Telecommunication Systems Division

Digital Business Telephone Systems

Standard Telephone
User Guide

December 2002
Publication Information © Copyright 2002
Toshiba America Information Systems, Inc.
Toshiba America Information Systems, Inc., Telecommunication Systems Division
Telecommunication Systems Division, reserves the right,
without prior notice, to revise this information publication for All rights reserved. No part of this manual, covered by the
any reason, including, but not limited to, utilization of new copyrights hereon, may be reproduced in any form or by any
advances in the state of technical arts or to simply change the means—graphic, electronic, or mechanical, including
design of this document. recording, taping, photocopying, or information retrieval
systems—without express written permission of the publisher
Further, Toshiba America Information Systems, Inc., of this material.
Telecommunication Systems Division, also reserves the right,
without prior notice, to make such changes in equipment Strata is a registered trademark of Toshiba Corporation.
design or components as engineering or manufacturing Stratagy is a registered trademark of Toshiba America
methods may warrant. Information Systems, Inc.
CTX-UG-STDTELVA Trademarks, registered trademarks, and service marks are the
4016196 property of their respective owners.
Version A.3, December 2002
 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TAIS”)
Telecommunication Systems Division License Agreement
IMPORTANT: THIS LICENSE AGREEMENT (“AGREEMENT”) IS A LEGAL AGREEMENT BETWEEN YOU (“YOU”) AND TAIS. CAREFULLY READ THIS LICENSE AGREEMENT. USE OF ANY
SOFTWARE OR ANY RELATED INFORMATION (COLLECTIVELY, “SOFTWARE”) INSTALLED ON OR SHIPPED WITH A TAIS TELECOMMUNICATION SYSTEM PRODUCT OR OTHERWISE MADE
AVAILABLE TO YOU BY TAIS IN WHATEVER FORM OR MEDIA, WILL CONSTITUTE YOUR ACCEPTANCE OF THESE TERMS, UNLESS SEPARATE TERMS ARE PROVIDED BY THE SOFTWARE
SUPPLIER. IF YOU DO NOT AGREE WITH THE TERMS OF THIS LICENSE AGREEMENT, DO NOT INSTALL, COPY OR USE THE SOFTWARE AND PROMPTLY RETURN IT TO THE LOCATION
FROM WHICH YOU OBTAINED IT IN ACCORDANCE WITH APPLICABLE RETURN POLICIES. EXCEPT AS OTHERWISE AUTHORIZED IN WRITING BY TAIS, THIS SOFTWARE IS LICENSED FOR
DISTRIBUTION ONLY TO END-USERS PURSUANT TO THIS LICENSE AGREEMENT.

1. License Grant. The Software is not sold; it is licensed upon payment of applicable charges. TAIS grants to you a personal, non-transferable and non-exclusive right to use the copy of the Software
provided under this License Agreement. You agree you will not copy the Software except as necessary to use it on one TAIS system at a time at one location. Modifying, translating, renting, copying,
distributing, transferring or assigning all or part of the Software, or any rights granted hereunder, to any other persons and removing any proprietary notices, labels or marks from the Software is strictly
prohibited; You agree violation of such restrictions will cause irreparable harm to TAIS and provide grounds for injunctive relief, without notice, against You or any other person in possession of the Software.
You and any other person whose possession of the software violates this License Agreement shall promptly surrender possession of the Software to TAIS, upon demand. Furthermore, you hereby agree not
to create derivative works based on the Software. TAIS reserves the right to terminate this license and to immediately repossess the software in the event that You or any other person violates this License
Agreement.

2. Intellectual Property. You acknowledge that no title to the intellectual property in the Software is transferred to you. You further acknowledge that title and full ownership rights to the Software will remain
the exclusive property of TAIS and/or its suppliers, and you will not acquire any rights to the Software, except the license expressly set forth above. You will not remove or change any proprietary notices
contained in or on the Software. The Software is protected under US patent, copyright, trade secret, and/or other proprietary laws, as well as international treaties. Any transfer, use, or copying of the
software in violation of the License Agreement constitutes copyright infringement. You are hereby on notice that any transfer, use, or copying of the Software in violation of this License Agreement constitutes
a willful infringement of copyright.

3. No Reverse Engineering. You agree that you will not attempt, and if you employ employees or engage contractors, you will use your best efforts to prevent your employees and contractors from
attempting to reverse compile, reverse engineer, modify, translate or disassemble the Software in whole or in part. Any failure to comply with the above or any other terms and conditions contained herein will
result in the automatic termination of this license and the reversion of the rights granted hereunder back to TAIS.

4. Limited Warranty. THE SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, TAIS AND ITS SUPPLIERS
DISCLAIM ALL WARRANTIES WITH REGARD TO THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF NON-INFRINGEMENT OF THIRD
PARTY RIGHTS, THE WARRANTY OF YEAR 2000 COMPLIANCE, AND THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE SOFTWARE IS WITH YOU. NEITHER TAIS NOR ITS SUPPLIERS WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET
YOUR REQUIREMENTS OR THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE. HOWEVER, TAIS WARRANTS THAT ANY MEDIA ON WHICH THE
SOFTWARE IS FURNISHED IS FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE FOR A PERIOD OF NINETY (90) DAYS FROM THE DATE OF DELIVERY TO YOU.

5. Limitation Of Liability. TAIS’ ENTIRE LIABILITY AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LICENSE AGREEMENT SHALL BE AT TAIS’ OPTION REPLACEMENT OF THE MEDIA OR
REFUND OF THE PRICE PAID. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL TAIS OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL,
SPECIAL, INCIDENTAL OR INDIRECT DAMAGES FOR PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION/DATA, OR ANY
OTHER PECUNIARY LOSS OF ANY KIND ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE, EVEN IF TAIS OR ITS SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT SHALL TAIS OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM BY A THIRD PARTY.

6. State/Jurisdiction Laws. SOME STATES/JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, OR
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO SUCH LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE/JURISDICTION TO STATE/JURISDICTION.

7. Export Laws. This License Agreement involves products and/or technical data that may be controlled under the United States Export Administration Regulations and may be subject to the approval of the
United States Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the United States Export Administration Regulations, or any other applicable law, regulation or
order, is prohibited.

8. Governing Law. This License Agreement will be governed by the laws of the State of California, United States of America, excluding its conflict of law provisions.

9. United States Government Restricted Rights. The Software is provided with Restricted Rights. Use, duplication, or disclosure by the United States Government, its agencies and/or instrumentalities is
subject to restrictions as set forth in subparagraph (c)(1)(ii) of The Rights in Technical Data and Computer Software Clause at DFARS 252.227-7013 (October 1988) or subparagraphs (c)(1) and (2) of the
Commercial Computer Software - Restricted Rights at 48 CFR 52.227-19, as applicable.

10. Severability. If any provision of this License Agreement shall be held to be invalid, illegal or unenforceable, the validity, legality and enforceability of the remaining provisions hereof shall not in any way be
affected or impaired.

11. No Waiver. No waiver of any breach of any provision of this License Agreement shall constitute a waiver of any prior, concurrent or subsequent breach of the same or any other provisions hereof, and no
waiver shall be effective unless made in writing and signed by an authorized representative of the waiving party.

YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AGREEMENT AND THAT YOU UNDERSTAND ITS PROVISIONS. YOU AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU
FURTHER AGREE THAT THIS LICENSE AGREEMENT CONTAINS THE COMPLETE AND EXCLUSIVE AGREEMENT BETWEEN YOU AND TAIS AND SUPERSEDES ANY PROPOSAL OR PRIOR
AGREEMENT, ORAL OR WRITTEN, OR ANY OTHER COMMUNICATION RELATING TO THE SUBJECT MATTER OF THIS LICENSE AGREEMENT.

Toshiba America Information Systems, Inc.

Telecommunication Systems Division
9740 Irvine Boulevard
Irvine, California 92618-1697
United States of America

TSD 081601
5932
 Toshiba America Information Systems, Inc.
Telecommunication Systems Division

Limited Warranty
Toshiba America Information Systems, Inc., (“TAIS”) warrants that this voice processing equipment (except for fuses, lamps, and
other consumables) will, upon delivery by TAIS or an authorized TAIS dealer to a retail customer in new condition, be free from
defects in material and workmanship for twenty-four (24) months after delivery. This warranty is void (a) if the equipment is used
under other than normal use and maintenance conditions, (b) if the equipment is modified or altered, unless the modification or
alteration is expressly authorized by TAIS, (c) if the equipment is subject to abuse, neglect, lightning, electrical fault, or accident,
(d) if the equipment is repaired by someone other than TAIS or an authorized TAIS dealer, (e) if the equipment’s serial number is
defaced or missing, or (f) if the equipment is installed or used in combination or in assembly with products not supplied by TAIS
and which are not compatible or are of inferior quality, design, or performance.

The sole obligation of TAIS or Toshiba Corporation under this warranty, or under any other legal obligation with respect to the
equipment, is the repair or replacement by TAIS or its authorized dealer of such defective or missing parts as are causing the
malfunction with new or refurbished parts (at their option). If TAIS or one of its authorized dealers does not replace or repair such
parts, the retail customer’s sole remedy will be a refund of the price charged by TAIS to its dealers for such parts as are proven to
be defective, and which are returned to TAIS through one of its authorized dealers within the warranty period and no later than
thirty (30) days after such malfunction, whichever first occurs.

Under no circumstances will the retail customer or any user or dealer or other person be entitled to any direct, special, indirect,
consequential, or exemplary damages, for breach of contract, tort, or otherwise. Under no circumstances will any such person be
entitled to any sum greater than the purchase price paid for the item of equipment that is malfunctioning.

To obtain service under this warranty, the retail customer must bring the malfunction of the machine to the attention of one of
TAIS’ authorized dealers within the twenty-four (24) month period and no later than thirty (30) days after such malfunction,
whichever first occurs. Failure to bring the malfunction to the attention of an authorized TAIS dealer within the prescribed time
results in the customer being not entitled to warranty service.

THERE ARE NO OTHER WARRANTIES FROM EITHER TOSHIBA AMERICA INFORMATION SYSTEMS, INC., OR
TOSHIBA CORPORATION WHICH EXTEND BEYOND THE FACE OF THIS WARRANTY. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, AND FITNESS FOR USE, ARE EXCLUDED.

No TAIS dealer and no person other than an officer of TAIS may extend or modify this warranty. No such modification or
extension is effective unless it is in writing and signed by the vice president and general manager, Telecommunication Systems
Division.
Contents

Introduction
Organization....................................................................................................................... iii
Conventions ........................................................................................................................iv
Related Documents/Media..................................................................................................iv
Chapter 1 — The Basics
Ringing Patterns...................................................................................................................1
Flash .....................................................................................................................................2
Flashing Outside Lines .....................................................................................................2
Making a Call.......................................................................................................................2
Answering a Call..................................................................................................................2
Message Waiting..................................................................................................................3
Responding to a Message Waiting Indication ..................................................................3
Turning On/Off Message Waiting LED on Another Extension .......................................3
Call Transfer ........................................................................................................................4
Conference Calls ..................................................................................................................5
Adding Voice Mail to a Conference.................................................................................6
Connecting Two Outside Lines ........................................................................................6
Chapter 2 — Advanced Operation
Account Code Calls .............................................................................................................7
Verified/Non-Verified Account Codes.............................................................................7
Forced Account Codes......................................................................................................8
Voluntary Account Codes (Verified/Non-Verified).........................................................8
Automatic Busy Redial ........................................................................................................9
Automatic Callback .............................................................................................................9
Call Forward ......................................................................................................................10
System.............................................................................................................................10

Strata CTX Standard Telephone 12/02 i

 Contents
Chapter 2 – Advanced Operation

Station .............................................................................................................................10
Call Forward Categories .................................................................................................11
Call Forward Settings .....................................................................................................11
Call Forward Procedures ................................................................................................12
Call Park Orbits..................................................................................................................14
Call Pickup.........................................................................................................................15
Group Pickup ..................................................................................................................15
Page/Internal Call Pickup ...............................................................................................15
Call Waiting .......................................................................................................................16
Direct Inward System Access ............................................................................................17
Do Not Disturb...................................................................................................................17
Setting DND for Another Extension...............................................................................18
Door Lock(s) ......................................................................................................................18
Door Phone(s) ....................................................................................................................19
Emergency Ringdown........................................................................................................20
Override Calls ....................................................................................................................20
Busy Override.................................................................................................................20
Do Not Disturb Override ................................................................................................21
Executive Override .........................................................................................................21
Class of Service Override ...............................................................................................22
Privacy Override.............................................................................................................22
Paging ................................................................................................................................22
Answering a Page ...........................................................................................................23
All Call Page...................................................................................................................23
Emergency Page .............................................................................................................23
Privacy ...............................................................................................................................24
Redial .................................................................................................................................24
Speed Dial..........................................................................................................................24
Make a Call Using Speed Dial........................................................................................25
Store a Station Speed Dial Number ................................................................................25
Advanced Speed Dial Operation ....................................................................................25
Voice Mail - Direct Transfer..............................................................................................27
Other Voice Mail Features..............................................................................................27
Feature Access Codes ........................................................................................................28
Index ......................................................................................................................................33

ii PRELIMINARY & CONFIDENTIAL Strata CTX Standard Telephone 12/02

Introduction

This guide provides operating instructions for standard analog telephones connected
to a Strata CTX system.

Organization
This guide is divided as follows:
• Chapter 1 – The Basics provides descriptions and operating procedures for all of
the features available with standard analog telephones.
• Chapter 2 – Advanced Operation explains how to use the features which are
available on the standard telephone.

Strata CTX Standard Telephone 12/02 iii

 Introduction
Conventions

Conventions
Conventions Description
Elaborates specific items or references other information. Within some
Note tables, general notes apply to the entire table and numbered notes apply
to specific items.
Important! Calls attention to important instructions or information.
Arial Bold Represents telephone buttons.
shows a multiple PC keyboard or phone button entry. Entries without
spaces between them show a simultaneous entry.
+ Example: Delete+Enter.
Entries with spaces between them show a sequential entry.
Example: # + 5.
Tilde (~) Means “through.” Example: 350~640 Hz frequency range.
Grey words within the printed text denote cross-references. In the
electronic version of this document (Strata CTX WinAdmin Application
See Figure 10
Software and Documentation Library CD-ROM or FYI Internet
download), cross-references appear in blue hypertext.

