HX-WCS, HX-2.

5GHz TDD Remote

and EPM
Training and Troubleshooting Guide

Presenter Name
Presenter Title
Business Unit

Date
Information Security

This presentation contains Corning Restricted

information and is intended solely for those
with a need to know. It may not be distributed,
in whole or part, in any form by any means, or
by any person or organization without
authorization from Corning Incorporated.
Contents
• System overview
• GUI review
• Typical field issues
• Power connection
• RF Adjustment
• Module replacement
1. Fan replacement
2. HX-Module replacement
• Connection guidance with EPM and 2K’s

.
Business Name Corning Restricted 3 .
.
System Overview

• Remote block diagrams

• Link budget details for uplink and downlink (Plus gain range
parameters)
• Pictures of each sections of modules and label
• LED outlines
• Functions of each ports

.
Business Name Corning Restricted 4 .
.
System Overview

• Remote Block Diagram – HX-WCS

.
Business Name Corning Restricted 5 .
.
System Overview

• Remote Block Diagram – HX-2.5GHz TDD

.
Business Name Corning Restricted 6 .
.
System Overview

• Link budget – HX-WCS System Budget

DL path: BU Input level -20 dBm, Optical output level from BU 0÷-2 dBm, HX-WCS UNIT output level
(at each antenna port) 21-33dBm (130mW to 2W)

Optical Fiber Loss Compensation Atten : 8dB (Optic Fiber Loss 0~4dBo)

BU Gain Compensation Atten : 2dB
UL path: Optical output level from HX-WCS UNIT 2.5÷5 dBm, Output level from BU -10 dBm

Gain setting Range : 21dB ~ 41dB

.
Business Name Corning Restricted 7 .
.
System Overview

• HX-WCS Budget

Optic Module HPA Module Cavity Module

Budget After PD Remark
Output Output Output
Down Link -56.5~-48.5dBm -5dBm +35dBm +33dBm

Cavity Optic Module

Budget Before LD Remark
Module Input Input
-41dBm -43dBm -10dBm Normal Gain
Up Link
-31dBm -33dBm -10dBm Min Gain
.
Business Name Corning Restricted 8 .
.
System Overview

• Link budget - HX-2.5GHz TDD System Budget

DL path: OCH Input level -20 dBm, Optical output level from OCH 0÷-2 dBm, HX-2.5GHz TDD UNIT
output level (at each antenna port) 21-33dBm (130mW to 2W)

Optical Fiber Loss Compensation Atten : 12dB (Optic Fiber Loss 0~6dBo)

OCH Gain Compensation Atten : 2dB
UL path: Optical output level from HX-2.5GHz TDD UNIT 2.5÷5 dBm, Output level from OCH -10 dBm

Gain setting Range : 21dB ~ 41dB

.
Business Name Corning Restricted 9 .
.
System Overview

• HX-2.5GHz TDD Budget

Optic Module HPA Module Cavity Module

Budget After PD Remark
Output Output Output
Down Link -52~-40dBm -5dBm +35dBm +33dBm

Cavity Optic Module

Budget Before LD Remark
Module Input Input
-41dBm -28dBm -7dBm Normal Gain
Up Link
-31dBm -18dBm -7dBm Min Gain
.
Business Name Corning Restricted 10 .
.
System Overview

• Pictures of each sections of modules and label – HX-WCS

– HX-WCS Module

.
Business Name Corning Restricted 11 .
.
System Overview

• Pictures of each sections of modules and label – HX-WCS

– Label (position)

.
Business Name Corning Restricted 12 .
.
System Overview

• Pictures of each sections of modules and label – HX-WCS

Marketing Label FCC & MET Label

.
Business Name Corning Restricted 13 .
.
System Overview

• Pictures of each sections of modules and label – HX-2.5GHz TDD

– HX-2.5GHz TDD Module

.
Business Name Corning Restricted 14 .
.
System Overview

• Pictures of each sections of modules and label – HX-WCS

– HX-2.5GHz TDD Label

.
Business Name Corning Restricted 15 .
.
System Overview

• Pictures of each sections of modules and label – HX-2.5GHz TDD

Marketing Label FCC & MET Label

.
Business Name Corning Restricted 16 .
.
System Overview

• LED outlines – HX-WCS

HX-WCS RCU Module Status LEDs

.
Business Name Corning Restricted 17 .
.
System Overview

• LED outlines – HX-WCS

LED State Description
From HE Run Blinking green Power input detected
(from Off Unit powered off
headend) Comm Green Short blink upon receiving FSK message (Off at any other time)
Link Steady green Optical link level is above normal threshold
Blinking green Optical link level is lower than Normal threshold but above no-link threshold
Off Optical link level is below No link threshold
Status Green / Yellow / Color according to device’s overall status
Red * Set by the service most severe alarm.
* Yellow(minor alarm): Optic link(HE/Remote), Door, FAN(minor), RF
Adjustment, Ext. Alarm
To Remote Comm Green Short blink upon receiving FSK message (Off at any other time)
Link Steady green Optical link level is above normal threshold
Blinking green Optical link level is lower than Normal threshold but above no-link threshold
Off Optical link level is below No link threshold
Device Service Green Service status is ok
Red Any service alarm occurs
Ant. Green VSWR alarm is clear
Red VSWR alarm occurs
Temp. Green Over Temp and Temperature Protection alarms are clear
Red Over Temp or Temperature Protection alarms occur
Fan Green Fan alarm is clear
Yellow Fan alarm occurs (minor) for first fan faulty
Red Fan alarm occurs (major) for other fan faulty.
.
Business Name Corning Restricted 18 .
.
System Overview

• LED outlines – HX-WCS

HX-WCS Internal Module LEDs

.
Business Name Corning Restricted 19 .
.
System Overview

• LED outlines – HX-WCS

Module LED Description
PSU Run Steady green – required power input detected
Off – no power input
PSU Off – normal operation
Steady red – faulty PSU module; In more than 10% difference than the
rated DC output, the red LED occurs.
HX-WCS BU Link Off – No optical link
Module Blinking green – Low optical link level
Steady green – Normal optical link level
Run Off – no power input
Blinking green – power input detected
Remote Link Off – No optical link
Note: Indicates link status
between HX WCS and Blinking green – Low optical link level
additional remote unit
Steady green on – Normal optical link level
connected.

.
Business Name Corning Restricted 20 .
.
System Overview

• LED outlines - HX-2.5GHz TDD

HX-2.5GHz TDD RCU Module Status LEDs

.
Business Name Corning Restricted 21 .
.
System Overview

• LED outlines - HX-2.5GHz TDD

LED State Description
Run Steady green Power input detected
Off Unit power is off
Comm Green Short blink upon receiving FSK message(Off at any other time)
Link Steady green Optical link level is above normal threshold
Blinking green Optical link level is lower than normal threshold but above no-link threshold
Off Optical link level is below No link threshold
Status Green / Yellow / Red Color according to device’s overall status
* Set by the service most severe alarm.
* Yellow(minor alarm): Optic link, Door, FAN(minor), RF Adjustment, Ext. Alarm
Service Green Service status is ok
Red Any service alarm occurs
Ant. Green VSWR alarm is clear
Red VSWR alarm occurs
Temp. Green Over Temp and Temperature Protection alarms are clear
Red Over Temp or Temperature Protection alarms occur
T-Sync Green TDD sync locked
Red TDD sync error (unlocked)
Fan Green Fan alarm is clear
Yellow Fan alarm occurs (minor) for first fan faulty
Red Fan alarm occurs (minor or major) for more than one faulty fan
.
Business Name Corning Restricted 22 .
.
System Overview

• LED outlines - HX-2.5GHz TDD

HX-2.5GHz TDD Internal Module LEDs

.
Business Name Corning Restricted 23 .
.
System Overview

• LED outlines - HX-2.5GHz TDD

Module LED Description
PSU Run
Steady green – required power input detected
Off – no power input
PSU
Off – normal operation
Steady red – faulty PSU module; In more than 10% difference than the rated DC
output, the red LED occurs.

