Scribd
Upload
224 views

QPSK Modulation and Demodulation PDF

QPSK modulation encodes 2 bits per symbol by varying the phase of two carrier signals (sinusoids) by 0, 90, 180, or 270 degrees. This results in constellation points on the in-phase and quadrature axes. A QPSK modulator uses a serial-to-parallel converter to separate bits into the I and Q arms, then multiplies each by a cosine or sine carrier. QPSK demodulation requires coherent detection with a carrier recovery system. The received signal is multiplied by cosine and sine carriers, and the outputs are integrated and compared to a threshold to detect the bits on each arm.

Uploaded by

Komal Verma
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
224 views

QPSK Modulation and Demodulation PDF

QPSK modulation encodes 2 bits per symbol by varying the phase of two carrier signals (sinusoids) by 0, 90, 180, or 270 degrees. This results in constellation points on the in-phase and quadrature axes. A QPSK modulator uses a serial-to-parallel converter to separate bits into the I and Q arms, then multiplies each by a cosine or sine carrier. QPSK demodulation requires coherent detection with a carrier recovery system. The received signal is multiplied by cosine and sine carriers, and the outputs are integrated and compared to a threshold to detect the bits on each arm.

Uploaded by

Komal Verma
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

QPSK MODULATION AND

DEMODULATION
QPSK Modulation:

In digital modulation techniques a set of basis functions are chosen for a particular modulation

scheme.Generally the basis functions are orthogonal to each other. Basis functions can be

derived using ‘Gram Schmidt orthogonalization’ procedure.Once the basis function are chosen,

any vector in the signal space can be represented as a linear combination of the basis functions.

In Quadrature Phase Shift Keying (QPSK) two sinusoids (sin and cos) are taken as basis

functions for modulation. Modulation is achieved by varying the phase of the basis functions

depending on the message symbols. In QPSK, modulation is symbol based,where one symbol

contains 2 bits. The following equation outlines QPSK modulation technique.

si(t)=2EsT−−−−√cos(2πfct+(2n−1)π4),n=1,2,3,4

When n=1, the phase shift is 45 degrees. This is called pi/4 QPSK.The constellation diagram of

QPSK will show the constellation points lying on both x and y axes.This means that the QPSK

modulated signal will have an in-phase component (I) and also a quadrature component (Q). This

is because it has only two basis functions.

A QPSK modulator can be implemented as follows. A demultiplexer (or serial to parallel

converter) is used to separate odd and even bits from the generated information bits. Each of the

odd bits (quadrature arm) and even bits (in-phase arm) are converted to NRZ format in a parallel

manner.
The signal on the in-phase arm is multiplied by cosine component and the signal on the

quadrature arm is multiplied by sine component. QPSK modulated signal is obtained by adding

the signal from both in-phase and quadrature arm.

QPSK Modulator

QPSK Demodulation:

For QPSK demodulator , a coherent demodulator is taken as an example. In coherent detection

technique the knowledge of the carrier frequency and phase must be known to the receiver. This

can be achieved by using a PLL (phase lock loop) at the receiver. A PLL essentially locks to the

incoming carrier frequency and tracks the variations in frequency and phase. For the following

simulation , a PLL is not used but instead we simple use the output of the PLL.
For demonstration purposes we simply assume that the carrier phase recovery is done and simply

use the generated reference frequencies at the receiver (cos(ωt)) and (sin(ωt)).

In the demodulator the received signal is multiplied by a reference frequency generators

(cos(ωt)) and (sin(ωt)) on separate arms (in-phase and quadrature arms). The multiplied output

on each arm is integrated over one bit period using an integrator. A threshold detector makes a

decision on each integrated bit based on a threshold. Finally the bits on the in-phase arm (even

bits) and on the quadrature arm (odd bits) are remapped to form detected information stream.

Detector for in-phase arm is shown below. For quadrature arm the below architecture remains

same but sin(ωt) basis function must be used instead.

QPSK Demodulator – In-phase arm

Source: http://www.gaussianwaves.com/2010/10/qpsk-modulation-and-demodulation-2/

You might also like