Related Documents/Media
Note Some documents listed here may appear in different versions on the
CD-ROM or in print. To find the most current version, check the version/date in
the Publication Information on the back of the document’s title page.
Refer to the following for more information:
• Strata CTX WinAdmin Application Software and Documentation Library
CD-ROM

iv Strata CTX Standard Telephone 12/02

The Basics 1

This chapter shows you the basic operation of your standard analog telephone.
Notes
• A representative in your company is assigned as the CTX System Administrator
for the Strata CTX telephone system. The CTX System Administrator is
responsible for assigning telephone features. Be sure to check with your CTX
System Administrator and make sure you know which features are enabled on your
system.
• The feature access codes, such as #408 on page 3, can change if they are
reprogrammed. Again, check with your CTX System Administrator regarding
codes.

Ringing Patterns
• Trunk-to-station call – One second On, three seconds Off.
• Station-to-station call – 0.4 seconds On, 0.2 seconds Off, 0.4 seconds On, three
seconds Off.
Note Under special circumstances, Trunk-to-station calls may be programmed to
emulate outside facilities. Consult your CTX System Administrator.

Strata CTX Standard Telephone 12/02 1

 The Basics
Flash

Flash
The term “flash” is used in a number of feature instructions. Since many standard
telephones have a Flash button, this guide assumes that you have one. If your
standard telephone does not have a Flash button, perform the following to “Flash the
hookswitch.”
➤ To manually flash the hookswitch, while on a call, press the hookswitch down
about 1/2 second, then release it.
You should hear dial tone after doing this.

Flashing Outside Lines

Some outside line features, such as conferencing, Centrex, or behind PBX operation
require “flashing the outside line,” to dial Centrex/PBX feature access code or
extension numbers.

➤ To flash an outside line

1. Momentarily press the hookswitch for about 1/2 second. After you press the
hookswitch, you hear dial tone. This hookflashes the Toshiba system only.
2. Press #45. You hear Centrex or PBX dial tone. You can now dial a Centrex or
PBX feature access code or extension number.

Making a Call
➤ Lift the handset, then dial the number.
A line may be automatically selected or you can manually choose a line. Dial tone
plays through the handset. Call progress tones (Ringback Tone, Busy Tone, etc.)
are heard through the handset.

Answering a Call
➤ Pick up the handset.

2 Strata CTX Standard Telephone 12/02

 The Basics
Message Waiting

Message Waiting
A message light and/or interrupted dial tone indicates a message for your phone.
An extension can receive up to four simultaneous Message Waiting indications. One
message is reserved for the Message Center.

Responding to a Message Waiting Indication

1. Lift the handset, then press #408. Your phone rings the extension or voice mail
device that sent the indication.
2. After answering the message(s), place the handset back on-hook.
3. If the Msg indication remains On, you have more messages; repeat Steps 1~3
above to retrieve them. Voice mail devices turn Off the indications after a short
delay, after you checked all messages.
4. To manually turn off your Msg light, lift the handset, then press #409. Do this step
for each message received.

Turning On/Off Message Waiting LED on Another

Extension
If you call an extension and it is busy or there is no answer, you can light that
extension’s Message Waiting LED and enable that extension to call you back.
1. Dial an internal extension. You hear busy tone or there’s no answer.
2. Press 7. The Msg LED flashes red on the called phone.
3. Hang up. The Msg LED on the called telephone flashes until the called party
presses the flashing Msg button - which calls you back.
4. To turn Off a Message LED that you have turned on for another extension, press
#64 plus the extension number that has the message light set. Hang up to release
your telephone.

Strata CTX Standard Telephone 12/02 3

 The Basics
Call Transfer

Call Transfer
1. While on a call, press Flash. You hear internal dial tone.
2. Dial the extension where the call will be transferred. You can remain on the line
and announce the call or immediately “blind transfer” the call.
During call transfer, you can connect all three parties by pressing Flash.
• If you get voice mail, you can leave a message or hang up and let the
transferred caller leave a message.
• If you hear a long single tone, then announce the call over the called phone’s
speaker.
3. Transfer with Camp On: If the station to which you want to transfer the call is
busy, you may hang up and the transferred trunk or station will be camped on to the
busy destination.

➤ To transfer a call directly to Voice Mail (VM)

1. While on a call, press Flash.
2. Enter #407.
3. Enter the VM mailbox number (usually the same as the extension number), press
#. The call transfers immediately and your extension becomes idle.

4 Strata CTX Standard Telephone 12/02

 The Basics
Conference Calls

Conference Calls
You can conference together up to eight parties (including your own) - with up to six
parties being external network lines. The actual number of conference parties with
acceptable volume levels depends on the local and far end telephone line conditions.
The person who initiates the conference call is the Master. If, after the conference is
established, the Master exits the conference, and the first station to have been added to
the conference becomes the Master.

➤ To conference calls
1. While on a call, press Flash. You hear dial tone.
2. Call another station or outside line.
3. When the called party answers, press Flash. If you receive a busy tone or no
answer, press Flash again to return to the original connection.
4. All parties are conferenced.
5. Repeat the above steps to add lines to the conference. Keep in mind the maximum
number of allowed conference parties.
Note When the “master” of the conference hangs up, control is automatically
transferred to the first internal station added to the conference call. If no other
internal stations are included in the conference call, the call will be
disconnected.

➤ To transfer conference control

1. Do Steps 1 and 2 above to add the line you wish to transfer conference control to.
See previous Note.
2. Announce the call and hang up to transfer the call. This station now becomes the
conference “master” with the ability to add or delete parties.

Strata CTX Standard Telephone 12/02 5

 The Basics
Conference Calls

Adding Voice Mail to a Conference

The Conference Master can add voice mail to a conference. This feature enables
participants in a conference to listen to or leave a voice mail message during one
phone call.

➤ To add Voice Mail to a conference call (performed by Conference Master)

1. Press Flash to place the current call on Consultation Hold.
2. Dial the voice mail (VM) extension number, then enter the VM mailbox and
security code. This adds the voice mailbox to the conference.
3. Press Flash to reconnect to the original party. (You can continue to add
conference members by pressing Flash and dialing another extension.)
Now, all parties in the conference can listen to or record a message to this voice
mailbox. Only the Master can control the VM with touchtones.

Connecting Two Outside Lines

1. While talking on an outside call, press Flash. You hear dial tone.
2. Dial an outside line access code and outside phone number.
3. After the party answers, press Flash.
If you receive a busy tone or if the station does not answer, press Flash to return
to the original connection.
4. Hang-up. The two outside lines remain connected.
Note See the Call Pickup section to pick up a call on hold from another extension.

6 Strata CTX Standard Telephone 12/02

Advanced Operation 2

This chapter gives you instructions on using your telephone’s advanced functions.

Account Code Calls

Account Codes (Forced or Voluntary) can be used for a variety of reasons including
billing, tracking, and line restriction applications. Account Codes are assigned in the
system as a fixed length (default is six digits) and are recorded by the system, along
with the details of the calls, which can be printed on a Station Message Detail
Recording (SMDR) report.

