Surface Prep / TDS-108

LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment
1 Product Name
LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment

2 Manufacturer
Custom Building Products
13001 Seal Beach Blvd.
Seal Beach, CA 90740-2757
Customer Support: 800-272-8786
Technical Services: 800-282-8786
Fax: 800- 200-7765
Email: [email protected]
custombuildingproducts.com
Composition of Product
3 Product Description
Helps level floors prior to the installation of ceramic tile, natural stone, LevelQuik© is a proprietary dry blend of copolymers, cements, and
resilient flooring, carpet, wood and other floor coverings. This quick- inorganic chemicals.
setting underlayment can be applied to 1.5" (3.8 cm) thick in one pour Benefits of Product in the Installation
and seeks its own level in minutes. With proper installation, the use of
LevelQuik® RS can achieve an extra heavy rating for high impact use Can be applied from feather edge to 1.5" (3.8 cm) thick in a single
in food plants, dairies, breweries and kitchens. LevelQuik RS may be pour
applied to in residential structures with floor joists up to 24" o.c. Reduces bond failure and crumbling of resilient flooring
Formulated using Controlled Cure Technology®, LevelQuik RS helps
Cures fast and develops high early strength for quick installation
eliminate installation problems such as bond failure, crumbling and
staining of resilient flooring caused by the free moisture found in Rated for Extra Heavy use per ASTM C627
traditional underlayments. Rated for Residential use over wood subfloors with joists to 24" (61
cm) per ASTM C627
Key Features

Seeks its own level in minutes Limitations to the Product

Levels from feather edge to 1.5" in one pour For interior use only.
Walkable in 4 hours Do not bond directly to hardwood, Luan plywood, particle board,
Exceeds TCNA requirements for ceramic tile installations parquet, cushion or sponge-back vinyl flooring, metal, fiberglass or
plastic. Contact CUSTOM technical services for recommendations.
Uses
Do not use when the temperature is below 50°F (10°C) or above 90°F
Suitable as an Underlayment for: (32°C).
Vitreous, semi-vitreous or non-vitreous tile Do not use as a permanent wear surface.
Ceramic, mosaic or quarry tile Do not use on sloped surfaces that require drainage.
Impervious porcelain and glass tile Precautions should be taken when applying over post-tensioned
Cement-based precast terrazzo concrete, pre-stressed concrete or prefabricated concrete planks.
Natural stone tile Contact CUSTOM technical services for further details.
Carpet For installations over metal decks, contact CUSTOM technical services
Wood, parquet for recommendations.
Vinyl composition tile (VCT)
Packaging
Sheet vinyl flooring
Laminated flooring 50 lb (22.68 kg) bags

Suitable Substrates 4 Technical Data

Applicable Standards
Absorbent concrete
Non-absorbent concrete ASTM International (ASTM)
Lightweight concrete
Gypsum-based underlayments
Existing ceramic tile
Cement terrazzo
Exterior grade plywood
OSB
Cutback adhesive residue
Prepared VCT