HX-2.5 GHz Link Off – No optical link

TDD Module
Blinking green – Low optical link level
Steady green – Normal optical link level
Run Off – no power input
Blinking green – power input detected

.
Business Name Corning Restricted 24 .
.
System Overview

• Functions of each ports – HX-WCS

HX-WCS Front Panel Interfaces

.
Business Name Corning Restricted 25 .
.
System Overview

• Functions of each ports – HX-WCS

Connector Description

ANT 4.3-10 Type duplexed antenna port

4.3-10 Type duplexed wideband remote unit expansion port for interfacing to external RF In source
WB-RU (i.e. HX4 remote) so that additional services are combined with those of the HX and distributed
from the duplexed HX antenna port

DL Test CPL. Port SMA-Type female 50Ω connector (40 dB ± 2 dB) used for RF DL test

RS-232 D-Type 9 pin female console port used for connecting to engineering GUI

Ethernet (RJ-45) Ethernet connection for local craft

Ext. 1 / Ext. 2 DB-9 female (Future option)

Ext. Alarms DB-9 female external alarm connector for external dry contact alarm connections

GND Two-hole, standard barrel grounding lug

.
Business Name Corning Restricted 26 .
.
System Overview

• Functions of each ports – HX-WCS

HX-WCS Internal Module Interfaces

.
Business Name Corning Restricted 27 .
.
System Overview

• Functions of each ports – HX-WCS

Module Interface Description

PSU Power connector 34-48 V DC input; 6 pin DC terminal block connector

SC APC fiber-optic pair connector; SMF; connection towards Base Unit

(BU)
Optic Port

HX Module SC APC fiber-optic pair connector; SMF; connection towards additional

remote unit

Extension UL/DL SMA type (future option)

.
Business Name Corning Restricted 28 .
.
System Overview

• Functions of each ports - HX-2.5GHz TDD

HX-2.5GHz TDD Front Panel Interfaces

.
Business Name Corning Restricted 29 .
.
System Overview

• Functions of each ports - HX-2.5GHz TDD

Connector Description
ANT. Mini DIN 4.3-10 type duplexed antenna port (one per multiplexer)

CPL. SMA-Type female 50Ω coupling port (-40 dB ± 1.0 dB) used for RF DL test (one per multiplexer)

WB RU N-Type duplexed wideband remote unit expansion port for interfacing to HX4 remote (one per
multiplexer) so that additional HX4 services are combined with those of the HX 2.5 GHz TDD and
distributed from its antenna port
WCS RU Mini DIN 4.3-10 Type duplexed port (one per multiplexer) for interfacing to HX WCS RF input so
that additional WCS service is combined with those of the HX 2.5 GHz TDD and distributed from its
antenna port
Ext. 1 / Ext. 2 N/A (Future option)

GND Two-hole, standard barrel grounding lug

Ext. Alarms DB-9 female external alarm connector for external dry contact alarm connections; Supports up to
four external alarms (configurable via the Web GUI)
RS-232 D-Type 9 pin female console port used for connecting to engineering GUI

T-Sync SMA type connector for TDD sync monitoring

Ethernet Ethernet connection for local craft

.
Business Name Corning Restricted 30 .
.
System Overview

• Functions of each ports - HX-2.5GHz TDD

HX-2.5GHz TDD Internal Module Interfaces

.
Business Name Corning Restricted 31 .
.
System Overview

• Functions of each ports - HX-2.5GHz TDD

Module Interface Description

34-48 V DC input; 8 pin DC terminal block connector (Dinkle

PSU Power connector
2EHDRM-08P)

Optic Port SC APC fiber-optic pair connector; SM fiber; connection towards OCH
HX Module

Extension UL/DL SMA Type connector N/A (future option)

.
Business Name Corning Restricted 32 .
.
GUI Review

• SC-450 GUI review

– The Remote unit is centrally managed via the SC-450 Controller
(HX-WCS: 7.2 and higher, HX-2.5GHz TDD: v7.3 and higher).
– All user's privileges behavior in SC-450 shall apply to the Remote
UNIT units, including access levels and group's assignment.

.
Business Name Corning Restricted 33 .
.
GUI Review

• SC-450 GUI review – HX-WCS

– Module Info

.
Business Name Corning Restricted 34 .
.
GUI Review

• SC-450 GUI review – HX-WCS

Tab Frame Function Name in MIB Behavior Field Content Notes

Name hxnName Read / Write 20 chatrs, standard ASCII

extended name hxnExtendedName Read / Write 45 chatrs standard ASCII

site ID hxnSiteID Read / Write 20 chars, standard ASCII site ID

Subsite ID hxnSubsiteID Read / Write 4 hex Subsite ID

Service hxnService Read Only WCS2300F, SPK2500T Service

hxn (shall contain flavor information - 5 / 2

Device Type hxnDeviceType Read Only Watts, INTL / US, WDM / nonWDM,
SMF/MMF, MIMO / SISO)
Module
Info Firmware version hxnFirmwareVersion Read Only alpha numerical, XX.YY Firmware version

Module Info Product revision hxnProductRevision Read Only alpha numerical, XX.YY Product revision

Serial Number hxnSerialNumber Read Only 7 digit alpha-numerical s/n

hxnController Read Only 01-Sep

hxnConnector Read Only 1-16 Location index combined of :

Location index hxnController\hxnConnector\hxnOptmIx
hxnOptmIx Read Only 1-2 \hxnIx

hxnIx Read Only 1-4

link level hxnLinkLevel Read Only 0-255, raw reading

Laser And
Link status hxnLinkStatus Read Only Off / Low / Normal
Optics
optical adjustment status hxnOpticalAdjustStatus Read Only N/A, Fail, Success

.
Business Name Corning Restricted 35 .
.
GUI Review

• SC-450 GUI review – HX-WCS

– RF Parameters

.
Business Name Corning Restricted 36 .
.
GUI Review

• SC-450 GUI review – HX-WCS

Tab Function Name in MIB Behavior Field Content Notes

Service Control hxnServiceControl Read / Write On / Off

DL Max power hxnDLMaxPower Read / Write DL adjustment target

DL Power Input Level hxnDLPowerInputLevel Read Only

Adjustment result hxnAdjustmentResult Read Only Adjustment result - N/A, Fail, Success

Adjustment date and

hxnAdjustmentDateTime Read Only Last successful adjustment date and time
time

Do Adjust hxnDoAdjust PB

DL DCA Range (total, available for user to

DL Attenuation hxnDLAttenuation Read / Write
set from)
RF Parameters
DL Output power hxnDLOutputPower Read Only Current output power of the remote

UL DCA Range (Total. Available for user to

UL Attenuation hxnULAttenuation Read / Write
set from)
UL Gain setting of the remote, Low,
UL Gain setting hxnULGainSetting Read / Write
Normal, High. Range

Reset hxnReset PB Perfrom soft reset to the unit

frequency, in 0.1Mhz resolution, selection

Center Frequancy hxnTddCenterFrequancy Read / Write TDD only, otheres NA
is done via combo box 2496.0-2690.0

DL\UL\Auto mode to test signal and be only for CMA useres ,TDD only, will
DL\UL test mode Read / Write able to ajust manualy for testing perfesess remain in a status for 4 hours and return
TDD only to Auto

.
Business Name Corning Restricted 37 .
.
GUI Review

• SC-450 GUI review – HX-WCS

– Service Alarms

.
Business Name Corning Restricted 38 .
.
GUI Review

• SC-450 GUI review – HX-WCS

Tab Function Name in MIB Behavior Field Content Notes
Major Severity, ONLY FOR TDD
Sync Alarm hxnSyncAlarmSet Read Only checked / Unchecked via "alarm masking"
REMOTES
Notifiy Severity, ONLY FOR TDD
Sync Alarm hxnSyncAlarmClear Read Only checked / Unchecked via "alarm masking"
REMOTES

Service Off hxnServiceOffSet Read Only checked / Unchecked via "alarm masking" major severity

Service Off hxnServiceOffClear Read Only checked / Unchecked via "alarm masking" Notify severity

DL Output power High hxnOutputPowerHighSet Read Only checked / Unchecked via "alarm masking" minor severity

DL Output power High hxnOutputPowerHighClear Read Only checked / Unchecked via "alarm masking" Notify severity

DL Output power Low hxnOutputPowerLowSet Read Only checked / Unchecked via "alarm masking" major severity
Service Alarms
DL Output power Low hxnOutputPowerLowClear Read Only checked / Unchecked via "alarm masking" Notify severity

VSWR Alarm hxnVSWRAlarmSet Read Only checked / Unchecked via "alarm masking" major severity

VSWR Alarm hxnVSWRAlarmClear Read Only checked / Unchecked via "alarm masking" Notify severity

RF AdjustmentFail hxnAdjustmentFailSet Read Only checked / Unchecked via "alarm masking" Minor severity

RF AdjustmentFail hxnAdjustmentFailClear Read Only checked / Unchecked via "alarm masking" Notify severity

DL Protection activation hxnProtectionActivatedSet Read Only checked / Unchecked via "alarm masking" major severity

DL Protection activation hxnProtectionActivatedClear Read Only checked / Unchecked via "alarm masking" Notify severity

.
Business Name Corning Restricted 39 .
.
GUI Review

• SC-450 GUI review – HX-WCS

Tab Function Name in MIB Behavior Field Content Notes
accumulative for all the service
service 1 overall status hxnServiceOcerallStatus Read Only checked / Unchecked via "alarm masking" allarms(same indicator in GUI but different
severity)
Low Optical Link hxnLowOpticalLinkSet Read Only checked / Unchecked via "alarm masking" minor severity
Low Optical Link hxnLowOpticalLinkClear Read Only checked / Unchecked via "alarm masking" Notify severity
Temprature High hxnTemperatureHighSet Read Only checked / Unchecked via "alarm masking" minor severity
Temprature High hxnTemperatureHighClear Read Only checked / Unchecked via "alarm masking" Notify severity

