DOCUMENTTYPE 1 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

MSS/MGW Commands

To check alarms

ZAHO::CLS=AL1; --To see alarm class 1.-------------MSS

ZAHO::CLE=AL2;--- To see alarm class 2.
ZAHO::CLS=AL3;-- To see alarm class 3.
ZAH0::NR=2018;-- To see alarms bu number.

ZAHO; -------- To see alarm history.

ZABO; ---- To see blocked alarms

ZAAP::CLS=AL1; -------To see alarm class 1 ---------------MGW

ZAAP::CLS=AL2; ------- To see alarm class 2
ZAAP::CLS=AL3; ------- To see alarm class 3
ZAAP::NR=2018; ---- To see alarms bu number

ZAHP; --- To see alarm history

------------------------------------------------------------------------------------------------------------------------------------
PCM Status for MSS/MGW

ZYEF:ET,257; --- To see PCM status

ZYEI:ET,257; --- To see frame alignment mode of PCM. For Inter MSC and POI it should be DBLF
and for ATER it should be CRC4.

ZUSI:ET,257; ----- To chack the working status of ET it should be WO-EX always

-------------------------------------------------------------------------------------------------------------------------------------
To check the command calendar

ZICL; --- All the commnds should be in unblock condition.

ZICL::COM; ---- All the commnds should be in unblock condition.

If you find commnds are blocked then you can unblock by using the following command :-

ZICB:XX:UNBLOCK; --- Where XX means Task Identifier.

-------------------------------------------------------------------------------------------------------------------------------------
To See VMGW state

MSS

ZJGI; ----- All the VMGWs should be in Registered condition.

Also check the state of SIGU by fillowing command:-

ZUSI:SIGU; ---- All SIGUs should be in WO-EX condition except one in SP-EX.
 DOCUMENTTYPE 2 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

MGW

ZJVI; --- All the VMGWs should be in Registered condition

-----------------------------------------------------------------------------------------------------------------------------------
Fallbeck

Fallback in (HDD) in MSS/MGW

ZWQO:CR; ----- To see created software package.

ZWQO:RUN; -----To see running package.

One package should be in BU condition .

ZWQD:NAME=<PACKAGE NAME>:DIRE,::; ---------To delete old software package

ZWKS:MODE=FULL,NAME=FB160309,DIRE=FB160309::; --- To start fallback in HDD

ZWKI::; ---------- To see fallback progress

Fallback in MOD In MSS/MGW

ZIPS:"OMU",WDU-S,/FB160309,,:"OMU",FDU-0,,,:NAME=FB160309,DIR=INC,ISD=Y,:DCM=NEW,:;
To start fallback in MOD form HDD

ZIPI:ID=4002D740; -- To see the fallback progress

-----------------------------------------------------------------------------------------------------------------------------------------
Unit Checking

ZUSI; ---- To see unit state in MSS and MGW

ZUSI:COMP; --------- To see all computer units in MSS

ZUSI:<UNIT NAME>; ----- To see specific unit state in MSS and MGW
----------------------------------------------------------------------------------------------------------------------------------------
To see subscribers in VLR in MSS

ZMVI; ---- To see total subecriber count in VLRs

ZMVF::PLMN=ALL; --- To see subecribers PLMN wise

ZMVF::LAC=<LAC NUMBER>; --- To see subecriber LAC wise

ZMVO:MSISDN=919176098909; --------- To see a subecriber in VLR

ZMVS:IMSI=405800170001139:BSERV=T11; ----To see SUPPLEMENTARY services of the

subecriber in the VLR.
 DOCUMENTTYPE 3 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

ZMVR:IMSI=405800170001139:; ----- To see OPERATOR DETERMINED BARRING DATA in VLR.

ZMVG:IMSI=405800170001139:BSERV=T11; --- To see CAMEL data in VLR.

ZMVD:IMSI=405800170001139::; --- To delete a subscriber from VLR.

-------------------------------------------------------------------------------------------------------------------------------------
Signalling Route in MSS/MGW

ZNRI:NA1,D’1234; --- To see signaling route set date where 1234 is the SPC in NA1 where D
means value in Decimal

ZNRI:NA0,D’1234; ---- To see signaling route set date where 1234 is the SPC in NA0 where D
means value in Decimal

All the routes should be in AV-EX state.