Published Date: 11/14/2014

 Surface Prep / TDS-108

LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment
ASTM C1708 Standard Test Methods for Self-leveling Mortars Bonding to Concrete Surfaces
Containing Hydraulic Cements Contaminants or curing compounds should be mechanically
ASTM C627 Standard Test Method for Evaluating Ceramic Floor Tile removed before installation. Concrete must be free of efflorescence
Installation Systems Using the Robinson-Type Floor Tester and not subject to moisture beyond the floor covering manufacturers'
ASTM F1869 Standard Test Method for Measuring Moisture Vapor limits or hydrostatic pressure. Lightweight concrete surfaces must have
a tensile strength in excess of 200 psi (1.4 n/mm²).
Resilient Floor Covering Institute (RFCI) Recommended Work Practices
Bonding to Plywood Surfaces
for Removal of Resilient Floor Coverings
Tile Council of North America (TCNA) TCNA Handbook for Ceramic Tile Plywood floors, including those under resilient flooring, must
Installation, TCNA Method EJ171 be structurally sound and must meet all industry guidelines. A 2.5
American National Standards Institute (ANSI) ANSI A108.01 lb/yd² metal lath must be fastened every 6" ­ 8" (15 ­ 20 cm) with
and A108.02 of the American National Standards for the Installation fasteners that have a galvanized or corrosion-resistant coating over
of Ceramic Tile primed surface. A minimum of a 1/2" pour is required for single layer
plywood; for multi-layered plywood, the lath must be fully
Technical Chart
encapsulated. For questions about proper subfloor installation, call
Custom Technical Services.
Property Test Method Typical Results
OSB Underlayments
Pot Life 15 minutes
Flow Time 18 minutes OSB underlayments should be coated with 10-15 mils of RedGard®
Waterproofing and Crack Prevention Membrane prior to priming
Compressive Strength at 28 days ASTM C-109 >4,000 psi
with LevelQuik Latex Primer. A 2.5 lb/yd² metal lath must be fastened
Flexural Strength at 28 days ASTM C-109 >800 psi (5.5 MPa) every 6" - 8" (15 - 20 cm) with fasteners that have a galvanized or
Walkable Hardness 2 - 4 Hours corrosion-resistant coating. A minimum of 1/2" (12.7 mm) of LevelQuik
RS can be applied over this properly prepared OSB.
Robinson Test ASTM C627 Extra Heavy
Time Before Installing Floor Covering Bonding to Gypsum Surfaces
Ceramic Tile > 4 Hours Gypsum-based underlayments must obtain a minimum 2000 psi (13.8
Other Floor Covering > 16 Hours MP) compressive strength. The underlayment must be sufficiently dry
and properly cured to the manufacturer’s specifications for permanent,
Environmental Consideration non-moisture permeable coverings. Surfaces must be structurally
sound and subject to deflection not to exceed the current industry
Custom® Building Products is committed to environmental standards. Surfaces shall be free of all grease, oil, dirt, dust, curing
responsibility in both products produced and in manufacturing compounds, waxes, sealers, efflorescence, or any other foreign
practices. Use of this product can contribute towards LEED® v3 matter.
certification:
All Gypsum surfaces should be primed with a properly applied sealer
Up to 2 points towards MR Credit 5, Regional Materials or a primer coat of RedGard, consisting of 1 part RedGard diluted with
4 parts clean, cool water. Mix in a clean bucket at low speed to obtain
5 Instructions a lump-free solution. The membrane can be brushed, rolled or
General Surface Prep sprayed to achieve an even coat. Apply the waterproofing coat to the
floor at a rate of 300 sq. ft.l (7.5 sq. m/L). Drying time depends on site
USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when conditions, but is normally less than 1 hour. Extremely porous surfaces
handling product. may require 2 coats. At this point, LevelQuik Latex Primer and
LevelQuik RS can be applied to the primed lightweight or gypsum
All surfaces must be structurally sound, clean, dry and free from
based surface. Refer to the individual product data sheet or packaging
contaminants that would prevent a good bond. Concrete must be fully
directions for application instructions. Expansion joints must be
cured. Concrete surfaces should be primed with LevelQuik Latex
installed in accordance with local building codes and industry
Primer. Smooth concrete surfaces, existing glazed tile, terrazzo, or
guidelines.
polished stone may need to be roughened or scarified. For increased
performance in demanding applications, concrete surfaces can be
mechanically profiled and prepared by shotblasting, sandblasting,
water-jetting, scarifying, diamond-grinding or other engineered
approved methods (reference ICRI CSP 3 standards for acceptable
profile height). CUSTOM's MBP Multi-Surface Bonding Primer may be
used as an alternative to profiling the surface.

Block penetrations in the substrate and walls to prevent leveler from

flowing into adjoining rooms. Perimeter space, created with foam
strips or by other means, may be required over suspended slabs when
product is applied in thick applications.

Published Date: 11/14/2014

 Surface Prep / TDS-108

LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment
Bonding to Cutback Adhesive Curing of Product

Adhesive layers must be removed. Use extreme caution; Install non-moisture-sensitive ceramic tile or stone in 4 hours;
adhesives may contain asbestos fibers. Do not sand or grind adhesive most floor coverings can be installed after 16 hours. Drying time can
residue, as harmful dust may result. Never use adhesive removers or vary with temperature and humidity. Test for moisture content
solvents, as they soften the adhesive and may cause it to penetrate before applying vinyl or wood flooring to the surface of the self-
into the concrete. Adhesive residue must be wet-scraped to the leveling underlayment.
finished surface of the concrete, leaving only the transparent staining
Cleaning of equipment
from the glue. To determine desirable results, do a test bond area
before starting. Refer to the RFCI Pamphlet "Recommended Work Clean with water before the material dries.
Practices for Removal of Resilient Floor Coverings" for further
information. Health Precautions

