it were a hard disk drive
based on the hard disk drive settings within both
the Boot Priority and HDD Priority options
detailed previously.
FDD Sets the USB memory to be the equivalent of a
floppy diskette drive. With this setting, the USB
memory device can be used to start the
computer as though it were a floppy diskette
based on the floppy diskette drive settings within
the Boot Priority option detailed previously.

Keyboard
Wake-up on Keyboard
When this feature is enabled, and the computer is in Sleep Mode, you can
turn on the system by pressing any key. However, please be aware that this
option will only work with the internal keyboard and only when the computer
is in Sleep Mode.
Enabled Enables the Wake-up on Keyboard function.
Disabled Disables the Wake-up on Keyboard function
(Default).

User’s Manual 7-5

TECRA A10/S10/M10/SatellitePro S300

CPU
This function allows you to set the processor’s operating mode.

Dynamic CPU Frequency Mode

This option allows you to configure the power saving modes associated
with the processor - the following settings are available:
Dynamically The processor’s power consumption and
Switchable automatic clock speed switching functions are
enabled - in use the processor’s operation is
automatically switched when necessary (default).
Always High The processor’s power consumption and
automatic clock speed switching functions are
disabled - in use the processor will always run at
its highest level of power consumption and its
highest speed.
Always Low The processor’s power consumption and
automatic clock speed switching functions are
disabled - in use the processor will always run at
a lower level of power consumption and a low
speed.

LAN
Wake-up on LAN
This feature lets the computer’s power be turned on when it receives a
wake-up signal from the LAN.
Do not install or remove a memory module while Wake-up on LAN is
enabled.

■ The Wake-up on LAN function consumes power even when the system
is off. Leave the AC adaptor connected while using this feature.
■ To enable it, you must check both the “Allow the device to wake the
computer” and “Only allow management stations to wake the
computer” check box within the “Intel Network Connection”.
Power will be automatically turned on when a signal is received from an
administrator’s computer which is connected via a network.
The following settings can be changed when the Built-in LAN is Enabled.
Connect the AC adaptor when using the Wake-up on LAN function. The
battery retention time will be shorter than the times listed in this manual
when this function is enabled. Refer to the section in chapter 6, Retaining
data with power off.
Enabled Enables Wake-up on LAN (Default).
Disabled Disables Wake-up on LAN.

7-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Built-in LAN
This feature enables or disables the Built-in LAN.
Enabled Enables Built-in LAN functions (Default).
Disabled Disables Built-in LAN functions.

Device Config
Device Configuration
This option allows you to set how the computer’s hardware devices will be
configured.
All Devices The computer’s BIOS will setup and configure all
devices.
Setup by OS The operating system will setup and configure all
of the devices that it can control (default).

USB
USB KB/Mouse Legacy Emulation
You can use this option to enable or disable USB keyboard/mouse legacy
emulation so that, even if your operating system does not support USB
devices, you can still use a standard USB mouse and keyboard - to achieve
this you should set the appropriate option(s) to Enabled.
Enabled Enables the USB KB/Mouse Legacy Emulation
function (Default).
Disabled Disables the USB KB/Mouse Legacy Emulation
function.

USB-FDD Legacy Emulation

Use this option to enable or disable USB floppy diskette drive legacy
emulation. If your operating system does not support USB, you can still use
a USB floppy diskette drive by setting the USB-FDD Legacy Emulation
item to Enabled.
Enabled Enables the USB floppy diskette drive legacy
emulation function (Default).
Disabled Disables the USB floppy diskette drive legacy
emulation function.

User’s Manual 7-7

TECRA A10/S10/M10/SatellitePro S300

7-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Chapter 8

Troubleshooting

TOSHIBA have designed this computer for durability, however, should

problems occur you are able to use the procedures detailed in this chapter
to help determine the cause.
All users should become familiar with this chapter as knowing what might
go wrong can help prevent problems from occurring in the first place.

Problem solving process

Resolving problems will be much easier if you observe the following
guidelines:
■ Stop immediately when you recognize a problem exists as taking further
action may result in data loss or damage, or you may destroy valuable
problem related information that can help solve the problem.
■ Observe what is happening - write down what the system is doing and
what actions you performed immediately before the problem occurred.
If you have a printer attached, print a copy of the screen using the
computer’s PRTSC key.
Please also be aware that the questions and procedures described in this
chapter are meant only as a guide, they are not definitive problem solving
techniques. In reality many problems can be solved simply, but a few may
require help from your reseller, dealer or service provider - if you find you
need to consult others, be prepared to describe the problem in as much
detail as possible.

Preliminary checklist
You should always consider the simplest solution first - the items detailed in
this checklist are easy to fix and yet can cause what appears to be a
serious problem:
■ Make sure you turn on all peripheral devices before you turn on the
computer - this includes your printer and any other external device you
are using.
■ Before you attach an external device you should first turn the computer
off, then when you turn the computer back on again it will recognize the
new device.

User’s Manual 8-1

TECRA A10/S10/M10/SatellitePro S300

■ Make sure all optional accessories are configured properly in the

computer’s setup program and that all required driver software has
been loaded (please refer to the documentation included with the
optional accessories for further information on its installation and
configuration).
■ Check all cables to ensure they are correctly and firmly attached to the
computer - loose cables can cause signal errors.
■ Inspect all connecting cables for loose wires and all connectors for
loose pins.
■ Check that your floppy diskette, CD or DVD media is correctly loaded
and, in the case of a floppy diskette, that its write protect tab is
correctly set.
Always try to make detailed notes of your observations and keep them in a
permanent error log - this will help you to describe your problems to your
reseller, dealer or service provider. In addition, if a problem recurs, the log
you have made will help to identify the problem faster.

Analyzing the problem

Sometimes the computer will give you clues that can help you identify why
it is malfunctioning. In view of this you should keep the following questions
in mind:
■ Which part of the computer is not operating properly - keyboard, hard
disk drive, display panel, touch pad, touch pad control buttons - as each
device will produce different symptoms.
■ Check the options within the operating system to ensure that its
configuration is set properly.
■ What appears on the display? Does it display any messages or random
characters? If you have a printer attached, print a copy of the screen
using the PRTSC key and, if possible, look up the messages in the
documentation included with the computer, software or operating
system.
■ Check that all connecting cables are correctly and firmly attached as
loose cables can cause erroneous or intermittent signals.
■ Do any indicators light, if so, which ones, what color are they and do
they stay on or blink? Write down what you see.
■ Do you hear any beeps, if so how many, are they long or short and are
they high pitched or low pitched? In addition, is the computer making
any unusual noises? Write down what you hear.
Record your observations so you can describe them in detail to your
reseller, dealer or service provider.

8-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Software The problems may be caused by your software or disk. If

you cannot load a software package, the media may be
damaged or the program might be corrupted - in these
instances try loading another copy of the software if
possible.
If an error message appears while you are using a software
package you should refer to the documentation supplied
with it as this will usually include a problem solving section
or a summary of error messages.
Next, you should check any error messages against the
operating system documentation.
Hardware If you cannot find a software problem, you should then
check the setup and configuration of your hardware. First
run through the items in the preliminary checklist as
described previously then, if you still cannot correct the
problem, try to identify the source - the next section
provides checklists for individual components and
peripherals.

Before using a peripheral device or application software that is not an

authorized Toshiba part or product, make sure the device or software can
be used with your computer. Use of incompatible devices may cause injury
or may damage your computer.

Hardware and system checklist

This section discusses problems caused by your computer’s hardware or
attached peripherals. Basic problems may occur in the following areas:
■ System start-up ■ MultiMediaCard
■ Self test ■ Dual Pointing Device
■ Power ■ Fingerprint Sensor
■ Password ■ USB device
■ Keyboard ■ eSATA device
■ Internal display panel ■ Additional memory module
■ Hard disk drive ■ Sound system
■ DVD-ROM drive ■ Volume control dial
■ DVD-ROM & CD-R/RW drive ■ External monitor
■ DVD Super Multi drive ■ i.LINK (IEEE1394) device
■ USB floppy diskette drive ■ Modem
■ PC Card ■ LAN
■ Smart Card ■ Wireless LAN
■ SD/SDHC Card ■ Bluetooth
■ Memory Stick ■ Recovery Discs
■ xD picture card

User’s Manual 8-3

TECRA A10/S10/M10/SatellitePro S300

System start-up
When the computer does not start properly, check the following items:
■ Self Test
■ Power Sources
■ Power-on Password

Self test
While booting up the computer, self test is executed automatically and the
TOSHIBA logo is displayed on the screen.
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating system
according to how the Boot Priority option is set within the TOSHIBA HW
Setup program.
If any of the following conditions are present, the self test has failed:
■ The computer stops and does not proceed to display information or
messages except for the TOSHIBA logo.
■ Random characters appear on the screen and the system does not
function normally.
■ The screen displays an error message.
In these instances, turn off the computer, check all cable connections and
then restart it - if the self test fails again, contact your reseller, dealer or
service provider.

Power
When the computer is not plugged into an AC power outlet, the battery
pack is the primary power source. However, your computer also has a
number of other power resources, including an intelligent power supply and
a Real Time Clock (RTC) battery, all of which are interrelated with any one
having the ability to produce apparent power problems.
This section provides checklists for AC power and the battery. If you cannot
resolve a problem after following them, the cause may lie with another
power related resource - in such an instance you should contact your
reseller, dealer or service provider.

8-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Overheating power down

If the processor’s temperature reaches an unacceptably high level with
either setting, the computer will automatically shuts down to prevent any
damage - in this instance all unsaved data in memory will be lost.
Problem Procedure
Computer shuts down Leave the computer off until the DC IN indicator
and DC IN indicator stops blinking.
blinks orange

It is recommended to leave the computer off until the interior reaches room
temperature even though the DC IN indicator stops blinking.

If the computer has reached room temperature

and it still does not start, or if it starts but shuts
down quickly, contact your reseller, dealer or
service provider.
Computer shuts down This indicates a problem with the heat dispersal
and its DC IN indicator system - you should contact your reseller, dealer
is flashing green or service provider.

AC power
If you have trouble turning on the computer with the AC adaptor connected
you should check the status of the DC IN indicator. Please refer to
Chapter 6, Power and Power-Up Modes, for further information.
Problem Procedure
AC adaptor doesn’t Check the connections to make sure that the
power the computer power cord/adaptor is firmly connected to the
(DC IN indicator does computer and a working power outlet.
not glow green)
Check the condition of the cord and terminals.
If the cord is frayed or damaged it should be
replaced, while if the terminals are soiled, they
should be cleaned with a clean cotton cloth.
If the AC adaptor still does not power the
computer, you should contact your reseller,
dealer or service provider.

User’s Manual 8-5

TECRA A10/S10/M10/SatellitePro S300

Battery
If you suspect a problem with the battery, you should check the status of
the DC IN indicator as well as the Battery indicator. Please refer to
Chapter 6, Power and Power-Up Modes, for more information on these
indicators, together with general battery operation.
Problem Procedure
Battery doesn’t power The battery may be discharged - connect the AC
the computer adaptor to recharge the battery.
Battery doesn’t If the battery is completely discharged, it will not
charge when the AC begin charging immediately, in these instances
adaptor is attached you should wait a few minutes before trying again.
(Battery indicator If the battery still does not charge, you should
does not glow check that the power outlet the AC adaptor is
orange). connected to is supplying power - this can be
tested by plugging another appliance into it.
Check whether the battery is hot or cold to the
touch - if so, it will not charge properly and should
be allowed to reach room temperature before
you try again.
Unplug the AC adaptor and remove the battery to
make sure its connecting terminals are clean - if
necessary wipe them with a soft dry cloth lightly
dipped in alcohol.
Connect the AC adaptor and replace the battery,
taking care to ensure that it is securely seated in
the computer.
Check the Battery indicator - if it does not glow,
allow the computer to charge the battery for at
least twenty minutes. If the Battery indicator
starts to glow after this period, allow the battery
to continue to charge for at least another twenty
minutes before turning on the computer.
However, if the indicator still does not glow, the
battery may be at the end of its operating life and
should be replaced. However, if you do not
believe the battery is at the end of its operating
life, you should speak to your reseller, dealer or
service provider.
Battery doesn’t power If you frequently recharge a partially charged
the computer as long battery, the battery might not charge to its full
as expected potential - in these instances you should fully
discharge the battery and then attempt to charge
it again.
Check the Power saver option under Select a
power plan in the Power Options.

