Scribd
Upload
41 views

Module 7: Planes of Weakness in Rocks: 7.2.10 Joint Friction Angle

The document discusses shear strength properties of rock discontinuities. It defines peak and residual shear strength, with the residual being lower than peak strength once surface irregularities are worn down. Typical friction angles are given for different rock types, from low to high. Equations are presented for calculating shear stress on inclined surfaces based on normal stress and friction angle. Finally, the concept of asperities - surface irregularities - is introduced and their role in shear strength properties.

Uploaded by

فردوس سليمان
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
41 views

Module 7: Planes of Weakness in Rocks: 7.2.10 Joint Friction Angle

The document discusses shear strength properties of rock discontinuities. It defines peak and residual shear strength, with the residual being lower than peak strength once surface irregularities are worn down. Typical friction angles are given for different rock types, from low to high. Equations are presented for calculating shear stress on inclined surfaces based on normal stress and friction angle. Finally, the concept of asperities - surface irregularities - is introduced and their role in shear strength properties.

Uploaded by

فردوس سليمان
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Module 7: Planes of weakness in rocks

LECTURE 25
7.2.10 Joint Friction Angle

During the shear test at constant normal stress, at small displacement specimen
behaves elastically and the shear stress increases linearly with displacement. As the force
resisting movement is overcome, the curve become non-linear and reaches a maximum that
represent peak shear strength of the discontinuity. Thereafter, the stress required to cause
displacement decreases and eventually reaches a constant value termed as the residual shear
strength.
Peak shear strength (𝜏𝜏) = c + σ tan ϕ P
Residual shear strength (𝜏𝜏) = σ tan ϕ R
For the residual strength condition, the cohesion is lost once displacement has broken by the
cementing action. The residual friction angle is always less than the peak friction angle
because the shear displacement grinds the minor irregularities on the rock surface and
produces a smoother lower friction surface.
For a planar, clean (no-infilling) discontinuity, the cohesion will be zero and the shear
strength will be defined solely by the friction angle. The friction angle of the rock material is
related to the grains exposed on the fractured surface.
Thus, a fine grained rock and rock with a high mica content aligned parallel to the surface
such as phyllite, will tend to have a low friction angle while, a course grained rock such as
granite will have high friction angle.

Shear
Normal stress (σ)
Displacement

Shear Stress (𝜏𝜏)

Shear
Stress (𝜏𝜏)
Normal stress (σ)

Figure 7.14: Normal and shear stress representation of shearing block

215
Module 7: Planes of weakness in rocks

Peak shear strength

Residual shear strength

Shear
Stress (𝜏𝜏)

Increasing
normal stress

Shear Displacement (δ)

Figure 7.15: Plot between shear displacement versus shear stress

Peak strength
𝜏𝜏 = c + σ tan ϕP
Shear
Stress (𝜏𝜏) ϕP
ϕR Residual strength
𝜏𝜏 = σ tan ϕR

Normal Stress (δ)

Figure 7.16: Mohr plots for peak and residual strength

Table 7.4: Typical ranges of friction angle for a variety of rock types

Rock class Friction angle range Typical rocks

Low friction 20-27 Schist, shale

Medium friction 27-34 Sandstone, siltstone

High friction 34-40 Basalt, granite, limestone

216
Module 7: Planes of weakness in rocks

(ϕ + i)
ϕ

Shear stress

Normal stress

(a)

Normal load

i
Shear displacement

(b)

Figure 7.17: Definition of shear strength of discontinuity surface

𝜎𝜎
𝜏𝜏 'i'
σi
𝜏𝜏𝑖𝑖

𝜏𝜏
𝜎𝜎

Figure 7.18 : Shearing alone inclined surface

217
Module 7: Planes of weakness in rocks

𝜏𝜏𝑖𝑖 = 𝜏𝜏𝑐𝑐𝑐𝑐𝑐𝑐 2 𝑖𝑖 − 𝜎𝜎 sin 𝑖𝑖 cos 𝑖𝑖 (7.8)

𝜎𝜎𝑖𝑖 = 𝜎𝜎 𝑐𝑐𝑐𝑐𝑐𝑐 2 𝑖𝑖 + 𝜏𝜏 sin 𝑖𝑖 cos 𝑖𝑖 (7.9)

If the discontinuity surface has zero cohesion

𝜏𝜏𝑖𝑖 = 𝜎𝜎𝑖𝑖 tan ∅ (7.10)

(𝜏𝜏𝑐𝑐𝑐𝑐𝑐𝑐 2 𝑖𝑖 − 𝜎𝜎 sin 𝑖𝑖 cos 𝑖𝑖) = (𝜎𝜎 𝑐𝑐𝑐𝑐𝑐𝑐 2 𝑖𝑖 + 𝜏𝜏 sin 𝑖𝑖 cos 𝑖𝑖) tan ∅ (7.11)

𝜏𝜏 = 𝜎𝜎 tan(∅ + 𝑖𝑖) (7.12)

Equation for patton's law is valid at low normal stresses where shear displacement is due to
sliding along the inclined surfaces. At higher normal stresses, the strength of the intact
material will be exceeded and the teeth will tend to break off, resulting in a shear strength
behaviour which is more closely related to the intact material strength than to the frictional
characteristics of the surfaces. While Patton’s approach has the merit of being very simple, it
does not reflect the reality that changes in shear strength with increasing normal stress are
gradual rather than abrupt.

First order asperities

2nd order asperities

Figure 7.19 : Different orders of asperities

218

You might also like