Scribd
Upload
83 views

Step by Step Guide To Setup Active Directory On Windows Server 2008

This document provides a step-by-step guide to setup Active Directory on Windows Server 2008. It outlines the requirements, steps to assign an IP address and install the Active Directory Domain Services role using Server Manager. It then describes configuring the DNS settings and running dcpromo to promote the server to a domain controller for a new forest. The summary installs AD, configures the server as a DNS server, and promotes it to a new domain controller.

Uploaded by

Jennifer Monterey
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
83 views

Step by Step Guide To Setup Active Directory On Windows Server 2008

This document provides a step-by-step guide to setup Active Directory on Windows Server 2008. It outlines the requirements, steps to assign an IP address and install the Active Directory Domain Services role using Server Manager. It then describes configuring the DNS settings and running dcpromo to promote the server to a domain controller for a new forest. The summary installs AD, configures the server as a DNS server, and promotes it to a new domain controller.

Uploaded by

Jennifer Monterey
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 11

Step by Step guide to

setup Active Directory on


Windows Server 2008
MARCH 7, 2011 BY DISHAN M. FRANCIS 154 COMMENTS

This tutorial will explain how to install AD on server 2008. This will valid
for windows 2008 R2 as well.

Requirement:

Minimum: Single processor with 1.4 GHz (x64 processor) or 1.3GHz


(Dual Core)
Minimum: 512 MB RAM
Minimum: 32 GB or greater
 The first step is to assign a ip to the server that you going to deploy
the AD. Its nessary to install it as DNS server too. So its better to
have fixed ip it doesn't mean you cannot install AD without fixed ip
address but it will solve lot of issues if you used fixed ip.

In here the server ip is 10.0.0.14. Since we going to make it as DNS


server too you should use the same ip as the preferred DNS server.
 Next step is to install the Active directory roles. Unlikely the older
version of windows servers Microsoft highly recommend to use server
manager option to install roles before you run dcpromo.

 Click on start menu and select the Server Manager

 Select the roles from the right hand panel and click on add roles
option.

 From the roles list select the "Active Directory Domain Services" role
and Click "Next"
 Review the confirmation and click on "Next"

 Review the installation confirmation and click on "Next"


 It will take few minutes to complete and when its done you will get
this confirmation. And then click on "Close"

After that you will need to do a reboot.

 After reboot please open up the "server Manager" again. And then
click on "Roles" there you will see the "Active Directory Domain
Services" is successfully installed in there. click on it then you will get
a window like below.
In their please pay attention to the message

So please click on that link and it will start the DCPROMO wizard.

 So next step to go through the DC promo wizard.


 To start the installation click on "Next"
 Click on "Next"

 Since we going to install New domain Controller in new forest please


select the option "Create a new domain in new forest" option and
click on "Next"
 Now we have to provide the name for our domain controller. It must
be FQDN. In our case I used rebeladmin.com as the domain. Please
click "Next" after it.

 In this window it will ask to select forest function level. If you going to
add server 2003 domain controller to your forest later don't select the
function level as server 2008. If you going to use full features of 2008
Ad you must select forest function level as server 2008. In my case I
used server 2008. Click on "Next" after the select.

 In next window since it's the first DC we should make it as DNS


server too. Leave the default selection and click on "Next"
 If the wizard cannot create a delegation for the DNS server, it
displays a message to indicate that you can create the delegation
manually. To continue, click "Yes"

 In next window it will show up the database location. It its going to be


bigger AD its good if you can keep NTDS database in different
partition. Click on "Next" after changes.
 In next window its asking to define a restore mode password. Its
more important if you had to do a restore from backup in a server
crash. Click on "Next" after filling it.

 Next window is giving you a brief of the installation. Click on "Next"


 Then it will start the installation of the AD. It will take some time to
complete. After complete of the installation perform a server reboot.

 After the reboot now you can login to the domain. Please use the
login as following example

User name : your domain\administrator

Password : XXXXXXXX

 Now its done and you can view the active directory options on
administrative tools menu

You might also like