Scribd
Upload
5K views

BMW Remote Coding Through VPN

This document provides instructions for remotely coding BMW, Mini, and Rolls-Royce vehicles using E-Sys software over a VPN connection in 3 steps: 1) Configure the local coding PC with E-Sys, VPN software, and remote desktop access. 2) Configure the remote laptop connected to the vehicle with VPN software and enable port forwarding to allow remote access. 3) Connect E-Sys on the local PC to the remote laptop VPN address to code the vehicle remotely as if it was connected directly.

Uploaded by

munkarobert
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
5K views

BMW Remote Coding Through VPN

This document provides instructions for remotely coding BMW, Mini, and Rolls-Royce vehicles using E-Sys software over a VPN connection in 3 steps: 1) Configure the local coding PC with E-Sys, VPN software, and remote desktop access. 2) Configure the remote laptop connected to the vehicle with VPN software and enable port forwarding to allow remote access. 3) Connect E-Sys on the local PC to the remote laptop VPN address to code the vehicle remotely as if it was connected directly.

Uploaded by

munkarobert
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

HOW TO CODE BMW,

MINI, ROLLS-ROYCE
REMOTELY THROUGH
VPN – April 2019

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 1 OF 10


Requirements on the local PC (BMW coder PC)

– Windows 7, 8 or 10
– Full activated E-SYS with valid Token
– Hamachi VPN client by Logmein (https://www.vpn.net/)
– Remote desktop access software such as Ultraviewer (free) or Teamviewer

Requirements on the remote PC

– Windows 7, 8 or 10
– Hamachi VPN client by Logmein (https://www.vpn.net/)
– Remote desktop access software such as Ultraviewer (free) or Teamviewer
– ZGW_SEARCH.exe & MSWINSCK.OCX (From C:\EDIABAS\Hardware\ENET) – No need
to install BMW Standard Tools on the remote PC, unless you require.
– ENET OBD cable
– Laptop with RJ45 port

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 2 OF 10


How to configure and prepare your PC as the BMW coder

1. Install and register Hamachi with a valid email address


2. Create a network name and assign a password

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 3 OF 10


You can manage your network and clients online from the logmein.com website (Free up to 5
clients, delete clients as you need, so you don't have to pay)

3. Make sure your E-SYS is functional and up to date


4. Make sure your remote desktop client is functional and up to date

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 4 OF 10


How to configure and prepare the remote PC

Prior to performing the installation and configuration tasks, make sure the laptop has just been
started, sometimes laptop that come back from sleep have network issue until full rebooted.

Also make sure the ENET OBD plug is connected to the car and the laptop and that the car
engine is started.

Finally it will save you time to have ZGW_Search.exe and the MSWINSCK.OCX files ready to
download from sites such as MEGA or GOOGLE DRIVE prior to connect to the remote PC. If
ZGW_Search complains about missing OCX, run the tool as an administrator and/or register
the OCX file using the Windows command command Regsvr32

Copy the MSWINSCK.OCX to C:\Windows\System32 for example, then run the CMD.EXE
as an administrator and execute the following command.

1. Login to the remote PC and switch off any firewall and Anti Virus.

2. Run ZGW_SEARCH.exe to figure out the car's IP address (It should be 169.254.x.y)
If no address are coming up, make sure the relevant network interface is set to DHCP
on the laptop and that the car is started/ENET OBD plug is connected.

Sometimes it is not possible to pick up the car's IP if it has been opened for a while, if
that happens, simply lock the car for 5mn and try again (Disconnect OBD lead, switch
off engine, car locked)

3. Add a local entry to Windows network table with the following steps
- As an administrator, start a Command prompt Window
- In the command prompt window, paste the following command and adjust the IP
address to the one you found with ZGW_Search

netsh int portproxy add v4tov4 listenport=6801 connectport=6801 connectaddress=169.254.x.y

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 5 OF 10


Run the Command Prompt as an administrator in order to change the network settings

Ok Press Enter and you have now configured the laptop to accept incoming network traffic the
the network port 6801

4. You will now need to do the same with the Hamachi client.
Click System > Preferences...

Then go to Advanced settings...

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 6 OF 10


From the Advanced settings menu, go to Peer Connections area and add the following new
values in the Local UDP / TCP address

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 7 OF 10


Enter the value 6801 on both UDP and TCP fields (2nd box only), Click Set for each line.
Click OK, the remote PC is now fully configured

Now on the your coding PC, click the Start button as highlighted below

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 8 OF 10


Once the network is started on your local PC, do the same on the remote PC, make sure the
remote PC is configured to join your your previously set up network. If not, then join now.

After the remote PC has joined your Hamachi VPN network, then take note of the remote
client's VPN address (Usually starts with 25.x.y.x) and use this IP address in order to connect
E-SYS as highlighted on the next screenshot

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 9 OF 10


Congratulations, you are now able to code the remote vehicule using E-SYS through VPN
network.

Select the chassis as usual, then click the Connection via gateway URL an enter the HAMACHI
VPN IP address of the remote client.

Finally click Connect and you will be able to proceed with the car coding as usual, as if the car
was local to you.

BMW F, G, I SERIES REMOTE CODING WITH E-SYS THROUGH VPN – PAGE 10 OF 10

You might also like