Verified/Non-Verified Account Codes

If programmed for Verified Account Codes, the system checks the account code you
entered against a list created by the CTX System Administrator. The code you enter
must be on the list for the call to proceed. Non-verified account codes must be of a
uniform length specified by the CTX System Administrator.

Strata CTX Standard Telephone 12/02 7

 Advanced Operation
Account Code Calls

Forced Account Codes

Some applications require you to enter an Account Code. These Forced Account
Codes may be verified or non-verified, depending upon the application, but in either
case, the caller must enter a code before proceeding.

➤ To dial using Forced Account Codes

1. Place a call in the normal method.
If the call requires an Account Code, a burst of tone (Success Tone) is heard after
dialing the telephone number alerting you to enter the Account Code.
2. Enter the account number.
When the number of digits designated for account codes is entered, the number is
then checked against the verified list, if chosen, and the call will continue as
normal. If the number of digits entered for the account code is not reached or the
verified code does not match, then re-order tone is heard and the call is rejected.
You can bypass Forced Account Code requirements with three emergency numbers,
including 911. See your CTX System Administrator for these numbers:

1) 911 2) _______ 3) _______

Voluntary Account Codes (Verified/Non-Verified)

Voluntary Account Codes are optional. They can be entered during a call and are used
for tracking selected calls using SMDR call detail recording option.
If the system is set for Verified Account Codes, station users must enter a specific
code when entering the Voluntary Account Code(s) or the code is not validated for the
SMDR call report. This does not affect the call.

➤ To enter a Voluntary Account Code

Note It’s a good idea to warn the other party that you will be disconnected
momentarily when you enter the access code. Once the code is entered, you are
reconnected.
1. After accessing an outside line, press Flash. Your call is interrupted; you and the
other party cannot hear each other. You hear feature dial tone.
2. Dial #46 + the account code. After the account code is entered, the connection is
restored.

8 Strata CTX Standard Telephone 12/02

 Advanced Operation
Automatic Busy Redial

Automatic Busy Redial

After reaching a busy outside number, you can activate Automatic Busy Redial so that
the system automatically redials the number at regular intervals. The system repeats
the redial until the destination is no longer busy. This feature may not be on some
phones on your system. Automatic Busy Redial is not attempted while your station is
busy, but continues to time-out.

➤ To activate Automatic Busy Redial

1. When you reach a busy number, press Flash + #441. You hear busy tone.
2. Hang up. The system redials, up to 5 to 20 times, every 30 to 180 seconds
(depending on system programming). Your telephone receives ring tone when
Automatic Busy Redial dials the number and it is available.
3. Lift the handset and wait for the party to answer. If you do not pick up the handset
within recall timeout (5 to 60 seconds) after a connection is made, you hear a
muted ring for another 30 seconds, then the call disconnects.

➤ To cancel Automatic Busy Redial

➤ Lift the handset and press #442.

Automatic Callback
When you reach a busy station, you can set Automatic Callback to have the system
monitor the busy extension and notify you when it becomes idle.
Automatic Callback can also place you in queue for an available outside line, if you
reach a line group in which all lines are busy. When a station or line becomes
available, the system rings your telephone. Then when you answer, it automatically
rings the intended destination. The amount of time the system will wait for an idle
destination is set in system programming.

➤ To set Automatic Callback

1. If you hear busy tone after dialing an outside line access code or a station number,
press 4. Busy tone stops, followed by success tone, then busy tone resumes.
2. Hang up. You can make other calls while waiting.

Strata CTX Standard Telephone 12/02 9

 Advanced Operation
Call Forward

3. When the called station or outside line becomes idle, your telephone rings.
4. Answer within about three rings (5 to 180 secs., set in programming) to prevent the
callback from being cancelled. After you answer, you hear success tone.
If you hear a busy tone after answering a callback, the called party is already on
another call or the line has already been seized or has received an incoming call.
Your request is not cancelled. You will be called again the next time a line becomes
idle.
If you were attempting to make an outside call, the telephone number is
automatically dialed, including the account code or override codes that were used.

➤ To cancel ACB
➤ Lift the handset and press #431.

Call Forward
System
System Call Forward (which is set in Programming) automatically directs calls to a
predefined location, such as Voice Mail. See your CTX System Administrator to
determine which type of Call Forward you have, as well as the Call Forward location.

Station
Station Call Forward assigns Call Forward destinations for each extension on your
phone. Each extension can be independently set for a different Call Forward feature.
You can set a flexible button to perform any Call Forward function - see “Call
Forward Procedure” on page 12 for more details.
Call Forward must be set prior to receiving the call.
The following calls to your station can be forwarded:
• Internal calls
• Auto Attendant calls
• Outside lines that ring only your station
• Transferred internal or incoming line calls

10 Strata CTX Standard Telephone 12/02

 Advanced Operation
Call Forward

Call Forward Categories

• Call Forward Any Call – Forwards any call, whether an internal call or incoming
line call.
• Call Forward - Incoming Line – Forward incoming line calls only.
• Call Forward Any Call - Set for Another Station – Enables you to forward all
calls for another telephone within your telephone system.
• Call Forward - Incoming Line Set for Another Station– Enables you to set
forwarding of incoming line calls for another telephone within your telephone
system.
• Call Forward System – Forwards the calls to the destination preset for the entire
telephone system, commonly voice mail.
• Call Forward - External Location – Forwards incoming line calls that ring
directly to your extension to a destination outside the system.
You can change your forwarding destination from outside the system using the DISA
feature. See your CTX System Administrator for DISA telephone numbers and
security code access.

Call Forward Settings

• Call Forward All Calls – Forwards all calls immediately.
• Call Forward Busy/Do Not Disturb – Forwards calls immediately when your
extension is busy or in Do Not Disturb (DND) mode.
In Tone-first systems with multiple lines, Call Forward Busy forwards calls only
when all line appearances are in use. In Voice-first systems, Call Forward Busy
forwards all calls any time your telephone is in use.
• Call Forward - No Answer – Forwards all calls to your station whenever you do
not answer the call within a designated time (set by you when you enable the
feature).
• Call Forward Busy/Do Not Disturb/No Answer – Forwards all calls to your
station whenever you are busy, in the DND mode, or after ringing and you do not
answer the call within a designated time (set by you when you enable the feature).
• Call Forward Cancel – Cancels the set Call Forward feature. Notice that each
category of Call Forward has a different code for canceling.

Strata CTX Standard Telephone 12/02 11

 Advanced Operation
Call Forward

Call Forward Procedures

The following table contains Call Forward Button sequences. You can do a Call
Forward function by one, entering the button sequence as described, or two,
programming a flexible button to perform the sequence. See “Call Forward
Procedure” on page 12 for instructions on programming a flexible button.
Some Call Forward features require a Pass Code entry. Use the following procedure to
change your Pass Code.

➤ To change your Pass Code

➤ Lift the handset, press #670 + ext. no. + old Pass Code (1~15 digits) + # + new
Pass Code (1~15 digits) + #.

