Client : AAFAQ HOLDINGS LLC Date : OCT'12

Project : AL AIN STADIUM & MIXED USE Calc'd by : BND

DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 1

CONNECTION NO : 34 ( Typical outer & inner strut end detail to main truss along grid TR-13 to TR-22 in upper -
East flood light gantry walkway , Refer dwg no. AAS-SBP-SUS-STD-R1-DWG-00071 -
Rev.01)
LOADS ( worst case Group no.112 & Element No.1120800 )

Beam (CHS159x7.1)

Axial Fa := 132kN

NOTES:-
All welds are 6mm CFW., U.N.O
All welds shall be Electrode E70XX (or) Equivalent, U.N.O
All Connection plates are ASTM A572 GRADE-50 (or) Equivalent, U.N.O
All Rolled shapes are ASTM A-572 GRADE-50 (or) Equivalent, U.N.O
All Pins are hot dip galvanize as per clause 9.1.5 of Technical Specification

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 2

SECTIONAL PROPERTIES

Bracing B := "CHS 159 x 7.1 "

2
Dbr := 159mm Tbr := 7.1mm Abr := 3390mm

MATERIAL PROPERTIES

N N
Design yield strength of ASTM A572 Fy572 := 345 Tensile strength of ASTM A572 Fu572 := 450
2 2
mm mm

N N
Design yield strength 34 CrNiMo 6 + QT Fy341 := 900 ⋅ Tensile strength of Fu341 := 1100 ⋅
(Mat.-No.1.6582) (EN 10083-3) 2 34 CrNiMo 6 + QT 2
mm mm
(Thickness 16mm ~ 40mm) (Mat.-No.1.6582) (EN 10083-3)
(Thickness 16mm ~ 40mm)

N N
Design yield strength 34 CrNiMo 6 + QT Fy342 := 800 ⋅ Tensile strength of Fu342 := 1000 ⋅
(Mat.-No.1.6582) (EN 10083-3) 2 34 CrNiMo 6 + QT 2
mm mm
(Thickness 40mm ~ 100mm) (Mat.-No.1.6582) (EN 10083-3)
(Thickness 40mm ~ 100mm)

Nominal strength of fillet weld - N

Fvw := 217
for Electrodes E 70XX 2
(ANSI/AISC 360-10 Table J2.5) mm

DIMENSIONAL REQUIREMENTS (ANSI/AISC 360-10,Clause D5.2)

Diameter of Pin d := 40mm

Diameter of Pin Hole dh := d + 2mm dh = 42 ⋅ mm

Thickness of spade plate tsp := 10mm

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 3

Plate Dimension b := 58mm

b(58 mm) > 2tsp+16 (36 mm): Therefore O.K.

Plate Dimension be := 2tsp + 16mm be = 36 ⋅ mm

b (58 mm) > be (36 mm): Therefore O.K.

Plate Dimension a := 59mm

a(59 mm) > 1.33be (47.9 mm): Therefore O.K.

Plate Dimension c := 59mm

(conservatively)

c(59 mm) > a (59 mm): Therefore O.K.

Width of Plate wsp := 179mm

wsp (179 mm) > 2be+d (112 mm): Therefore O.K.

CHECK FOR PIN

Check - Bearing on projected area of pin

Thickness of lug plate tlp := 20mm

2
Area Apb1 := d ⋅ tlp Apb1 = 800 ⋅ mm

Bearing strength Rn1 := 0.75 ⋅ 1.8 ⋅ Apb1 Fy342 Rn1 = 864 ⋅ kN

Rn1 (864 kN) > Fa (132 kN): Therefore O.K.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 4

Check - Shear yielding on the pin

2
π ⋅d 2
Area A1 := A1 = 1256.6 ⋅ mm
4

Double shear yielding capacity Pn1 := 0.9 ⋅ 0.6A1 ⋅ Fy342 ⋅ 2 Pn1 = 1085.7 ⋅ kN

Pn1 (1085.7 kN) > Fa (132 kN): Therefore O.K.

