NIT Calicut

Curriculum of B.Tech. Degree in Mechanical Engineering

Semester 1

No Course Code Course Title Contact hours / week Credits

L T P Total
1 MA1001 Mathematics I 3 1 0 4 3
2 PH1001/CY1001 Physics / Chemistry 3 0 0 3 3
3 MS1001/ ZZ1003 Professional Communication / 3 0 0 3 3
Basic Electrical Sciences
4 ZZ1001/ZZ1002 Engineering Mechanics / 3 0 0 3/4 3
Engineering Graphics 1 0 3
5 ZZ1004/ME1001 Computer Programming/ 2 0 0 2 2
Introduction to Mechanical
Engineering
6 ZZ1091/ZZ1092 Workshop I / Workshop II 0 0 3 3 2
7 PH1091/PY1094 Physics Lab./ Chemistry Lab. 0 0 2 2 1
8 ZZ1094/ ZZ1093/ OT(Value Education(1), Physical - - - - 3*
ZZ1095 Education(1), NSS(1)
Total 14/ 1 5/8 20/21 17+3*
12
*Three courses of one credit each are to be credited within the first four semesters.

Semester 2

No Code Title Contact hours / week Credits

L T P Total
1 MA1002 Mathematics II 3 1 0 4 3
2 CY1001/PH1001 Chemistry / Physics 3 0 0 3 3
3 ZZ1003/MS1001 Basic Electrical Sciences/ 3 0 0 3 3
Professional Communication
4 ZZ1002/ZZ1001 Engineering Graphics/ 1 0 3 4/3 3
Engineering Mechanics 3 0 0
5 ME1001/ ZZ1004 Introduction to Mechanical 2 0 0 2 2
Engineering/ Computer
Programming
6 CY1094/PH1091 Chemistry Lab./ Physics Lab 0 0 2 2 1
7 ZZ1092/ZZ1091 Workshop II / Workshop I 0 0 3 3 2
Total 12/ 1 8/5 21/20 17
14
 Semester 3

No Code Course Title Contact hours / week Credits

L T P Total
1 MA2001 Mathematics III 3 1 0 4 3
2 EE2009 Electrical Measurements and 3 0 0 3 3
Machines
3 ME2001 Mechanics of Fluids 3 0 0 3 3
4 ME2002 Elements of Solid Mechanics 3 0 0 3 3
5 ME2003 Engineering Mechanics – Dynamics 3 0 0 3 3
6 ME2101 Materials Science and Metallurgy 3 0 0 3 3
7 ME2091 Machine Drawing 0 0 3 3 2
8 EE2094 Electrical Measurements and 0 0 3 3 2
Machines Laboratory
Total 18 1 6 25 22

Semester 4

No Corse Code Course Title Contact hours / week Credits

L T P Total
1 MA2002 Mathematics IV 3 1 0 4 3
2 ME2011 Fluid Machinery 3 0 0 3 3
3 ME2012 Applied Mechanics of Solids 3 0 0 3 3
4 ME2013 Mechanics of Machinery 3 0 0 3 3
5 ME2014 Thermodynamics 3 0 0 3 3
6 ME2111 Essentials of Management 3 0 0 3 3
7 ME2092 Fluid Mechanics & Fluid Machinery 0 0 3 3 2
Laboratory
8 CE2095 Strength of Materials Laboratory 0 0 3 3 2
Total 18 1 6 25 22

Semester 5

No Course Course Title Contact hours / week Credits

Code L T P Total
1 ME3001 Dynamics of Machinery 3 0 0 3 3
2 ME3002 Principles of Heat Transfer 3 0 0 3 3
3 ME3101 Management of Production Systems 3 0 0 3 3
4 ME3102 Manufacturing Science 3 0 0 3 3
5 Elective I 3 0 0 3 3
6 ME3003 Environmental Studies for 3 0 0 3 3*
Mechanical Engineers
7 ME3091 Heat Transfer Laboratory 0 0 3 3 2
8 ME3191 Production Engineering Laboratory I 0 0 3 3 2
Total 18 0 6 24 19+3*
 Semester 6

No Course Course Title Contact hours / week Credits

Code L T P Total
1 ME3111 Machining Science and Machine 4 0 0 4 4
Tools
2 ME3112 Metrology and Instrumentation 3 0 0 3 3
3 ME3011 Gas Dynamics 3 0 0 3 3
4 ME3012 Thermal Engineering I 3 0 0 3 3
5 Elective II 3 0 0 3 3
6 ME3192 Metrology and Instrumentation 0 0 3 3 2
Laboratory
7 ME3193 Production Engineering Laboratory II 0 0 3 3 2
Total 16 0 6 22 20

Semester 7

No Course Course Title Contact hours / week Credits

Code L T P Total
1 ME4001 Machine Design I 3 0 0 3 3
2 ME4002 Thermal Engineering II 3 0 0 3 3
3 ME4101 Operations Research 3 0 0 3 3
4 Elective III 3 0 0 3 3
5 ME4091 Heat Engines Laboratory 0 0 3 3 2
6 ME4191 CAD/CAM Laboratory 0 0 3 3 2
7 ME4098 Project 0 0 3 3 3
Total 12 0 9 21 19

Semester 8

No Course Course Title Contact hours / week Credits

Code L T P Total
1 ME4011 Machine Design II 3 0 0 3 3
2 MS4004 Industrial Economics 3 0 0 3 3
3 Elective IV 3 0 0 3 3
4 Elective V 3 0 0 3 3
5 ME4097 Seminar 0 0 3 3 1
6 ME4099 Project 0 0 5 5 5
Total 12 0 8 20 18
 List of Electives

No. Code Subject

1 ME3021 Introduction to Finite Element Methods
2 ME3022 Experimental Stress Analysis
3 ME3023 Theory of Plasticity
4 ME3024 Control Systems Engineering
5 ME3025 Nonlinear Dynamics and Chaos
6 ME3026 Engineering Fracture Mechanics
7 ME3027 Fluid Power Controls
8 ME3028 Advanced Thermodynamics
9 ME3029 Computational Methods in Engineering
10 ME3121 Powder Metallurgy
11 ME3122 Introduction to Marketing
12 ME3123 Design and Analysis of Management Information Systems
13 ME3124 Work Design and Measurement
14 ME3125 Cost Analysis and Control
15 ME3126 Supply Chain Management
16 ME3127 Management of Organisational Behaviour
17 ME3128 Production Planning and Control
18 ME3129 Management of Human Resources
19 ME3130 Quality Planning and Analysis
20 ME4021 Industrial Tribology
21 ME4022 Vehicle Dynamics
22 ME4023 Introduction to Robotics
23 ME4024 Design for Manufacturability
24 ME4025 Mechatronics
25 ME4026 Unconventional Energy Systems
26 ME4027 Computational Fluid Dynamics
27 ME4028 Aerodynamics
28 ME4029 Heating, Ventilation and Air Conditioning
29 ME4030 Fundamentals of Combustion
30 ME4031 Refrigerating and Air Conditioning Systems
31 ME4032 Automobile Engineering
32 ME4033 Introduction to Computer Graphics
33 ME4034 Experimental Methods in Fluid Flow and Heat Transfer
34 ME4122 Mechanical Behaviour and Testing of Materials
35 ME4123 Technology Management
36 ME4125 Competitive Manufacturing Management
37 ME4126 Engineering Optimization
38 ME4127 Accounting and Finance for Engineers
39 ME4128 Simulation Modelling and Analysis
40 ME4129 Modelling of Manufacturing Systems
41 ME4130 Human Factors in Engineering and Design
42 ME3114 CAD/CAM/CIM
 SYLLABI OF
B.TECH DEGREE PROGRAMME IN
MECHANICAL ENGINEERING

(Applicable from 2010 Admission onwards)

DEPARTMENT OF MECHANICAL ENGINEERING

NATIONAL INSTITUTE OF TECHNOLOGY CALICUT

 Detailed syllabi of B.Tech. Degree in Mechanical Engineering

SEMESTERS 1 & 2

MA1001 - MATHEMATICS – I
Prerequisite: Nil
L T P C
3 1 0 3

Module I: Preliminary Calculus & Infinite Series (9L + 3T)

Preliminary Calculus : Partial differentiation, Total differential and total derivative,
Exact differentials, Chain rule, Change of variables, Minima and Maxima of functions
of two or more variables.
Infinite Series : Notion of convergence and divergence of infinite series, Ratio test,
Comparison test, Raabe’s test, Root test, Series of positive and negative terms, Idea of
absolute convergence, Taylor’s and Maclaurin’s series.

Module II: Differential Equations (13L + 4T)

First order ordinary differential equations: Methods of solution, Existence and
uniqueness of solution, Orthogonal Trajectories, Applications of first order differential
equations.
Linear second order equations: Homogeneous linear equations with constant
coefficients, fundamental system of solutions, Existence and uniqueness conditions,
Wronskian, Non homogeneous equations, Methods of Solutions, Applications.

Module III: Fourier Analysis (10 L+ 3T)

Periodic functions: Fourier series, Functions of arbitrary period, Even and odd
functions, Half Range Expansions, Harmonic analysis, Complex Fourier Series,
Fourier Integrals, Fourier Cosine and Sine Transforms, Fourier Transforms.

Module IV: Laplace Transforms (11L + 3T)

Gamma functions and Beta functions, Definition and Properties. Laplace Transforms,
Inverse Laplace Transforms, shifting Theorem, Transforms of derivatives and
integrals, Solution of differential Equations, Differentiation and Integration of
Transforms, Convolution, Unit step function, Second shifting Theorem, Laplace
Transform of Periodic functions.

Text Book:

1. Kreyszig E, ‘Advanced Engineering Mathematics’ 8th Edition, John Wiley &Sons

New York, (1999)
References:
1. Piskunov, ‘Differential and Integral Calculus, MIR Publishers, Moscow
(1974).

2. Wylie C. R. &Barret L. C ‘Advanced Engineering Mathematics’ 6 th

Edition, McGraw Hill, New York, (1995).

3. Thomas G. B. ‘Calculus and Analytic Geometry’ Addison Wesley,

London (1998).

Course Outcomes

CO1:Learn to find the solution of constant coefficient differential equations.

CO2:Acquire knowledge about the notion of convergence of numerical sequences and series
and learn ways of testing convergence.
CO3:Learn the basic definition and properties of partial differentiation of functions of
several variables and to learn to use this to solve problems related to maxima and minima.
CO4:Learn the basic results about the properties of Fourier transform and Fourier series and
its convergence.
CO5: Learn the properties of Laplace transforms and to learn to use this to solve differential
equations.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 PH1001 PHYSICS
Prerequisite: Nil
L T P C

3 0 0 3

Module 1 – Theory of Relativity (6 hours)

Frames of reference, Galilean Relativity, Michelson-Morley experiment, postulates of
Special Theory of Relativity, Lorentz transformations, simultaneity, length
contraction, time dilation, velocity addition, Doppler effect for light, relativistic mass
and dynamics, mass energy relations, massless particles, Description of General
Theory of Relativity.

Module 2 - Quantum Mechanics (10 hours)

Dual nature of matter, properties of matter waves, wave packets, uncertainty principle,
formulation of Schrödinger equation, physical meaning of wave function, expectation
values, time-independent Schrödinger equation, quantization of energy – bound states,
application of time-independent Schrödinger equation to free particle, infinite well,
finite well, barrier potential, tunneling, Simple Harmonic Oscillator, two-dimensional
square box, the scanning tunneling microscope.

Module 3 – Statistical Physics (12 hours)

Temperature, microstates of a system, equal probability hypothesis, Boltzman factor
and distribution, ideal gas, equipartition of energy, Maxwell speed distribution,
average speed, RMS speed, applications – Lasers and Masers, Quantum distributions –
many particle systems, wave functions, indistinguishable particles, Bosons and
Fermions, Bose-Einstein and Fermi-Dirac distribution, Bose-Einstein condensation,
Specific heat of a solid, free electron gas and other applications.

Module 4 – Applications to Solids (14 hours)

Band theory of solids, conductors, semi-conductors and insulators, metals – Drude
model and conductivity, electron wave functions in crystal lattices, E-k diagrams,
band gaps, effective mass, semiconductors, Fermi energy, doping of semiconductor,
conductivity and mobility of electrons, Hall effect, Fundamentals of mesoscopic
physics and nano technology: size effects, interference effect, quantum confinement
and Coulomb blockade. Quantum wells, wires, dots, nanotubes, semiconductor nano
materials, Magnetism: dipole moments, paramagnetism, Curie’s law, magnetization
and hysterisis, Ferromagnetism and Anti-Ferromagnetism.

Text Books

1 Modern Physics for Scientists and Engineers, J. R. Taylor, C.D. Zafiratos and M. A.
Dubson, 2nd Ed., Pearson (2007)
2 Concepts of Modern Physics Arthur Beiser, 6th Ed., Tata McGraw –Hill Publication
(2009)
References

1 Quantum Physics of atoms, Molecules, Solids, Nuclei and Particle, Robert Eisberg
and Robert Resnick, 2nd Ed., John Wiley(2006)
2 Solid state Devices, B. G. Streetman, 5th Ed., Pearson (2006)

Course Outcomes

CO1:Acquire knowledge and understanding of fundamental principles of modern physics.

CO2:Acquire knowledge of basic principles of Quantum Physics and Relativity.
CO3:Acquire knowledge of the basic physics of a collection of particles and the emergent
macroscopic properties.
CO4:Apply principles of quantum and statistical physics to understand properties of
semiconducting and magnetic materials.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 CY1001: CHEMISTRY
Prerequisite: Nil
L T P C

3 0 0 3

Module 1: Chemical Bonding (8 hours)

Quantum mechanical methods in chemical bonding: molecular orbital theory,

symmetry of molecular orbitals, MOs for homonuclear diatomic molecules,
application of MO theory to heteronucleardiatomics, valence bond theory,
hybridization, hybridization involving d orbitals, conjugated molecules, Huckel
molecular orbital theory of conjugated systems, metallic bonding, band theory .

Module2: Spectroscopy (14 hours)

General features of spectroscopy, interaction of radiation with matter, theory and

application of rotational, vibrational, Raman, electronic, mass, NMR, fluorescence and
photoelectron spectroscopy.

Module 3: Transition Metal Chemistry (12 hours)

Bonding in transition metal complexes: coordination compounds, crystal field theory,

octahedral, tetrahedral and square planar complexes, crystal field stabilization
energies, Jahn-Teller theorem, spectral and magnetic properties.

Bio-Inorganic chemistry: Trace elements in biology, heme and non-heme oxygen

carriers, haemoglobin and myoglobin-cooperativity; Bohr effect, Hill coefficient, oxy
and deoxyhaemoglobin, reversible binding of oxygen.

Module 4: Aromaticity (8 hours)

Electron delocalization, resonance and aromaticity; molecular orbital description of

aromaticity and anti-aromaticity, annulenes; ring current, NMR as a tool, diamagnetic
anisotropy; aromatic electrophilic substitutions, aromatic nucleophilic substitutions,
benzyne; reaction mechanisms, reactivity and orientation.

Text Books:

1. J. E. Huheey, E.A. Keiter and R.L. Keiter, Inorganic Chemistry, Principles of

Structure and Reactivity, Harper Collins, New York 1997.

2. F. A. Cotton and G Wilkinson,Advanced Inorganic Chemistry, 5th Edition,

Wiley Interscience, New York, 1988.

3. J. D. Lee, Concise Inorganic Chemistry, Chapman & Hall, London, 1996.

 4. W. L. Jolly, Modern Inorganic Chemistry, McGraw-Hill International, 2nd
Edition, New York, 1991.

5. R. T. Morrison and R N Boyd, Organic Chemistry, 6th Edition, Prentice Hall,

New Delhi, 1999.

6. P. Bruice, Organic Chemistry, 3rd Edition,Prentice Hall, New Delhi ,2001.

7. F. Carey, Organic Chemistry, 5th Edition,McGraw Hill Publishers, Boston,

2003.

8. J. Mc Murray, Organic Chemistry, 5th Edition, Brooks/ Cole Publishing Co,

Monterey, 2000.

9. C.N. Banwell and E. M. McCash, Fundamentals of Molecular

Spectroscopy,McGrawHill, International, UK, 1995.

10. William Kemp, Organic Spectroscopy, 3rd edition, Palgrave, New York, 2005.
11. R.M. Silverstein, F.X. Webster and D.J. Kiemle,Spectrometric Identification of
Organic Compounds, 7thedition,John-Wiley and Sons, New York, 2005.

12. D. L. Pavia, GM. Lampman, GS. Kriz and J.R Vyvyan, I,

Spectroscopy,Cengage Learning India Pvt. Ltd, New Delhi, 2007.

13. B. R.Puri, L. R. Sharma and M. S. Pathania, Principles of Physical Chemistry,

Vishal Publishing CO. Delhi, 2008.

14. P.W. Atkins, Physical Chemistry, 6th Edition, Oxford University Press, Oxford,
1998.

Course Outcomes

CO1: To acquire knowledge on the role of chemistry in solving the problems related to
chemical engineering.
CO2: To acquire knowledge about the fundamental principles of bonding in materials.
CO3: To acquire knowledge on the characterization of materials by modern tools.
CO4: To acquire knowledge on the chemistry of bio-molecules.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 MS1001 PROFESSIONAL COMMUNICATION

Prerequisite: Nil
L T P C

3 0 0 3

Module 1 (11 hours)

Verbal Communication: received pronunciation; how to activate passive vocabulary;

technical/non-technical and business presentations; questioning and answer skills; soft
skills for professionals; role of body postures, movements, gestures, facial expressions,
dress in effective communication; Information/ Desk/ Front Office/ Telephone
conversation; how to face an interview/press conference; Group discussions, debates,
elocution.

Module 2 (9 hours)

Reading Comprehension: skimming and scanning; factual and inferential

comprehension; prediction; guessing meaning of words from context; word reference;
use and interpretation of visuals and graphics in technical writing.

Module 3 (11 hours)

Written Communication: note making and note taking; summarizing; invitation,

advertisement, agenda, notice and memos; official and commercial letters; job
application; resume and curriculum vitae; utility, technical, project and enquiry
reports; paragraph writing: General – Specific, Problem – Solution, Process –
Description, Data – Comment.

Module 4 (11 hours)

Short essays: description and argument; comparison and contrast; illustration; using
graphics in writing: tables and charts, diagrams and flow charts, maps and plans,
graphs; how to write research paper; skills of editing and revising; skills of
referencing; what is a bibliography and how to prepare it.

Text Books

1. Adrian Doff and Christopher Jones: Language in Use – Upper intermediate,

selfstudy workbook and classroom book. (Cambridge University Press)[2000]

2. Sarah Freeman: Written Communication (Orient Longman)[1978]

3. Mark Ibbotson: Cambridge English for Engineering (Cambridge University Press)

November 2008

4. T Balasubramanian: English Phonetics for Indian Students: A Workbook

 (Macmillan publishers India) 2000

Reference

1 Chris Mounsey: Essays and Dissertation (Oxford University Press) February 2005.
2 Sidney Greenbaum: The Oxford English Grammar (Oxford University Press) March
2005
3 Krishna Mohan and MeeraBanerji: Developing Communication Skills (Mac
Millanindia Ltd)[2000]
4 Krishna Mohan and Meenakshi Raman: Effective English Communication (Tata
McGraw Hill)[2000]

Course Outcomes

CO1: Effectively communicate technical material in print.

CO2: Present technical material orally with confidence and poise, including audiovisual
materials.
CO3: Communicate effectively in ways appropriate to the discipline, audience and purpose.
CO4: Think critically and creatively to generate innovative and optimum solutions.
CO5: Identify, evaluate and synthesize information from a range of sources to optimize
process engineering design and development.
CO6: Engage in continuous education, training and research, and take control of their own
learning and development.
CO7: Work effectively and efficiently individually and in teams.
CO8: Be ‘career ready’ for the engineering profession, demonstrate leadership qualities, and
work ethically and professionally.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ZZ1001 ENGINEERING MECHANICS
Prerequisite: Nil
L T P C

3 0 0 3
Part A--Statics
Module 1 (12 hours)
Fundamentals of mechanics: idealisations of mechanics, vector and scalar quantities,
equality and equivalence of vectors, laws of mechanics.
Important vector quantities: Position vector, moment of a force about a point, moment
of a force about an axis, the couple and couple moment, couple moment as a free
vector, moment of a couple about a line.
Equivalent force systems: Translation of a force to a parallel position, resultant of a
force system, simplest resultant of special force systems, distributed force systems.
Equations of equilibrium: Free body diagram, free bodies involving interior sections,
general equations of equilibrium, problems of equilibrium, static indeterminacy.

Module 2 (10 hours)

Applications of Equations Equilibrium: Trusses: solution of simple trusses, method of
joints, method of sections; Friction forces: laws of Coulomb friction, simple contact
friction problems.

Properties of surfaces: First moment, centroid, second moments and the product of a
plane area, transfer theorems, rotation of axes, polar moment of area, principal axes,
concept of second order tensor transformation.

Part B—Dynamics
Module 3 (10 hours)
Kinematics of a particle: Introduction, general notions, differentiation of a vector with
respect to time, velocity and acceleration calculations, rectangular components,
velocity and acceleration in terms of cylindrical coordinates, simple kinematical
relations and applications.
Particle dynamics: Introduction, rectangular coordinates, rectilinear translation,
Newton’s law for rectangular coordinates, rectilinear translation, cylindrical
coordinates, Newton’s law for cylindrical coordinates.

Module 4 (10 hours)

Energy and momentum methods for a particle: Analysis for a single particle,
conservative force field, conservation of mechanical energy, alternative form of work-
energy equation, Linear momentum, impulse and momentum relations, moment of
momentum.
Vibrations: Single degree of freedom systems, free vibration, undamped and damped,
forced vibration, sinusoidal loading, introduction to multi degree of freedom systems,
illustration using two degree-of-freedom systems.

Text Book
1 H. Shames, Engineering Mechanics—Statics and Dynamics, 4th Edition, Prentice Hall
of India, 1996.

Reference Books
1. F.P. Beer and E.R. Johnston, Vector Mechanics for Engineers – Statics, McGraw Hill
Book Company, 2000.
2. J.L. Meriam and L.G. Kraige, Engineering Mechanics – Statics, John Wiley & Sons, 2002.

Course Outcomes

CO1: Draw proper free body diagrams based on the applied loads and boundary conditions.
CO2: Learn to identify the problem type to be static or dynamic based on the defining
features.
CO3: Find solutions to rigid body statics problems using equations of equilibrium.
CO4: Find solutions to particle dynamics problems using Newton's law, energy methods and
momentum methods.

Evaluation Weightage (%)

Component
Test 1 15
Test 2 20
Assignments 15
End Semester 50
Examination
 ZZ1002 ENGINEERING GRAPHICS

Prerequisite: Nil
L T D C

2 0 3 3

Module 1 (4Lecture+6drawing hours)

Introduction to Engineering Graphics – Drawing instruments and their use – Different
types of lines - Lettering & dimensioning – Familiarization with current Indian
Standard Code of Practice for Engineering Drawing.
Scales, Plain scales, Diagonal scales, Vernier scales.
Introduction to orthographic projections- Horizontal, vertical and profile planes – First
angle and third angle projections – Projection of points in different coordinates –
Projections of lines inclined to one of the reference planes

Module II
Projections of lines inclined to both the planes – True lengths of the lines and their
angles of inclination with the reference planes – Traces of lines.
(4Lecture+6 drawing hours)

Projection of plane lamina of geometric shapes inclined to one of the reference planes
– inclined to both the planes, Traces of planes (2Lecture+3 drawing hours)

Projections on auxiliary planes (2lecture +3 drawing hours)

Module III (4Lecture+6 drawing hours)

Projections of polyhedra and solids of revolution, projection of solids with axis

parallel to one of the planes and parallel or perpendicular to the other plane –
Projections with the axis inclined to one of the planes. Projections of solids with axis
inclined to both the planes – Projections of spheres and combination of solids.

Module IV
Sections of solids by planes perpendicular to at least one of the reference planes – True
shapes of sections. (2 lectures, 3 drawing hours)

Developments, development of the lateral surface of regular solids like, prisms,

pyramids, cylinders, cones and spheres, development of truncated solids
(2 lectures +3 drawing hours)
Isometric projection – Isometric scale – Isometric views – Isometric projection of
prisms, pyramids, cylinders, cones, spheres and solids made by combination of the
above. (2 lectures +6 drawing hours)
Text book
1. Bhatt N. D, Elementary Engineering Drawing, Charotar Publishing House, Anand,
2002

References
1. Narayana K L and Kannaiah P, Engineering Graphics, Tata McGraw Hill, New
Delhi, 1992
2. Luzadder W J, Fundamentals of Engineering Drawing, Prentice Hall of India,
New Delhi, 2001

3. Thomas E French and Charkes J V, Engineering Drawing & Graphing

Technology, McGraw Hill Book Co, New York, 1993

4. Venugopal K, Engineering Drawing and Graphics, New Age International Pvt.

Ltd., NewDelhi,1994

Course Outcomes

CO1: Ability of writing, sketching, scale drawing and visualization skills

CO2: Gets training in the transformation of the imagined data to present as drawings so that
the communication skill will be increased especially in technical subjects.
CO3: Imparts the training in multi-view representations and its conversion into pictorial
views and the reverse also.
CO4: Ability to understand the different standards in technical drawing and to help in
reaching future engineering positions especially in research and design.