8-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Real Time Clock

Problem Procedure
The following The charge in the Real Time Clock (RTC) battery
message is Displayed has run out - you will need to set the date and
on the screen: time in the BIOS setup application by using the
RTC battery is following steps:
low or CMOS 1. Press the F1 key - the BIOS setup application
checksum is will load.
inconsistent. 2. Set the date in the System Date field.
Press [F1] key
to set 3. Set the time in the System Time field.
Date/Time. 4. Press the END key - a confirmation message
will be displayed.
5. Press the Y key - the BIOS setup application
will end and the computer will restart.

Password

Problem Procedure
Cannot enter password Please refer to the TOSHIBA Password Utility
section in Chapter 6, Power and Power-Up
Modes, for further information.

Keyboard
Keyboard problems can be caused by the setup and configuration of the
computer - please refer to Chapter 5, The Keyboard, for further information.

Problem Procedure
Some letter keys Check that the numeric keypad overlay is not
produce numbers activated - press the FN + F11 hot key and try
typing again.
Output to screen is Please refer to your software’s documentation to
garbled ensure that its is not remapping the keyboard in
any way (remapping involves changing or
reassigning the function of each key).
If you are still unable to use the keyboard, you
should contact your reseller, dealer or service
provider.

User’s Manual 8-7

TECRA A10/S10/M10/SatellitePro S300

Internal display panel

Apparent computer’s display panel problems may be related to the
computer’s setup and configuration - please refer to Chapter 7, HW Setup,
for further information.
Problem Procedure
No display Press the FN + F5 hot keys to adjust the display
priority, and to make sure it is not set for output to
an external monitor.
Markings appear on These marks may have come from contact with
the computer’s the keyboard and Touch Pad while the display
display panel. panel has been closed. You should try to remove
the marks by gently wiping the display panel with
a clean dry cloth or, if this fails, with a good
quality LCD screen cleaner. In this latter instance
you should always follow the instructions with the
screen cleaner and always ensure you let the
display panel dry properly before closing it.
Problems above You should initially refer to the documentation
remain unresolved or supplied with you software to determine if it is
other problems occur this that is causing the problems. Alternatively
you may wish to run the TOSHIBA PC
Diagnostic Tool to check the general operation
of the computer.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

Hard disk drive

Problem Procedure
Computer does not Check to see whether that is a floppy diskette in
boot from hard disk the floppy diskette drive or a CD-ROM/DVD-
drive ROM in the optical disc drive - if so remove it and
try to start the computer again.
If this has no effect, check the Boot Priority
setting within the TOSHIBA HW Setup utility -
please refer to the Boot Priority section in
Chapter 7, HW Setup, for further information.
Please refer to your operating system
documentation in order to determine whether
there is a problem with any of the operating
system files or settings.

8-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Problem Procedure
Slow performance The files on the hard disk drive may be
fragmented - in this instance you should run the
disk Defragmentation utility to check the
condition of your files and the hard disk drive.
Please refer to the operating system’s
documentation or online Help File for further
information on operating and using the
Defragmentation utility.
As a last resort you should reformat the hard disk
drive and then reload the operating system and
all other files and data. If you are still unable to
resolve the problem, contact your reseller, dealer
or service provider.

DVD-ROM drive
For more information, refer to Chapter 4, Operating Basics.
Problem Procedure
You cannot access a Make sure the drive’s disc tray is securely
CD/DVD in the drive closed.
Press gently until it clicks into place.
Open the disc tray and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the disc tray could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe it
with a clean cloth dipped in water or a neutral
cleaner. Refer to the Media care section in
Chapter 4, for details on cleaning.

User’s Manual 8-9

TECRA A10/S10/M10/SatellitePro S300

Problem Procedure
Some CD/DVDs run The software or hardware configuration may be
correctly, but others causing a problem. Make sure the hardware
do not configuration matches your software’s needs.
Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM: DVD-ROM, DVD-Video
CD-ROM: CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD
(CD-EXTRA), Addressing Method 2
Check the region code on the DVD. It must
match that on the DVD-ROM. Region codes are
listed in the Optical disc drives section in
Chapter 2, The Grand Tour.

DVD-ROM & CD-R/RW drive

For more information, refer to Chapter 4, Operating Basics.
Problem Procedure
You cannot access a Make sure the drive’s disc tray is securely
CD/DVD in the drive closed.
Press gently until it clicks into place.
Open the disc tray and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the disc tray could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe it
with a clean cloth dipped in water or a neutral
cleaner. Refer to the Media care section in
Chapter 4, for details on cleaning.

8-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Problem Procedure
Some CD/DVDs run The software or hardware configuration may be
correctly, but others causing a problem. Make sure the hardware
do not configuration matches your software’s needs.
Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM: DVD-ROM, DVD-Video
CD-ROM: CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD
(CD-EXTRA), Addressing Method 2
Recordable CD: CD-R, CD-RW
Check the region code on the DVD. It must
match that on the DVD-ROM&CD-R/RW drive.
Region codes are listed in the Optical disc drives
section in Chapter 2, The Grand Tour.
Cannot write correctly If you have trouble writing, make sure you are
observing the following precautions:
■ Use only media recommended by TOSHIBA.
■ Do not use the mouse or keyboard during
writing.
■ Use only the software supplied with the
computer for recording.
■ Do not run or start other software during
writing.
■ Do not jar the computer during writing.
■ Do not connect/disconnect external devices
or install/remove internal cards during writing.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-11

TECRA A10/S10/M10/SatellitePro S300

DVD Super Multi drive

For more information, refer to Chapter 4, Operating Basics.
Problem Procedure
You cannot access a Make sure the drive’s disc tray is securely
CD/DVD in the drive closed.
Press gently until it clicks into place.
Open the disc tray and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the disc tray could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe it
with a clean cloth dipped in water or a neutral
cleaner. Refer to the Media care section in
Chapter 4, for details on cleaning.
Some CD/DVDs run The software or hardware configuration may be
correctly, but others causing a problem. Make sure the hardware
do not configuration matches your software’s needs.
Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using.
The drive supports:
DVD-ROM: DVD-ROM, DVD-Video
CD-ROM: CD-DA, CD-Text, Photo CD (single/
multi-session), CD-ROM Mode 1,
Mode 2, CD-ROM XA Mode 2
(Form1, Form2), Enhanced CD
(CD-EXTRA), Addressing Method 2
Recordable DVD: DVD-R/-R DL, DVD+R/+R DL,
DVD-RW, DVD+RW, DVD-RAM
Check the region code on the DVD. It must
match that on the DVD Super Multi drive. Region
codes are listed in the Optical disc drives section
in Chapter 2, The Grand Tour.

8-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

USB floppy diskette drive

For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
Drive does not operate Check the connection between the computer and
the drive to ensure that it is properly attached.
Some programs run The computer’s software or hardware
correctly but others do configuration may be causing a problem - ensure
not that these configurations match your
requirements (refer to any relevant
documentation, for example that supplied with
any software in use, for further information).
You cannot access the Try another floppy diskette in the drive - if you are
external floppy diskette able to access this disk then it indicates the
drive original disk and not the drive is probably causing
the problem.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

PC Card
For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
PC Card error occurs Remove the PC Card from the computer and
then reinsert it in order to ensure it is firmly
connected.
In the event that the PC Card is attached to an
external peripheral device, ensure that this
connection is properly made.
If the problem persists, then you should refer to
the documentation supplied with your PC Card
for further information.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-13

TECRA A10/S10/M10/SatellitePro S300

SD/SDHC Card
For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
SD/SDHC Card error Remove the SD/SDHC Card from the computer
occurs and then reinsert it in order to ensure it is firmly
connected.
If the problem persists, then you should refer to
the documentation supplied with your SD/SDHC
Card for further information.
You cannot write to an Remove the SD/SDHC Card from the computer
SD/SDHC Card and check to ensure that it is not write protected.
You cannot read a file Check to ensure the required file is actually on
the SD/SDHC Card that is inserted into the
computer.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

Smart Card
For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
Smart Card error Remove the Smart Card from the computer,
occurs make sure to confirm that the card oriented
correctly and reinsert it in order to ensure it is
firmly connected.
If the problem persists, then you should refer to
the documentation supplied with your Smart
Card for further information.

8-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Memory Stick
For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
Memory Stick/Memory Remove the Memory Stick/Memory Stick PRO/
Stick PRO/Memory Memory Stick PRO Duo from the computer and
Stick PRO Duo error then reinsert it in order to ensure it is firmly
occurs connected.
If the problem persists, then you should refer to
the documentation supplied with your Memory
Stick/Memory Stick PRO/Memory Stick PRO Duo
for further information.
You cannot write to an Remove the Memory Stick/Memory Stick PRO/
Memory Stick/Memory Memory Stick PRO Duo from the computer and
Stick PRO/Memory check to ensure that it is not write protected.
Stick PRO Duo
You cannot read a file Check to ensure the required file is actually on
the Memory Stick/Memory Stick PRO/Memory
Stick PRO Duo that is inserted into the computer.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

xD picture card
For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
xD picture card error Remove the xD picture card from the computer
occurs and then reinsert it in order to ensure it is firmly
connected.
If the problem persists, then you should refer to
the documentation supplied with your xD picture
card for further information.
You cannot read a file Check to ensure the required file is actually on
the xD picture card that is inserted into the
computer.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-15

TECRA A10/S10/M10/SatellitePro S300

MultiMediaCard
For further information, please refer to Chapter 3, Hardware, Utilities and
Options.
Problem Procedure
MultiMediaCard error Remove the MultiMediaCard from the computer
occurs and then reinsert it in order to ensure it is firmly
connected.
If the problem persists, then you should refer to
the documentation supplied with your
MultiMediaCard for further information.
You cannot write to a Remove the MultiMediaCard from the computer
MultiMediaCard and check to ensure that it is not write protected.
You cannot read a file Check to ensure the required file is actually on
the MultiMediaCard that is inserted into the
computer.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

Dual Pointing device

If you are using a USB mouse, you should also refer to both the USB
device section in this chapter, and the documentation supplied with your
mouse.

Touch Pad/AccuPoint

Problem Procedure
Either the Touch Pad Check the Device Select settings.
or the AccuPoint does Click Start -> Control Panel -> Hardware and
not work. Sound -> Mouse icon.
Pressing FN + F9 to enables.
On-screen pointer In this instance the system might be busy - Try
does not respond to moving the mouse again after waiting a short
pointing device while.
operation

8-16 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Problem Procedure
Double-tapping (Touch In this instance, you should initially try changing
Pad) or double- the double-click speed setting within the Mouse
clicking (AccuPoint) Control utility.
does not work 1. To access this utility, click Start -> Control Panel
-> Hardware and Sound -> Mouse icon.
2. Within the Mouse Properties window, click
the Buttons tab.
3. Set the double-click speed as required and
click OK.
The on-screen pointer In this instance, you should initially try changing
moves too fast or too the speed setting within the Mouse Control utility.
slow 1. To access this utility, click Start -> Control
Panel -> Hardware and Sound -> Mouse
icon.
2. Within the Mouse Properties window, click
the Pointer Options tab.
3. Set the pointer speed as required and click
OK.
The reaction of Touch Adjust the touch Sensitivity.
pad is either too 1. Click Start -> Control Panel -> Hardware
sensitive or not and Sound -> Mouse icon.
sensitive enough.
2. Within the Mouse Properties window, click
the Advanced tab.
3. Click the Advanced feature settings...
button.
4. Advanced feature settings is displayed.
5. Within the Pointer speed and tapping
settings, click Settings... button.
6. Detailed Touch Pad settings window is
displayed.
7. Move the slider bar to adjust the sensitivity in
the Touch Sensitivity.
8. Click OK button.
9. Click the OK button on Advanced feature
setting screen.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-17

