Scribd
Upload
107 views

Staad Report

The document provides information about a structural analysis for a space frame structure with 60 nodes and 74 elements. It describes 5 basic load cases and 8 combination load cases that were analyzed. The document then lists the coordinates of the 60 nodes that define the structure's geometry.

Uploaded by

ashutosh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
107 views

Staad Report

The document provides information about a structural analysis for a space frame structure with 60 nodes and 74 elements. It describes 5 basic load cases and 8 combination load cases that were analyzed. The document then lists the coordinates of the 60 nodes that define the structure's geometry.

Uploaded by

ashutosh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 166

Job No Sheet No Rev

1
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Job Information
Engineer Checked Approved

Name:
Date: 24-Jun-19

Structure Type SPACE FRAME

Number of Nodes 60 Highest Node 60


Number of Elements 74 Highest Beam 74

Number of Basic Load Cases 5


Number of Combination Load Cases 8

Included in this printout are data for:


All The Whole Structure

Included in this printout are results for load cases:


Type L/C Name

Primary 1 DL
Primary 2 WL-U
Primary 3 WL- D
Primary 4 WL-X
Primary 5 WL-Z
Combination 6 DL+WL UP
Combination 7 DL+WLDW
Combination 8 DL+WL-X
Combination 9 DL+WL-Z
Combination 10 DL+WLUP+WL-Z
Combination 11 DL+WL DW+WL-Z
Combination 12 DL+WLUP+WL-X
Combination 13 DL+WL DW+WL-X

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 166
Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Y
X
Z Load 6

Whole Structure

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 166
Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

3D Rendered View

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 166
Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Nodes
Node X Y Z
(mm) (mm) (mm)
1 0.000 0.000 0.000
2 0.000 400.000 2.2E+3
3 0.000 555.000 1.62E+3
4 0.000 736.000 946.000
5 0.000 912.000 289.000
6 0.000 992.000 0.000
7 0.000 1.18E+3 -724.000
8 0.000 1.25E+3 -956.000
9 0.000 250.000 0.000
10 0.000 500.000 0.000
11 2.8E+3 0.000 0.000
12 2.8E+3 400.000 2.2E+3
13 2.8E+3 555.000 1.62E+3
14 2.8E+3 736.000 946.000
15 2.8E+3 912.000 289.000
16 2.8E+3 992.000 0.000
17 2.8E+3 1.18E+3 -724.000
18 2.8E+3 1.25E+3 -956.000
19 2.8E+3 250.000 0.000
20 2.8E+3 500.000 0.000
21 5.6E+3 0.000 0.000
22 5.6E+3 400.000 2.2E+3
23 5.6E+3 555.000 1.62E+3
24 5.6E+3 736.000 946.000
25 5.6E+3 912.000 289.000
26 5.6E+3 992.000 0.000
27 5.6E+3 1.18E+3 -724.000
28 5.6E+3 1.25E+3 -956.000
29 5.6E+3 250.000 0.000
30 5.6E+3 500.000 0.000
31 8.4E+3 0.000 0.000
32 8.4E+3 400.000 2.2E+3
33 8.4E+3 555.000 1.62E+3
34 8.4E+3 736.000 946.000
35 8.4E+3 912.000 289.000
36 8.4E+3 992.000 0.000
37 8.4E+3 1.18E+3 -724.000
38 8.4E+3 1.25E+3 -956.000
39 8.4E+3 250.000 0.000
40 8.4E+3 500.000 0.000
41 -875.000 400.000 2.2E+3
42 -875.000 736.000 946.000
43 -875.000 912.000 289.000
44 -875.000 1.25E+3 -956.000
45 9.27E+3 400.000 2.2E+3

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 166
Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Nodes Cont...
Node X Y Z
(mm) (mm) (mm)
46 9.27E+3 736.000 946.000
47 9.27E+3 912.000 289.000
48 9.27E+3 1.25E+3 -956.000
49 1.4E+3 1.25E+3 -956.000
50 1.4E+3 912.000 289.000
51 1.4E+3 400.000 2.2E+3
52 1.4E+3 736.000 946.000
53 4.2E+3 1.25E+3 -956.000
54 4.2E+3 912.000 289.000
55 4.2E+3 400.000 2.2E+3
56 4.2E+3 736.000 946.000
57 7E+3 1.25E+3 -956.000
58 7E+3 912.000 289.000
59 7E+3 400.000 2.2E+3
60 7E+3 736.000 946.000

Beams
Beam Node A Node B Length Property 
(mm) (degrees)
1 8 7 240.934 2 0
2 7 6 749.026 2 0
3 6 5 299.868 2 0
4 5 4 680.165 2 0
5 4 3 700.778 2 0
6 3 2 599.388 2 0
7 6 1 992.000 1 90
8 7 10 996.008 4 0
9 9 3 1.65E+3 4 0
10 18 17 240.934 2 0
11 17 16 749.026 2 0
12 16 15 299.868 2 0
13 15 14 680.165 2 0
14 14 13 700.778 2 0
15 13 12 599.388 2 0
16 16 11 992.000 1 90
17 17 20 996.008 4 0
18 19 13 1.65E+3 4 0
19 28 27 240.934 2 0
20 27 26 749.026 2 0
21 26 25 299.868 2 0
22 25 24 680.165 2 0
23 24 23 700.778 2 0
24 23 22 599.388 2 0

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 166
Job No Sheet No Rev
6
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Beams Cont...
Beam Node A Node B Length Property 
(mm) (degrees)
25 26 21 992.000 1 90
26 27 30 996.008 4 0
27 29 23 1.65E+3 4 0
28 38 37 240.934 2 0
29 37 36 749.026 2 0
30 36 35 299.868 2 0
31 35 34 680.165 2 0
32 34 33 700.778 2 0
33 33 32 599.388 2 0
34 36 31 992.000 1 90
35 37 40 996.008 4 0
36 39 33 1.65E+3 4 0
37 8 49 1.4E+3 3 0
38 5 50 1.4E+3 3 0
39 2 51 1.4E+3 3 0
40 4 52 1.4E+3 3 0
41 18 53 1.4E+3 3 0
42 15 54 1.4E+3 3 0
43 12 55 1.4E+3 3 0
44 14 56 1.4E+3 3 0
45 28 57 1.4E+3 3 0
46 25 58 1.4E+3 3 0
47 22 59 1.4E+3 3 0
48 24 60 1.4E+3 3 0
49 2 41 875.000 3 0
50 4 42 875.000 3 0
51 5 43 875.000 3 0
52 8 44 875.000 3 0
53 32 45 875.000 3 0
54 34 46 875.000 3 0
55 35 47 875.000 3 0
56 38 48 875.000 3 0
57 49 18 1.4E+3 3 0
58 50 15 1.4E+3 3 0
59 51 12 1.4E+3 3 0
60 52 14 1.4E+3 3 0
61 49 50 1.29E+3 5 0
62 52 51 1.3E+3 5 0
63 53 28 1.4E+3 3 0
64 54 25 1.4E+3 3 0
65 55 22 1.4E+3 3 0
66 56 24 1.4E+3 3 0
67 53 54 1.29E+3 5 0
68 56 55 1.3E+3 5 0
69 57 38 1.4E+3 3 0

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 6 of 166
Job No Sheet No Rev
7
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Beams Cont...
Beam Node A Node B Length Property 
(mm) (degrees)
70 58 35 1.4E+3 3 0
71 59 32 1.4E+3 3 0
72 60 34 1.4E+3 3 0
73 57 58 1.29E+3 5 0
74 60 59 1.3E+3 5 0

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 140CS60X3.15 8.712 41.703 259.593 0.000 STEEL
2 100CU40X2 3.451 5.220 51.460 0.000 STEEL
3 90CS40X2 3.703 8.271 45.813 0.000 STEEL
4 40LU20X2 0.000 0.000 0.000 0.000 STEEL
5 Cir 0.01 0.785 0.049 0.049 0.098 STEEL
6 60CU30X1.6 1.825 1.632 10.236 0.000 STEEL
7 100CU50X2 3.851 9.687 61.064 0.000 STEEL
8 200CU50X4 11.405 21.994 592.857 0.000 STEEL
9 180CU50X3.15 8.451 17.362 370.188 0.000 STEEL
10 90CU50X3.15 5.616 14.087 71.370 0.000 STEEL
11 100CU40X1.6 2.785 4.250 41.990 0.000 STEEL
12 150CS50X3.15 8.397 27.276 271.603 0.000 STEEL
13 30LU30X1.6 0.000 0.000 0.000 0.000 STEEL
14 40LU40X2 0.000 0.000 0.000 0.000 STEEL
15 70CU30X1.6 1.985 1.715 14.669 0.000 STEEL
16 100CU60X3.15 6.561 24.202 106.008 0.000 STEEL
17 90CU40X2 3.251 5.055 40.198 0.000 STEEL
18 100CU40X3.15 5.301 7.806 76.461 0.000 STEEL
19 50CS40X1.25 1.759 3.869 7.559 0.000 STEEL
20 50CS40X1.6 2.210 4.724 9.324 0.000 STEEL
21 50CS50X1.6 2.530 8.212 11.198 0.000 STEEL
22 50CS25X1.25 1.384 1.245 5.331 0.000 STEEL

Materials
Mat Name E  Density 
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 7 of 166
Job No Sheet No Rev
8
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Supports
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
1 Fixed Fixed Fixed Fixed Fixed Fixed
11 Fixed Fixed Fixed Fixed Fixed Fixed
21 Fixed Fixed Fixed Fixed Fixed Fixed
31 Fixed Fixed Fixed Fixed Fixed Fixed

Primary Load Cases


Number Name Type

1 DL Dead
2 WL-U Wind
3 WL- D Wind
4 WL-X Wind
5 WL-Z Wind

Combination Load Cases


Comb. Combination L/C Name Primary Primary L/C Name Factor

6 DL+WL UP 1 DL 1.00
2 WL-U 1.00
7 DL+WLDW 1 DL 1.00
3 WL- D 1.00
8 DL+WL-X 1 DL 1.00
4 WL-X 1.00
9 DL+WL-Z 1 DL 1.00
5 WL-Z 1.00
10 DL+WLUP+WL-Z 1 DL 1.00
2 WL-U 1.00
5 WL-Z 1.00
11 DL+WL DW+WL-Z 1 DL 1.00
3 WL- D 1.00
5 WL-Z 1.00
12 DL+WLUP+WL-X 1 DL 1.00
2 WL-U 1.00
4 WL-X 1.00
13 DL+WL DW+WL-X 1 DL 1.00
3 WL- D 1.00
4 WL-X 1.00

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 8 of 166
Job No Sheet No Rev
9
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements
Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
2:WL-U 0.000 0.000 0.000 0.000 0.000 0.000 0.000
3:WL- D 0.000 0.000 0.000 0.000 0.000 0.000 0.000
4:WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
5:WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
6:DL+WL UP 0.000 0.000 0.000 0.000 0.000 0.000 0.000
7:DL+WLDW 0.000 0.000 0.000 0.000 0.000 0.000 0.000
8:DL+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
9:DL+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
10:DL+WLUP+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
11:DL+WL DW+WL-Z0.000 0.000 0.000 0.000 0.000 0.000 0.000
12:DL+WLUP+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
13:DL+WL DW+WL-X0.000 0.000 0.000 0.000 0.000 0.000 0.000
2 1:DL -0.212 -19.307 -4.338 19.789 0.012 0.000 -0.002
2:WL-U 1.602 140.882 31.724 144.419 -0.086 -0.003 0.016
3:WL- D -1.021 -89.766 -20.214 92.019 0.055 0.002 -0.010
4:WL-X 15.063 -1.598 -0.207 15.149 0.001 0.001 0.001
5:WL-Z -0.000 1.277 0.412 1.341 -0.001 -0.000 -0.000
6:DL+WL UP 1.391 121.575 27.386 124.629 -0.074 -0.003 0.014
7:DL+WLDW -1.233 -109.072 -24.552 111.808 0.066 0.002 -0.012
8:DL+WL-X 14.851 -20.905 -4.545 26.043 0.013 0.002 -0.001
9:DL+WL-Z -0.212 -18.030 -3.926 18.454 0.011 0.000 -0.002
10:DL+WLUP+WL-Z 1.391 122.852 27.798 125.965 -0.075 -0.003 0.014
11:DL+WL DW+WL-Z-1.233 -107.796 -24.140 110.473 0.066 0.002 -0.012
12:DL+WLUP+WL-X16.453 119.977 27.179 124.112 -0.073 -0.002 0.015
13:DL+WL DW+WL-X
13.830 -110.671 -24.758 114.246 0.067 0.004 -0.011
3 1:DL -0.163 -12.623 -2.549 12.879 0.011 0.000 -0.002
2:WL-U 1.119 91.861 18.607 93.734 -0.082 -0.002 0.012
3:WL- D -0.713 -58.531 -11.856 59.724 0.052 0.002 -0.007
4:WL-X 13.562 -1.098 -0.073 13.607 0.001 -0.119 0.458
5:WL-Z 0.000 0.791 0.282 0.840 -0.001 0.000 0.000
6:DL+WL UP 0.955 79.239 16.058 80.855 -0.070 -0.002 0.010
7:DL+WLDW -0.876 -71.154 -14.405 72.603 0.063 0.002 -0.009
8:DL+WL-X 13.399 -13.721 -2.623 19.356 0.012 -0.119 0.457
9:DL+WL-Z -0.163 -11.831 -2.268 12.048 0.010 0.000 -0.002
10:DL+WLUP+WL-Z 0.956 80.030 16.339 81.687 -0.071 -0.002 0.010
11:DL+WL DW+WL-Z-0.876 -70.362 -14.123 71.771 0.062 0.002 -0.009
12:DL+WLUP+WL-X14.517 78.141 15.984 81.069 -0.070 -0.121 0.468
13:DL+WL DW+WL-X
12.686 -72.252 -14.478 74.772 0.064 -0.117 0.449
4 1:DL -0.089 -5.676 -0.693 5.719 0.009 0.000 -0.001
2:WL-U 0.666 41.178 5.063 41.493 -0.066 -0.001 0.007
3:WL- D -0.425 -26.237 -3.226 26.438 0.042 0.001 -0.004
4:WL-X 9.554 -0.552 0.073 9.570 0.001 0.005 0.001
5:WL-Z 0.000 0.294 0.147 0.329 -0.001 0.000 0.000
6:DL+WL UP 0.578 35.501 4.370 35.774 -0.057 -0.001 0.006

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 9 of 166
Job No Sheet No Rev
10
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
7:DL+WLDW -0.513 -31.914 -3.919 32.157 0.051 0.001 -0.005
8:DL+WL-X 9.465 -6.228 -0.621 11.348 0.010 0.006 -0.000
9:DL+WL-Z -0.089 -5.383 -0.546 5.411 0.008 0.000 -0.001
10:DL+WLUP+WL-Z 0.578 35.795 4.517 36.084 -0.057 -0.001 0.006
11:DL+WL DW+WL-Z-0.513 -31.620 -3.772 31.848 0.050 0.001 -0.005
12:DL+WLUP+WL-X10.132 34.950 4.443 36.659 -0.056 0.005 0.007
13:DL+WL DW+WL-X9.041 -32.465 -3.847 33.920 0.052 0.006 -0.004
5 1:DL -0.043 -0.968 0.566 1.123 0.005 0.000 -0.000
2:WL-U 0.326 7.004 -4.078 8.111 -0.034 -0.000 0.003
3:WL- D -0.208 -4.463 2.598 5.168 0.022 0.000 -0.002
4:WL-X 5.176 -0.125 0.185 5.181 0.001 0.005 0.000
5:WL-Z -0.000 0.024 0.073 0.077 -0.000 -0.000 -0.000
6:DL+WL UP 0.283 6.036 -3.512 6.989 -0.029 -0.000 0.003
7:DL+WLDW -0.251 -5.431 3.165 6.291 0.026 0.000 -0.003
8:DL+WL-X 5.133 -1.094 0.751 5.301 0.005 0.005 -0.000
9:DL+WL-Z -0.043 -0.945 0.640 1.142 0.004 0.000 -0.000
10:DL+WLUP+WL-Z 0.283 6.059 -3.438 6.973 -0.029 -0.000 0.003
11:DL+WL DW+WL-Z-0.251 -5.407 3.238 6.308 0.026 0.000 -0.003
12:DL+WLUP+WL-X 5.459 5.910 -3.327 8.706 -0.029 0.004 0.003
13:DL+WL DW+WL-X4.925 -5.556 3.350 8.145 0.027 0.005 -0.002
6 1:DL -0.039 -0.008 0.831 0.832 0.002 -0.000 0.000
2:WL-U 0.237 0.055 -5.993 5.998 -0.012 0.000 -0.000
3:WL- D -0.151 -0.035 3.818 3.821 0.008 -0.000 0.000
4:WL-X 3.942 -0.001 0.218 3.948 0.000 0.004 -0.006
5:WL-Z 0.000 0.000 0.066 0.066 0.000 -0.000 -0.000
6:DL+WL UP 0.198 0.048 -5.162 5.166 -0.010 0.000 -0.000
7:DL+WLDW -0.190 -0.043 4.649 4.653 0.009 -0.000 0.000
8:DL+WL-X 3.903 -0.008 1.049 4.041 0.002 0.004 -0.006
9:DL+WL-Z -0.039 -0.008 0.897 0.898 0.002 -0.000 0.000
10:DL+WLUP+WL-Z 0.198 0.048 -5.095 5.100 -0.010 0.000 -0.000
11:DL+WL DW+WL-Z-0.190 -0.043 4.715 4.720 0.009 -0.000 0.000
12:DL+WLUP+WL-X 4.140 0.047 -4.943 6.448 -0.010 0.005 -0.006
13:DL+WL DW+WL-X3.752 -0.044 4.868 6.146 0.010 0.004 -0.006
7 1:DL -0.054 0.587 0.990 1.152 0.000 0.000 -0.000
2:WL-U 0.335 -4.077 -7.096 8.190 -0.002 -0.001 0.003
3:WL- D -0.213 2.598 4.521 5.219 0.001 0.000 -0.002
4:WL-X 4.137 0.227 0.279 4.153 0.000 -0.028 0.101
5:WL-Z 0.000 -0.020 0.062 0.065 -0.000 0.000 0.000
6:DL+WL UP 0.281 -3.490 -6.106 7.039 -0.001 -0.001 0.002
7:DL+WLDW -0.267 3.185 5.511 6.370 0.001 0.001 -0.002
8:DL+WL-X 4.083 0.814 1.268 4.353 0.001 -0.028 0.100
9:DL+WL-Z -0.054 0.567 1.052 1.196 0.000 0.000 -0.000
10:DL+WLUP+WL-Z 0.281 -3.509 -6.044 6.995 -0.002 -0.001 0.002
11:DL+WL DW+WL-Z-0.267 3.165 5.573 6.414 0.001 0.001 -0.002
12:DL+WLUP+WL-X 4.418 -3.263 -5.827 8.008 -0.001 -0.029 0.103