Evaluation Weightage (%)

Component
Test 1 20
Assignments 30
End Semester 50
Examination
 ZZ1003 BASIC ELECTRICAL SCIENCES
Pre-requisite: NIL L T P C
3 0 0 3

Module – 1 (11 Hours)

Two Terminal Element Relationships

Inductance - Faraday’s Law of Electromagnetic Induction-Lenz’s Law -Self and Mutual
Inductance-Inductances in Series and Parallel-Mutual Flux and Leakage Flux-Coefficient of
Coupling-Dot Convention-Cumulative and Differential Connection of Coupled Coils-
Capacitance - Electrostatics-Capacitance-Parallel Plate Capacitor-Capacitors in series and
parallel- Energy Stored in Electrostatic Fields- V-I relationship for Inductance and
Capacitance - V-I relationship for Independent Voltage and Current Sources
Magnetic Circuits
MMF, Magnetic Flux, Reluctance- Energy Stored in a Magnetic Field-Solution of Magnetic
Circuits.
Analysis of Resistive Circuits
Solution of resistive circuits with independent sources- Node Analysis and Mesh Analysis-
Nodal Conductance Matrix and Mesh Resistance Matrix and symmetry properties of these
matrices-Source Transformation- Circuit Theorems - Superposition Theorem-Thevenin’s
Theorem and Norton’s Theorem- Maximum Power Transfer Theorem

Module – 2 (10 Hours)

Single Phase AC Circuits

Alternating Quantities- Average Value - Effective Value - Form and Peak factors for square,
triangle, trapezoidal and sinusoidal waveforms - Phasor representation of sinusoidal
quantities - phase difference -Addition and subtraction of sinusoids - Symbolic
Representation: Cartesian, Polar and Exponential forms
Analysis of a.c circuits R, RL, RC, RLC circuits using phasor concept - Concept of
impedance, admittance, conductance and susceptance –Power in single phase circuits –
instantaneous power – average power – active power – reactive power – apparent power –
power factor – complex power – Solution of series, parallel and series-parallel a.c circuits

Module - 3 (14 hrs)

Introductory Analog Electronics-Semiconductor Diode: Principle, Characteristics -

Applications: Rectifier Circuits -Zener Diode, LED, Photo diode, IR diode-Bipolar Junction
Transistor: Principle, Operation, Characteristics (CB, CE, CC)-
Principle of working of CE, CB and CC amplifiers, quantitative relations for midband
operation, input and output resistance levels – qualitative coverage on bandwidth - cascading
considerations.
Introductory Digital Electronics: Transistor as a switch – switching delays, inverter operation
Digital Electronics: Number Systems and Conversions- Logic Gates and Truth Tables –
Boolean Algebra – Basic canonical realizations of combinatorial circuits.
Standard Combinatorial Circuit SSI and MSI packages (Adder, Code Converters, 7-Segment
Drivers, Comparators, Priority Encoders etc). MUX-based and ROM-based implementation
of combinatorial circuits.

Module - 4 (7 hours)

Measuring instruments
Basics of electronic/digital voltmeter, ammeter, multimeter, wattmeter and energy meter.
Measurement of Voltage, Current and Resistance. Introduction to Cathode Ray Oscilloscope
- CRT, Block diagram of CRO.

Text Books:

1. Electric Circuits, James W Nilsson and Susan A Riedel, Pearson, 8 th Edn, 2002

2. Electronic Devices and Circuit Theory, Robert L Boylestead & L Nashelsky,

Pearson, 9th Edition, 2007

3. Digital Design , Morris Mano , PHI, 3rd Edition, 2005

Course Outcomes:

CO1: Analysis of Resistive Circuits and Solution of resistive circuits with independent
sources.
CO2: Two Terminal Element Relationships for inductors and capacitors and analysis of
magnetic circuits.
CO3: Analysis of Single Phase AC Circuits, the representation of alternating quantities and
determining the power in these circuits.
CO4: To acquire the knowledge about the characteristics and working principles of
semiconductor diodes, Bipolar Junction Transistor.
CO5: To get an insight about the basic introduction of Digital electronics.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ZZ1004 COMPUTER PROGRAMMING
Pre-requisite: NIL
L T P C

2 0 0 2
Module 1 (7 Hours)
Data Types, Operators and Expressions: Variables and constants - declarations -
arithmetic, relational and logical operators – Assignment operator and expressions –
conditional expressions – precedence and order of evaluation.
Control Flow: Statements and blocks – if-else, switch, while, for and do-while
statements – break and continue statements, goto and labels.

Module 2 (7 Hours)
Functions and Program structure: Basics of functions, Parameter passing – scope rules
- recursion.

Module 3 (7 Hours)

Pointers and Arrays: Single and multidimensional arrays - Pointers and arrays –
address arithmetic - Passing pointers to functions.

Module 4 (7 Hours)

Structures and Unions: Basics of structures, Structures and functions – Arrays of

Structures – Pointers to structures – self referential structures – Type definitions –
Unions.
Input and Output: Standard input and output – Formatted output – variable length
argument list – file access.

Text Book:

1. B. W. Kernighan and D. M. Ritchie, The C Programming Language (2/e), Prentice

Hall, 1988.

References:

1. B.S. GottFried, Schaum's Outline of Programming with C(2/e), McGraw-Hill,

1996.
2. C. L. Tondo and S. E. Gimpel, The C Answer Book(2/e), Prentice Hall, 1988.
3. B. W. Kernighan, The Practice of Programming, Addison-Wesley, 1999.
Course Outcomes

CO1: To introduce the role of computer programming in engineering.

CO2: Familiarization of programming languages used for computer programming.
CO3: To train the student for development of their programming skills.
CO4: To highlight the role of programming in engineering with suitable examples.

Evaluation Weightage (%)

Component
Test 1 15
Test 2 15
Assignments 20
End Semester 50
Examination
 ME1001 - Introduction to Mechanical Engineering

Pre-requisite: NIL
L T P C

2 0 0 2

1) General Introduction (Engineering, ingeniere-ingenious, Mechanical Engg profession,

Historical aspects, Overview of curriculum)
2) a) Creativity and Problem Solving skills (Levels of thinking, intelligence & creativity,
invention & innovation, Basic steps in problem formulation & solving, Units and
significant digits). b) Communication Skills (Oral, written and graphical
communication, Presentation skills)
3) Materials and Stresses (Fundamental properties, classifications, applications, simple
problems).
4) Motion and Power transmission (Kinematics and dynamics of machinery, power
transmission elements, concepts from friction and wear)
5) Fluids Engineering (fluid mechanics – basics & historical aspects, hydraulic machines,
advanced topics like gas dynamics)
6) Thermodynamics and Heat Transfer (Basic principles, significance of thermodynamics
in Mechanical Engg., relationship with mechanics subjects, modes of heat transfer)
7) Thermal Engineering and Energy Systems (Historical aspects, Internal and external
combustion engines, gas turbines, heating, ventilation and air-conditioning, power
plants, energy conservation)
8) Manufacturing Processes (Basic processes like machining, casting, forging etc.)
9) Manufacturing Systems (Machine tools, Production systems, advanced systems like
CNC, robots, assembly lines etc.)
10) Mechanical Design (Basic steps in design, material selection, design for
manufacturability etc.)
11) Industrial Engineering and Principles of Management (Work study, optimization,
software tools, interesting problems transportation planning, job sequencing etc., basic
concepts of management)
12) About automobile engineering; Nanotechnology, and allied topics.

References
1) An Introduction to Mechanical Engineering, J. Wickert, Cengage Learning, 2 ndEdn.,
2006
2) Engineering Basics, Saeed Moaveni, Cengage Learning, 2009.
 3) Other reference materials and course materials as suggested by faculty.

Course Outcomes

CO1: To give an overview, introduce and motivate the students towards Mechanical
Engineering.
CO2: To give a clear inter-relationship with various subjects in Mechanical Engineering ,
and even with subjects of other branches of engineering.
CO3: To impart an ability to solve a variety of elementary problems which gives a
smooth passage into the field of Mechanical Engineering.
CO4: To understand and appreciate the significance of various allied aspects that are
required in the field of Mechanical Engineering such as communication, drawing,
mathematics and basic sciences.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ZZU1091 WORKSHOP PRACTICE I
Pre-requisite: NIL
L T P C

0 0 3 2

CIVIL ENGINEERING WORKSHOP

Introduction to Construction Materials: Cement, sand, coarse aggregate, structural steel,

brick, timber, concrete – methods of testing (3 hours)
Masonry: English bond – Flemish bond –wall –junction – one brick – one and a half brick -
Arch construction. (6 hours)
Plumbing: Study of water supply and sanitary fittings—water supply pipe fitting –tap
connections - sanitary fittings. (3hours)
Surveying: Introduction to land surveying and linear measurements; Introduction to leveling.
(9 hours)
ELECTRICAL WORKSHOP
1
a) Familiarization of wiring tools, lighting and wiring accessories, various types of wiring
systems.
b) Wiring of one lamp controlled by one switch
2
a) Study of Electric shock phenomenon, precautions, preventions; Earthing b) Wiring of
one lamp controlled by two SPDT Switch and one 3 pin plug socket independently.
3
a) Familiarization of types of Fuse, MCB, ELCB etc.
b) Wiring of fluorescent lamp controlled by one switch from panel with ELCB & MCB.
4
a) Study of estimation and costing of wiring
b) Domestic appliance – Wiring, Control and maintenance: Mixer machine, Electric Iron,
fan motor, pump motor, Battery etc.

Reference:

1. K B Raina & S K Bhattacharya: Electrical Design Estimating and costing, New Age
International Publishers, New Delhi,2005.Uppal S. L., Electrical Wiring & Estimating,
Khanna Publishers---5th edition, 2003

2. John H. Watt, Terrell Croft :American Electricians' Handbook: A Reference Book for the
Practical Electrical Man- McGraw-Hill, 2002

Course Outcomes

CO1: Acquire knowledge on the basic civil engineering practices of brick and concrete
masonry, plumbing and surveying.
CO2: Get hands on training in basic masonry and surveying.
CO3: Understand the quality requirements and quality testing procedures of selected
building material, viz., cement, fine aggregate, coarse aggregate, concrete, timber and steel.
CO4: Acquire knowledge about various types of wiring systems, wiring tools, lighting &
wiring accessories, wiring estimation & costing, etc.
CO5: Acquire knowledge about household electrical appliances, need of earthing, electric
shock, etc.
 ZZ1092 WORKSHOP PRACTICE II
Pre-requisite: NIL

L T P C

0 0 3 2

MECHANICAL WORKSHOP
(Eight classes of 3 hour duration each)

The course is intended to expose the student to the manufacturing processes through
hands on training in the sections of Central Workshop. After the course, the student
acquires the skill in using various tools, measuring devices, and learns the properties
of different materials at varying conditions.

1) Carpentry: Study of tools and joints – plaining, chiseling, marking and sawing
practice, one typical joint- Tee halving/Mortise and Tenon/ Dovetail

2) Fitting: Study of tools- chipping, filing, cutting, drilling, tapping, about male and
female joints, stepped joints- one simple exercise of single V joint for welding
exercise.

3) Welding: Study of arc and gas welding, accessories, joint preparation, Exercise of a
single V joint

4) Smithy: Study of tools, forging of square or hexagonal prism/ chisel/bolt

5) Foundry: Study of tools, sand preparation, moulding practice.

6) Sheet Metal work: Study of tools, selection of different gauge sheets, types of
joints, fabrication of a tray or a funnel

7) Plumbing Practice: Study of tools, study of pipe fittings, pipe joints, cutting, and

threading

8) Lathe Exercise: Study of the basic lathe operations, a simple step turning exercise.

References

1) Chapman W.A.J., Workshop Technology. Parts 1 & 2, 4th Edition, Viva

Books P. Ltd., New Delhi, 2002

2) HajraChoudhury.Workshop Technology Vol 1 & 2, Media Promoters &

Publishers P.Ltd, Bombay, 2004

3) Welding Handbook. Miami, American Welding Society, 2000

4) Metals Handbook. Vol 6, Welding, Brazing & Soldering. Metals Park, Ohio,
American Society of Metals, 1998
 5) SeropeKalpakjian. Manufacturing Engineering & Technology. Pearson Steven
R. Schmid Education (Asia) Inc., Delhi, 2002.

6) Anderson J., Shop Theory. Tata McGraw Hill, New Delhi, 2002

7) Olson D.W., Wood and Wood working. Prentice Hall India. 1992

8) Douglass J.H., Wood Working with Machines. McKnight &McKnight Pub.

Co. Illinois, 1995

9) Tuplin W.A., Modern Engineering Workshop Practice Odhams Press, 1996

10) P.L. Jain. Principles of Foundry Technology. 4th Edition, Tata McGraw Hill,
2008.
11) R.K.Singal, MridulSingal, Rishi Sringal.Basic Mechanical Engineering. 2007

Course Outcomes

CO1: Student is exposed to the practical field, which any professional must go through to be
real professional, even though he/she may not be opting for this job after graduation.
CO2: The student is made familiar with the basis manufacturing processes- Casting,
Forming, Joining and Machining.
CO3: The student learns about the properties of different materials- Hardness, ductility,
sharpness, heat resistance, grain orientation, application, and the specific tools used for
converting to useful forms, by observation, demonstrations, and self studies.
CO4: The student also learns about the various measuring devices apart from scales, Vernier
calipers, micrometers etc. which are used in the metrology field.
CO5: The skill of sequencing the operations so as to execute a task with least time and least
rejection too is learnt. This makes him/her confident to command over the subordinates while
employed as a leader.
CO6: The student learns how to substantiate the academic knowledge which he acquires
through class rooms with practicals.
CO7: How to carry out a task as a member in a group team, is professional team, is also
experienced.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination

ELECTRONICS WORKSHOP
1
a) Familiarization of electronic components colour code, multimeters.
b) Bread board assembling - Common emitter amplifier
2
a) Study of soldering components, solders, tools, heat sink.
b) Bread board assembling – phase shift oscillator
3
a) Soldering practice - Common emitter amplifier
b) Soldering practice - Inverting amplifier circuit
4
a) Study of estimation and costing of soldering –PCB: 3 phase connections
b) Domestic appliances – Wiring PCB, control, Identification of fault: Electronic Ballast,
fan egulator, inverter, UPS etc.

Reference:

1. G. Randy Slone - Tab Electronics Guide to Understanding Electricity and Electronics, Mc-
GrawHill, 2000
2. Jerry C Whitaker -The Resource Handbook of Electronics, CRC Press-2001
 PH1091 PHYSICS LAB
Pre-requisites: NIL L T P C

0 0 2 1
LIST OF EXPERIMENTS

1. Magnetic Hysteresis loss - Using CRO

2. Band gap using four probe method

3. Hall effect- determination of carrier density, Hall coefficient and mobility

4. Solar cell characteristics

5. Double refraction – measurement of principle refractive indices.

6. Measurement of N.A & Attenuation

7. Measurement of e/m of electron – Thomson’s experiment

8. Determination of Planck’s constant

9. Measurement of electron charge – Milliken oil drop experiment

10. Determination of Magnetic Field along the axis of the coil

11. Newton’s rings

12. Laurent’s Half shade polarimeter –determination of specific rotatory power

13. Study of P-N junction

14. Study of voltage-current characteristics of a Zener diode.

15. Laser – measurement of angle of divergence & determination of λ using

grating
16. Measurement of Magnetic susceptibility- Quincke’s Method / Gouy’s balance.

17. Mapping of magnetic field

Reference:

1. Experiments in Engineering physics, Avadhanulu, Dani and Pokley, S. Chand &

Company ltd (2002).

2. Experiments in Modern Physics, A.C. Melissinos, J. Napolitano, Academic

Press (2003)

3. Practical physics, S.L. Gupta and V. Kumar, PragathiPrakash (2005)

Course Outcomes

CO1: To develop experimentation skills and understand importance of measurement

practices in Science & Technology.
CO2: Develop analytical skills for interpreting data and drawing inferences.
CO3: Understand nature of experimental errors and practical means to estimate errors in
acquired data.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 CY1094: CHEMISTRY LABORATORY
Pre-requisites: Nil

L T P C

0 0 2 1

Total Hours: 28

Potentiometric and conductometric titrations, complexometric and iodimetric

estimations, polarimetry, determination of pH, single step organic / inorganic
preparations, colorimetry, determination of eutectic point.

References:

1. G.H Jeffery, J Bassett, J Mendham, R.C Denny, Vogel’s Text Book of

Quantitative Chemical Analysis, Longmann Scientific and Technical, John
Wiley, New York.

2. J.B Yadav, Advanced Practical Physical Chemistry, Goel Publishing House,

2001.

3. A.I Vogel, A.R Tatchell, B.S Furnis, A.J Hannaford, P.W.G Smith, Vogel’s
Text Book of Practical Organic Chemistry, Longman and Scientific Technical,
New York, 1989.

Course outcomes:
CO1: To acquire practical knowledge on the basic chemistry principles to apply in
engineering.
CO2: To acquire practical knowledge on the techniques for the preparation and
characterization of materials.
CO3: To acquire knowledge on electrochemical techniques.
CO4: To acquire training in accurate and precise data collection.
 ZZ1093: Physical Education

Module 1
 Introduction, definitions, aims & objectives of Physical Education.
 Importance and scope of Physical Education.
 Health, Physical fitness and wellness.
• Importance and relevance of Physical Education in NITC curriculum.

Module 2

• Components of physical fitness.

• Types of physical fitness.
• Benefits of exercise – physical and physiological.
• Fitness balance.

Module 3
• Physical exercise.
• Principals of Physical exercise.
• Activities for developing physical fitness components – walking, jogging, running,
weight training, stretching, yogasanas.
• Athletic injuries and their management.
• Nutritional balance.
• Postural deformities and their corrections.

Module 4
• Motivation and its importance in sports.
• Psychological factors affecting sports performance – stress, anxiety, tension,
aggression.
• Personality, self confidence and performance.
• Team cohesion and leadership in sports.

Module 5
• Lifestyle diseases and its management
o Diabetes
o Hypertension
o Obesity
o Osteoporosis
o Coronary heart diseases
o Cholesterol
o Backpain
Module 6
• Olympic Values Education.
• Event management.
Course Outcomes

II. IN TERMS OF AWARENESS INCULCATED BY STUDENTS:

a) Every participant is oriented and introduced to campus physical education-sports

activities and infrastructure.
b) Everyone is made aware of the relevance of physical education in the NITC curriculum.
c) Everyone is inculcated with desired health related physical fitness awareness.
d) Every student is inculcated with Olympic Values that go to make a good citizen.
e) Every student is made aware of the scientific bases of physical education.

II. IN TERMS OF PERFORMANCE IN SPORTS ACTIVITIES BY STUDENTS:

a) Each student is made capable of selecting a game/ activity of his/ her choice to pursue on
the campus to enjoy/ entertain and thereby develop good health and fitness which he/she
would carry over to post-campus life for maintaining health, fitness and wellness.
b) Students found to be more proficient in a game is spotted for special care which may lead
him/her to a berth in the institute teams..
c) Higher level of exposure ensured to team members with professional training to master
his/her ability.
d) Intramural and open mass participation activities ensure higher percentage of participation
for students as an outcome and follow-up of i-credit course awareness.
e) The uniqueness of the course is that it identifies and places every student with a role to
play in participation, organization and administration of sporting programmes whether in-
campus or off-campus.
f) The most notable achievement of the course is that it calls for more and more infrastructure
on the campus since the percentage of involvement by student is very high.

Evaluation Weightage (%)

Component
Attendance 40
Involvement
and overall 20
improvement
Group
40
projects
 ZZ1094 Value Education

Human Values-Values in Social interactions-Social norms and sanctions-Need for value

ducation-Technology development and its impact on society-sustainability of modern
technology-Concept of holistic development-Need for inner transformations-living in tune
with nature-Professional ethics-Holistic approach in engineering design-Role and social
responsibility of an engineer.

A mini project in indentified areas/topics in groups of not more than five. The work has to be
completed and a report to be submitted at the end. The work can be done under the guidance
of the faculty advisor / any faculty member in MED, NITC and the attendance and progress
report to be obtained from concerned faculty member.

Students are required to attend and actively participate in all the value education related
lectures arranged at the institute level.

Course Outcomes:

CO1: Build an overall awareness, about one’s surroundings its needs, its dynamics and
sensitivity to its welfare and betterment.
CO2: Bring about a qualitative change in overall health of society.
 ZZ1095 NSS

i. Understand the community in which one works

ii. Understand oneself in relation to his/her community
iii. Identify the needs and problems of the community and involve in problem solving
process
iv. Develop among oneself a sense of social and civic responsibility
v. Utilize ones knowledge in finding practical solution to individual and community
problems
vi. Develop competence required for group living and sharing of responsibilities
vii. Gain skills in mobilizing community participation
viii. Acquire leadership qualities and democratic attitude
ix. Develop capacity to meet emergencies and natural disasters and
x. Practice national integration and social harmony

Course Objectives

CO1: The students will be able to work more cohesively in a group

CO2: The student will have a broader vision on life with social dimensions
CO3: The student will be more empathetic in their attitude towards fellow beings
CO4: The student will be capable of demonstrating service mentality where it is required
CO5: The student will be more patriotic in their approach
 MA1002 - MATHEMATICS II
Pre-requisites: NIL
L T P C
3 1 0 3

Module I (11 L + 3T)

Linear Algebra I: Systems of Linear Equations, Gauss’ elimination, Rank of a
matrix, Linear independence, Solutions of linear systems: existence, uniqueness,
general form. Vector spaces, Subspaces, Basis and Dimension, Inner product spaces,
Gram-Schmidt orthogonalization, Linear Transformations.

Module II (11 L+ 3T)

Linear Algebra II: Eigen values and Eigen vectors of a matrix, Some applications of
Eigen value problems, Cayley-Hamilton Theorem, Quadratic forms, Complex
matrices, Similarity of matrices, Basis of Eigen vectors – Diagonalization.

Module III (10L+3T)

Vector Calculus I: Vector and Scalar functions and fields, Derivatives, Curves,
Tangents, Arc length, Curvature, Gradient of a Scalar Field, Directional derivative,
Divergence of a vector field, Curl of a Vector field.

Module IV (11 L+4T)

Vector Calculus II: Line Integrals, Line Integrals independent of path, Double
integrals, Surface integrals, Triple Integrals, Verification and simple applications
of Green’s Theorem, Gauss’ Divergence Theorem and Stoke’s Theorem.

Text Book:

1. Kreyzig E, Advanced Engineering Mathematics, 8thEdn, John Wiley & Sons, New
York (1999).

Reference:

1. Wylie C. R &Barrret L. C, Advanced Engineering Mathematics, 6 thEdn,

McGraw Hill, New York (1995).

2. Hoffman K &Kunze R, Linear Algebra, Prentice Hall of India, New Delhi

(1971).

Course outcomes:

CO1: Acquire knowledge about the ideas and techniques of linear algebra, and to illustrate
some of their applications in engineering.
CO2: Acquire knowledge about the physical interpretation of the gradient, divergence and
curl.
CO3: Acquire knowledge of vector calculus.
CO4: Prepare to evaluate multiple integrals in rectangular, polar, spherical and cylindrical
coordinates.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 SEMESTER 3
MA2001MATHEMATICS III (PROBABILITY & STATISTICS)

Prerequisite: MA 1001 L T P C
3 1 0 3

Module 1: Probability distributions (15 Hours)

Random variables, Binomial distribution, Hyper- geometric distribution, Mean and variance of a probability
distribution, Chebyshev’s theorem, Poisson distribution, Geometric distribution, Normal Distribution, Uniform
distribution, Gamma distribution, Beta distribution, Weibull distribution. Joint distribution of two random
variables.

Module 2: Sampling distributions and Inference concerning means (14 Hours)

Population and samples, The sampling distribution of the mean ( σ known and σ unknown ), Sampling
distribution of the variance, Maximum Likelihood Estimation, Point estimation and interval estimation, point
estimation and interval estimation of mean and variance, Tests of hypothesis, Hypothesis concerning one mean,
Inference concerning two means.

Module 3: Inference concerning variances proportions (13Hours)

Estimation of variances , Hypothesis concerning one variance, Hypothesis concerning two variances ,
Estimation of proportions , Hypothesis concerning one proportion , Hypothesis concerning several proportions,
Analysis of r x c tables, Chi – square test for goodness of fit.

Module 4: Regression Analysis (14 Hours)

Bi-variate Normal distribution- joint, marginal and conditional distributions. Curve fitting, Method of least
squares, Estimation of simple regression models and hypothesis concerning regression coefficients, Correlation
coefficient- estimation of correlation coefficient, hypothesis concerning correlation coefficient. Estimation of
curvilinear regression models,
Analysis of variance:-General principles, Completely randomized designs, Randomized block diagram, Latin
square designs, Analysis of covariance.

Text Book

Johnson, R. A., Miller and Freund’s Probability and Statistics for Engineers, 6thedition., PHI, 2004.

References

1. Levin R. I. & Rubin D. S., Statistics for Management, 7th edition, PHI, New Delhi, 2000.
2. S.M. Ross, Introduction to Probability and statistics for Engineers, 3 rd edition, Academic
Press(Elsevier), Delhi, 2005.