Temperature protection hxnTemperatureProtectionSet Read Only checked / Unchecked via "alarm masking" major severity
Temperature protection hxnTemperatureProtectionClear Read Only checked / Unchecked via "alarm masking" Notify severity
Fans Minor hxnFansMinorFaultSet Read Only checked / Unchecked via "alarm masking" minor severity, for first fan alarm only
Fans Minor hxnFansMinorFaultClear Read Only checked / Unchecked via "alarm masking" minor severity, for first fan alarm only
Fans Major hxnFansMajorFaultSet Read Only checked / Unchecked via "alarm masking" major severity, For any other fan alarm
General Alarms major severity, For any other fan alarm
Fans Major hxnFansMajorFaultClear Read Only checked / Unchecked via "alarm masking" (same indicator in GUI but different
severity)
optical adjustment hxnOpticalAdjustSet Read Only checked / Unchecked via "alarm masking" minor Severity (not for WCS)
optical adjustment hxnOpticalAdjustClear Read Only checked / Unchecked via "alarm masking" Notify severity (not for WCS)
Door Open hxnDoorOpenAlarmSet Read Only checked / Unchecked via "alarm masking" minor severity

Door Open hxnDoorOpenAlarmClear Read Only checked / Unchecked via "alarm masking" Notify severity
Major Severity, ONLY FOR WCS
Remote Unit optical Link hxnRemoteUnitOpticalLinkSet Read Only checked / Unchecked via "alarm masking"
REMOTES
Notify severity, ONLY FOR WCS
Remote Unit optical Link hxnRemoteUnitOpticalLinkClear Read Only checked / Unchecked via "alarm masking"
REMOTES
Overall Status hxnOverallStatus Read Only
Change name to Alarm Masking
Alarm Masking hxnAlarmMask Read / Write Button
RH: change done

.
Business Name Corning Restricted 40 .
.
GUI Review

• SC-450 GUI review – HX-WCS

– Ext. Alarms

.
Business Name Corning Restricted 41 .
.
GUI Review

• SC-450 GUI review – HX-WCS

Tab Function Name in MIB Behavior Field Content Notes
External Alarm #1 hxnExternalAlarm1Set Read Only checked / Unchecked via "alarm masking" Severity depend on user setting TDD and WCS only
External Alarm #1 hxnExternalAlarm1Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
External Alarm #2 hxnExternalAlarm2Set Read Only checked / Unchecked via "alarm masking" Severity depend on user settingTDD and WCS only
External Alarms WCS External Alarm #2 hxnExternalAlarm2Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
and TDD only External Alarm #3 hxnExternalAlarm3Set Read Only checked / Unchecked via "alarm masking" Severity depend on user settingTDD and WCS only
External Alarm #3 hxnExternalAlarm3Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
External Alarm #4 hxnExternalAlarm4Set Read Only checked / Unchecked via "alarm masking" Severity depend on user settingTDD and WCS only
External Alarm #4 hxnExternalAlarm4Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
Led hxnExternalAlarmStatus1 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask1 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger1 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity1 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName1 Read / Write 20 chars, standard ASCII
chars)TDD and WCS only
Led hxnExternalAlarmStatus2 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask2 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger2 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity2 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName2 Read / Write 20 chars, standard ASCII
External Alarms WCS chars)TDD and WCS only
and TDD only Led hxnExternalAlarmStatus3 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask3 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger3 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity3 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName3 Read / Write 20 chars, standard ASCII
chars)TDD and WCS only
Led hxnExternalAlarmStatus4 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask4 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger4 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity4 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName4 Read / Write 20 chars, standard ASCII
chars)TDD and WCS only

.
Business Name Corning Restricted 42 .
.
GUI Review

• SC-450 GUI review – HX-WCS

– Comment(N/A)

.
Business Name Corning Restricted 43 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

– Module Info

.
Business Name Corning Restricted 44 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

Tab Frame Function Name in MIB Behavior Field Content Notes

Name hxnName Read / Write 20 chatrs, standard ASCII

extended name hxnExtendedName Read / Write 45 chatrs standard ASCII

site ID hxnSiteID Read / Write 20 chars, standard ASCII site ID

Subsite ID hxnSubsiteID Read / Write 4 hex Subsite ID

Service hxnService Read Only WCS2300F, SPK2500T Service

hxn (shall contain flavor information - 5 / 2

Device Type hxnDeviceType Read Only Watts, INTL / US, WDM / nonWDM,
SMF/MMF, MIMO / SISO)
Module
Info Firmware version hxnFirmwareVersion Read Only alpha numerical, XX.YY Firmware version

Module Info Product revision hxnProductRevision Read Only alpha numerical, XX.YY Product revision

Serial Number hxnSerialNumber Read Only 7 digit alpha-numerical s/n

hxnController Read Only 01-Sep

hxnConnector Read Only 1-16 Location index combined of :

Location index hxnController\hxnConnector\hxnOptmIx
hxnOptmIx Read Only 1-2 \hxnIx

hxnIx Read Only 1-4

link level hxnLinkLevel Read Only 0-255, raw reading

Laser And
Link status hxnLinkStatus Read Only Off / Low / Normal
Optics
optical adjustment status hxnOpticalAdjustStatus Read Only N/A, Fail, Success

.
Business Name Corning Restricted 45 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

– RF Parameters

.
Business Name Corning Restricted 46 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

Tab Function Name in MIB Behavior Field Content Notes

Service Control hxnServiceControl Read / Write On / Off

DL Max power hxnDLMaxPower Read / Write DL adjustment target

DL Power Input Level hxnDLPowerInputLevel Read Only

Adjustment result hxnAdjustmentResult Read Only Adjustment result - N/A, Fail, Success

Adjustment date and

hxnAdjustmentDateTime Read Only Last successful adjustment date and time
time

Do Adjust hxnDoAdjust PB
RF Parameters DL DCA Range (total, available for user to set
DL Attenuation hxnDLAttenuation Read / Write
from)

DL Output power hxnDLOutputPower Read Only Current output power of the remote

UL DCA Range (Total. Available for user to set

UL Attenuation hxnULAttenuation Read / Write
from)
UL Gain setting of the remote, Low, Normal,
UL Gain setting hxnULGainSetting Read / Write
High. Range

Reset hxnReset PB Perfrom soft reset to the unit

only for CMA useres ,TDD only, will

DL\UL\Auto mode to test signal and be able to
DL\UL test mode Read / Write remain in a status for 4 hours and return
ajust manualy for testing perfesess TDD only
to Auto

.
Business Name Corning Restricted 47 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

– Service Alarms

.
Business Name Corning Restricted 48 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

Tab Function Name in MIB Behavior Field Content Notes
Major Severity, ONLY FOR TDD
Sync Alarm hxnSyncAlarmSet Read Only checked / Unchecked via "alarm masking"
REMOTES
Notifiy Severity, ONLY FOR TDD
Sync Alarm hxnSyncAlarmClear Read Only checked / Unchecked via "alarm masking"
REMOTES

Service Off hxnServiceOffSet Read Only checked / Unchecked via "alarm masking" major severity

Service Off hxnServiceOffClear Read Only checked / Unchecked via "alarm masking" Notify severity

DL Output power High hxnOutputPowerHighSet Read Only checked / Unchecked via "alarm masking" minor severity

DL Output power High hxnOutputPowerHighClear Read Only checked / Unchecked via "alarm masking" Notify severity

DL Output power Low hxnOutputPowerLowSet Read Only checked / Unchecked via "alarm masking" major severity
Service Alarms
DL Output power Low hxnOutputPowerLowClear Read Only checked / Unchecked via "alarm masking" Notify severity

VSWR Alarm hxnVSWRAlarmSet Read Only checked / Unchecked via "alarm masking" major severity

VSWR Alarm hxnVSWRAlarmClear Read Only checked / Unchecked via "alarm masking" Notify severity

RF AdjustmentFail hxnAdjustmentFailSet Read Only checked / Unchecked via "alarm masking" Minor severity

RF AdjustmentFail hxnAdjustmentFailClear Read Only checked / Unchecked via "alarm masking" Notify severity

DL Protection activation hxnProtectionActivatedSet Read Only checked / Unchecked via "alarm masking" major severity

DL Protection activation hxnProtectionActivatedClear Read Only checked / Unchecked via "alarm masking" Notify severity

.
Business Name Corning Restricted 49 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

Tab Function Name in MIB Behavior Field Content Notes
accumulative for all the service
service 1 overall status hxnServiceOcerallStatus Read Only checked / Unchecked via "alarm masking" allarms(same indicator in GUI but different
severity)
Low Optical Link hxnLowOpticalLinkSet Read Only checked / Unchecked via "alarm masking" minor severity
Low Optical Link hxnLowOpticalLinkClear Read Only checked / Unchecked via "alarm masking" Notify severity
Temprature High hxnTemperatureHighSet Read Only checked / Unchecked via "alarm masking" minor severity
Temprature High hxnTemperatureHighClear Read Only checked / Unchecked via "alarm masking" Notify severity

Temperature protection hxnTemperatureProtectionSet Read Only checked / Unchecked via "alarm masking" major severity
Temperature protection hxnTemperatureProtectionClear Read Only checked / Unchecked via "alarm masking" Notify severity
Fans Minor hxnFansMinorFaultSet Read Only checked / Unchecked via "alarm masking" minor severity, for first fan alarm only
Fans Minor hxnFansMinorFaultClear Read Only checked / Unchecked via "alarm masking" minor severity, for first fan alarm only
Fans Major hxnFansMajorFaultSet Read Only checked / Unchecked via "alarm masking" major severity, For any other fan alarm
General Alarms major severity, For any other fan alarm
Fans Major hxnFansMajorFaultClear Read Only checked / Unchecked via "alarm masking" (same indicator in GUI but different
severity)
optical adjustment hxnOpticalAdjustSet Read Only checked / Unchecked via "alarm masking" minor Severity (not for WCS)
optical adjustment hxnOpticalAdjustClear Read Only checked / Unchecked via "alarm masking" Notify severity (not for WCS)
Door Open hxnDoorOpenAlarmSet Read Only checked / Unchecked via "alarm masking" minor severity

