TC- 515

Temperature/ Process Controller

Features and Benefits
· User friendly installation and operation.
· Easy configuration via a simple text based function menu.
· Dual 3 Digit Display for simultaneous indication of both process temperature and
setpoint.
· Selectable PID, ON/OFF or Trip and Recovery Control modes.
· PID control with Autotune function ensures precision control.
· Full Autotune for PID control, calculating P, I, D, and Anti-reset wind-up terms.
· Adjustable PID relay cycle time for precision control of fast or slow processes.
· Adjustable ON/OFF control hysteresis, allowing greater flexibility when controlling
non-critical processes.
· Trip and Recovery control mode allows two independently adjustable trip and
Recovery levels with separate control outputs.
· Two independently programmable temperature alarm levels can be used in 12
different modes and are selectable as an upper alarm level, a lower alarm level or
both. They can also be configured to operate as absolute or deviation standby alarm
levels.
· Keypad programmable for use with any one of 9 commonly used temperature
sensors.
· Programmable relay action for heating or cooling applications to ensure fail-safe
operation.
· Programmable operation in degrees Celsius or degrees Fahrenheit.
· A process protect feature , which when enabled, confines the setpoint to a range
determined by the two alarm levels and prevents accidental changes of the setpoint to
outside the alarm limits.
ORDERING CODE · Programmable process temperature offset that can be set to the difference between
POWE R
the process and sensor temperatures. This is used when the sensor cannot be
INPUT OUTPUT
MO DEL TYPE SUPPLY TYPE positioned ideally.
· A unique 16 hour timer for batch processing.
· Keypad lock security feature to prevent unauthorised adjustments by providing three
TC515 U0 024E RR levels of security.
· An 8 Amp relay or SSR (Solid State Relay drive) output.
· Analogue and digital input filtering.
· A plug connector system that allows quick and easy installation.
· Multi-voltage (21-53V AC/DC, 85-265V AC/DC).
· Digitally calibrated.
· Mark.

Description of Operation
The Basics of ON/OFF Control temperatures. Unfortunately, the process temperature only settles at the setpoint if
In this simple form of control, the controller output switches off when the process the heat source (heater) matches the heat load of the process EXACTLY. Heaters
temperature reaches the setpoint. The process cools until the recovery level is and processes are rarely matched and therefore the process temperature usually
reached and power is re-applied to the process. The resulting process temperature settles at a value offset from the setpoint as shown in Fig. 3.
oscillates through this hysteresis band (the band between setpoint and recovery
levels) as illustrated in Fig. 1. On/Off Control is ideal for large capacity processes Proportional and Integral Control (PI)
(processes that have slow temperature changes and are insensitive to To compensate for the offset resulting in proportional only control, a second control
disturbances) because the hysteresis band can be set very narrow, minimising term known as Integral Action is introduced. Integral Action eliminates the offset by
temperature oscillations. responding to duration of the error signal (through integration) and automatically
Example: The thermostat of a household heater uses On/Off control. When the forcing the process temperature to settle exactly at the setpoint after a period of time
room temperature reaches the setpoint, a switch opens and turns the heater off. The (as shown in fig. 4). This is achieved by small adjustments in the proportional output.
switch remains off until the room temperature drops below the setpoint causing the
switch to close, turning the heater on again. The heater is either ON or OFF. Proportional, Integral and Derivative Control (PID)
In many small capacity processes, the controller must respond quickly to large and
The Basics of Trip & Recovery Control rapid changes in temperature caused by disturbances. Derivative action provides
Trip and Recovery mode facilitates control of two independent setpoints. In heating, additional temperature stability by reacting to the rate of change of the process
each trip point represents the temperature above which the relay is de-energised temperature.
and the heating mechanism is de-activated. The recovery points represent a Example: An injection moulding machine benefits from PID control. Proportional
temperature below which the relay is re-energised and the heating mechanism is control ensures that the plastic temperature is stable and does not oscillate. Integral
turned on. This feature can also be used in cooling applications. Each trip point will control maintains accuracy by keeping the temperature exactly at the setpoint over
then represent the temperature below which the relay is de-energised and the long periods. Derivative action forces the temperature back to the setpoint quickly
cooling mechanism is de-activated. The recovery points represent the temperature when the cold plastic pellets enter the melting chamber.
above which the relay is re-energised and the cooling mechanism is turned on.
Example: A typical application where two fans are used to control a process is Autotune Function
shown in Fig. 2 above. The first fan is activated at 300° and remains on until the For optimum PID control, the controller parameters (P, I and D values) should be
temp. falls below 250°, while the second switches on at 350° and switches off at tuned for each temperature process. This can be performed manually or
280°. automatically by activating the Autotune function. PID control facilitates precision
control at the setpoint temperature (as shown in fig. 5) and the Autotune function
The Basics of PID Control makes the unit easy to set up.
In applications where precision control is required, including small capacity
processes that react quickly to disturbances, it is necessary to provide a more Anti-Reset Wind-Up
sophisticated method of temperature regulation than that of ON/OFF control. For Anti-reset wind-up, sometimes referred to as manual reset, is automatically
example, ON/OFF control would be ineffective in controlling the temperature of a calculated during the Autotune function but can also be manually set, if required. It is
bathroom shower as the person would be subjected to alternative bursts of HOT and used in conjunction with proportional, integral and derivative terms to speed up the
COLD water, neither of which is desirable. It is necessary to establish a proportion of time it takes a process to reach its setpoint temperature while minimising overshoot.
hot to cold water to maintain the required temperature. This term represents the percentage power that a proportional only system would
require to maintain its setpoint temperature.
Proportional Control (P)
Proportional control provides added temperature stability by eliminating Example: A user would set the anti-reset term to 30 for a system requiring 30%
temperature fluctuations by setting the proportion of power supplied to the process power to maintain its setpoint temperature.
depending on the difference between process and setpoint