Course Outcomes

CO1: Acquire knowledge about important probability distributions and their properties.
CO2: Acquire knowledge about statistical parameter estimation.
CO3: Acquire knowledge about statistical hypotheses tests.
CO4: Acquire knowledge about regression and correlation analysis.
CO5: Acquire knowledge about ANOVA principles and methods.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 EE2009 ELECTRICAL MEASUREMENTS AND MACHINES

Prerequisite: Nil

L T P C
3 0 0 3

Module 1 (9 hours)

Electromechanical Energy Conversion principles - Types of machines - Basics of rotating machines - Construction -
Rotating magnetic field - Principles of operation - Emf and torque equation - Losses and efficiency.

Module 2 (12 hours)

DC Machines: principle of operation – generators and motors – classification –characteristics - starter - speed control - load
test - Swinburne’s test - applications.
Transformers: Transformer Construction – principle of operation-equivalent circuit – regulation – efficiency – OC and SC
tests –introduction to three phase transformer.

Module 3 (15 hours)

Alternators: Types, principle of operation - Synchronous motors: Principle of operation- starting- applications-
Introduction to power Generation, Transmission and distribution system.
Induction Motors: Principle of operation – types – tests – Torque slip and performance characteristics – starting – speed
control schemes – applications.
Single phase and special machines: FHP induction motors – universal motors - stepper motors – servo motors - tacho
generators.

Module 4 (6 hours)

Measurement of high and low resistance using Voltmeter/ Ammeter method- Measurement of power in single phase ac
circuits using three voltmeter method, three ammeter method and one wattmeter method - Measurement of power in three
phase circuits using two wattmeter method- Measurement of Energy using single-phase energy meter.

References

1. Hughes, K, Electrical Technology, E.L.B.S., 1996.

2. Nagrath, I.J, Kothari D.P, Electrical Machines, Tata McGraw-Hill Publishing Company Limited-New Delhi,1997.
3. Cotton, H., Advanced Electrical Technology, CBS Publishers and Distributors, New Delhi,1984.
4. Vincent Del Toro, Electrical Machines & Power systems, Prentice Hall, 1998.
5. Chapman, S.J, Electric Machines & Power systems, McGraw Holl,1999.
6. Say, M.G, Alternating Current Machines, Pittman, 1983.
7. Vertnott, C.C., Fractional & sub-fractional Horse-power Electric Motors, McGraw Hill, New York, 1978.
8. Sawhney, A.K, Electrical & Electronic Measurements & Instrumentation, Dhanpat Rai & Sons, 1996.
9. Gupta, B.R & Vandana Singhal, Fundamentals of Electric machines, D. K Publishets, New Delhi, 2000.
10. Soni, Gulpta & Bhatnagar, A course in Electric Power, Dhanpat Rai & Sons.

Course Outcomes

CO1:.Acquire knowledge about the fundamental principles and classification of electromagnetic machines.
CO2: Acquire knowledge about the constructional details and principle of operation of dc machines.
CO3:.Acquire knowledge about the working of dc machines as generators and motors.
CO4: Acquire knowledge about the constructional details, principle of operation, testing and applications of
transformers.
CO5: Acquire knowledge about the constructional details and principle of operation of three phase and single
phase induction motors.
CO6:Acquire knowledge about the starting and speed control of induction motors.
CO7:Acquire knowledge about testing and applications of induction motors.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2001 MECHANICS OF FLUIDS

Pre requisite: ME1001 Introduction to Mechanical Engineering

Total hours: 42 L T P C
3 0 0 3
Module 1 (13 hours)
Preliminaries, Concept of continuum, Properties of fluids – density – pressure – viscosity - surface tension -
capillarity - vapour pressure, Fluid statics, Basic equations of fluid statics, Variation of pressure in a fluid, -
Manometry - Forces on surfaces and bodies in fluids, Floatation - stability of bodies in fluid - metacentric
height and its measurement, Fluids in rigid body motion, Fluid kinematics -Eulerian and Lagrangian description
- local and material rates - deformation of a fluid element -strain rate-velocity relations, Graphical description
of flow – streamlines - path lines - streak lines - stream tube, Fluid dynamics - concept of the control volume -
Reynolds transport equation and its use to formulate fluid mechanics problems, Integral and differential forms
of the continuity - momentum and energy equations, Illustrative examples.
Module 2 (11 hours)
One dimensional flow through pipes, Non viscous equation for the flow through a stream tube and along a
stream line – Euler’s equation – Bernoulli’s equation, - Energy equation, Applications of the one dimensional
equations - velocity and flow measuring devices and quasi steady problems, Laminar and turbulent flow
through pipes - Hagen-Poiseuille equation - Darcy-Weisbach equation - pipe friction -Moody’s chart - minor
losses in pipes

Module 3 (10 hours)

Two dimensional incompressible inviscid flows –Vorticity - Vortex tube - Irrotational flow - Velocity potential,
Stream function - relation between streamfunction and potential function in ideal flows -Equation of a
streamline - governing equations, Fundamental flow patterns, Combination of basic patterns - Rankine half
body - Rankine oval - Doublet and flow over a cylinder, Magnus effect and the calculation of lift on bodies.
Module 4 (8hours)
Plane viscous flow past bodies, The boundary layer - Prandtl’s boundary layer equations, Blasius solution for
the boundary layer over a flat plate, Karman’s Momentum Integral equations - Solutions using simple profiles
for the boundary layer on flat plate - calculation of skin friction drag.
Reference Books
1. Shames,I.H., ‘Mechanics of fluids’, Mc Graw Hill Book Co., 1986.
2. White,F.M., ‘Fluid Mechanics’, 6th Ed., Tata Mc Graw Hill, New Delhi, 2009.
3. Cengel, Y.A, Cimbala, John, M., ‘Fluid Mechanics, Fundamentals and Applications’, 7th Ed. Tata Mc
Graw Hill, New Delhi, 2009.
4. Gupta,V., Gupta,S.K.., ‘Fluid Mechanics and its applications’, New Age International, New Delhi, 2005.
5. Som, S.K., and Biswas, G., ‘Fluid Mechanics and fluid Machines’, 2nd Ed., Tata Mc Graw Hill, New
Delhi,2005.

Course Outcomes

CO1: To familiarize the concepts of continuum, properties of fluid, pressure variation and measurement,
pressure on submerged and flowing bodies, RTT and its applications.
CO2: To study 1-D viscous and non-viscous flow through pipes. Bernoulli's equation, laminar
and turbulent flow, Moody's chart.
CO3: To study 2-D flows, irrotational flow, stream function and velocity potential, governing equation, flow
pattern.
CO4: To study about viscous and non-viscous flow over bodies, boundary layer calculation of lift and drag
forces.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2002 ELEMENTS OF SOLID MECHANICS

Prerequisite: ZZ1001 Engineering Mechanics

Total Hours: 42 L T P C
3 0 0 3
Module 1 (12 hours)
Introduction, general concepts – definition of stress – stress tensor, Stress analysis of axially loaded members,
shear stresses – direct shear problems, Strength based design of members (deterministic method), Axial strains
and deformations in bars, Hooke’s Law – idealized stress-strain relationships – Poisson's ratio, thermal strain,
Saint Venant's principle, Elastic strain energy, Statically indeterminate systems, Strain Tensor, Constitutive
relationships, generalized Hooke's law for isotropic materials, relationships between elastic constants, Thin
walled pressure vessels.
Module 2 (10 hours)
Axial force, shear force and bending moment diagrams – sign conventions, Axial force, shear force and bending
moments by direct approach, integration, Bending stresses in beams, Elastic flexure formula- bending stresses,
Elastic strain energy in bending, Inelastic bending, Bending about both principal axes – Elastic bending with
axial loads, Shear stresses in beams - shear flow - shearing stress formulae.
Module 3 (10 hours)
Torsion - torsion of circular elastic bars, statically indeterminate problems, torsion of inelastic circular bars,
strain energy in torsion, Torsion of thin walled tubes, Deflection of beams - direct integration method,
singularity functions, superposition techniques, moment area method , elementary treatment of statically
indeterminate beams.
Module 4 (10 hours)
Transformation of stresses and strains (two-dimensional case only) - equations of transformation - principal
stresses, Mohr's circles of stress and strain, Strain rosette, Compound stresses - superposition and its
limitations - eccentrically loaded members, Columns - theory of columns - buckling theory - Euler's formula -
effect of end conditions - eccentric loads and secant formula.
References
1. Popov,E.P., Engineering Mechanics of Solids, 2nd ed., Prentice Hall of India, New Delhi, 2000.
2. Beer, F.P.,Johnston, E.R. and DeWolf, J.T.,Mechanics of Materials, 3rd ed., Tata McGraw-Hill.
3. Timoshenko, S.P. and Young, D.H.,Elements of Strength of Materials, McGraw-Hill.
4. Irving H. Shames, Introduction to Solid Mechanics, 2nd ed., Prentice Hall of India.
5. Crandall, S.H., Dahl, N.C. and Lardner, T.J.,Introduction to Mechanics of Solids, McGraw-Hill.

Course Outcomes

CO1: To draw the SF and BM diagrams for various beams under different loading conditions.
CO2: To be able to determine strength and deformation of members under various loading conditions.
CO3: To determine the stability of the columns under different end conditions and understand the design
principles.
CO4: Learn the two dimensional stress transformation and apply it for analysis of members with combined
loading.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2003 ENGINEERING MECHANICS – DYNAMICS

Prerequisite: ZZ1001 Engineering Mechanics

Total Hours: 42 L T P C
3 0 0 3
Module 1 (13 hours)
Review of particle kinematics, Velocity and acceleration in rectangular coordinates – cylindrical coordinates –
path variables, Review of particle dynamics – Newton’s Law for rectangular coordinates – cylindrical
coordinates and path variables, Newton’s Law for system of particles – review of work-energy relations for a
single particle – work-energy equations for system of particles – work-energy expression based on center of
mass, Linear momentum considerations for a system of particles – impulsive forces– impact, Moment-of-
momentum equation for a single particle – moment-of-momentum for a system of particles.
Module 2 (8 hours)
Kinematics of rigid bodies, Translation and rotation of rigid bodies – Chasles’ theorem – derivative of a vector
fixed in a moving reference – applications of the fixed-vector concept – general relationship between time
derivatives of a vector for different references – relationship between velocities of a particle for different
references – acceleration of a particle for different references.
Module 3 (9 hours)
Moments and products of inertia – formal definition of inertia quantities – translation of coordinate axes –
transformation properties of inertia terms – inertia ellipsoid and principal moments of inertia, Kinetics of plane-
motion of rigid bodies,Moment-of-momentum equations – pure rotation of a body of revolution – body with
two orthogonal planes of symmetry –slablike bodies – rolling of slablike bodies, General plane motion of a
slablike body – pure rotation of an arbitrary rigid body – balancing.
Module 4 (12 hours)
Energy and impulse momentum methods for rigid bodies, Kinetic energy of rigid body – work-energy relations
– angular momentum of a rigid body about any point in the body – impulse-momentum equations – impulsive
forces and torques,Eccentric impact, Dynamics of general rigid-body motion – Euler’s equations of motion and
applications – necessary and sufficient conditions for equilibrium of rigid body – three-dimensional motion
about a fixed point – Euler angles – equations of motion using Euler angles – torque-free motion.
References
1. Shames, I.H.,Engineering Mechanics –Statics and Dynamics, 4thed., Prentice Hall of India, 1996.
2. Beer, F.P., and Johnston, E.R.,Vector Mechanics for Engineers, McGraw-Hill, 2000.
3. Meriam, J.L., and Kraige, L.G.,Engineering Mechanics – Dynamics, John Wiley & Sons, 2002.

Course Outcomes

CO1: Ability to formalize real life engineering problems using engineering fundamentals.
CO2: Ability to solve rigid body mechanics problems.
CO3: Ability to solve 3D dynamical problems related with rigid bodies
CO4: Enable the students to study higher level courses like robotics etc.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2101 MATERIALS SCIENCE AND METALLURGY
Prerequisite: Nil L T P C
3 0 0 3
Total Hours: 42
Module 1 (9hours)
Engineering materials: classification, requirements, properties and selection of engineering materials, Review of
fundamentals - Crystal structure,Crystal imperfections,Edge and screw dislocations, interaction between
dislocations, Frank-Reed source. Experimental techniques for metallographic studies, optical microscopy,
electron microscopy (SEM and TEM), X-ray diffraction, grain size, grain size measurement, ASTM grain size
number.
Module 2 (10hours)
Solidification of metals- cooling curves, nucleation-homogeneous and heterogeneous nucleation, supercooling,
critical radius, grain growth, dendritic pattern, equiaxed and columnar grains, grain boundary-grain boundary
effects, solidification and structure of castings-coring, homogenization. Alloys-solid solutions-interstitial,
substitutional ordered and disordered solid solutions, Hume-Rothery rules, intermetallic compounds, phase
diagrams -construction from cooling curves, lever rule, equilibrium diagrams of binary alloys, isomorphous
(Cu-Ni), Eutectic (Bi-Cd, Pb-Sn) detailed study of Fe-C systems. Diffusion: mechanisms of diffusion-Fick's
laws of diffusion-applications.
Module 3 (11 hours)
Deformation of metals - cold working, hot working, annealing of a cold worked article-recovery,
recrystallisation and grain growth, elastic and plastic deformations - mechanisms of plastic deformation,
deformation by slip-slip systems- slip planes and slip directions, critical resolved shear stress, deformation by
twinning. Strengthening mechanisms - work hardening, solid solution hardening, dispersion hardening,
precipitation hardening, grain boundary strengthening. Heat treatment of steels - stress relieving, annealing,
normalising, hardening, TTT diagram, tempering, hardenability, Jominy test. Surface hardening - flame
hardening, induction hardening, Case hardening - carburising, nitriding, cyaniding, etc. Metallic Coatings, hard
facing, metal cladding, anodising, diffusion coatings.
Module 4 (12hours)
Ferrous alloys: steels-alloy steels, tool steels, stainless steels, effect of alloying elements on properties of steels,
cast irons-classification, structure, properties, applications. Non-ferrous alloys - Al and Al alloys, Cu and Cu
alloys, Mg and Mg alloys, Zn and Zn alloys-major types, composition, properties and applications. Non-
metallic materials - thermoplastics, thermosetting plastics, elastomers, composites, ceramics, glasses. Selection
and use of engineering materials, Recent developments in materials science - smart materials, shape memory
alloys, functionally graded materials, piezo-electric materials.
References
1. Smith, O.C., Science of Engineering Materials,3rd ed., Prentice Hall, 1985.
2. Callister, W.D., Materials Science and Engineering: An Introduction, 7th ed., John Wiley & Sons, 2007.
3. Avner, S.H., Introduction to Physical Metallurgy, 2nd ed., McGraw-Hill Inc., 1976.
4. Van Vlack, L.H., Elements of Materials Science and Engineering, 6th ed., Addison Wesley Publishing
Company, 1989.
5. Shackelford, J.F., Introduction to Materials Science for Engineers, 6th ed., Prentice Hall, 2004.
6. Higgins, R.A., Engineering Metallurgy Part I, Applied Physical Metallurgy, 6th ed., Viva Books Private
Limited, 1998.
7. Raghavan, V., Material Science and Engineering, 5th ed., Prentice-Hall of India, 2004.
8. Reed Hill, R.E.,Physical Metallurgy Principles, 2nd ed., Affiliated East-West Press, 2008.
9. Jastrzebski, Z.D., Nature and Properties of Engineering Materials, 2nd ed., John Wiley & Sons, 1976.
10. Charles, J.A., Crane, F.A.A., and Furness, J.A.G., Selection and Use of Engineering Materials, 3rd ed.,
Butterworth Heinemann, 1997.
Course Outcomes

CO1: To train the students to apply fundamental knowledge of basic science for selection and processing of
material for engineering applications.
CO2: To expose the students to various equipment and experimental techniques used in the field of material
science and metallurgy.
CO3: Understand the principles of materials science and metallurgy and to use them for practical applications
like alloying, casting, heat treatment etc.
CO4: Recent developments taking place in the field of material science and metallurgy.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2091 MACHINE DRAWING

Prerequisite: ZZ1002 Engineering Graphics

L T D C
Total Hours: 42 0 0 3 2
Module 1 (9 hours)
Introduction to machine drawing, Principles of orthographic projections applied to machine drawing, First angle
and third angle projections, Methods of dimensioning, Conversion of pictorial projections into orthographic
projections, Sectional views, Rules and conventions of sectioning, Full sectional, half sectional, partial sectional
and revolved sectional views of simple machine parts, Screwed fastenings – screw thread forms – vee and
square threads – nomenclature of threads – conventional representation of threads, Hexagonal and square
headed bolts and nuts, Locking arrangements of nuts, Various types of machine screws and set screws,
Foundation bolts.
Module 2 (9 hours)
Pipe joints – coupler joint – nipple joint – union joint – socket and spigot point – integral and screwed flanged
joints, Shaft joints – cotter and pin joints – socket and spigot joint – gib and cotter joint – sleeve and cotter joint
and knuckle joint, Couplings – muff couplings, flanged couplings, flexible coupling, Oldham's coupling and
universal coupling, Parallel and tapered sunk keys – hollow and flat saddle keys – feather key and pin key,
Bearings – solid journal bearings – bushed bearings – Plummer block – foot step bearing and pedestal bearing.
Module 3 (15 hours)
Assembly drawings – types – accepted norms, I.C. engine parts –piston – connecting rod, Steam Engine parts –
eccentric – stuffing box, Parts of a lathe – tail stock – tool post, Miscellaneous assemblies – vices – screw jack,
Valves.
Module 4 (9 hours)
Surface texture – nomenclature of surface texture – designation of surface texture – selection of surface
characteristics, Limits, fits and tolerances – nomenclature – classification of fits – systems of fits and tolerances
– designation – selection of fits and tolerances, Working/Production drawings – working drawings of simple
machine elements, Computer aided drafting, Simple exercises using CAD Packages.
References
1. Bhatt, N.D., and Panchal, V.M., Machine Drawing, 43rd ed., Charotar Publishing House, 2008.
2. Narayana, K.L., Kannaiah, P., and Reddy, K.V., Machine Drawing,Wiley Eastern, 2005.
3. John, K.C., and Varghese, P.I., Machine Drawing, VIP Publishers, 2009.
4. Gill, P.S., A Text Book of Machine Drawing, Kalson Publishers, 2001.
5. Sidheswar, N., Kannaiah, P., and Sastry, V.V.S., Machine Drawing , Tata McGraw-Hill, 2007.
6. Ajeet Singh,Machine Drawing: Includes AutoCAD, 1st ed., Tata McGraw-Hill, 2010.

Course Outcomes

CO1: To visualize geometric shapes and objects and to apply basic knowledge acquired in engineering graphics
to a specific engineering domain.
CO2: To appreciate intricacies of machine component, assemblies and their functional aspects.
CO3: The concept of geometric dimensioning and tolerancing in order to enable the students to prepare
production drawings.
CO4: To learn use of computers and software tools in machine drawing.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 EE2094 ELECTRICAL MEASUREMENTS AND MACHINES LABORATORY

Prerequisite: Nil L T P C
0 0 3 2
Total Hours: 42

List of Experiments

1. (a) Determination of V-I characteristics of a linear resistor and an incandescent lamp.

(b) Measurement of high and low resistance using Voltmeter/Ammeter method.
2. Measurement of Power in Single phase AC circuit using 3Ammeter, 3 Voltmeter and 1Wattmeter methods and
determination of circuit parameters.
3. Measurement of Energy using single-phase energy meter and verification by power /time measurements.
4. Measurement of power in 3 phase circuits using two-wattmeter method.
5. Determination of the efficiency and regulation of single-phase transformer by direct loading.
6. Open circuit and short circuit tests on a single-phase transformer and determination of efficiency and voltage
regulation at various loads conditions.
7. (a)Study of Starters for 3 phase Induction motors.
(b)Load test on squirrel cage induction motor and determination of its performance characteristics.
8. Load test on slip ring induction motor and determination of its performance characteristics.
9. Determination of Open circuit characteristic and load characteristics of a dc shunt generator.
10. Determination of performance characteristics of a dc shunt motor by conducting load test.
11. Determination of performance characteristics of a dc series motor by conducting load test.
12. Determination of Open circuit characteristic of a 3-phase alternator.

References

1. Clayton & Hancock, Performance & Design Of DC Machines, CBS, 3rd ed., 2001.
2. Langsdorf, A.S., Principles of DC Machines, McGraw-Hill, 6th ed., 1959.
3. Say, M. G, Performance & Design of AC Machines, Pitman, ELBS.3rd ed., 1983.
4. Langsdorf, A.S., Theory of AC Machinery, McGraw-Hill., 2nd ed., 2002.
5. Sawhney, A.K, Electrical & Electronic Measurements & Instrumentation, Dhanpat Rai & Sons, 1996.
6. Soni, Gulpta & Bhatnagar, A course in Electric Power, Dhanpat Rai & Sons.

Course Outcomes

CO1: Acquire hands on experience of conducting various tests on dc machines and obtaining their performance
indices using standard analytical as well as graphical methods.
CO2: Acquire hands on experience of conducting various tests on transformers and obtaining their performance
indices using standard analytical as well as graphical methods.
CO3: Acquire hands on experience of conducting various experiments in electrical measurements.
CO4: Acquire hands on experience of conducting various tests on induction machines and obtaining their
performance indices using standard analytical as well as graphical methods.
Evaluation Weightage (%)
Component
Laboratory 60
Work
End Semester 40
Examination
 SEMESTER 4

MA2002 MATHEMATICS IV
Prerequisite: MA 1001, MA 1002
L T P C
Total Hours: 56 Hrs 3 1 0 3

Module 1Series Solutions and Special Functions (15 Hours)

Power series solutions of differential equations, Theory of power series method, Legendre Equation, Legendre
Polynomials, Frobenius Method, Bessel’s Equation, Bessel functions, Bessel functions of the second kind,
Sturm- Liouville’s Problems, Orthogonal eigenfunction expansions.

Module 2 Partial differential Equations (16 Hours)

Basic Concepts, Cauchy’s problem for first order equations, Linear Equations of the first order, Nonlinear
Partial Differential Equations of the first order, Charpit’s Method, Special Types of first order equations,
Classification of second order partial differential equations, Modelling: Vibrating String, Wave equation,
Separation of variables, Use of Fourier Series, D’Alembert’s Solution of the wave equation, Heat equation:
Solution by Fourier series, Heat equation: solution by Fourier Integrals and transforms, Laplace equation,
Solution of a Partial Differential Equations by Laplace transforms.
Module 3Complex Numbers and Functions (13 Hours)
Complex functions, Derivative , Analytic function, Cauchy- Reimann equations, Laplace’s equation, Geometry
of Analytic functions: Conformal mapping, Linear fractional Transformations, Schwarz - Christoffel
transformation, Transformation by other functions.
Module 4 Complex Integration (12 Hours)
Line integral in the Complex plane, Cauchy’s Integral Theorem, Cauchy’s Integral formula, Derivatives of
analytic functions.Power series, Functions given by power series, Taylor series and Maclaurin’s series.
Laurent’s series, Singularities and Zeros, Residue integration method, Evaluation of real Integrals.

Text Book
Kreyszig E, Advanced Engineering Mathematics, 8th Edition, John Wiley & Sons, New York, 1999 .

Reference Books
1. I.N. Sneddon, Elements of Partial Differential Equations, Dover Publications, 2006.
2 . Wylie C. R. & Barret L. C., Advanced Engineering Mathematics, 6th Edition,
Mc Graw Hill, New York,1995.
3. Donald W. Trim, Applied Partial Differential Equations, PWS – KENT publishing company, 1994.