TECRA A10/S10/M10/SatellitePro S300

USB mouse

Problem Procedure
On-screen pointer In this instance the system might be busy - Try
does not respond to moving the mouse again after waiting a short
mouse operation while.
Remove the mouse from the computer and then
reconnect it to a free USB port it in order to
ensure it is firmly attached.
Double-clicking does In this instance, you should initially try changing
not work the double-click speed setting within the Mouse
Control utility.
1. To access this utility, click Start -> Control
Panel -> Hardware and Sound -> Mouse
icon.
2. Within the Mouse Properties window, click
the Buttons tab.
3. Set the double-click speed as required and
click OK.
The on-screen pointer In this instance, you should initially try changing
moves too fast or too the speed setting within the Mouse Control utility.
slow 1. To access this utility, click Start -> Control
Panel -> Hardware and Sound -> Mouse
icon.
2. Within the Mouse Properties window, click
the Pointer Options tab.
3. Set the pointer speed as required and click
OK.
The on-screen pointer The elements of the mouse responsible for
moves erratically detecting movement might be dirty - please refer
to the documentation supplied with the mouse for
instructions on how to clean it.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

8-18 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Fingerprint Sensor

Problem Procedure
Reading of the In this instance you should try the fingerprint
fingerprint was not reading operation again using the correct finger
successful. position - please refer to Using the Fingerprint
Sensor in Chapter 4, Operating Basics, for
further information.
Alternatively, you should try the recognition
process again using another enrolled finger.
The fingerprint sensor compares and analyzes
the unique characteristics in a fingerprint.
However, there may be instances where certain
users are unable to register their fingerprints due
to insufficient unique characteristics in their
fingerprints.
The recognition success rate may differ from
user to user.
The fingerprint cannot In this instance you should try the recognition
be read due to injuries process again using another enrolled finger.
to the finger. However, if fingerprints from all the enrolled
fingers cannot be read, you should instead log
into the computer by using the keyboard to input
the password.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

USB device
In addition to the information in this section, please also refer to the
documentation supplied with your USB device.
Problem Procedure
USB device does not Remove the USB device from the computer and
work then reconnect it to a free port it in order to
ensure it is firmly attached.
Ensure that any required USB device drivers are
properly installed - to achieve this you should
refer to both the device documentation and the
operating system documentation.
If you are using an operating system that does
not support USB, you are still able to use a USB
mouse and/or USB keyboard by setting the USB
KB/Mouse Emulation option within the
TOSHIBA HW Setup utility to Enabled.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-19

TECRA A10/S10/M10/SatellitePro S300

USB Sleep and Charge function

For more information and settings, please refer to the Using the TOSHIBA
USB Sleep and Charge Utility section in Chapter 4, Operating Basics.
Problem Procedure
I cannot use the “USB The setting of “USB Sleep and Charge function”
Sleep and Charge may be [Disabled]. Change the setting to
function”. [Enabled].
When there is a current overflow of the external
device connected to the compatible port, USB
bus power (DC5V) supply may be stopped for
safety reasons. When this happens, disconnect
an external device if some external devices are
connected. After that, turn the power of the
computer ON/OFF to restore the function. If this
function can not be still used even if only one
external device is connected, stop using the
external device because its current is over the
acceptable value of this computer.
Some external devices may not be able to use
the “USB Sleep and Charge function”. In this
case, please try one or more of the following
methods.
■ Change a mode setting of [Enabled].
■ Turn OFF the computer while external
devices are connected.
■ Connect external devices after turning OFF of
the computer.
If this function can not be still used, change the
setting to [Disabled] and stop using this function.
The battery depletes When “USB Sleep and Charge function” is set to
quickly even when I [Enabled], USB bus power (DC5V) will be
turned OFF the power supplied to the external device connected to the
of the computer. compatible port. If external device is connected
to the compatible port when the AC adaptor is
not connected to the computer, the battery of the
computer will be depleted even when the power
of the computer is turned OFF.
Connect the AC adaptor to the computer or
change the “USB Sleep and Charge function”
setting to [Disabled] or if there is a USB port that
does not have the USB Sleep and Charge
function-compatible icon ( ), use that port.

8-20 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Problem Procedure
External devices Some external devices may not work when
connected to the connected to a compatible port when the “USB
compatible ports do Sleep and Charge function” is [Enabled].
not work when Reconnect the external device after turning ON
connected to a the computer.
compatible port.
If the external device still does not work, connect
device to a USB port, if there is one, that does
not have the USB Sleep and Charge function-
compatible icon ( ) or change the “USB Sleep
and Charge function” setting to [Disabled].
The “USB Wakeup When “USB Sleep and Charge function” is set to
function” does not [Enabled], the “USB Wakeup function” does not
work. work for ports that support the USB Sleep and
Charge function.
In that case, use a USB port, if there is one, that
does not have the USB Sleep and Charge
function-compatible icon ( ) or change the
“USB Sleep and Charge function” setting to
[Disabled].

eSATA device
In addition to the information in this section, please also refer to the
documentation supplied with your eSATA device.
Problem Procedure
eSATA device does Remove the eSATA device from the computer
not work and then reconnect it to a free port it in order to
ensure it is firmly attached.
A connected eSATA device may not be
recognized if it is connected to the computer’s
eSATA/USB combo port while the computer is in
Sleep Mode or Hibernation Mode. If this occurs,
disconnect the eSATA device and then reconnect
the device while the computer is turned on.
Ensure that any required eSATA device drivers
are properly installed - to achieve this you should
refer to both the device documentation and the
operating system documentation.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-21

TECRA A10/S10/M10/SatellitePro S300

Additional memory module

Please also refer to Chapter 3, Hardware, Utilities and Options, for further
information on installing and removing memory modules.
Problem Procedure
If there is a memory In the event the Power indicator flashes when
malfunction, the the computer is turned on, you should first check
Power indicator will that the installed memory module(s) are
repeatedly flash (on compatible with the computer. If there is an error
for 0.5 seconds, off for with a compatible memory module, there is a
0.5 seconds) in the possibility the memory module is damaged.
following patterns;
If you determine that an incompatible module has
If there is an error in been installed, you should follow the steps as
only slot A or no detailed below:
memory module is
inserted in Slot A: 1. Turn off the computer.
orange twice, then 2. Disconnect the AC adaptor and all peripheral
green once. devices.
If there is an error in 3. Remove the battery pack.
Slot B: orange once, 4. Remove the incompatible memory module.
then green twice.
5. Install the battery and/or connect the AC
If there are errors in adaptor.
both Slot A and Slot B:
orange twice, then 6. Turn on the computer.
green twice. If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.
An error will occur if a Remove the memory module from Slot B and
memory module is insert it into Slot A.
inserted into Slot B
while no memory
module is inserted in
Slot A.

8-22 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Sound system
In addition to the information in this section, please also refer to the
documentation supplied with your audio device.
Problem Procedure
No sound is heard Adjust the volume control dial.
To increase the volume move the volume control
dial to the right, and to decrease it move the
volume control dial to the left.
Check the software volume settings.
Please check to see if Mute is turned to Off
Check to make sure the headphone connection
is secure.
Check within the Windows Device Manager
application to ensure the sound device is
enabled and that the device is properly working.
For further information, please refer to
“Troubleshooting in Windows” section of
Windows Help and Support.
Annoying sound is In this instance you may be experiencing
heard feedback from either the internal microphone or
an external microphone connected to the
computer - please refer to Sound System in
Chapter 4, Operating Basics, for further
information.
Volume cannot be adjusted during Windows start
up or shut down.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

Volume control dial

Problem Procedure
No sound is heard Adjust the volume control dial.
To increase the volume move the volume control
dial to the right, and to decrease it move the
volume control dial to the left.
Turn the volume control dial while verifying the
volume in order to adjust.
Annoying sound is Volume cannot be adjusted during Windows start
heard up or shut down.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

User’s Manual 8-23

TECRA A10/S10/M10/SatellitePro S300

External monitor
Please also refer to Chapter 3, Hardware, Utilities and Options, and to the
documentation supplied with your monitor for further information.
Problem Procedure
Monitor does not turn After confirming that the monitor’s power switch
on is on, you should check the connections to make
sure that the power cord/adaptor is firmly
connected to the monitor and to a working power
outlet.
No display Try adjusting the contrast and brightness controls
on the external monitor.
Press the FN + F5 hot key in order to change the
display priority and ensure that it is not set for the
internal display only.
Check to see if the external monitor is connected.
When the external monitor is set as the primary
display device in extended desktop mode, it will
not display when the computer wakes up from
Sleep Mode if the external monitor has been
disconnected while in Sleep Mode.
To keep this from happening, do not disconnect
the external monitor while the computer is in
Sleep or Hibernation Mode.
Remember to turn off the computer before
disconnecting the external monitor.
When the display panel and an external monitor
are set to clone mode and they are turned off by
the timer, the display panel or the external
monitor may not display when turned on again.
If this occurs, press FN + F5 to re-set the display
panel and external monitor to clone mode.
Display error occurs Check that the cable connecting the external
monitor to the computer is firmly attached.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

8-24 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

i.LINK (IEEE1394) device

Problem Procedure
i.LINK device does not Make sure the cable is securely connected to the
function computer and to the device.
Make sure the device’s power is turned on.
Reinstall the drivers. Open the Windows
Control Panel and double-click the Add
Hardware icon. Follow the on-screen
directions.
Restart Windows.
If problems persist, contact your dealer.

Modem

This information is applicable to the models equipped with a built-in

modem.

Problem Procedure
Communication Make sure the computer’s internal modem
software can’t initialize settings are correct - please refer to the Phone
modem and Modem Options link within the Windows
Control Panel.
You can hear a dial If the call is going through a Private Branch
tone but can’t make a Exchange (PBX), take care to ensure that the
call communication application’s tone dial detection
feature is disabled.
You place a call, but a Make sure that the settings are correct within
connection can’t be your communication application.
made
After making a call you Ensure that the communication application’s tone
can’t hear a ring or pule dialling selection feature is set correctly.
Communication is cut The computer will automatically cut off
off unexpectedly communication when connection with the carrier
is not successful for a set time interval - try
lengthening this time interval within your
communication application.
A CONNECT display is Ensure that the communication application’s
quickly replaced by NO error control feature is set correctly.
CARRIER

User’s Manual 8-25

TECRA A10/S10/M10/SatellitePro S300

Problem Procedure
Character display When transmitting data you should ensure that
becomes garbled the parity bit and stop bit settings correspond
during a with those of the remote computer - you should
communication check the flow control and communication
protocol settings within your communication
application.
You cannot receive an Ensure that the communication application’s
incoming call rings before auto answer feature is set correctly.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

LAN

Problem Procedure
Cannot access LAN Check for a firm cable connection between the
LAN jack and the LAN hub.
Wake-up on LAN does Make sure the AC adaptor is connected. The
not work Wake-up on LAN function consumes power even
when the system is off.
If problems persist, consult your LAN
administrator.

Wireless LAN
If the following procedures do not restore LAN access, consult your LAN
administrator. For more information on wireless communication, refer to
Chapter 4, Operating Basics.
Problem Procedure
Cannot access Make sure the computer’s Wireless
Wireless LAN communication switch is set to on.
If problems persist, contact your LAN
administrator.

8-26 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Bluetooth
For further information on Bluetooth wireless communication, please refer
to Chapter 4, Operating Basics.

Problem Procedure

Cannot access Check to ensure the computer’s Wireless

Bluetooth device Communication Switch is set to on.

Check to ensure the Bluetooth Manager

application is running on the computer and that
power to the external Bluetooth device is turned
on.

Check to ensure that no optional Bluetooth

Adaptor is installed in the computer - the built-in
Bluetooth hardware cannot operate
simultaneously with another Bluetooth controller.
If you are still unable to resolve the problem,
contact your reseller, dealer or service provider.

Recovery Discs

Problem Procedure
The following You will see this message if you have previously
message appears chosen to remove the partition and are trying to
when executing create “Recovery Media”.
Recovery Disc When there is no recovery partition, the Recovery
Creator. Disc Creator cannot make Recovery Media.
“The Recovery However, if you have already created a
Disc Creator can “Recovery Media”, you can use it to restore the
not be launched recovery partition.
because there is
no recovery Simply follow the instructions in Restoring the
partition.” pre-installed software from your created
Recovery Discs section in Chapter1, Getting
Started.
You will be directed to select “Restore Original
Factory Image” from the drop-down menu.
If you have not created “Recovery Media”, please
contact TOSHIBA support for assistance.