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 10 of 166
Job No Sheet No Rev
11
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
13:DL+WL DW+WL-X3.870 3.412 5.790 7.755 0.002 -0.027 0.099
8 1:DL -0.037 0.640 1.005 1.192 0.000 -0.000 -0.000
2:WL-U 0.274 -4.351 -7.175 8.395 -0.001 -0.000 0.003
3:WL- D -0.175 2.772 4.572 5.349 0.001 0.000 -0.002
4:WL-X 4.088 0.295 0.298 4.109 0.000 0.000 -0.000
5:WL-Z -0.000 -0.047 0.054 0.072 -0.000 0.000 -0.000
6:DL+WL UP 0.238 -3.711 -6.170 7.204 -0.001 -0.000 0.002
7:DL+WLDW -0.211 3.412 5.576 6.541 0.001 0.000 -0.002
8:DL+WL-X 4.051 0.936 1.303 4.357 0.001 0.000 -0.000
9:DL+WL-Z -0.037 0.593 1.059 1.215 0.000 -0.000 -0.000
10:DL+WLUP+WL-Z 0.238 -3.757 -6.115 7.182 -0.001 -0.000 0.002
11:DL+WL DW+WL-Z-0.211 3.366 5.631 6.563 0.001 0.000 -0.002
12:DL+WLUP+WL-X 4.325 -3.415 -5.872 8.053 -0.001 -0.000 0.002
13:DL+WL DW+WL-X3.876 3.708 5.874 7.955 0.001 0.000 -0.002
9 1:DL -1.165 0.118 -4.944 5.081 0.007 0.000 -0.002
2:WL-U 8.677 -40.630 43.505 60.157 -0.082 -0.002 0.012
3:WL- D -5.529 25.888 -27.720 38.330 0.052 0.002 -0.007
4:WL-X 777.913 0.272 -0.331 777.914 0.001 -0.461 0.522
5:WL-Z 0.000 -16.833 3.602 17.214 -0.014 0.000 0.000
6:DL+WL UP 7.511 -40.512 38.562 56.433 -0.075 -0.002 0.010
7:DL+WLDW -6.694 26.006 -32.664 42.286 0.059 0.002 -0.009
8:DL+WL-X 776.748 0.390 -5.274 776.766 0.008 -0.461 0.521
9:DL+WL-Z -1.165 -16.715 -1.342 16.809 -0.007 0.000 -0.002
10:DL+WLUP+WL-Z 7.512 -57.345 42.164 71.573 -0.089 -0.002 0.010
11:DL+WL DW+WL-Z-6.694 9.173 -29.062 31.202 0.045 0.002 -0.009
12:DL+WLUP+WL-X
785.425 -40.240 38.231 787.384 -0.074 -0.464 0.533
13:DL+WL DW+WL-X
771.219 26.278 -32.994 772.372 0.060 -0.459 0.514
10 1:DL -0.294 -0.022 0.414 0.508 0.001 0.000 -0.000
2:WL-U 1.766 -2.789 -5.879 6.742 -0.002 -0.001 0.003
3:WL- D -1.125 1.777 3.746 4.296 0.001 0.000 -0.002
4:WL-X 110.004 0.012 0.076 110.004 0.000 0.028 0.153
5:WL-Z 0.000 5.987 5.740 8.294 -0.011 0.000 0.000
6:DL+WL UP 1.472 -2.812 -5.465 6.319 -0.001 -0.001 0.002
7:DL+WLDW -1.420 1.755 4.160 4.733 0.002 0.001 -0.002
8:DL+WL-X 109.710 -0.011 0.490 109.711 0.001 0.028 0.153
9:DL+WL-Z -0.294 5.965 6.154 8.575 -0.010 0.000 -0.000
10:DL+WLUP+WL-Z 1.472 3.176 0.275 3.511 -0.012 -0.001 0.002
11:DL+WL DW+WL-Z-1.419 7.742 9.900 12.647 -0.009 0.001 -0.002
12:DL+WLUP+WL-X
111.476 -2.800 -5.389 111.641 -0.000 0.027 0.156
13:DL+WL DW+WL-X
108.585 1.767 4.235 108.681 0.002 0.028 0.151
11 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
2:WL-U 0.000 0.000 0.000 0.000 0.000 0.000 0.000
3:WL- D 0.000 0.000 0.000 0.000 0.000 0.000 0.000
4:WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
5:WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 11 of 166
Job No Sheet No Rev
12
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
6:DL+WL UP 0.000 0.000 0.000 0.000 0.000 0.000 0.000
7:DL+WLDW 0.000 0.000 0.000 0.000 0.000 0.000 0.000
8:DL+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
9:DL+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
10:DL+WLUP+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
11:DL+WL DW+WL-Z0.000 0.000 0.000 0.000 0.000 0.000 0.000
12:DL+WLUP+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
13:DL+WL DW+WL-X0.000 0.000 0.000 0.000 0.000 0.000 0.000
12 1:DL -0.076 -23.413 -5.282 24.001 0.014 0.000 -0.001
2:WL-U 0.575 171.940 38.868 176.280 -0.105 -0.001 0.006
3:WL- D -0.367 -109.555 -24.766 112.320 0.067 0.001 -0.004
4:WL-X 15.009 -0.235 -0.060 15.011 0.000 0.001 0.000
5:WL-Z -0.000 1.276 0.412 1.341 -0.001 0.000 -0.000
6:DL+WL UP 0.499 148.528 33.586 152.278 -0.090 -0.001 0.005
7:DL+WLDW -0.443 -132.968 -30.048 136.321 0.081 0.001 -0.004
8:DL+WL-X 14.933 -23.648 -5.343 28.474 0.014 0.001 -0.000
9:DL+WL-Z -0.076 -22.136 -4.871 22.666 0.013 0.000 -0.001
10:DL+WLUP+WL-Z 0.499 149.804 33.998 153.614 -0.091 -0.001 0.005
11:DL+WL DW+WL-Z-0.443 -131.691 -29.636 134.986 0.080 0.001 -0.004
12:DL+WLUP+WL-X15.508 148.293 33.526 152.824 -0.090 -0.000 0.005
13:DL+WL DW+WL-X
14.567 -133.203 -30.108 137.338 0.081 0.002 -0.004
13 1:DL -0.042 -15.315 -3.115 15.628 0.014 0.000 -0.000
2:WL-U 0.334 112.215 22.887 114.526 -0.100 -0.001 0.004
3:WL- D -0.213 -71.500 -14.583 72.972 0.063 0.000 -0.002
4:WL-X 13.384 -0.142 -0.036 13.385 0.000 -0.118 0.458
5:WL-Z -0.000 0.791 0.282 0.840 -0.001 -0.000 -0.000
6:DL+WL UP 0.292 96.901 19.772 98.898 -0.086 -0.001 0.003
7:DL+WLDW -0.255 -86.815 -17.698 88.601 0.077 0.000 -0.003
8:DL+WL-X 13.342 -15.457 -3.151 20.660 0.014 -0.118 0.457
9:DL+WL-Z -0.042 -14.523 -2.833 14.797 0.013 0.000 -0.000
10:DL+WLUP+WL-Z 0.292 97.692 20.053 99.729 -0.087 -0.001 0.003
11:DL+WL DW+WL-Z-0.255 -86.023 -17.416 87.769 0.076 0.000 -0.003
12:DL+WLUP+WL-X13.677 96.759 19.736 99.694 -0.086 -0.119 0.461
13:DL+WL DW+WL-X
13.129 -86.957 -17.733 89.712 0.077 -0.118 0.455
14 1:DL -0.014 -6.893 -0.865 6.947 0.011 -0.000 -0.000
2:WL-U 0.107 50.371 6.360 50.771 -0.080 0.000 0.001
3:WL- D -0.068 -32.095 -4.053 32.350 0.051 -0.000 -0.001
4:WL-X 9.502 -0.054 -0.012 9.503 0.000 0.004 0.000
5:WL-Z -0.000 0.294 0.147 0.329 -0.001 -0.000 -0.000
6:DL+WL UP 0.093 43.478 5.496 43.824 -0.069 0.000 0.001
7:DL+WLDW -0.082 -38.987 -4.917 39.296 0.062 -0.000 -0.001
8:DL+WL-X 9.488 -6.947 -0.877 11.792 0.011 0.004 0.000
9:DL+WL-Z -0.014 -6.599 -0.717 6.638 0.010 -0.000 -0.000
10:DL+WLUP+WL-Z 0.093 43.772 5.643 44.134 -0.070 0.000 0.001
11:DL+WL DW+WL-Z-0.082 -38.693 -4.770 38.986 0.062 -0.000 -0.001