ZNVA:NA0,D’1234; ----- To Allow activation of Route Set

ZNVD:NA0,D’1234; ----- To Deny activation of Route Set

ZNVC:NA0,D’1234::INA; ---------- To inactive Route

ZNVC:NA0,D’1234::INA; ---------- To activate route

----------------------------------------------------------------------------------------------------------------------------------
Link Status in MSS/MGW

ZNEL; --- To see all signaling links

ZNEL::STATE=UA; --- To see unavailable signaling links

ZOLT; ---- To see link load

ZNCC:LINK NO:PCM-TSL,BIT RATE,NO OF TSL,1:UNIT,INDEX:0:; --- To create a signaling link

For example if we give the below mention command link number 1 will be created with bitrate 64
Kbps and PCM no-124 and TSL-16 in CCSU unit 2.

ZNCC:1:124-16,64,1,1:CCSU,2:0:;

ZNEL:1; --- To see signaling link

ZNSC:NA1,D'1234,TEST:1,0:; ---- To create link SET

ZNSI:NA1,D'1234:; --- To see link set data

ZNSA:NA1,D'1234,TEST:2,1:; --- To add link to a link set

-------------------------------------------------------------------------------------------------------------------------------------------

Clock SYNCHRONIZATION

ZDRI; ----------- To see external clock synchronization STATE should be connected in MSS
 DOCUMENTTYPE 4 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

ZUSI:CLS; --- To see internal clock one should bw WO-EX and another should be in SP-EX in
MSS

ZUSI:TBU; -- To see internal clock one should bw WO-EX and another should be in SP-EX in
MGW

ZDYI; -- To see external clock synchronization STATE should be connected in MGW

ZDCD; --- To see the real time of MSS/MGW

----------------------------------------------------------------------------------------------------------------------------------------
I/O Device Interogation

ZISI:,<UNIT>:<I/O DEVICE>,; ----- To see i/o devices state(ZSI:,OMU:WDU,;) in MSS

ZIHI:,<UNIT>:<I/O DEVICE>,; ----- To see i/o devices state(ZHI:,OMU:WDU,;) in MGW

ZIFI:CHU,0:GSMCHA:; -------------- To see status of the storage data

ZUSI:CHU; ---- To see CHU unit state in MSS

ZIFO:CHU,0:GSMCHA:,OPEN,; ---- To see open file in CHU in MSS

ZIFO:CHU,0:GSMCHA:,FULL; --- To see full file in CHU in MSS

ZIFO:CHU,0:GSMCHA::; ------ To see all file status in CHU in MSS

-------------------------------------------------------------------------------------------------------------------------------------------

To see LICENCE and FEATURE in MSS/MGW

ZW7I:LIC,FULL; ---- To see licence capacity

ZW7I: FEA, FULL:FSTATE=ON; ---- To see features in on state

-------------------------------------------------------------------------------------------------------------------------------------------
SCTP Configuration Command in MSS/MGW

ZOYI; -- To see SCTP Configuration date

ZOYI:NBR=0:A:; ---- To see SCTP Configuration with all details

-------------------------------------------------------------------------------------------------------------------------------------------
GT Analysis and Result Record in MSS

ZNBI::TT=0,NP=1,NAI=4,:9197169; ---- To see GT analysis for SMS (NP=1)

ZNBI::TT=0,NP=7,NAI=4,:9197169; ----- To see GT analysis for Location Update(NP=7)

From the output we will get a RESULT Record for example as below RES is 6.

RESULT ANALYSIS
SS7 GTI TT NP NAI DIGITS RECORD TYPE
 DOCUMENTTYPE 5 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

---- --- --- --- --- ------------------------ ------ --------

ITU 4 0 1 4 9197169 6 BASIC

ZNAI:RES=6; ---- To see the SPC for Result Record

To create Result Record we have to create Signalling Route with MML Command as below:-
ZNRC:NA1,D'1234,TEST,0,A,N:NA1,D'1234,TEST,7::::;

ZNRI:NA1,D'1234:; --- To see route set data

ZNVA:NA1,D'1234:NA1,D'1234:;

ZNVC:NA1,D'1234:NA1,D'1234:ACT;

Then we have to define SCCP with following command:-

ZNFD:NA1,D'1234,0:6,MAPH,0,:7,MAPV,0,:8,MAPM,0,:92,CAP,0,::;

ZNHI:NA1,D'1234; --- To see SCCP data

ZNHI:NA1,D'1234; --- To see SCCP data

ZNGC:NA1,D'1234:ACT;

ZNHC:NA1,D'1234:6:ACT;