Check - Bending yield line in pin

4
π ⋅d 4
Moment of Inertia Ix := Ix = 125663.7 ⋅ mm
64

Ix
3
Section modulus Zx := Zx = 6283.2 ⋅ mm
d ⋅ 0.5

Moment yielding capacity Mc := 0.9 ⋅ Zx ⋅ Fy342 Mc = 4.5 ⋅ kN ⋅ m

Spacing between Plates s := 2mm

Fa
Maximum moment in pin M1 :=
8
(
⋅ tlp + 4 ⋅ s + 2tsp ) M1 = 0.79 ⋅ kN ⋅ m

Mc (4.5 kN) > M1(0.8 kN): Therefore O.K.

Check - Combined shear & moment

2 2
⎛⎜ Fa ⎞⎟ ⎛ M1 ⎞⎟
Combined shear and moment R := +⎜ R = 0.21
⎜⎝ Pn1 ⎟⎠ ⎜⎝ Mc ⎟⎠

1.0 > R ( 0.21 ) : Therefore O.K.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 5

CHECK FOR SPADE PLATE (ANSI/AISC 360-10,Clause D5.1)

Check - Bearing on the projected area (ANSI/AISC 360-10,Clause J7)

Projected area in bearing Apb2 := d ⋅ tsp ⋅ 2 2

Apb2 = 800 ⋅ mm

Bearing strength Rn2 := 0.75 ⋅ 1.8 ⋅ Apb2 ⋅ Fy572 Rn2 = 372.6 ⋅ kN

Rn2 (372.6 kN) > Fa (132 kN): Therefore O.K.

Check - Shear rupture on the effective area

⎡ ⎛ d ⎞⎤ 2
Area on shear failure path Asf := ⎢2 ⋅ tsp ⋅ ⎜ a + ⎟⎥ ⋅ 2 Asf = 3160 ⋅ mm
⎣ ⎝ 2 ⎠⎦

Nominal shear strength Pn2 := 0.75 ⋅ 0.6 ⋅ Asf ⋅ Fu572 Pn2 = 639.9 ⋅ kN

Pn2 (639.9 kN) > Fa (132 kN): Therefore O.K.

Check - Tensile rupture on the net effective area

Plate dimension be1 := b be1 = 58 ⋅ mm

Net effective area (

Anet := 2be1 ⋅ tsp ⋅ 2) Anet = 2320 ⋅ mm
2

Design tensile strength Pn3 := 0.75 ⋅ Anet ⋅ Fu572

Pn3 = 783 ⋅ kN

Pn3 (783 kN) > Fa (132 kN): Therefore O.K.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 6

Check - Yield on the gross section of the plate (ANSI/AISC 360-10,Clause D2-a)

2
Gross Area Ag := wsp ⋅ tsp ⋅ 2 Ag = 3580 ⋅ mm

Tensile yeilding in the gross section Pn4 := 0.9 ⋅ Ag ⋅ Fy572 Pn4 = 1111.6 ⋅ kN

Pn4 (1111.6 kN) > Fa (132 kN): Therefore O.K.

Check - Buckling capacity (ANSI/AISC 360-10 Clause E3 )

Eff. length of spade plate (max) lg := 150mm K := 1.2

(conservatively)

Eff. width of spade plate wg := 179mm

2
tsp
Min. radius of gyration ry := ry = 2.89 ⋅ mm
12

K ⋅ lg N E
5
Slenderness ratio λyy := λyy = 62.35 E := 2.05 ⋅ 10 Cc := 4.71 Cc = 114.8
ry 2 Fy572
mm

2
π ⋅E N
Elastic critical buckling stress Fe := Fe = 520.4 ⋅
2 2
λyy mm

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 7

N
Compressive strength Fcr := 0.877 ⋅ Fe if λyy > Cc Fcr = 261.4 ⋅
2
mm
⎛ Fy572 ⎞
⎜ ⎟
⎜ Fe ⎟
⎝ 0.658 ⎠ ⋅ Fy572 otherwise

Compression capacity Pc := Fcr ⋅ wg ⋅ tsp ⋅ 0.9 ⋅ 2 Pc = 842.2 ⋅ kN

Pc (842.2 kN) > Fa (132 kN): Therefore O.K.

