Scribd
Upload
434 views

Jetfuel Typea1 Specifications

This document outlines the specifications for jet fuel Type JET A1 according to Platts NWE: PJAAV00 standards. It lists the acceptable minimum and maximum ranges for various composition, volatility, fluidity, combustion, corrosion, thermal stability, and contaminant properties. Additives such as antioxidants, static dissipators, and lubricity improvers are optionally allowed within specified limits.

Uploaded by

Fariz Azwar Azmi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
434 views

Jetfuel Typea1 Specifications

This document outlines the specifications for jet fuel Type JET A1 according to Platts NWE: PJAAV00 standards. It lists the acceptable minimum and maximum ranges for various composition, volatility, fluidity, combustion, corrosion, thermal stability, and contaminant properties. Additives such as antioxidants, static dissipators, and lubricity improvers are optionally allowed within specified limits.

Uploaded by

Fariz Azwar Azmi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Annex A

Specifications Type JET A1 - (Platts NWE: PJAAV00)


COMPONENT UNIT Min/Max Test Methods ASTM / IP / GOST

COMPOSITION
Appearance C&B (1) Visual
Colour, Saybolt Report (2) D156, D6045
Acidity, Total (mg KOH/g) Max. 0.10 D3242, IP 354
Aromatics (vol %) Max. 25.0 D1319, IP 156, GOST R 52063
Sulphur, Total (wt %) Max. 0.25, D1266, D1552, D2622, D4294, D5453, IP107, IP 243, IP
336, IP 373, IP 447,
GOST R 51947, GOST R 51859
Sulphur, Mercaptan (wt %) Max. 0.0030 (3) D3227, IP 342, GOST R 52030
OR Doctor Test Negative (3) D4952, IP 30
VOLATILITY
Distillation Temperature: D86, IP 123
10% Recovery (°C) Max. 205.0
50% Recovery (°C) Report
90% Recovery (°C) Report
Final BP (°C) Max. 300.0
Distillation Residue (vol %) Max. 1.5
Distillation Loss (vol %) Max. 1.5
Flash Point (°C) Min. 38.0 D56 (4), D3828, IP170
Density @ 15°C (kg/m3) 775.0 - 840.0 D1298, D4052, IP 160, IP 365, GOST R 51069
FLUIDITY
Freezing Point (°C) Max. -47.0 (5) D2386, D5972, D 7153, IP 16, IP 435, IP 529
Viscosity @ -20°C (cSt) Max. 8 D445, IP 71
COMBUSTION
Net Heat of Combustion (MJ/kg) Min. 42.80 (6) D3338, D4529, D4809, IP 12, IP 355
Smoke Point (mm) Min. 25 D1322, IP 57
OR Smoke Point (mm) Min. 19 D1322, IP57
AND Naphthalenes (vol %) Max. 3 D1840
CORROSION
Copper Strip (2h @ 100°C) Max. No.1 D130, IP 154
THERMAL STABILITY
JFTOT 6P @ 260ºC (mm Hg) Tube Rating Max. 25 D3241, IP 123
(Visual) Max. <3 (7)
CONTAMINANTS
Existent Gum Max. 7 (8) D381, IP 131
Water Reaction Interface Rating Max. 1b D1094
MSEP Rating Fuel without SDA Min. 85
Fuel with SDA Min. 70
Particulates (mg/dm3) Max. 1.0 (2) D5452, IP423
OTHER
Conductivity (pS/m) 50-600 D2624, IP 274, GOST 25950
Without SDA Max. 10
BOCLE Wear Scar Diameter (mm) Max. 0.85 (9) D5001
ADDITIVES
Antioxidant Optional (24 mg/L max)
Static Dissipator Optional (10)
Lubricity Improver Optional (11)

(1) Fuel should be clear, bright and visually free from solid matter & undissolved water at ambient air temperature.
(2) Applies at point of manufacture.
(3) In the event of a conflict between Sulphur Mercaptan and Doctor Test results, Sulphur Mercaptan shall prevail.
(4) When testing by method D 56, a minimum Flash Point of 40ºC applies.
(5) Lower freezing point may be agreed between customer & producer.
(6) When determining the Net Heat of Combustion by ASTM D4529, use equation 1 or Table 1, and when using D3338, use equation 2.
(7) No peacock or abnormal colour deposits allowed.
(8) Air can be used instead of steam as the vaporising agent.
(9) Applies at point of manufacture if fuel contains >95 % hydroprocessed material of which >20% has been severely hydroprocessed.
(10) Maximum initial doping is 3 mg/L. Upon redoping the fuel, the maximum allowed cumulative concentration is 5 mg/L.
(11) Hitec 580 may be injected at 15 - 23 mg/L.

You might also like