…

Title
(Binding Page)

Author

Name of Student Student’s Registration Number

Submitted To

Dr. Abid Hussain

DEPARTMENT OF MECHANICAL ENGINEERING

Author

Name of Student Student’s Registration Number

A semester project submitted in partial fulfillment of the requirements for the course of

Heat and Mass Transfer

DEPARTMENT OF MECHANICAL ENGINEERING

i
 Abstract

Title

Write abstract from here. The font of the entire document is Times New Roman size 12,

regular, justified except headings. The length of the abstract should not exceed 1 page at

maximum.

Keywords:

ii
 UNDERTAKING

Use the following undertaking as it is.

I/WE certify that project titled “enter title of your project here” is my/our own work. The

work has not been presented elsewhere for assessment. Where material has been used

from other sources it has been properly acknowledged / referred.

Signature of Student

Name of Student

Registration Number

iii
 ACKNOWLEDGEMENTS

Write acknowledgment here. Use Times New Roman 12, justified.

iv
 TABLE OF CONTENTS

Sample is given below:

Abstract.................................................................................................................ii

Acknowledgement...............................................................................................iii

List of Figures ..................................................................................................... vi

List of Tables ................................................................................................. vii

Abbreviations ................................................................................................... viii

Chapter I: Introduction ......................................................................................... 1

1.1 Statement of the Problem ......................................................................1

1.2 Objectives................................................................................................. 3

1.3 Organization of the Thesis ....................................................................3

Chapter II: Overview of xyz scheme ................................................................... 4

v
 LIST OF FIGURES

Sample is given below:

Number Page

Fig 2.1Block diagram of xyz block ..................................................................8

Fig 2.2 Basis process Diagram .........................................................................9

Fig 2.3 Block Diagram of manufacturing steps .............................................10

Fig 3.1Discharge rate .....................................................................................13

vi
 LIST OF TABLES

Similar to the list of figures.

vii
 ABBREVIATIONS

Abbreviations should be placed at the end. Sample is given below:

FYP: Final Year Project

UG: Undergraduate Studies

MED: Mechanical Engineering Department

viii
 CHAPTER 1

Name of Chapter

1.1 Heading 1

All main headings in Times New Roman font size 14, bold. All the text in Times New

Roman font size 12, regular, justified & in double line spacing format.

1.1.1 Subheading 1

All subheadings in Times New Roman font size 12, bold.

1.1.1.1 Subheading 2

1.2 Heading 2

1
 CHAPTER 2

Name of Chapter 2

2.1 Figure Style

All figures should be centrally aligned with captions at bottom of figure.

Fig 2.1: Autumn in Osaka, Japan

2.2 Table Style

All tables should be centrally aligned with captions at the top as sample given below:

Table 2.1: xyz

2.3 Equations Style

All equations should be centrally aligned with proper numbering. Use Microsoft Word

Equation Editor. E.g.,

E = mc2
(2.1)

2
 CONCLUSION

Write conclusion of your FYP here. Maximum of 1 page.

3
 REFERENCES

Use following style format for references.

Example Journal Paper:

[1] Ling Z, Chen J, Fang X, Zhang Z, Xu T, Gao X, et al. Experimental and numerical

investigation of the application of phase change materials in a simulative power

batteries thermal management system. Appl Energy 2014; 121:

104-13.

Example Conference Paper:

[2] Meinert J. Cellular metals and composites for an optimization of the loading

and re-loading behavior of thermal storages. In: 4th International renewable

energy storage conference. Winterbergstrasse: Fraunhofer Institute of

Manufacturing and Applied Materials, Dresden Branch Lab; 2009. p. 28.

Example Book:

[3] David L, Thomas BR. Handbook of batteries. New York: McGraw-Hill; 2002.

Example Web Link:

[4] MPEG Software Simulation Group, “The MSSG homepage”, available on-line at

http://www.mpeg.org/MPEG/ MSSG, 2004.

4
 ANNEXURE

Annexure (if any) should be placed at the end of thesis report.

Hard Copy Information:

Page Size: Letter (8.5” x 11”)

Page Margins: Top & Bottom = 1” and Left & Right = 1.25”

Page orientation: Portrait

Line Spacing: 1.5

Page Numbering: Bottom Center

Printing: double Side