Priming This product contains Portland cement. Avoid eye contact or prolonged
contact with skin. Wash thoroughly after handling. If eye contact
Prime all surfaces with LevelQuik Latex Primer or appropriate surface occurs, flush with water for 15 minutes and consult a physician. Use
primer before application. with adequate ventilation; do not breathe dust and wear a NIOSH
approved respirator. If ingested, do not induce vomiting; call
Joints or Cracks in Substrate
a physician immediately.
Expansion joints and cold joints, as described in ANSI A108.01, should Conformance to Building Codes
be carried from the substrate up through the tile or flooring surface
and filled with an appropriate elastomeric sealant, such as Custom's® Installation must comply with the requirements of all applicable local,
100% Silicone Caulk. For the proper treatment of control or saw cut state and federal code jurisdictions.
joints and cracks for flooring, refer to ASTM F710. For tile installations,
refer to TCNA Details EJ171, F125 & F125A. Contact Custom's® 6 Availability & Cost
Technical Services for additional information.
Location Item Code Size Package
Movement Joint Placement
USA LQ50 50 lb (22.68 kg) Bag
Movement joints are required for perimeters and other changes of Canada CLQ50 50 lb (22.68 kg) Bag
plane in all installations. See TCNA Detail EJ171 for recommendations.

Mixing Ratios 7 Product Warranty

Custom® Building Products warrants to the original consumer
Mix the entire 50 lb (22.68 kg) bag of powder with 5.25 - 5.75 quarts
purchaser that its product shall be free from defects in material and
(5 - 5.4 L) of clean, cool water.
workmanship under normal and proper usage for a period of one year
Mixing Procedures following the date of original purchase. Custom's® sole liability under
this warranty shall be limited to the replacement of the product. Some
Mix 50 lb. (22.68 kg) bag of powder with the appropriate amount
states, countries or territories do not allow the exclusion or limitation
of clean, cool water. Slowly add powder to water while mixing with
of incidental or consequential damages, so the above limitation or
a heavy­duty 1/2" (13 mm) electric drill and an “egg­beater”
exclusion may not apply to you. This warranty will not extend to any
mixing paddle at minimum 650 RPM. Thoroughly mix for 2 minutes to a
product which has been modified in any way or which has not been
lump-free consistency. Do not overmix. Overmixing or moving the
used in accordance with Custom's® printed instructions. Custom®
mixer up and down during the mixing process could trap air, which
makes no other warranties either expressed or implied. This warranty
could shorten the pot life or cause pinholing during application and
gives you specific legal rights, and you may have other rights that vary
curing.
from state to state or from one country/territory to another. This
Application of Product warranty is not transferrable.

Apply LevelQuik Latex Primer according to the specifications on its When LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment is

technical data sheet prior to the application of LevelQuik RS. used as a part of a qualifying full installation system of CUSTOM
products, the installation can qualify for up to a lifetime system
Pour LevelQuik RS, then spread with a long-handled gauged spreader. warranty. CUSTOM will repair and/or replace, at its discretion, the
LevelQuik RS will seek its own level during the first 20 minutes. For affected area of the system. For more information, find details and
featheredging and touch-ups, use a smoothing tool. Can be applied up limitations to this warranty at custombuildingproducts.com.
to 1.5" (3.8 cm) thick in one application. If a second layer is required,
install immediately after the first layer has set to a walkable hardness. 8 Product Maintenance
If the first layer has dried over 12 hours, re-prime before second
Properly installed product requires no special maintenance.
application. The surface will dry to a walkable hardness in 2 - 4 hours.
LevelQuik® RS is not recommended as a finish or wear surface.
For pumping and large scale applications, contact Custom's Technical
Services Department for more information.

Published Date: 11/14/2014

 Surface Prep / TDS-108

LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment
9 Technical Services Information
For technical assistance, contact Custom technical services at 800-272-
8786 or visit custombuildingproducts.com.

10 Filing System
Additional product information is available from the manufacturer upon
request.

Expected Wear
Properly installed tile will last for more than 60 years.

Related Products
LevelQuik® Latex Primer

Published Date: 11/14/2014

 Surface Prep / TDS-108

LevelQuik® RS (Rapid Setting) Self­Leveling Underlayment
Coverage
SQUARE FOOT COVERAGE PER 50 LB BAG (SQUARE METER PER 22.68 KG)

THICKNESS COVERAGE
1/8" (3.18 mm) 50 ft² (4.6 M²)
1/4" (6.35 mm) 25 ft² (2.3 M²)
1/2" (12.7 mm) 12.5 ft² (1.15 M²)
1" (25.4 mm) 6.25 ft² (0.56 M²)
1.5" (38.1 mm) 4.17 ft² (0.38 M²)

Published Date: 11/14/2014