User’s Manual 8-27

TECRA A10/S10/M10/SatellitePro S300

TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for
additional technical assistance.
Before you call
Some problems you experience may be related to software or the operating
system so it is important that you investigate other sources of assistance
first. Before contacting TOSHIBA, try the following:
■ Review troubleshooting sections in the documentation supplied with
your software and/or peripheral devices.
■ If a problem occurs when you are running software applications, consult
the software documentation for troubleshooting suggestions and
consider calling the software company’s technical support department
for assistance.
■ Consult the reseller or dealer from where you purchased your computer
and/or software - they are your best resource for current information
and support.

Where to write
If you are still unable to solve the problem and suspect that it is hardware
related, write to TOSHIBA at the location listed in the accompanying
warranty booklet or visit www.toshiba-europe.com on the internet.

8-28 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix A

Specifications

This appendix summarizes the computer’s technical specifications.

Environmental Requirements

Conditions Ambient temperature Relative humidity

Operating 5°C (41°F) to 35°C (95°F) 20% to 80%
(noncondensing)
Non-operating -20°C (-4°F) to 65°C (149°F) 10% to 90%
(noncondensing)
Wet-bulb 26°C maximum
temperature
Conditions Altitude (from sea level)
Operating -60 to 3,000 meters
Non-operating -60 to 10,000 meters
maximum

Power Requirements

AC adaptor 100-240 volts AC

50 or 60 hertz (cycles per second)
Computer 15 V DC
5.0 amperes

User’s Manual A-1

TECRA A10/S10/M10/SatellitePro S300

Built-in Modem

This information is applicable to the models equipped with a built-in

modem.

Network control unit (NCU)

Type of NCU AA
Type of line Telephone line (analog only)
Type of dialing Pulse
Tone
Control command AT commands
EIA-578 commands
Monitor function Computer’s speaker
Communication specifications
Communication system Data: Full duplex
Fax: Half duplex
Communication protocol Data
ITU-T-Rec V.21/V.22/V.22bis/V.32/V.32bis/
(Former CCITT) V.34/V.90
Bell 103/212A
Fax
ITU-T-Rec V.17/V.29/V.27ter/V.21 ch2
(Former CCITT)
Communication speed Data transmission and reception
300/1200/2400/4800/7200/9600/12000/14400/16800/
19200/21600/24000/26400/28800/31200/33600 bps
Data reception only with V.90
28000/29333/30666/32000/33333/34666/36000/37333/
38666/40000/41333/42666/44000/45333/46666/48000/
49333/50666/52000/53333/54666/56000 bps
Fax
2400/4800/7200/9600/12000/14400 bps
Transmitting level -10 dBm
Receiving level -10 to -40 dBm
Input/output impedance 600 ohms ±30%
Error correcting MNP class 4 and ITU-T V.42
Data compression MNP class 5 and ITU-T V.42bis
Power supply +3.3V (supplied by computer)

A-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix B

Display Controller and Video mode

Display controller
The display controller interprets software commands into hardware
commands that turn particular parts on the screen on or off.
Due to the display panel’s increased resolution, lines may appear broken
in when displaying images in full-screen text mode.
The display controller also controls the video mode and uses industry
standard rules to govern the screen resolution and the maximum number of
colors that can be displayed at any one time. Therefore, software written for
a given video mode will run on any computer that supports that mode.

Video mode
Video mode settings are configured via the Display Properties dialog.
To open the Display Properties dialog, click Start -> Control Panel ->
Appearance and Personalization -> Personalization -> Display
Settings.
If you are running some applications (for example a 3D application or video
playback and so on), you may see some disturbance, flickering or frame
dropping on your screen.
If that occurs, adjust the resolution of display, lowering it until the screen is
displayed properly.
Disabling Windows Aero™ may also help correct this issue.

User’s Manual B-1

TECRA A10/S10/M10/SatellitePro S300

B-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix C

Wireless LAN

This appendix is intended to help you get your Wireless LAN network up
and running, with a minimum of parameters.

Card Specifications

Form Factor PCI Express Mini Card

Compatibility ■ IEEE 802.11 Standard for Wireless LANs

■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi
Alliance. The ‘Wi-Fi CERTIFIED’ logo is a
certification mark of the Wi-Fi Alliance.

Network Operating ■ Microsoft Windows Networking

System

Media Access ■ CSMA/CA (Collision Avoidance) with

Protocol Acknowledgment (ACK)

User’s Manual C-1

TECRA A10/S10/M10/SatellitePro S300

Radio Characteristics
Radio Characteristics of Wireless LAN module may vary according to:
■ Country/region where the product was purchased
■ Type of product
Wireless communication is often subject to local radio regulations.
Although Wireless LAN wireless networking products have been designed
for operation in the license-free 2.4GHz and 5GHz band, local radio
regulations may impose a number of limitations to the use of wireless
communication equipment.
Refer to the “Information sheet” for regulatory information that may apply in
your country/region.

Radio Frequency ■ Band 5GHz (5150-5850 MHz)

(Revision a and n draft 2.0)
■ Band 2.4GHz (2400-2483.5 MHz)
(Revision b/g and n draft 2.0)
The range of the wireless signal is related to the transmit rate of the
wireless communication. Communications at lower transmit range may
travel larger distances.
■ The range of your wireless devices can be affected when the antennas
are placed near metal surfaces and solid high-density materials.
■ Range is also impacted due to “obstacles” in the signal path of the radio
that may either absorb or reflect the radio signal.

Supported Frequency Sub-bands

Subject to the radio regulations that apply in the countries/regions, your
Wireless LAN module may support a different set of 5 GHz/2.4 GHz
channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office
for information about the radio regulations that apply in the countries/
regions.

C-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

2.4GHz Band Channels Sets

(Wireless IEEE 802.11 Revision b, g and n draft 2.0)

Frequency Range 2400-2497 MHz

Channel ID

1 2412

2 2417

3 2422

4 2427

5 2432

6 2437

7 2442

8 2447

9 2452

10 2457*1

11 2462

12 2467*2

13 2472*2

14 2482*2
*1 Factory-set default channels
*2 The band width and the channel which can be used depends on the
installed wireless LAN module. And the approved channels on using are
different at each country or region. When using these channels in any
country or region, refer to the addendum sheet which is Approved Countries/
Regions for use. The channel configuration is managed as follows:
■ For wireless clients that operate in a Wireless LAN Infrastructure, the
Wireless LAN module will automatically start operation at the channel
identified by the Wireless LAN Access Point. When roaming between
different access points the station can dynamically switch to another
channel if required.
■ For Wireless LAN modules installed in wireless clients that operating in
a peer-to-peer mode, the module will use the default channel 10.
■ In a Wireless LAN Access Point, the Wireless LAN module will use the
factory-set default channel (printed in bold), unless the LAN
Administrator selected a different channel when configuring the
Wireless LAN Access Point device.

User’s Manual C-3

TECRA A10/S10/M10/SatellitePro S300

5GHz Band Channels Sets

(Wireless IEEE 802.11 Revision a and n draft 2.0)

Frequency Range 5150-5850 MHz

Channel ID
34 5170*2
36 5180*2
38 5190*2
40 5200*2
42 5210*2
44 5220*2
46 5230*2
48 5240*2
52 5260*2
56 5280*2
60 5300*2
64 5320*2
100 5500*2
104 5520*2
108 5540*2
112 5560*2
116 5580*2
120 5600*2
124 5620*2
128 5640*2
132 5660*2
136 5680*2
140 5700*2
149 5745*2
153 5765*2
157 5785*2
161 5805*2
165 5825*2

C-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

*1 Factory-set default channels

*2 The channel which can be used depends on the installed wireless LAN
module. And the approved channels on using are different at each country
or region. When using these channels in any country or region, refer to the
addendum sheet which is Approved Countries/Regions for use. The
channel configuration is managed as follows:
■ For wireless clients that operate in a Wireless LAN Infrastructure, the
Wireless LAN module will automatically start operation at the channel
identified by the Wireless LAN Access Point. When roaming between
different access points the station can dynamically switch to another
channel if required.
■ For Wireless LAN modules installed in wireless clients that operating in
a peer-to-peer mode, the module will use the default channel 10.
■ In a Wireless LAN Access Point, the Wireless LAN module will use the
factory-set default channel (printed in bold), unless the LAN
Administrator selected a different channel when configuring the
Wireless LAN Access Point device.

User’s Manual C-5

TECRA A10/S10/M10/SatellitePro S300

C-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix D

Bluetooth wireless technology

Interoperability

Bluetooth Adaptor from TOSHIBA are designed to be interoperable with

any product with Bluetooth wireless technology that is based on Frequency
Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:
■ Bluetooth Specification Ver. 2.1+EDR, as defined and approved by The
Bluetooth Special Interest Group.
■ Logo certification with Bluetooth wireless technology as defined by The
Bluetooth Special interest Group.
■ When you use Bluetooth Adaptor from TOSHIBA close to 2.4 GHz
Wireless LAN devices, Bluetooth transmissions might slow down or
cause errors. If you detect certain interference while you use Bluetooth
Adaptor from TOSHIBA, always change the frequency, move your
computer to the area outside of the interference range of 2.4 GHz
Wireless LAN devices (40 meters/43.74 yards or more) or stop
transmitting from your computer. Please visit the following TOSHIBA
PC product support website.
■ Bluetooth and Wireless LAN devices operate within the same radio
frequency range and may interfere with one another. If you use
Bluetooth and Wireless LAN devices simultaneously, you may
occasionally experience a less than optimal network performance or
even lose your network connection.
If you should experience any such problem, immediately turn off either
one of your Bluetooth or Wireless LAN.
Please visit the following TOSHIBA PC product support website.

TOSHIBA PC product support website.

In Europe visit
http://www.toshiba-europe.com/computers/tnt/bluetooth.htm
In the United States visit
http://www.pc.support.global.toshiba.com

User’s Manual D-1

TECRA A10/S10/M10/SatellitePro S300

Bluetooth wireless technology and your Health

The products with Bluetooth wireless technology, like other radio devices,
emit radio frequency electromagnetic energy. The level of energy emitted
by devices with Bluetooth wireless technology however is far much less
than the electromagnetic energy emitted by wireless devices like for
example mobile phones.
Because products with Bluetooth wireless technology operate within the
guidelines found in radio frequency safety standards and
recommendations, TOSHIBA believes Bluetooth wireless technology is
safe for use by consumers. These standards and recommendations reflect
the consensus of the scientific community and result from deliberations of
panels and committees of scientists who continually review and interpret
the extensive research literature.
In some situations or environments, the use of Bluetooth wireless
technology may be restricted by the proprietor of the building or responsible
representatives of the organization. These situations may for example
include:
■ Using the equipment with Bluetooth wireless technology on board of
airplanes, or
■ In any other environment where the risk of interference to other devices
or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices
in a specific organization or environment (e.g. airports), you are
encouraged to ask for authorization to use the device with Bluetooth
wireless technology prior to turning on the equipment.

Regulatory statements
General
This product complies with any mandatory product specification in any
country/region where the product is sold. In addition, the product complies
with the following.
European Union (EU) and EFTA
This equipment complies with the R&TTE directive 1999/5/EC and has
been provided with the CE mark accordingly.
Canada - Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of this device.
The term “IC” before the equipment certification number only signifies that
the Industry Canada technical specifications were met.

D-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

USA-Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by tuning the equipment off and on, the
user is encouraged to try and correct the interference by one or more of the
following measures:
■ Reorient or relocate the receiving antenna
■ Increase the distance between the equipment and the receiver.
■ Connect the equipment to outlet on a circuit different from that to which
the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
TOSHIBA is not responsible for any radio or television interference caused
by unauthorized modification of the devices included with this Bluetooth
Adaptor from TOSHIBA, or the substitution or attachment of connecting
cables and equipment other than specified by TOSHIBA.
The correction of interference caused by such unauthorized modification,
substitution or attachment will be the responsibility of the user.

Caution: Exposure to Radio Frequency Radiation

The radiated output power of the Bluetooth Adaptor from TOSHIBA is far
below the FCC radio frequency exposure limits. Nevertheless, the
Bluetooth Adaptor from TOSHIBA shall be used in such a manner that the
potential for human contact during normal operation is minimized.
The installer of this radio equipment must ensure that the antenna is
located or pointed such that it does not emit RF field in excess of Health
Canada limits for the general population; consult Safety Code 6, obtainable
from Health Canada’s website www.hc-sc.gc.ca/rpb.

