SA 07.1 – SA 16.1/SAR 07.1 – SAR 16.

1
Spare parts

13. Spare parts

38
SA 07.1 – SA 16.1/SAR 07.1 – SAR 16.1
Spare parts

Information: Please state type and commission no. of the device (see name plate) when ordering spare parts.
Only original AUMA spare parts should be used. Failure to use original spare parts voids the warranty and exempts
AUMA from any liability. Delivered spare parts may slightly vary from the representation.
No. Designation Type No. Designation Type
001.0 Housing Sub-assembly 516.1 Output drive shaft D
002.0 Bearing flange Sub-assembly 535.1 Snap ring
003.0 Hollow shaft without worm wheel Sub-assembly 539.0 Screw plug
005.0 Worm shaft Sub-assembly 542.0 Handwheel with ball handle Sub-assembly
005.1 Motor coupling 549.1 Output drive sleeve B3/B4/E
005.2 Coupling pin 551.1 Parallel key
005.3 Manual drive coupling 553.0 Mechanical position indicator Sub-assembly
005.4 Pull rope 554.0 Socket carrier with motor cable har- Sub-assembly
ness
006.0 Worm wheel 556.0 Potentiometer for position transmitter Sub-assembly
009.0 Planetary gear for manual drive Sub-assembly 556.1 Potentiometer without slip clutch Sub-assembly
010.0 Retaining flange Sub-assembly 557.0 Heater Sub-assembly
017.0 Torque lever Sub-assembly 558.0 Blinker transmitter including pins at Sub-assembly
wires (without impulse disc and insula-
tion plate)
018.0 Gear segment 559.0-1 Control unit with torque switching Sub-assembly
heads and switches
019.0 Crown wheel Sub-assembly 559.0-2 Control unit with magnetic limit and Sub-assembly
torque transmitter (MWG) for Non-in-
trusive version in combination with
AUMATIC integral controls
020.0 Swing lever Sub-assembly 560.0-1 Switch stack for direction OPEN Sub-assembly
022.0 Drive pinion II for torque switching Sub-assembly 560.0-2 Switch stack for direction CLOSE Sub-assembly
023.0 Output drive wheel for limit switching Sub-assembly 560.1 Switch for limit/torque switching
024.0 Drive wheel for limit switching Sub-assembly 560.2 Switch case
025.0 Locking plate Sub-assembly 566.0 Position transmitter RWG Sub-assembly
058.0 Wire for protective earth (pin) Sub-assembly 566.1 Potentiometer for RWG without slip Sub-assembly
clutch
061.0 Torque switching head Sub-assembly 566.2 Electronic board RWG Sub-assembly
070.0 Motor (VD motor incl. no. 079.0) Sub-assembly 566.3 Wire harness for RWG Sub-assembly
079.0 Planetary gear for motor drive Sub-assembly 567.1 Slip clutch for potentiometer/RWG Sub-assembly
(SA/SAR 07.1 – 14.1 for VD motor)
080.0 Planetary gear for motor drive Sub-assembly 568.1 Stem protection tube (without cap)
(SA/SAR 16.1 for AD90 motor)
155.0 Reduction gearing Sub-assembly 568.2 Cap for stem protection tube
500.0 Cover for switch compartment Sub-assembly 568.3 V-Seal
501.0 Socket carrier (complete with sockets) Sub-assembly 569.0 Change-over lever assy
502.0 Pin carrier without pins Sub-assembly 569.1 Change-over lever
503.0 Socket for controls Sub-assembly 569.2 Notched pin
504.0 Socket for motor Sub-assembly 574.1 Radial seal output drive A for ISO
flange
505.0 Pin for controls Sub-assembly 575.1 Stem nut type A
506.0 Pin for motor Sub-assembly S1 Seal kit, small Set
507.0 Plug cover Sub-assembly S2 Seal kit, large Set
511.0 Threaded plug Sub-assembly
514.0 Output drive form A (without stem nut) Sub-assembly
514.1 Axial needle roller bearing Sub-assembly

39