➤ To use the Call Forward button sequence

➤ Follow the instructions in the following table, shown under “Button Sequence.”
Some features require additional input, such as:
• Destination – If the destination is an outside number, press # after entering the
destination. The CTX accepts destination numbers of up to 32 digits.
• Timer – This is a two digit entry representing how long (8 to 160 seconds) your
telephone should ring before forwarding the call. If you enter one digit, you
must press # after entering the single digit.
• Pass Code – A four-digit code established by system programming to prevent
unauthorized changes. The code applies to the station to be forwarded; not to
the station entering the code.
Note In the following table, (Tone) means that a confirmation tone will play at that
point in the sequence.
Table 1 Call Forward Procedure

Feature Button Sequence

Call Forward Any Call (Internal and Incoming Line)
All Calls Lift handset, press #6011 (Tone) + Destination No. + # (Tone)
Busy Lift handset, press #6021 (Tone) + Dest. No. + # (Tone)
No Answer Lift handset, press #6031 (Tone) + Dest. No. + # (Tone) + Timer + #
Busy No Answer Lift handset, press #6041 + Dest. No. + # + Timer + #
Cancel Lift handset, press #6051 (Tone)

12 Strata CTX Standard Telephone 12/02

 Advanced Operation
Call Forward

Table 1 Call Forward Procedure (continued)

Feature Button Sequence

Call Forward - Incoming Line Calls
All Calls Lift handset, press #6013 (Tone) + Dest. No. + # (Tone)
Busy Lift handset, press #6023 (Tone) + Dest. No. + # (Tone)
No Answer Lift handset, press #6033 + Dest. No. (Tone) + Timer + # (Tone) + #
Busy No Answer Lift handset, press #6043 + Dest. No. (Tone) + Timer + # (Tone) + #
Cancel Lift handset, press #6053 (Tone)
Call Forward - Any Call - Set for Another Station
Lift handset, press #6012 (Tone) + ext. no. + Pass Code (Tone) + # + Dest. No. + #
All Calls
(Tone)
Lift handset, press #6022 (Tone) + ext. no. + Pass Code (Tone) + # + Dest. No. + #
Busy
(Tone)
Lift handset, press #6032 (Tone) + ext. no. + Pass Code (Tone) + # + Dest. No.
No Answer
(Tone) + # + Timer + # (Tone)
Lift handset, press #6042 + ext. no. + Pass Code + # (Tone) + Dest. No. (Tone) + #
Busy No Answer
+ Timer + # (Tone)
Cancel Lift handset, press #6052 (Tone) + ext. no. + Pass Code + # (Tone)
Call Forward - Incoming Line Call - Set for Another Station
Lift handset, press #6014 (Tone) + ext. no. + Pass Code + # (Tone) + Dest. No.
All Calls
(Tone) + #
Lift handset, press #6024 (Tone) + ext. no. + Pass Code + # (Tone) + Dest. No.
Busy
(Tone) + #
Lift handset, press #6034 (Tone) + ext. no. + Pass Code + # (Tone) + Dest. No.
No Answer
(Tone) + # + Timer + #
Lift handset, press #6044 (Tone) + ext. no. + Pass Code + # (Tone) + Dest. No.
Busy No Answer
(Tone) + # + Timer + #
Cancel Lift handset, press #6054 (Tone) + ext. no. + Pass Code + # (Tone)
Lift handset, press #670 (Tone) + ext. no. (Tone) + old Pass Code + # (Tone) + new
Change Pass Code
Pass Code (Tone) + #
Call Forward - System
Activate #620 (Tone)
Cancel #621 (Tone)

Strata CTX Standard Telephone 12/02 13

 Advanced Operation
Call Park Orbits

Call Park Orbits

The Call Park feature enables you to hold a call temporarily in a location other than
your telephone. These areas are called orbits. You or another telephone user can
retrieve a parked call from its orbit by specifying the orbit number. You can specify
one of 20 General Park Orbits (7000~7019) or a valid extension number within the
system.
Once you have parked a call in an orbit, you can:
• Hang up and retrieve the parked call at a later time
• Originate another call
• Access a voice paging device to announce the parked call for pickup from another
station
If you park a call and it is not retrieved, it will recall to the parking station and one of
the following occurs:
• If your station is idle when the system Call Park recall timer expires, the parked
call automatically recalls to your station.
• If your station is busy, the parked call camps on.

➤ To park a call
1. While on a call, press Flash + #33.
2. Specify the Park Orbit by doing one of the following:
• Enter a valid extension.
• Press # and the system automatically selects your extension as the orbit.
If the analog hold feature is set in programming, the line LED will flash on
other telephones, which enables the call to be picked up from another
telephone.
3. Hang up. If the parked call is not retrieved within a specified time, the call rings
back to your phone.

➤ To retrieve a parked call

1. Lift the handset, press #32.

14 Strata CTX Standard Telephone 12/02

 Advanced Operation
Call Pickup

2. Enter the Orbit Number where the call is parked or # to enter the extension from
which you are calling.

Call Pickup
You can pick up a call that is ringing another station’s extension, a call placed on hold
at another station and other types of calls.

Group Pickup
Stations can be assigned in system programming to Pickup Groups. As many as 32
groups can be created to enable you to easily pick up incoming (new or transferred) or
internal calls that are ringing stations that are in your group or in other groups. This
feature does not pick up held calls. You may belong to more than one group. See your
CTX System Administrator for group assignments.

Page/Internal Call Pickup

This feature picks up Internal (station to station), Group Page, and All Call Page calls.
If these types of calls occur at the same time, the pickup priority is station-to-station
and then Page calls in the order of occurrence. In some systems, this feature can be
applied to pick up All Call Page exclusively.

➤ To perform Call Pickup

1. Lift the handset.
2. Enter a code from the following table.
Table 2 Call Pickup Feature Codes

For Incoming Calls Dialing Description

Group #5#34 Picks up a call ringing to a member of your group.

#5#5 + Primary Picks up a call ringing on any line appearance of the telephone
Direct Extension
Ext. No. specified by its Primary extension number.

Picks up a call ringing to the specified extension number only.

Directory Number #5#22 + Ext. No.
Other lines ringing on the same phone are unaffected.

Any External Call #5#9 Picks up any incoming outside line call.

Strata CTX Standard Telephone 12/02 15

 Advanced Operation
Call Waiting

Table 2 Call Pickup Feature Codes (continued)

For Calls On Hold: Dialing Description

Local Retrieve #5#71 Picks up a call held on the telephone from which it is dialed.

#5#72 + Primary Retrieves a call held on the telephone specified extension

Remote Retrieve
Ext. No. number.

Picks up a call held on the specified outside line regardless of

#5#73 + Outside
Outside Line Retrieve the telephone placing the call on hold. Must enter three digits
Line No. (1~128)
(e.g., 007).

Directed Extension Picks up a call held on the specified extension number,

#5#74 + Ext. No.
Retrieve regardless of the instrument(s) on which it appears.

Notes
• The Primary extension number is the directory number by which the phone set is
defined. Other, non-primary extension numbers may also appear on the phone. By
convention, the Primary extension number is assigned to the first button on a
multi-button telephone.
• If more than one call is on hold, the call on the telephone’s lowest button number is
picked up.
• Ringing calls are picked up over held calls as a priority.