User’s Manual D-3

TECRA A10/S10/M10/SatellitePro S300

Taiwan

Article 12 Without permission granted by the DGT or NCC, any

company, enterprise, or user is not allowed to change
frequency, enhance transmitting power or alter original
characteristic as well as performance to an approved low
power radio-frequency devices.
Article 14 The low power radio-frequency devices shall not influence
aircraft security and interfere legal communications; If found,
the user shall cease operating immediately until no
interference is achieved.
The said legal communications means radio communications
is operated in compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptible
with the interference from legal communications or ISM radio
wave radiated devices.

Using Bluetooth Adaptor from TOSHIBA equipment in Japan

In Japan, the frequency bandwidth of 2,400 - 2,483.5 MHz for second
generation low-power data communication systems such as this equipment
overlaps that of mobile object identification systems (premises radio station
and specified low-power radio station).
1. Sticker
Please put the following sticker on computer incorporating this product.

The frequency bandwidth of this equipment may operate

within the same range as industrial devices, scientific
devices, medical devices, microwave ovens, licensed radio
stations and non-licensed specified low-power radio stations
for mobile object identification systems (RFID) used in
factory production lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not
interfere with any of the equipment listed above.
2. If this equipment causes RF interference to other radio
stations, promptly change the frequency being used,
change the location of use, or turn off the source of
emissions.
3. Contact TOSHIBA Direct PC if you have problems with
interference caused by this product to Other Radio Stations.

D-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

2. Indication
The indication shown below appears on this equipment.

(1) 2.4: This equipment uses a frequency of 2.4 GHz.

(2) FH: This equipment uses FH-SS modulation.
(3) 1: The interference range of this equipment is less than 10 m.
(4) This equipment uses a frequency bandwidth from
2,400 MHz to 2,483.5 MHz.
It is impossible to avoid the band of mobile object
identification systems.
3. TOSHIBA Direct PC
Monday - Friday : 10:00-17:00
Toll Free Tel : 0120-15-1048
Direct Dial : 03-3457-4850
FAX : 03-3457-4868

Device Authorization
This device obtains the Technical Conditions Compliance Approval, and it
belongs to the device class of radio equipment of low-power data
communication system radio station stipulated in the Telecommunications
Business Law.
The Name of the radio equipment: EYTFXCS
JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS
EQUIPMENT
Approval Number: D07-0040001
The following restrictions apply:
Do not disassemble or modify the device.
Do not install the embedded wireless module into other device.

User’s Manual D-5

TECRA A10/S10/M10/SatellitePro S300

D-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix E

AC Power Cord and Connectors

The power cord’s AC input plug must be compatible with the various
international AC power outlets and the cord must meet the standards for
the country/region in which it is used. All cords must meet the following
specifications:

Length: Minimum 1.7 meters

Wire size: Minimum 0.75 mm2
Current rating: Minimum 2.5 amperes
Voltage rating: 125 or 250 VAC
(depending on country/region’s power standards)

Certification agencies

U.S. and Canada: UL listed and CSA certified

No. 18 AWG, Type SVT or SPT-2
Australia: AS
Japan: DENANHO
Europe:
Austria: OVE Italy: IMQ
Belgium: CEBEC The Netherlands: KEMA
Denmark: DEMKO Norway: NEMKO
Finland: FIMKO Sweden: SEMKO
France: LCIE Switzerland: SEV
Germany: VDE United Kingdom: BSI
In Europe, two conductors power cord must be VDE type, H05VVH2-F or
H03VVH2-F and for three conductors power cord must be VDE type,
H05VV-F.

User’s Manual E-1

TECRA A10/S10/M10/SatellitePro S300

For the United States and Canada, two pin plug configuration must be a
2-15P (250V) or 1-15P (125V) and three pin plug configuration must be
6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical
code handbook and the Canadian Electrical Code Part II.
The following illustrations show the plug shapes for the U.S.A. and Canada,
the United Kingdom, Australia and Europe.

United Kingdom
USA

UL approved
BS approved

Australia Europe

AS approved
Approved by the
appropriate agency
Canada

CSA approved

E-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix F

TOSHIBA Anti-theft Protection Timer

This feature allows you to set up a timer-activated BIOS password that will
prevent unauthorised system access in the event of theft.
When the time limit is exceeded, you are required to provide the Password
or fingerprint authentication for the BIOS and Hard Disk Drive to gain
access to the system.
To set permissions and limits for the TOSHIBA Anti-theft Protection Timer
please use the TOSHIBA Password Utility.
The settings can only be activated or modified by a user with supervisor
authority. If the supervisor password is not set, click on the Set button in
Supervisor Password from the supervisor tab in TOSHIBA Password
Utility and set the password on the dialog screen that appears.
Then, click on the Set button in TOSHIBA Anti-theft Protection Timer.
Take the following action if the set limit is exceeded.
■ If the Supervisor Password is registered but the User Password is not,
enter the Supervisor Password to boot up the computer.
■ If both the Supervisor Password and the User Password are registered,
enter either the Supervisor Password, the User Password or the
fingerprint authentication to boot up the computer.
■ The limit counts the number of days from the last time Windows is
logged on till the next time the computer is booted up. The range can
be set from 1 to 28 days.
■ Authentication is required if the computer’s clock is significantly
modified.
■ If the Supervisor Password is deleted, this function becomes disabled.

User’s Manual F-1

TECRA A10/S10/M10/SatellitePro S300

F-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix G

TOSHIBA PC Health Monitor

The TOSHIBA PC Health Monitor software program monitors computer

system functions such as power consumption, the cooling system and HDD
Drop sensor. It alerts users of specific system conditions via pop-up
messages. It also tracks the usage of the computer and related devices,
logging the service relevant information on the computer’s hard disk drive.
The collected information includes device operation time and number of
actuations or status changes (i.e.: number of power button and FN key
combination uses, AC adaptor, battery, LCD, fan, HDD, sound volume,
wireless communication switch, TOSHIBA Express Port Replicator and
USB information), date of initial system use, and also computer and device
usage (i.e.: power settings, battery temperature and recharging, CPU,
memory, backlight illumination time, and temperatures for various devices).
The stored data uses a very small portion of the total hard disk capacity,
approximately 3MB or less per year.
This information is used to identify and provide a notification of system
conditions which may effect the performance of your Toshiba computer. It
may also be used to help diagnose problems should the computer require
service by Toshiba or Toshiba’s authorized service providers. Additionally,
Toshiba may also use this information for quality assurance analysis.
Subject to the use restrictions above, the HDD data logged may be
transferred to entities located outside of your country or region of residence
(e.g., European Union). Those countries may or may not have the same
data protection laws or data protection levels as required by your home
country or region.
Once enabled, you may disable the TOSHIBA PC Health Monitor at any
time by uninstalling the software via Uninstall a program in the Control
Panel. Doing so will automatically delete all collected information from the
HDD.
The TOSHIBA PC Health Monitor software does not extend or modify
Toshiba’s obligations under its standard limited warranty in any way.
Toshiba’s standard limited warranty terms and limitations apply.

User’s Manual G-1

TECRA A10/S10/M10/SatellitePro S300

Starting the TOSHIBA PC Health Monitor

The TOSHIBA PC Health Monitor can be started using the following
methods:
■ Double click TOSHIBA PC Health Monitor in the Welcome Center.
■ Click Start -> All Programs -> TOSHIBA -> Utilities -> PC Health
Monitor.

■ Click the icon ( ) in the notification area, then click the “TOSHIBA
PC Health Monitor is not enabled. Please click here
for more details.” message when it is displayed. (*)
No matter which method is used, the TOSHIBA PC Health Monitor
explanation screen will be displayed.
Clicking “Next” will display the “TOSHIBA PC Health Monitor
Software Notice & Acceptance” screen. Please carefully read the
information displayed. Selecting “Enable this software program now” and
clicking “OK” will enable the program. By enabling the TOSHIBA PC Health
Monitor software, you agree with these terms and conditions and to the use
and sharing of the collected information. Once the program is enabled, the
TOSHIBA PC Health Monitor screen is displayed, and the program will
begin monitoring system functions and collecting information.
(*) This message will no longer be displayed after clicking “Enable this
software program now” or “Disable this software program now” on the
“TOSHIBA PC Health Monitor Software Notice & Acceptance”
screen.

If a TOSHIBA PC Health Monitor message is displayed.

A message will be displayed if any changes which may interfere with the
operation of the program are detected. Follow the instructions displayed on
screen in the message. However, if the following special message is
displayed, carry out the procedures listed below.
If the “It is possible that the PC cooling performance has
decreased. Please click [OK] to run the TOSHIBA Cooling
Performance Diagnostic Tool to check the cooling
performance of your PC.” message is displayed.
1. Click “OK” to start the “TOSHIBA Cooling Performance Diagnostic Tool”.
2. If the “It is possible that the PC cooling performance
has decreased. Please clean the cooling module
according to the instructions in your PC User’s
Guide.” message is displayed after running the “TOSHIBA Cooling
Performance Diagnostic Tool”, the cooling module requires cleaning.
Refer to the Cleaning the cooling module section, in this chapter.
3. After cleaning the cooling module, run the “TOSHIBA Cooling
Performance Diagnostic Tool” again.
Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA
Cooling Performance Diagnostic Tool.

G-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

4. If the “Please click [OK] to run the TOSHIBA Cooling

Performance Diagnostic Tool to check the cooling
performance of your PC.” message is still displayed after running
the “TOSHIBA Cooling Performance Diagnostic Tool” in step 3, it is
recommended you turn off the computer and contact TOSHIBA support.

Cleaning the cooling module

This section explains how to clean the cooling module.
If you use the computer for a long period, the inside of the computer may
become hot. Always allow the computer to cool to room temperature
before you clean the cooling module.
To clean the cooling module, follow the steps detailed below:
1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).
2. Remove the AC adaptor and all cables and peripherals connected to
the computer.
3. Close the display panel and turn the computer upside down.
4. Remove the battery pack (refer to the Replacing the battery pack
section in Chapter 6, Power and Power-Up Modes, if required).
5. Using a thin-tipped tool, push on the hole in the edge of the Cooling
module cover and slide it in the direction of the arrow to remove.

Cooling module cover

Hole

Figure G-1 Removing the cooling module cover

6. Lift the plastic film and clean the cooling module using a vacuum
cleaner or other cleaning tool.
Do not use a ball pen, cotton swap or similar to remove dust. If these touch
the inside of the computer, it could be damaged or become clogged,
leading to further problems.

User’s Manual G-3

TECRA A10/S10/M10/SatellitePro S300

Plastic film

Figure G-2 Lift the plastic film

7. Slide the Cooling module cover back into place on the computer to
reattach.
8. Install the battery pack (refer to the Replacing the battery pack section
in Chapter 6, Power and Power-Up Modes, if required).
9. Turn your computer over.

G-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix H

Legal Footnotes

This chapter states the Legal Footnotes information applicable to TOSHIBA

computers. In the text in this manual, *XX is used to show which Legal
Footnotes description is related to TOSHIBA computers.
Description(s) related to this computer are marked with a blue *XX in this
manual. Clicking on *XX will display the related description.

Non-applicable Icons*1
Certain computer chassis are designed to accommodate all possible
configurations for an entire product series. Therefore, please be aware that
your selected model may not have all the features and specifications
corresponding to all of the icons or switches shown on the computer
chassis.

CPU*2
Central Processing Unit (“CPU”) Performance Legal Footnotes.
CPU performance in your computer product may vary from specifications
under the following conditions:
■ use of certain external peripheral products
■ use if battery power instead of AC power
■ use of certain multimedia, computer generated graphics or video
applications
■ use of standard telephone lines or low speed network connections
■ use of complex modeling software, such as high end computer aided
design applications
■ use of several applications or functionalities simultaneously
■ use of computer in areas with low air pressure
(high altitude >1,000 meters or >3,280 feet above sea level)
■ use of computer at temperatures outside the range of 5°C to 30°C
(41°F to 86°F) or >25°C (77°F) at high altitude (all temperature
references are approximate and may vary depending on the specific
computer model - please refer to your computer documentation or visit
the Toshiba website at www.pcsupport.toshiba.com for details).