Door Open hxnDoorOpenAlarmClear Read Only checked / Unchecked via "alarm masking" Notify severity
Major Severity, ONLY FOR WCS
Remote Unit optical Link hxnRemoteUnitOpticalLinkSet Read Only checked / Unchecked via "alarm masking"
REMOTES
Notify severity, ONLY FOR WCS
Remote Unit optical Link hxnRemoteUnitOpticalLinkClear Read Only checked / Unchecked via "alarm masking"
REMOTES
Overall Status hxnOverallStatus Read Only
Change name to Alarm Masking
Alarm Masking hxnAlarmMask Read / Write Button
RH: change done

.
Business Name Corning Restricted 50 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

– Ext. Alarms

.
Business Name Corning Restricted 51 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

Tab Function Name in MIB Behavior Field Content Notes
External Alarm #1 hxnExternalAlarm1Set Read Only checked / Unchecked via "alarm masking" Severity depend on user setting TDD and WCS only
External Alarm #1 hxnExternalAlarm1Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
External Alarm #2 hxnExternalAlarm2Set Read Only checked / Unchecked via "alarm masking" Severity depend on user settingTDD and WCS only
External Alarms WCS External Alarm #2 hxnExternalAlarm2Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
and TDD only External Alarm #3 hxnExternalAlarm3Set Read Only checked / Unchecked via "alarm masking" Severity depend on user settingTDD and WCS only
External Alarm #3 hxnExternalAlarm3Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
External Alarm #4 hxnExternalAlarm4Set Read Only checked / Unchecked via "alarm masking" Severity depend on user settingTDD and WCS only
External Alarm #4 hxnExternalAlarm4Clear Read Only checked / Unchecked via "alarm masking" Notify severityTDD and WCS only
Led hxnExternalAlarmStatus1 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask1 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger1 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity1 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName1 Read / Write 20 chars, standard ASCII
chars)TDD and WCS only
Led hxnExternalAlarmStatus2 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask2 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger2 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity2 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName2 Read / Write 20 chars, standard ASCII
External Alarms WCS chars)TDD and WCS only
and TDD only Led hxnExternalAlarmStatus3 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask3 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger3 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity3 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName3 Read / Write 20 chars, standard ASCII
chars)TDD and WCS only
Led hxnExternalAlarmStatus4 Read Only Led color TDD and WCS only
check box hxnExternalAlarmMask4 Read / Write v mark, checked or uncheked TDD and WCS only
Trigger hxnExternalAlarmTrigger4 Read / Write N.O or N.C TDD and WCS only
Severity hxnExternalAlarmSeverity4 Read / Write Minor / Major / Notify TDD and WCS only
name for alarm set by external alarm (max of 20
Alarm Name hxnExternalAlarmName4 Read / Write 20 chars, standard ASCII
chars)TDD and WCS only

.
Business Name Corning Restricted 52 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

– TDD

.
Business Name Corning Restricted 53 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

Tab Function Name in MIB Behavior Field Content Notes

1 Channel frequency hxnTdd1ChannelFrequncy Read / Write L01-L39 or 2496.0-2690.0 TDD only, otheres NA

2 Channel frequency hxnTdd2ChannelFrequncy Read / Write L01-L39 or 2496.0-2690.1 TDD only, otheres NA

3 Channel frequency hxnTdd3ChannelFrequncy Read / Write L01-L39 or 2496.0-2690.2 TDD only, otheres NA

4 Channel frequency hxnTdd4ChannelFrequncy Read / Write L01-L39 or 2496.0-2690.3 TDD only, otheres NA

TDD parameters 5 Channel frequency hxnTdd5ChannelFrequncy Read / Write L01-L39 or 2496.0-2690.4 TDD only, otheres NA

6 Channel frequency hxnTdd6ChannelFrequncy Read / Write L01-L39 or 2496.0-2690.5 TDD only, otheres NA

UL\DL allocation mode hxnTddUlDlAllocationMode Read / Write 0-6 TDD only, otheres NA

Sub Frame Allocation hxnTddSubFrameAllocationMode Read / Write 0-9 (Normal), 0-7 (Extended) TDD only, otheres NA

Extended Sub Frame hxnTddSubFrameExtendedMode Read / Write 0-Normal 1-Extended TDD only, otheres NA

.
Business Name Corning Restricted 54 .
.
GUI Review

• SC-450 GUI review – HX-2.5GHz TDD

– Comment(N/A)

.
Business Name Corning Restricted 55 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD Engineering GUI review

1. Overview
This document is a manual for HX-WCS & HX-2.5GHz TDD GUI. It explains control sections and
describes matters requiring attention and how GUI is operated.

2. GUI Product Introduction

This Software was developed for the purpose of monitoring and controlling HX-WCS & HX-
2.5GHz TDD signal repeater and to download firmware updates.
Recommended operating system : Optimal for Window XP and Window 7
(Several functions may not work on other operating systems)

3. Operating GUI
A software that can monitor and control HX-WCS & HX-2.5GHz TDD using PC and serial
communication.
Serial Communication Cable: General D-Sub 9-pin Cable. (Not included)

.
Business Name Corning Restricted 56 .
.
GUI Review

• HX-WCS Engineering GUI review - 1

• Run ‘HX_WCS.exe’ from the extracted folder.

• Select connection port (Only shows connectable COM Port)
• From device manager, check the currently connected COM Port.
• Press Connect Button to connect communication port.

.
Business Name Corning Restricted 57 .
.
GUI Review

• HX-WCS Engineering GUI review - 2

1. RS232 Communication : D-sub 9 pin (in HX-WCS)

2. UDP Communication : Ethernet Port (in HX-WCS)
3. BU Tunneling Communication : D-sub 9pin (in BU)

.
Business Name Corning Restricted 58 .
.
GUI Review

• HX-WCS Engineering GUI review - 3

• GUI Tab - SYSTEM

.
Business Name Corning Restricted 59 .
.
GUI Review

• HX-WCS Engineering GUI review - 4

Items Detail Sub-items Related to LEN Order Displayed as
Module Type 0 1 "HX-WCS"
Device Type S 1 1 2W/US/(SISO or MIMO)
Site ID S,C 20 2 ASCII (20 characters)
SUB Site ID S,C 2 22 2byte Hex Decimal S : Status
Serial Number S,C 4 24 4byte Hex Decimal
Band Number S 1 28 "23"
C : Control
Name S,C 20 29 ASCII (20 characters)
General
Information Add on value per 30min.
Life Time Counter S,C 4 49
ex) 24.5 hour
Add on value per 1sec.
Device Up Time S,C 4 53
ex) 1h 2m 4s
Up to three-digit decimal point
12V Monitoring S 2 57
ex) 12.xxx
Up to three-digit decimal point
28V Monitoring S 2 59
ex) 28.xxx
System
Temperature Compensation On/Off S,C 1 61 ON/OFF
Active Temperature S 2 62 Unit:℃ ex) 25℃
Delta Temperature ATT S 1 64
Temperature
Over Temp. Protection Threshold S,C 1 65 ex) 80
Over Temp. Alarm Threshold S,C 1 66 ex) 70
Over Temp Protection On/Off S,C 1 67 ON/OFF
Active/Inactive Version
ex) 0x2021 = 2.0.2.1/2.0.2.1
Active / Inactive SW Version S 2 68
20 - Major Version
Version 21 - Minor Version
Information
Product Revision S 2 70 ex) A.00
H/W Revision S 1 72 ex) 1.0
Swap F/W C 1 73 Version Change
Service
Service Control S,C 1 74 ON/OFF
Information
.
Business Name Corning Restricted 60 .
.
GUI Review

• HX-WCS Engineering GUI review - 5

Related
Items Detail Sub-items LEN Order Displayed as
to
Service Alarm Status
Service Alarm S 1 75
Normal : Green, Alarm : Red
Alarm General Alarm Status
General Alarm S 1 76
Summary Normal : Green, Alarm : Red
Overall Alarm Status
Overall Alarm 0 77
Normal : Green, Alarm : Red
IP Address S,C 4 77 ex)192.168.1.5 S : Status
Network Subnet Mask S,C 4 81 ex)255.255.255.0
Communication Gateway S,C 4 85 ex)192.168.1.254
C : Control
Mac Address S,C 6 89 ex)12-34-56-78-90
FAN Speed S,C 1 95 OFF / Normal / High
Good (No Alarm)
Fan
FAN Status S 1 96 Minor(one Alarm)
Information
System Major(more than 2)
FAN Alarm S 1 97 Normal : Green, Alarm : Red
WCS FSK Tx Counter S 4 98 WCS -> BU
WCS FSK Rx Counter S 4 102 WCS <- BU
RU FSK Tx Counter S 4 106 WCS -> RU
RU FSK Rx Counter S 4 110 WCS <- RU
FSK
FSK RSSI S 1 114
Information
RU FSK RSSI S 1 115
WCS FSK Tx Level S,C 1 116
RU Tx Level S,C 1 117
RU Serial Number S 4 118
FSK GUI Debug S,C 1 122 ON/OFF
Factory /
RU FSK GUI Debug S,C 1 123 ON/OFF
FSK Debug
Factory Setting C 1 124
.
Business Name Corning Restricted 61 .
.
GUI Review