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 12 of 166
Job No Sheet No Rev
13
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
12:DL+WLUP+WL-X 9.595 43.424 5.484 44.808 -0.069 0.004 0.001
13:DL+WL DW+WL-X9.420 -39.042 -4.929 40.463 0.062 0.004 -0.001
15 1:DL 0.007 -1.172 0.666 1.348 0.006 -0.000 0.000
2:WL-U -0.056 8.544 -4.828 9.814 -0.042 0.000 -0.001
3:WL- D 0.035 -5.444 3.076 6.253 0.026 -0.000 0.000
4:WL-X 5.187 -0.009 0.000 5.187 0.000 0.004 0.000
5:WL-Z 0.000 0.024 0.073 0.077 -0.000 0.000 0.000
6:DL+WL UP -0.048 7.372 -4.162 8.466 -0.036 0.000 -0.000
7:DL+WLDW 0.043 -6.616 3.742 7.601 0.032 -0.000 0.000
8:DL+WL-X 5.194 -1.181 0.666 5.368 0.006 0.004 0.000
9:DL+WL-Z 0.007 -1.149 0.739 1.366 0.005 -0.000 0.000
10:DL+WLUP+WL-Z -0.048 7.396 -4.089 8.451 -0.036 0.000 -0.000
11:DL+WL DW+WL-Z0.043 -6.593 3.815 7.617 0.032 -0.000 0.000
12:DL+WLUP+WL-X 5.139 7.364 -4.162 9.897 -0.036 0.004 -0.000
13:DL+WL DW+WL-X5.230 -6.625 3.742 9.233 0.032 0.003 0.001
16 1:DL 0.011 -0.010 0.986 0.986 0.002 0.000 -0.000
2:WL-U -0.078 0.072 -7.162 7.163 -0.014 -0.000 0.000
3:WL- D 0.049 -0.046 4.564 4.564 0.009 0.000 -0.000
4:WL-X 4.106 0.000 0.003 4.106 0.000 0.004 -0.006
5:WL-Z -0.000 -0.000 0.066 0.066 0.000 0.000 0.000
6:DL+WL UP -0.066 0.062 -6.177 6.177 -0.012 -0.000 0.000
7:DL+WLDW 0.061 -0.056 5.549 5.550 0.011 0.000 -0.000
8:DL+WL-X 4.117 -0.010 0.989 4.234 0.002 0.004 -0.006
9:DL+WL-Z 0.011 -0.010 1.052 1.052 0.002 0.000 -0.000
10:DL+WLUP+WL-Z -0.066 0.062 -6.110 6.111 -0.012 -0.000 0.000
11:DL+WL DW+WL-Z0.061 -0.056 5.616 5.616 0.011 0.000 -0.000
12:DL+WLUP+WL-X 4.040 0.062 -6.174 7.378 -0.012 0.004 -0.006
13:DL+WL DW+WL-X4.167 -0.056 5.552 6.942 0.011 0.004 -0.006
17 1:DL 0.011 0.603 1.150 1.298 0.000 -0.000 0.000
2:WL-U -0.070 -4.187 -8.301 9.298 -0.001 0.000 -0.000
3:WL- D 0.044 2.668 5.289 5.924 0.000 -0.000 0.000
4:WL-X 4.181 0.028 0.010 4.181 0.000 -0.028 0.101
5:WL-Z -0.000 -0.020 0.062 0.065 -0.000 -0.000 -0.000
6:DL+WL UP -0.059 -3.584 -7.151 8.000 -0.000 0.000 -0.000
7:DL+WLDW 0.055 3.271 6.439 7.223 0.001 -0.000 0.000
8:DL+WL-X 4.192 0.631 1.160 4.395 0.000 -0.028 0.101
9:DL+WL-Z 0.011 0.584 1.212 1.345 0.000 -0.000 0.000
10:DL+WLUP+WL-Z -0.059 -3.604 -7.089 7.953 -0.001 0.000 -0.000
11:DL+WL DW+WL-Z0.055 3.252 6.501 7.269 0.000 -0.000 0.000
12:DL+WLUP+WL-X 4.122 -3.556 -7.141 8.980 -0.000 -0.027 0.100
13:DL+WL DW+WL-X4.236 3.299 6.449 8.392 0.001 -0.028 0.101
18 1:DL 0.011 0.614 1.153 1.307 0.000 -0.000 0.000
2:WL-U -0.085 -4.136 -8.290 9.265 0.000 0.000 -0.001
3:WL- D 0.054 2.635 5.282 5.903 -0.000 -0.000 0.001
4:WL-X 4.089 0.041 0.014 4.089 0.000 0.000 -0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 13 of 166
Job No Sheet No Rev
14
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
5:WL-Z 0.000 -0.047 0.054 0.072 -0.000 -0.000 0.000
6:DL+WL UP -0.074 -3.522 -7.137 7.959 0.000 0.000 -0.001
7:DL+WLDW 0.066 3.250 6.436 7.210 -0.000 -0.000 0.001
8:DL+WL-X 4.100 0.656 1.167 4.314 0.000 0.000 0.000
9:DL+WL-Z 0.011 0.568 1.208 1.335 -0.000 -0.000 0.000
10:DL+WLUP+WL-Z -0.074 -3.568 -7.082 7.931 0.000 0.000 -0.001
11:DL+WL DW+WL-Z0.066 3.203 6.490 7.238 -0.000 -0.000 0.001
12:DL+WLUP+WL-X 4.015 -3.480 -7.123 8.886 0.000 0.001 -0.001
13:DL+WL DW+WL-X4.155 3.291 6.450 8.348 -0.000 -0.000 0.001
19 1:DL -0.318 1.259 -6.230 6.364 0.009 0.000 -0.000
2:WL-U 2.421 -49.281 53.236 72.584 -0.100 -0.001 0.004
3:WL- D -1.543 31.400 -33.920 46.248 0.063 0.000 -0.002
4:WL-X 776.894 0.104 -0.082 776.894 0.000 -0.461 0.522
5:WL-Z -0.000 -16.833 3.602 17.214 -0.014 -0.000 -0.000
6:DL+WL UP 2.104 -48.022 47.006 67.231 -0.090 -0.001 0.003
7:DL+WLDW -1.861 32.659 -40.150 51.789 0.073 0.000 -0.003
8:DL+WL-X 776.577 1.363 -6.312 776.603 0.009 -0.461 0.522
9:DL+WL-Z -0.318 -15.574 -2.628 15.797 -0.005 0.000 -0.000
10:DL+WLUP+WL-Z 2.104 -64.855 50.608 82.290 -0.105 -0.001 0.003
11:DL+WL DW+WL-Z-1.861 15.826 -36.548 39.871 0.058 0.000 -0.003
12:DL+WLUP+WL-X
778.998 -47.918 46.924 781.880 -0.090 -0.461 0.525
13:DL+WL DW+WL-X
775.034 32.763 -40.232 776.769 0.073 -0.460 0.520
20 1:DL 0.043 0.105 0.680 0.689 0.001 -0.000 0.000
2:WL-U -0.256 -3.764 -7.901 8.755 -0.001 0.000 -0.000
3:WL- D 0.163 2.398 5.034 5.579 0.000 -0.000 0.000
4:WL-X 110.101 -0.011 -0.027 110.101 0.000 0.028 0.153
5:WL-Z -0.000 5.987 5.740 8.294 -0.011 -0.000 -0.000
6:DL+WL UP -0.213 -3.658 -7.221 8.098 0.000 0.000 -0.000
7:DL+WLDW 0.206 2.503 5.714 6.241 0.001 -0.000 0.000
8:DL+WL-X 110.144 0.094 0.653 110.146 0.001 0.028 0.153
9:DL+WL-Z 0.043 6.092 6.419 8.850 -0.010 -0.000 0.000
10:DL+WLUP+WL-Z -0.213 2.329 -1.481 2.768 -0.011 0.000 -0.000
11:DL+WL DW+WL-Z0.206 8.490 11.454 14.259 -0.010 -0.000 0.000
12:DL+WLUP+WL-X
109.888 -3.669 -7.248 110.188 0.000 0.028 0.153
13:DL+WL DW+WL-X
110.307 2.492 5.687 110.482 0.001 0.028 0.153
21 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
2:WL-U 0.000 0.000 0.000 0.000 0.000 0.000 0.000
3:WL- D 0.000 0.000 0.000 0.000 0.000 0.000 0.000
4:WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
5:WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
6:DL+WL UP 0.000 0.000 0.000 0.000 0.000 0.000 0.000
7:DL+WLDW 0.000 0.000 0.000 0.000 0.000 0.000 0.000
8:DL+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
9:DL+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
10:DL+WLUP+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 14 of 166
Job No Sheet No Rev
15
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
11:DL+WL DW+WL-Z0.000 0.000 0.000 0.000 0.000 0.000 0.000
12:DL+WLUP+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
13:DL+WL DW+WL-X0.000 0.000 0.000 0.000 0.000 0.000 0.000
22 1:DL 0.076 -23.413 -5.282 24.001 0.014 -0.000 0.001
2:WL-U -0.575 171.940 38.868 176.280 -0.105 0.001 -0.006
3:WL- D 0.367 -109.555 -24.766 112.320 0.067 -0.001 0.004
4:WL-X 15.009 0.235 0.060 15.011 -0.000 0.001 0.000
5:WL-Z 0.000 1.276 0.412 1.341 -0.001 -0.000 0.000
6:DL+WL UP -0.499 148.528 33.586 152.278 -0.090 0.001 -0.005
7:DL+WLDW 0.443 -132.968 -30.048 136.321 0.081 -0.001 0.004
8:DL+WL-X 15.085 -23.178 -5.222 28.143 0.014 0.001 0.001
9:DL+WL-Z 0.076 -22.136 -4.871 22.666 0.013 -0.000 0.001
10:DL+WLUP+WL-Z -0.499 149.804 33.998 153.614 -0.091 0.001 -0.005
11:DL+WL DW+WL-Z0.443 -131.691 -29.636 134.986 0.080 -0.001 0.004
12:DL+WLUP+WL-X14.510 148.763 33.647 153.209 -0.091 0.002 -0.005
13:DL+WL DW+WL-X
15.452 -132.733 -29.988 136.952 0.081 0.000 0.005
23 1:DL 0.042 -15.315 -3.115 15.628 0.014 -0.000 0.000
2:WL-U -0.334 112.215 22.887 114.526 -0.100 0.001 -0.004
3:WL- D 0.213 -71.500 -14.583 72.972 0.063 -0.000 0.002
4:WL-X 13.384 0.142 0.036 13.385 -0.000 -0.118 0.458
5:WL-Z 0.000 0.791 0.282 0.840 -0.001 0.000 0.000
6:DL+WL UP -0.292 96.901 19.772 98.898 -0.086 0.001 -0.003
7:DL+WLDW 0.255 -86.815 -17.698 88.601 0.077 -0.000 0.003
8:DL+WL-X 13.426 -15.173 -3.080 20.493 0.013 -0.119 0.458
9:DL+WL-Z 0.042 -14.523 -2.833 14.797 0.013 -0.000 0.000
10:DL+WLUP+WL-Z -0.292 97.692 20.053 99.729 -0.087 0.001 -0.003
11:DL+WL DW+WL-Z0.255 -86.023 -17.416 87.769 0.076 -0.000 0.003
12:DL+WLUP+WL-X13.092 97.043 19.807 99.905 -0.086 -0.118 0.455
13:DL+WL DW+WL-X
13.639 -86.673 -17.662 89.499 0.077 -0.119 0.461
24 1:DL 0.014 -6.893 -0.865 6.947 0.011 0.000 0.000
2:WL-U -0.107 50.371 6.360 50.771 -0.080 -0.000 -0.001
3:WL- D 0.068 -32.095 -4.053 32.350 0.051 0.000 0.001
4:WL-X 9.502 0.054 0.012 9.503 -0.000 0.004 0.000
5:WL-Z 0.000 0.294 0.147 0.329 -0.001 0.000 0.000
6:DL+WL UP -0.093 43.478 5.496 43.824 -0.069 -0.000 -0.001
7:DL+WLDW 0.082 -38.987 -4.917 39.296 0.062 0.000 0.001
8:DL+WL-X 9.516 -6.838 -0.853 11.750 0.011 0.004 0.000
9:DL+WL-Z 0.014 -6.599 -0.717 6.638 0.010 0.000 0.000
10:DL+WLUP+WL-Z -0.093 43.772 5.643 44.134 -0.070 -0.000 -0.001
11:DL+WL DW+WL-Z0.082 -38.693 -4.770 38.986 0.062 0.000 0.001
12:DL+WLUP+WL-X 9.410 43.532 5.508 44.877 -0.070 0.004 -0.001
13:DL+WL DW+WL-X9.584 -38.933 -4.905 40.394 0.062 0.004 0.001
25 1:DL -0.007 -1.172 0.666 1.348 0.006 0.000 -0.000
2:WL-U 0.056 8.544 -4.828 9.814 -0.042 -0.000 0.001
3:WL- D -0.035 -5.444 3.076 6.253 0.026 0.000 -0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 15 of 166
Job No Sheet No Rev
16
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
4:WL-X 5.187 0.009 -0.000 5.187 -0.000 0.004 0.000
5:WL-Z -0.000 0.024 0.073 0.077 -0.000 -0.000 -0.000
6:DL+WL UP 0.048 7.372 -4.162 8.466 -0.036 -0.000 0.000
7:DL+WLDW -0.043 -6.616 3.742 7.601 0.032 0.000 -0.000
8:DL+WL-X 5.180 -1.164 0.665 5.350 0.006 0.004 0.000
9:DL+WL-Z -0.007 -1.149 0.739 1.366 0.005 0.000 -0.000
10:DL+WLUP+WL-Z 0.048 7.396 -4.089 8.451 -0.036 -0.000 0.000
11:DL+WL DW+WL-Z-0.043 -6.593 3.815 7.617 0.032 0.000 -0.000
12:DL+WLUP+WL-X 5.235 7.381 -4.163 9.961 -0.036 0.003 0.001
13:DL+WL DW+WL-X5.144 -6.608 3.741 9.172 0.032 0.004 -0.000
26 1:DL -0.011 -0.010 0.986 0.986 0.002 -0.000 0.000
2:WL-U 0.078 0.072 -7.162 7.163 -0.014 0.000 -0.000
3:WL- D -0.049 -0.046 4.564 4.564 0.009 -0.000 0.000
4:WL-X 4.106 -0.000 -0.003 4.106 -0.000 0.004 -0.006
5:WL-Z 0.000 -0.000 0.066 0.066 0.000 -0.000 -0.000
6:DL+WL UP 0.066 0.062 -6.177 6.177 -0.012 0.000 -0.000
7:DL+WLDW -0.061 -0.056 5.549 5.550 0.011 -0.000 0.000
8:DL+WL-X 4.095 -0.010 0.983 4.211 0.002 0.004 -0.006
9:DL+WL-Z -0.011 -0.010 1.052 1.052 0.002 -0.000 0.000
10:DL+WLUP+WL-Z 0.066 0.062 -6.110 6.111 -0.012 0.000 -0.000
11:DL+WL DW+WL-Z-0.061 -0.056 5.616 5.616 0.011 -0.000 0.000
12:DL+WLUP+WL-X 4.172 0.062 -6.179 7.456 -0.012 0.004 -0.006
13:DL+WL DW+WL-X4.045 -0.056 5.547 6.865 0.011 0.004 -0.006
27 1:DL -0.011 0.603 1.150 1.298 0.000 0.000 -0.000
2:WL-U 0.070 -4.187 -8.301 9.298 -0.001 -0.000 0.000
3:WL- D -0.044 2.668 5.289 5.924 0.000 0.000 -0.000
4:WL-X 4.181 -0.028 -0.010 4.181 -0.000 -0.028 0.101
5:WL-Z 0.000 -0.020 0.062 0.065 -0.000 0.000 0.000
6:DL+WL UP 0.059 -3.584 -7.151 8.000 -0.000 -0.000 0.000
7:DL+WLDW -0.055 3.271 6.439 7.223 0.001 0.000 -0.000
8:DL+WL-X 4.171 0.575 1.139 4.362 0.000 -0.028 0.100
9:DL+WL-Z -0.011 0.584 1.212 1.345 0.000 0.000 -0.000
10:DL+WLUP+WL-Z 0.059 -3.604 -7.089 7.953 -0.001 -0.000 0.000
11:DL+WL DW+WL-Z-0.055 3.252 6.501 7.269 0.000 0.000 -0.000
12:DL+WLUP+WL-X 4.240 -3.612 -7.162 9.073 -0.000 -0.028 0.101
13:DL+WL DW+WL-X4.126 3.243 6.429 8.299 0.000 -0.027 0.100
28 1:DL -0.011 0.614 1.153 1.307 0.000 0.000 -0.000
2:WL-U 0.085 -4.136 -8.290 9.265 0.000 -0.000 0.001
3:WL- D -0.054 2.635 5.282 5.903 -0.000 0.000 -0.001
4:WL-X 4.089 -0.041 -0.014 4.089 -0.000 0.000 -0.000
5:WL-Z -0.000 -0.047 0.054 0.072 -0.000 0.000 -0.000
6:DL+WL UP 0.074 -3.522 -7.137 7.959 0.000 -0.000 0.001
7:DL+WLDW -0.066 3.250 6.436 7.210 -0.000 0.000 -0.001
8:DL+WL-X 4.078 0.573 1.139 4.272 -0.000 0.000 -0.000
9:DL+WL-Z -0.011 0.568 1.208 1.335 -0.000 0.000 -0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 16 of 166
Job No Sheet No Rev
17
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
10:DL+WLUP+WL-Z 0.074 -3.568 -7.082 7.931 0.000 -0.000 0.001
11:DL+WL DW+WL-Z-0.066 3.203 6.490 7.238 -0.000 0.000 -0.001
12:DL+WLUP+WL-X 4.163 -3.563 -7.151 9.009 0.000 -0.000 0.001
13:DL+WL DW+WL-X4.023 3.208 6.422 8.229 -0.000 0.000 -0.001
29 1:DL 0.318 1.259 -6.230 6.364 0.009 -0.000 0.000
2:WL-U -2.421 -49.281 53.236 72.584 -0.100 0.001 -0.004
3:WL- D 1.543 31.400 -33.920 46.248 0.063 -0.000 0.002
4:WL-X 776.894 -0.104 0.082 776.894 -0.000 -0.461 0.522
5:WL-Z 0.000 -16.833 3.602 17.214 -0.014 0.000 0.000
6:DL+WL UP -2.104 -48.022 47.006 67.231 -0.090 0.001 -0.003
7:DL+WLDW 1.861 32.659 -40.150 51.789 0.073 -0.000 0.003
8:DL+WL-X 777.212 1.155 -6.148 777.237 0.009 -0.461 0.523
9:DL+WL-Z 0.318 -15.574 -2.628 15.797 -0.005 -0.000 0.000
10:DL+WLUP+WL-Z -2.104 -64.855 50.608 82.290 -0.105 0.001 -0.003
11:DL+WL DW+WL-Z1.861 15.826 -36.548 39.871 0.058 -0.000 0.003
12:DL+WLUP+WL-X
774.791 -48.126 47.088 777.711 -0.091 -0.460 0.519
13:DL+WL DW+WL-X
778.755 32.555 -40.068 780.464 0.072 -0.461 0.525
30 1:DL -0.043 0.105 0.680 0.689 0.001 0.000 -0.000
2:WL-U 0.256 -3.764 -7.901 8.755 -0.001 -0.000 0.000
3:WL- D -0.163 2.398 5.034 5.579 0.000 0.000 -0.000
4:WL-X 110.101 0.011 0.027 110.101 -0.000 0.028 0.153
5:WL-Z 0.000 5.987 5.740 8.294 -0.011 0.000 0.000
6:DL+WL UP 0.213 -3.658 -7.221 8.098 0.000 -0.000 0.000
7:DL+WLDW -0.206 2.503 5.714 6.241 0.001 0.000 -0.000
8:DL+WL-X 110.057 0.116 0.706 110.060 0.001 0.028 0.153
9:DL+WL-Z -0.043 6.092 6.419 8.850 -0.010 0.000 -0.000
10:DL+WLUP+WL-Z 0.213 2.329 -1.481 2.768 -0.011 -0.000 0.000
11:DL+WL DW+WL-Z-0.206 8.490 11.454 14.259 -0.010 0.000 -0.000
12:DL+WLUP+WL-X
110.313 -3.647 -7.195 110.608 0.000 0.028 0.153
13:DL+WL DW+WL-X
109.894 2.514 5.740 110.073 0.001 0.028 0.153
31 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
2:WL-U 0.000 0.000 0.000 0.000 0.000 0.000 0.000
3:WL- D 0.000 0.000 0.000 0.000 0.000 0.000 0.000
4:WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
5:WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
6:DL+WL UP 0.000 0.000 0.000 0.000 0.000 0.000 0.000
7:DL+WLDW 0.000 0.000 0.000 0.000 0.000 0.000 0.000
8:DL+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
9:DL+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
10:DL+WLUP+WL-Z 0.000 0.000 0.000 0.000 0.000 0.000 0.000
11:DL+WL DW+WL-Z0.000 0.000 0.000 0.000 0.000 0.000 0.000
12:DL+WLUP+WL-X 0.000 0.000 0.000 0.000 0.000 0.000 0.000
13:DL+WL DW+WL-X0.000 0.000 0.000 0.000 0.000 0.000 0.000
32 1:DL 0.212 -19.307 -4.338 19.789 0.012 -0.000 0.002
2:WL-U -1.602 140.882 31.724 144.419 -0.086 0.003 -0.016

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 17 of 166
Job No Sheet No Rev
18
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
3:WL- D 1.021 -89.766 -20.214 92.019 0.055 -0.002 0.010
4:WL-X 15.063 1.598 0.207 15.149 -0.001 0.001 0.001
5:WL-Z 0.000 1.277 0.412 1.341 -0.001 0.000 0.000
6:DL+WL UP -1.391 121.575 27.386 124.629 -0.074 0.003 -0.014
7:DL+WLDW 1.233 -109.072 -24.552 111.808 0.066 -0.002 0.012
8:DL+WL-X 15.274 -17.709 -4.131 23.748 0.011 0.001 0.003
9:DL+WL-Z 0.212 -18.030 -3.926 18.454 0.011 -0.000 0.002
10:DL+WLUP+WL-Z -1.391 122.852 27.798 125.965 -0.075 0.003 -0.014
11:DL+WL DW+WL-Z1.233 -107.796 -24.140 110.473 0.066 -0.002 0.012
12:DL+WLUP+WL-X13.672 123.173 27.593 126.964 -0.075 0.004 -0.013
13:DL+WL DW+WL-X
16.295 -107.474 -24.345 111.395 0.066 -0.001 0.013
33 1:DL 0.163 -12.623 -2.549 12.879 0.011 -0.000 0.002
2:WL-U -1.119 91.861 18.607 93.734 -0.082 0.002 -0.012
3:WL- D 0.713 -58.531 -11.856 59.724 0.052 -0.002 0.007
4:WL-X 13.562 1.098 0.073 13.607 -0.001 -0.119 0.458
5:WL-Z -0.000 0.791 0.282 0.840 -0.001 -0.000 -0.000
6:DL+WL UP -0.955 79.239 16.058 80.855 -0.070 0.002 -0.010
7:DL+WLDW 0.876 -71.154 -14.405 72.603 0.063 -0.002 0.009
8:DL+WL-X 13.726 -11.525 -2.476 18.093 0.010 -0.119 0.460
9:DL+WL-Z 0.163 -11.831 -2.268 12.048 0.010 -0.000 0.002
10:DL+WLUP+WL-Z -0.956 80.030 16.339 81.687 -0.071 0.002 -0.010
11:DL+WL DW+WL-Z0.876 -70.362 -14.123 71.771 0.062 -0.002 0.009
12:DL+WLUP+WL-X12.607 80.337 16.131 82.904 -0.071 -0.117 0.448
13:DL+WL DW+WL-X
14.438 -70.056 -14.332 72.950 0.062 -0.121 0.467
34 1:DL 0.089 -5.676 -0.693 5.719 0.009 -0.000 0.001
2:WL-U -0.666 41.178 5.063 41.493 -0.066 0.001 -0.007
3:WL- D 0.425 -26.237 -3.226 26.438 0.042 -0.001 0.004
4:WL-X 9.554 0.552 -0.073 9.570 -0.001 0.005 0.001
5:WL-Z -0.000 0.294 0.147 0.329 -0.001 -0.000 -0.000
6:DL+WL UP -0.578 35.501 4.370 35.774 -0.057 0.001 -0.006
7:DL+WLDW 0.513 -31.914 -3.919 32.157 0.051 -0.001 0.005
8:DL+WL-X 9.643 -5.125 -0.766 10.947 0.008 0.005 0.002
9:DL+WL-Z 0.089 -5.383 -0.546 5.411 0.008 -0.000 0.001
10:DL+WLUP+WL-Z -0.578 35.795 4.517 36.084 -0.057 0.001 -0.006
11:DL+WL DW+WL-Z0.513 -31.620 -3.772 31.848 0.050 -0.001 0.005
12:DL+WLUP+WL-X 8.976 36.053 4.298 37.402 -0.058 0.006 -0.005
13:DL+WL DW+WL-X
10.067 -31.362 -3.992 33.179 0.050 0.005 0.006
35 1:DL 0.043 -0.968 0.566 1.123 0.005 -0.000 0.000
2:WL-U -0.326 7.004 -4.078 8.111 -0.034 0.000 -0.003
3:WL- D 0.208 -4.463 2.598 5.168 0.022 -0.000 0.002
4:WL-X 5.176 0.125 -0.185 5.181 -0.001 0.005 0.000
5:WL-Z 0.000 0.024 0.073 0.077 -0.000 0.000 0.000
6:DL+WL UP -0.283 6.036 -3.512 6.989 -0.029 0.000 -0.003
7:DL+WLDW 0.251 -5.431 3.165 6.291 0.026 -0.000 0.003
8:DL+WL-X 5.219 -0.843 0.381 5.300 0.004 0.005 0.001