User’s Manual H-1

TECRA A10/S10/M10/SatellitePro S300

CPU performance may also vary from specifications due to design

configuration.
Under some conditions, your computer product may automatically
shut-down. This is a normal protective feature designed to reduce the risk
of lost data or damage to the product when used outside recommended
conditions. To avoid risk of lost data, always make back-up copies of data
by periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions in your product documentation.
Contact Toshiba technical service and support, refer to TOSHIBA support
section in Chapter 8, Troubleshooting for more information.

64-Bit Computing
64-bit processors are designed to take advantage of 32 and 64 bit
computing.
64-bit computing requires that the following hardware and software
requirements are met:
■ 64-bit Operating System
■ 64-bit CPU, Chipset and BIOS (Basic Input/Output System)
■ 64-bit Device drivers
■ 64-bit applications
Certain device drivers and/or applications may not be compatible with a
64-bit CPU and therefore may not function properly. A 32-bit version of the
operating system is preinstalled on your computer unless explicitly stated
that the operating system is 64-bit.

Memory (Main System)*3

Part of the main system memory may be used by the graphics system for
graphics performance and therefore reduce the amount of main system
memory available for other computing activities. The amount of main
system memory allocated to support graphics may vary depending on the
graphics system, applications utilized, system memory size and other
factors. For computer’s configured with 4 GB of system memory, the full
system memory space for computing activities will be considerably less and
will vary by model and system configuration.

H-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Battery Life*4
Battery life may vary considerably depending on product model,
configuration, applications, power management settings and features
utilized, as well as the natural performance variations produced by the
design of individual components. Published battery life numbers are
achieved on select models and configurations tested by Toshiba at the time
of publication. Recharge time varies depending on usage. Battery may not
charge while computer is consuming full power.
After going through many charge and discharge cycles, the battery will lose
its ability to perform at maximum capacity and will need to be replaced.
This is a normal phenomenon for all batteries. To purchase a new battery
pack, see the accessories information that is shipped with your computer.

Hard Disk Drive (HDD) Capacity*5

1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10.
The computer operating system, however, reports storage capacity using
powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and
therefore shows less storage capacity. Available storage capacity will also
be less if the product includes one or more pre-installed operating systems,
such as Microsoft Operating System and/or pre-installed software
applications, or media content. Actual formatted capacity may vary.

LCD*6
Over a period of time, and depending on the usage of the computer, the
brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology.
Maximum brightness is only available when operating in AC power mode.
Screen will dim when the computer is operated on battery power and you
may not be able to increase the brightness of the screen.

Graphics Processor Unit (“GPU”)*7

Graphics processor unit (“GPU”) performance may vary depending on
product model, design configuration, applications, power management
settings and features utilized. GPU performance is only optimized when
operating in AC power mode and may decrease considerably when
operating in battery power mode.
Total Available Graphics Memory is the total of, as applicable, Dedicated
Video Memory, System Video Memory and Shared System Memory.
Shared System Memory will vary depending on system memory size and
other factors.

User’s Manual H-3

TECRA A10/S10/M10/SatellitePro S300

Wireless LAN*8
The transmission speed over the wireless LAN and the distance over which
wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
The actual transmission speed will be lower than the theoretical maximum
speed.

The wireless adapter is based on a draft 2.0 release version of the IEEE
802.11n specification and; may not be full compatible with, or support some
feature (e.g., security) of, certain Wi-Fi equipment.

Copy Protection*9
Applicable copy protection standards included in certain media may
prevent or limit recording or viewing of the media.

Images*10
All images are simulated for purposes of illustration.

H-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Appendix I

If your computer is stolen

Always take care of your computer and try to prevent it from being stolen.
You are the owner of a valuable technical device, which may be highly
attractive to thieves, so please do not leave it unattended in a public place.
To further help protect against theft, security cables can be bought for use
with your notebook when it is being used at home or in the office.
Make a note of your computer’s machine type, model number, and serial
number, and put it in a safe place. You will find this information on the
underside of your notebook. Please also keep the receipt of the computer
you purchased.

Should your computer be stolen, however, we’ll help you try to find it.
Before contacting TOSHIBA, please prepare the following information
which is necessary to uniquely identify your computer:
■ In which country was your computer stolen?
■ What type of machine do you have?
■ What was the model number (PA number)?
■ What was the serial number (8 digits)?
■ When was it stolen, i.e. date?
■ What is your address, phone, and fax number?
To register the theft on paper, please follow these procedures:
■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below.
■ Attach a copy of your receipt showing where your computer was
purchased.
■ Either fax or send the receipt and registration form to the address below.
To register the theft online, please follow these procedures:
■ Visit www.toshiba-europe.com on the Internet. In the product area,
choose Computer Systems.
■ In the Computer Systems page, open the Support & Downloads menu
and choose the Stolen Units Database option.
Your entries are used to track your computer at our service points.

User’s Manual I-1

TECRA A10/S10/M10/SatellitePro S300

TOSHIBA Theft Registration

Send to: TOSHIBA Europe GmbH
Technical Service and Support
Leibnizstr. 2
93055 Regensburg
Germany
Fax number: +49 (0) 941 7807 921
Country stolen:

Machine type:
(e.g. TECRA A10/S10/
M10/SatellitePro S300)

Model number:
(e.g. PSA50 YXT)

Serial number:
(e.g. 12345678G)

Date stolen: Year Month Day

Owner’s details
Last name, first name:
Company:
Street:
Postal Code/City:
Country:
Phone:
Fax:

I-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Glossary
The terms in this glossary cover topics related to this manual. Alternate
naming is included for reference.

Abbreviations
AC: Alternating current
ACPI: Advanced Configuration and Power Interface
AMT: Intel Active Management Technology
ASCII: American Standard Code for Information Interchange
BIOS: basic input/output system
bps: bits per second
CD: compact disc
CD-ROM: Compact Disc Read-Only Memory
CD-RW: Compact Disc-ReWritable
CMOS: complementary metal-oxide semiconductor
CPU: central processing unit
CRT: cathode ray tube
DC: direct current
DDC: display data channel
DDR: double data rate
DIMM: dual inline memory module
DVD: digital versatile disc
DVD-R: Digital Versatile Disc-Recordable
DVD-RAM: Digital Versatile Disc-Random Access Memory
DVD-R (Dual Layer): Digital Versatile Disc Recordable Dual Layer
DVD-ROM: Digital Versatile Disc-Read Only Memory
DVD-RW: Digital Versatile Disc-ReWritable
DVD+R (Double Layer): Digital Versatile Disc Recordable Double Layer
eSATA: external Serial ATA
FDD: floppy diskette drive
FIR: fast infrared
GB: gigabyte
HDD: hard disk drive
IDE: integrated drive electronics
IEEE: Institute of Electrical and Electronics Engineers
IMSM: Intel Matrix Storage Manager
I/O: input/output
IRQ: interrupt request

User’s Manual Glossary-1

TECRA A10/S10/M10/SatellitePro S300

KB: kilobyte
LAN: local area network
LCD: liquid crystal display
LED: light emitting diode
MB: megabyte
MMC: multi media card
OCR: optical character recognition (reader)
PC: personal computer
PCI: peripheral component interconnect
RAM: random access memory
RGB: red, green, and blue
ROM: read only memory
RTC: real time clock
S/P DIF: Sony/Philips Digital Interface Format
SDRAM: synchronous dynamic random access memory
SLI: Scalable Link Interface
SO-DIMM: small-outline dual in line memory module
SSD: Solid state drive
TFT: thin-film transistor
USB: Universal Serial Bus
UXGA: ultra extended graphics array
VGA: video graphics array
WAN: wide area network
WSXGA: wide super extended graphics array
WSXGA+: wide super extended graphics array plus
WUXGA: Wide Ultra Extended Graphics Array
WXGA: wide extended graphics array
WXGA+: wide extended graphics array plus
XGA: extended graphics array

A
AccuPoint: A pointing device integrated into the TOSHIBA computer
keyboard.
adaptor: A device that provides a compatible connection between two
units. For example, the computer’s internal display adapter receives
information from the software and translates it into images on the
screen. An adapter can take a number of forms, from a
microprocessor to a simple connector: An intelligent adapter (one
that is capable of doing some processing) may also be called a
controller.

Glossary-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

alphanumeric: Keyboard characters including letters, numbers and other

symbols, such as punctuation marks or mathematical symbols.
alternating current (AC): Electric current that reverses its direction of flow
at regular intervals.
analog signal: A signal whose characteristics such as amplitude and
frequency vary in proportion to (are an analog of) the value to be
transmitted. Voice communications are analog signals.
application: A group of programs that together are used for a specific task
such as accounting, financial planning, spreadsheets, word
processing and games.
ASCII: American Standard Code for Information Interchange. ASCII code is
a set of 256 binary codes that represent the most commonly used
letters, numbers, and symbols.
asynchronous: Lacking regular time relationship. As applied to computer
communications, asynchronous refers to the method of transmitting
data that does not require a steady stream of bits to be transmitted
at regular time intervals.

B
backup: A copy of a file, usually on a removable disk, kept in case the
original file is lost or damaged.
binary: The base two number system composed of zeros and ones (off or
on), used by most digital computers. The right-most digit of a binary
number has a value of 1, the next a value of 2, then 4, 8, 16, and so
on. For example, the binary number 101 has a value of 5.
See also ASCII.
BIOS: Basic Input/Output System. The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from “binary digit,” the basic unit of information used by the
computer. It is either zero or one. Eight bits is one byte.
See also byte.
Bluetooth: A short-range radio technology designed to simplify wireless
communication among computers, communication devices and the
Internet.
board: A circuit board. An internal card containing electronic components,
called chips, which perform a specific function or increase the
capabilities of the system.
boot: Short for bootstrap. A program that starts or restarts the computer.
The program reads instructions from a storage device into the
computer’s memory.
boot disk: See system disk.
bootable disk: See system disk.
bps: Bits per second. Typically used to describe the data transmission
speed of a modem.

User’s Manual Glossary-3

TECRA A10/S10/M10/SatellitePro S300

buffer: The portion of the computer’s memory where data is temporarily

stored. Buffers often compensate for differences in the rate of flow
from one device to another.
bus: An interface for transmission of signals, data or electric power.
byte: The representation of a single character. A sequence of eight bits
treated as a single unit; also the smallest addressable unit within the
system.

C
cache memory: A section of very fast memory in which frequently used
information is duplicated for quick access. Accessing data from
cache is faster than accessing it from the computer’s main memory.
See also L1 cache, L2 cache.
capacity: The amount of data that can be stored on a magnetic storage
device such as a floppy diskette or hard disk drive. It is usually
described in terms of kilobytes (KB), where one KB = 1024 bytes,
megabytes (MB), where one MB = 1024 KB and gigabytes (GB),
where one GB = 1024 MB.
CardBus: An industry standard bus for 32-bit PC Cards.
CD: An individual compact disc. See also CD-ROM.
CD-R: A Compact Disc-Recordable disc can be written once and read
many times. See also CD-ROM.
CD-ROM: A Compact Disc Read-Only Memory is a high capacity disc that
can be read from but not written to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read data from the disc.
CD-RW: A Compact Disc-ReWritable disc can be rewritten many times.
See also CD-ROM.
character: Any letter, number, punctuation mark, or symbol used by the
computer. Also synonymous with byte.
chassis: The frame containing the computer.
chip: A small semiconductor containing computer logic and circuitry for
processing, memory, input/output functions and controlling other
chips.
click: To press and release the pointing device’s primary button without
moving the pointing device. In the Windows operating system, this
refers to the pointing device’s left button, unless otherwise stated.
See also double-click.
CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit
fabricated on a silicon wafer that requires very little power.
Integrated circuits implemented in CMOS technology can be tightly
packaged and are highly reliable.
cold start: Starting a computer that is currently off (turning on the power).

Glossary-4 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

COM1, COM2, COM3 and COM4: The names assigned to the serial and
communication ports.
commands: Instructions you enter at the terminal keyboard that direct the
actions of the computer or its peripheral devices.
compatibility: 1) The ability of one computer to accept and process data in
the same manner as another computer without modifying the data
or the media upon which it is being transferred.
2) the ability of one device to connect to or communicate with
another system or component.
components: Elements or parts (of a system) which make up the whole
(system).
computer program: A set of instructions written for a computer that enable
it to achieve a desired result.
computer system: A combination of hardware, software, firmware, and
peripheral components assembled to process data into useful
information.
configuration: The specific components in your system (such as the
terminal, printer, and disk drives) and the settings that define how
your system works. You use the HW Setup program to control your
system configuration.
controller: Built-in hardware and software that controls the functions of a
specific internal or peripheral device (e.g. keyboard controller).
CPU: Central Processing Unit. The portion of the computer that interprets
and executes instructions.
CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a
fluorescent screen-producing luminous spots. An example is the
television set.
cursor: A small, blinking rectangle or line that indicates the current position
on the display screen.

