4

4 Red Battery 12V (+)

Shock
3 3 Black Data TX
2 2 Green Warn Away Input (-)
1 Blue Full Trigger Input (-)
1
Replacement Part #4700033

2 Gray Valey Switch Input (-)

Valet
1 Black Ground Output (-)
2 Red Battery 12V (+)

LED
1 Blue LED Output (-)
Replacement Part #4120474

VOXX 2
2 Green Unlock Output (-)

Door
Lock
Replacement Part #4360842 1
1 Red Lock Output (-)
Replacement Part #4120469

85 Red
87
Ignition Input (+)

Starter Kill
87A 86 Orange Starter Kill Input (-)
86 85
87A Black Starter Interrupt - Key Side
30 30 White/Black Starter Interrupt - Motor Side
Replacement Part #4360828

1 2 3 4 5 6 7 8 9 10 11

1 White Parking Light Output (30)

Shock Sensor
2 White/Red Parking Light Input (87) Part #4700033
3 Dk. Blue Trunk Output (-)
4 White/Black Siren Output (+)
11 Pin Main

5 Red Battery 12V Input (+)

6 Black Ground Input (-) Replacement Part # 183BP
7 Yellow Ignition Input (+)
8 Light Green Instant Trigger Input (-)
9 Brown Door Input (-)
10 Purple Door Input (+)
11 Orange Starter Kill Output (-)
Replacement Part #4120468

APS25Z
Security System Layout
2018 Voxx Electronics. All Rights Reserved.
 Options
Feature Bank 2
1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp
1 Lock / Unlock Function 500ms 3.5sec 500ms L, Dbl UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Accessory Lock OFF ON
3 Accessory Unlock OFF ON

Features
4 Auto Relock OFF Auto Lock Auto Lock & Arm
5 Auto Arming OFF Auto Arm Auto Lock & Arm
6 Parking Light/Trunk Swap OFF ON
7 Silent Choice OFF From Transmitter OEM Style
8 Exterior Illumination OFF With Arm With Disarm With Arm & Disarm

APS25Z Remote Programming Shock Sensor

Security with Keyless Entry The APS25Z includes two (2) programmed remotes. If required, additional The shock sensor should be mounted to a solid surface in the center of the
remotes can be programmed to the system. Remote Programming is located in vehicle. Once mounted the shock sensor will require adjustment.
Feature Bank 1. To enter Remote Auto Programming:

Quick Installation Guide

To increase sensitivity: Turn adjustment dial clockwise.
1. Turn the ignition key to ON. To decrease sensitivity: Turn adjustment dial counter clockwise.
2. Press and release the valet button 3x. System will beep and flash the
For Complete Installation Guide and Technical Support Please parking lights 1x. To test sensitivity, strike the vehicle with an open palm. Adjust the dial to
Visit provide coverage to as much of the vehicle as possible.
Press the lock button on each remote. The system will beep 1x to indicate the
www.voxxuniversity.com remote has been programmed.
Or Call
1-800-225-6074
2018 Voxx Electronics. All Rights Reserved.

Notifications Feature Programming Dome Delay Programming

Alarm
When the alarm is triggered the system will provide feedback to the user. The APS25Z Feature Bank can be programmed by using the valet button and This system can be programmed to ignore the vehicle’s theater dimming
Upon disarm, the system will beep 4x and flash the LED to indicate the Alarm remote. To enter Feature Bank programming: dome light. This feature will be used when connecting the door trigger
Trigger Zone. input to the dome light circuit for alarm trigger. Note: Vehicle windows
1. Turn the ignition key to ON. should be open to prevent accidental locking of keys in the vehicle.
1 Shock 2. Press and release the valet button 3x. System will beep and flash lights 1x
for Feature Bank 1, Remote Programming. Start with all doors closed and the vehicle dome light off.
2 Trunk/Hood
3. Cycle ignition key OFF/ON. System will beep and flash lights 2x for 1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light
3 Door Feature Bank 2. solid.
Chirp Delete 4. Press valet button to cycle features. LED will flash to display feature 2. Open and close the driver door.
System ARM/DISARM chirps can be toggled ON or OFF without entering the number.
Feature Bank programming. 5. Press lock button to cycle options. System will beep to indicate option The system will monitor the dome light circuit. When the dome light turns
number. off the system will set the delay time and add an additional two (2) seconds.
1. Turn the ignition key ON/OFF.
2. Press and release the valet button 3x. To exit Programming cycle ignition key OFF and wait ten (10) seconds. The Dome Delay Reset
System will also automatically exit programming after sixty (60) seconds of no 1. Key ON/OFF, ON/OFF, ON/OFF.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. activity. 2. Press and hold valet button for five (5) seconds.
This feature will not affect alarm trigger or programming.
User Programmable LED The system will beep 1x to indicate reset is complete.
System LED notifications can be turned ON or OFF without entering Feature
Bank programming.

1. Turn the ignition key ON/OFF, ON/OFF.

2. Press and hold valet button for five (5) seconds.

The LED will flash 1x for ON, 2x for OFF. This feature will not affect LED flash
during programming.