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 18 of 166
Job No Sheet No Rev
19
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
9:DL+WL-Z 0.043 -0.945 0.640 1.142 0.004 -0.000 0.000
10:DL+WLUP+WL-Z -0.283 6.059 -3.438 6.973 -0.029 0.000 -0.003
11:DL+WL DW+WL-Z0.251 -5.407 3.238 6.308 0.026 -0.000 0.003
12:DL+WLUP+WL-X 4.892 6.161 -3.697 8.693 -0.030 0.005 -0.003
13:DL+WL DW+WL-X5.427 -5.306 2.980 8.153 0.026 0.004 0.003
36 1:DL 0.039 -0.008 0.831 0.832 0.002 0.000 -0.000
2:WL-U -0.237 0.055 -5.993 5.998 -0.012 -0.000 0.000
3:WL- D 0.151 -0.035 3.818 3.821 0.008 0.000 -0.000
4:WL-X 3.942 0.001 -0.218 3.948 -0.000 0.004 -0.006
5:WL-Z -0.000 0.000 0.066 0.066 0.000 0.000 0.000
6:DL+WL UP -0.198 0.048 -5.162 5.166 -0.010 -0.000 0.000
7:DL+WLDW 0.190 -0.043 4.649 4.653 0.009 0.000 -0.000
8:DL+WL-X 3.981 -0.007 0.612 4.028 0.001 0.004 -0.006
9:DL+WL-Z 0.039 -0.008 0.897 0.898 0.002 0.000 -0.000
10:DL+WLUP+WL-Z -0.198 0.048 -5.095 5.100 -0.010 -0.000 0.000
11:DL+WL DW+WL-Z0.190 -0.043 4.715 4.720 0.009 0.000 -0.000
12:DL+WLUP+WL-X 3.744 0.048 -5.380 6.555 -0.011 0.004 -0.006
13:DL+WL DW+WL-X4.132 -0.043 4.431 6.059 0.009 0.005 -0.006
37 1:DL 0.054 0.587 0.990 1.152 0.000 -0.000 0.000
2:WL-U -0.335 -4.077 -7.096 8.190 -0.002 0.001 -0.003
3:WL- D 0.213 2.598 4.521 5.219 0.001 -0.000 0.002
4:WL-X 4.137 -0.227 -0.279 4.153 -0.000 -0.028 0.101
5:WL-Z -0.000 -0.020 0.062 0.065 -0.000 -0.000 -0.000
6:DL+WL UP -0.281 -3.490 -6.106 7.038 -0.001 0.001 -0.002
7:DL+WLDW 0.267 3.185 5.511 6.370 0.001 -0.001 0.002
8:DL+WL-X 4.191 0.360 0.711 4.266 0.000 -0.028 0.101
9:DL+WL-Z 0.054 0.567 1.052 1.196 0.000 -0.000 0.000
10:DL+WLUP+WL-Z -0.281 -3.509 -6.044 6.995 -0.002 0.001 -0.002
11:DL+WL DW+WL-Z0.267 3.165 5.573 6.414 0.001 -0.001 0.002
12:DL+WLUP+WL-X 3.856 -3.717 -6.385 8.334 -0.002 -0.027 0.098
13:DL+WL DW+WL-X4.404 2.958 5.232 7.451 0.001 -0.028 0.103
38 1:DL 0.037 0.640 1.005 1.192 0.000 0.000 0.000
2:WL-U -0.274 -4.351 -7.175 8.395 -0.001 0.000 -0.003
3:WL- D 0.175 2.772 4.572 5.349 0.001 -0.000 0.002
4:WL-X 4.088 -0.295 -0.298 4.109 -0.000 0.000 -0.000
5:WL-Z 0.000 -0.047 0.054 0.072 -0.000 -0.000 0.000
6:DL+WL UP -0.238 -3.711 -6.170 7.204 -0.001 0.000 -0.002
7:DL+WLDW 0.211 3.412 5.576 6.541 0.001 -0.000 0.002
8:DL+WL-X 4.124 0.345 0.707 4.198 -0.000 0.000 0.000
9:DL+WL-Z 0.037 0.593 1.059 1.215 0.000 0.000 0.000
10:DL+WLUP+WL-Z -0.238 -3.757 -6.115 7.182 -0.001 0.000 -0.002
11:DL+WL DW+WL-Z0.211 3.366 5.631 6.563 0.001 -0.000 0.002
12:DL+WLUP+WL-X 3.850 -4.006 -6.468 8.527 -0.001 0.000 -0.002
13:DL+WL DW+WL-X4.299 3.117 5.278 7.487 0.001 -0.000 0.002
39 1:DL 1.165 0.118 -4.944 5.081 0.007 -0.000 0.002

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 19 of 166
Job No Sheet No Rev
20
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
2:WL-U -8.677 -40.630 43.505 60.157 -0.082 0.002 -0.012
3:WL- D 5.529 25.888 -27.720 38.330 0.052 -0.002 0.007
4:WL-X 777.913 -0.272 0.331 777.914 -0.001 -0.461 0.522
5:WL-Z -0.000 -16.833 3.602 17.214 -0.014 -0.000 -0.000
6:DL+WL UP -7.511 -40.512 38.562 56.433 -0.075 0.002 -0.010
7:DL+WLDW 6.694 26.006 -32.664 42.286 0.059 -0.002 0.009
8:DL+WL-X 779.079 -0.154 -4.613 779.092 0.006 -0.462 0.524
9:DL+WL-Z 1.165 -16.715 -1.342 16.809 -0.007 -0.000 0.002
10:DL+WLUP+WL-Z -7.512 -57.345 42.164 71.573 -0.089 0.002 -0.010
11:DL+WL DW+WL-Z6.694 9.173 -29.062 31.202 0.045 -0.002 0.009
12:DL+WLUP+WL-X
770.402 -40.784 38.892 772.460 -0.076 -0.459 0.512
13:DL+WL DW+WL-X
784.607 25.735 -32.333 785.695 0.058 -0.463 0.531
40 1:DL 0.294 -0.022 0.414 0.508 0.001 -0.000 0.000
2:WL-U -1.766 -2.789 -5.879 6.742 -0.002 0.001 -0.003
3:WL- D 1.125 1.777 3.746 4.296 0.001 -0.000 0.002
4:WL-X 110.004 -0.012 -0.076 110.004 -0.000 0.028 0.153
5:WL-Z -0.000 5.987 5.740 8.294 -0.011 -0.000 -0.000
6:DL+WL UP -1.472 -2.812 -5.465 6.319 -0.001 0.001 -0.002
7:DL+WLDW 1.420 1.755 4.160 4.733 0.002 -0.001 0.002
8:DL+WL-X 110.298 -0.034 0.338 110.299 0.001 0.028 0.154
9:DL+WL-Z 0.294 5.965 6.154 8.575 -0.010 -0.000 0.000
10:DL+WLUP+WL-Z -1.472 3.176 0.275 3.511 -0.012 0.001 -0.002
11:DL+WL DW+WL-Z1.419 7.742 9.900 12.647 -0.009 -0.001 0.002
12:DL+WLUP+WL-X
108.532 -2.823 -5.541 108.710 -0.001 0.028 0.151
13:DL+WL DW+WL-X
111.424 1.743 4.084 111.512 0.002 0.027 0.156
41 1:DL -0.194 -17.573 -3.926 18.007 0.012 0.000 -0.002
2:WL-U 1.468 127.787 28.983 131.041 -0.086 -0.003 0.015
3:WL- D -0.935 -81.422 -18.467 83.495 0.055 0.002 -0.009
4:WL-X 15.063 -2.364 0.714 15.264 0.001 0.001 0.001
5:WL-Z -0.000 1.277 0.411 1.341 -0.001 -0.000 -0.000
6:DL+WL UP 1.274 110.214 25.057 113.033 -0.074 -0.003 0.013
7:DL+WLDW -1.130 -98.995 -22.393 101.502 0.066 0.002 -0.011
8:DL+WL-X 14.868 -19.937 -3.212 25.077 0.013 0.002 -0.001
9:DL+WL-Z -0.194 -16.296 -3.515 16.672 0.011 0.000 -0.002
10:DL+WLUP+WL-Z 1.274 111.491 25.468 114.369 -0.075 -0.003 0.013
11:DL+WL DW+WL-Z-1.130 -97.718 -21.982 100.167 0.066 0.002 -0.011
12:DL+WLUP+WL-X16.336 107.850 25.772 112.083 -0.073 -0.002 0.014
13:DL+WL DW+WL-X
13.933 -101.359 -21.679 104.584 0.067 0.004 -0.010
42 1:DL -0.071 -5.020 -0.620 5.059 0.009 0.000 -0.001
2:WL-U 0.532 36.274 4.263 36.528 -0.066 -0.001 0.005
3:WL- D -0.339 -23.113 -2.716 23.274 0.042 0.001 -0.003
4:WL-X 9.554 -1.216 4.855 10.786 0.001 0.005 0.001
5:WL-Z 0.000 0.294 0.148 0.329 -0.001 0.000 0.000
6:DL+WL UP 0.461 31.254 3.642 31.469 -0.057 -0.001 0.005
7:DL+WLDW -0.410 -28.133 -3.336 28.333 0.051 0.001 -0.004

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 20 of 166
Job No Sheet No Rev
21
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
8:DL+WL-X 9.483 -6.236 4.235 12.114 0.010 0.006 0.000
9:DL+WL-Z -0.071 -4.726 -0.472 4.750 0.008 0.000 -0.001
10:DL+WLUP+WL-Z 0.461 31.548 3.790 31.778 -0.057 -0.001 0.005
11:DL+WL DW+WL-Z-0.410 -27.839 -3.188 28.024 0.050 0.001 -0.004
12:DL+WLUP+WL-X10.015 30.038 8.497 32.784 -0.056 0.005 0.005
13:DL+WL DW+WL-X9.144 -29.349 1.519 30.778 0.052 0.006 -0.003
43 1:DL -0.026 -0.705 0.645 0.956 0.005 0.000 -0.000
2:WL-U 0.192 5.037 -4.445 6.721 -0.034 -0.000 0.002
3:WL- D -0.122 -3.210 2.832 4.282 0.022 0.000 -0.001
4:WL-X 5.176 -0.279 4.349 6.766 0.001 0.005 0.000
5:WL-Z -0.000 0.024 0.073 0.077 -0.000 -0.000 -0.000
6:DL+WL UP 0.166 4.332 -3.800 5.765 -0.029 -0.000 0.002
7:DL+WLDW -0.148 -3.915 3.477 5.238 0.026 0.000 -0.002
8:DL+WL-X 5.150 -0.984 4.994 7.241 0.005 0.005 -0.000
9:DL+WL-Z -0.026 -0.682 0.718 0.991 0.004 0.000 -0.000
10:DL+WLUP+WL-Z 0.166 4.356 -3.726 5.735 -0.029 -0.000 0.002
11:DL+WL DW+WL-Z-0.148 -3.891 3.550 5.270 0.026 0.000 -0.002
12:DL+WLUP+WL-X 5.342 4.053 0.549 6.728 -0.029 0.004 0.002
13:DL+WL DW+WL-X5.028 -4.194 7.826 10.204 0.027 0.005 -0.001
44 1:DL -0.019 0.845 0.989 1.301 0.000 -0.000 -0.000
2:WL-U 0.140 -5.855 -7.405 9.441 -0.001 -0.000 0.001
3:WL- D -0.089 3.731 4.718 6.016 0.001 0.000 -0.001
4:WL-X 4.088 0.310 0.416 4.120 0.000 0.000 -0.000
5:WL-Z -0.000 -0.047 0.055 0.072 -0.000 0.000 -0.000
6:DL+WL UP 0.121 -5.010 -6.416 8.141 -0.001 -0.000 0.001
7:DL+WLDW -0.108 4.576 5.708 7.316 0.001 0.000 -0.001
8:DL+WL-X 4.068 1.155 1.405 4.456 0.001 0.000 -0.000
9:DL+WL-Z -0.019 0.798 1.044 1.314 0.000 -0.000 -0.000
10:DL+WLUP+WL-Z 0.121 -5.057 -6.361 8.127 -0.001 -0.000 0.001
11:DL+WL DW+WL-Z-0.108 4.529 5.762 7.330 0.001 0.000 -0.001
12:DL+WLUP+WL-X 4.208 -4.700 -6.001 8.707 -0.001 -0.000 0.001
13:DL+WL DW+WL-X3.979 4.886 6.123 8.786 0.001 0.000 -0.001
45 1:DL 0.194 -17.573 -3.926 18.007 0.012 -0.000 0.002
2:WL-U -1.468 127.787 28.983 131.041 -0.086 0.003 -0.015
3:WL- D 0.935 -81.422 -18.467 83.495 0.055 -0.002 0.009
4:WL-X 15.063 2.364 -0.714 15.264 -0.001 0.001 0.001
5:WL-Z 0.000 1.277 0.411 1.341 -0.001 0.000 0.000
6:DL+WL UP -1.274 110.214 25.057 113.033 -0.074 0.003 -0.013
7:DL+WLDW 1.130 -98.995 -22.393 101.502 0.066 -0.002 0.011
8:DL+WL-X 15.257 -15.209 -4.640 22.037 0.011 0.001 0.003
9:DL+WL-Z 0.194 -16.296 -3.515 16.672 0.011 -0.000 0.002
10:DL+WLUP+WL-Z -1.274 111.491 25.468 114.369 -0.075 0.003 -0.013
11:DL+WL DW+WL-Z1.130 -97.718 -21.982 100.167 0.066 -0.002 0.011
12:DL+WLUP+WL-X13.789 112.578 24.343 116.002 -0.075 0.004 -0.012
13:DL+WL DW+WL-X
16.192 -96.631 -23.107 100.666 0.066 -0.001 0.012

