11) With the ball in the closed position, thread the retainer into the body and

torque to manufacturing specification to secure the body joint. Tighten to the

torque values shown in the table below.

12) Cycle the valve to the open position and verify proper operation and alignment
of handle and/or mechanism.
A Division of Conbraco Industries, Inc. Matthews, NC Pageland, SC Conway, SC
Note: Always test valve and system before putting the system into service.

Table 1: Torque Requirements 2 PIECE THREADED AND SOLDER END

BALL VALVES
Gland Nut Torque Retainer Torque Gland Nut Torque Retainer Torque
(+ or – 10%) (+ or – 10%) Valve Size (+ or – 10%) (+ or – 10%) INSTALLATION, OPERATION, & MAINTENANCE GUIDE
(ft-lb) (ft-lb) (ft-lb) (ft-lb)
BRONZE STEEL
10 - 12 13 1/4" - 3/8" 12 - 18 13
10 - 12 16 1/2" 12 - 18 16
15 - 20 42 3/4" 20 - 25 42
15 - 20 63 1" 20 - 25 63
35 - 40 130 1-1/4" 61-100 130
35 - 40 199 1-1/2" 61-100 199
35 - 40 282 2" 61-100 282
35 - 40 686 2-1/2" 61-100 681
35 - 40 905 3" 61-100 905
35 - 40 1849 4" - -

PARTS ILLUSTRATION

HANDLE
STEM
HANDLE NUT

GLAND SCREW
RETAINER STEM PACKING
SEAT STEM BEARING

BODY

BALL

Page 4 I845300. Rev A Page 1

 INSTALLATION MAINTENANCE
Two piece threaded and solder end Apollo Ball valves are bi-directional. They may be Regular Maintenance
installed in vertical or horizontal pipe runs without regard to flow direction and without Normal stem packing wear can be compensated for by tightening the packing gland
regard to stem orientation. screw. (Wrench part number H371400 is available to ease this operation.) Tighten the
packing gland screw clockwise in 1/8 turn increments until observed leakage stops. Do
Note: Valves must be installed in piping systems that comply with the applicable not exceed the values shown in Table 1. If all of the adjustments to the packing gland
portions of the ASME B31 standards. Special considerations must be taken with screw have been made, remove the handle nut, handle and packing gland screw and
respect to pipe line expansions and contractions and the media expansion and add one or two replacements bearings on top of the old packing. Reinstall the handle
contractions within the piping system. and handle nut.
Caution: Do not disassemble valve while under pressure nor with entrapped hazardous
Threaded End Valves fluids therein.
Pipe connections to be threaded into these valves should be accurately threaded, clean
and free of foreign material or metal shavings. PTFE pipe tape is recommended for use Valve Repair
as the pipe joint sealant. Two wrenches must be used when making up pipe joints to Disassembly
these valves. Apply one wrench on the valve end closest to the pipe joint being 1) Operate the valve fully opened to fully closed to assure there are no trapped
tightened and the other wrench to the pipe to prevent transmitting torque through the fluids or pressure in the body cavity. Leave the valve in the closed position.
valve body joint. Typical pipe make-up is 1-1/2 turns after installing the pipe hand-tight. 2) Remove the handle nut, handle and packing nut. Set aside for reuse.
3) Install pipe plugs in the body and retainer ports of NPT valves to prevent
Union End Valves: collapsing those areas.
Remove the union nut from the valve and place onto pipe. Thread the tailpiece onto the 4) Remove the retainer from the body. It may be necessary to heat the body joint
pipe using a smooth jaw wrench. Thread the union nut onto the valve body and lightly above 450°F to breakdown the sealant used to secure the valve halves.
torque. 5) Remove the ball from the body cavity. Inspect the ball. If it is scarred, it is
recommended that the whole valve be replaced, but replacement balls are
Solder End (Sweat In) Valves available. Clean and set aside good balls for reuse.
Caution: Use only solders with melt points below 500°F. 6) Push the stem from the outside into the body cavity. Inspect the stem. If it is
Caution: Valves should only be soldered in the fully open position. scarred or has damaged threads, replacements are available. Clean and set
aside good stems for reuse.
During soldering, the mid-portion of the valve body should not exceed 300°F. This can 7) Remove all seals and seats from the body and retainer then discard. Inspect
be monitored using Tempilstik® or an infra-red temperature sensor. Depending on the the body and retainer for damage. If damaged, scrap the valve as
fuel selected and the orientation of the installation it may be necessary to wrap the replacements of these components are not offered.
valve body with wet rags or employ other heat absorbing techniques. The flame must
be directed away from the valve body, concentrated on the solder cup. The cup should Note: Union end valves cannot be easily repaired; therefore it is recommended
be heated evenly. Once one of the joints is complete, the valve should be allowed to that the main valve section be replaced.
cool until "cool to the touch" before beginning the second joint.
Re-Assembly
Fuel Flame temp w/Oxygen 1) Install stem bearing on to stem.
Propane 5122°F (2828°C) 2) Fit stem into body from the retainer end and position the stem with the handle
Propylene 5245°F (2896°C) flats perpendicular to the flow axis.
MAPP Gas 5389°F (2976°C) 3) Install stem packing over stem and fit into body recess.
Acetylene 5720°F (3160°C) 4) Install packing gland screw into the threaded stem area.
5) Tighten the gland screw to manufacturing torque specifications: Tightened to
Warning: Excessive heat input will damage the body seal resulting in leaks at the valve the torque values shown in Table 1.
body joint. In extreme cases, seats and stem packing may also be damaged. 6) Install the handle and handle retaining hardware.
7) Apply suitable light lubricant to seat and fit into the seat pocket of the body.
OPERATION 8) Install the ball in the closed position.
The valve handle is marked showing proper rotation direction for “ON” and “OFF” 9) Apply suitable light lubricant to seat and fit into the seat pocket of the retainer.
positions. Rotation is clockwise for “OFF” (closed) and counterclockwise for “ON” 10) Apply an adequate amount of thread locking compound (Loctite® 609, 648 or
(open). 680) to the retainer threads so that it covers no less than two complete
threads opposite of the retainer shoulder.
Note: Valves in oxygen service can only be sealed with oxygen compatible thread sealant.

Page 2 Page 3
Warning: (Required by California) This product contains a chemical known to the state
of California to cause Cancer and Birth Defects or other Reproductive Harm.