Course Outcomes

CO1: Acquire the knowledge to solve differential equations using power series and Frobenius method.
CO2: Acquire knowledge about the ability to solve problems using partial differential equations.
CO3: To know the properties of analytic and harmonic functions.
CO4: Understanding Cauchy's integral theorem and its consequences.
CO5: Acquire the knowledge to compute residues and integrals using the residue theorem.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2011 FLUID MACHINERY

L T P C
3 1 0 3
Prerequisite: ME2001 Mechanics of Fluids
Total Hours: 42
Module 1 (11 hours)
Integral form of continuity, momentum and energy equations, Dynamic action of fluids over flat plates and
curved surfaces – Force, work done and efficiency, Dimensional analysis – Rayleigh’s method and
Buckingham’s pi method, Principles of models and similitude as applied to turbo-machines – Non-dimensional
parameters applicable to hydraulic machines like capacity coefficient, head coefficient, power coefficient and
specific speed and as applicable to hydraulics like Reynolds number, Mach number, Froude’s number, Weber’s
number and Euler’s number.
Module 2 (11 hours)
Euler’s equation for turbo-machines, Classification of hydraulic turbines – Constructional features of Pelton,
Francis and Kaplan turbines, Speed regulation and Performance analysisof hydraulic turbines, Model studies,
Theory of draft tubes and cavitations in turbines.
Module 3 (11 hours)
Classification of pumps –Features of rotodynamic and positive displacement pumps,Rotodynamic pumps –
principle of working - Vortex motion – Spiral motion – Constructional features of centrifugal pumps –
Performance analysis - Efficiencies – Classification of centrifugal pumps – Pump characteristics – Theoretical
and actual Head- Capacity relationship – Pump selection, Model studies, Cavitations in pumps.
Module 4 (9 hours)
Positive displacement pumps - Reciprocating pump – principle of working – Effect of acceleration and friction
– Use of air vessels, Cavitation, Pump characteristics. Rotary pumps – Working principle of rotary piston pump,
vane pump and gear pump, Miscellaneous fluid devices – Intensifier and Accumulator, Application to hydraulic
devices –Hydraulic ram.
References:
1. Shepherd D.G., Principles of Turbo machinery, Macmillan Company, New York, 1956.
2. Jagdish Lal, Hydraulic Machines, 6th ed., Metropolitan book Co. private Ltd. New Delhi.
3. Stepanof, A.J., Centrifugal and Axial Flow Pumps, 2nd edition, John Wiley & Sons Inc., New York,
1957.
4. Dixon, S.L, Hall, C.A., Fluid Mechanics and Thermodynamics of Turbo machinery, Pergamon Press, 4th
ed., 1998.
5. John. M. Vance, Rotodynamics of Turbomachinery, Wiley-Interscience Publication, John Wiley & Sons,
1988.
6. Cengel, Y.A, Cimbala, J.M., Fluid Mechanics: Fundamentals & Applications, 2nd ed., McGraw-Hill,
2006.
Course Outcomes

CO1: To utilize the fundamental principles of fluid mechanics and thermodynamics, and apply laws of
conservation of mass, momentum and energy in turbomachines.
CO2: To have a basic understanding of the principles of turbomachines, their construction, way of functioning
and the flow processes that take place in these machines.
CO3: To develop basic skills in drawing and analysis of the velocity triangles at the tips of rotor blades, energy
balance at component and system level, and calculation of the various efficiencies and losses.
CO4: Use dimensional analysis to compare homologous machines, dimensionless numbers applied to
hydraulics and hydraulic machines, design and selection of appropriate hydraulic machines for
appropriate operations.
Evaluation Weightage (%)
Component
Test 1 15
Test 2 20
Assignments 15
End Semester 50
Examination
 ME2012 APPLIED MECHANICS OF SOLIDS

Prerequisite: ME2002 Elements of Solid Mechanics

L T P C
Total Hours: 42 3 0 0 3
Module 1 (11 hours)
Stress at a point, Stress tensor, Stress transformation, Principal stresses – principal planes, Mohr’s circle,
Octahedral stresses, Hydrostatic and pure shear states, Strain at a point – strain tensor, Analogy with stress
tensor.
Module 2 (11 hours)
Equations of elasticity - equation of equilibrium - strain-displacement equations, compatibility conditions -
constitutive equations -Navier equations, Boundary conditions – traction - displacement and mixed boundary
conditions. Special problems in bending - usymmetric bending - shear centre.
Module 3 (10 hours)
Simplification to 2-D problems - plane stress problems - plane strain problems, Axisymmetric problems -
Lame’s problem - rotating disks and shrink fits.Energy Techniques - introduction to energy methods - strain
energy - principle of virtual work - minimum potential energy principle.
Module 4 (10 hours)
Three dimensional problems, Torsion of non-circular sections - St. Venant’s theory - Prandtl’s stress function
approach - elliptical and triangular cross sections, Prandtl’s membrane analogy, Torsion of thin walled open and
closed sections.
Introduction to plasticity - theory of plasticity - yield criteria for metals - stress strain relationships.
References
1. L. S. Srinath, Advanced Mechanics of Solids, Third edition, Tata McGraw Hill, 2003.
2. Den Hartog, Advanced Strength of Materials, McGraw Hill, New York.
3. S.P.Timoshenko and J.N. Goodier, Theory of elasticity, McGraw Hill International Edn., Third Edn.,
1970.
4. A.J. Durelli, E.A. Philips and C.H. Psao, Introduction to the Theoretical and Experimental Analysis of
Stress and Strain, McGraw Hill, New York.
5. Fred B. Seely and Smith, Advanced Mechanics of Materials, John Wiley and sons, New York.
6. W. Johnson, and P. B. Mellor, Engineering Plasticity, Van Nostrand Reinhold, 1973.

Course Outcomes

CO1: Analyze the complex stress and strain in three dimensional body.
CO2: To formulate the mathematical model using governing equations of elasticity.
CO3: To solve torsion problems of non-circular section and thin walled section.
CO4: To obtain the solution of 2D elasticity problems and to understand basic concepts of plasticity problems.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2013 MECHANICS OF MACHINERY

Prerequisite: ZZ1001 Engineering Mechanics

L T P C
Total Hours: 42
3 0 0 3
Module 1 (12 hours)
Introduction to mechanisms, Applications of mechanisms, Kinematics of mechanisms – kinematic diagrams,
Degree of freedom, Position and displacement analysis –graphical methods, Velocity analysis –relative motion
–graphical method – instant center, Mechanical advantage, Acceleration analysis –graphical method.
Module 2 (10 hours)
Analytical methods in mechanism analysis, Computer oriented methods in kinematic analysis, Cam Design,
Cam and follower types, Displacement diagrams, Cam profile synthesis– graphical and analytical methods,
Design of plate cam – reciprocating flat faced follower – roller follower,Advanced cam profile techniques.
Module 3 (10 hours)
Gears –Law of gearing, Involute spur gears – involutometry, Spur gear details –interference – backlash, Gear
standardization,Internal gear, Cycloidal gear, Non-standard gears, Bevel, helical and worm gearing, Gear Trains
–simple and compound gear trains –planetary gear trains –solution of planetary gear train problems –
applications.
Module 4 (10 hours)
Kinematic synthesis, Tasks of kinematic synthesis –type and dimensional synthesis –graphical synthesis for
motion –path generation without and with prescribed timing, Function generation – overlay method, Analytical
synthesis techniques, Complex number modelling – loop closure equation technique – Freudenstein's equation,
Case studies in synthesis of mechanisms.
References
1. Uicker,J.J.Jr., Pennock, G.R., and Shigley, J.E., Theory of Machines and Mechanisms, 3rded.,Oxford
University Press, 2009.
2. Sandor, G.N., and Erdman, A.G., Advanced Mechanism Design: Analysis and Synthesis, Vol. I & II,
Prentice-Hall of India, 1988.
3. Mabie, H.H., and Reinholtz, C.F., Mechanisms and Dynamics of Machinery, 4th ed., John Wiley &Sons,
1987.
4. Ghosh, A, and Mallik, A.K., Theory of Mechanisms and Machines, 3rded., Affiliated East-West Press,
1998.
5. Waldron, K.J., and Kinzel,G.L., Kinematics, Dynamics and Design of Machinery, John Wiley & Sons,
2004.
6. Norton,R.L., Design of Machinery, Tata McGraw-Hill, 2004.
7. Martin, G.T., Kinematics and Dynamics of Machines, McGraw-Hill, 1969.
8. Rattan, S.S., Theory of Machines, 3rded., Tata McGraw-Hill, 2009.
9. Nikravesh, P.E., Planar Multibody Dynamics, CRC Press, 2008.

Course Outcomes

CO1: To familiarize the motion of mechanism- to define a mechanism and to do kinematic construction for
variety of mechanism used in application.
CO2: To introduce basic mechanisms such as slider-crank linkages, four-bar linkage, gear and cam, perform the
motion analysis using both graphical and analytical methods.
CO3: To apply the knowledge gained in the earlier course engineering mechanics to a system of rigid bodies
which are interconnected with constraints.
CO4 : To introduce the concept of synthesis of mechanisms, which helps in the understanding of design.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2014 THERMODYNAMICS

Prerequisite: Nil
L T P C
Total Hours: 42
3 0 0 3

Module 1 (12hours)
Basic concepts of thermodynamics – thermodynamic systems – control volume – properties of a system – state
and equilibrium – processes and cycles – forms of energy – temperature and zeroth law of thermodynamics,
Properties of pure substances – pure substance – phases of a pure substance – phase-change processes of pure
substances – property diagrams for phase-change processes – property tables – the ideal-gas equation of state –
compressibility factor – other equations of state – internal energy, enthalpy, and specific heats of ideal gases.
Module 2 (10hours)
Energy transfer by heat, work, and mass – concept of heat and work – forms of work – flow work and the
energy of a flowing fluid, The first law of thermodynamics – energy balance for closed systems – energy
balance for steady- flow systems – some steady-flow engineering devices – energy balance for unsteady-flow
processes.
Module 3 (10 hours)
The second law of thermodynamics –introduction to the second law –thermal energy reservoirs –heat engines –
Kelvin-Planck statement – energy conversion efficiencies – refrigerators and heat pumps – Clausius statement –
equivalence of the two statements, Reversible and irreversible processes, The Carnot cycle, The Carnot
principles, The thermodynamic temperature scale, The Carnot heat engine, The Carnot refrigerator and heat
pump.
Module 4 (10hours)
Entropy –increase of entropy principle –entropy change of pure substances –isentropic processes –property
diagram involving entropy – the T ds relations – entropy change of liquids and solids – The entropy change of
ideal gases, Exergy, Reversible work and irreversibility, Second law efficiency, Thermodynamic property
relations – the Maxwell relations – the Clapeyron equation – genral relations for du, dh, ds, Cv, and Cp, The
Joule-Thomson coefficient, The h , u , and s of real gases.

References
1. Cengel,Y.A., and Boles, M.A., Thermodynamics: An Engineering Approach, 4th ed., Tata Mc Graw-
Hill, 2003.
2. Sonntag, R.E., and Bornakke, C., Fundamentals of Thermodynamics, 7th ed., John Wiley & Sons,
2009.
3. Moran, M.J., and Shapiro, H.N., Fundamentals of Engineering Thermodynamics, 6th ed., John Wiley &
Sons, 2008.

Course Outcomes

CO1: To provide the foundation for analysis of energy conversion systems.

CO2: To analyze the relations governing thermodynamic properties and its application.
CO3: To assess the performance of engineering systems and processes based on laws of thermodynamics.
CO4: To apply the concepts of entropy and exergy in engineering analysis.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME2111ESSENTIALS OF MANAGEMENT

Prerequisite: Nil L T P C
Total Hours: 42 hours 3 0 0 3

Module 1 (9 Hours)
The management process, Schools of management thought, Kinds of managers – basic managerial roles and
skills– the nature of managerial work, Contemporary management issues and challenges, Basic elements of
planning – types of plans.
Module 2 (9 Hours)
Organizing process, Concepts of authority – responsibility–power–accountability – delegation of authority,
Types of organization structures, Directing, Leading –motivational strategies – communication, Basic elements
of control.
Module 3 (12 Hours)
Managing human resources in organizations, Functions of financial management– classification of capital –
sources of finance – financial statements, Nature of marketing – marketing mix – sales promotion.
Module 4 (12 Hours)
Managerial decision making process – decision criteria under certainty –risk–uncertainty – analytical models of
decision making, Network techniques–critical path method – Programme Evaluation and Review Technique –
time/cost trade-off in critical path networks.
References
1. Koontz, H., and Weihrich, H., Essentials of Management: An International Perspective, 8th ed., McGraw
Hill, 2009.
2. Griffin, R.W., Management: Principles and Applications, Cengage Learning, 2008.
3. Kotler, P., Keller K.L., Koshy, A., and Jha, M., Marketing Management, 13th ed., 2009.
4. Khan, M.Y., and Jain, P.K., Financial Management, Tata-McGraw Hill, 2008.

Course Outcomes

CO1: To learn the fundamentals of management and the various theories of management.
CO2: To learn the functions of management and practice in real world.
CO3: To understand the functional areas of management-Marketing, Finance, HRM and Operational
Management.
CO4: To prepare students to solve decision making problems and project management problems.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
ME2092 FLUID MECHANICS AND FLUID MACHINERY LABORATORY

Prerequisite: ME2001 Mechanics of Fluids

L T P C
Total Hours: 42
0 0 3 2
Study of plumbing tools and pipe fittings, Study of measuring instruments, Measurement of metacentric height
and radius of gyration of a floating body, Calibration of flow measuring devices - venturimeter- orifice meter -
notches and weirs - nozzle meters, Determination of loss of head due to friction in pipes, Verification of
Bernoulli’s theorem, Determination of lift and drag coefficients of cylinder and airfoil, Demonstration of
laminar and turbulent flow in pipes - critical velocity, Forces on curved and plane surfaces, Experiments on
turbines - performance and operating characteristics, Experiments on pumps - centrifugal pumps - reciprocating
pumps - gear pumps, Experiment on torque converter.

Course Outcomes

CO1: Impart knowledge about various flow measuring devices.

CO2: Impart knowledge about calibration of flow measuring equipment.
CO3: Familiarize students about the fluid machineries and its performance characteristics.
CO4: Impart knowledge about the testing of fluid machineries for its performance characteristics.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 CE2095 STRENGTH OF MATERIALS LABORATORY
L T P C
0 0 3 2
Prerequisite: CE2001 Mechanics of Solids or equivalent.

Total Hours: 42

List of Exercises

1. Tension test on MS rod

2. Shear Test on MS rod
3. Torsion test on MS Specimen
4. Hardness tests on metals
5. Impact tests on metals
6. Bending test on steel beams
7. Spring test – open and close coil springs
8. Compression test on cubes and cylinders – determination of modulus of elasticity
9. Study of extensometers and strain gauges

Course Outcomes

CO1: Acquire hands on experience on testing tension and shear properties of materials.
CO2: Acquire hands on experience on testing torsional properties of materials.
CO3: Acquire hands on experience on testing hardness of metals using various hardness testing machines.
CO4: Acquire hands on experience on testing the impact and bending strength of materials.
CO5: To familiarize the uses of extensometer and strain gauges.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 SEMESTER 5

ME3001 DYNAMICS OF MACHINERY

Prerequisite: ME2013 Mechanics of Machinery L T P C
Total hours: 42 3 0 0 3
Module 1 (10 Hours)
Static force analysis of machines, Static force analysis with friction, Force analysis of gears, spur ─helical
─bevel, Method of virtual work, Dynamic force analysis, Principle of super position, Complex algebra method.
Module 2 (12Hours)
Balancing ─ Static and dynamic unbalance, Balancing of rotating masses – Balancing machines, Balancing of
single cylinder engines – Balancing of multi cylinder engines – Balancing of V and radial engines, Balancing of
linkages, Gyroscopes and its applications, Cam dynamics, Governors, Flywheels.
Module 3 (10Hours)
Recap of the Single DOF vibration systems– free and forced vibration – equivalent viscous damping, Transient
vibration, Rotating unbalance, Support excited vibration, Critical speed of shafts,Vibration measuring
instruments,Vibration of two DOF systems – formulation-normal mode analysis – solution of matrix Eigen
value problem.
Module 4 (10 Hours)
Two DOF ─Forced harmonic vibration, Vibration absorber, Multi DOF systems ─matrix formulation,
Lagrange’s equation, Introduction to vibration of continuous systems ─vibration of string, Approximate
methods – Rayleigh’s energy method ─Dunkerley's equation, Holzer’s method, Geared system.
References
1. Uicker,J.J. Jr., Pennock, G.R., and Shigley, J.E., Theory of Machines and Mechanisms, 3d
ed.,OxfordUniversity Press, 2009.
2. Mabie, H.H., and Reinholtz, C.F., Mechanisms and Dynamics of Machinery, 4d ed., John Wiley & sons,
1987.
3. Ghosh, A, and Mallik, A.K., Theory of Mechanisms and Machines, 3d ed., Affiliated East-West Press,
1998.
4. Holowenko, A.R., Dynamics of Machinery, John Wiley & Sons, 1965.
5. Waldron, K. J., and Kinzel,G. L., Kinematics, Dynamics and Design of Machinery, John Wiley & Sons,
Inc., 2004.
6. Norton,R.L., Design of Machinery, Tata McGraw-Hill, 2004.
7. Rattan, S.S., Theory of Machines, 3d ed., Tata McGraw-Hill, 2009.
8. Nikravesh, P.E., Planar Multibody Dynamics, CRC Press, 2008.
9. Thomson, W.T., Dahleh, M.D., and Padmanabhan, C, 5d ed.,Theory of Vibrations with Applications,
Pearson Education, 2008.
10. Meirovitch, L., Elements of Vibration Analysis,2d ed., McGraw-Hill, 2007.
11. Den Hartog, J.P., Mechanical Vibrations, 4d ed., McGraw-Hill, 1985.

Course Outcomes

CO1:To learn force analysis of machines which is an essential requirement in the design of machines.
CO2:To learn the methods and nature of transmission forces using a system of interconnected bodies and to
integrate this with transmission of motion .
CO3: To apply the knowledge gained in the course on Engineering dynamics and Mechanics of machinery to
the area of machines.
CO4: To learn the mechanical vibration as a specialized area in dynamics.
.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3002 PRINCIPLES OF HEAT TRANSFER
Prerequisite: Nil L T P C
Total Hours:42 3 0 0 3

Module 1 (10 hours)

Heat transfer - basic modes of heat transfer , conduction heat transfer , energy balance -integral and differential
approaches , general heat conduction equations in Cartesian, cylindrical and spherical coordinates - initial and
boundary conditions - one-dimensional steady state conduction with and without heat generation , temperature
dependence of thermal conductivity , introduction to two dimensional steady state conduction, unsteady state
heat conduction in one dimension - lumped heat capacity system , semi infinite solids with sudden and periodic
change in surface temperature

Module 2 (12 hours)

Convective heat transfer - Newton's law of cooling , Prandtl number, hydrodynamic and thermal boundary layer
equations, laminar forced convection heat transfer from flat plates - similarity and integral solutions , internal
flow and heat transfer - fully developed laminar flow in pipes , turbulent forced convection - Reynolds analogy ,
empirical relations in forced convection , natural convection - similarity and integral formulation of natural
convection heat transfer from vertical plates , empirical relations in free convection., Condensation and boiling -
film and drop wise condensation - film boiling and pool boiling, empirical relations for heat transfer with phase
change, Introduction to mass transfer- Fick's law of diffusion – mass transfer coefficient - analogy between
momentum, heat and mass transfer.

Module 3 (10 hours)

Radiation heat transfer – electromagnetic radiation spectrum, thermal radiation, black body, gray body and
white body, monochromatic and total emissive power, Planck’s law, Stefan-Boltzmann law , Wein's
Displacement law , absorptivity , reflectivity , transmissivity , emissivity , Kichhoff's identity , radiation
exchange between surfaces - shape factors for simple configurations , heat transfer in the presence of re-
radiating surfaces , radiation shields, surface and shape resistances , electrical network analogy.

Module 4 (10 hours)

Applications of heat transfer like extended surfaces, critical insulation thickness, heat exchangers, heat pipes
etc. Analysis of fins with constant area of cross section, Heat Exchangers- LMTD, correction factors, heat
exchanger effectiveness and number of transfer units.-Design of heat exchangers –Compact heat exchangers ,
introduction to Heat pipes and their applications. Applications of radiative heat transfer, Multiple- mode heat
transfer problems.

References
1 Holman, J.P., Heat Transfer, 9th ed., Tata McGraw Hill, 2005.
2 Incorpera, F.P. and De Witt, D.P., Fundamentals of Heat and Mass Transfer, John Wiley.
3 Kreith, F., Heat Transfer, International Text Book Company.
4 Gebhart, B., Heat Transfer, McGraw Hill.
5
Course Outcomes

CO1: Understanding the physics involved in various heat transfer mechanisms.

CO2: Applying the knowledge of mathematics, and analyze the different situations in which heat transfer is
involved.
CO3: To be able to calculate heat transfer rate, time required for heating or cooling and obtaining the
temperature distribution with respect to the domain of analysis under different situations.
CO4: To gain the knowledge of applications of heat transfer and to evaluate the design and analysis of different
heat exchangers.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3101 MANAGEMENT OF PRODUCTION SYSTEMS
Pre-requisite: Nil
Total Hours: 42 L T P C
Module 1 (12 Hours) 3 0 0 3
Types of production systems, Modern production management systems, Decisions in production management,
Forecasting, Time series analysis – components of time series – moving average – simple exponential
smoothing, Simple regression, Error measurement – tracking signal, Production planning and control –
framework, Material requirement planning (MRP) – technical issues – system dynamics, Production activity
control.
Module 2 (10 Hours)
Inventory control, Functions of inventor, Inventory problem classification, Relevant cost, Selective inventory
control, Independent demand systems – deterministic models – sensitivity analysis – quantity discount – batch
production – Introduction to probabilistic models, Basic concepts of supply chain management.
Module 3 (10 Hours)
Facilities Planning, Objectives of facility planning, Facilities planning strategies, Assembly chart, Operation
process chart, Scrap and equipment estimation, Facility design – management and planning tools – flow, space
and activity relationship – flow patterns, Layout planning, Systematic layout planning, Types of layout –
process layout – product layout – group technology layout – retail service layout, Reading assignments on
method study and time study.
Module 4 (10 Hours)
Quality management, Quality costs, Introduction to TQM, Introduction to six sigma, Statistical process control,
Control charts for variables – X-bar and R chart, Control charts for attributes – P and C chart, Introduction to
acceptance sampling.
References
1. Chase, R.B., Shanker, R., Jacobs, F.R. and Aquilano, N.J., Production & Supply Management,12th ed., Tata
McGraw-Hill Edition, 2010.
2. Tersine, R.J., Principles of Inventory and Materials management, 4th ed., Prentice-Hall International, 1994.
3. Vollmann, Berry, Whybark and Jacobs, Manufacturing Planning and Control for Supply Chain
Management, 5th ed., Tata McGraw-Hill Edition, 2005.
4. Tomkins, White, Bozer, Frazelle, Tanchoco and Trevino, Facility Planning, 2nd ed., John Wiley & Sons,
1996.
5. Grant, E.L, and Leavenworth, R.S., Statistical quality Control, 7th ed., McGraw-Hill, 1996.

Course Outcomes

CO1:To comprehend the role of operations management in the overall business strategy of the firm.
CO2: To describe the concepts and methods related for designing and managing operations in a production
system.
CO3:To demonstrate the tools appropriate for analysis in demand forecasting, production planning, facility
planning and quality control.
CO4:To evaluate the operations management problems using the appropriate tools.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3102 MANUFACTURING SCIENCE

Prerequisite: Nil
L T P C
Total Hours: 42 3 0 0 3
Module 1 (11 hours)
Foundry: foundry materials- moulding and core sand- binders - additives, sand preparation- sand control tests,
pattern and pattern making, mould and core making, expendable and non expendable moulds, mould assembly,
melting furnaces and melting practice, pouring and fettling, solidification of pure metals and alloys, grain
growth.
Module 2 (11 hours)
Casting processes- sand casting, shell moulding, investment casting, slush casting, gravity and pressure die
casting, centrifugal casting, casting design, gateway system design, riser design casting alloys, casting defects,
inspection, testing- destructive and non-destructive, casting alloys, economics of casting.
Module 3 (10 hours)
Yield criteria of metals (von Mises, Tresca), representation in stress space, isotropic hardening, kinematic
hardening. Plastic stress strain relationship. Metal forming Operations, Principle, process and equipment for
drawing, extrusion, rolling, forging. Analysis of forming operations - load calculation for drawing, extrusion,
rolling, forging.
Module 4 (10 hours)
Metal joining- classification, welding heat sources, arc welding machines, arc production, arc characteristics,
metal transfer, welding electrode, gas welding, resistance welding, thermit welding, ultrasonic welding, electron
beam welding, laser beam welding, gas and arc cutting. Welding metallurgy, weldability of ferrous and non-
ferrous metals, design of weldments, joint design, residual stresses and distortion, testing of welded joints,
brazing and soldering.
References
1. Ghosh, A., and Mallik, A.K., Manufacturing Science, Affiliated East west Press Ltd, 2001.
2. Heine, R., Loper, C., and Rosenthal, P., Principles of Metal Casting, Tata McGraw Hill, 2004.
3. Little, R.,Welding and welding Technology, Tata McGraw Hill, 2004.
4. Kalpakjian, S., Manufacturing Engineering & Technology, Addison Wesley Longman Limited, 1995.
5. Hoffman, O., and Sachs, G., Introduction to Theory of Plasticity for Engineers, McGraw-Hill Book
Company, 1953.
6. Flemings, M.C., Solidification Processes, McGraw Hill, American Welding Society, Welding Hand Book.
7. Doyle, L.E., Manufacturing Processes and Materials for Engineers, 3rd ed., Prentice Hall of India, 1984.
8. Taylor, H.F., Flemings, M.C., and Wulff, J., Foundry Engineering, 1sted., John Wiley & Sons Inc, 1959.
9. Metals Hand Book – Vol. 5, Welding Institute of Metals, USA.

Course Outcomes

CO1:Understanding about foundry casting.

CO2: Learn about advanced casting techniques.
CO3: Understanding different welding techniques and operations.
CO4:Understanding the basic operations and metallurgical processes in soldering and brazing.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3003 ENVIRONMENTAL STUDIES FOR MECHANICAL ENGINEERS

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3

Module 1 (9 hours)
Scope and importance of Environmental Studies, Ecosystems – Structure and function, Forest, Grassland and
Desert ecosystems, diversity in ecosystems, Value of biodiversity, Threats to biodiversity – Wildlife Protection
Act – Forest Conservation Act, Conservation of biodiversity, Environmental ethics, Climate change, global
warming, acid rain, ozone layer depletion, nuclear accidents and holocaust.
Module 2 (11 hours)
Natural resources and associated problems: Forest resources, Aquatic ecosystems, Water resources, Mineral
resources, Land resources, Causes, effects and control measures of Water pollution, Soil pollution and Marine
pollution, Water (Prevention and control of Pollution) Act, Water conservation, rain water harvesting,
watershed management, Disaster management: floods, earthquake, cyclone and landslides, Solid Waste
Management: Causes, effects and control measures of urban and industrial wastes, Wasteland reclamation –
Consumerism and waste products.
Module 3 (10 hours)
Environmental Pollution – Definition – Causes, effects and control measures of: - Air Pollution, Noise
pollution, Thermal pollution and nuclear hazards, Environmental Protection Act – Air (Prevention and Control
of Pollution) Act – Issues involved in enforcement of environmental legislation.
Module 4 (7 hours)
Renewable and non-renewable resources, Growing energy needs, renewable and non-renewable energy sources,
use of alternate energy sources, From Unsustainable to Sustainable development – Urban problems related to
energy, Role of an individual in conservation of natural resources, equitable use of resources for sustainable
lifestyles – Role of Information Technology in Environment and human health.