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 21 of 166
Job No Sheet No Rev
22
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
46 1:DL 0.071 -5.020 -0.620 5.059 0.009 -0.000 0.001
2:WL-U -0.532 36.274 4.263 36.528 -0.066 0.001 -0.005
3:WL- D 0.339 -23.113 -2.716 23.274 0.042 -0.001 0.003
4:WL-X 9.554 1.216 -4.855 10.786 -0.001 0.005 0.001
5:WL-Z -0.000 0.294 0.148 0.329 -0.001 -0.000 -0.000
6:DL+WL UP -0.461 31.254 3.642 31.469 -0.057 0.001 -0.005
7:DL+WLDW 0.410 -28.133 -3.336 28.333 0.051 -0.001 0.004
8:DL+WL-X 9.625 -3.803 -5.475 11.709 0.008 0.005 0.001
9:DL+WL-Z 0.071 -4.726 -0.472 4.750 0.008 -0.000 0.001
10:DL+WLUP+WL-Z -0.461 31.548 3.790 31.778 -0.057 0.001 -0.005
11:DL+WL DW+WL-Z0.410 -27.839 -3.188 28.024 0.050 -0.001 0.004
12:DL+WLUP+WL-X 9.093 32.471 -1.212 33.742 -0.058 0.006 -0.004
13:DL+WL DW+WL-X9.964 -26.916 -8.191 29.847 0.050 0.005 0.005
47 1:DL 0.026 -0.705 0.645 0.956 0.005 -0.000 0.000
2:WL-U -0.192 5.037 -4.445 6.721 -0.034 0.000 -0.002
3:WL- D 0.122 -3.210 2.832 4.282 0.022 -0.000 0.001
4:WL-X 5.176 0.279 -4.349 6.766 -0.001 0.005 0.000
5:WL-Z 0.000 0.024 0.073 0.077 -0.000 0.000 0.000
6:DL+WL UP -0.166 4.332 -3.800 5.765 -0.029 0.000 -0.002
7:DL+WLDW 0.148 -3.915 3.477 5.238 0.026 -0.000 0.002
8:DL+WL-X 5.201 -0.426 -3.704 6.400 0.004 0.005 0.000
9:DL+WL-Z 0.026 -0.682 0.718 0.991 0.004 -0.000 0.000
10:DL+WLUP+WL-Z -0.166 4.356 -3.726 5.735 -0.029 0.000 -0.002
11:DL+WL DW+WL-Z0.148 -3.891 3.550 5.270 0.026 -0.000 0.002
12:DL+WLUP+WL-X 5.009 4.611 -8.149 10.619 -0.030 0.005 -0.002
13:DL+WL DW+WL-X5.324 -3.636 -0.872 6.506 0.026 0.004 0.002
48 1:DL 0.019 0.845 0.989 1.301 0.000 0.000 0.000
2:WL-U -0.140 -5.855 -7.405 9.441 -0.001 0.000 -0.001
3:WL- D 0.089 3.731 4.718 6.016 0.001 -0.000 0.001
4:WL-X 4.088 -0.310 -0.416 4.120 -0.000 0.000 -0.000
5:WL-Z 0.000 -0.047 0.055 0.072 -0.000 -0.000 0.000
6:DL+WL UP -0.121 -5.010 -6.416 8.141 -0.001 0.000 -0.001
7:DL+WLDW 0.108 4.576 5.708 7.316 0.001 -0.000 0.001
8:DL+WL-X 4.107 0.535 0.574 4.181 -0.000 0.000 0.000
9:DL+WL-Z 0.019 0.798 1.044 1.314 0.000 0.000 0.000
10:DL+WLUP+WL-Z -0.121 -5.057 -6.361 8.127 -0.001 0.000 -0.001
11:DL+WL DW+WL-Z0.108 4.529 5.762 7.330 0.001 -0.000 0.001
12:DL+WLUP+WL-X 3.967 -5.320 -6.832 9.524 -0.001 0.000 -0.001
13:DL+WL DW+WL-X4.196 4.266 5.292 7.988 0.001 -0.000 0.001
49 1:DL 0.005 0.191 1.165 1.181 -0.000 -0.000 0.000
2:WL-U -0.037 -0.959 -8.325 8.380 0.006 0.000 -0.000
3:WL- D 0.023 0.611 5.304 5.339 -0.004 -0.000 0.000
4:WL-X 4.077 0.166 -0.001 4.080 0.002 0.000 -0.000
5:WL-Z -0.000 -0.047 0.046 0.065 -0.000 -0.000 -0.000
6:DL+WL UP -0.032 -0.768 -7.160 7.201 0.006 0.000 -0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 22 of 166
Job No Sheet No Rev
23
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
7:DL+WLDW 0.028 0.802 6.469 6.519 -0.004 -0.000 0.000
8:DL+WL-X 4.082 0.358 1.164 4.260 0.002 0.000 -0.000
9:DL+WL-Z 0.005 0.144 1.211 1.219 -0.000 -0.000 0.000
10:DL+WLUP+WL-Z -0.032 -0.815 -7.114 7.161 0.006 0.000 -0.000
11:DL+WL DW+WL-Z0.028 0.756 6.515 6.559 -0.004 -0.000 0.000
12:DL+WLUP+WL-X 4.045 -0.602 -7.161 8.246 0.008 0.001 -0.000
13:DL+WL DW+WL-X4.105 0.969 6.468 7.722 -0.002 -0.000 0.000
50 1:DL -0.002 -1.509 0.706 1.666 0.003 -0.000 -0.000
2:WL-U 0.013 11.125 -5.056 12.220 -0.027 0.001 0.000
3:WL- D -0.008 -7.088 3.221 7.786 0.017 -0.001 -0.000
4:WL-X 5.156 -0.095 -0.072 5.157 -0.001 -0.002 -0.000
5:WL-Z -0.000 0.024 0.065 0.069 -0.000 0.000 0.000
6:DL+WL UP 0.012 9.616 -4.350 10.554 -0.024 0.001 0.000
7:DL+WLDW -0.010 -8.597 3.927 9.452 0.021 -0.001 -0.000
8:DL+WL-X 5.154 -1.603 0.634 5.435 0.002 -0.002 -0.000
9:DL+WL-Z -0.002 -1.485 0.770 1.673 0.003 -0.000 -0.000
10:DL+WLUP+WL-Z 0.012 9.640 -4.286 10.549 -0.024 0.001 0.000
11:DL+WL DW+WL-Z-0.010 -8.574 3.992 9.457 0.020 -0.001 -0.000
12:DL+WLUP+WL-X 5.168 9.522 -4.422 11.701 -0.026 -0.001 0.000
13:DL+WL DW+WL-X5.146 -8.692 3.855 10.812 0.019 -0.003 -0.000
51 1:DL -0.148 -22.096 -4.977 22.650 0.013 0.000 -0.001
2:WL-U 1.120 162.012 36.535 166.084 -0.099 -0.002 0.011
3:WL- D -0.714 -103.229 -23.279 105.823 0.063 0.001 -0.007
4:WL-X 15.017 -0.733 -0.376 15.040 0.002 -0.000 0.000
5:WL-Z -0.000 1.276 0.417 1.343 -0.001 0.000 -0.000
6:DL+WL UP 0.972 139.916 31.558 143.434 -0.086 -0.002 0.010
7:DL+WLDW -0.862 -125.325 -28.256 128.473 0.076 0.001 -0.009
8:DL+WL-X 14.869 -22.828 -5.354 27.765 0.015 -0.000 -0.001
9:DL+WL-Z -0.148 -20.819 -4.560 21.313 0.012 0.000 -0.001
10:DL+WLUP+WL-Z 0.972 141.192 31.974 144.771 -0.087 -0.002 0.010
11:DL+WL DW+WL-Z-0.862 -124.048 -27.839 127.137 0.075 0.001 -0.009
12:DL+WLUP+WL-X15.989 139.183 31.181 143.527 -0.084 -0.002 0.010
13:DL+WL DW+WL-X
14.155 -126.057 -28.632 130.041 0.078 0.001 -0.008
52 1:DL -0.040 -6.813 -0.889 6.871 0.011 -0.000 -0.000
2:WL-U 0.301 49.750 6.504 50.174 -0.079 0.000 0.003
3:WL- D -0.192 -31.699 -4.144 31.969 0.050 -0.000 -0.002
4:WL-X 9.477 -0.137 -0.217 9.481 -0.001 -0.002 0.000
5:WL-Z -0.000 0.294 0.154 0.332 -0.001 -0.000 -0.000
6:DL+WL UP 0.262 42.937 5.615 43.303 -0.067 0.000 0.003
7:DL+WLDW -0.232 -38.512 -5.034 38.840 0.061 -0.000 -0.002
8:DL+WL-X 9.438 -6.950 -1.107 11.773 0.010 -0.002 -0.000
9:DL+WL-Z -0.040 -6.519 -0.735 6.560 0.011 -0.000 -0.000
10:DL+WLUP+WL-Z 0.262 43.231 5.769 43.615 -0.068 0.000 0.003
11:DL+WL DW+WL-Z-0.232 -38.218 -4.880 38.529 0.061 -0.000 -0.002
12:DL+WLUP+WL-X 9.739 42.800 5.397 44.224 -0.068 -0.002 0.003

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 23 of 166
Job No Sheet No Rev
24
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
13:DL+WL DW+WL-X9.246 -38.649 -5.251 40.085 0.060 -0.003 -0.002
53 1:DL 0.000 0.426 1.311 1.378 -0.001 -0.000 -0.000
2:WL-U 0.000 -2.703 -9.461 9.839 0.008 0.000 0.000
3:WL- D -0.000 1.723 6.028 6.269 -0.005 -0.000 -0.000
4:WL-X 4.086 0.000 -0.000 4.086 0.000 -0.000 -0.000
5:WL-Z -0.000 -0.047 0.046 0.065 -0.000 0.000 0.000
6:DL+WL UP 0.000 -2.278 -8.150 8.462 0.007 0.000 0.000
7:DL+WLDW -0.000 2.148 7.339 7.647 -0.005 -0.000 -0.000
8:DL+WL-X 4.086 0.426 1.311 4.312 -0.001 -0.000 -0.000
9:DL+WL-Z 0.000 0.379 1.356 1.408 -0.001 -0.000 -0.000
10:DL+WLUP+WL-Z 0.000 -2.325 -8.104 8.431 0.007 0.000 0.000
11:DL+WL DW+WL-Z-0.000 2.101 7.384 7.677 -0.005 -0.000 -0.000
12:DL+WLUP+WL-X 4.086 -2.278 -8.150 9.397 0.007 -0.000 -0.000
13:DL+WL DW+WL-X4.086 2.148 7.339 8.670 -0.005 -0.000 -0.000
54 1:DL -0.000 -1.382 0.822 1.608 0.004 0.000 -0.000
2:WL-U 0.000 10.167 -5.979 11.795 -0.030 -0.000 0.000
3:WL- D -0.000 -6.478 3.810 7.515 0.019 0.000 -0.000
4:WL-X 5.151 0.000 -0.000 5.151 -0.000 -0.002 -0.000
5:WL-Z -0.000 0.024 0.065 0.069 -0.000 -0.000 -0.000
6:DL+WL UP 0.000 8.785 -5.157 10.187 -0.027 -0.000 0.000
7:DL+WLDW -0.000 -7.860 4.632 9.123 0.023 0.000 -0.000
8:DL+WL-X 5.151 -1.382 0.822 5.396 0.004 -0.002 -0.000
9:DL+WL-Z -0.000 -1.358 0.887 1.622 0.004 0.000 -0.000
10:DL+WLUP+WL-Z 0.000 8.808 -5.092 10.174 -0.027 -0.000 0.000
11:DL+WL DW+WL-Z-0.000 -7.836 4.697 9.136 0.023 0.000 -0.000
12:DL+WLUP+WL-X 5.151 8.785 -5.157 11.415 -0.027 -0.002 -0.000
13:DL+WL DW+WL-X5.151 -7.860 4.632 10.477 0.023 -0.002 -0.000
55 1:DL 0.000 -24.205 -5.461 24.814 0.014 -0.000 0.000
2:WL-U -0.000 177.971 40.237 182.463 -0.110 0.000 -0.000
3:WL- D 0.000 -113.397 -25.637 116.259 0.070 -0.000 0.000
4:WL-X 14.982 -0.000 -0.000 14.982 0.000 -0.000 0.000
5:WL-Z -0.000 1.276 0.417 1.343 -0.001 -0.000 -0.000
6:DL+WL UP -0.000 153.765 34.776 157.649 -0.096 0.000 -0.000
7:DL+WLDW 0.000 -137.603 -31.098 141.073 0.085 -0.000 0.000
8:DL+WL-X 14.982 -24.205 -5.461 28.986 0.014 -0.000 0.000
9:DL+WL-Z 0.000 -22.929 -5.044 23.477 0.014 -0.000 0.000
10:DL+WLUP+WL-Z -0.000 155.042 35.192 158.986 -0.097 0.000 -0.000
11:DL+WL DW+WL-Z0.000 -136.326 -30.682 139.736 0.084 -0.000 0.000
12:DL+WLUP+WL-X14.982 153.765 34.776 158.359 -0.096 -0.000 0.000
13:DL+WL DW+WL-X
14.982 -137.603 -31.098 141.866 0.085 -0.000 0.000
56 1:DL -0.000 -7.258 -0.928 7.317 0.012 -0.000 -0.000
2:WL-U -0.000 53.135 6.843 53.574 -0.087 -0.000 0.000
3:WL- D 0.000 -33.856 -4.360 34.136 0.056 0.000 -0.000
4:WL-X 9.466 -0.000 -0.000 9.466 -0.000 -0.002 -0.000
5:WL-Z 0.000 0.294 0.154 0.332 -0.001 0.000 0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 24 of 166
Job No Sheet No Rev
25
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
6:DL+WL UP -0.000 45.877 5.914 46.257 -0.075 -0.000 -0.000
7:DL+WLDW 0.000 -41.114 -5.288 41.452 0.068 0.000 -0.000
8:DL+WL-X 9.466 -7.258 -0.928 11.964 0.012 -0.002 -0.000
9:DL+WL-Z -0.000 -6.964 -0.774 7.007 0.012 -0.000 -0.000
10:DL+WLUP+WL-Z -0.000 46.171 6.068 46.568 -0.076 -0.000 -0.000
11:DL+WL DW+WL-Z0.000 -40.820 -5.134 41.141 0.067 0.000 -0.000
12:DL+WLUP+WL-X 9.466 45.877 5.914 47.216 -0.075 -0.002 -0.000
13:DL+WL DW+WL-X9.466 -41.114 -5.288 42.520 0.068 -0.002 -0.000
57 1:DL -0.005 0.191 1.165 1.181 -0.000 0.000 -0.000
2:WL-U 0.037 -0.959 -8.325 8.380 0.006 -0.000 0.000
3:WL- D -0.023 0.611 5.304 5.339 -0.004 0.000 -0.000
4:WL-X 4.077 -0.166 0.001 4.080 -0.002 0.000 -0.000
5:WL-Z 0.000 -0.047 0.046 0.065 -0.000 0.000 0.000
6:DL+WL UP 0.032 -0.768 -7.160 7.201 0.006 -0.000 0.000
7:DL+WLDW -0.028 0.802 6.469 6.519 -0.004 0.000 -0.000
8:DL+WL-X 4.072 0.025 1.166 4.235 -0.002 0.000 -0.000
9:DL+WL-Z -0.005 0.144 1.211 1.219 -0.000 0.000 -0.000
10:DL+WLUP+WL-Z 0.032 -0.815 -7.114 7.161 0.006 -0.000 0.000
11:DL+WL DW+WL-Z-0.028 0.756 6.515 6.559 -0.004 0.000 -0.000
12:DL+WLUP+WL-X 4.108 -0.934 -7.159 8.307 0.004 -0.000 0.000
13:DL+WL DW+WL-X4.048 0.636 6.470 7.659 -0.006 0.000 -0.000
58 1:DL 0.002 -1.509 0.706 1.666 0.003 0.000 0.000
2:WL-U -0.013 11.125 -5.056 12.220 -0.027 -0.001 -0.000
3:WL- D 0.008 -7.088 3.221 7.786 0.017 0.001 0.000
4:WL-X 5.156 0.095 0.072 5.157 0.001 -0.002 -0.000
5:WL-Z 0.000 0.024 0.065 0.069 -0.000 -0.000 -0.000
6:DL+WL UP -0.012 9.616 -4.350 10.554 -0.024 -0.001 -0.000
7:DL+WLDW 0.010 -8.597 3.927 9.452 0.021 0.001 0.000
8:DL+WL-X 5.158 -1.414 0.777 5.404 0.004 -0.002 -0.000
9:DL+WL-Z 0.002 -1.485 0.770 1.673 0.003 0.000 0.000
10:DL+WLUP+WL-Z -0.012 9.640 -4.286 10.549 -0.024 -0.001 -0.000
11:DL+WL DW+WL-Z0.010 -8.574 3.992 9.457 0.020 0.001 0.000
12:DL+WLUP+WL-X 5.144 9.711 -4.279 11.793 -0.023 -0.003 -0.000
13:DL+WL DW+WL-X5.166 -8.503 3.999 10.723 0.022 -0.001 0.000
59 1:DL 0.148 -22.096 -4.977 22.650 0.013 -0.000 0.001
2:WL-U -1.120 162.012 36.535 166.084 -0.099 0.002 -0.011
3:WL- D 0.714 -103.229 -23.279 105.823 0.063 -0.001 0.007
4:WL-X 15.017 0.733 0.376 15.040 -0.002 -0.000 0.000
5:WL-Z 0.000 1.276 0.417 1.343 -0.001 -0.000 0.000
6:DL+WL UP -0.972 139.916 31.558 143.434 -0.086 0.002 -0.010
7:DL+WLDW 0.862 -125.325 -28.256 128.473 0.076 -0.001 0.009
8:DL+WL-X 15.165 -21.363 -4.601 26.600 0.011 -0.001 0.002
9:DL+WL-Z 0.148 -20.819 -4.560 21.313 0.012 -0.000 0.001
10:DL+WLUP+WL-Z -0.972 141.192 31.974 144.771 -0.087 0.002 -0.010
11:DL+WL DW+WL-Z0.862 -124.048 -27.839 127.137 0.075 -0.001 0.009

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 25 of 166
Job No Sheet No Rev
26
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Node Displacements Cont...


