2017 International Conference on Communication, Control, Computing and Electronics Engineering (ICCCCEE), Khartoum,

Sudan

Design of Bus Tracking and Fuel Monitoring

System
Safa Abd elmonem. Yosif Murtada Mohamed Abdelwahab Mohamed Abd Elrahman ALagab
University of Gezira University of Gezira Gisco IT Training Center
Gisco IT Training Center Khartoum, Sudan Ajap @giscoit.com
Khartoum, Sudan [email protected] Fares Muhammad
[email protected] Gisco IT Training Center
[email protected]

Abstract—The need for efficient public transportation system designed using ASP.MVC desktop edition to enable the owner
such as buses is rapidly increased due to the increasing in to view the fuel level and the current in location of the buses
population, the passengers need to know the accurate arrival in the map.
time of the particular bus to particular station and then plan
their journey from their home .Fuel monitoring have been the II. RELATED WORK
major problem that most of bus companies looking to solve. This Around the world numerous vehicle tracking systems are
paper developed a bus tracking and monitoring the fuel and being developed. These systems are included in many public
speed system to provide a facility for the management and private vehicles in urban areas.
requirements by the administrator. The proposed system based
on Arduino, GSM/GPS and map suit ASP.MVC which provide
the actuated arrival time in addition to graphically showing the Shruti Kotadiaa [1]: presents a design depend on the using
bus location on Google map. The design also enables the owner of RFID stickers which installed on every bus, these stickers are
the buses to monitor the bus instantaneously because the system installed for identification at bus terminals. Every bus stop is
administrator can easily maintained database information of
assigned by a unique ID, this unique ID is transmitted around
buses and its fuel tank at any time of the service.
Keywords— bus track; MVC; Arduino; GPS; GSM; Fuel. some distance around it RF transmitters and when the RF
receiver on the bus comes within the range of the transmitters,
it will receive signal that is generated by bus stop and it will
I. INTRODUCTION indicate the passengers the next stop.
The bus tracking system is a cost effective and efficient Abid Khan [2]: proposed a design depend on the embedded
system, at the bus station people have to wait for long time system which is a single board system having GPS and GSM
without even knowing when the bus will arrive, the modems and ARM processor to track vehicle. This system has
passengers, can't find the time of arrival of particular bus at large capability, low operation cost, strong expansibility.
the particular destination even at their homes and plan their Madhu Kumar, K. Rajashekhar, et al [3]: proposed, Design of
journey accordingly. The proposed system present the bus punctuality enhanced bus transportation system using GSM
arrival time prediction and fuel monitoring system that and zigbee. In this way service quality of operational
provide the accurate arrival time and bus view to the efficiency is improved and passenger is also able to get the
passengers ,and provide bus monitoring, schedule information about the respective bus
management and fuel monitoring to the bus company owner . Manini Kumbhar1, Meghana Survase [4]: proposed real time
Fuel level detection circuit calculates the fuel level from the web based bus tracking system given to remote user who want
fuel gauge which is present in all the vehicles the current to know the real time bus information. Some technologies like
position of the vehicle was acquired by Global Position GPS (Global Positioning System), Google maps and GPRS
System (GPS) receiver. The Arduino collect the data from fuel (General Packet Radio Service) are used for development
sensor, GPS and speed sensor send it to the server at the base purpose.
station using GSM. Ravi, Rohitaksha [5]. Propose a City Bus location and route
The data at server side are stored in a database tables witch navigation system using smart phones by using ICT
designed to and can be retrieved as request for position (Information and Communication Technology).
browsing on map. A web site is developed using ASP.MVC All previous studies mentioned above talked about Vehicle
web edition, Visual a Studio2013 with embedded Google Map tracking, but each of them have drawbacks, for example the
to retrieve and display on track details. A desktop GUI is RFID technology need another device at the bus stop in
addition of the short rang The passengers cannot get the exact

978-1-5090-1809-3/17/$31.00 ©2017 IEEE

location of the bus, they will only be notified when the buses of buses to the user and he/she can select the station where he
are nearing the user, and other system not track the location on stopping and the rout want to go. After that all buses that
the map. This paper based on the GPS and GSM to design belongs to the require rout and the time that will take to reach
simple, accurate, less used of complex circuit, power the user station will display. Figure.2 and figure.3 illustrate the
consumption and costless bus tracking and fuel monitoring flow chart of the system.
system used Arduino and map suit Asp.MVC technologies.
III. METHODOLOGY
The architecture of the system in this paper is shown in
fig.1. It provides the bus arrival time depending on the user
source and destination. The overall outcomes functionality of
the system comes from the interaction between the system
components, which are a device on the bus, web application
and desktop application. A device on the bus consist of
Arduino, GPS, GSM, fuel sensor and speed sensor. The GPS
receive the coordinate information from satellites and send it
the Arduino, the fuel and speed sensors used to measure the
speed and fuel level and send it to the Arduino, which collect
all this data and send it to the server through the GSM.