Field work (Equal to 5 lecture hours)

Visit to a local area to document environmental assets-river/forest/grassland/hill/mountain – Visit to a local
polluted site – Urban/Rural/Industrial/Agricultural – Study of common plants, insects, birds – study of simple
ecosystems-pond, river, hill slopes, etc.
References
1. Agarwal, K.C., Environmental Biology, Nidi Publ. Ltd., Bikancr, 2001.
2. Bharucha Erach, The Biodiversity of India, Mapin Publishing Pvt. Ltd, Ahmedabad, India.
3. Brunner, R.C., Hazardous Waste Incineration, McGraw-Hill Inc.480p. , 1989.
4. Clark, R.S., Manne Pollution, Clanderson Press Oxford.
5. Cunningham, W.P., Cooper, T.H., Gorhani, E., and Hepworth, M.T., Environmental Encyclopedia, Jaico Publ. House,
Mumbai, 1196p., 2001.
6. De A.K., Environmental Chemistry, Wiley Eastern Ltd.
7. Gleick, H.P., Water in crisis, Pacific Institute for Studies in Dev. Environment and Security. Stockholm Env. Institute.
Oxford Univ. Press, 473p., 1993.
8. Heywood, V.H and Watson, R.T., Global Biodiversity Assessment, Cambridge Univ. Press, 1140p. 1995.
9. Jadhav, H and Bhosale, V.M.. Environmental Protection and Law, Himalaya -Pub. House, Delhi 284 p. 1995.
10. Mckinney, M.L.,and Schocr, R.M, 199p.,EnvironmentalScience systems and Solutions, Web enhanced edition. 63.9p.
11. Mhaskar, A.K, Matter Hazardous, Techno-Science Publications.
12. Miller, T.G. Jr., Environmental Science, Wadsworth Publishing Co.
13. Odum, E.P., Fundamentals of Ecology, W.B., Saunders Co.,USA, 574p., 1971.
14. Rao,M.N, and Datta,A.K., Waste Water treatment. Oxford & IBH Publ. Co., 345p. 1987.
15. Sharma, B.K., Environmental Chemistry, Goel Publ. House,Meerut, 2001.
16. Townsend, C., Harper, J, and Michael Begon, Essentials of Ecology, Blackwell Science.
17. Trivedi, R.K., Handbook of Environmental Laws, Rules, Guidelines, Compliances and Standards, Vol. I and II, Enviro
Media (R).
18. Trivedi , R.K., and Goel, P.K., Introduction to air pollution, Techno-Science Publications.
19. Wagner, K.D., Environmental Management, W.B. Saunders Co., Philadelphia, USA, 499p., 1998.
Course Outcomes

CO1: To understand the significance of ecosystem.

CO2:.To understand the significance of natural resources.
CO3:.To understand different environmental pollution control methods.
CO4: To understand the significance of renewable energy sources.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3091 HEAT TRANSFER LABORATORY
L T P C
Prerequisite : Nil
0 0 3 2
Total Hours: 42
Thermal conductivity of a metal rod, Unsteady state conduction heat transfer, Forced convection heat transfer,
Emissivity measurement, Natural Convection heat transfer, Drop wise and film wise condensation, Boiling Heat
transfer, Fins, Vapour Compression Refrigeration System, Heat exchangers, Interferometric measurement of
temperature field.

Course Outcomes

CO1: To familiarize various models of study state heat transfer like conduction, convection (free of force) and
radiation.
CO2: To familiarize heat transfer processes like boiling, condensation and refrigeration systems.
CO3: To familiarize the unsteady state heat transfer processes and heat transfer processes and heat exchangers.
CO4: To find various properties like thermal conductivity and also extended surfaces.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 ME3191 PRODUCTION ENGINEERING LABORATORY I
L T P C
Prerequisite: Nil
0 0 3 1
Total Hours: 42
Classifications of machine tools and machining processes - Specification of machine tool, power source, Centre
lathe - general features, parts and functions - Machining on Centre lathe- Cutting tools - Materials, types:
Grinding, Cutting variables - Selection of speeds, feeds and depth of cut - Use of cutting fluids - Methods of
holding work - Lathe operations - straight, taper and eccentric turning, thread cutting, drilling, boring, profile
turning, knurling - Tolerance and surface finish.
References
1. Chapman, W.A.J., Workshop Technology Vol II, 4th ed., CBS Publishers & Distributors, 2007.
2. Boothroyd, G., Fundamentals of Metal Machining and Machine Tools, McGraw Hill, 1975.
3. Henry, B.D., Aaron, A., and James, A., Machine Tool Operations, Vol II, 4th ed., Tata McGraw Hill, 1960.
4. Chowdhary, H., Workshop Technology Vol II – Machine Tools, Media Promoters and Publishing.
5. HMT, Production Technology, Tata McGraw Hill, 2004.

Course Outcomes

CO1: To substantiate of the basic manufacturing processes learnt through workshop practice II by practical
experiences.
CO2: Practice the operations- shaping, slotting, grinding, milling, and use of lathe for complex product making.
CO3: To learn the preparation of process chart, importance of reducing idling time, movement times and
storage times.
CO4: Use of measuring devices, providing tolerances and allowances.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 SEMESTER 6
ME3111 MACHINING SCIENCE AND MACHINE TOOLS
Prerequisite: Nil
L T P C
Total Hours: 56 4 0 0 4
Module 1 (14 hours)
Kinematic elements in metal cutting. Tool nomenclatures. Mechanics of chip formation, orthogonal and oblique
cutting, shear angle, velocity relationship. Merchant's analysis of cutting forces, cutting power estimation.
Inserts-chip groove geometries: nomenclature, selection and applications in turning, milling, drilling. Carbide
grade design, carbide coatings. Advances in cutting tool materials. Effect of cutting variables on forces. Tool
failure analysis, theories of tool wear, measurement of tool wear. Tool dynamometers, thermal aspects of
machining, Tool life and economics of machining, CNC machining. Micro machining.

Module 2(14 hours)

Basic concepts of machine tools: Tool - work motions, machine tools for various machining processes,
kinematics of machine tools and gear boxes, feed and speed mechanism, machine tool drives, machine tool
dynamics, gear manufacture- milling, hobbing and shaping, special purpose machine tools, hydraulic control of
machine tools, components of hydraulic circuits, control circuits and their characteristics, testing of machine
tools for positioning accuracy and repeatability.
Module 3 (14 hours)
CNC machine tools, constructional features, drives and controls, stepper motors, servo motors, hydraulic
systems, feed back devices, counting devices, interpolators- linear, circular interpolation and other emerging
techniques, adaptive control systems for turning and milling, CNC part programming, post processors, CNC
programming with interactive graphics, use of various software packages, development of CNC programmes
for special problems. Introduction to robotics.
Module 4(14 hours)
Modern machining processes: Mechanics of AJM, EDM, USM, EBM and ECM, process parameters and
applications. Jigs and fixtures, basic principles of location, type and mechanics of locating and clamping
elements, design of jigs and fixtures.
References
1. Ghosh, A., and Mallik, A.K., Manufacturing Science, Affiliated East west Press Ltd, 2001.
2. Juneja, B.L., Sekhon, G.S., and Seth, N., Fundamentals of Metal Cutting and Machine Tools, 2nd ed., New Age
International Publishers, 2003.
3. Sen and Bhattacharya, Principles of Machine Tools, New Central Book Agency (P) Ltd, 1975.
4. Bhattacharyya, A., Metal Cutting: Theory and Practice, New Central Book Agency (P) Ltd, 1984.
5. Shaw, M.C., Metal Cutting Principles, 2nd ed., Oxford University Press, 2005.
6. HMT, Production Technology, Tata McGraw Hill, 2004.
7. Kalpakjian, S., Manufacturing Engineering & Technology, Addison Wesley Longman Limited, 1995.
8. Mehta, N.K., Machine Tool Design and Numerical Control, 2nd ed., Tata Mc Graw Hill, 1996.
9. Boothroyd, G., Fundamentals of Metal Machining and Machine Tools, McGraw Hill, 1975.
10. ASTME, Fundamentals of Tool Design, Prentice-Hall of India.
11. Chapman, W.A.J., Workshop Technology: Vol. 1, Vol. 2, Vol.3,CBS Publishers & Distributors.
12. Khaimovich, Y.M., Hydraulic control of Machine tools, Pergamon Press.
13. Esposito, A., Fluid Power with Applications, 7th ed., Pearson Education, 2008.
14. Ernest, W., Oil Hydraulics Power and its Industrial Applications, 2nd ed., McGraw Hill Book Company, 1960.
15. Kempster, M.H.A., An Introduction to Jig and Tool Design, 3rd ed., Butterworth-Heinemann Ltd, 1974.
16. Donaldson, C., LeCain, G.H., and Goold,V.C., Tool design, 3rd ed., Tata Mc Graw Hill, 1973.
17. Koren, Y., Computer Control of Manufacturing Systems, Mc Graw Hill Book Company, 1986.
18. Groover, M.P., Automation, Production Systems, and Computer-Integrated Manufacturing, 3rd ed., Pearson Education,
2008.
19. Fu, K.S., Gonzalez, R.C., and Lee, C.S.G., Robotics, Control, Sensing, Vision and Intelligence, 1st ed., McGraw-Hill
Book Company, 1987.
Course Outcomes

CO1: Learn basic tool geometry, mechanism of metal cutting, new tool, tool life, cutting force.
CO2:.Learn kinematic of machining tools of various manufacturing methods.
CO3: Understand various modern machining process and its applications.
CO4: Learn basics of jigs and fixtures and design.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3112 METROLOGY AND INSTRUMENTATION

Prerequisite: Nil
L T P C
Total Hours: 42 3 0 0 3
Module 1 (12 hours)
Measurement fundamentals: Units of measurement, terms used in measurement. Measurement uncertainty-
Introduction, Standard deviation as a measure, combining standard uncertainties. Statistical concepts- Sampling,
least squares model, covariance and correlation. Calculation of uncertainties- Law of propagation, correlated
inputs, probability densities, sampling distributions, case studies and problems.
Module 2(10hours)
Experiment planning: Factors, Interference, Randomization, Repetition and Replication, Concomitant methods.
Dynamic characteristics: General model, Zero order, First order- Step response and Frequency response, Second
order- Step response and frequency response, Experimental determination of parameters.
Module 3(10hours)
Metrology: Dimensional and angular measurement - Slip gauges, Comparators, Abbe’s principle. Pneumatic
transducer, Electronic transducers, Sine bar, angle gauges. Surface finish- Parameters, Stylus instruments.
Module 4 (10hours)
Instrumentation: Strain measurement- Resistance & semiconductor strain gauges, circuits and arrangements.
Pressure measurements- Manometers, Elastic transducers. Force & Torque measurements. Temperature
measurement- Expansion thermometers, Resistance Temperature Detectors, Thermistors, Thermocouples,
radiative measurements.
References
1. Kirkup, L., and Frenkel, R.B., An Introduction to Uncertainty in Measurement Using the
GUM,CambridgeUniversity Press, 2006.
2. Doebelin, E.O., Measurement Systems, 5th ed., McGraw-Hill International, 2004.
3. Collett, C.V., and Hope, A.D., Engineering Measurements, 2nd ed., ELBS/Longman, 1983.
4. Beckwith, T.G., Marangoni, R.D., and Lienhard, J.H., Mechanical Measurements, 5th ed., Pearson
Education, 1993.
5. Galyer, J.F.W., and Shotbolt, C.R., Metrology for Engineers, 5th ed., Thomson Learning, 1990.
6. Holman, J.P., Experimental Methods for Engineers, 7th ed., McGraw-Hill Company, 2000.

Course Outcomes

CO1: Understand the terminology.

CO2:.Know the available instruments.
CO3: Quantify the measurement uncertainty.
CO4: Plan experiments.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3011 GAS DYNAMICS

Prerequisite: ME2001 Fluid Mechanics L T P C

3 0 0 3
Total Hours: 42
Module 1 (10 hours)
Basic equations of fluid flow, Reynolds transport equation, Integral and differential formulations - Integral form
of the equations of continuity - Momentum - energy equations - use of the integral equations, Differential form
of these equations, Stokes postulates and constitutive equations, Navier-Stokes equations and energy equations
for Newtonian fluids.
Module 2 (11 hours)
Introduction to compressible flows, Basic concepts - equations for one-dimensional flow through stream tubes -
variation of pressure - temperature - density in the atmosphere, Speed of sound , Mach number, Qualitative
difference between incompressible, Subsonic and supersonic flows, Karman’s rules of supersonic flows,
Characteristic velocities, The adiabatic flow ellipse, Isentropic flow through a duct - criterion for acceleration
and deceleration -stagnation quantities -isentropic relations, Use of gas tables and charts, Operation of nozzles
at off-design conditions.
Module 3 (11 hours)
Normal shocks in one-dimensional flow - occurrence of shocks -analysis of normal shocks - Prandtl’s equation -
Rankine - Hugoniot equation and other normal shock relations -moving shocks, Oblique shocks and expansion
waves -oblique shock relations ---M relations -shock polar, Supersonic flow over a wedge - expansion waves
- Prandtl- Meyer function -intersection of shocks - detached shocks - Mach deflection -shock expansion theory.
Module 4 (10 hours)
Flow with friction - Fanno lines and Fanno flow relations, Effect of friction on properties -choking, isothermal
flows, Flow with simple heat transfer - Rayleigh lines -effect of heat addition -thermal choking, Generalised on
dimensional flows - One-dimensional flow with several effects like mass addition -friction and heat transfer.
References
1. Anderson,J.D., Modern Compressible Flow with Historical Perspective,2nded., McGraw Hill,1990.
2. Shapiro A.H., Dynamics and Thermodynamics of Compressible Fluid Flow, Vol.1, 1st ed., Wiley,
1953.
3. Zuckrow M.J. and Hoffman. J.D., Gas Dynamics, Vol.1, Wiley, New York.1976.
4. Zucker,R.D., and Biblarz.O., Fundamentals of Gas Dynamics, 2nd ed., John Wiley & Sons, 2002.
5. Liepmann,H.W., and Roshko,A., Elements of Gas Dynamics, First South Asian Edition, Dover
Publications,2007.

Course Outcomes

CO1: To give the basic foundation in integral an differential formulations of equations of continuity,
momentum and energy.
CO2: To understand the effect of compressibility aspects in practical applications.
CO3: To analytically solve the flow and heat problems in compressible gases.
CO4: To understand the irreversibility mechanisms of a moving compressible fluid.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3012 THERMAL ENGINEERING I
L T P C
3 1 0 3

Prerequisite : Nil

Total Hours: 42

Module 1 (10 Hours)

Analysis of Gas power cycles, Value of Carnot cycle in engineering, Air standard cycles - assumptions – Otto -
Diesel & Dual combustion cycles, Comparison among these cycles, Miller and Stirling cycles, Real air-fuel
cycles, SI engine cycle at part throttle and supercharged conditions, Four stroke and Two stroke engines, Valve
timing & Port timing diagrams, Scheme of scavenging - Scavenging efficiency.
Module 2 (11 Hours)
Classification of IC engines - Terminology, variables and abbreviations. Simple Carburettor, Fuel Injection
Pump and Injectors.Engine systems– Intake and Exhaust, Transmission, Cooling, Lubrication, Ignition, Starting
systems. Thermochemistry - Fuels for IC engines, Stoichiometric air, Equivalence Ratio, Self Ignition
temperature, Ignition lag (delay), Normal combustion in SI engines, Engine knock – effect of variables on
tendency to knock – Octane Number – Pre-ignition.
Module 3 (11 Hours)
Normal combustion in CI engines, Diesel knock – Cetane Number, Alternate fuels for diesel engines - Multiple
Port Fuel Injection (MPFI), Throttlebody fuel Injection - IC Engine performance – constant speed and variable
speed characteristics - Different methods to determine Friction Power – Variation of volumetric efficiency with
speed and load, Heat Balance, Engine Emission and Air pollution – Catalytic converters and EGR.

Module 4 (10 Hours)

Analysis of Gas Turbine cycles - Brayton cycle, Regeneration - Reheat and Inter cooled cycles – Ericsson cycle
– Ideal Jet – propulsion cycles, Modifications to turbojet engines, Actual Brayton cycle, Open and Closed
cycles, Combustion chambers for gas turbines, A/F ratio and stability loop, Centrifugal and axial flow
compressors.

References

1. Yunus A. Cengel and Michael A. Boles, Thermodynamics – An engineering approach, 3rd ed., Mc Graw-hill
Professional, 1998
2. Willard W and Pulkrabek, Engineering Fundamentals of Internal combustion Engines,2nd ed., Phi Learning.,
New Delhi, 2009
3. Henry Cohen, Rogers G. F. C and SaravanamuttooH. I. H, Gas Turbines Theory, 4th ed., Heritage Publishers,
1996
4. John B. Heywood, Internal Combustion Engine Fundamentals, 1st ed., McGraw-Hill, 1998.
5. Mathur L. and. Sharma R. P, A Course in Internal combustion Engines, 7th ed., Dhanpat Rai Publications (P)
Ltd.,
1999

Course Outcomes

CO1: To understand the significance of thermodynamic cycle w.r.t IC/EC engines

CO2: To determine the performance of engine.
CO3: To understand the working of compressor.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME3192 METROLOGY AND INSTRUMENTATION LABORATORY

L T P C
Prerequisite: Nil 0 0 3 1
Total Hours: 42

1. Calibration and determination of uncertainties of the following:

(a) Strain gauge load cells (b) Bourdon tube pressure gauge (c) LVDT (d) Thermocouple (e)
Tachometers using stroboscopes, etc.
2. Measurement of thread parameters using Universal Measuring Microscope, three wire method, thread pitch
micrometer
3. Evaluation of straightness using autocollimator, spirit level
4. Measurement of tool angles of single point tool using TMM
5. Measurement of gear parameters using Profile projector
6. Study and measurement of surface finish using surface roughness tester
7. Study and measurements with CMM
8. Experiments on limits and fits
9. Study and use of ultrasonic flaw detector
10. Exercises on measurement system analysis
11. Study and making measurements with thread pitch micrometer, disc micrometer, thread pitch gauge, height
gauge, slip gauges, optical flat, three pin micrometer, pyrometer, RTD, Sling psychrometer, zoom
microscope, etc.

Course Outcomes

CO1: Conduct simple experiment.

CO2:.Familiarize with measuring instruments.
CO3: Read instruction manuals and operate equipment.
CO4: Prepare manuals.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 ME3193 PRODUCTION ENGINEERING LABORATORY II

Prerequisite: Nil L T P C
0 0 3 1
Total Hours: 42

Introduction: Limits and Fits, Horizontal and Vertical milling machine – Spindle drives and feed motion -
Milling cutters – indexing head – Simple, compound and differential indexing, shaping machine - cutting
motion, slotting machine, Grinding machine – Surface, cylindrical and centreless grinding – Tool and cutter
grinder, unconventional machining, NC/CNC machine.
Exercises:
Shaping and slotting Exercises -Flat and bevel surfaces, grooves, Slots, guide ways, key ways etc. Exercises in
horizontal and -surface, slot, key way and gear milling-Vertical milling machine. Turning Exercises-Limits and
Fits. Grinding Exercises. Non – traditional Machining, NC/CNC Machining.
References
1. HMT, Production Technology, Tata McGraw Hill, 2004.
2. ASTME, Tool Engineer’s Handbook.
3. Chapman, W.A.J., Workshop Technology:Vol. 2, Vol.3,CBS Publishers & Distributors.
4. Rao, P.N., Manufacturing Technology: Metal Cutting & Machine Tools, 2nd ed.,Tata McGraw Hill, 2008.
5. Groover, M.P., and Zimmers, E.W., CAD/CAM: Computer-Aided Design and Manufacturing, 1984.
6. Mehta, N.K., Machine Tool Design and Numerical Control, 2nd ed., Tata McGraw Hill, 1996.

Course Outcomes

CO1: Fabricate a kinematic linkage with the knowledge acquired through Production Engineering Lab 1.
CO2:.Design a system, fabricate with proper selection of material and operations.
CO3: Present with the applications and problems faced in fabrication.
CO4: Learn the basics in costing and estimating by the analysis of: time, material cost, MHR, and other factors.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 SEMESTER 7

ME4001 MACHINE DESIGN – I

Prerequisite: ME2002 Elements of Solid Mechanics

L T P C
Total Hours: 42
3 0 0 3
Module 1 (12 hours)
Introduction to Design – steps in design process – design factors, Principles of standardization, Selection of
materials, Statistical considerations in design, Stress concentration, Theories of failure, Impact load, Fatigue
loading, Consideration of creep and thermal stresses in design.
Module 2 (10 hours)
Threaded fasteners – thread standards – stresses in screw threads – analysis of power screws – bolted joints –
preloading of bolts – gasketed joints – eccentric loading, Riveted joints – stresses in riveted joints – strength
analysis – boiler and tank joints – structural joints,Keys and pins – types of keys and pins – stresses in keys and
pins – design of cotter and pin joints.
Module 3 (10 hours)
Welded joints – types of welded joints – stresses in butt and fillet welds – torsion and bending in welded joints
– welds subjected to fluctuating loads – design of welded machine parts and structural joints, Springs – stresses
in helical springs – deflection of helical springs – extension, compression and torsion springs – design of helical
springs for static and fatigue loading – critical frequency of helical springs – stress analysis and design of leaf
springs.
Module 4 (10 hours)
Power shafting – stresses in shafts – design for static loads – reversed bending and steady torsion – design for
strength and deflection – design for fatigue loading – critical speed of shafts, Stresses in couplings, Design of
couplings, Design of keyed and splined connections.
References
1. Shigley,J.E., Mechanical Engineering Design, 1st Metric ed., McGraw-Hill, 1986.
2. Shigley,J.E. and MischkeC.R., Mechanical Engineering Design, 6th ed., Tata McGraw-Hill, 2003.
3. Siegel,M.J., Maleev, V.L. and Hartman,J.B., Mechanical Design of Machines, 4th ed., International
Textbook Company, 1965.
4. Phelan,R.M., Fundamentals of Mechanical Design, Tata McGraw-Hill,1967.
5. Doughtie, V.L. and Vallance,A.V., Design of Machine elements, McGraw-Hill, 1964.
6. Juvinall, R.C. and Marshek,K.M., Fundamentals of Machine Component design, 3rd ed., John Wiley &
Sons, 2000.
7. Norton, R.L.,Machine Design, 2nd ed., Pearson Education, 2000.
Data Handbooks (allowed for reference during examinations also)
1. Narayana Iyengar, B.R. and Lingaigh, K.,Machine Design Data Handbook, Vol. I & II
2. P.S.G. Tech., Machine Design Data Hand Book.

Course Outcomes

CO1: To introduce general steps in design process and to familiarize mechanical design of components
subjected to static, fatigue and imposed loading.
CO2: To familiarize the design principles for threaded fasteners, bolted joints and riveted joints.
CO3: To familiarize analysis and design of welded connections and springs, for static and fatigue loading.
CO4: To familiarize analysis and design of shafts subjected to static and fatigue loads.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME4002 THERMAL ENGINEERING –II
L T P C
Prerequisite: ME2014 Thermodynamics 3 0 0 3

Total hours: 42 Hrs

Module 1 (12 hours)

Properties of steam – use of steam tables and Mollier chart – Separating and Throttling Calorimeter –properties
of mixtures of steam and atmospheric air, Psychrometric chart, Solution of problems on evaporative cooling
towers and wet cooling towers, Vapour and combined power cycle –Carnot vapour cycle – Ideal Rankine cycle
– deviations in an actual Rankine cycle – methods to increase the efficiency of the Rankine cycle – Reheat and
Regenerative cycles, Open and closed feedwater heaters – deaerator – co-generation – combined gas power
cycles.

Module 2 (10 hours)

Steam generators – fire tube–Lancashire, Locomotive and Nestler boilers, Water-tube – Babcock and Wilcox
and Bent-tube boilers,Mountings and accessories – schematic diagram of a modern steam generator –
combustion equipment – over feed and under feed stokers – travelling-grate and spreader stokers – pulverized
coal burners – cyclone furnace – fluidized-bed combustion, Steam nozzles – condition for maximum discharge
– design for throat and exit areas – effect of friction – supersaturated flow.

Module 3 (10 hours)

Steam turbines – classification – impulse and reaction turbine–velocity diagrams – efficiencies – end thrust –
blade height – turbine performance and governing, Condensers – purpose of a condenser in a steam power
plant – surface and mixing condensers, Different types of modern wet and dry cooling towers.

Module 4 (10hours)
Power Plant Economics – load curve and load duration curve – load, Diversity, Capacity and use factors –
selection of size and number of units – scheduling of operation – depreciation and replacement – environmental
aspects of thermal power systems, Dust collectors.