• HX-WCS Engineering GUI review - 6

• GUI Tab – ALARM/OPTIC/HPA

.
Business Name Corning Restricted 62 .
.
GUI Review

• HX-WCS Engineering GUI review - 7

Items Detail Sub-items Related to LEN Order Displayed as

Normal : Green, Alarm : Red

Service : raised(Service Status is OFF)
Over Power : raised(> Max Out Power + 2), cleared(< Max Out Power)
DL Protection : raised(> Max Out Power + 3), cleared(< Max Out Power)
Service Alarm S 1 1
Low Power : raised(< Max Out Power - 20), cleared(> Max Out Power - 18)
Service Status RF Adjust : raised(Adjust Fail)
DL/UL Limiter : raised(Limiter≠0), cleared(Limiter=0)
VSWR : raised(≥ 5:1), cleared(< 5:1)

Service Alarm Mask S,C 1 5 Uncheck : Mask, Check : Unmask

Overall Service Alarm S 1 2 Normal : Green, Alarm : Red

Normal : Green, Alarm : Red

Over Temp. : raised (> Max Temp), cleared(< Max Temp. - 5)
Over Temp. Protection : raised (> Max Temp + 10), cleared(< Max Temp. - 5)
General Alarm S 1 3 HE/RU Optical Link : raised(Low & OFF), cleared(Normal)
General Status Fan Minor, Fan Major : Ref. fan operation
Door : raised(open), cleared(closed)
Service Overall Status : depend on Service

Overall General Alarm S 1 4 Normal, Minor, Major

General Alarm Mask

HE Rx Link Status
S,C

S
1

1
6

7
Uncheck : Mask, Check : Unmask
The number is PDI value
OFF : 0-35, Low : 36-100, Normal : 101-255
S : Status
Alarm
Optic
WCS Optic
HE Fiber Mode
HE Optic Rx Link Level
S
S
1
2
8
9
Non WDM / SMF / SISO or MIMO
dBm/Raw C : Control
Information HE Optic Tx Power S 1 11 unit : 0.5dBo
HPA
HE Optic Loss S 1 12 unit : 0.5dB
HE Optic Adjust ATT S 1 13 unit : 0.5dB
RU Optic Adjust ATT S 1 14 unit : 0.5dB
The number is PDI value
RU Rx Link Status S 1 15
OFF : 0-35, Low : 36-100, Normal : 101-255
Remote Optic
RU Optic Rx Link Level S 2 16 dBm/Raw
Information
RU Optic Tx Power S 1 18 unit : 0.5dBo
RU Optic Loss S 1 19 unit : 0.5dB
Return Loss S 2 20
VSWR S 2 22
Return Loss Threshold S,C 2 24
HPA VSWR Threshold S,C 2 26
Information
VSWR Alarm Check Mode S,C 1 28 Return Loss
Unknown, High Temperature, VSWR, Over Power, DC Fail, User,
HPA Off Reason S 1 29
Over Power, Device Fail

Etc. Alarm S 1 30 Optic Adjust, Module Insert, Optic Module Link, HPA Module Link
Uncheck : Mask, Check : Unmask
External Alarm & Mask S 2 31
Normal : Green, Alarm : Red
Etc. Status Severity : Notification, Minor, Major
Alarm External Alarm Severity, Trigger Level S,C 2 33
Trigger Level : N.C, N.O
Optic Reset C 1
HPA Reset C 1
Optic Adjust C 1 Optic Adjust Value
.
Business Name Corning Restricted 63 .
.
GUI Review

• HX-WCS Engineering GUI review - 8

• GUI Tab – ALARM/OPTIC/HPA

.
Business Name Corning Restricted 64 .
.
GUI Review

• HX-WCS Engineering GUI review - 9

Items Detail Sub-items Related to LEN Order Displayed as

DL Input Power(RMS) S 2 1 "LOW" : < -72dBm

DL PWR
DL Output Power (RMS)
DL Output Power (Peak)
S
S
2
2
3
5
"LOW" : < -2dBm
"LOW" : < -2dBm
S : Status
Information
HPA On/Off
Output Power Mode
S,C
S,C
1
1
7
8
ON / OFF
Average, Peak
C : Control
DL Operation DCA S 1 9 unit : 0.5dB
DL Manual DCA S,C 1 10 unit : 0.5dB
DL Att
DL Factory DCA S,C 1 11 unit : 0.5dB
Information
DL Limiter DCA S 1 12 unit : 0.5dB
DL Restore Factory C 1

DL ALC DL Limiter On/Off S,C 1 13 ON / OFF

Information DL Limiter Status S 1 14 Disable / Enable / Active(Limiter is running)
DL Max Output Power S,C 1 15 range : +19 - +34dBm

DL Th. DL Output High Threshold S,C 1 16 Max Output Power + 2

Information DL Output Low Threshold S,C 1 17 Max Output Power - 20
DL Output Protection Threshold S,C 1 18 Max Output Power + 3

UL PWR UL Input Power (RMS) S 2 19 "LOW" : < -55dBm

Information UL Output Power (RMS) S 2 21 "LOW" : < -40dBm
DL Path UL Operation DCA S 1 23 unit : 0.5dB
UL Path UL Manual DCA S,C 1 24 unit : 0.5dB

UL Att UL Factory DCA S,C 1 25 unit : 0.5dB

Information UL Limiter DCA S 1 26 unit : 0.5dB
UL Gain Set S,C 1 27 High : 41dB, Normal : 31dB, Low : 21dB
UL Restore Factory C 1

UL ALC UL Limiter On/Off S,C 1 28 ON / OFF

Information UL Limiter Status S 1 29 Disable / Enable / Active(Limiter is running)
DL RF Adjustment DCA S 1 30 unit : 0.5dB
Adjustment DATE S 3 31 Adjustment Success Date
RF Adj. Adjustment Time S 3 34 Adjustment Success Time
Information DL RF Adjustment Result S 1 37 Success, Fail(Low power),Fail(Over power),In Progress
Start adjustment
DL Do Adjustment C 7
(include YY/MM/DD hh:mm:ss, DL Output Max Power)
RU DL Gain S,C 1 38
RU UL Gain S,C 1 39

Gain Ext. DL Gain S,C 1 40

Information Ext. UL Gain S,C 1 41
DL Extension On/Off S,C 1 42 ON / OFF
UL Extension On/Off S,C 1 43 ON / OFF
.
Business Name Corning Restricted 65 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 1

• Run ‘HX_Spark.exe’ from the extracted folder.

• Select connection port (Only shows connectable COM Port)
• From device manager, check the currently connected COM Port.
• Press Connect Button to connect communication port.

.
Business Name Corning Restricted 66 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 2

1. RS232 Communication : D-sub 9 pin (in HX-2.5GHz TDD)

2. UDP Communication : Ethernet Port (in HX-2.5GHz TDD)
3. OCH Tunneling Communication : D-sub 9pin (in OCH)

.
Business Name Corning Restricted 67 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 3

• GUI Tab - SYSTEM

.
Business Name Corning Restricted 68 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 4

Items Detail Sub-items Related to LEN Order Displayed as
Module Type 0 1 "HX-Spark"
Device Type S 1 1 2W / US / SISO or MIMO
Site ID
SUB Site ID
S,C
S,C
20
2
2
22
ASCII (20 characters)
2byte Hex Decimal
S : Status
Serial Number
Band Number
Name
S,C
S
S,C
4
1
20
24
28
29
4byte Hex Decimal
"25"
ASCII (20 characters)
C : Control
General
Information Add on value per 30min.
Life Time Counter S,C 4 49
ex) 24.5 hour
Add on value per 1sec.
Device Up Time S,C 4 53
ex) 1h 2m 4s
Up to three-digit decimal point
12V Monitoring S 2 57
ex) 12.xxx
Up to three-digit decimal point
28V Monitoring S 2 59
ex) 28.xxx
Temperature Compensation On/Off S,C 1 61 ON/OFF
Active Temperature S 2 62 Unit:℃ ex) 25℃
Delta Temperature ATT S 1 64
Temperature
Over Temp. Protection Threshold S,C 1 65 ex) 80
Over Temp. Alarm Threshold S,C 1 66 ex) 70
Over Temp Protection On/Off S,C 1 67 ON/OFF
Active/Inactive Version
ex) 0x2021 = 2.0.2.1/2.0.2.1
Active / Inactive SW Version S 2 68
20 - Major Version
Version 21 - Minor Version
Information
System Product Revision S 2 70 ex) A.00
H/W Revision S 1 72 ex) 1.0
Swap F/W C 1 73 Change the Version
Service
Service Control S,C 1 74 ON/OFF
Information
Service Alarm Status
Service Alarm S 1 75
Normal : Green, Alarm : Red
General Alarm Status
Alarm Summary General Alarm S 1 76
Normal : Green, Alarm : Red
Overall Alarm Status
Overall Alarm 0 77
Normal : Green, Alarm : Red
IP Address S,C 4 77 ex)192.168.1.5
Network Subnet Mask S,C 4 81 ex)255.255.255.0
Communication Gateway S,C 4 85 ex)192.168.1.254
Mac Address S,C 6 89 ex)12-34-56-78-90
FAN Speed S,C 1 95 OFF / Normal / High
Good (No Alarm)
Fan
FAN Status S 1 96 Minor(one Alarm)
Information
Major(more than 2)
FAN Alarm S 1 97 Normal : Green, Alarm : Red
FSK Tx Counter S 4 98 Spark -> OCH
FSK Rx Counter S 4 102 Spark <- OCH
FSK
FSK RSSI S 1 106 Voltage
Information
FSK Tx Level S,C 1 107 dBm
RU Serial Number S 4 108
Factory Set Factory Setting C 1 112