ZNHC:NA1,D'1234:7:ACT;

ZNHC:NA1,D'1234:8:ACT;

ZNHC:NA1,D'1234:92:ACT;

Then use following command to create Result Record

ZNAC:NET=NA0,DPC=D'1234,RI=GT,:::; --- To create Result Record

ZNAI:RES=<RESULT RECORD NUMBER>; ---- To see the output

For example

ZNAI:RES=6;

INQUIRING GLOBAL TITLE TRANSLATION RESULT

RESULT LS SP ENTITY LS
RECORD STA IND NET SP CODE H/D NAME RI STATE PR WGHT
------ --- --- --- ------------------ ----- --- ------ -- ----
00006 ACT NO NA1 13C4/05060 HLR01 SSN AV-EX - -

For example RES 6 is routed to SPC- 5060(HLR01).

 DOCUMENTTYPE 6 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

Then we will check with the following command –

ZNRI:NA1,D’5060;

INTERROGATING SIGNALLING POINT DATA

NET SP CODE H/D NAME RS STATE PAR SET

--- ------------------ ----- -------- -------
NA1 13C4/05060 HLR01 AV 6
LOAD SHARING BETWEEN SIGNALLING ROUTES ALLOWED

ROUTES: SP CODE H/D NAME STATE PRIO

------------------ ----- ------ ----
13C4/05060 HLR01 AV-EX 7

CGR Commands

ZRCI; --- To see all the CGRs in MSS/MGW

ZCEL:CGR=404; --- To see calls in a CGR in MSS

ZCII:CGR=555; --- To see calls in a CGR in MGW

ZRCI:SEA=3:CGR=404:PRINT=2; ---- To see Circuit Group parameters

ZRCI:SEA=3:CGR=404:PRINT=5; --- To see all CGR parameters

ZRCI:SEA=3:CGR=404:PRINT=4; --- To see all circuits in CGR

If you want to know a PCM is connected to which CGR then give the below mentioned
command:-

ZRCI:SEA=4:CRCT=264-1&&-31; -- Where 264 is the PCM number

To change the state of the circuits in a CGR first give the below mentioned command

ZRCI:SEA=3:CGR=404:PRINT=4;

Kindly note down the PCM numbers and then the below command

ZRCI:SEA=3:CGR=404:PRINT=2;

MAIN LEVEL COMMAND <___>

< RCI:SEA=3:CGR=404:PRINT=2;

LOADING PROGRAM VERSION 12.52-0

CIRCUIT GROUP(S)
 DOCUMENTTYPE 7 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

CGR : 404 NCGR : BSCVIK1E

TYPE : ECCS STATE : WO-EX HUNTED : YES

FORMAT : TERMID HM1 : LF HM2 : LF
NBCRCT : 1392 TREE : - DIR : OUT
LSI : AIF02 INR :- NCCP : -
METHOD : - NET : NA1 SPC(H/D) : 1C8B/07307
ASI :-
UPART : BSSAP MGW : MSS01MGW0103

FQDN :-

AUTOMATIC CONGESTION CONTROL

REJ11 : - REJ12 : - REJ21 : - REJ22 : -

ACT11 : NO ACTION ACT12 : NO ACTION ACT21 : NO ACTION ACT22 : NO ACTION

SELECTIVE CIRCUIT RESERVATION

TRES1 : - TRES2 : -
DR1A : - DR2A : - ART1A : - ART2A : - ACTA : NO ACTION
DR1B : - DR2B : - ART1B : - ART2B : - ACTB : NO ACTION
DR1C : - DR2C : - ART1C : - ART2C : - ACTC : NO ACTION

COMMAND EXECUTED

Then copy the VMGW name (MSS01MGW0103) and then give the below command in MSS only

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:BA; --- To bar the circuits where 10274 is

the PCM number

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:NU; --- To not use the circuits in MSS

ZCIM:CRCT=1234-1&&-31:WO; -- To change the state of the circuit in MGW

ZRCC:TYPE=ECCS,CGR=329,NCGR=BSC34SUR:DIR=OUT,NET=NA1,SPC=D'7034,LSI=AIF02,
UPART=5:MGW=ASMGW202:; --- To create CGR 329, with Name- BSC34SUR, SPC-7034, and
VMGW- ASMGW202