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
12:DL+WLUP+WL-X14.045 140.649 31.934 144.911 -0.088 0.001 -0.009
13:DL+WL DW+WL-X
15.879 -124.592 -27.879 128.657 0.074 -0.002 0.009
60 1:DL 0.040 -6.813 -0.889 6.871 0.011 0.000 0.000
2:WL-U -0.301 49.750 6.504 50.174 -0.079 -0.000 -0.003
3:WL- D 0.192 -31.699 -4.144 31.969 0.050 0.000 0.002
4:WL-X 9.477 0.137 0.217 9.481 0.001 -0.002 0.000
5:WL-Z 0.000 0.294 0.154 0.332 -0.001 0.000 0.000
6:DL+WL UP -0.262 42.937 5.615 43.303 -0.067 -0.000 -0.003
7:DL+WLDW 0.232 -38.512 -5.034 38.840 0.061 0.000 0.002
8:DL+WL-X 9.517 -6.676 -0.672 11.645 0.012 -0.002 0.000
9:DL+WL-Z 0.040 -6.519 -0.735 6.560 0.011 0.000 0.000
10:DL+WLUP+WL-Z -0.262 43.231 5.769 43.615 -0.068 -0.000 -0.003
11:DL+WL DW+WL-Z0.232 -38.218 -4.880 38.529 0.061 0.000 0.002
12:DL+WLUP+WL-X 9.216 43.074 5.832 44.433 -0.066 -0.003 -0.003
13:DL+WL DW+WL-X9.709 -38.375 -4.816 39.876 0.062 -0.002 0.002

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 26 of 166
Job No Sheet No Rev
27
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 1 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 1
STATUS: PASS
SECTION ID: 60CU30X1.6
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.814


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 38.32
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.72
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 11.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 182.48
AREA - EFFECTIVE: 182.48
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.0236E+05
Iy: 1.0236E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.6324E+04
Iye: 1.6324E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.4121E+03
Sze_c - COMPRESSION FIBER: 3.4121E+03
Sye_t - TENSION FIBER: 7.5187E+02
Sye_c - COMPRESSION FIBER: 1.9695E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 27 of 166
Job No Sheet No Rev
28
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 1 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 1
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.277


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 28 of 166
Job No Sheet No Rev
29
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 2 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 2
STATUS: PASS
SECTION ID: 100CU50X2
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.915


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 80.88
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.56
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 25.20
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 385.13
AREA - EFFECTIVE: 385.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 6.1064E+05
Iy: 6.1064E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.6874E+04
Iye: 9.6874E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.2213E+04
Sze_c - COMPRESSION FIBER: 1.2213E+04
Sye_t - TENSION FIBER: 2.6526E+03
Sye_c - COMPRESSION FIBER: 7.1864E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 29 of 166
Job No Sheet No Rev
30
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 2 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 2
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.173


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.99
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 30 of 166
Job No Sheet No Rev
31
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 3 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 3
STATUS: PASS
SECTION ID: 200CU50X4
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.716


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 197.80
BENDING ABOUT Z AXIS: 12.45
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 44.80
SHEAR ALONG Y AXIS: 100.80

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 1140.53
AREA - EFFECTIVE: 1140.53
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.9286E+06
Iy: 5.9286E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.1994E+05
Iye: 2.1994E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 5.9286E+04
Sze_c - COMPRESSION FIBER: 5.9286E+04
Sye_t - TENSION FIBER: 2.1750E+04
Sye_c - COMPRESSION FIBER: 5.5138E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 31 of 166
Job No Sheet No Rev
32
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 3 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 3
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 4.111


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 44.90
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 32 of 166
Job No Sheet No Rev
33
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 4 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 4
STATUS: PASS
SECTION ID: 180CU50X3.15
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.776


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 123.01
BENDING ABOUT Z AXIS: 8.64
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 72.43

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 845.11
AREA - EFFECTIVE: 845.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.7019E+06
Iy: 3.7019E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.7362E+05
Iye: 1.7362E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.1132E+04
Sze_c - COMPRESSION FIBER: 4.1132E+04
Sye_t - TENSION FIBER: 1.6797E+04
Sye_c - COMPRESSION FIBER: 4.3772E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 33 of 166
Job No Sheet No Rev
34
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 4 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 4
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 3.091


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.75
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 34 of 166
Job No Sheet No Rev
35
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 5 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 5
STATUS: PASS
SECTION ID: 90CU50X3.15
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.989


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 77.37
BENDING ABOUT Z AXIS: 3.33
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 32.74

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 561.61
AREA - EFFECTIVE: 561.61
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 7.1370E+05
Iy: 7.1370E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.4087E+05
Iye: 1.4087E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5860E+04
Sze_c - COMPRESSION FIBER: 1.5860E+04
Sye_t - TENSION FIBER: 9.5445E+03
Sye_c - COMPRESSION FIBER: 3.9973E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 35 of 166
Job No Sheet No Rev
36
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 5 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 5
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.527


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.46
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 36 of 166
Job No Sheet No Rev
37
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 6 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 6
STATUS: PASS
SECTION ID: 100CU40X1.6
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.881


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 24.65
BENDING ABOUT Z AXIS: 1.74
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.13
SHEAR ALONG Y AXIS: 19.12

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 278.48
AREA - EFFECTIVE: 278.48
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.1990E+05
Iy: 4.1990E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.2503E+04
Iye: 4.2503E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 8.3980E+03
Sze_c - COMPRESSION FIBER: 8.3980E+03
Sye_t - TENSION FIBER: 4.4104E+03
Sye_c - COMPRESSION FIBER: 1.3998E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 37 of 166
Job No Sheet No Rev
38
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 6 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 6
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.712


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 41.85
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 38 of 166
Job No Sheet No Rev
39
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 7 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 7
STATUS: PASS
SECTION ID: 150CS50X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 992.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.876


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 176.34
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.41
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 30.20
SHEAR ALONG Y AXIS: 59.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 839.71
AREA - EFFECTIVE: 839.71
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.7160E+06
Iy: 2.7160E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.7276E+05
Iye: 2.7276E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.6214E+04
Sze_c - COMPRESSION FIBER: 3.6214E+04
Sye_t - TENSION FIBER: 7.8682E+03
Sye_c - COMPRESSION FIBER: 1.7788E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 39 of 166
Job No Sheet No Rev
40
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 7 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 7
STATUS: PASS
SECTION ID: 140CS60X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 992.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.834


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 182.95
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.79
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 39.02
SHEAR ALONG Y AXIS: 54.79

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 871.21
AREA - EFFECTIVE: 871.21
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.5959E+06
Iy: 2.5959E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.1703E+05
Iye: 4.1703E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7085E+04
Sze_c - COMPRESSION FIBER: 3.7085E+04
Sye_t - TENSION FIBER: 1.0354E+04
Sye_c - COMPRESSION FIBER: 2.1145E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 40 of 166
Job No Sheet No Rev
41
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 8 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 8
STATUS: PASS
SECTION ID: 30LU30X1.6
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.742


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 4.12

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 91.24
AREA - EFFECTIVE: 91.24
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.3276E+04
Iy: 1.3276E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 3.0502E+03
Iye: 3.0502E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 6.7886E+02
Sze_c - COMPRESSION FIBER: 5.8050E+02
Sye_t - TENSION FIBER: 2.8713E+02
Sye_c - COMPRESSION FIBER: 3.0306E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 41 of 166
Job No Sheet No Rev
42
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 8 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 8
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.587


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.5666E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.7421E+02
Sze_c - COMPRESSION FIBER: 1.5044E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 42 of 166
Job No Sheet No Rev
43
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 9 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 9
STATUS: PASS
SECTION ID: 40LU40X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.908


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 6.93

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 152.57
AREA - EFFECTIVE: 152.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.9540E+04
Iy: 4.0194E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.1412E+03
Iye: 9.1412E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5334E+03
Sze_c - COMPRESSION FIBER: 1.3241E+03
Sye_t - TENSION FIBER: 6.4536E+02
Sye_c - COMPRESSION FIBER: 6.7900E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 43 of 166
Job No Sheet No Rev
44
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 9 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 9
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 4.364


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.8778E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.8609E+02
Sze_c - COMPRESSION FIBER: 1.6069E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 44 of 166
Job No Sheet No Rev
45
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 10 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 10
STATUS: PASS
SECTION ID: 70CU30X1.6
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.895


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 41.68
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.88
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 13.89

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 198.48
AREA - EFFECTIVE: 198.48
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.4669E+05
Iy: 1.4669E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.7149E+04
Iye: 1.7149E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.1911E+03
Sze_c - COMPRESSION FIBER: 4.1911E+03
Sye_t - TENSION FIBER: 7.6850E+02
Sye_c - COMPRESSION FIBER: 2.2316E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 45 of 166
Job No Sheet No Rev
46
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 10 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 10
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.374


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 46 of 166
Job No Sheet No Rev
47
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 11 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 11
STATUS: PASS
SECTION ID: 90CU50X3.15
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.949


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 117.94
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 3.33
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 32.74

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 561.61
AREA - EFFECTIVE: 561.61
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 7.1370E+05
Iy: 7.1370E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.4087E+05
Iye: 1.4087E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5860E+04
Sze_c - COMPRESSION FIBER: 1.5860E+04
Sye_t - TENSION FIBER: 3.9973E+03
Sye_c - COMPRESSION FIBER: 9.5445E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 47 of 166
Job No Sheet No Rev
48
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 11 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 11
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.581


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.99
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 48 of 166
Job No Sheet No Rev
49
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 12 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 12
STATUS: PASS
SECTION ID: 200CU50X4
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.890


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 197.80
BENDING ABOUT Z AXIS: 12.45
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 44.80
SHEAR ALONG Y AXIS: 100.80

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 1140.53
AREA - EFFECTIVE: 1140.53
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.9286E+06
Iy: 5.9286E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.1994E+05
Iye: 2.1994E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 5.9286E+04
Sze_c - COMPRESSION FIBER: 5.9286E+04
Sye_t - TENSION FIBER: 2.1750E+04
Sye_c - COMPRESSION FIBER: 5.5138E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 49 of 166
Job No Sheet No Rev
50
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 12 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 12
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 5.108


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 44.90
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 50 of 166
Job No Sheet No Rev
51
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 13 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 13
STATUS: PASS
SECTION ID: 180CU50X3.15
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.954


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 123.01
BENDING ABOUT Z AXIS: 8.64
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 72.43

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 845.11
AREA - EFFECTIVE: 845.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.7019E+06
Iy: 3.7019E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.7362E+05
Iye: 1.7362E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.1132E+04
Sze_c - COMPRESSION FIBER: 4.1132E+04
Sye_t - TENSION FIBER: 1.6797E+04
Sye_c - COMPRESSION FIBER: 4.3772E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 51 of 166
Job No Sheet No Rev
52
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 13 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 13
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 3.801


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.75
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 52 of 166
Job No Sheet No Rev
53
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 14 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 14
STATUS: PASS
SECTION ID: 100CU60X3.15
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.893


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 82.93
BENDING ABOUT Z AXIS: 4.45
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 45.97
SHEAR ALONG Y AXIS: 37.15

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 656.11
AREA - EFFECTIVE: 656.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.0601E+06
Iy: 1.0601E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.4202E+05
Iye: 2.4202E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1202E+04
Sze_c - COMPRESSION FIBER: 2.1202E+04
Sye_t - TENSION FIBER: 1.3453E+04
Sye_c - COMPRESSION FIBER: 5.7611E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 53 of 166
Job No Sheet No Rev
54
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 14 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 14
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.840


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.46
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 54 of 166
Job No Sheet No Rev
55
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 15 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 15
STATUS: PASS
SECTION ID: 90CU40X2
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.986


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 39.08
BENDING ABOUT Z AXIS: 1.87
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 325.13
AREA - EFFECTIVE: 325.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.0198E+05
Iy: 4.0198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.0546E+04
Iye: 5.0546E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 8.9329E+03
Sze_c - COMPRESSION FIBER: 8.9329E+03
Sye_t - TENSION FIBER: 4.8743E+03
Sye_c - COMPRESSION FIBER: 1.7059E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 55 of 166
Job No Sheet No Rev
56
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 15 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 15
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.858


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 41.85
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 56 of 166
Job No Sheet No Rev
57
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 16 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 16
STATUS: PASS
SECTION ID: 140CS60X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.998


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 182.95
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.79
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 39.02
SHEAR ALONG Y AXIS: 54.79

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 871.21
AREA - EFFECTIVE: 871.21
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.5959E+06
Iy: 2.5959E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.1703E+05
Iye: 4.1703E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7085E+04
Sze_c - COMPRESSION FIBER: 3.7085E+04
Sye_t - TENSION FIBER: 1.0354E+04
Sye_c - COMPRESSION FIBER: 2.1145E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 57 of 166
Job No Sheet No Rev
58
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 16 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 16
STATUS: PASS
SECTION ID: 140CS60X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.998


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 182.95
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.79
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 39.02
SHEAR ALONG Y AXIS: 54.79

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 871.21
AREA - EFFECTIVE: 871.21
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.5959E+06
Iy: 2.5959E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.1703E+05
Iye: 4.1703E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7085E+04
Sze_c - COMPRESSION FIBER: 3.7085E+04
Sye_t - TENSION FIBER: 1.0354E+04
Sye_c - COMPRESSION FIBER: 2.1145E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 58 of 166
Job No Sheet No Rev
59
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 17 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 17
STATUS: PASS
SECTION ID: 30LU30X1.6
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.742


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 4.12

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 91.24
AREA - EFFECTIVE: 91.24
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.3276E+04
Iy: 1.3276E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 3.0502E+03
Iye: 3.0502E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 6.7886E+02
Sze_c - COMPRESSION FIBER: 5.8050E+02
Sye_t - TENSION FIBER: 2.8713E+02
Sye_c - COMPRESSION FIBER: 3.0306E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 59 of 166
Job No Sheet No Rev
60
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 17 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 17
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.587


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.5666E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.7421E+02
Sze_c - COMPRESSION FIBER: 1.5044E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 60 of 166
Job No Sheet No Rev
61
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 18 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 18
STATUS: PASS
SECTION ID: 40LU40X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.908


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 6.93

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 152.57
AREA - EFFECTIVE: 152.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.9540E+04
Iy: 4.0194E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.1412E+03
Iye: 9.1412E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5334E+03
Sze_c - COMPRESSION FIBER: 1.3241E+03
Sye_t - TENSION FIBER: 6.4536E+02
Sye_c - COMPRESSION FIBER: 6.7900E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 61 of 166
Job No Sheet No Rev
62
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 18 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 18
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 4.364


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.8778E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.8609E+02
Sze_c - COMPRESSION FIBER: 1.6069E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 62 of 166
Job No Sheet No Rev
63
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 19 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 19
STATUS: PASS
SECTION ID: 70CU30X1.6
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.895


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 41.68
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.88
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 13.89

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 198.48
AREA - EFFECTIVE: 198.48
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.4669E+05
Iy: 1.4669E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.7149E+04
Iye: 1.7149E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.1911E+03
Sze_c - COMPRESSION FIBER: 4.1911E+03
Sye_t - TENSION FIBER: 7.6850E+02
Sye_c - COMPRESSION FIBER: 2.2316E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 63 of 166
Job No Sheet No Rev
64
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 19 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 19
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.374


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 64 of 166
Job No Sheet No Rev
65
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 20 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 20
STATUS: PASS
SECTION ID: 100CU40X3.15
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.987


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 111.32
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 3.19
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 28.33
SHEAR ALONG Y AXIS: 37.15

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 530.11
AREA - EFFECTIVE: 530.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 7.6461E+05
Iy: 7.6461E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 7.8056E+04
Iye: 7.8056E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5292E+04
Sze_c - COMPRESSION FIBER: 1.5292E+04
Sye_t - TENSION FIBER: 2.6354E+03
Sye_c - COMPRESSION FIBER: 7.5186E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 65 of 166
Job No Sheet No Rev
66
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 20 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 20
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.461


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 66 of 166
Job No Sheet No Rev
67
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 21 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 21
STATUS: PASS
SECTION ID: 200CU50X4
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.890


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 197.80
BENDING ABOUT Z AXIS: 12.45
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 44.80
SHEAR ALONG Y AXIS: 100.80

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 1140.53
AREA - EFFECTIVE: 1140.53
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.9286E+06
Iy: 5.9286E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.1994E+05
Iye: 2.1994E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 5.9286E+04
Sze_c - COMPRESSION FIBER: 5.9286E+04
Sye_t - TENSION FIBER: 2.1750E+04
Sye_c - COMPRESSION FIBER: 5.5138E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 67 of 166
Job No Sheet No Rev
68
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 21 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 21
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 5.108


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 44.90
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 68 of 166
Job No Sheet No Rev
69
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 22 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 22
STATUS: PASS
SECTION ID: 180CU50X3.15
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.956


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 123.01
BENDING ABOUT Z AXIS: 8.50
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 72.43

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 845.11
AREA - EFFECTIVE: 845.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.7019E+06
Iy: 3.7019E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.7362E+05
Iye: 1.7362E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.1132E+04
Sze_c - COMPRESSION FIBER: 4.1132E+04
Sye_t - TENSION FIBER: 1.6797E+04
Sye_c - COMPRESSION FIBER: 4.3772E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 69 of 166
Job No Sheet No Rev
70
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 22 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 22
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 3.943


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.75
BENDING ABOUT Z AXIS: 2.06
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 70 of 166
Job No Sheet No Rev
71
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 23 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 23
STATUS: PASS
SECTION ID: 100CU60X3.15
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.893


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 82.93
BENDING ABOUT Z AXIS: 4.45
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 45.97
SHEAR ALONG Y AXIS: 37.15

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 656.11
AREA - EFFECTIVE: 656.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.0601E+06
Iy: 1.0601E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.4202E+05
Iye: 2.4202E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1202E+04
Sze_c - COMPRESSION FIBER: 2.1202E+04
Sye_t - TENSION FIBER: 1.3453E+04
Sye_c - COMPRESSION FIBER: 5.7611E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 71 of 166
Job No Sheet No Rev
72
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 23 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 23
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.928


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.46
BENDING ABOUT Z AXIS: 2.04
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 72 of 166
Job No Sheet No Rev
73
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 24 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 24
STATUS: PASS
SECTION ID: 90CU40X2
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.986


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 39.08
BENDING ABOUT Z AXIS: 1.88
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 325.13
AREA - EFFECTIVE: 325.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.0198E+05
Iy: 4.0198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.0546E+04
Iye: 5.0546E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 8.9329E+03
Sze_c - COMPRESSION FIBER: 8.9329E+03
Sye_t - TENSION FIBER: 4.8743E+03
Sye_c - COMPRESSION FIBER: 1.7059E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 73 of 166
Job No Sheet No Rev
74
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 24 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 24
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.858


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 41.85
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 74 of 166
Job No Sheet No Rev
75
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 25 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 25
STATUS: PASS
SECTION ID: 140CS60X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.998


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 182.95
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.79
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 39.02
SHEAR ALONG Y AXIS: 54.79

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 871.21
AREA - EFFECTIVE: 871.21
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.5959E+06
Iy: 2.5959E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.1703E+05
Iye: 4.1703E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7085E+04
Sze_c - COMPRESSION FIBER: 3.7085E+04
Sye_t - TENSION FIBER: 1.0354E+04
Sye_c - COMPRESSION FIBER: 2.1145E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 75 of 166
Job No Sheet No Rev
76
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 25 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 25
STATUS: PASS
SECTION ID: 140CS60X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.998


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 182.95
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.79
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 39.02
SHEAR ALONG Y AXIS: 54.79

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 871.21
AREA - EFFECTIVE: 871.21
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.5959E+06
Iy: 2.5959E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.1703E+05
Iye: 4.1703E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7085E+04
Sze_c - COMPRESSION FIBER: 3.7085E+04
Sye_t - TENSION FIBER: 1.0354E+04
Sye_c - COMPRESSION FIBER: 2.1145E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 76 of 166
Job No Sheet No Rev
77
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 26 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 26
STATUS: PASS
SECTION ID: 30LU30X1.6
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.742