Call Waiting
You can answer a call that is transferred to your station, even when your station is
busy. When another call is camped onto your station, you hear two Camp-on tone
beeps.
If a call is sent to your station when busy, and your station does not have an extension
button available to receive the call, two camp-on tone beeps are sent to your
telephone. You must disconnect or transfer the existing call to answer the waiting call.

➤ To answer a waiting call by disconnecting or transferring the current call

➤ Hang up or transfer the existing call; the camped-on call rings your station.

16 Strata CTX Standard Telephone 12/02

 Advanced Operation
Direct Inward System Access

Direct Inward System Access

Outside callers with touch tone phones can call in to lines programmed for Direct
Inward System Access (DISA) and dial an extension or outgoing line without going
through an attendant or operator. See your CTX System Administrator for more
details.
1. From outside the system, dial the public telephone number assigned to DISA. The
call is answered and you hear CTX dial tone. If you do not dial within 10 seconds,
the line disconnects.
2. When you hear dial tone, dial an extension or an outside line.
3. If you dial an outside destination, you may need to enter a security code provided
to you by the CTX System Administrator. When you hear the tone, enter the
security code. If accepted, the call proceeds.
4. If you receive busy tone and you want to dial another number while the station is
still ringing, press * and repeat Step 2.

Do Not Disturb
If your station is in Do Not Disturb (DND) mode, internal, external and transferred
calls do not ring your station and Off-hook Call Announce calls are denied. You can
continue to make calls while in the DND mode. When originating a call in DND
mode, you will hear a short burst of interrupted dial tone followed by continuous dial
tone. You can start dialing at any time during either tone.
If you put your Primary extension into DND mode, all calls to that telephone are
rejected. If your extension is set for Call Forward-Busy or Call Forward-Busy/No
Answer, the call is redirected to the forwarding destination immediately.
If you put an extension other than the Primary extension into DND, only calls to that
extension on your phone will be blocked. Appearances of that extension on other
telephones continue to ring.

➤ To activate DND
➤ Press #6091 (hear Success Tone). When making calls, dial tone is stuttered while
DND is active.

Strata CTX Standard Telephone 12/02 17

 Advanced Operation
Door Lock(s)

➤ To deactivate DND
➤ Press #6092 (hear Success Tone). DND mode is de-activated.

Setting DND for Another Extension

➤ To activate DND for another extension
➤ Enter #6191 (hear Entry Tone) + the Primary extension of the remote extension +
the pass code + # (hear Success Tone). This sets DND as if activated by the
Primary extension on the target telephone.

➤ To deactivate DND for another extension

➤ Enter #6192 (hear Entry Tone) + the Primary extension of the remote extension +
the pass code + # (hear Success Tone). This removes DND from the target
telephone.

➤ To change your DND Pass Code

➤ Enter #670 (hear Entry Tone) + ext. no. (hear Entry Tone) + old pass code + #
(hear Entry Tone) + new pass code + # (hear Success Tone).

Door Lock(s)
➤ To unlock a door
➤ Press #12 + the Door Lock Number (see table).
The door unlocks for 3~30 seconds (set in system programming).

Door Lock Door Lock

Location Location
No. No.
0 6
1 7
2 8
3 9
4 10
5

18 Strata CTX Standard Telephone 12/02

 Advanced Operation
Door Phone(s)

Door Phone(s)
Door phones can be used to call telephones selected in system programming. When a
door phone calls, you hear a distinctive ringing tone, one or five times (set in system
programming). You can also call a door phone and monitor the surrounding area.
The number of possible door phones varies by Strata CTX system, with up to 24 as the
maximum for larger systems. Check with your CTX WinAdmin programmer to find
out the names and locations of your system’s door phones and record them below.

Door Phone Door Phone

Name/Location Name/Location
No. No.

➤ To answer a door phone call

➤ Lift the handset while the door phone is still ringing. You are connected to the door
phone
...or to pick up door phone calls ringing someone else’s phone, press extension +
#5#5 + directory number.

➤ To call/monitor a door phone

➤ Press #15 + extension for the door location. A two-way talk-path exists between
your telephone and the called door phone. You can audibly monitor the area around
the door phone.

Strata CTX Standard Telephone 12/02 19

 Advanced Operation
Emergency Ringdown

➤ To call from a door phone

1. Press the door phone button and then release it. You hear a distinctive ringing
tone–one or five times (set in system programming).
2. When answered, speak at a normal voice level in the direction of the door phone.

Emergency Ringdown
If a station remains off-hook for a programmable period, it can be automatically
treated as an Emergency Call and directed to an emergency destination. The station
may have partially dialed a number or have dialed no digits at all. Each station is
programmed with its specific emergency ringdown destination.
A station number or a group pilot number can be specified as an emergency ringdown
destination. In a private network, the station or pilot number must be in the same
network node. Remote emergency destination and door phones are not permitted.

Override Calls
The available override features are:

Busy Override
Ring Over Busy Override enables you to send a muted ring tone to a busy station to
indicate a call is waiting. The Busy Override (BOV) muted ring can be programmed
for each station to be two muted rings only or continued muted rings until the call is
answered. This option applies to the station receiving the muted ring. The muted ring
can be sent to the telephone speaker or to the telephone handset/headset and speaker.

➤ To use Busy Override

➤ After reaching a busy station, press 2. A muted tone is heard at the busy station,
indicating that a call is waiting. The station number displays.

20 Strata CTX Standard Telephone 12/02

 Advanced Operation
Override Calls

Do Not Disturb Override

Do Not Disturb (DND) Override lets you send a call waiting tone or ringing to a
station in DND mode to indicate that a call is coming in. Your telephone may be
programmed to block DND Override from other telephones. Your station’s LCD
shows the station you have called is in the DND mode.
OCA is possible to DND stations from stations that are programmed for DND
Override.

➤ To use DND Override

➤ After reaching a station in DND mode, press 2. A tone signal is heard at the DND
station, indicating a call is coming in.

Executive Override
Executive Override enables you to enter an established conversation. Your telephone
can also be programmed to block Executive Override from other telephones.

➤ To perform Executive Override

➤ After reaching a busy station, press 3
You enter a conference with the busy station and the party to whom he was talking.
The called parties may hear an optional tone signal prior to your entering the
conversation. If you do not have Override privileges, you will camp on.

Strata CTX Standard Telephone 12/02 21

 Advanced Operation
Paging

Class of Service Override

By dialing a Class of Service Override code, a user can change a station’s set of
privileges to one associated with the override code. When the call is terminated and
another is attempted from the same station, the original Class of Service is applied.
This allows selected users to override restrictions that are placed on any telephone in
the system.

➤ To perform Class of Service Override

1. Access an outside line. You hear dial tone.
2. Press Flash + #471. Dial tone stops.
3. Enter the Class of Service Override Code (four digits). You hear dial tone. For
security reasons, the override codes are only available on a selected basis. See your
CTX System Administrator.
4. Dial a telephone number.