ZRCC:TYPE=SPE,CGR=329,NCGR= BSC34SUR:USE=VMGW:; -- To create CGR in MGW

ZCRM:CGR=329:WO; ---- To change the STATE of the CGR in MSS

ZCIM:CGR=329:WO; ---- To change the STATE of the CGR in MGW

ZRRC:EXT:ROU=329,OUTR=OMCG0,NCCP=MAS,STP=1,TON=UNK,NCGR=BSC34SUR; --- To
create Traffic ROUTE in MSS only

ZRCA:CGR=404:TERMID=10234-1&&-31,:CCSPCM=0::UNIT=BSU,INDEX=8:; --- To add circuits in

a CGR in MSS only

ZRCA:CGR=329:CRCT=1234-1&&-31; To add circuits in a CGR in MGW only

 DOCUMENTTYPE 8 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

-------------------------------------------------------------------------------------------------------------------------------------------
IMSI Analysis for Inroaming in MSS

ZCFC:IMSI= 72431,IMSIINDIC=2,PLMN=PCS_BRAZIL,TOA=GT,:NP=E214,TON=INT,SRD=1,NRD=5,
SAD=1,DIA=55031,:; --- To create IMSI analysis

ZCFI:TYPE=IMSI:DIG=72431:ALL; ---- To see the o/p of the analysis

ZMXP:NAME= PCS_BRAZIL; --- To see PLMN parameters and check the Supported CAMEL
Phaze

IMSI NUMBER ANALYSES

IMSI IMSI PLMN GT NP TON NI SPC

NBR. IND.

72431 2 PCS_BRAZIL 55031 E.214 INT - -

NUMBER MODIFICATION RULES: START POINT OF REMOVED DIGITS : 1

NUMBER OF DIGITS REMOVED : 5
START POINT OF ADDED DIGITS : 1
ADDED DIGITS : 55031

ZCFD:TYPE=IMSI:DIG=72431; ---- To delete imsi analysis

From the IMSI analysis o/p check the GT analysis properly with command ZNBI:::55031;

Tracing command in MSS

ZMWC:MSISDN=919716098909:REF=122,:; - To activate trace of a number in MSS

Then give command ZQNS; - to see in which VTP you have logged in. This command shows the
command you fired last.

< ZQNS;

LOADING PROGRAM VERSION 12.4-0

MSCi MSS01_GGN 2009-03-16 14:15:35 PAGE 1

SYSTEM USERNAME USER USER MML SESSION

SYSTEM I/O-DEVICE NUMBER

220366 MSS01_GGN SYSTEM 220366 MSS01_GGN OMU-VTP20 RI 01244

SYSOP1 220366 MSS01_GGN OMU-VTP15 QN 01237

COMMAND EXECUTED

From above o/p the logged VTP would be VTP-15 , because in its right side it is showing QN
command which you fired last.

Then give the command - ZIIS::GSMME1PR::DEV=VTP-15;

 DOCUMENTTYPE 9 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

LOGICAL FILE MODIFIED:

SYSTEM = MSS01_GGN UNIT = OMU

PAGE 1
LOG LOG SPARE PHYSICAL OBJ SYSTEM UNIT DEVICE/
FILE FILE FILE FILE IND NAME NAME LOGICAL
NBR NAME & CLASS MODE NAME FILE

93 GSMME1PR P /TRACE/ 1 MSS01_GGN OMU WDU-SB

GSMME1PR.TXT,0 2 MSS01_GGN OMU VTP-23
(** RING FILE **) 3 MSS01_GGN OMU VTP-15

COMMAND EXECUTED

Please note! In device list WDU-SB should be always connected to OMU. At a time max 4 device
can be connected one is WDU-SB of OMU and three are different VTP or LPT.

If you find that 4 devices are already connected and you want to connect another device then you
have to give the followind command:-

ZIIS::GSMME1PR:IND=3:DEV=VTP-15;

In this case IND=3 position VTP would be disconnected and new VTP would be added.
You can also give IND=2 or IND=4 according to the situation. Please do not disconnect the WDU-
SB from OMU.