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 4.12

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 91.24
AREA - EFFECTIVE: 91.24
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.3276E+04
Iy: 1.3276E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 3.0502E+03
Iye: 3.0502E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 6.7886E+02
Sze_c - COMPRESSION FIBER: 5.8050E+02
Sye_t - TENSION FIBER: 2.8713E+02
Sye_c - COMPRESSION FIBER: 3.0306E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 77 of 166
Job No Sheet No Rev
78
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 26 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 26
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.587


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.5666E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.7421E+02
Sze_c - COMPRESSION FIBER: 1.5044E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 78 of 166
Job No Sheet No Rev
79
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 27 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 27
STATUS: PASS
SECTION ID: 40LU40X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.908


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 6.93

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 152.57
AREA - EFFECTIVE: 152.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.9540E+04
Iy: 4.0194E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.1412E+03
Iye: 9.1412E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5334E+03
Sze_c - COMPRESSION FIBER: 1.3241E+03
Sye_t - TENSION FIBER: 6.4536E+02
Sye_c - COMPRESSION FIBER: 6.7900E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 79 of 166
Job No Sheet No Rev
80
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 27 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 27
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 4.364


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.8778E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.8609E+02
Sze_c - COMPRESSION FIBER: 1.6069E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 80 of 166
Job No Sheet No Rev
81
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 28 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 28
STATUS: PASS
SECTION ID: 60CU30X1.6
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.814


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 38.32
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.72
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 11.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 182.48
AREA - EFFECTIVE: 182.48
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.0236E+05
Iy: 1.0236E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.6324E+04
Iye: 1.6324E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.4121E+03
Sze_c - COMPRESSION FIBER: 3.4121E+03
Sye_t - TENSION FIBER: 7.5187E+02
Sye_c - COMPRESSION FIBER: 1.9695E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 81 of 166
Job No Sheet No Rev
82
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 28 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 28
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 240.93
CRITICAL LOCATION: 240.93

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.277


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 82 of 166
Job No Sheet No Rev
83
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 29 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 29
STATUS: PASS
SECTION ID: 100CU50X2
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.915


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 80.88
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.56
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 25.20
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 385.13
AREA - EFFECTIVE: 385.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 6.1064E+05
Iy: 6.1064E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.6874E+04
Iye: 9.6874E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.2213E+04
Sze_c - COMPRESSION FIBER: 1.2213E+04
Sye_t - TENSION FIBER: 2.6526E+03
Sye_c - COMPRESSION FIBER: 7.1864E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 83 of 166
Job No Sheet No Rev
84
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 29 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 29
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 749.03
CRITICAL LOCATION: 749.03

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.084


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 72.48
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 1.7300E+03
Sye_c - COMPRESSION FIBER: 5.3120E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 84 of 166
Job No Sheet No Rev
85
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 30 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 30
STATUS: PASS
SECTION ID: 200CU50X4
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.716


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 197.80
BENDING ABOUT Z AXIS: 12.45
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 44.80
SHEAR ALONG Y AXIS: 100.80

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 1140.53
AREA - EFFECTIVE: 1140.53
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.9286E+06
Iy: 5.9286E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.1994E+05
Iye: 2.1994E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 5.9286E+04
Sze_c - COMPRESSION FIBER: 5.9286E+04
Sye_t - TENSION FIBER: 2.1750E+04
Sye_c - COMPRESSION FIBER: 5.5138E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 85 of 166
Job No Sheet No Rev
86
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 30 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 30
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 299.87
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 4.111


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 44.90
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 86 of 166
Job No Sheet No Rev
87
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 31 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 31
STATUS: PASS
SECTION ID: 180CU50X3.15
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.778


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 123.01
BENDING ABOUT Z AXIS: 8.50
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 72.43

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 845.11
AREA - EFFECTIVE: 845.11
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.7019E+06
Iy: 3.7019E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.7362E+05
Iye: 1.7362E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.1132E+04
Sze_c - COMPRESSION FIBER: 4.1132E+04
Sye_t - TENSION FIBER: 1.6797E+04
Sye_c - COMPRESSION FIBER: 4.3772E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 87 of 166
Job No Sheet No Rev
88
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 31 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 31
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 680.17
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 3.206


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.75
BENDING ABOUT Z AXIS: 2.06
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 88 of 166
Job No Sheet No Rev
89
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 32 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 32
STATUS: PASS
SECTION ID: 90CU50X3.15
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.989


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 77.37
BENDING ABOUT Z AXIS: 3.33
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 37.15
SHEAR ALONG Y AXIS: 32.74

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 561.61
AREA - EFFECTIVE: 561.61
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 7.1370E+05
Iy: 7.1370E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.4087E+05
Iye: 1.4087E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5860E+04
Sze_c - COMPRESSION FIBER: 1.5860E+04
Sye_t - TENSION FIBER: 9.5445E+03
Sye_c - COMPRESSION FIBER: 3.9973E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 89 of 166
Job No Sheet No Rev
90
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 32 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 32
STATUS: FAIL
SECTION ID: 100CU40X2
MEMBER LENGTH: 700.78
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.600


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 40.46
BENDING ABOUT Z AXIS: 2.04
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 90 of 166
Job No Sheet No Rev
91
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 33 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 33
STATUS: PASS
SECTION ID: 100CU40X1.6
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.881


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 24.65
BENDING ABOUT Z AXIS: 1.76
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.13
SHEAR ALONG Y AXIS: 19.12

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 278.48
AREA - EFFECTIVE: 278.48
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.1990E+05
Iy: 4.1990E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.2503E+04
Iye: 4.2503E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 8.3980E+03
Sze_c - COMPRESSION FIBER: 8.3980E+03
Sye_t - TENSION FIBER: 4.4104E+03
Sye_c - COMPRESSION FIBER: 1.3998E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 91 of 166
Job No Sheet No Rev
92
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 33 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 33
STATUS: PASS
SECTION ID: 100CU40X2
MEMBER LENGTH: 599.39
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.712


GOVERNING MODE: Bend + Compress
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 41.85
BENDING ABOUT Z AXIS: 2.16
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 25.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 345.13
AREA - EFFECTIVE: 345.13
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.1460E+05
Iy: 5.1460E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 5.2201E+04
Iye: 5.2201E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0292E+04
Sze_c - COMPRESSION FIBER: 1.0292E+04
Sye_t - TENSION FIBER: 5.3120E+03
Sye_c - COMPRESSION FIBER: 1.7300E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 92 of 166
Job No Sheet No Rev
93
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 34 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 34
STATUS: PASS
SECTION ID: 150CS50X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.871


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 176.34
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.41
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 30.20
SHEAR ALONG Y AXIS: 59.20

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 839.71
AREA - EFFECTIVE: 839.71
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.7160E+06
Iy: 2.7160E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 2.7276E+05
Iye: 2.7276E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.6214E+04
Sze_c - COMPRESSION FIBER: 3.6214E+04
Sye_t - TENSION FIBER: 7.8682E+03
Sye_c - COMPRESSION FIBER: 1.7788E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 93 of 166
Job No Sheet No Rev
94
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 34 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 34
STATUS: PASS
SECTION ID: 140CS60X3.15
MEMBER LENGTH: 992.00
CRITICAL LOCATION: 992.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.834


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 182.95
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 7.79
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 39.02
SHEAR ALONG Y AXIS: 54.79

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 871.21
AREA - EFFECTIVE: 871.21
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 2.5959E+06
Iy: 2.5959E+06
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.1703E+05
Iye: 4.1703E+05
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7085E+04
Sze_c - COMPRESSION FIBER: 3.7085E+04
Sye_t - TENSION FIBER: 1.0354E+04
Sye_c - COMPRESSION FIBER: 2.1145E+04

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 94 of 166
Job No Sheet No Rev
95
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 35 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 35
STATUS: PASS
SECTION ID: 30LU30X1.6
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.742


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.65
SHEAR ALONG Y AXIS: 4.12

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 91.24
AREA - EFFECTIVE: 91.24
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.3276E+04
Iy: 1.3276E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 3.0502E+03
Iye: 3.0502E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 6.7886E+02
Sze_c - COMPRESSION FIBER: 5.8050E+02
Sye_t - TENSION FIBER: 2.8713E+02
Sye_c - COMPRESSION FIBER: 3.0306E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 95 of 166
Job No Sheet No Rev
96
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 35 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 35
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 996.01
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 1.587


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.5666E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.7421E+02
Sze_c - COMPRESSION FIBER: 1.5044E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 96 of 166
Job No Sheet No Rev
97
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 36 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 36
STATUS: PASS
SECTION ID: 40LU40X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.908


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 19.60
SHEAR ALONG Y AXIS: 6.93

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 152.57
AREA - EFFECTIVE: 152.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 3.9540E+04
Iy: 4.0194E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.1412E+03
Iye: 9.1412E+03
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.5334E+03
Sze_c - COMPRESSION FIBER: 1.3241E+03
Sye_t - TENSION FIBER: 6.4536E+02
Sye_c - COMPRESSION FIBER: 6.7900E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 97 of 166
Job No Sheet No Rev
98
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 36 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 36
STATUS: FAIL
SECTION ID: 40LU20X2
MEMBER LENGTH: 1651.41
CRITICAL LOCATION: 1651.41

GOVERNING LOAD-TO-RESISTANCE RATIO: 4.364


GOVERNING MODE: Bend Y + Shear
GOVERNING LOAD/COMBINATION NUMBER: 4

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.00
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 8.40
SHEAR ALONG Y AXIS: 2.97

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 72.57
AREA - EFFECTIVE: 72.57
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5666E+03
Iy: 4.8778E+03
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 9.4791E+02
Iye: 9.4791E+02
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.8609E+02
Sze_c - COMPRESSION FIBER: 1.6069E+02
Sye_t - TENSION FIBER: 1.3421E+02
Sye_c - COMPRESSION FIBER: 1.4760E+02

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 98 of 166
Job No Sheet No Rev
99
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 37 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 37
STATUS: PASS
SECTION ID: 50CS40X1.25
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1050.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.993


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 36.93
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.47
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.81
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 175.87
AREA - EFFECTIVE: 175.87
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 7.5589E+04
Iy: 7.5589E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 3.8689E+04
Iye: 3.8689E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.0236E+03
Sze_c - COMPRESSION FIBER: 3.0236E+03
Sye_t - TENSION FIBER: 1.6033E+03
Sye_c - COMPRESSION FIBER: 2.4381E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 99 of 166
Job No Sheet No Rev
100
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 37 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 37
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1050.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.295


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 100 of 166
Job No Sheet No Rev
101
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 38 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 38
STATUS: PASS
SECTION ID: 50CS40X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1283.33

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.867


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 46.40
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 14.34
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 220.97
AREA - EFFECTIVE: 220.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 9.3240E+04
Iy: 9.3240E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.7240E+04
Iye: 4.7240E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7296E+03
Sze_c - COMPRESSION FIBER: 3.7296E+03
Sye_t - TENSION FIBER: 2.9844E+03
Sye_c - COMPRESSION FIBER: 1.9544E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 101 of 166
Job No Sheet No Rev
102
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 38 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 38
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1283.33

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.318


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 102 of 166
Job No Sheet No Rev
103
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 39 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 39
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.879


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 4.0239E+03
Sye_c - COMPRESSION FIBER: 2.7751E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 103 of 166
Job No Sheet No Rev
104
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 39 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 39
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.451


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 104 of 166
Job No Sheet No Rev
105
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 40 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 40
STATUS: PASS
SECTION ID: 50CS40X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1283.33

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.966


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 21.92
BENDING ABOUT Z AXIS: 0.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 14.34
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 220.97
AREA - EFFECTIVE: 220.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 9.3240E+04
Iy: 9.3240E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.7240E+04
Iye: 4.7240E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7296E+03
Sze_c - COMPRESSION FIBER: 3.7296E+03
Sye_t - TENSION FIBER: 2.9844E+03
Sye_c - COMPRESSION FIBER: 1.9544E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 105 of 166
Job No Sheet No Rev
106
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 40 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 40
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1283.33

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.355


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 106 of 166
Job No Sheet No Rev
107
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 41 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 41
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.984


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 107 of 166
Job No Sheet No Rev
108
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 41 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 41
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.505


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 108 of 166
Job No Sheet No Rev
109
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 42 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 42
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.891


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.87
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 4.0239E+03
Sye_c - COMPRESSION FIBER: 2.7751E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 109 of 166
Job No Sheet No Rev
110
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 42 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 42
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.401


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.93
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 110 of 166
Job No Sheet No Rev
111
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 43 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 43
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.929


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 4.0239E+03
Sye_c - COMPRESSION FIBER: 2.7751E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 111 of 166
Job No Sheet No Rev
112
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 43 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 43
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.477


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 112 of 166
Job No Sheet No Rev
113
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 44 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 44
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.825


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 113 of 166
Job No Sheet No Rev
114
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 44 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 44
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.424


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 114 of 166
Job No Sheet No Rev
115
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 45 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 45
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.981


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 115 of 166
Job No Sheet No Rev
116
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 45 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 45
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.504


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 116 of 166
Job No Sheet No Rev
117
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 46 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 46
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.889


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.87
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 4.0239E+03
Sye_c - COMPRESSION FIBER: 2.7751E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 117 of 166
Job No Sheet No Rev
118
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 46 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 46
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.400


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.93
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 118 of 166
Job No Sheet No Rev
119
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 47 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 47
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.878


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 4.0239E+03
Sye_c - COMPRESSION FIBER: 2.7751E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 119 of 166
Job No Sheet No Rev
120
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 47 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 47
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.451


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 120 of 166
Job No Sheet No Rev
121
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 48 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 48
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.769


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.87
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 121 of 166
Job No Sheet No Rev
122
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 48 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 48
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.354


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 122 of 166
Job No Sheet No Rev
123
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 49 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 49
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 123 of 166
Job No Sheet No Rev
124
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 49 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 49
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 124 of 166
Job No Sheet No Rev
125
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 50 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 50
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 125 of 166
Job No Sheet No Rev
126
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 50 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 50
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 126 of 166
Job No Sheet No Rev
127
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 51 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 51
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 127 of 166
Job No Sheet No Rev
128
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 51 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 51
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 128 of 166
Job No Sheet No Rev
129
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 52 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 52
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 129 of 166
Job No Sheet No Rev
130
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 52 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 52
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 130 of 166
Job No Sheet No Rev
131
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 53 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 53
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 131 of 166
Job No Sheet No Rev
132
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 53 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 53
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 132 of 166
Job No Sheet No Rev
133
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 54 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 54
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 133 of 166
Job No Sheet No Rev
134
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 54 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 54
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 134 of 166
Job No Sheet No Rev
135
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 55 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 55
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 135 of 166
Job No Sheet No Rev
136
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 55 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 55
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 136 of 166
Job No Sheet No Rev
137
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 56 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 56
STATUS: PASS
SECTION ID: 50CS25X1.25
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.996


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.43
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 6.56
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 138.37
AREA - EFFECTIVE: 138.37
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 5.3309E+04
Iy: 5.3309E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 1.2447E+04
Iye: 1.2447E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 2.1324E+03
Sze_c - COMPRESSION FIBER: 2.1324E+03
Sye_t - TENSION FIBER: 7.9188E+02
Sye_c - COMPRESSION FIBER: 1.3410E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 137 of 166
Job No Sheet No Rev
138
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 56 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 56
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 875.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.207


GOVERNING MODE: Bend Z + Shear
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 2.14
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 138 of 166
Job No Sheet No Rev
139
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 57 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 57
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.981


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 139 of 166
Job No Sheet No Rev
140
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 57 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 57
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.504


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 140 of 166
Job No Sheet No Rev
141
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 58 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 58
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.889


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.87
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 141 of 166
Job No Sheet No Rev
142
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 58 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 58
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.449


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 12

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 142 of 166
Job No Sheet No Rev
143
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 59 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 59
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.878


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 143 of 166
Job No Sheet No Rev
144
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 59 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 59
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.451


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 144 of 166
Job No Sheet No Rev
145
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 60 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 60
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.779


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 12

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 145 of 166
Job No Sheet No Rev
146
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 60 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 60
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.400


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 12

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 146 of 166
Job No Sheet No Rev
147
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 63 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 63
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.984


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 147 of 166
Job No Sheet No Rev
148
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 63 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 63
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.505


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 148 of 166
Job No Sheet No Rev
149
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 64 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 64
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.891


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 53.12
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.87
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 149 of 166
Job No Sheet No Rev
150
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 64 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 64
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.457


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 12

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 150 of 166
Job No Sheet No Rev
151
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 65 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 65
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.929


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 151 of 166
Job No Sheet No Rev
152
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 65 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 65
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.477


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 152 of 166
Job No Sheet No Rev
153
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 66 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 66
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.825


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 153 of 166
Job No Sheet No Rev
154
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 66 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 66
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 1400.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.424


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 154 of 166
Job No Sheet No Rev
155
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 69 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 69
STATUS: PASS
SECTION ID: 50CS40X1.25
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 350.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.993


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 36.93
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.47
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 11.81
SHEAR ALONG Y AXIS: 7.65

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 175.87
AREA - EFFECTIVE: 175.87
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 7.5589E+04
Iy: 7.5589E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 3.8689E+04
Iye: 3.8689E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.0236E+03
Sze_c - COMPRESSION FIBER: 3.0236E+03
Sye_t - TENSION FIBER: 2.4381E+03
Sye_c - COMPRESSION FIBER: 1.6033E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 155 of 166
Job No Sheet No Rev
156
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 69 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 69
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 350.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.295


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 5.9753E+03
Sye_c - COMPRESSION FIBER: 3.1620E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 156 of 166
Job No Sheet No Rev
157
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 70 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 70
STATUS: PASS
SECTION ID: 50CS40X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 116.67