D
data: Information that is factual, measurable or statistical that a computer
can process, store, or retrieve.
data bits: A data communications parameter controlling the number of bits
(binary digits) used to make up a byte. If data bits = 7 the computer
can generate 128 unique characters. If data bits = 8 the computer
can generate 256 unique characters.
DC: Direct Current. Electric current that flows in one direction. This type of
power is usually supplied by batteries.
default: The parameter value automatically selected by the system when
you or the program do not provide instructions. Also called a preset
value.
delete: To remove data from a disk or other data storage device.
Synonymous with erase.

User’s Manual Glossary-5

TECRA A10/S10/M10/SatellitePro S300

device driver: A program (called a “driver”) that permits a computer to

communicate with a device.
dialog box: A window that accepts user input to make system settings or
record other information.
disable: To turn a computer option off. See also enable.
disk drive: The device that randomly accesses information on a disk and
copies it to the computer’s memory. It also writes data from memory
to the disk. To accomplish these tasks, the unit physically rotates the
disk at high speed past a read-write head.
disk storage: Storing data on magnetic disk. Data is arranged on
concentric tracks much like a phonograph record.
display: A CRT, LCD, or other image producing device used to view
computer output.
documentation: The set of manuals and/or other instructions written for
the users of a computer system or application. Computer system
documentation typically includes procedural and tutorial information
as well as system functions.
double click: To press and release the pointing device’s primary button
rapidly twice without moving the pointing device. In the Windows
operating system, this refers to the pointing device’s left button,
unless otherwise stated.
driver: A software program, generally part of the operating system, that
controls a specific piece of hardware (frequently a peripheral device
such as a printer or mouse).
DVD: An individual digital versatile (or video) disc. See also DVD-ROM.
DVD-R (+R, -R): A Digital Versatile Disc-Recordable disk can be written
once and read many times. The DVD-R drive uses a laser to read
data from the disc.
DVD-RAM: A Digital Versatile Disc-Random Access Memory is a
high-capacity, high performance disc that lets you store large
volumes of data. The DVD-ROM drive uses a laser to read data
from the disc.
DVD-ROM: A Digital Versatile Disc-Read Only Memory is a high capacity,
high performance disc suitable for play back of video and other
high-density files. The DVD-ROM drive uses a laser to read data
from the disc.
DVD-RW (+RW, -RW): A Digital Versatile Disc-ReWritable disc can be
rewritten many times.

Glossary-6 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

E
echo: To send back a reflection of the transmitted data to the sending
device. You can display the information on the screen, or output it to
the printer, or both. When a computer receives back data it
transmitted to a CRT (or other peripheral device) and then transmits
the data to printer, the printer is said to echo the CRT.
enable: To turn on a computer option. See also disable.
erase: See delete.
escape: 1) A code (ASCII code 27), signaling the computer that what
follows are commands; used with peripheral devices such as
printers and modems.
2) A means of aborting the task currently in progress.
escape guard time: A time before and after an escape code is sent to the
modem which distinguishes between escapes that are part of the
transmitted data, and escapes that are intended as a command to
the modem.
execute: To interpret and execute an instruction.

F
fast infrared: An industry standard that enables cableless infrared serial
data transfer at speeds of up to 4 Mbps.
file: A collection of related information; a file can contain data, programs,
or both.
fingerprint sensor: The fingerprint sensor compares and analyzes the
unique characteristics in a fingerprint.
firmware: A set of instructions built into the hardware which controls and
directs a microprocessor’s activities.
flash memory: Non-volatile memory that can be written to as well as read.
Information in flash memory remains whether or not the computer is
receiving power. This type of memory is used to retain your
fingerprint data. See also memory. Compare RAM and ROM.
floppy diskette: A removable disk that stores magnetically encoded data.
floppy diskette drive (FDD): An electromechanical device that reads and
writes to floppy diskettes.
folder: An icon in Windows used to store documents or other folders.
format: The process of readying a blank disk for its first use. Formatting
establishes the structure of the disk that the operating system
expects before it writes files or programs onto the disk.
function keys: The keys labeled F1 through F12 that tell the computer to
perform certain functions.

User’s Manual Glossary-7

TECRA A10/S10/M10/SatellitePro S300

G
gigabyte (GB): A unit of data storage equal to 1024 megabytes.
See also megabyte.
graphics: Drawings, pictures, or other images, such as charts or graphs,
to present information.

H
hard disk: A storage device composed of a rigid platter or platters that can
be magnetically coded with data. Hard disks hold much more
information than diskettes and are used for long-term storage of
programs and data. The primary (or only) hard disk in a computer is
usually fixed, but some computers have secondary hard disks that
are removable. By default, the hard disk is referred to as drive C.
hard disk drive (HDD): An electromechanical device that reads and writes
a hard disk. See also hard disk.
hardware: The physical electronic and mechanical components of a
computer system: typically, the computer itself, external disk drives,
etc. See also software and firmware.
hertz: A unit of wave frequency that equals one cycle per second.
host computer: The computer that controls, regulates, and transmits
information to a device or another computer.
hot key: The computer’s feature in which certain keys in combination with
the extended function key, FN, can be used to set system
parameters, such as speaker volume.
HW Setup: A TOSHIBA utility that lets you set the parameters for various
hardware components.

I
icon: A small graphic image displayed on the screen or in the indicator
panel. In Windows, an icon represents an object that the user can
manipulate.
i.LINK (IEEE1394): This port enables high-speed data transfer directly
from external devices such as digital video cameras.
input: The data or instructions you provide to a computer, communication
device or other peripheral device from the keyboard or external or
internal storage devices. The data sent (or output) by the sending
computer is input for the receiving computer.
instruction: Statements or commands that specify how to perform a
particular task.

Glossary-8 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

interface: 1) Hardware and/or software components of a system used

specifically to connect one system or device to another.
2) To physically connect one system or device to another to
exchange information.
3) The point of contact between user, the computer, and the
program, for example, the keyboard or a menu.
interrupt request: A signal that gives a component access to the
processor.
I/O: Input/output. Refers to acceptance and transfer of data to and from a
computer.
I/O devices: Equipment used to communicate with the computer and
transfer data to and from it.

K
K: Taken from the Greek word kilo, meaning 1000; often used as equivalent
to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
keyboard: An input device containing switches that are activated by
manually pressing marked keys. Each keystroke activates a switch
that transmits a specific code to the computer. For each key, the
transmitted code is, in turn, representative of the (ASCII) character
marked on the key.
kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte
and megabyte.

L
L1 cache: Level one cache. Memory cache built into the processor to help
improve processing speed. See also cache memory, L2 cache.
L2 cache: Memory cache installed on the motherboard to help improve
processing speed. It is slower than L1 cache and faster than main
memory. See also cache memory, L1 cache.
LAN: A group of computers or other devices dispersed over a relatively
limited area and connected by a communications link that enables
any device to interact with any other on the network.
Light Emitting Diode (LED): A semiconductor device that emits light when
a current is applied.
Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of
glass coated with transparent conducting material. The viewing-side
coating is etched into character forming segments with leads that
extend to the edge of the glass. Applying a voltage between the
glass sheets alters the brightness of the liquid crystal.

User’s Manual Glossary-9

TECRA A10/S10/M10/SatellitePro S300

M
main board: See motherboard.
megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also
kilobyte.
megahertz: A unit of wave frequency that equals 1 million cycles per
second. See also hertz.
memory: Typically refers to the computer’s main memory, where programs
are run and data is temporarily stored and processed. Memory can
be volatile and hold data temporarily, such as RAM, or it can be
nonvolatile and hold data permanently, such as ROM. A computer’s
main memory is RAM. See RAM, ROM.
menu: A software interface that displays a list of options on the screen.
Also called a screen.
microprocessor: A hardware component contained in a single integrated
circuit that carries out instructions. Also called the central
processing unit (CPU), one of the main parts of the computer.
mode: A method of operation, for example, the Shut Down Mode, Sleep
Mode or the Hibernation Mode.
modem: Derived from modulator/demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and
then converts modulated data (demodulates) to digital format where
received.
monitor: A device that uses rows and columns of pixels to display
alphanumeric characters or graphic images. See also CRT.
motherboard: A name sometimes used to refer to the main printed circuit
board in processing equipment. It usually contains integrated
circuits that perform the processor’s basic functions and provides
connectors for adding other boards that perform special functions.
MP3: An audio compression standard that enables high-quality
transmission and real-time playback of sound files.

N
network: A collection of computers and associated devices that are
connected by communications facilities. A network allows you to
share data and peripheral devices, such as printers, with other
users and to exchange electronic mail.
non-system disk: A disk for storing programs and data that cannot be
used to start the computer. Compare system disk.
nonvolatile memory: Memory that is capable of permanently storing
information. Turning the computer’s power off does not alter data
stored in nonvolatile memory.

Glossary-10 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

numeric keypad overlay: A feature that allows you to use certain keys on
the keyboard to perform numeric entry, or to control cursor and page
movement.

O
OCR: Optical Character Recognition (reader). A technique or device that
uses laser or visible light to identify characters and input them into a
storage device.
online state: A functional state of a peripheral device when it is ready to
receive or transmit data.
operating system: A group of programs that controls the basic operation
of a computer. Operating system functions include interpreting
programs, creating data files, and controlling the transmission and
receipt (input/output) of data to and from memory and peripheral
device.
output: The results of a computer operation. Output commonly indicates
data.
1) printed on paper, 2) displayed at a terminal, 3) sent through the
serial port of internal modem, or 4) stored on some magnetic media.

P
parallel: Processes that occur simultaneously. In communications,
it means the transmission of more than one bit of information at a
time. On your computer, the parallel port provides a parallel
communications interface between the computer and an
appropriate device. Compare serial.
parity: 1) The symmetrical relationship between two parameter values
(integers) both of which are either on or off; odd or even; 0 or 1.
2) In serial communications, an error detection bit that is added to a
group of data bits making the sum of the bits even or odd. Parity can
be set to none, odd, or even.
password: A unique string of characters used to identify a specific user.
The computer provides various levels of password protection such
as user and supervisor.
PC card: A credit-card-sized expansion card designed to increase the
capabilities of notebook computers. PC Cards provide functions
such as modem, fax/modem, hard disk drive, network adapter,
sound card, or SCSI adapter.
PCI: Peripheral Component Interconnect. An industry standard 32-bit bus.
peripheral: Any device, such as a printer or joystick, that is attached to the
computer and controlled by the computer’s CPU.
pixel: A picture element. The smallest dot that can be made on a display or
printer. Also called a pel.

User’s Manual Glossary-11

TECRA A10/S10/M10/SatellitePro S300

plug and play: A capability with Windows that enables the system to
automatically recognize connections of external devices and make
the necessary configurations in the computer.
pointing device: Any device, such as the Touch Pad or a mouse, that
enables you to move the cursor on the screen.
port: The electrical connection through which the computer sends and
receives data to and from devices or other computers.
Power Saver: A TOSHIBA utility that lets you set the parameters for
various power-saving functions.
program: A set of instructions a computer can execute that enables it to
achieve a desired result. See also application.
prompt: A message the computer provides indicating it is ready for or
requires information or an action from you.