We can also take trace using the below mentioned command at the time of call test

ZMCJ:IMSI=<IMSI NUMBER>::TYPE=D;

DIAGNOSTIC in MSS/MGW

To do diagonesis of an unit it should be in test mode. For example if we want to diagonose a ET

no 258 then we have to change its working state with to TE with command as below:-

ZUSC:ET,258:BL; ---- To block the ET

ZUSC:ET,258:TE; --- To change in to test mode

ZUDU:ET,258:::; ---- To start the daigonesis of the ET

ZUDQ; ---- To see current diagonesis test

ZUDH:ET,258:::; --- To see the diagonesis history

 DOCUMENTTYPE 10 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

Switchover of Units in MSS/MGW

If we want to switchover the state of an unit we have to use the procedures as below:-

ZUSI:OMU; --- To see the present state of an unit (OMU)

WORKING STATE OF UNITS

UNIT PHYS STATE LOCATION INFO
OMU-0 0000 WO-EX -
OMU-1 0001 SP-EX -

TOTAL OF 2 UNITS

COMMAND EXECUTED
Now if we want to change the state of OMU to WO-EX from SP-EX then we have to give the
following command:-

ZUSC:OMU,0:SP,:; --- To switchover the OMU 1 from SP-EX to Wo-EX.

After the command execution the O/P will be as follows:-

WORKING STATE OF UNITS

UNIT PHYS STATE LOCATION INFO
OMU-0 0000 SP-EX -
OMU-1 0001 WO-EX -

TOTAL OF 2 UNITS

COMMAND EXECUTED

Directed Call Test in MSS

Trunk to trunk test call

For trunk to trunk call e.g POI and Inter MSC call test we have to take a B party test number first.

Then we have to define test case by following command :-

ZYCN:<TEST CASE NAME>:OUTROUT=Y,DIG=9716098909,CON=NAT,CONT=N,:;

Where DIG= B party number

If a testcase is already active deactivate it using the command ----- ZYCE:4:;

Now activate the newly created testcase with the command

ZYCS: <TEST CASE NAME>,4;

Make the A party number in TP in HLR (from where you initiate the calls) with command
 DOCUMENTTYPE 11 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

ZMIM:IMSI=<IMSI NUMBER>:CAT=TP;

Now make the desired circuits in TE-ID mode with command

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:TE;

Now do test call and check the circuit with command ZMCJ:IMSI=<IMSI NUMBER>;

Call Testing for MOC (In case of ATER call test)

In this case we can do test calls for ATER where A party has to initiate a call provided A party
would be under the same BSC for which call test is being done.

Then we have to define test case by following command :-

ZYCG:<TEST CASE NAME>:OUTROUT=Y,DIG=9716098909,CON=LOC,CONT=N,:;

Where DIG= B party number

If a testcase is already active deactivate it using the command ----- ZYCE:4:;

Now activate the newly created testcase with the command

ZYCS: <TEST CASE NAME>,4;

Make the A party number in TP in HLR (from where you initiate the calls) with command

ZMIM:IMSI=<IMSI NUMBER>:CAT=TP;

Now make the desired circuits in TE-ID mode with command

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:TE;

Now do test call and check the circuit with command ZMCJ:IMSI=<IMSI NUMBER>;

Call Testing for MTC (In case of ATER call test)

In this case we can do test calls for ATER where B party has to initiate a call provided B party
would be under the same BSC for which call test is being done.

Then we have to define test case by following command :-

ZYCM:4:INROUT=Y,CONT=N,:

If a testcase is already active deactivate it using the command ----- ZYCE:4:;

Now activate the newly created testcase with the command

ZYCS: <TEST CASE NAME>,4;

 DOCUMENTTYPE 12 (12)

TypeUnitOrDepartmentHere
TypeYourNameHere TypeDateHere

Make the B party number in TP in HLR (from where you initiate the calls) with command

ZMIM:IMSI=<IMSI NUMBER>:CAT=TP;

Now make the desired circuits in TE-ID mode with command

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:TE;

Now do test call and check the circuit with command ZMCJ:IMSI=<IMSI NUMBER>;

Creation of Directory and files in MSS/MGW

ZIWL::WSB,NODEF::TEST,FF,,AA:; ---- To create the TEST directory

ZIWX::WS,NODEF:TEST,:%,%,; ----- To see the containts of the TEST directory

ZIWC::WSB,NODEF:TEST,:TEST,TXT,20000000,AA:; --- to create TEXT.TXT under the directory

TEST

Measurement Commands in MSS

ZTMI:<NAME OF MEASUREMENT>;

ZTGI:CGR,1; --- To see object list

If we create a new CGR then we have to add the CGR in object lis for measurement
The commands are as follows:-

ZTGC:CGR,1:CGR=400:; ---- CGR 400 would be added in object list 1

General Commands in MSS

ZTUT:CLR; ---- To see clear codes generated in MSS

ZTUL:CLR; ----- To see clear code generated in last hour

ZMCJ:ALL=N; ----- To see number of call records in MSS