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.867


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 46.40
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 0.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 14.34
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 220.97
AREA - EFFECTIVE: 220.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 9.3240E+04
Iy: 9.3240E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.7240E+04
Iye: 4.7240E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7296E+03
Sze_c - COMPRESSION FIBER: 3.7296E+03
Sye_t - TENSION FIBER: 1.9544E+03
Sye_c - COMPRESSION FIBER: 2.9844E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 157 of 166
Job No Sheet No Rev
158
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 70 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 70
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 116.67

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.318


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 77.76
AXIAL COMPRESSION: 0.00
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 158 of 166
Job No Sheet No Rev
159
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 71 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 71
STATUS: PASS
SECTION ID: 50CS50X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.879


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 17.12
BENDING ABOUT Z AXIS: 0.81
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 18.82
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 252.97
AREA - EFFECTIVE: 252.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 1.1198E+05
Iy: 1.1198E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2120E+04
Iye: 8.2120E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 4.4792E+03
Sze_c - COMPRESSION FIBER: 4.4792E+03
Sye_t - TENSION FIBER: 2.7751E+03
Sye_c - COMPRESSION FIBER: 4.0239E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 159 of 166
Job No Sheet No Rev
160
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 71 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 71
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 0.00

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.451


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 160 of 166
Job No Sheet No Rev
161
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 72 Select 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 72
STATUS: PASS
SECTION ID: 50CS40X1.6
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 116.67

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.966


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 21.92
BENDING ABOUT Z AXIS: 0.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 14.34
SHEAR ALONG Y AXIS: 9.41

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 220.97
AREA - EFFECTIVE: 220.97
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 9.3240E+04
Iy: 9.3240E+04
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 4.7240E+04
Iye: 4.7240E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 3.7296E+03
Sze_c - COMPRESSION FIBER: 3.7296E+03
Sye_t - TENSION FIBER: 1.9544E+03
Sye_c - COMPRESSION FIBER: 2.9844E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 161 of 166
Job No Sheet No Rev
162
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Steel Design (Track 2) Beam 72 Check 1


UNITS ARE: MM, KN, KNM, MPA

MEMBER NUMBER: 72
STATUS: PASS
SECTION ID: 90CS40X2
MEMBER LENGTH: 1400.00
CRITICAL LOCATION: 116.67

GOVERNING LOAD-TO-RESISTANCE RATIO: 0.355


GOVERNING MODE: Bending Z
GOVERNING LOAD/COMBINATION NUMBER: 2

MEMBER RESISTANCES (ZERO INDICATES THAT NO


CORRESPONDING LOAD IS PRESENT):
AXIAL TENSION: 0.00
AXIAL COMPRESSION: 46.93
BENDING ABOUT Z AXIS: 1.58
BENDING ABOUT Y AXIS: 0.00
SHEAR ALONG Z AXIS: 16.80
SHEAR ALONG Y AXIS: 22.40

YIELD STRENGTH - VIRGIN STEEL: 350.00


YIELD STRENGTH - COLD WORK OF FORMING: 350.00
TENSILE STRENGTH: 450.00

CROSS-SECTIONAL PROPERTIES:
AREA - FULL UNREDUCED: 370.27
AREA - EFFECTIVE: 370.27
MOMENT OF INERTIA - FULL UNREDUCED SECTION:
Iz: 4.5813E+05
Iy: 4.5813E+05
MOMENT OF INERTIA - EFFECTIVE SECTION:
Ize: 8.2711E+04
Iye: 8.2711E+04
ELASTIC SECTION MODULUS - EFFECTIVE SECTION:
Sze_t - TENSION FIBER: 1.0181E+04
Sze_c - COMPRESSION FIBER: 1.0181E+04
Sye_t - TENSION FIBER: 3.1620E+03
Sye_c - COMPRESSION FIBER: 5.9753E+03

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 162 of 166
Job No Sheet No Rev
163
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Reactions
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
1 1:DL 0.010 1.460 -0.005 -0.900 0.000 -0.010
2:WL-U -0.063 -9.989 0.040 6.493 -0.000 0.061
3:WL- D 0.040 6.365 -0.026 -4.137 0.000 -0.039
4:WL-X -1.199 0.103 -0.263 -0.314 -0.001 1.051
5:WL-Z -0.000 -0.000 -0.264 -0.148 0.000 0.000
6:DL+WL UP -0.052 -8.529 0.035 5.593 -0.000 0.051
7:DL+WLDW 0.050 7.825 -0.031 -5.038 0.000 -0.049
8:DL+WL-X -1.189 1.563 -0.268 -1.214 -0.001 1.041
9:DL+WL-Z 0.010 1.460 -0.270 -1.048 0.000 -0.010
10:DL+WLUP+WL-Z -0.052 -8.529 -0.230 5.445 -0.000 0.051
11:DL+WL DW+WL-Z0.050 7.825 -0.295 -5.186 0.000 -0.049
12:DL+WLUP+WL-X-1.252 -8.426 -0.228 5.279 -0.001 1.103
13:DL+WL DW+WL-X-1.149 7.928 -0.294 -5.352 -0.001 1.002
11 1:DL -0.003 1.852 0.005 -1.065 -0.000 0.003
2:WL-U 0.020 -12.950 -0.040 7.735 0.000 -0.020
3:WL- D -0.013 8.251 0.026 -4.928 -0.000 0.013
4:WL-X -1.242 -0.004 0.024 0.004 -0.001 1.094
5:WL-Z 0.000 0.000 -0.264 -0.148 -0.000 -0.000
6:DL+WL UP 0.017 -11.098 -0.035 6.670 0.000 -0.017
7:DL+WLDW -0.016 10.103 0.031 -5.993 -0.000 0.016
8:DL+WL-X -1.245 1.848 0.029 -1.061 -0.001 1.097
9:DL+WL-Z -0.003 1.852 -0.259 -1.213 -0.000 0.003
10:DL+WLUP+WL-Z 0.017 -11.098 -0.299 6.522 0.000 -0.017
11:DL+WL DW+WL-Z-0.016 10.103 -0.234 -6.141 -0.000 0.016
12:DL+WLUP+WL-X-1.224 -11.102 -0.011 6.674 -0.001 1.077
13:DL+WL DW+WL-X-1.258 10.100 0.055 -5.989 -0.001 1.109
21 1:DL 0.003 1.852 0.005 -1.065 0.000 -0.003
2:WL-U -0.020 -12.950 -0.040 7.735 -0.000 0.020
3:WL- D 0.013 8.251 0.026 -4.928 0.000 -0.013
4:WL-X -1.242 0.004 -0.024 -0.004 -0.001 1.094
5:WL-Z -0.000 0.000 -0.264 -0.148 0.000 0.000
6:DL+WL UP -0.017 -11.098 -0.035 6.670 -0.000 0.017
7:DL+WLDW 0.016 10.103 0.031 -5.993 0.000 -0.016
8:DL+WL-X -1.239 1.855 -0.019 -1.069 -0.001 1.091
9:DL+WL-Z 0.003 1.852 -0.259 -1.213 0.000 -0.003
10:DL+WLUP+WL-Z -0.017 -11.098 -0.299 6.522 -0.000 0.017
11:DL+WL DW+WL-Z0.016 10.103 -0.234 -6.141 0.000 -0.016
12:DL+WLUP+WL-X-1.259 -11.095 -0.059 6.666 -0.001 1.111
13:DL+WL DW+WL-X-1.226 10.107 0.007 -5.997 -0.001 1.078
31 1:DL -0.010 1.460 -0.005 -0.900 -0.000 0.010
2:WL-U 0.063 -9.989 0.040 6.493 0.000 -0.061
3:WL- D -0.040 6.365 -0.026 -4.137 -0.000 0.039
4:WL-X -1.199 -0.103 0.263 0.314 -0.001 1.051
5:WL-Z 0.000 -0.000 -0.264 -0.148 -0.000 -0.000

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 163 of 166
Job No Sheet No Rev
164
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Reactions Cont...
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
6:DL+WL UP 0.052 -8.529 0.035 5.593 0.000 -0.051
7:DL+WLDW -0.050 7.825 -0.031 -5.038 -0.000 0.049
8:DL+WL-X -1.210 1.357 0.258 -0.586 -0.001 1.062
9:DL+WL-Z -0.010 1.460 -0.270 -1.048 -0.000 0.010
10:DL+WLUP+WL-Z 0.052 -8.529 -0.230 5.445 0.000 -0.051
11:DL+WL DW+WL-Z-0.050 7.825 -0.295 -5.186 -0.000 0.049
12:DL+WLUP+WL-X-1.147 -8.632 0.298 5.907 -0.001 1.000
13:DL+WL DW+WL-X-1.250 7.721 0.232 -4.723 -0.001 1.101

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 100CU40X2 60CU30X1.6 0.814 1.000 0.814 Bend Z + She 2 1.825 10.236 1.632 0.016
2 100CU40X2 100CU50X2 0.915 1.000 0.915 Bend Z + She 2 3.851 61.064 9.687 0.051
3 100CU40X2 200CU50X4 0.716 1.000 0.716 Bend + Compr 2 11.405 592.857 21.994 0.608
4 100CU40X2 180CU50X3.15 0.776 1.000 0.776 Bend + Compr 2 8.451 370.188 17.362 0.280
5 100CU40X2 90CU50X3.15 0.989 1.000 0.989 Bend + Compr 2 5.616 71.370 14.087 0.186
6 100CU40X2 100CU40X1.6 0.881 1.000 0.881 Bend + Compr 2 2.785 41.990 4.250 0.024
7 140CS60X3.15150CS50X3.15 0.876 1.000 0.876 Bending Z 2 8.397 271.603 27.276 0.278
8 40LU20X2 30LU30X1.6 0.742 1.000 0.742 Bend Y + She 4 0.912 1.328 0.305 0.008
9 40LU20X2 40LU40X2 0.908 1.000 0.908 Bend Y + She 4 1.526 4.019 0.914 0.020
10 100CU40X2 70CU30X1.6 0.895 1.000 0.895 Bend Z + She 2 1.985 14.669 1.715 0.017
11 100CU40X2 90CU50X3.15 0.949 1.000 0.949 Bend Z + She 2 5.616 71.370 14.087 0.186
12 100CU40X2 200CU50X4 0.890 1.000 0.890 Bend + Compr 2 11.405 592.857 21.994 0.608
13 100CU40X2 180CU50X3.15 0.954 1.000 0.954 Bend + Compr 2 8.451 370.188 17.362 0.280
14 100CU40X2 100CU60X3.15 0.893 1.000 0.893 Bend + Compr 2 6.561 106.008 24.202 0.217
15 100CU40X2 90CU40X2 0.986 1.000 0.986 Bend + Compr 2 3.251 40.198 5.055 0.043
16 140CS60X3.15140CS60X3.15 0.998 1.000 0.998 Bend Z + She 2 8.712 259.593 41.703 0.288
17 40LU20X2 30LU30X1.6 0.742 1.000 0.742 Bend Y + She 4 0.912 1.328 0.305 0.008
18 40LU20X2 40LU40X2 0.908 1.000 0.908 Bend Y + She 4 1.526 4.019 0.914 0.020
19 100CU40X2 70CU30X1.6 0.895 1.000 0.895 Bend Z + She 2 1.985 14.669 1.715 0.017
20 100CU40X2 100CU40X3.15 0.987 1.000 0.987 Bending Z 2 5.301 76.461 7.806 0.175
21 100CU40X2 200CU50X4 0.890 1.000 0.890 Bend + Compr 2 11.405 592.857 21.994 0.608
22 100CU40X2 180CU50X3.15 0.956 1.000 0.956 Bending Z 2 8.451 370.188 17.362 0.280
23 100CU40X2 100CU60X3.15 0.893 1.000 0.893 Bend + Compr 2 6.561 106.008 24.202 0.217
24 100CU40X2 90CU40X2 0.986 1.000 0.986 Bend + Compr 2 3.251 40.198 5.055 0.043
25 140CS60X3.15140CS60X3.15 0.998 1.000 0.998 Bend Z + She 2 8.712 259.593 41.703 0.288
26 40LU20X2 30LU30X1.6 0.742 1.000 0.742 Bend Y + She 4 0.912 1.328 0.305 0.008
27 40LU20X2 40LU40X2 0.908 1.000 0.908 Bend Y + She 4 1.526 4.019 0.914 0.020
28 100CU40X2 60CU30X1.6 0.814 1.000 0.814 Bend Z + She 2 1.825 10.236 1.632 0.016
29 100CU40X2 100CU50X2 0.915 1.000 0.915 Bend Z + She 2 3.851 61.064 9.687 0.051
30 100CU40X2 200CU50X4 0.716 1.000 0.716 Bend + Compr 2 11.405 592.857 21.994 0.608

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 164 of 166
Job No Sheet No Rev
165
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
31 100CU40X2 180CU50X3.15 0.778 1.000 0.778 Bending Z 2 8.451 370.188 17.362 0.280
32 100CU40X2 90CU50X3.15 0.989 1.000 0.989 Bend + Compr 2 5.616 71.370 14.087 0.186
33 100CU40X2 100CU40X1.6 0.881 1.000 0.881 Bend + Compr 2 2.785 41.990 4.250 0.024
34 140CS60X3.15150CS50X3.15 0.871 1.000 0.871 Bending Z 2 8.397 271.603 27.276 0.278
35 40LU20X2 30LU30X1.6 0.742 1.000 0.742 Bend Y + She 4 0.912 1.328 0.305 0.008
36 40LU20X2 40LU40X2 0.908 1.000 0.908 Bend Y + She 4 1.526 4.019 0.914 0.020
37 90CS40X2 50CS40X1.25 0.993 1.000 0.993 Bending Z 2 1.759 7.559 3.869 0.009
38 90CS40X2 50CS40X1.6 0.867 1.000 0.867 Bending Z 2 2.210 9.324 4.724 0.019
39 90CS40X2 50CS50X1.6 0.879 1.000 0.879 Bending Z 2 2.530 11.198 8.212 0.022
40 90CS40X2 50CS40X1.6 0.966 1.000 0.966 Bending Z 2 2.210 9.324 4.724 0.019
41 90CS40X2 50CS50X1.6 0.984 1.000 0.984 Bending Z 2 2.530 11.198 8.212 0.022
42 90CS40X2 50CS50X1.6 0.891 1.000 0.891 Bending Z 2 2.530 11.198 8.212 0.022
43 90CS40X2 50CS50X1.6 0.929 1.000 0.929 Bending Z 2 2.530 11.198 8.212 0.022
44 90CS40X2 50CS50X1.6 0.825 1.000 0.825 Bending Z 2 2.530 11.198 8.212 0.022
45 90CS40X2 50CS50X1.6 0.981 1.000 0.981 Bending Z 2 2.530 11.198 8.212 0.022
46 90CS40X2 50CS50X1.6 0.889 1.000 0.889 Bending Z 2 2.530 11.198 8.212 0.022
47 90CS40X2 50CS50X1.6 0.878 1.000 0.878 Bending Z 2 2.530 11.198 8.212 0.022
48 90CS40X2 50CS50X1.6 0.769 1.000 0.769 Bending Z 2 2.530 11.198 8.212 0.022
49 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
50 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
51 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
52 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
53 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
54 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
55 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
56 90CS40X2 50CS25X1.25 0.996 1.000 0.996 Bending Z 2 1.384 5.331 1.245 0.007
57 90CS40X2 50CS50X1.6 0.981 1.000 0.981 Bending Z 2 2.530 11.198 8.212 0.022
58 90CS40X2 50CS50X1.6 0.889 1.000 0.889 Bending Z 2 2.530 11.198 8.212 0.022
59 90CS40X2 50CS50X1.6 0.878 1.000 0.878 Bending Z 2 2.530 11.198 8.212 0.022
60 90CS40X2 50CS50X1.6 0.779 1.000 0.779 Bending Z 12 2.530 11.198 8.212 0.022
61 Cir 0.01 N/A 0.785 0.049 0.049 0.098
62 Cir 0.01 N/A 0.785 0.049 0.049 0.098
63 90CS40X2 50CS50X1.6 0.984 1.000 0.984 Bending Z 2 2.530 11.198 8.212 0.022
64 90CS40X2 50CS50X1.6 0.891 1.000 0.891 Bending Z 2 2.530 11.198 8.212 0.022
65 90CS40X2 50CS50X1.6 0.929 1.000 0.929 Bending Z 2 2.530 11.198 8.212 0.022
66 90CS40X2 50CS50X1.6 0.825 1.000 0.825 Bending Z 2 2.530 11.198 8.212 0.022
67 Cir 0.01 N/A 0.785 0.049 0.049 0.098
68 Cir 0.01 N/A 0.785 0.049 0.049 0.098
69 90CS40X2 50CS40X1.25 0.993 1.000 0.993 Bending Z 2 1.759 7.559 3.869 0.009
70 90CS40X2 50CS40X1.6 0.867 1.000 0.867 Bending Z 2 2.210 9.324 4.724 0.019
71 90CS40X2 50CS50X1.6 0.879 1.000 0.879 Bending Z 2 2.530 11.198 8.212 0.022
72 90CS40X2 50CS40X1.6 0.966 1.000 0.966 Bending Z 2 2.210 9.324 4.724 0.019
73 Cir 0.01 N/A 0.785 0.049 0.049 0.098
74 Cir 0.01 N/A 0.785 0.049 0.049 0.098

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 165 of 166
Job No Sheet No Rev
166
Part
Software licensed to
Job Title Ref

By Date24-Jun-19 Chd

Client File test2.std Date/Time 26-Jun-2019 18:33

Failed Members
There is no data of this type.

Print Time/Date: 26/06/2019 18:40 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 166 of 166

You might also like