Scribd
Upload
30 views

Mata Pelajaran: Admin Infra Jaringan Guru: Lukman, Se, M.Kom

This document provides instructions for a jobsheet on configuring OSPF routing between five routers (Router A, B, C, D, E) in a network topology. The steps include: 1) building the topology; 2) configuring IP addresses on each router's serial interfaces; 3) testing connectivity before OSPF; 4) setting the OSPF process and networks on each router; and 5) testing connectivity after OSPF is configured. The configuration is performed to establish routing between all routers in the network using OSPF routing protocol.

Uploaded by

Dias Ferdiansyah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
30 views

Mata Pelajaran: Admin Infra Jaringan Guru: Lukman, Se, M.Kom

This document provides instructions for a jobsheet on configuring OSPF routing between five routers (Router A, B, C, D, E) in a network topology. The steps include: 1) building the topology; 2) configuring IP addresses on each router's serial interfaces; 3) testing connectivity before OSPF; 4) setting the OSPF process and networks on each router; and 5) testing connectivity after OSPF is configured. The configuration is performed to establish routing between all routers in the network using OSPF routing protocol.

Uploaded by

Dias Ferdiansyah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 9

MATA PELAJARAN : ADMIN INFRA JARINGAN

GURU : LUKMAN, SE, M.KOM

JOBSHEET ROUTING OSPF

KELOMPOK : Eldias Ferdiansyah


Resa Novita Sari
KELAS : XII TKJ 2

TP.2018/2019
1. Buatlah topologinya
2. Atur IP Serial router :
Router A :
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/1
Router(config-if)#ip address 192.168.3.2 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/3/1, changed state to up
Router(config-if)#ex
Router(config)#ex
%SYS-5-CONFIG_I: Configured from console by console
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed
state tocop
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]

Router#enable
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/0
Router(config-if)#ip address 172.16.1.1 255.255.128.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/3/0, changed state to down
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]

Router B :
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/1
Router(config-if)#ip address 192.168.3.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/3/1, changed state to down
Router(config-if)#
Router(config-if)#clock rate 64000
This command applies only to DCE interfaces
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/0
Router(config-if)#ip address 192.168.1.2 255.255.254.0
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/3/0, changed state to up
Router(config-if)#clock rate 64000
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed
state to up
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]

Router C :
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/0
Router(config-if)#ip address 172.16.1.2 255.255.128.0
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/1
Router(config-if)#ip address 192.168.10.2 255.255.255.240
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/3/1, changed state to down
Router(config-if)#
Router(config-if)#clock rate 64000
This command applies only to DCE interfaces
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router D :

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/1
Router(config-if)#ip address 192.168.10.1 255.255.255.240
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/3/1, changed state to down
Router(config-if)#
Router(config-if)#clock rate 64000
This command applies only to DCE interfaces
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]

Router E :

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/3/0
Router(config-if)#ip address 192.168.1.1 255.255.254.0
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
3. Tes kirim pesan sebelum router di routing ospf

Router D Router C = Connect


Router C Router A = Connect
Router A Router B = Connect
Router B Router E = Connect

4. Setting ip route ospf


Router A :
Router>en
Router#conf t
Router(config)#router ospf 25
Router(config)#network 192.168.3.0 0.0.255 area 0
Router(config)#network 172.16.0.0 0.0.127.255 area 0
Router(config-router)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#

Router B :
Router>en
Router#conf t
Router(config)#router ospf 25
Router(config)#network 192.168.3.0 0.0.255 area 0
Router(config)#network 192.168.1.0 0.0.1.255 area 2
Router(config-router)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#

RouterC :
Router>en
Router#conf t
Router(config)#router ospf 25
Router(config)#network 192.168.10.0 0.0.0.15 area 1
Router(config)#network 172.16.0.0 0.0.127.255 area 0
Router(config-router)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#

Router D :
Router>en
Router#conf t
Router(config)#router ospf 25
Router(config)#network 192.168.1.0 0.0.0.15 area 0
Router(config-router)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#

Router E:
Router>en
Router#conf t
Router(config)#router ospf 25
Router(config)#network 192.168.1.0 .0.0.1.255 area 0
Router(config-router)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#
5. Tes kirim pesan sesudah router di setting ospf

Router A - Router B = Successfull


Router A - Router C = Successfull
Router A - Router D = Successfull
Router A - Router E = Successfull
Router B - Router A = Successfull
Router B - Router C = Successfull
Router B - Router D = Successfull
Router B - Router E = Successfull
Router C - Router A = Successfull
Router C - Router B = Successfull
Router C - Router D = Successfull
Router C - Router E = Successfull
Router D - Router A = Successfull
Router D - Router B = Successfull
Router D - Router E = Successfull
Router E - Router A= Successfull
Router E - Router B = Successfull
Router E - Router C = Successfull
Router E - Router D = Successfull

PEKANBARU, 23 JULI 2019

SISWA 1 SISWA 2 PEMERIKSA (GURU)

RESA NOVITA SARI ElLDIAS FERDIANSYAH LUKMAN, SE,


M.KOM

You might also like