References

1. Y.A, Cengel, and M.A, Boles, Thermodynamics - An engineering approach, 4th ed., Tata McGraw Hill,
New Delhi, 2005.
2. M.M, El-Wakil,Power Plant Engineering, 1st ed., McGraw Hill, New York, 1985.
3. W.A., Vopat, and B.G.A., Skrotzki, Power Station Engineering and Econom., Tata McGraw Hill, New
Delhi, 1999.
4. Husain, and Zoeb, Steam turbines, Tata McGraw Hill, 1984.

Course Outcomes

CO1: To understand the significance of thermodynamic cycles w.r.t. steam power plant.
CO2:.To understand the co-generation plant.
CO3: To understand working of component of power plant.
CO4: To understand working of pollution control methods.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME4101 OPERATIONS RESEARCH

L T P C
Prerequisite: Nil
3 0 0 3
Total Hours: 42
Module 1 (12 hours)
An overview of operations research modelling approach, Basic linear algebra – matrices and systems of linear
equations – linear dependence and linear independence, Mathematical formulation of linear programming
problems, Graphical solution, Theory of simplex method, The simplex algorithm, Artificial starting solution –
M-method - two phase method, Alternative optimal solutions, Unboundedness, Degeneracy.
Module 2 (9 hours)
Duality in linear programming – Primal-dual relationships – Economic interpretation of duality, Transportation
problems – formulation and solution, Assignment problems – formulation and solution.
Module 3 (9 hours)
Game Theory – two-person zero-sum games – saddle points, Games with mixed strategies – graphical solutions
procedure – solving by linear programming.

Module 4 (12 hours)

Dynamic programming – characterization – Bellman’s principle of optimality – problems with a finite number
of concentric decisions, Queuing theory – generalized Poisson queuing model – steady state solution of single
server models for infinite queue size and finite queue size.
References
1. Taha, H.A., Operations Research: An Introduction, 8th ed., Pearson Education, Inc., 2008.
2. Hillier, F. S., and Lieberman, G. J., Introduction to Operations Research, 8th Ed., Tata McGraw Hill,
2005.
3. Ravindran A., Philips, D., and Solberg, J. J., Operations Research: Principles and Practice, 2nd ed.,
John Wiley & Sons Inc., 1989.
4. Hadley, G., Linear Programming, Addison Wesley Narosa, Narosa Publishing House, 1987.

Course Outcomes

CO1: To solve problems in optimization techniques.

CO2: To develop mathematical skills to approach a real life industrial problems.
CO3: To inculcate ideas to solve problems on transportation and queuing theory.
CO4: To import case studies problems to solve future problems.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME4091 HEAT ENGINES LABORATORY

Prerequisite: Nil L T P C
0 0 3 2
Total Hours: 42
Study of spark ignition (SI) and compression ignition (CI) engine systems - fuel system - lubrication system -
cooling system - starting system - ignition system - governing system - power transmission system - types of
carburetors - fuel injectors - multi point fuel injection (MPFI) system - common rail direct injection (CRDI)
system - gasoline direct injection (GDI) system, Study of different types of boilers and its components, Study of
fuel properties measuring systems - bomb calorimeter - gas calorimeter - red-wood viscometer - flash and fire
apparatus, Study of dynamometers, Constant speed performance characteristics of SI engine, Morse test at
constant throttle and at constant load, Constant speed performance characteristics of SI engine, Constant speed
performance characteristics of MPFI engine, Performance characteristics of constant speed CI engine, Constant
speed performance characteristics of single cylinder CI engine, Determination of frictional horse power (FHP)
by retardation test, Constant speed performance characteristics of reciprocating compressor, Variable speed
performance characteristics of SI engine (with carburetor and MPFI system), Performance characteristics of CI
variable speed engine, Determination of viscosity - flash and fire point - calorific value of the given fuel or oil,
Performance characteristics of centrifugal blower and rotary type positive displacement compressor by suitable
test, Performance characteristics with cooling water temperature (cooling curve experiment) by suitable test,
Valve timing diagrams of single and multi cylinder engines.

Course Outcomes

CO1: Familiarize the students to automobile component.

CO2: Performance study of various types of engines.
CO3: Hands on experience on engines and blowers.
CO4: Motivate students for innovation in automobile field.

Evaluation Weightage (%)

Component
Laboratory 60
Work
End Semester 40
Examination
 ME4191 CAD/CAM LABORATORY

Prerequisite: Nil L T P C
0 0 3 1
Total Hours: 42

Introduction to Computer Graphics – Viewing transformations, Curves and Surfaces generation – Familiarity
with Boolean operations – Sweep, Revolve, Loft, Extrude, Filleting, Chamfer, Splines etc. Windowing, View
Point, Clipping, Scaling and Rotation Transformations. Usage of commercial solid modelling packages like
Pro-E, CATIA, etc. Introduction to FEM-Mesh generation, Linear and Non Linear analysis-Static Dynamic
analysis, Post Processing, Exercises on Heat Conduction, fluid flow and Elasticity. Usage of commercial FEM
packages like ANSYS, ABAQUS etc. Synthesis and Design of Mechanisms - Animations, Exercises on various
mechanisms like four bar linkages and its variations, cam and follower, Two and Four Stroke engines, Design
for manufacturability - use of commercial software packages, Exercises in Process Control using PLC-PID
control strategy, CNC Part Programming fundamentals - Manual Part Programming and Computer Aided Part
Programming. Exercises on CNC Lathe and Machining Center/Milling machines, Rapid Prototyping, Hands on
training on industrial robots-manual and programmed path planning, Demonstration of the capability of
Coordinate Measuring Machine using sample component e.g.: Engine Block – Concepts of Reverse
Engineering and Rapid Prototyping.

References
1. Rogers, D.F., and Adams, J.A., Mathematical Elements for Computer Graphics, 2nd ed., Tata McGraw Hill,
2009.
2. Rogers, D.F., Procedural Elements for computer Graphics,2nd ed., Tata McGraw Hill, 1997.
3. Cook R.D., Malkus, D.S., Plesha,M.E., and Witt, R.J., Concepts and Applications of Finite Element
Analysis, 4th ed., John Wiley & Sons, 2001.
4. Koren, Y., Computer Control of Manufacturing Systems, McGraw Hill Book Company, 1986.
5. Rao, P.N., Tewari, N.K., and Kundra, T.K., Numerical Control & Computer Aided Manufacturing, Tata
McGraw Hill.
6. Ramamurthy, V., Computer Aided Mechanical Design and Analysis, 4th ed., Tata McGraw Hill, 2000.
7. Fu, K.S., Gonzalez, R.C., and Lee, C.S.G., Robotics, Control, Sensing, Vision and Intelligence, 1st ed.,
McGraw-Hill Book Company, 1987.
8. Koren, Y., Robotics for Engineers, Tata McGraw Hill, 1985.
9. Bosch, J.A., Coordinate measuring Machines &Systems, Marcel Decker Inc., New York.

Course Outcomes

CO1:To familiarize with various CAD/CAM packages used in the industry.

CO2:To enable students to do geometric modeling.
CO3:To enable students to do FEM and CFD analysis.
CO4:To enable students to take up jobs in product design and related areas.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME4098 PROJECT
Prerequisite: Nil
L T P C
Total Hours: 42
0 0 3 3

Students are required to take up a project (generally in groups) in any topic related to Mechanical Engineering
under the guidance of a faculty member. The project work commenced in VII Semester (normally 5
hours/week) shall be continued in VIII Semester too. At the end of the VII semester, an interim report
describing the details of the project work has to be submitted to the Department, usually in a prescribed format.
Presentation of this part of the work is to be done before an evaluation committee.
 SEMESTER 8

ME4011 MACHINE DESIGN – II

Prerequisite: ME2002 Elements of Solid Mechanics

L T P C
Total Hours: 42 3 0 0 3
Module 1 (12 hours)
Design of clutches, brakes, belts and chain drives – friction clutches and brakes – uniform pressure and uniform
wear assumptions – design of disc and cone types of clutches and brakes – design of external contracting and
internal expanding elements – band type clutches and brakes – belt and chain drives of common types – design
of flat and V-belt drives – selection of roller chains.
Module 2 (12 hours)
Design of gears – spur, helical, bevel and worm gears – tooth loads – gear materials – design stresses – basic
tooth stresses – stress concentration – service factor – velocity factor – bending strength of gear teeth –
Buckingham’s equation for dynamic load – surface strength and durability – heat dissipation – design for
strength and wear.
Module 3 (11 hours)
Lubrication and journal bearing design – types of lubrication and lubricants – viscosity – journal bearing with
perfect lubrication – hydrodynamic theory of lubrication – design considerations – heat balance – journal
bearing design, Rolling Contact Bearings – bearing types – bearing life – static and dynamic capacity –
selection of bearings with axial and radial loads – lubrication – seals – shaft, housing and mounting details.
Module 4 (7 hours)
Product design for manufacturing – general design recommendations for rolled sections – forgings – screw
machine products – turned parts – machined round holes – parts produced on milling machine – welded parts
and castings –modification of design for manufacturing easiness for typical products.
References
1. Shigley,J.E., Mechanical Engineering Design, 1st Metric ed., McGraw-Hill, 1986.
2. Shigley,J.E. and MischkeC.R., Mechanical Engineering Design, 6th ed., Tata McGraw-Hill, 2003.
3. Siegel,M.J., Maleev, V.L. and Hartman,J.B., Mechanical Design of Machines, 4th ed., International
Textbook Company, 1965.
4. Phelan,R.M., Fundamentals of Mechanical Design, Tata McGraw-Hill, 1967.
5. Doughtie, V.L. and Vallance,A.V., Design of Machine elements, McGraw-Hill, 1964.
6. Juvinall, R.C. and Marshek,K.M., Fundamentals of Machine Component design, 3rd ed., John Wiley &
Sons, 2000.
7. Norton, R.L.,Machine Design, 2nd ed., Pearson Education, 2000.
8. James G. Bralla, Handbook of Product Design for Manufacture, McGraw Hill
Data Handbooks (allowed for reference during examinations also)
1. Narayana Iyengar, B.R. and Lingaigh, K.,Machine Design Data Handbook, Vol. I & II
2. P.S.G. Tech., Machine Design Data Hand Book.

Course Outcomes

CO1:To familiarize analysis and design of clutches, brakes, drives and chain drives.
CO2:To familiarize analysis and design of spur, helical, bevel and worm gears subjected to static, dynamic
and wear loads.
CO3:To familiarize analysis and design of journal bearings and rolling contact bearings.
CO4:To introduce and familiarize concepts of product design for manufacturability.
Evaluation Weightage (%)
Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 MS4004 INDUSTRIAL ECONOMICS

Prerequisite: Nil L T P C
3 0 0 3
Total Hours: 42 Hrs

Module 1(11 hours)

General Foundations of Economics; Nature of the firm; Forms of organizations-Objectives of firms-Demand
analysis and estimation-Individual, Market and Firm demand, Determinants of demand, Elasticity measures and
business decision making, Demand Forecasting-Theory of the firm-Production functions in the short and long
run-Cost concepts- Short run and long run costs- economies and diseconomies of scale

Module 2 (9 hours)
Product Markets-Market Structure-Competitive market-Imperfect competition (Monopoly, Monopolistic
competition and Oligopoly) and barriers to entry-Pricing in different markets-Differential Pricing-Supply,
Demand and Government Policies-Game Theory-Prisoner’s Dilemma

Module 3 (11 hours)

Macro Economic Aggregates-Gross Domestic Product; Economic Indicators; Models of measuring national
income; Inflation ; Fiscal and Monetary Policies ; Monetary system; Money Market, Capital market; Indian
stock market; Development Banks; Changing role of Reserve Bank of India

Module 4 (11 hours)

International trade - Foreign exchange market- Balance of Payments (BOP) and Trade-Effects of
disequilibrium in BOP in business- Trade regulation- Tariff versus quotas- International Trade and development
and role of international institutions (World Bank, IMF and WTO) in economic development.

References
1. Bo Soderston,International Economics,
2. Gupta, S.B Monetary Economics,. (1994). S. Chand & Co., New Delhi.
3. Gregory.N.Mankiw,Principles of Micro Economics, Cengage Publications,2007
4. Gregory.N.Mankiw ,Principles of Macro Economics, Cengage Publications,2007
5. Indian Economy – Its Development Experience, Misra, S.K. and V.K. Puri (2001)Himalaya
Publishing House, Mumbai,2009.
6. Microeconomics, R.S. Pindyck, D.L Rubinfield and P.L. Mehta ,Pearson Education, 2005. Advanced
Economic Theory, Micro Economics H.L. Ahuja,Chand Publications,2004.
7. Economics,Samuelson, P.A.;& W.D. Nordhaus ,Tata McGraw Hill,18 Ed.,2005.
8. Public Finance , B.P.Tyagi,Jai PrakashNath & Co.,1997.

PN : Supplementary materials would be suggested / supplied for select topics on Indian economy
Course Outcomes

CO1:To evaluate the economics of the management, operation, and growth and profitability of engineering
firms and analyze operations of markets under varying competitive conditions.

CO2:The course equips a student to carry out and evaluate benefit/cost, life cycle and breakeven analyses on
one or more economic alternatives.

CO3: To analyze cost/revenue data and carry out make economic analyses in the decision making process to
justify or reject alternatives/projects on an economic basis.

CO4:Produce a constructive assessment of a social problem by drawing the importance of environmental

responsibility and demonstrate knowledge of global factors influencing business and ethical issues.

CO5:Helps to use models to describe economic phenomena; analyze and make predictions about the impact of
government intervention and changing market conditions on consumer and producer behavior and well-being.

Evaluation Weightage (%)

Component
Test 1 20
Test 2 20
Assignments 10
End Semester 50
Examination
 ME4097 SEMINAR

L T P C
0 0 3 1
Prerequisite: Nil
Total Hours: 42
Search technical literature in the form of peer reviewed journals and conference proceedings and identify a
current research topic relevant to Mechanical Engineering – Comprehend the topic and prepare a technical
report on the topic of presentation in the specified format– Prepare presentation aids and deliver a technical
presentation to the class – Appropriate weights will be given for communications skills (both verbal and
written) as well as for capacity to impress the audience and ability to handle question and answer session.

Course Outcomes

CO1: To train the students to search technical literature.

CO2: To identify a current and relevant research topic.
CO3: To understand and deliver a presentation.
CO4: To write a technical report.
 ME4098 & ME4099 PROJECT

Prerequisite: ME4098 Project

L T P C
Total Hours: 70
0 0 5 5

The project work commenced in VII Semester shall be continued in VIII Semester, normally 5 hours/week. At
the end of the VIII semester, the final report/thesis describing the details of the entire project work has to be
submitted to the Department, usually in a prescribed format. Presentation of the entire work is to be done
before an evaluation committee and a successful oral defense of the thesis before the committee is required.

Course Outcomes

CO1: Ability to work on practical problems by applying the knowledge gained from courses in Mechnical
Engineering curriculum.
CO2: Practical experience gained through the in-depth study of a challenging problem in Mechanical
Engineering field.
CO3: Acquire innovative problem solving skills and conceptualization of creative ideas.
CO4: Improve the team working and communication skills for a successful professional career .
 ELECTIVES

ME3021 INTRODUCTION TO FINITE ELEMENT METHODS

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1 (10 hours)
Introduction – various numerical methods – concepts of variational calculus – variational methods of
approximation, Ritz method, Weighted residual methods – Galerkin method – subdomain method – least square
method – collocation method, Problems.
Module 2 (10 hours)
Finite element analysis of one-dimensional problems – procedure – one-dimensional elements and interpolation
functions – analysis of one-dimensional second and fourth order equations – natural co-ordinates– interpolation
functions – computer implementation.
Module 3 (12 hours)
Finite element analysis of two-dimensional problems – two-dimensional elements and interpolation functions –
second order equations involving a scalar valued function – comments on mesh generation and composition of
boundary conditions – analysis of plane elasticity and incompressible fluid flow problems – time dependent
problems (transient heat transfer) – iso-parametric elements and numerical integration.
Module 4 (10 hours)
Dynamic Analysis – Hamilton’s Principle – Eigen value problems – non linear problems – three-dimensional
elements and interpolation functions – formulation of three-dimensional problems – two and three-dimensional
Navier Stoke’s equations – three-dimensional heat transfer equations.
References
1. Reddy, J.N., An Introduction to the Finite Element Method, 3rd ed.,Tata McGraw-Hill, 2005.
2. Reddy, J.N., Applied Functional Analysis and Variational Methods in Engineering, International Edition,
McGraw-Hill, 1987.
3. Huebner, K. H., The Finite Element Method for Engineers, John Wiley& Sons.
4. Zienkiewicz, O.C., The Finite Element Method, Tata McGraw-Hill Edition.
5. Zienkiewicz, O.C., and Morgan, K., Finite Elements and Approximation, John Wiley & Sons, 1983.
6. Cook, R.D., Malkus, D.S., Plesha, M.E., and Witt, R.J., Concepts and Applications of Finite Element
Analysis, 4th ed., John Wiley & Sons, 2004.
 ME3022 EXPERIMENTAL STRESS ANALYSIS

Prerequisite: ME2002 Elements of Solid Mechanics or Equivalent

L T P C
Total Hours: 42 3 0 0 3
Module 1 (9 hours)
Analysis of stress at a point and strain at a point, Stress-strain relations, Principal stresses and principal strains,
Prediction of failures,Basic equations in elasticity theory, Formulation of problems, Field equations, Plane
stress and plane strain problems, Solution of problems using Airy’s stress function.
Module 2 (12 hours)
Strain measurements, Strain and its relation to experimental determinations, Types of strain gauges –
mechanical strain gauges – optical strain gauges - inductance strain gauges, Electrical resistance strain gauges -
strain sensitivity in metallic alloys - gauge construction-strain gauge adhesives and mounting methods - gauge
sensitivities and gauge factor – performance characteristics of foil strain gauges - temperature compensation,
Strain gauge circuits - potentiometer - Wheatstone bridge circuits.
Strain rosettes- rectangular and delta rosette.
Module 3 (12 hours)
Photo elasticity - basics of optics  double refraction - stress optic law - stress and birefringence, Two
dimensional photoelasticity - plane polariscope - circular polariscope - isoclinics - isochromatics - effects of
stressed model in a plane polariscope and circular polariscope – dark field and light field arrangements,
Compensation techniques ,Photoelastic materials, Calibration methods, Separation methods, Scaling model to
prototype stresses.
Module 4 (9 hours)
Theory of brittle coating method - coating stresses, Failure theories - brittle coating patterns - crack detection,
Ceramic based brittle coatings, Resin based brittle coatings, Test procedures for brittle coating analyses -
analysis of brittle coating data.
References
1. James. W. Dally, and William E. Riley, Experimental Stress Analysis, McGraw Hill, Third Edn., 1991.
2. R.G. Budynas, Advanced Strength and Applied Stress Analysis, McGraw Hill, Second Edn., 1999.
3. L.S. Sreenath, M.R. Raghavan, K. Lingaiah, G. Garghesha, B. Pant, and K. Ramachandra,
Experimental Stress Analysis, Tata Mc Graw Hill.
4. Timoshenko and Goodier, Theory of elasticity,McGraw Hill, New York, Third Edn., 1970.
 ME3023 THEORY OF PLASTICITY

Prerequisite: ME2012 Applied Mechanics of Solids

L T P C
Total Hours: 42
3 0 0 3
Module 1 (10hours)
Review of the theory of stress and Strain – transformation laws –principal stress and strain –Mohr’s circle,
Stress strain relations, Material properties, Introduction to the theory of plasticity – behaviour of metals under
uni-axial tension and compression — true stress-true strain relations — effect of work hardening, Bollarding
and Barrelling, Empirical stress-strain relations for work hardening materials.
Module 2 (10 hours)
Yield criterion – stress space representation of yield criterion – representation of Tresca and von-Mises criterion
– yield surface for work hardening materials, Stress strain relations in the plastic range — Prandtl -Reuss,
Levy-Mises and St. Venant’s stress-strain relations, Plastic potential, Principle of maximum work dissipation.
Module 3 (12 hours)
Elastic-Plastic analysis – pure bending of a beam – torsion of circular bar – thick spherical shell under internal
pressure – thick cylindrical shell under internal pressure – rotating cylinders – rotating disks, Plane strain
problems – simple slip line fields, Bound theorems and their applications
Module 4 (10 hours)
Application of the theory of plasticity to metal forming operations – plasticity analysis of extrusion and drawing
of wires and strips – analysis of tube drawing with mandrels – analysis of rolling – analysis of forging,Load
calculations for the operations.
References
1. Chakrabarty, J., Theory of Plasticity, Van-Nostrand Reinhold Co., London, 1975.
2. Johnson, W., and Meller, P.B., Engineering Plasticity,Mc-Graw Hill Book Co., New York, 1987.
3. Hoffman, O. and Sachs, G., Introduction to the theory of Plasticity for Engineers, Mcgraw Hill Book
Co., New York, 1953.
 ME3024 CONTROL SYSTEMS ENGINEERING

Prerequisite: Nil L T P C
Total Hours: 42 3 1 0 3
Module 1 (12 hrs)
Introduction to control system engineering, History, Representation of feedback control system by block
diagrams, Physical systems and their mathematical models, Representation of linear time invariant systems,
Order of the system, Classical method, Transfer function approach, Block diagram reduction, State space
representation, Mathematical models of mechanical, electrical, hydraulic and pneumatic elements and systems,
Conversion of state Space to transfer function and transfer function to state space, Transformation of
mathematical model using MATLAB.
Module 2 (12 hrs)
Transient response analysis, Solution of first order, Second order and Higher order systems, Solution by
Laplace transform, Solution of states space equation, Performance parameters of first order and second order
systems, Stability of systems, Routh-Hurwitz criterion, Steady state error, Error constants, Improving time
response and steady state error, Root locus techniques, Application of MATLAB in transient response.
Module 3 (8 hrs)
Frequency response of systems, Plotting the frequency response, Rectangular plots, Polar plots, Bode plots and
Nichols chart, Stability analysis, Nyquist plots and Nyquist criterion, Gain margin, Phase margin, Application
of MATLAB in frequency response.
Module 4 (10 hrs)
Design of control systems, The design philosophy, Design of Lead, Lag, Lead- Lag, Proportional, Integral,
derivative and PID controllers using Root locus and Bode plot, Tuning of controllers and PID controller gain
tuning techniques, Design of controllers via state space, Controllability and observability, Applications of
MATLAB in design of controllers.
References
1. Ogata, K., Modern Control Engineering, 4th ed., Prentice-Hall of India, 2002.
2. I.J. Nagrath, I.J., and Gopal, M., Control Systems Engineering, 5th ed., New Age International
Publishers, 2007.
3. Ogata, K., System Dynamics, 4th ed., Pearson Education Inc., 2004.
4. Kuo, B.C., Automatic Control Systems, 7th ed., Prentice-Hall of India, 1995.
5. Chen ,C.T., Linear System Theory and Design, 3rd ed.,OxfordUniversity Press, 1999.
6. Franklin, G.F., Powell,J.D., and Naeini,A.E.,Feedback Control of Dynamic Systems, 4th ed., Prentice
Hall, 2002.
7. Dorf R.C., and Bishop,R.H.,Modern Control Systems, 11th ed., Pearson Education, 2008.
8. Azzo, J.J.D., and Houpis, C.H.,Linear Control System Analysis and Design, 4th ed., McGraw Gill
Publishers, 1995.
 ME3025 NONLINEAR DYNAMICS AND CHAOS

Prerequisite: ZZ1001 Engineering Mechanics

L T P C
Total Hours: 42
3 0 0 3
Module 1 (10hours)
Introduction to dynamical systems, Discrete and continuous time systems, Autonomous and non-autonomous
systems, Discrete time systems – one-dimensional map – fixed points of maps and their stability, Bifurcation of
maps, Continuous time systems –phase space and flows –attracting sets, Concepts of stability.

Module 2 (10hours)
Equilibrium solutions, Fixed points and stability of continuous time systems, Classification and stability of
equilibrium solutions, Periodic solutions –Periodic solutions of continuous time dynamical systems,
Autonomous and non-autonomous systems, Limit cycle, Poincarésection, Bifurcation –local and global
bifurcation of continuous systems –static and dynamic bifurcations – Hopf bifurcations, Quasiperiodic
solutions, Circle map.

Module 3 (10 hours)

Dynamics of discrete time systems, Logistic equation –bifurcation diagram of one-dimensional maps –chaotic
solutions of maps, Henon map, Continuous systems – Duffing's equation – Rosslerequations- period doubling
and Intermittency mechanisms, Tools to identify and analyze motions –time history –state-space and pseudo
state space- Fourier spectra – Poincare' sections and maps, Lyapunov exponents.

Module 4 (12 hours)

Fractals and dynamical systems, Examples of fractals – Koch curve – Cantor set etc., Fractal dimension –
measures of fractal dimension, Computational methods – shooting method, harmonic balance method,
Determination of Lyapunov exponents and fractal dimensions, Applications of nonlinear dynamics.