Privacy Override
This feature enables you to enter an established call on a line you share with another
telephone. Up to two station users can enter an existing CO line-to-station call (i.e., up
to three stations can be connected to a CO line). You can also use this feature if the
station that is already connected to the CO line is in the Privacy Release mode.
Station users with Privacy Release can allow stations with the shared button
appearance to enter their conversations, even if the station entering the conversation is
not programmed for Privacy Override. (see “Privacy” on page 24.)

Paging
Station users can make page announcements to telephones and external speakers.
Check with your CTX System Administrator to find out the zone numbers for various
paging groups.

➤ To make a Page Announcement to a phones or external speakers

1. Lift the handset, and enter a paging access code.
2. Make your announcement, then hang up.

22 Strata CTX Standard Telephone 12/02

 Advanced Operation
Paging

➤ To make a Group Page

➤ Lift the handset, press #31 and enter the group number (01~16).

Answering a Page
➤ To answer a Group Page, lift the handset, press #5#35 and enter the Group
number.
➤ To answer an External Group Page, lift the handset, press #5#36 and enter the
Group number.

All Call Page

You can make an All Call Page to telephones assigned to the “All Call Page Group.”
Stations are assigned to the “All Call Page Group” in system programming.

➤ To make an All Call Page

1. Lift the handset, press #30. This pages all phones in the All Call Page Group but,
depending on system programming, you may or may not page external speakers.
2. Make your announcement then hang up.

➤ To answer an All Call Page

➤ Lift the handset, press #5#35.

Emergency Page
An Emergency Page overrides Group Pages or All Call Pages to telephone and
external paging devices.
➤ To make an Emergency Page, lift the handset and press #37.
➤ To make an Emergency Page to a group, lift the handset, press #38 and enter the
Zone number.

Strata CTX Standard Telephone 12/02 23

 Advanced Operation
Privacy

Privacy
Privacy controls the ability of more than one person to use the same extension or
outside line at the same time. Privacy applies to multiple appearances of extensions,
Phantom extensions, outside Lines and outside Line Group buttons.The application of
Privacy to individual telephones is controlled in system programming.
By default, the system is private. If you are in a conversation, another telephone with
an appearance of the line on which you are talking cannot intrude unless that
telephone has been programmed for Privacy Override. In that event, the other
telephone may enter and leave the conversation at will. If all users are provided with
Privacy Release in Class of Service, the system will function as non-private.

Redial
Use this button to redial the last number dialed from your phone.
➤ To redial the last number, press *0.

Speed Dial
Speed Dial enables you to dial a sequence of up to 32 digits with a shorter code. Dial
sequences can include telephone numbers, authorization codes, passwords feature
activation codes and pauses. Speed Dial may be used to originate a call or invoked
after a call is established.
There are two types of Speed Dial.
• Station – Your CTX System Administrator allocates a block of up to 100 personal
speed dial numbers in increments of 10 per phone. You can create and change these
numbers from your own phone. You have exclusive use of them.
• System – All telephones in your system can share a list of up to 800 System Speed
Dial numbers under the exclusive control of the CTX System Administrator. In
some cases, System Speed Dial will allow you to reach numbers that you would
not be allowed to dial directly from your telephone.

24 Strata CTX Standard Telephone 12/02

 Advanced Operation
Speed Dial

Make a Call Using Speed Dial

1. To begin a Speed Dial Call, press *.
2. Then, dial the Station or System Speed Dial Number. Station Speed Dial numbers
occupy numbers 100~199. System Speed Dial numbers occupy numbers 200~999.

Store a Station Speed Dial Number

➤ To store a Station Speed Dial Number using an Access Code
1. Dial #66. You hear Entry Tone.
2. Dial the Station Speed Dial number (100~199). You hear Entry Tone.
Note Selected telephones may have the ability to change System Speed Dial
numbers. Follow this procedure, but specify a System Speed Dial number
(200~999) instead.
3. Enter the destination digits, then press #. You hear Success Tone.
4. Release the phone. To enter another number, repeat the process, starting with
Step 1.

CTX System Administration

The third method of storing station Speed Dial numbers is via your CTX System
Administrator, who can establish your Station Speed Dial number through
administrative software and associate a name with it.

Advanced Speed Dial Operation

Special Characters
Speed Dial Numbers may include 0~9, #, * and Pause. When using the Access Code
input method (see above) it is also necessary to use # to indicate you have finished
entering the destination number. This creates 14 functions to be input from the 12
buttons on the dial pad.

Strata CTX Standard Telephone 12/02 25

 Advanced Operation
Speed Dial

Long Speed Dial Numbers

Speed Dial Numbers are stored sequentially in memory areas capable of holding 32
digits. If you exceed 32 digits, the excess are stored in the next higher area and
consume the next sequential Speed Dial Number.
You can dial the entire string by entering the original Speed Dial Number and all digits
will be sent, including those in excess of 32. If that were Speed Dial Number 100,
Number 101 would no longer be available. You are not prevented from storing a new
Number 101 but, if you do, Number 100 will be shortened to 32 digits.
When * is used as an escape character, it consumes one Speed Dial digit. Entering *7
to insert a seven-second pause would consume two of 32 characters.
“*” functions as an escape key indicating that the number immediately following
represents something exceptional. The numbers are defined in Table 3.

Table 3 Dial String Characters

Entry Meaning
0~9 0~9
# End of Speed Dial Number when entering via access code (#66)

* Escape

Pause (1~9) seconds. If you need to pause longer than nine seconds, enter additional
pause escape sequences. For example, to insert a 17 second pause, enter *9*8. The
* (1~9) display of a pause in the Speed Dial Number shows a “P” without specifying the
duration. In this example, you would see “PP.”

** *
*# #

26 Strata CTX Standard Telephone 12/02

 Advanced Operation
Voice Mail - Direct Transfer

Voice Mail - Direct Transfer

The Strata CTX enables you to transfer a call directly to a voice mailbox without first
ringing that person’s telephone.

➤ To transfer a call directly to Voice Mail (VM)

1. While on a call, press Flash. You hear feature dial tone.
2. Enter #407. You hear entry tone.
3. Enter the VM mailbox number (usually the same as the extension number), press
#. The call transfers immediately and your extension becomes idle.

Other Voice Mail Features

Another voice mail feature lets you to include a voice mailbox in a conference call.
See “Adding Voice Mail to a Conference” on page 6. For instructions on the Stratagy
ES Voice Mail features, refer to the Stratagy ES Voice Processing User Guide.