Fig.2. Sending Massage at the Bus Unit

Fig.1. Architecture of proposed system

The device in the bus send a frame to the pc in the central

station (server) .that frame consist of speed, location of the bus
and its fuel level. The pc stores this information in the
database in order to view it in the desktop application or web
application.
There are GSM module at the server side used to receive
the information from the buses and store it in the database. All
information about the buses, drivers, stations and routes are
also stored in the database and the owner able to delete, update
and enter new information Fig.3. Mapping the Bus Location on the Google Map
Once the information is uploaded in the server the
The components and programs that used are:
commuter can access the information via the web site using
internet .The ASP.MVC and visual studio 2013 with embedded
of Gogol map are used to design the web site that provide view
A. GPS TECHNOLOGY C. Arduino mega 2560
The global positioning system (GPS) is a satellite-based
The Arduino mega 2560 as shown in Figure3.6is a
navigation system consists of a network of 24 satellites located
microcontroller board based on the ATmega2560. It has 54
into orbit as shown at figure 2.3. The system provides
digital input/output pins (of which 14 can be used as pwm
essential information to military, civil and commercial users
outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a
around the world and which is freely accessible to anyone
16 MHz crystal oscillator, a USB connection, a power jack,
with a GPS receiver. GPS works in any weather circumstances
and a reset button. It contains everything needed to support the
at anywhere in the world. Normally no subscription fees or
microcontroller; simply connect it to a computer with a USB
system charges to utilize GPS. A GPS receiver must be locked
cable or power it with an AC-to-DC adapter or battery to get
on to the signal of at least three satellites to estimate 2D
started. The reasons of using the Arduino board which comes
position (latitude and longitude) and track movement. With
with ATmega168 or 328 for easy interfacing with the GPS and
four or more satellites in sight, the receiver can determine the
GSM module and for easy programming (in C) of the
user's 3D position (latitude, longitude and altitude). Once the
microcontroller. The Arduino boards come with a library for
vehicle position has been determined, the GPS unit can
interfacing with module and for dealing with analog or digital
determine other information like, speed, distance to
inputs and outputs [6].
destination, time and other. GPS receiver provides data in
NMEA 0183format with a 1Hz update rate. Generally
message received by GPS is in National Marine Electronics
Association (NMEA) message format and NMEA protocol
which is most commonly used is NMEA0183 protocol. GPS
sentences beginning with the following specifications:
$GPGGA, $GPGSA, $GPGSV, $GPRMC, and $GPVTG
And sentences also begins with $GPMSS, $GPZDA.
Fig.6. Arduino Mega 2560 [6]

D. ASP .NET MVC

It is an alternative to ASP .NET Web Forms it is short of
Model View Controller. The Models (Business/domain logic)
Model objects, retrieve and store model state in a persistent
storage (database). The Views display application’s UI that
Fig.4. GPS Module created from the model data. The Controllers handles user
input and interaction, work with model and select a view for
B. GSM module rendering UI.
The GSM modem is a specialized type of modem which
accepts a SIM card operates on a subscriber’s mobile number IV. RESULTS AND DISCUSSIONS
over a network, just like a cellular phone. It is a cell phone First all the devices in the buses send a frame to the central
without display. station every 5 second through GPRS network using the GSM
module. In the central station when the designed program is
executed, main Form in the desktop application is displayed
to perform the following:
• Setting the baud rate and the com of the GSM that
connect with the central computer to open the
connection with the bus
• When the connection establish the GSM receive the
information from the buses and send it to the desktop
application to store it in the database .this process occur
in background.
• In figure_6 in the Setting section in the right side, if you
press any button that Labels with a Buses, Drivers,
Stations or Routs, the sub screen will appear as shown
in the figures from 8 to 11, throw it the administrator
can add or remove a buses, station, rout or driver
information from the database.
Fig.5. GSM module
 Fig.9. Update Station Information.

Fig.7. Desktop Application.

Fig.10.Update bus Information.

Fig.8. Update Driver Information

Fig.11.Update routes Information

 When the user enters the web site a screen will appears as give the accurate arrival time of the bus and provide the
shown in fig.12. location of the bus in Google map for both user and
administrator. This system reduces the waiting time of remote
users for bus and provides bus tracking at any location,
management and fuel monitoring.

ACKNOWLEDGMENT
The author are very grateful to DR. MURTADA for his
kindness and precious help and the coworkers in GISCO-IT
epically Mr. Fares Mohamed and Mr. Mohamed Alagab for
their help.
REFERENCES

[1] S.Kotadia, “RFID based tracking system”, International Research

Journal of Engineering and Technology (IRJET), Volume: 02 Issue: 06 |
Sep-2015.
[2] S. Gharge, M.Chhaya, G. Chheda and J. Deshpande, “Real time bus
monitoring system using GPS,” An International Journal of Engineering
Science and Technology, Vol. 2, Issue 3, June 2012.
[3] M. Manikya Kumar, K. Rajesekhar, K. Pavani, “Design of punctually
enhanced bus transportation system using GSM and Zigbee,”
International Journal of Research in Computer and Communication
Technology, Vol. 2, Issue 12, December 2013.
[4] M. Kumbhar1 and Meghana,” Real Time Web Based Bus Tracking
System”, International Research Journal of Engineering and Technology
Fig.12. The Web Site (IRJET) Volume: 03 Issue: 02 | Feb-2016.
[5] Ravi and Rohitaksha, “an Innovative Approach for City Bus Location
The user must the select station and the rout of the bus that with Route Navigation System using Android”, European Journal of
want to go and all the buses that belong the rout witch selected Advances in Engineering and echnology, 2015, 2(3): 38-45.
will appear in the map in the middle of the screen and time that [6] Kainka, F. D. Franzis,”Starterpaket Arduino Mega 2560”. Haar: Franzis
need to reach the station Verlag. , December 2013.

V. CONCLUSION
This paper offers a smart design of tracking and
monitoring the busses which helps the bus companies to
provide high quality of service. This design can provide the
location of the busses of the service with an error less than 10m
in the case of slow speed and clear environment and the system