R
Radio frequency interference (RFI) shield: A metal shield enclosing the
printed circuit boards of the printer or computer to prevent radio and
TV interference. All computer equipment generates radio frequency
signals. The FCC regulates the amount of signals a computing
device can allow past its shielding. A Class A device is sufficient for
office use. Class B provides a more stringent classification for home
equipment use. TOSHIBA portable computers comply with Class B
computing device regulations.
Random Access Memory (RAM): Volatile memory that can be written to
as well as read. Volatile here means that information in RAM is lost
when you turn off your computer. This type of memory is used for
your computer’s main memory. See also memory. Compare ROM.
resolution: A measure of the sharpness of the images that can be
produced by a printer or displayed on a screen. For a printer,
resolution is expressed in dots per inch (dpi). For a screen, it is
expressed as the number of pixels available horizontally and
vertically.
restart: Resetting a computer without turning it off (also called “warm boot”,
“soft reset” or “reboot”). See also boot.
RGB: Red, green, and blue. A device that uses three input signals, each
activating an electron gun for a primary additive color (red, green,
and blue) or port for using such a device. See also CRT.
RJ45: A modular LAN jack.
Read Only Memory (ROM): Non-volatile memory that can be read but not
written to. Non-volatile here means that information in ROM remains
whether or not the computer is receiving power. This type of
memory is used to store your computer’s BIOS, which is essential
instructions the computer reads when you start it up. See also
BIOS, memory. Compare RAM.

Glossary-12 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

S
S/P DIF: A standard of digital interface for audio.
SCSI: Small Computer System Interface is an industry standard interface
for connection of a variety of peripheral devices.
SD/SDHC Card: Secure Digital cards are flash memory widely used in a
variety of digital devices such as digital cameras and Personal
Digital Assistants.
serial: Processes that occur one at a time. In communications, it means
the transmission of one bit at a time sequentially over a single
channel. On your computer, the serial port provides a serial
interface between the computer and an appropriate device.
Compare parallel.
SIO: Serial Input/Output. The electronic methodology used in serial data
transmission.
soft key: Key combinations that emulate keys on the IBM keyboard,
change some configuration options, stop program execution, and
access the numeric keypad overlay.
software: The set of programs, procedures and related documentation
associated with a computer system. Specifically refers to computer
programs that direct and control the computer system’s activities.
See also hardware.
stop bit: One or more bits of a byte that follow the transmitted character or
group codes in asynchronous serial communications.
synchronous: Having a constant time interval between successive bits,
characters or events.
system disk: A diskette that contains the operating system files needed to
start the computer. Any diskette can be formatted as a system disk.
A system disk is also called a “bootable disk”, “boot disk” or a
“startup disk.” Compare non-system disk.

T
terminal: A typewriter-like keyboard and CRT display screen connected to
the computer for data input/output.
TFT display: A liquid crystal display (LCD) made from an array of liquid
crystal cells using active-matrix technology with thin film transistor
(TFT) to drive each cell.
Touch Pad: A pointing device integrated into the TOSHIBA computer palm
rest.

User’s Manual Glossary-13

TECRA A10/S10/M10/SatellitePro S300

U
USB: Universal Serial Bus. This serial interface lets you communicate with
several devices connected in a chain to a single port on the
computer.

V
VGA: Video Graphics Array is an industry standard video adaptor that lets
you run any popular software.
volatile memory: Random access memory (RAM) that stores information
as long as power is supplied to the computer.

W
warm start: Restarting or resetting a computer without turning it off.
Wi-Fi: A registered trademark term of the Wi-Fi Alliance that stands for
Wireless Fidelity, and is another term for the communication
protocol to permit an Ethernet connection using wireless
communication components.
window: A portion of the screen that can display its own application,
document or dialog box. Often used to mean a Microsoft Windows
window.
Wireless LAN: Local Area Network (LAN) through wireless
communication.
Wireless WAN: Wide Area Network (WAN) through wireless
communication.
write protection: A method for protecting a floppy diskette from accidental
erasure.

Glossary-14 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

Index

A Docking port, 2-7

Documentation list, 1-2
AC adaptor, 3-3
Dual Pointing Device
additional, 3-36
AccuPoint, 2-10, 4-2
connecting, 1-3
AccuPoint control buttons, 2-10
DC IN 15V jack, 2-6
Touch Pad, 2-10, 4-1, 8-16
ASCII characters, 5-7
Touch Pad control buttons, 2-10, 4-1
B Touch Pad location, 2-9
using, 4-1
Battery
DVD Super Multi drive
charging, 6-5
problems, 8-12
extending life, 6-7
using, 4-15
indicator, 2-12, 6-2
writing, 4-22
monitoring capacity, 6-6
DVD-ROM drive
real time clock, 3-3, 6-4
problems, 8-9
save mode, 3-7
using, 4-15
types, 6-3
DVD-ROM&CD-R/RW drive
Battery pack, 2-8, 3-2
problems, 8-10
additional, 6-1
using, 4-15
replacing, -xi, 6-8
writing, 4-19
Bluetooth, 3-6, 4-36
Bluetooth Stack for Windows by E
Toshiba, 3-12
Equipment checklist, 1-1
problems, 8-27
eSATA device, 3-30
Boot Priority, 7-3
eSATA/USB combo port, 2-3
Bridge media slot, 2-3, 3-19
problems, 8-21
indicator, 2-13
External monitor, 2-6, 3-28
using, 3-19
problems, 8-24
C F
Cleaning the computer, 4-39
Fingerprint Sensor
Cooling vents, 2-2
location, 2-9
D problems, 8-19
using, 4-3
DC IN indicator, 2-12, 6-3
Floppy diskette care, 4-29
Display, 3-4
FN + 1 (TOSHIBA Zooming Utility reduce),
automatic power off, 3-7
5-5
brightness down, 5-4
FN + 2 (TOSHIBA Zooming Utility enlarge),
brightness up, 5-4
5-5
controller, B-1
FN + Enter, 5-3
hinges, 2-9
FN + ESC (Mute), 5-3
opening, 1-6
FN + F1 (Lock), 5-3
screen, 2-9

User’s Manual Index-1

TECRA A10/S10/M10/SatellitePro S300

FN + F10 (Arrow mode), 5-3 HW Setup

FN + F11 (Numeric mode), 5-3 accessing, 7-1
FN + F12 (ScrLock), 5-3 Boot priority, 7-3
FN + F2 (Power Plan), 5-3 CPU, 7-6
FN + F3 (Sleep), 5-4 device config, 7-7
FN + F4 (Hibernate), 5-4 display, 7-2
FN + F5 (Output), 5-4 general, 7-2
FN + F6 (Brightness Down), 5-4 keyboard, 7-5
FN + F7 (Brightness Up), 5-4 LAN, 7-6
FN + F8 (Wireless), 5-4 USB, 7-7
FN + F9 (Touch Pad), 5-4 window, 7-1
FN + space (Zoom), 5-5
Function keys, 5-2 I
i.LINK, 2-4
G connecting, 3-32
Graphics controller, 3-4 disconnecting, 3-33
precautions, 3-31
H problems, 8-25
Hard disk drive, 3-3 Indicators, 2-12
automatic power off, 3-7
Hard Disk Drive/Optical Disc Drive K
indicator, 2-12 Keyboard, 5-1
HDD Protection, 4-41 emulating enhanced keyboard, 5-2
Heat dispersal, 3-8, 4-45 FN Sticky key, 5-5
Hibernation Mode, 3-8 Function keys F1...F12, 5-2
Hot keys, 3-6 Hot keys, 5-3
Brightness Down, 5-4 problems, 8-7
Brightness Up, 5-4 typewriter keys, 5-1
Hibernate, 5-4 Windows special keys, 5-5
Lock, 5-3 Keypad overlay, 3-7
Mute, 5-3 Arrow mode, 5-6
Output, 5-4 Numeric mode, 5-6
Power Plan, 5-3 temporarily using normal keyboard
Sleep, 5-4 (overlay on), 5-7
TOSHIBA Zooming Utility (enlarge), temporarily using overlay (overlay off),
5-5 5-7
TOSHIBA Zooming Utility (reduce), turning on the overlays, 5-6
5-5
Touch Pad, 5-4 L
Wireless, 5-4 LAN, 3-5, 4-37
Zoom, 5-5 active indicator, 2-6
cable types, 4-38
connecting, 4-38
disconnecting, 4-39
jack, 2-6
Link indicator, 2-6
problems, 8-26

Index-2 User’s Manual

 TECRA A10/S10/M10/SatellitePro S300

M Shut Down mode (Boot Mode), 1-7

Sleep Mode, 1-8
Media care, 4-28
System Auto Off, 6-13
Card care, 3-21
turning off, 1-7
CD/DVDs, 4-28
turning on, 1-7
Floppy diskettes, 4-29
Problems
Memory card care, 3-22
AC power, 8-5
Memory, 3-2
Additional memory module, 8-22
additional, 3-36
Analyzing the problem, 8-2
installing, 3-25
Battery, 8-6
problems, 8-22
Bluetooth, 8-27
removing, 3-27
Dual Pointing device, 8-16
Memory Stick, 3-20
DVD Super Multi drive, 8-12
inserting, 3-22
DVD-ROM drive, 8-9
problems, 8-15
DVD-ROM&CD-R/RW drive, 8-10
removing, 3-23
eSATA device, 8-21
Modem, 3-5
External monitor, 8-24
connecting, 4-33
Fingerprint Sensor, 8-19
disconnecting, 4-34
Hard disk drive, 8-8
jack, 2-5
Hardware and system checklist, 8-3
problems, 8-25
i.LINK (IEEE1394) device, 8-25
properties menu, 4-32
Internal display panel, 8-8
region selection, 4-31
Keyboard, 8-7
Moving the computer, 4-40
LAN, 8-26
MultiMediaCard, 3-20
Memory Stick, 8-15
inserting, 3-22
MultiMediaCard, 8-16
problems, 8-16
Overheating power down, 8-5
removing, 3-23
Password, 8-7
P PC Card, 8-13
Power, 8-4
Password
Real Time Clock, 8-7
power on, 3-7
Recovery Discs, 8-27
problems, 8-7
SD/SDHC Card, 8-14
Starting the computer by, 6-12
Self test, 8-4
Supervisor, 6-12
Smart Card, 8-14
user, 6-10
Sound system, 8-23
PC Card, 3-15
System start-up, 8-4
inserting, 3-16
TOSHIBA support, 8-28
problems, 8-13
Touch Pad, 8-16
removing, 3-16
USB device, 8-19
Power
USB floppy diskette drive, 8-13
button location, 2-9
USB mouse, 8-18
conditions, 6-1
Wireless LAN, 8-26
Hibernation Mode, 1-10
xD picture card, 8-15
indicators, 6-2
Processor, 3-1
panel on/off, 3-7, 6-13

User’s Manual Index-3

TECRA A10/S10/M10/SatellitePro S300

R TOSHIBA Express Port Replicator, 3-36

TOSHIBA HDD Protection, 3-8
Recovery Discs, 1-14
TOSHIBA PC Diagnostic Tool, 3-10
problems, 8-27
TOSHIBA Presentation button, 3-6
Recovery hard disk drive, 1-13, 1-14
TOSHIBA SD Memory Boot Utility, 3-12
Restarting the computer, 1-12
TOSHIBA SD Memory Card Format, 3-12
S TOSHIBA Theft Registration, I-2
TOSHIBA Value Added Package, 3-9
SD/SDHC Card
TOSHIBA Zooming Utility, 3-9
formatting, 3-21
inserting, 3-22 U
note, 3-20
USB device
problems, 8-14
problems, 8-19
removing, 3-23
USB FDD Kit, 3-29
Security lock, 3-35
USB floppy diskette drive
location, 2-4
problems, 8-13
Serial port, 3-33
Sleep Mode V
setting, 1-8 Video mode, B-1
System automatic, 3-7 Video RAM, 3-2
Smart Card, 3-17 Volume control dial, 2-2
inserting, 3-18 problems, 8-23
problems, 8-14
removing, 3-19 W
Soft keys Web Camera, 2-10, 3-5, 4-11
enhanced keyboard, 5-2 Windows Mobility Center, 3-13
ENTER, 5-3 Wireless communication, 4-34
ScrLock, 5-3 indicator, 2-13, 4-37
Sound system Wireless communication switch, 2-3, 4-37
headphone jack, 2-2 Wireless LAN, 3-6, 4-35
microphone, 2-2 problems, 8-26
microphone jack, 2-2
problems, 8-23 X
Stereo speakers, 2-11 xD picture card, 3-20
volume control dial, 2-2 inserting, 3-22
problems, 8-15
T removing, 3-23
TOSHIBA Assist, 3-12
TOSHIBA Assist button, 3-6
TOSHIBA ConfigFree, 3-12
TOSHIBA Disc Creator, 3-13, 4-26

Index-4 User’s Manual