.
Business Name Corning Restricted 69 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 5

• GUI Tab – ALARM/OPTIC/HPA

.
Business Name Corning Restricted 70 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 6

Items Detail Sub-items Related to LEN Order Displayed as

Normal : Green, Alarm : Red

Service : raised(Service Status is OFF)
Over Power : raised(> Max Out Power + 2), cleared(< Max Out Power)
DL Protection : raised(> Max Out Power + 3), cleared(< Max Out Power)
Service Alarm S 1 1
Low Power : raised(< Max Out Power - 20), cleared(> Max Out Power - 18)
Service Status RF Adjust : raised(Adjust Fail)
DL/UL Limiter : raised(Limiter≠0), cleared(Limiter=0)
VSWR : raised(≥ 5:1), cleared(< 5:1)

Service Alarm Mask S,C 1 5 Uncheck : Mask, Check : Unmask

Overall Service Alarm S 1 2 Normal : Green, Alarm : Red

Normal : Green, Alarm : Red

Over Temp. : raised (> Max Temp), cleared(< Max Temp. - 5)
Over Temp. Protection : raised (> Max Temp + 10), cleared(< Max Temp. - 5)
General Alarm S 1 3 HE/RU Optical Link : raised(Low & OFF), cleared(Normal)
General Status Fan Minor, Fan Major : Ref. fan operation
Door : raised(open), cleared(closed)
Service Overall Status : depend on Service

Overall General Alarm S 1 4 Normal, Minor, Major

General Alarm Mask

HE Rx Link Status
S,C

S
1

1
6

7
Uncheck : Mask, Check : Unmask
The number is PDI value S : Status
OFF : 0-35, Low : 36-100, Normal : 101-255

Alarm WCS Optic

HE Fiber Mode
HE Optic Rx Link Level
S
S
1
2
8
9
Non WDM / SMF / SISO or MIMO
dBm/Raw
C : Control
Optic Information HE Optic Tx Power S 1 11 unit : 0.5dBo
HPA
HE Optic Loss S 1 12 unit : 0.5dB
HE Optic Adjust ATT S 1 13 unit : 0.5dB
RU Optic Adjust ATT S 1 14 unit : 0.5dB
The number is PDI value
RU Rx Link Status S 1 15
OFF : 0-35, Low : 36-100, Normal : 101-255
Remote Optic
RU Optic Rx Link Level S 2 16 dBm/Raw
Information
RU Optic Tx Power S 1 18 unit : 0.5dBo
RU Optic Loss S 1 19 unit : 0.5dB
Return Loss S 2 20
VSWR S 2 22
Return Loss Threshold S,C 2 24
HPA VSWR Threshold S,C 2 26
Information
VSWR Alarm Check Mode S,C 1 28 Return Loss
Unknown, High Temperature, VSWR, Over Power, DC Fail, User,
HPA Off Reason S 1 29
Over Power, Device Fail

Etc. Alarm S 1 30 Optic Adjust, Module Insert, Optic Module Link, HPA Module Link
Uncheck : Mask, Check : Unmask
External Alarm & Mask S 2 31
Normal : Green, Alarm : Red
Etc. Status Severity : Notification, Minor, Major
Alarm External Alarm Severity, Trigger Level S,C 2 33
Trigger Level : N.C, N.O
Optic Reset C 1
HPA Reset C 1
Optic Adjust C 1 Optic Adjust Value
.
Business Name Corning Restricted 71 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 7

• GUI Tab – DL Path / UL Path

.
Business Name Corning Restricted 72 .
.
GUI Review

• HX-2.5GHz TDD Engineering GUI review - 8

Items Detail Sub-items Related to LEN Order Displayed as
DL Input Power(RMS) S 2 1 "LOW" : < -72dBm

DL PWR
Information
DL Output Power (RMS)
DL Output Power (Peak)
S
S
2
2
3
5
"LOW" : < -5dBm
"LOW" : < -5dBm S : Status
HPA On/Off S,C 1 7 ON /OFF
Output Power Mode
DL Operation DCA
S,C
S
1
1
8
9
Average, Peak
unit : 0.5dB
C : Control
DL Manual DCA S,C 1 10 unit : 0.5dB
DL Att
DL Factory DCA S,C 1 11 unit : 0.5dB
Information
DL Limiter DCA S 1 12 unit : 0.5dB
DL Restore Factory C 1
DL ALC DL Limiter On/Off S,C 1 13 ON / OFF
Information DL Limiter Status S 1 14 Disable / Enable / Active(Limiter is running)
DL Max Output Power S,C 1 15 range : +19 - +34dBm
DL Th. DL Output High Threshold S,C 1 16 Max Output Power + 2
Information DL Output Low Threshold S,C 1 17 Max Output Power - 20
DL Output Protection Threshold S,C 1 18 Max Output Power + 3
UL PWR UL Input Power (RMS) S 2 19 "LOW" : < -55dBm
Information UL Output Power (RMS) S 2 21 "LOW" : < -40dBm
UL Operation DCA S 1 23 unit : 0.5dB
UL Manual DCA S,C 1 24 unit : 0.5dB
UL Att UL Factory DCA S,C 1 25 unit : 0.5dB
Information UL Limiter DCA S 1 26 unit : 0.5dB
DL Path UL Gain Set S,C 1 27 High : 41dB, Normal : 31dB, Low : 21dB
UL Path
UL Restore Factory C 1
UL ALC UL Limiter On/Off S,C 1 28 ON / OFF
Information UL Limiter Status S 1 29 Disable / Enable / Active(Limiter is running)
DL RF Adjustment DCA S 1 30 unit : 0.5dB
Adjustment DATE S 3 31 Adjustment Success Date
RF Adj. Adjustment Time S 3 34 Adjustment Success Time
Information DL RF Adjustment Result S 1 37 Success, Fail(Low power),Fail(Over power),In Progress
Start adjustment
DL Do Adjustment C 7
(include YY/MM/DD hh:mm:ss, DL Output Max Power)
Ext. DL Gain S,C 1 38
Gain Ext. UL Gain S,C 1 39
Information DL Extension On/Off S,C 1 40 ON / OFF
UL Extension On/Off S,C 1 41 ON / OFF
T Sync Frequency Set 12 42 val *0.1 (100kHz)
Freq. Info. Operation Frequency 2 54 val *0.1 (100kHz)
Switch Mode 1 56 Auto, DL Only, UL Only, OFF
UL/DL Config 1 57 Config Num #0 ~ #6
SSF Config 1 58 if normal CP : #0 ~ #9, if extended CP : #0 ~ #7
T Sync CP Type 1 59 Normal CP(default), Extended CP
Information
DL/UL Gap 2 60
Sync Operation Mode S,C 1 62 PSS Sync Signal(default)
PSS Threshold S,C 2 63 default : 0x50
.
Business Name Corning Restricted 73 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD GUI Download Sequence -1

Activate Download
Window

• Single firmware can be downloaded through SC-450 Web GUI to RCU/OPTIC/HPA at a time.
(Except, SISO/MIMO is classified)
• But, downloading through Eng. GUI is separately done for each module(RCU/OPTIC/HPA).
(Download the update-required module only)
.
Business Name Corning Restricted 74 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD GUI Download Sequence -2

• Download window

Select each module to download

Module Type : RCU, SISO_OPTIC, SISO_HPA,
MIMO_OPTIC, MIMO_HPA, SYNC_CPU, SYNC_FPGA

Click then Select

.
Business Name Corning Restricted 75 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD GUI Download Sequence -3

• Download window

Click

Select module extension

File Select for Download

RCU : *.WCS (HX-WCS)
*.SPK (HX-2.5GHz TDD)
Download Start Optic : *.OPT
HPA : *.HPA
Sync CPU: *.SCU
Sync FPGA: *.SFA (Local only)
.
Business Name Corning Restricted 76 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD GUI Download Sequence -4

• Download window

Download

After download, reset only relevant modules

Except, running Swap after download enables
RCU Firmware to reset.

.
Business Name Corning Restricted 77 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD GUI Download Sequence -5

• Click the Swap button for RCU Firmware update.
– Active/Inactive version is switched over and RCU is reset.

RCU version
information change check
Swap RCU Firmware.