REC2 350°
SETPOINT REC1 300°
TEMPERATURE

} } OFFSET SETPOINT
TEMPERATURE
TEMPERATURE
TEMPERATURE

TRIP2 280°
SETPOINT SETPOINT
TRIP1 250°
HYSTERESIS
TIME
RELAY 1
TIME TIME TIME
TIME
RELAY 2
Figure 1 Figure 2 Figure 3 Figure 4 Figure 5
 Precision Measures Perfection

TEMPERATURE / PROCESS CONTROLLERS

Description of Controls

THERMOLINE
1. Process Value Display: 3 digit display of process temperature or function name.

2. Set Value Display: 3 digit display of setpoint or function status.

1
3. Control LED: Control output status indication. Control LED illuminates when control
CONTROL output is energised.
3 ALARM 2 4. Alarm LED: Alarm output status indication. Alarm LED illuminates when alarm
4 output is energised.
5 6 5. Select Keys: Press to move up or down the function list.
TC515 TEMPERATURE CONTROLLER
6. Up/Down Keys: Press to change the setpoint value or the status of the displayed
function. Hold down to scroll quickly.

Wiring and Connection

Wiring: Examples on how to connect the Controller.

L L
Fast-Blow
Fuse See Note**
Fast-Blow
Fuse 1 4

+
+ -
Heater Thermocouple Controlled -
Alarm SSR 230V System 3
220V AC/DC 2
Relay 230V 8A 3-Wire PT100 Heater Solid State
AC/DC Sensor Input 220V Relay 25A
Sensor
Sensor Input Controlled Alarm 20A
TC515
+ -
System 220V 5A
TC515

N N
Example 1: Controller with Relay Output, no alarm required. Example 2: Controller with Solid State Relay (SSR)
Input is from a thermocouple. Output and Relay Output for Alarm.
Input is from a PT-100 RTD.

** Note: It is recommended that a Slave Relay/Contactor be installed when switching large inductive/ resistive loads

Technical Specifications
Controller Specifications EMC Protection Rating General Specifications
Setting Accuracy ± 1% Radiated Susceptibility IEC 801-3, Class 3 Operating Temperature 0 - 50°C
Linearisation Accuracy ± 0.3% Radiated Emission CISPR11, Class B Humidity 5-85% non-condensing
Cold Junction Tracking 0.05°C per °C Conducted Susceptibility IEC 255-22-1, Class II Storage Temperature -20°C to 70°C
Sampling Period 70ms Conducted Emission CISPR11, Class B Protection Class (Front) IP54
Protection Class (Rear) IP30
Control Method PID, On/Off or Trip & Rec.
PID Relay Cycle Period 1-240secs
Control Output Options Connection Plug-connector
Relay 250V AC, 8A, SPDT Weight 250g
On/Off Control Hysteresis 0-99.9°
SSR Drive 8-28V DC at 10mA Standards CE Mark
Proportional Band 0,5°-999º Creepage Distance VDE 0110 (Group C 250V)
Integral Time 0-999 seconds IEC 664/664A
VDE 0435
Derivative Time 0-999 seconds
Timer Range 1-999 minutes Alarm Output Options Power Supply
Timer Accuracy 0.1% of preset time Relay 250V AC, 8A, SPST (N.O) Power Supply 21-53V AC/DC
SSR Drive 8-28V DC at 10mA 85-265V AC/DC
Timer Resolution 1 minute
Power Consumption Less than 3VA

Input Specifications: Temperature Sensors Display Specifications

Operating Sensor Type PV Display Type 3 x 10mm red
Temperature PT100 E J K R S T B N SV Display Type 3 x 7mm green
Upper Limit ºC 800 950 750 999 999 999 380 999 999 Resolution (PV, SV) 1° (SV 0,1º from
ºF 999 999 999 999 999 999 715 999 999 -9,9º to 99,9º)
Lower Limit ºC -99 -99 -99 -40 -40 -40 -99 50 -99 Temp. Display Range -99º to 999°
ºF -99 -99 -99 -40 -40 -40 -99 122 -99
Note: In some cases the sensor range is limited by the display range of the controller (-99° to 999°).
For operation over a wider temperature range see TC600/ PC100.

For more info: www.rhomberg.co.za