References

1. Strogatz,S.H., Nonlinear Dynamics and Chaos, Westview Press, 1994.

2. Nayfeh, A.H., and Balachandran,B., Applied Nonlinear Dynamics, John Wiley & Sons, 1995.
3. Thomson, J.M.T., and. Stewart,H.B, Nonlinear Dynamics and Chaos, John Wiley & Sons, 1986.
4. Moon,F.C., Chaotic and Fractal Dynamics, John Wiley & Sons, 1987.
5. Baker, G.L., and Gollub,J.P., Chaotic Dynamics, 2nd ed., CambridgeUniversity Press, 1996.
6. Peitgens, Jurgens, and Saupe, Chaos and Fractals, Springer Verlag, 1992.
7. Scheinerman,E.R., Invitation to Dynamical Systems, Prentice hall, New Jersey, 1996.
8. Drazin,P.G., Nonlinear Systems, CambridgeUniversity Press, 1992.
9. Devaney,R.L., An Introduction to Chaotic Dynamical Systems, 2nd ed., Addison-Wesley, 1989.
10. Jordan, D.W., Smith,P, Nonlinear ordinary differential equations, 4thed.,Oxford University Press,2007.
 ME3026 ENGINEERING FRACTURE MECHANICS

Prerequisite 1: ME2002 Elements of Solid Mechanics

L T P C
Prerequisite 2: ME2012Applied Mechanics of Solids/
3 0 0 3
ME2015 Theory of Elasticity and Plasticity
Total Hours: 42
Module 1 (10 hours)
Introduction – significance of fracture mechanics, Stress concentration factor, Griffith energy balance approach,
Irwin’s modification to the Griffith theory, Stress intensity approach, Crack tip plasticity, Fracture toughness,
Subcritical crack growth,Influence of material behaviour, Problems in I, II &III modes, Mixed mode problems,
Linear elastic fracture mechanics (LEFM) – elastic stress field approach – mode I elastic stress field equations –
expressions for stresses and strains in the crack tip region, Finite specimen width, Superposition of stress
intensity factors (SIF),SIF solutions for well known problems.
Module 2 (10hours)
Energy balance approach – Griffith energy balance approach – relations for practical use, Determination of SIF
from compliance, Slow stable crack growth and R-curve concept,Description of crack resistance, LEFM Testing
– Plane strain and plane stress fracture toughness testing, Determination of R-curves, Effects of yield strength
and specimen thickness on fracture toughness, Practical use of fracture toughness and R-curve data.
Module 3 (10hours)
Crack Tip Plasticity – Irwin plastic zone size – Dugdale approach – shape of plastic zone – state of stress in the
crack tip region, Elastic plastic fracture mechanics (EPFM) – development of EPFM, J-integral, Crack opening
displacement (COD) approach, COD design curve, Relation between J and COD, Standard J Ic test and COD
test.
Module 4 (12 hours)
Fatigue crack growth – description of fatigue crack growth using stress intensity factor, Effects of stress ratio
and crack tip plasticity, Crack closure, Paris Law, Prediction of fatigue crack growth under constant amplitude
and variable amplitude loading, Fatigue crack growth from notches – short crack problem, Practical problems –
through cracks emanating from holes – corner cracks at holes – cracks approaching holes – fracture toughness
of weldments – service failure analysis – applications in pressure vessels, pipelines and stiffened sheet
structures.
References
1. Ewalds, H.L. and Wanhill, R.J.H., Fracture Mechanics,1st ed., Edward Arnold Edition, 1993.
2. Broek, D.,Elementary Engineering Fracture Mechanics,4th ed., Sijthoff & Noordhoff International
Publishers, 1991.
3. Kåre Hellan,Introduction to Fracture Mechanics, McGraw-Hill Book Company, 1983.
4. Prashant Kumar,Elements of Fracture Mechanics, Wheeler Publishing, 1999.
 ME3027 FLUID POWER CONTROLS

Prerequisite: ME2001 Fluid Mechanics L T P C

Total Hours: 42 3 0 0 3

Module 1 (10 Hours)

Introduction to oil hydraulics and pneumatics, their advantages and limitations, ISO symbolsand standards in
Oil Hydraulics and pneumatics, Recent developments, applications, Basictypes and constructions of Hydraulic
pumps and motors, Ideal pump and motor analysis, Practical pump and motor analysis, Performance curves and
parameters.
Module 2 (11 Hours)
Hydraulic Actuators, Hydraulic control elements – direction, pressure and flow control valves. Valve
configurations, General valve analysis, valve lap, flow forces and lateral forces on spool valves, Series
andparallel pressure compensation flow control valves, Flapper valve Analysis and Design, Analysisof valve
controlled and pump controlled motor, Electro-hydraulic servo valves-specifications,selection and use of servo
valves.
Module 3 (11 Hours)
Electro hydraulic servomechanisms – Electro hydraulic position control servos and velocitycontrol servos,
Nonlinearities in control systems (backlash, hysteresis, dead band and frictionnonlinearities). Basic
configurations of hydraulic power supplies – Bypass Regulated and StrokeRegulated Hydraulic Power Supplies,
Heat generation and dissipation in hydraulic systems: Design and analysis of typical hydraulic circuits, Use of
Displacement – Time and Travels-Step diagrams: Synchronization circuits and accumulator sizing. Meter-in,
Meter-out and Bleed-off
circuits: Fail Safe and Counter balancing circuits.
Module 4 (10 Hours)
Components of pneumatic systems: Direction, flow and pressure control valves in pneumaticsystems,
Development of single and multiple actuator circuits, Valves for logic functions: Time delay valve, Exhaust and
supply air throttling, Examples of typical circuits using Displacement – Time and Travel-Step diagrams, Will-
dependent control, Travel-dependent control and Timedependentcontrol, combined control, Program Control,
Electro-pneumatic control and air hydraulic control, Applications in Assembly, Feeding, Metalworking,
materials handling andplastics working.
References
1. Joji,P., Pnumatic controls, Wiley India Pvt. Ltd., 2008.
2. Anthony Esposito., Fluid Power with applications, Pearson Education.
3. Ernst, W., Oil Hydraulic Power and its Industrial Applications, New York, McGraw Hill.
4. Lewis, E. E., and H. Stern, Design of Hydraulic Control Systems, New York,McGraw Hill.
5. Morse, A. C., Electro hydraulic Servomechanism, New York, McGraw Hill.
6. Pippenger, J.J., and R.M. Koff, Fluid Power Control systems, New York, McGraw Hill.
7. Fitch, Jr., E.C., Fluid Power Control Systems, New York, McGraw Hill.
8. Khaimovitch., Hydraulic and Pneumatic Control of Machine Tools.
9. John Watton., Fluid Power Systems: modeling, simulation and microcomputer control, Prentice Hall Int.
10. Herbert E. Merritt., Hydraulic control systems, John Wilely and Sons Inc.
11. Thoma, Jean U., Hydrostatic Power Transmission, Trade and Technical Press, Surrey, England.
12. Ian Mencal., Hydraulic operation and control of Machine tools, Ronald Press.
13. Sterwart., Hydraulic and Pneumatic power for production, Industrial Press.
14. Hasebrink J.P., and Kobler R., Fundamentals of Pnuematics/electropeumatics, FESTODidactic publication.
15. Werner Deppert and Kurt Stoll., Pneumatic Control-An introduction to the principles, Vogel – Verlag.
16. Blaine W. Andersen., The analysis and Design of Pneumatic Systems, John Wiley and Sons, Inc.
17.Blackburn, J.F., G. Reethof, and J.L. Shearer, Fluid Power Control, New York, Technology Press of M. I. T.
 ME3028 ADVANCED THERMODYNAMICS

Prerequisite: ME2014 Thermodynamics

L T P C
Total Hours: 42 3 1 0 3

Module 1 (10 hours)

General principles of classical thermodynamics  postulational approach  basic postulates  conditions of
equilibrium  fundamental equations  equations of state, Euler equation, Gibbs-Duhem equation, Multi-
component simple ideal gases.

Module 2 (10 hours)

Reversible processes  maximum work theorem  alternate formulation  energy minimum principle, Legendre
transformations, Extremum principles in the Legendre transformed representation, Thermodynamic potentials
and Massieu functions.

Module 3 (10 hours)

Maxwell relations and Jacobian methods, Procedure to reduction of derivatives, applications, Stability criteria
of thermodynamic systems, First-order phase transition, single component and multi-component systems, Gibbs
phase rule  phase diagram for binary systems.

Module 4 (12 hours)

Critical phenomena, Liquid and solid Helium, Nernst postulate, Introduction to irreversible thermodynamics 
linearised relation  Onsager’s reciprocity theorems, Special topics on advanced thermodynamics.

References

1. Callen, H.B., Thermodynamics and an Introduction to Thermostatics, Second Edition, John Wiley &
Sons, 1985.
2. Rao, Y.V.C., Postulational and Statistical Thermodynamics, Allied Publishers, 1994.
3. Zemansky, M.W., Abbot, M.M. and Van Ness, H.C., Basic Engineering Thermodynamics, McGraw-
Hill, 1987
4. Saad, M.A.,Thermodynamics for Engineers, Prentice Hall of India, 1987.
5. Lee, J.F., Sears, F.W., Thermodynamics: An Introductory Text for Engineering Students, Addison
Wesley, 1964.
6. Wark Jr., K., Advanced Thermodynamics for Engineers, McGraw-Hill, 1995.
7. O’ Cornell, J. P. and Maile, J. M.,Thermodynamics – Fundamentals for Applications,
CambridgeUniversity Press, 2004.
8. Sonntag, R.E., Borgnakke, C and Van Wylen, G. J., Fundamentals of Thermodynamics, Sixth Edition,
John Wiley & Sons, 2004.
 ME3029 COMPUTATIONAL METHODS IN ENGINEERING

Prerequisite: Nil
L T P C
Total Hours: 42
3 0 0 3

Module 1 (8hours)
Basic consideration in numerical methods, Numerical error and accuracy –round-off error –truncation error –
accuracy of numerical results –Numerical stability, Iterative convergence –conditions of convergence –rate of
convergence –termination of iteration, Numerical parameters –step size –convergence criterion, Numerical
differentiation, –Taylor series approach – polynomial fitting approach.
Module 2 (12hours)
Numerical solution of linear algebraic equations, Direct methods – Gaussian elimination – tridiagonal matrix
algorithm –LU decomposition, Indirect methods –Jacobi iteration – Gauss-Seidel iteration, Under relaxation
and over relaxation, Root of equations, Search method for real roots, Bisection method, Regula falsi and secant
methods, Newton-Raphson method and modified Newton’s method .
Module 3 (10 hours)
Numerical curve fitting and interpolation, Exact fit and interpolation – exact fit with an n-th order polynomial –
uniformly spaced independent variable, Lagrange interpolation, Newton’s divided-difference interpolating
polynomial – general formulas – uniformly spaced data – extrapolation, Numerical interpolation with splines,
Method of least squares for a best fit –basic considerations – linear regression – best fit with a polynomial.
Module 4 (12hours)
Numerical integration –rectangular and trapezoidal rules –Simpson’s rules, Higher-accuracy methods –
Richardson extrapolation –Romberg integration –higher-order Newton-Cotes formulas , Integration with
segments of unequal width –unequally space data –adaptive quadrature –Gauss quadrature, Numerical solution
of ordinary differential equations, Initial value problems –Euler’s method – Heun’s method –Modified Euler’s
method –Runge-Kutta methods –predictor-corrector methods, Boundary value problems –shooting methods –
finite difference methods.

References
1. Jaluria, Y., Computer Methods for Engineering, Allyn and Bacon, Inc., 1988.
2. Chapra, S.C., and Canale, R.P., Numerical Methods for Engineers,4th ed, Tata McGraw-Hill, 2002.
3. Griffith, D.V., and Smith, I.M., Numerical Methods for Engineers:A Programming Approach, CRC
Press, 1991.
 ME3121 POWDER METALLURGY

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3

Module 1 (10 hours)

Versatility and benefits of Powder Metallurgy, PM Process, Powder production techniques-mechanical,
atomisation, chemical-reduction and carbonyl and electro-chemical processes: Ceramic powder production,
Powder properties and their characteristics, Sieve analysis, Microscopy, Sedimentation analysis: Specific
surface and other technological properties: Powder conditioning.
Module 2 (11 hours)
Compaction and shaping - Cold and Iso-static compaction, Die compaction, Pressing equipments and tooling:
Powder Injection Moulding, Extrusion and rolling. Hot compaction techniques, Hot Iso-static Pressing (HIP),
equipments, tooling and applications: Explosive compaction: Slip casting.
Module 3 (10 hours)
Sintering-stages, single component, material transport mechanisms: Model studies: Powder shrinkage
experiments: Sintering diagrams and sintering anomalies. Multi-component sintering-solid phase and liquid
phase, infiltration and reaction sintering: Sintering atmospheres and equipments.
Module 4 (11 hours)
Powder metallurgy products, Porous parts, Sintered carbides, Cermets, Electric and magnetic parts and ceramic
components, Sintered friction materials. P/M parts of the year, Research trends in Powder Metallurgy.
References
1. Thummler, F., and Oberacker, R., An introduction to Powder Metallurgy, The Institute of Materials, The
University Press, Cambridge Great Britain.
2. ASM Handbook, Powder Metal Technologies and Applications(ASM Handbook, Vol 7).
3. Leander, F., and West, W.G., Fundamentals of Powder Metallurgy,Metal Powder Industries Federation,
2002.
4. Upadhyaya, G.S., Powder Metallurgy Technology, 1st ed., Cambridge International Science Publishing Co,
2002.
5. Sinha, A.K., Powder Metallurgy, Dhanpat Rai Publications, 2003.
6. Angelo, P.C., and Subramanian, R., Powder Metallurgy, Prentice Hall of India, 2008.
 ME3122 INTRODUCTION TO MARKETING

Prerequisite: MA2001 Mathematics III: Probability and Statistics

Total Hours: 42 L T P C
3 0 0 3
Module 1(10 Hours)
Introduction to marketing, Evolution of marketing concept, Scope of marketing, Marketing management task,
Functions of marketing, Marketing mix, Developing marketing strategies, Marketing and customer value,
Corporate and division. Strategic planning in marketing, Business unit strategic planning, Contents of
marketing plan.

Module 2 (10 Hours)

Identifying market segments and targets, Levels of market segmentation, Base for segmenting consumer
markets, Base for segmenting business markets, Marketing Research--Marketing Research Process-Research
objectives, Research Plan development, Collecting information, Analysis.

Module 3 (10 Hours)

Analyzing consumer markets, Influencing consumer behavior, The buying decision process, Theories of
consumer decision making, Analyzing Competitive strategies business markets, Organizational buying,
Participating in the buying process, Stages in buying process, Managing business to business customer
relations, Institutional government markets.

Module 4 (12 Hours)

Product strategy, Product characterization and classification, Product and brand relationship, Packaging,
Challenges in new product development, Consumer adoption process, Product lifecycle marketing strategy,
Brand management, Developing pricing strategies and progress, Understanding prices, Setting the prices,
Adapting the prices, Initiating and responding to price changes.

References

1. Kotler, P.,Keller, K..L., Koshy, A., and Jha, M.,Marketing Management, 13th edition, Prentice Hall India
Ltd, New Delhi, 2009.
2. Ramaswamy V.S and Namkumari S., Marketing Management, Macmillan India Ltd, New Delhi, 1997.
3. Keegan, Global Marketing Management, Pearson Education India, New Delhi, 2002.
4. Saxena, Marketing Management, 2nd edition, Tata McGraw Hill , 2002.
ME3123 DESIGN AND ANALYSIS OF MANAGEMENT INFORMATION SYSTEMS

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1 (11 hours)
Concepts of data and information – Producing information from data – economies of information – analysis of
system – management and formal information system concepts, Building blocks in information systems –
system design forces – information development life cycle – information systems for strategic planning.

Module 2 (10 hours)

General steps in Information system design – systems investigation and requirements engineering – System
analysis and general system design – charting tools for system analysis and design.
Module 3 (11 hours)
Introduction to database management – classification of data items – Coding considerations – types of code
structures – Forms design. General File storage consideration – composition and classification of data files –
selection consideration for file media and file organization methods, concepts of data structures – data
association – sorting and searching techniques.
Module 4 (10 hours)
System implementation – Verification and Validation of Software system – Software metric and models,
introduction to capability maturity model – software testing approaches – training and post implementation
audit – Recent developments in information systems, Security features in global information systems.
References
th
1. Burch and Grudnitski, Information Systems – Theory and Practice, 5 ed., John Wiley & Sons, New
York, 1989.
2. Hawryszkiewycz, I.T., Introduction to Systems Analysis and Design, Prentice Hall of India, 1989.
th
3. Ian Sommerville, Software Engineering, 6 ed., Pearson Education Asia, 2001.
th
4. Lucas, Henry C., Analysis, Design, and Implementation of Information Systems, 4 ed., McGraw Hill,
New York, 1992.
5. O’ Brien, J.A., Management Information Systems, 4th ed., Tata McGraw Hill, 1999.
 ME3124 WORK DESIGN AND MEASUREMENT

Prerequisite: Nil
Total Hours: 42 hours L T P C
3 0 0 3
Module 1 (12 Hours)
Definition and scope of work design and measurement –work Design and methods study –scope of work
design – procedure for methods study – process analysis –processcharts –operationanalysis – cyclographs –
principles of motion economy, WorkMeasurement – objectives –timestudy equipment –establishmentand
maintenance of time standards, Allowances and performance rating, Conceptof rating in time study.
Module 2 (10 Hours)
Precision time measurement, Synthesis of standard data, Pre-determined fundamental motion time standards –
MTM, Workfactor System, Standard data, Work sampling – statisticaltechniques in work sampling –
confidence limits, WorkStudy in office –work simplification –measurement of performance, Formsdesign –
diagnosticand procedure charts.
Module 3 (10 Hours)
Ergonomics –natureof man-machine systems – characteristics – purpose,Operational functions and components
– types of systems, Information input and processing, Sources and pathways of stimuli, Human information
processing, Visual displays – quantitative and qualitative displays – visual codes, symbols and signs – general
guidelines in design of visual displays.
Module 4 (10 Hours)
Auditory and tactual displays – masking –typesof auditory displays – cutaneous senses , Tactual displays,
Speech communication – speech intelligibility – components of speech communication, Nature of human
activity and their effects, Bases of human motor activity –humancontrol of systems – input-output channels –
compatibility, Influence of display factors and control factors on system control.
References
1. Barnes, R. M,Motion and Time Study: Design and Measurement of Work, John Wiley& Sons, NY, 7thed.,
1980.
2. Mark S. Sanders and Earnest J. McCormick,Human Factors in Engineering and Design, 6th ed., McGraw-
Hill, 1987.
3. Marvine E., Mundel, D. Danner, and David L.Anner,Motion and Time Study, 6th ed., Prentice Hall of India,
1985.
4. Murrell K.F.H. and Schnauber, H,Ergonomics. Econ, Munich, 1986.
5. Gavriel Salvendy,Handbook of Human Factors & Ergonomics, Inter-science, 1997.
 ME3125 COST ANALYSIS AND CONTROL

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1(10Hours)
Nature of Management Accounting,Generally accepted Accounting Principles and Accounting Standards,
Accounting Cycle and Statements of Financial Information Understanding Corporate Financial Statements and
Reports.

Module 2 (10 Hours)

Cash Flow Statement, Financial Statements Analysis,Cost Concepts and Management Needs, Costing and
Control of Materials, Costing and Control of Labour ,Costing and Control of Factory (Manufacturing)
Overheads ,Costing and Control of Administrative, Selling and Distribution Overheads.

Module 3 (10 Hours)

Activity Based Costing System, Job-Order and Batch Costing, Process, Joint and By-Product Costing, Variable
Costing and Absorption (Full) Costing

Module 4 (12 Hours)

Volume-Cost-Profit Analysis, Budgeting and Profit Planning, Standard Costs and quality Costs, Cost Variance
Analysis, Revenue and Profit Variance Analysis, Responsibility Accounting, Short-Run Decision Analysis,
Capital Budgeting

References

1. Khan, M Y. and Jain, P K, Management Accounting: Text, Problems and Cases, 4/e, Tata McGraw-Hill,
2009.
2. Horngren, C.T., Datar, S.T., Foster, D., Rajan, M.V. and Ittner, C., Cost Accounting: Managerial
Emphasis, 13th ed., Pearson, 2009.
3. Khan, M Y. and Jain, P K, Cost Accounting and Financial Management, Tata McGraw-Hill, 2008.
 ME3126 SUPPLY CHAIN MANAGEMENT

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1 (10hours)
Introduction and a strategic view of supply chains, Evolution of Supply Chain Management (SCM),Importance
of the supply chain, Decision phases in a supply chain, Process views of supply chain, Enablers of supply chain
performance, Supply chain performance in India – challenges in maintaining supply chain in India, Supply
chain strategy and performance measures–competitive and supply chain strategies – customer service and cost
trade –offs,Achieving strategic fit, Supply chain performance measures –enhancing supply chain performance.
Module 2(11hours)
Supply chain drivers – framework for structuring drivers, Introduction to inventory management – types of
inventory – inventory related costs, Managing inventories in a supply chain – single stage inventory control,
Inventory control policies – periodic review and continuous review – deterministic and probabilistic models –
managing cycle stock, safety stock and seasonal stock, Impact of service level on safety stock, Analyzing
impact of supply chain redesign on the inventory – impact of centralization and decentralization on inventory –
choice of mode of transport.
Module 3(11 hours)
Drivers of transportation decisions–modes of transportation– choices and comparison of their performance
measures, Devising a strategy for transportation – distribution network design options for a transportation
network – cross docking practices, Vehicle scheduling in transportation –savings algorithm, Network design
and operation decisions –role of network design in the supply chain – factors influencing network design
decisions – framework for network design decisions.
Module 4(10hours)
Models for facility location and capacity allocation – network optimization models – capacitated plant location
models – gravity location models – network operations model, Strategic role of units in the network,
Innovations in supply chains– supply chain integration –internal and external, Bullwhip effect – quantifying the
bullwhip effect, Remedial strategies for coping with the bullwhip effect, Supply chain restructuring–
postponement – supply chain mapping – move from make to stock (MTS) to customer to order (CTO) model,
Enabling supply chain management through information technology .
References
1. Shah, J.,Supply Chain Management –Text and Cases, Pearson Education, 2009.
2. Chopra, S., and Meindel, P.,Supply Chain Management: Strategy, Planning, and Operation, Pearson
Prentice Hall of India, 2007.
3. Levi, D.S., Kaminsky, P., Levi, E.S., and Shankar, R., Designing and Managing the Supply Chain:
Concepts, Strategies, and Case Studies, Tata McGrawHill, 2008.
4. Chase, R.B., Shankar, R., Jacobs, F.R., and Aquilano, N.J.,Operation and Supply Chain Management,
Tata McGraw Hill, 2010.
5. Shapiro, J.F.,Modeling the Supply Chain, Thomson Learning, 2007.
6. Vollmann, T.E., Berry, W.L., Whybark, D.C., and Jacobs, F.R.,Manufacturing Planning and Control
for Supply Chain Management, Tata McGraw–Hill, 2006.
 ME3127 MANAGEMENT OF ORGANISATIONAL BEHAVIOUR

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1 (11 Hours)
Introduction to Organizational Behaviour (OB): - Development and challenges, assumptions of contemporary
OB. Foundations of individual behaviour values – attitudes – personality – emotions – perception – abilities –
motivation in organisations – work related attitudes.
Module 2 (11 Hours)
Group Process: Foundations of group behavior, understanding team, communication, leadership, power, conflict
and negotiation.
Module 3 (10 Hours)
Organisational Process: Work design and technology, organisation structure and design – organisational culture.
Module 4 (10 Hours)
Special topics: Organisational change, stress management, decision making in organisations.
References
1. Robbins, Organisational Behavior, 9th ed., Pearson Education, 2002.
2. Greenberg and Baron, Behavior in Organisations, 7th ed., Pearson Education, 2002.
3. Machane and Vonglinow, Organisational Behavior, 2nd ed., TMH, 2003.
4. Hersey, Balaschard and Johnson, Management of Organisational Behavior, 8th ed., Pearson Education,
2002.
 ME3128 PRODUCTION PLANNING AND CONTROL

Prerequisite: Nil
L T P C
Total Hours: 42 3 0 0 3
Module 1 (12 Hours)
Evolution of manufacturing planning and control (MPC) system – MPC system framework,Continuous
improvement,Process reengineering, Just-in-time principles – various kind and sources of waste in
manufacturing operations, Forecasting – forecasting for established and new product – time series analysis –
error measurement.
Module 2 (10 Hours)
Sales and operations planning – sales and operations planning process – strategic variables – relevant cost –
quantitative methods, Master production scheduling (MPS)– MPS technique – final assembly schedule –
freezing and time fencing.
Module 3 (10 Hours)
Material requirements planning (MRP) – advanced concepts in MRP – lot sizing– buffering concept –
nervousness, Just-in-time (JIT) – advanced concepts in JIT– pull production systems, Mixed model production
schedule.
Module 4 (10 Hours)
Shop-floor control and capacity analysis – hierarchy of capacity planning decisions – capacity planning and
control techniques – input/output control – frame work of shop-floor control – production activity control
techniques– advanced concepts in scheduling.
References
1. Vollmann, Berry, Whybark and Jacobs, Manufacturing Planning and Control for Supply Chain
Management, 5th ed., Tata McGraw-Hill Edition, 2005.
2. Nicholas, J.M., Competitive Manufacturing Management: Continuous Improvement, Lean production and
Customer – Focussed Quality, Tata McGraw Hill Edition, 2001.
3. Narasimhan, S.L., McLeavy, D.W., and Billington, P.J., Production planning and Inventory Control, 2nd
ed.,Prentice-Hall of India, 2000.
4. Tersine, R.J., Production and Operations Management: Concepts, Structure, and Analysis, 2nd ed., North-
Holland, 1985.
5. Monks, J.G., Operations Management: Theory and Problems, 3rd ed., McGraw-Hill International Edition,
1987.
6. Panneerselvam, R., Production and Operations Management, Prentice-Hall of India, 2001.
 ME3129 MANAGEMENT OF HUMAN RESOURCES