.
Business Name Corning Restricted 78 .
.
GUI Review

• HX-WCS & HX-2.5GHz TDD Engineering GUI – Extra Features

System Reset

.
Business Name Corning Restricted 79 .
.
Typical Field Issues
Initial Value
No Alarm Detail Corrective Actions
WCS 2.5-TDD
1) Alarm on: Service alarm on due to shutdown
- Check 4 alarms(OverTemp Protection, DL Protection
algorithm (OverTemp Protection,
1 Service and VSWR, TDD Sync) and follow its corrective actions
DL Protection, VSWR, TDD Sync)
2) Alarm off: shutdown condition cleared
1) Alarm on : DL Output Power > Max output
power+ 2dB - After checking output, adjust the output(control Manual Max output power
2 DL Output High
2) Alarm off : DL Output Power < Max output Atten or redo RF Adjustment) = 33dBm
power (Hysteresis 2dB)
- Check connection of Optic Cable
1) Alarm on : RF Power < Max output power-20dB Max output power
: (GUI) Optic Rx level, Optic Link Alarm etc.
3 DL Output Low 2) Alarm off : RF Power > Max output power-18dB = 33dBm
- Check RF Input Level
(Hysteresis 2dB)
- Check attenuator settings (Adjust Att, Manual DCA)
- Connect output terminal (ANT) High Power Term and
1) Alarm on : VSWR > VALUE (VSWR Threshold) check if alarm is off
VSWR threshold =
4 VSWR 2) Alarm off : Measured VSWR < VALUE (VSWR - Check antenna connection and VSWR of the antenna
2:1(RL: 8.5dB)
Threshold) - Check for foreign substance on output terminal
connector and connection cable
- Check Optic Cable connection: Check if Fiber Optical
1) Alarm on : DL RF Adjustment = Fail loss is within standard range of the device.
a) Despite ATT is operating, Over Power or Under → Loss: 4dBo(HX-WCS), 6dBo(HX-2.5GHz TDD).
RF Adjustment power - Check RF connection : While performing adjustment,
5
Fail b) When failed, ATT restores default or previous check if calibration signal of RU(GUI: DL Input Power) is
value. detected on optimal level.
2) Alarm off : DL RF Adjustment = Success / NA → Reference level : -48.5dBm(HX-WCS), -40dBm
(HX2.5GHz TDD) @ 0dBo
.
Business Name Corning Restricted 80 .
.
Typical Field Issues
Initial Value
No Alarm Detail Corrective Actions
WCS 2.5-TDD
1) Alarm on: RF Power > Max output power + 3dB
- Occurs when: RF Power > DL Protection Threshold.
- Check if Max output Power and DL Limiter is
2) Alarm off Max output power
6 DL Protection working correctly.
a) RF Power < Max output power - 3dB = 33dBm
- Check RF Input Level.
b) Recheck alarm after alarm is turned off if user
control is ON
- Check RF Input Level.
- Check TDD Parameter.
→ Check if DL/UL Configuration information is
TDD Sync 1) Alarm on : TDD Sync failed
7 identical to base station and whether SSF is
(HX-2.5GHz TDD Only) 2) Alarm off : TDD Sync success
being transmitted or not.
→ Check if frequency information is similar to
base station signal.
1) Alarm on : Limiter function on,
- Check Output Max Power and RF input/output Max output power
8 DL Limiter DL Output Power > Max output power
level. = 33dBm
2) Alarm off : DL Output Power < Max output power

1) Alarm on : Limiter function on, High = -50dBm

UL Input Power > UL Limiter Threshold Normal = -40dBm
9 UL Limiter - Check UL input level and UL Gain.
- For Normal Gain, -40dBm Low = -30dBm
2) Alarm off : UL Input Power < UL Limiter Threshold

.
Business Name Corning Restricted 81 .
.
Typical Field Issues
Initial Value
No Alarm Detail Corrective Actions
WCS 2.5-TDD
- Check optic cable connection:
1) Alarm on: PD Detector value is lower than
Check if Fiber Optical loss is within device’s standard
standard
range.
10 (HE) Optical link → HX-WCS(-5dBm), HX-2.5GHz TDD(-7dBm)
→ Loss: 4dBo(HX-WCS), 6dBo(HX-2.5GHz TDD).
2) Alarm off : PD Detector value is within standard
- Check the cleanliness of optic cable and module
range
- Check the bending/sheath of optic cable
1) Alarm on: Temperature > OverTemp Alarm
Threshold
2) Alarm off : Temperature < OverTemp Alarm - Check OverTemp alarm threshold value. OverTemp Alarm
11 Over Temperature
Threshold – 5 degrees (Hysteresis 5℃) - Check FAN alarm and operating status. Threshold = 75℃
3) Temperature = Base on temperature indicated on
GUI’s Main System
1) Alarm on : Temperature > OverTemp Protection
Threshold
OverTemp
Over Temperature 2) Alarm off : Temperature < OverTemp Protection - Check OverTemp Protection threshold value.
12 Protection
Protection Threshold – 15 degrees (Hysteresis 15℃) - Check FAN alarm and operating status.
Threshold = 85℃
3) Temperature = Base on temperature indicated on
GUI’s Main System
- Visually inspect the condition of relevant FAN and
1) Alarm on : FAN stop working.(5 seconds or more)
FAN-Tray (foreign substance, outside interference, etc.)
a) Minor alarm : First FAN warning (Yellow)
- Check FAN Cable connection and FAN input power
b) Major alarm : More than one FAN warning (Red)
13 FAN Alarm - Connect the power switch of problematic FAN to
2) Alarm off : Alarm turns off if FAN works normally
normal working FAN port and check if it’s the FAN itself
3) User control On/off function implemented and
that’s not working.
status saved.
- Exchange FAN
.
Business Name Corning Restricted 82 .
.
Typical Field Issues
Initial Value
No Alarm Detail Corrective Actions
WCS 2.5-TDD
1) Alarm on : When PD Detector value is lower than
- Check the connection of optic cable.
standard value
- Check the LD Level of 2nd hop remote (ex.HX4)
RU Optical link → HX-WCS(-5dBm)
14 connected to RU.
(HX-WCS Only) 2) Alarm off : PD Detector value is within standard
- Check the cleanliness of optic cable and module
range
- Check the bending/sheath of optic cable

1) Alarm on : When door is opened

15 Door - Check Door Switch and cable connection.
2) Alarm off : When door is closed
1) Alarm on
- When at least one alarm is raised from between
item 10 ~ 15.
- Detect only UnMasked alarms.
16 Overall status General
But each alarms are displayed.
2) Alarm off
- When all General Status’ alarms are disabled.
- Detect only UnMasked alarm.
1) Alarm on
→ When alarm is raised for either Overall Status
Total Overall Alarm Service or Overall Status General
17
(GUI SYSTEM Tap) 2) Alarm off
→ When alarms are disabled for both Overall Status
Service and Overall Status General

Exchange the HX-Module if alarm is still raised after corrective actions are performed.

Exchange the Chassis if alarms is still raised after HX-Module is exchanged.
.
Business Name Corning Restricted 83 .
.
Default Value GUI – WCS(SYSTEM Tap)

.
Business Name Corning Restricted 84 .
.
Default Value GUI - WCS(ALARM/OPTIC/HPA Tap)

.
Business Name Corning Restricted 85 .
.
Default Value GUI - WCS(DL Path / UL Path Tap)

.
Business Name Corning Restricted 86 .
.
Default Value GUI – 2.5GHz TDD(SYSTEM Tap)

.
Business Name Corning Restricted 87 .
.
Default Value GUI – 2.5GHz TDD(ALARM/OPTIC/HPA Tap)

.
Business Name Corning Restricted 88 .
.
Default Value GUI – 2.5GHz TDD(DL Path / UL Path Tap)

.
Business Name Corning Restricted 89 .
.
Power Connection

• Step by step guidelines

– Note: The internal power connections and other connections should
already be connected.
1. Make sure power source switch is OFF!
2. Open cabinet door, if not already open, to access Power supply
Unit (PSU).

- HX WCS PSU DC Connector - HX-2.5GHz TDD PSU DC Connector

.
Business Name Corning Restricted 90 .
.
Power Connection

• Step by step guidelines

3. Connect the DC wires leading from the power source to the Dinkle
2ESDFM terminal block plug according to indicated pin out on the
PSU DC terminal block:
• Identify the positive and negative terminals on power source feed
positions. The wiring sequence is positive to positive and negative to
negative.
• Open the terminal block screw and insert appropriate feed into the
terminal block plug
• Torque the terminal block captive screw (above the installed wire lead),
using a ratcheting torque screwdriver.
• Recommended torque is 0.49N•m.
• Repeat above steps for all feeds
• Insert the plug into the PSU DC terminal block.

.
Business Name Corning Restricted 91 .
.
Power Connection

• Power Consumption by equipment

WCS 2.5GHz-TDD
Item MIMO MIMO Remark
SISO MIMO SISO MIMO
(SISO Service) (SISO Service)
Rated Output
44W 66W 76W 69W 115W 120W 33dBm
Power
Max Output Power 46W 68W 81W 73W 118W 125W 34dBm

– Maximum input Power Consumption of Dinkle Connector of Input power terminal of PSU by Pair is
62W.
– When Max Output power, WCS is recommended to connect minimum of 2 pairs, and 2.5GHz-TDD
is recommended to connect minimum of 3 pairs in consideration of power consumption.