Strata CTX Standard Telephone 12/02 27

 Advanced Operation
Feature Access Codes

Feature Access Codes

Enter the sequence shown in Table 4 for the particular feature that you want to use.
Table 4 Feature Access Codes

Feature Feature Access Code Sequences

Account Code Cnf/Trn + #46 + Account code digits
Attendant Console 0
Automatic Busy Redial - On #441
Automatic Busy Redial - Off #442
Automatic Callback Cancel #431
Background Music
Telephone Speaker On Lift handset, press #490 + source number + #
Telephone Speaker Off Lift handset, press #491
External Speaker On Lift handset, press #492 + source number + #
External Speaker Off Lift handset, press #493
Call Forward - Any Calls (Internal and External)
All Call Lift handset, press #6011 (Tone) + Dest. No + # (Tone)
Busy Lift handset, press #6021 (Tone) + Dest. No + # (Tone)
No Answer Lift handset, press #6031 (Tone) + Dest. No. + # (Tone) + Timer + #
Busy No Answer Lift handset, press #6041 + Dest. No. + # + Timer + #
Cancel Lift handset, press #6051 (Tone)
Call Forward - Incoming Line Calls
All Call Lift handset, press #6013 + Dest. No.
Busy Lift handset, press #6023 + Dest. No.
No Answer Lift handset, press #6033 + Dest. No. + Timer + #
Busy No Answer Lift handset, press #6043 + Dest. No. + Timer + #
Cancel Lift handset, press #6053

28 Strata CTX Standard Telephone 12/02

 Advanced Operation
Feature Access Codes

Table 4 Feature Access Codes (continued)

Feature Feature Access Code Sequences

Call Forward Any Call - Set for Another Station
All Call Lift handset, press #6012 + ext. no. + Pass Code + # + Dest. No. + #
Busy Lift handset, press #6022 + ext. no. + Pass Code + # + Dest. No. + #
Lift handset, press #6032 + ext. no. + Pass Code + # + Dest. No. + #
No Answer
+ Timer + #
Lift handset, press #6042 + ext. no. + Pass Code + # + Dest. No. + #
Busy No Answer
+ Timer + #
Cancel Lift handset, press #6052 + ext. no. + Pass Code + #
Call Forward - Incoming Line Call - Set for Another Station
All Calls Lift handset, press #6014 + ext. no. + Pass Code + # + Dest. No. + #
Busy Lift handset, press #6024 + ext. no. + Pass Code + # + Dest. No. + #
Lift handset, press #6034 + Dest. No. + # + ext. no. + Pass Code + #
No Answer
+ Dest. No. + # + Timer + #
Lift handset, press #6044 + Dest. No. + # + ext. no. + Pass Code + #
Busy No Answer
+ Dest. No. + # + Timer + #
Cancel Lift handset, press #6054 + ext. no. + Pass Code + #
Lift handset, press #670 + ext. no. + old Pass Code + # + new Pass
Change Pass Code
Code + #
Call Forward - System
Activate #620
Cancel #621
Call Park
Activate Cnf/Trn + #33 + Orbit Number
Retrieve Lift handset, press #32 + Orbit Number
System Orbits 7000~7019
Call Pickup
Incoming - Group Pickup Lift handset, press #5#34
Incoming - Directed Station
Lift handset, press #5#5 + Ext. Number to be picked up
Pickup
Incoming - Directed Extension
Lift handset, press #5#22 + Ext. Number
Pickup
On hold - Local Retrieve Lift handset, press #5#71
On hold - Remote Retrieve Lift handset, press #5#72 + Remote Ext. No.

Strata CTX Standard Telephone 12/02 29

 Advanced Operation
Feature Access Codes

Table 4 Feature Access Codes (continued)

Feature Feature Access Code Sequences

On hold - Outside line Retrieve Lift handset, press #5#73 + Line on hold
On hold - Directed Extension
Lift handset, press #5#74 + Ext. No. on hold
Retrieve
Incoming - Any External Call Lift handset, press #5#9
Conferencing - Three Way #494
#658 + old Security Code (1~15 digits) + # + new Security Code
DISA Security Code - Change
(1~15 digits) + #
Do Not Disturb
Local - On #6091
Local - Off #6092
Remote - On #6191 + ext. no. + Pass Code Number + #
Remote - Off #6192 + ext. no. + Pass Code Number + #
Door Lock Control #12 + Door Lock Number
Door Phone Calling #15 + Door Phone No.
Emergency Call #911
Flash - Short #450
Flash - Long #451
LCR (Outgoing Call) 9
Message Waiting (MW)
Release a received MW #409
Retrieve a received MW #408
Activate MW at another Station
#63 + Ext. no.
without Ringing
Cancel MW at another Station
#64 + Ext. no.
without Ringing
Private Network Access Code 8 + Private Network No.
Night Ring Answer #5#39
Override
Busy, Do Not Disturb 2
Executive 3

30 Strata CTX Standard Telephone 12/02

 Advanced Operation
Feature Access Codes

Table 4 Feature Access Codes (continued)

Feature Feature Access Code Sequences

Paging
Page All Groups #30
Page Individual Groups #31 + Group Number
Emergency Page - Individual
#38 + Group Number
Group
Emergency Page - All Groups #37
Answer Page - All Groups #5#35
Answer for External Group Page #5#36 + Zone Number
Repeat Last Number Dialed *0
Speed Dial Register #66
Station (00~99) *1 + Index Number (00~99)
*2 + Index Number (000~099)
*3 + Index Number (100~199)
*4 + Index Number (200~299)
System *5 + Index Number (300~399)
*6 + Index Number (400~499)
*7 + Index Number (500~599)
*8 + Index Number (600~699)
*9 + Index Number (700~799)
Start Application #18
Substitution of Dial “#” 441
Substitution of Dial “ ”
* 441
Travelling Class Override
Enter Code #471
Change Code #69 + Index Number + old Code + # + new Code + #
Voice Mail (VM)
Direct Transfer to Voice Mail #407 + VM Number + #

Strata CTX Standard Telephone 12/02 31

 Advanced Operation
Feature Access Codes

32 Strata CTX Standard Telephone 12/02

Index

A definitions, 11
about this book pass code, 12
conventions, iv station, 10
related documents, iv system, 10, 29
access codes, 28 call hold, 6
account code, 28 call park, 29
calls, 7 orbits, 14
forced account codes (verified/non- call pickup, 15, 29
verified), 7, 8 call transfer, 4
voluntary, 8 call waiting, 16
all call page, 23 change pass code, 12
analog hold, 14 CO line queuing, 17
answering a call, 2 conference
attendant console, 28 calls, 5
automatic hold, 7
busy redial, 28 voice mail, 6
callback, 9 conferencing, 30
callback cancel, 28
D
B direct inward system access (see DISA)
background music (BGM), 28 DISA, 17
busy override, 20 do not disturb, 17, 30
override, 21
C door lock, 18
control, 30
call forward
door phone, 19
access codes, 28
calling, 30
any call, 11

Strata CTX Standard Telephone 12/02 33

 Index
E~V

E P
emergency paging, 15, 22
call, 30 access codes, 31
page, 23 pass code, 12
emergency ringdown, 20 pick up group calls, 15
executive override, 21 privacy, 24
override, 22
F private network access, 30
feature access codes, 28
flash, 2, 30 R
flash an outside line, 2 repeat last number dialed, 31
forced account codes (verified/non- ringing patterns, 1
verified), 7, 8
S
G speed dial, 24
group pickup, 15 access codes, 31
start application, 31
H
hold, 6 T
analog, 14 transfer, 4
travelling class override, 31
M two (tandem) outside line connection, 6
message waiting, 30
message waiting light V
on another telephone, 3 voice mail
access codes, 31
N conference, 6
night ring answer, 30 direct transfer, 27
voluntary account codes (verified/non-
O verified), 8
override, 20
access codes, 30
busy, 20
do not disturb, 21
executive, 21
privacy, 22
travelling class, 31

34 Strata CTX Standard Telephone 12/02