Weld - Spade plate & CHS

Slot Length ls := 175mm

Length of Weld Lw := 4 ⋅ ls Lw = 700 ⋅ mm

Fa kN
Shear per mm on weld FL := FL = 0.1 ⋅
2Lw mm

FL
Size of fillet weld reqd. s reqd := s reqd = 0.62 ⋅ mm
0.7 ⋅ Fvw

Adopt 6mm CFW

CHECK FOR LUG PLATE (ANSI/AISC 360-10,Clause D5.1)

Check - Bearing on the projected area (ANSI/AISC 360-10,Clause J7)

Projected area in bearing Apb3 := d ⋅ tlp 2

Apb3 = 800 ⋅ mm

Bearing strength Rn3 := 0.75 ⋅ 1.8 ⋅ Apb3 ⋅ Fy572 Rn3 = 372.6 ⋅ kN

Rn3 (372.6 kN) > Fa (132 kN): Therefore O.K.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 8

Check - Shear rupture on the effective area

⎛ d⎞ 2
Area on shear failure path Asf1 := 2 ⋅ tlp ⋅ ⎜ a + ⎟ Asf1 = 3160 ⋅ mm
⎝ 2⎠

Nominal shear strength Pn5 := 0.75 ⋅ 0.6 ⋅ Asf1 ⋅ Fu572 Pn5 = 639.9 ⋅ kN

Pn5 (639.9 kN) > Fa (132 kN): Therefore O.K.

Check - Tensile rupture on the net effective area

Plate dimension be2 := b be2 = 58 ⋅ mm

2
Net effective area Anet1 := 2be2 ⋅ tlp Anet1 = 2320 ⋅ mm

Design tensile strength Pn6 := 0.75 ⋅ Anet1 ⋅ Fu572

Pn6 = 783 ⋅ kN

Pn6 (783 kN) > Fa (132 kN): Therefore O.K.

Check - Yield on the gross section of the plate (ANSI/AISC 360-10,Clause D2-a)

2
Gross Area Ag1 := wsp ⋅ tlp Ag1 = 3580 ⋅ mm

Tensile yeilding in the gross section Pn7 := 0.9 ⋅ Ag1 ⋅ Fy572 Pn7 = 1111.6 ⋅ kN

Pn4 (1111.6 kN) > Fa (132 kN): Therefore O.K.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 9

Check - Buckling capacity (ANSI/AISC 360-10 Clause E3 )

Eff. length of gusset (max) lg := 150mm K := 1.2

(conservatively)

Eff. width of gusset wg := 250mm

(conservatively)

2
tlp
Min. radius of gyration ry := ry = 5.77 ⋅ mm
12

K ⋅ lg N E
5
Slenderness ratio λyy := λyy = 31.18 E := 2.05 ⋅ 10 Cc := 4.71 Cc = 114.8
ry 2 Fy572
mm

2
π ⋅E N
Elastic critical buckling stress Fe := Fe = 2081.6 ⋅
2 2
λyy mm

N
Compressive strength Fcr := 0.877 ⋅ Fe if λyy > Cc Fcr = 321.9 ⋅
2
mm
⎛ Fy572 ⎞
⎜ ⎟
⎜ Fe ⎟
⎝ 0.658 ⎠ ⋅ Fy572 otherwise

Compression capacity Pc := Fcr ⋅ wg ⋅ tlp ⋅ 0.9 Pc = 1448.5 ⋅ kN

Pc (1448.5 kN) > Fa (132 kN): Therefore O.K.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation
 Client : AAFAQ HOLDINGS LLC Date : OCT'12
Project : AL AIN STADIUM & MIXED USE Calc'd by : BND
DEVELOPMENT PHASE 1.1 Checked by : JKG
Job No. : F900
Sheet no : ROOF / 34 / 10

CHECK FOR BRACE BAR

Check - Shear capacity of wall

2
Av := ls ⋅ Tbr ⋅ 8 Av = 9940 ⋅ mm
Shear area of wall

shear capacity of wall ( )

Fsw := min 0.6 ⋅ Fy572 ⋅ Av , 0.45 ⋅ Fu572 ⋅ Av Fsw = 2012.9 ⋅ kN

Fsw (2012.8 kN) > Fa(132 kN): Therefore O.K.

Weld - Gusset plate & Beam

Weld Length ls1 := 250mm

Fa kN
Tension per mm on weld FT := FT = 0.3 ⋅
2ls1 mm

FT
Size of fillet weld reqd. s reqd1 := s reqd1 = 1.74 ⋅ mm
0.7 ⋅ Fvw

Adopt 6mm CFW

By inspection, All other checks are O.K for adopted detail.

Variation no: Rev. / Date Description

1 / JAN'13 Client comment Incorporation