• Which AWG wires are recommended

– Compatible wire size for plug : 30 ~ 12 AWG
– No. of required pairs
• Minimum of two pairs (up to three) for HX-WCS
• Minimum of three pairs (up to four) for HX-2.5GHz TDD
– Max current consumption for connector: for 20 AWG = 4.5A; (max. 5A)

.
Business Name Corning Restricted 92 .
.
Power Connection

• Outline of Dinkle connectors (2ESDFM)

.
Business Name Corning Restricted 93 .
.
 RF Adjustment – SC-450 Web GUI
• RF Adjustment by CW signal – 2.5GHz TDD

②
①
④ ⑤
③

1. Check if ‘① DL Pin Level’ of GUI is in the normal range of -52dBm to -40dBm.

2. Set the value in ‘②DL Output Max Power’.(21dBm ~ 33dBm)
3. Click ‘③Adjust’ and it automatically carries out RF Adjustment. (In case of HX-2.5GHz TDD, when
clicked ‘DL Do Adjust’ it is set to carry out ⑤‘Downlink’ and ‘HPA On’ by internal algorithm.)

.
Business Name Corning Restricted 94 .
.
 RF Adjustment – SC-450 Web GUI
• RF Adjustment by CW signal – 2.5GHz TDD

②
①
④ ⑤
③

4. After completion of RF Adjustment, check if ‘④Adjust Result’ is “Success(Done)”. If “Success(Done)”

then, ‘Adjust Date/Time’ will be updated to the latest time of “Success(Done)”.
5. Then ⑤Switch Mode will get back to “Auto”. Since input signal is CW signal, TDD Sync alarm
would occur making HPA OFF. (In case that input signal is normal TDD signal, output power is
being maintained after RF Adjustment.) .
Business Name Corning Restricted 95 .
.
 RF Adjustment – SC-450 Web GUI
• RF Adjustment by CW signal – 2.5GHz TDD

②
①
④ ⑤
③

6. In order to check if RF Adjustment is normally performed, set ‘⑤Switch Mode’ as “Downlink” and
check ‘DL Output Power’. Then, set ‘⑤Switch Mode’ back to “AUTO”.
※ In terms of BTSC, some functions as like frequency and attenuator setting and so on are limited.

.
Business Name Corning Restricted 96 .
.
 RF Adjustment – HX-2.5GHz TDD GUI
• RF Adjustment by CW signal – 2.5GHz TDD

⑥
④
③

.
Business Name Corning Restricted 97 .
.
 RF Adjustment – HX-2.5GHz TDD GUI
• RF Adjustment by CW signal – 2.5GHz TDD
1. Check if ‘① DL Input Power Level’ of GUI is in the normal range of -52dBm to -40dBm.
2. Set the value in ‘②DL Output Max Power’.(19dBm ~ 34dBm)
3. Click ‘③DL Do Adjust’ and it automatically carries out RF Adjustment. (In case of HX-2.5GHz TDD,
when clicked ‘DL Do Adjust’ it is set to carry out ‘DL only’ and ‘HPA On’ by internal algorithm.)
4. After completion of RF Adjustment, check if ‘④Status’ is “Success”. If “Success” then, ‘Date and
Time’ will be updated to the latest time of “Success”.
5. Then ⑤Switch Mode will get back to “Auto”. Since input signal is CW signal, TDD Sync alarm
would occur making HPA OFF. (In case that input signal is normal TDD signal, output power is
being kept after RF Adjustment.)
6. In order to check if RF Adjustment is normally performed, set ‘④ Switch Mode’ as “DL Only” and
‘⑥HPA On/Off’ as “On” and check ‘DL Output Power’. Then, set ‘④Switch Mode’ back to “AUTO”.

.
Business Name Corning Restricted 98 .
.
 LTE TDD UL/DL Configuration

Uplink-Downlink Allocations

99 Business Name Corning Restricted 99 .

.
 LTE TDD UL/DL Configuration

10 Business Name Corning Restricted 100 .

.

0
 Module Replacement
• Step by step instructions on module replacements
1. Fan replacement
1) Open cabinet door, if not already open, to access the fan interface cover at the
door.
2) Open the fan interface cover in the middle of door.
3) Disconnect the cable of the fan being replaced and separate it from the door.
4) Attach new FAN(including finger guide) to the Door and connect the cable.
5) Check if FAN is working properly.

FAN 1

FAN 2

FAN 3

FAN 4

FAN interface cover

.
Business Name Corning Restricted 101 .
.
Module Replacement

• Step by step instructions on module replacements

2. Module replacement
1) Module replacement only applies to HX-Module.
• PSU, Cavity filter, RCU replacement has to be done at chassis level.
2) Disconnect optic cable from HX-Module.
• Check the location of replacing HX-Module: SISO(right), MIMO(left)
• Only one optic cable is connected to HX-2.5GHz TDD module but since HX-WCS has
several Optic cables, try to label the cables accordingly.
3) Use captive screws and ejector to detach HX-Module from chassis. (Toolless)
4) Insert new HX-Module to chassis and fasten ejector and captive screws.
5) Check if power is being supplied via HX-Module’s “RUN” LED .
6) Connect optic cable to the relevant optic port. (Make sure to connect cables to
correct ports for HX-WCS.)
7) Check if Link “LED” (Link status: normal) is on. In case of HX-WCS, LED is
separated into Donor(BU) and Remote(HX4 or MA1K/2K).

.
Business Name Corning Restricted 102 .
.
Module Replacement

• Step by step instructions on module replacements

2. Module replacement
8) After checking the connection of HX-Module, proceed with initial set-up
procedure.
– Donor
• Perform Discovery procedure of new HX-Module.
• Check if the communication is normal for new HX-Module.(Message Counters)
– Remote
• Perform fiber optics loss compensation with Optical adjustment.
• Set Max output power and perform RF Adjustment: Check if output is normal.
• Insert Module information of existing HX-Module (ex.: UL Gain, T Sync
Information, etc.)
– SC-450: Insert Module Information of existing HX-Module (ex.: Site ID, etc.)

.
Business Name Corning Restricted 103 .
.
Connection Guidance on EPM with 2K’s

• Pictures of each sections of modules and label – EPM

– External Passive Module

.
Business Name Corning Restricted 104 .
.
Connection Guidance on EPM with 2K’s

• Pictures of each sections of modules and label – EPM

Marketing Label

Label (Position)

.
Business Name Corning Restricted 105 .
.
Connection Guidance on EPM with 2K’s

• Functions of each ports – EPM(External Passive Module)

EPM – Front (Top) and Rear (Bottom) Panels

Panel Connector Description

Front HIGH I/O One Mini DIN 4.3-10 high-band input port interfaces to HX-WCS

Four Mini DIN 4.3-10 combined output ports interface to wideband

ANT
antennas
Rear
Four N-Type low-band input ports interface to service combiner unit
LB
(SCU) on MA1000/MA2000.

.
Business Name Corning Restricted 106 .
.
Connection Guidance on EPM with 2K’s

• Step by step instructions

1. Connect the HX MUX “ANT” 4.3.-10 type duplexed RF port to the
EPM front panel high-band Mini DIN 4.3-10 input port (cable not
provided)
– Notes
• In SISO configurations, the HX
“ANT 1(MUX)” module (right) is
connected.
• In MIMO configurations, the “ANT
2(MUX)” module will be connected
to an additional EPM.

- Example High Band Connection

.
Business Name Corning Restricted 107 .
.
Connection Guidance on EPM with 2K’s

• Step by step instructions

2. Connect the four rear panel EPM low-band N-Type ports to the four
SCU N-type “ANTENNA PORTS” with appropriate coax cables (not
provided).
– Notes
• SCU-4 units – the antenna ports
are located on the rear panel.
• SCU-F/SCU-FT units – the
antenna ports are located on the
front panel.

- Example of EPM to SCU Low Band

Connections (Rack Mount)
.
Business Name Corning Restricted 108 .
.
 Connection Guidance on EPM with 2K’s

• Step by step instructions

– HX-WCS

- Example of EPM-to-SCU - Example of EPM-to-SCU - Distance Required for

Low Band Connections Low Band Connections Unobstructed High-Band Cable
(Belly-to-Wall) – Isometric (Back-to-Wall) – Isometric Connection
View View

.
Business Name Corning Restricted 109 .
.
Connection Guidance on EPM with 2K’s

• Step by step instructions

– HX-2.5GHz TDD

- Example of EPM-to-SCU - Example of EPM-to-SCU

Low Band Connections Low Band Connections
(Belly-to-Wall) – Isometric (Back-to-Wall) – Isometric
View View

.
Business Name Corning Restricted 110 .
.
Connection Guidance on EPM with 2K’s

• Step by step instructions

3. Connect the four EPM rear panel Mini DIN 4.3-10 “ANT” output
ports to the wideband antennas.
4. Terminate any unused antenna ports with a 50 ohm terminator.
– Notes: In configurations where N-type cables were originally used to
connect the SCU-4 to the wideband antenna, the cables will need to
be replaced with 4-3.10 type connector cables in order to connect
the EPM to the wideband antennas.

.
Business Name Corning Restricted 111 .
.