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1 (11 Hours)
Human Resource Management - Historical Evolution, Topology of companies, concept of an involved
employee, HR issues, Corporate and HR strategy - Linking Business and HR planning - HR instruments-
Diversity issues.
Module 2 (11 Hours)
Personnel Management: Personnel Functions – Personnel Management Environment in India – Manpower
Planning - Recruitment – selection and Induction of Employees – Staff Training and Development – Career
Planning – Job Analysis and Design – Compensation Planning – Salary Administration – Job Evaluation –
Merit Rating – Incentive Schemes.
Module 3 (10 Hours)
Industrial Relations: Managing Industrial Relations – Labour Laws – Trade Union – Employee Discipline –
Grievance handling mechanisms – Suspension, Dismissal and Retrenchment – Industrial Conflict Resolution –
Collective Bargaining – Productivity Bargaining – Workers, Participation in Management – Gold Collar
Employee Management – Recent issues in Industrial Relations – Turnover.
Module 4 (10 Hours)
Organizational Development: Organizational Design – Dimensions – Restructuring Strategies – Work
Organization – Organizational Development – Change Agents – Process of organizational change – Managing
Resistance to Change – Modules in OD – Role of Counseling.
References
1. Dwivedi, R.S., Manpower Management – An Integrated Approach to Personnel Management and Labour
Relations, PHI, 1984.
2. Yoder, D., and Staodohar P.D., Personnel Management and Industrial Relations, PHI 1986.
3. Monappa, A., and Saiyadain M. S., Personnel Management, TMH, 1988.
4. Kapoor, N.D., Introduction to Commercial and Industrial Law, Sultan Chand & Sons, New Delhi, 1986.
 ME3130 QUALITY PLANNING AND ANALYSIS

Prerequisite: Nil
L T P C
Total Hours: 42
3 0 0 3
Module 1 (10 hours)
Introduction – history, definition, Responsibility for quality, Total quality management – approach, Leadership,
Customer satisfaction, Employee involvement, Continuous process improvement, Supplier partnership, Cost of
poor quality.
Module 2 (12 hours)
Seven QC tools, Quality function deployment, ISO 9000, Bench marking, Poka yoke, Failure mode and effect
analysis, Design of experiments, Taguchi's quality engineering, Total productive maintenance.
Module 3 (10 hours)
Statistical quality control – fundamentals – assignable causes, Rational subgrouping, Control charts for
variables – average range chart, average standard deviation chart, control charts for attributes – chart for
fraction non-conforming, chart for count of non-conformities, Process capability, Six sigma.
Module 4 (10 hours)
Acceptance sampling – operating characteristic curve, Types of sampling plans, Acceptance quality level,
Average outgoing quality, Sampling plan design, Reliability – life-history curve, System reliability, Testing.
References
1. Besterfield, D.H., Quality Control, 7th ed., Pearson Education, 2006.
2. Juran, J. M. and Gryna, F. M., Quality Planning and Analysis, 3rd ed., Tata McGraw Hill, 1995.
3. Grant, E.L. and Leavenworth, R.S., Statistical Quality Control, 7th ed., Tata McGraw-Hill, 2000.
 ME4021 INDUSTRIAL TRIBOLOGY

Prerequisite 1: ME2001 Fluid Mechanics/ ME2004 Fluid Mechanics and Machinery

L T P C
Prerequisite 2: ME2012Applied Mechanics of Solids/
ME2015 Theory of Elasticity and Plasticity 3 0 0 3

Total Hours: 42
Module 1 (11 hours)
Introduction – Basic equations,Derivation of Reynolds equation, Energy equation, Idealized hydrodynamic
bearings, Mechanism of pressure development, Plane slider bearings, Idealized journal bearings, Infinitely long
and short bearings.
Module 2 (11 hours)
Finite bearings – performance characteristics – numerical solution, Hydrodynamic instability, Design of journal
bearings, Analysis of externally pressurized and gas lubricated bearings.
Module 3 (10 hours)
Costs of wear, Surface topography, Mechanics of contact, Theories of friction, Friction of metals and non-
metals, Temperature of sliding surfaces, Stick-slip, Rolling friction.
Module 4 (10 hours)
Wear of metals, Adhesive wear, Abrasive wear, Corrosion and corrosion wear, Erosion,Surface fatigue and
impact wear, Wear of elastomers, Wear of ceramics and composite materials, Measurement of friction and
wear.
References
1. Majumdar, B.C.,Introduction to Tribology, 4th ed., A.H. Wheeler, Bangalore, 1978.
2. Pinkus and Sternlincht, Theory of hydrodynamic lubrication, John Wiley&Sons, New York, 1961.
3. Moore, D. F.,Principle and Application of Tribology, Pergamon Press, New York, 1975.
4. Rabinnowicz, E.,Friction and Wear of Metals, John Wiley & Sons, New York, 1995
5. Johnson, K.L.,Contact Mechanics, CambridgeUniversity Press, 1985.
6. Thomas, T.R.,Rough Surfaces, Longman Inc., 1982.
 ME4022 VEHICLE DYNAMICS

Prerequisite: ME2003Engineering Mechanics – Dynamics L T P C

Total hours: 42 3 0 0 3

Module 1 (11 Hours)

Introduction to vehicle dynamics, Acceleration performance, Braking performance, Aerodynamics and rolling
resistance, Steady-state cornering, Suspensions– steering systems, Rollover-acceleration – braking and turning
forces.
Module 2 (11 Hours)
Front wheel geometry–effects of front wheel geometry on vehicle performance, Dynamic axle Loads, Transient
rollover, Acceleration–Traction limited acceleration–Power limited acceleration–Road friction, Rear wheel
lockup, Drag forces, Total road loads, Vibration, Roll center analysis.
Module 3 (10 Hours)
Tyre construction –Types- Types of tyers–Basic Tyre modelling considerations–Tyre forces on hard surfaces–
Tyre-soil interaction, Characterizing typical terrains for mobility analysis.
Module 4 (10 Hours)
Sensors, Actuators, Cruise control, Antilock braking system (ABS), Traction control, Directional control,
Vehicle stability controls, Active suspension, Computer aided analysis/Simulation–Simulation with MATLAB-
Simulink and ADAMS.
References
1. Thomas D. Gillespie, Fundamentals of Vehicle Dynamics, Society of Automotive Engineers, 1992.
2. Wong,J.Y., Theory of Ground Vehicles, John Wiley and Sons, 3rd ed., 2001.
3. Hans Pacejka, Tyre and Vehicle Dynamics, SAE Publications, 2nd ed., 2005.
4. Blundell,M. and Harty,D., The Multi body Systems Approach to Vehicle Dynamics, Elsevier Publications,
2004.
 ME4023 INTRODUCTION TO ROBOTICS

Prerequisite: Nil
L T P C
Total Hours: 42
3 1 0 3
Module 1 (11 hrs)
Brief History, Types and applications of robots. Present status and future trends in robotics, Overview of robot
subsystems. Challenges in robotics, Characteristics of robots, Robot configurations and concept of work space,
Types of actuators and sensors in robotics, Types of grippers.
Module 2 (10 hrs)
Introduction to Manipulator Kinematics, Position and orientation of rigid bodies, Planar and spatial mechanism
description, Homogenous transformations, Denavit - Hartenberg (DH) notation, Forward and inverse kinematic
analysis, Examples.
Module 3 (11 hrs)
Linear and rotational velocity of rigid bodies, Velocity propagation from link to link, Jacobians, Singularities,
Static forces in manipulators, Jacobians in force domain, Cartesian transformation of velocities and static
forces. Forward and Inverse Dynamics, Lagrangian and Newton – Euler’s formulation methods, Examples.
Module 4 (10 hrs)
Trajectory Generation, General consideration in path description and generation, Joint space schemes, Collision
free path planning, Robot programming. Robot Control, Independent joint control, PD and PID feedback, Issues
in nonlinear control, Examples.
References
1. Craig, J.J.,Introduction to Robotics, Mechanics and control, 2nd ed., Pearson Education, 1999.
2. Spong, M.W., and Vidyasagar, M.,Robot Dynamics and Control, John Wiley and Sons, 1989.
3. Groover, M.P., Weiss, M., Nagel, R.N.,and Odrey,N.G., Industrial Robotics: Technology,
Programming and Applications, McGraw Hill Publishers, 1986.
4. Paul, R.P.,Robot Manipulators Mathematics Programming, Control: The computer control of robotic
manipulators, MIT Press, 1979.
5. Schilling, R.J.,Fundamentals of Robotics, Analysis and Control, Prentice Hall of India, 1996.
6. Niku, S.B., Introduction to Robotics: Analysis, Systems, Applications, John Wiley and Sons, 2010.
 ME4024 DESIGN FOR MANUFACTURABILITY

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3

Module 1 (9 hours)
Introduction – Design philosophy, implementing DFM, Benefits of DFMConcurrent Engineering – Design for
quality, Design for Life Cycle, Design for Cost, Enabling Technology, Concurrent Engineering and the
Organization, Improving the Development process. Management Frameworks – Architecture, Management’s
concerns with Manufacturability, TeamBuilding and Training. Team Building and Training -Justification of
DFM, Viewpoints for DFM.
Module 2 (9 hours)
Quality Tools in DFM – Problem Solving Tools, Quality Function Deployment, Benchmarking, Computer
Improvement, Taguchi approach. Computer Aided Technology – CAD/CAM/CAE, Rapid Prototyping, Group
Technology, CIM Creative Thinking in DFM, Tools. General Product Design – Impact of Design concept and
early project decisions, Evaluating manufacturability of conceptual designs, Producibility, Geometric
Tolerancing.
Module 3 (12 hours)
Design for Assembly – Principles, improving serviceability, recyclability. Design for Machining – Principles,
Non-Traditional Machining. Design for forming – Principles, fine blanking, roll forming, precision forming,
metal spinning, tube fabrication.
Module 4 (12 hours)
Design for Forging, Casting. Design for Coating – Painting, powder coating, metal spraying. Design for Heat
Treatment. Design for Fastening & Joining – Design guidelines for fasteners, adhesive assembly, and welded
assemblies. Design for Materials: Plastics, Composites, Ceramics, Powder Metallurgy.
References
1. Chitale, A.K., and Gupta, R.C., Product Design and Manufacturing, Prentice-Hall Of India Pvt. Ltd, 2004.
2. Dieter, G.E., and Schmidt, L.C., Engineering Design: A Materials And Processing Approach, 4th ed.,
McGraw Hill, 2009.
3. Bakerjian, Ramon, Ed., Design for Manufacturability,Tool & Manufacturing Engineers Handbook, Society
of Manufacturing Engineers, 1992.
 ME4025 MECHATRONICS

Prerequisite: Nil
L T P C
Total Hours: 42
3 0 0 3
Module 1 (10 Hrs)
Introduction to mechatronics Systems, Key elements, Mechatronics design process, Types of design –
Traditional and mechatronics designs, Information systems, Real time interfacing (Hardware-in-the loop
simulation), Elements of data acquisition system.
Module 2 (11 Hrs)
Introduction to actuators, sensors and transducers, Mechanical, fluid power and electrical actuators, Actuator
selection criteria, Performance characteristics of sensors, Sensors for position, motion, force and temperature,
Flow sensors, Range sensors, Ultrasonic sensors, Fibre optic sensors, Selection of sensors. Special transducers -
Piezoelectric transducer - Magnetostrictive transducer - Shape memory alloy (SMA) transducer.
Module 3 (11 Hrs)
Introduction to signals, system and controls, System representation, Linearisation, Time delays, Measures of
system performance, Closed loop controllers – PID controller – Digital controllers, Controller tuning, Adaptive
control, Supervisory control, Introduction to microprocessors, Microcontrollers and programmable logic
controllers, Components,PLC programming.
Module 4 (10 Hrs)
Introduction to MEMS, Microsensors in mechatronics, Sensors for condition monitoring, Artificial intelligence
in mechatronics, Introduction to fuzzy logic control and neural networks, Case studies of mechatronics systems.
References
1. Bolton, W., Mechatronics, Pearson Education Asia, 2004.
2. Shetty, D.,and Kolk, R.A.,Mechatronics System Design, Thomson Learning, 2001
3. Necsulescu, D., Mechatronics, Parson Education Asia, 2002.
4. H.M.T. Ltd, Mechatronics, Tata McGraw Hill Publishers, 1998.
5. Singh, B.P.,Microprocessors and Microcontrollers, Galgotia Publishers, 1997.
6. Petruzella, F.D., Programmable Logic Controllers, Tata McGraw Hill Publishers, 1989.
7. Kant, K., Computer Based Industrial Control, Prentice Hall India, 1999.
 ME4026 UNCONVENTIONAL ENERGY SYSTEMS

Prerequisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module 1 (12 hours)
Introduction – energy problem – finite conventional energy sources – energy and environment–need for
renewables and energy efficiency, Solar energy – measurement of solar radiation –estimation of terrestrial solar
radiation – methods of solar collection and thermal conversion –thermal analysis of flat plate collectors – testing
procedures – solar pond – parabolic collectors – paraboloid dish – central receiver, Energy storage systems,
Applications of solar thermal systems – residential water heating – industrial heating – power generation.
Module 2 (10 hours)
Biomass energy systems – biomass conversion routes – combustion – gasification – anaerobic digestion –
pyrolysis – cogeneration, Performance analysis and testing, Thermal applications – power generation.
Module 3 (10 hours)
Wind energy conversion – wind distribution – types and operation of wind turbines and their characteristics –
generators and control strategies, Small hydro power – classification of hydro turbines – performance analysis –
selection and sizing, Ocean thermal energy conversion–power generation options, Wave and tidal energy –
systems for power generation.
Module 4 (10 hours)
Economic analysis – calculation of energy cost from renewables – comparison with conventional energy
systems, calculation of carbon dioxide reduction – incremental costs for renewable energy options, Introduction
to integrated energy systems.
References
1. Sukhatme, S.P., and Nayak, J.K., Solar Energy-Principles of Thermal Collection and Storage, 3rd ed., Tata
McGraw Hill, 2008.
2. Duffie, J.A., and Beckman, W.A., Solar Engineering of Thermal Processes, 3rd ed., Wiley, 2006.
3. Goswami, D.Y., Kreith, F., and Kreider, J.F., Principles of Solar Engineering, 2nd ed., Taylor and Francis,
2003.
4. Twidell, J. and Weir T., Renewable Energy Resources, 2nd ed., Taylor and Francis, 2006.
5. Boyle, G. (Ed.), Renewable Energy, 2nd ed., Oxford University Press, 2004.
6. Deublein, D., and Steinhauser A., Biogas from Waste and Renewable Resources: An Introduction, 2nd ed.,
Wiley, 2010.
 ME4027 COMPUTATIONAL FLUID DYNAMICS
L T P C
3 0 0 3
Prerequisite: Nil
Total Hours: 42
Module 1 (10 hours)
Introduction to analytical, numerical and computational methods, Mathematical description of physical
phenomena, Physical significance for mathematical classifications of partial differential equations as elliptic,
parabolic and hyperbolic, Physical meaning of general partial differential equations, Simplification methods –
proper choice of coordinate – transformed coordinates – normalization, Physical domain and computational
domain, Discretization methods for converting derivatives to their finite difference forms – Taylor series
method – polynomial fitting method – integral method and physical formulation, Discretization error, first
order, second order and higher order accuracy discretization methods.
Module 2 (10 hours)
Model equations– Laplace’s equation – heat equation – first order wave equation – Burger’s equation
(INVISCID), Computational methods for one, two, three-dimensional steady state conduction problem in
Cartesian and cylindrical co-ordinates, Methods to deal Dirichlet, Neumann and Robins type boundary
conditions for regular and irregular shapes, Fine, coarse, uniform and non-uniform grids, Solution of the linear
algebraic equations – Gaussian elimination method – Tri-diagonal Matrix Algorithm (TDMA), Iterative
methods – Gauss-Seidel point by point method – Gauss Seidel line by line methods – under and over
relaxations.
Module 3 (10 hours)
Computational Methods for one, two and three-dimensional heat equations - explicit, implicit, Crank-
Nicholson, ADI schemes, ADE schemes, Fractional step methods, Hopscotch scheme, Douglass scheme,
Conservative form of partial differential and finite difference equations, Methods to deal interface property and
non linearity, Consistency, stability and convergence of computational methods, Discrete perturbation stability
analysis, Von- Neumann stability analysis, Validation of computational solution.
Module 4 (12 hours)
Computational methods of first order wave equations and Burger’s Equation (INVISCID) –explicit schemes –
implicit schemes – upstream difference schemes – Lax–Wendroff scheme – Mac Cormack – hybrid and power
law schemes, Dissipation and dispersion errors,Four basic rules to obtain consistency and stability, Computation
of the flow field using stream function-vorticity formulation, Analysis of two dimensional incompressible
viscous flow inside a Lid Driven Cavity, Algorithms to obtain flow field by solving coupled system of
equations – semi implicit methods for pressure linked equations and its revised schemes.
References
1. Anderson, D.A., Tennehill J.C.,and PletecherR.H., Computational Fluid Mechanics and Heat Transfer,
Hemisphere, 1984.
2. Patankar, S.V. Numerical Heat Transfer and Fluid Flow, Hemisphere, 1980.
3. Muraleedhar, K., and Sundararajan, T. Computational Fluid Flow & Heat Transfer, Narosa, 1995.
4. Versteeg, H.K. & Malalasekera, W.Anintroduction to computational fluid Dynamics: The Finite Volume
Method, Adison Wesley-Longman, 1995.
5. Roache, P.J. Computational Fluid Dynamics, 2edn, Hermosa, 1982.
6. Hornbeck, R.W. Numerical Marching Techniques for Fluid Flows with Heat Transfer NASA, SP-297,
1973.
7. Hoffmann Klaus. A.,Computational Fluid Dynamics for Engineers-Volume I, Engineering Education
System, Wichita, 1993.
 ME4028 AERODYNAMICS

Prerequisite: ME2001 Fluid Mechanics L T P C

Total Hours: 42 3 0 0 3

Module 1 (11 hours)

Equations for incompressible inviscid flows, Fluid circulation and rotation –vorticity - Kelvin’s theorem -
velocity potential - stream function -equation of a stream line -complex potential, Blasius theorem for force and
moment on bodies, Elementary flow patterns and their superposition.
Module 2 (11 hours)
Flow past a cylinder - Magnus effect - Kutta condition - Vortex theory of lift. Conformal transformation, The
Joukowski transformation -lift on arbitrary cylinder, Aerodynamic center, Pitching moment.
Module 3 (10 hours)
Aerofoils -low speed flows over aerofoils - the vortex sheet, Thin aerofoil theory -symmetric aerofoil, Tear drop
theory, Camber line at zero angle of attack, Characteristics of thin aero foils, Motion in three dimensions, Flow
past slender bodies.
Module 4 (10 hours)
Finite wings -downwash and induced drag - Prandtl-Lachester theory - Biot- Savart law, General series
solution, Glauret method, Multhop’s method, Horseshoe effects, Ground effects, Lineraised compressible flows
in two dimensions -flow past a wavy wall, Similarity rules, Aerofoil in compressible flows.

References
1. Anderson ,J.D., Fundamentals of Aerodynamics, 5th ed., McGraw Hill, New York, 1998
2. Kuethe,A.M., and Chow,C., Foundations of Aerodynamics, Fourth Edition, Wiley Eastern, New Delhi,
1986.
3. Katz,J.,and Plotkin,A.,Low Speed Aerodynamics, McGraw Hill, New York, 1991.
4. Houghton,E.L., and Brock,A.E.,Aerodynamics for Engineering Students, Edward Arnold, London,
1960.
 ME4029 HEATING, VENTILATION AND AIR CONDITIONING

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3

Module 1 (11 Hours)

Principles of refrigeration -- Carnot refrigeration cycle -- unit of refrigeration – capacity -- coefficient of
performance.
Refrigeration systems -- vapour compression system – theoretical and practical cycles – system components –
compressors – condensers – expansion devices – evaporators – refrigerants.
Air refrigeration cycle, Vapour absorption refrigeration system.
Module 2 (11 Hours)
Psychrometry – psychrometric processes – determination of condition of air entering conditioned space.
Air conditioning systems – summer, winter and year-round-year air conditioning systems -- central and unitary
systems.
Requirement of air conditioning – human comfort –comfort chart and limitations – effective temperature –
factors governing effective temperature – design considerations.
Module 3 (10 Hours)
Cooling load calculations – various heat sources contributing heat load – solar load -- equipment load --
infiltration air load -- duct heat gain -- fan load -- moisture gain through permeable walls and fresh air load,
Design of air conditioning systems.
Duct design – equal friction method -- static regain method -- velocity reduction method, Air distribution
systems, Analysis for heating and cooling systems, Insulation.
Module 4 (10 Hours)
Heating systems – warm air systems – hot water systems – steam heating systems – panel and central heating
systems, Heat pump circuit, Heat sources for heat pump.
Air conditioning equipments and control systems – air filters – humidifiers – fan – blowers – control systems
for temperature and humidity – noise control.
Installation and charging of refrigeration unit, Testing for leakage, Cause for faults and rectification.
References
1. Noman C. Harris,Modern Air conditioningPractice, 2nd ed.,McGraw-Hill, 1974.
2. Stoecker, W.F.,Refrigeration & Air conditioning, 2nd ed., McGraw Hill, New York, 1987.
3. Dossat, R.J.,Refrigeration & Air conditioning, 4th ed., prentice hall, 1997.
4. Arora, C.P.,Refrigeration & Air conditioning, 2nd ed., McGraw Hill,, 2000.
5. Stoecker, W.F.,Principles of Air conditioning, 2nd ed., industrial press, 1977.
6. Laub, J.M.,Heating & air conditioning of buildings, Holt, Rinehart and Winston, 1963.
7. Kell, J.R., and Martin, P.L.,Air conditioning & Heating of buildings,6th ed.,Architectural Press,2007.
8. Carrier’s Handbook for Design of Unit Air Conditioners,14th ed., Kenrick Place Media Ltd,1996.
 ME4030 FUNDAMENTALS OF COMBUSTION
Prerequisite: ME2014 Thermodynamics L T P C
3 0 0 3
Total Hours: 42
Module 1 (12hours)
Introduction to combustion, Flames classification, First law of thermodynamics, Combustion stoichiometry,
Reactants and products, Standard enthalpies and enthalpy of formation – Enthalpy of combustion and heating,
Adiabatic flame temperatures, Second law of thermodynamics - Gibb’s function.
Module 2 (11 hours)
Chemical kinetics, Global and elementary reactions, Reaction rates, Rate laws and reaction orders, Temperature
and pressure dependence on rate coefficients, Unimolecular and bimolecular reactions – Chain and chain-
branching reactions, H2–O2chemical mechanisms, Explosion limits.
Module 3 (12hours)
Premixed laminar flames – Laminar flame structure, Flame velocity and flame thickness, Simplified analysis of
laminar flame, Effect of equivalence ratio on flame speed and flame thickness, Flame quenching and ignition -
Flammability limits, Laminar diffusion flames – Structure of diffusion flame from Laminar Jets.
Module 4 (7hours)
Introduction to turbulent flames,Droplet combustion and its applications – Simple Model for evaporating and
burning droplet - D2 Law - Pollutant emissions - Effects of Pollutants - Emission Index.
References
1. Stephen R.T.,An Introduction to Combustion: Concepts and Applications, 2nd ed., McGraw-Hill, 2000.
2. Kuo, K.K., Principles of Combustion, 2nd ed., Wiley - Interscience, 2005.
3. Warnatz, J., Maas, U., and Dibble, R.W., Combustion: Physical and Chemical Fundamentals,
Modelling and Simulation, Experiments, Pollutant Formation, 4th ed., Springer-Verlag, 2005.
4. Glassman, I., and Yetter, R.A., Combustion, 4th ed., Academic Press, 2008.
5. Williams, F.A., Combustion Theory, 2nd ed., Westview Press, 1994.
6. Borman, G, and Ragland, K., Combustion Engineering, McGraw Hill, 1998.
 ME4031 REFRIGERATION AND AIR CONDITIONING SYSTEMS

Prerequisite: Nil L T P C
Total Hours 42 3 0 0 3
Module 1 (11 Hours)
Principles of refrigeration – Carnot refrigeration cycle – Various methods of producing cold, Performance
parameters – capacity – Coefficient of performance (COP), Refrigeration systems – Vapour compression
system – theoretical and practical cycles, System components – Compressors – Condensers – Expansion
devices – Evaporators, Other refrigeration systems – Vapour absorption system – Air cycle refrigeration –
Steam jet refrigeration–thermo electric cooling and magnetic refrigeration, Introduction to liquefaction systems
Cascading – simple Linde Hampson system – Claude cycle liquefier.

Module 2 (11 Hours)

Vapour compression refrigeration system – theoretical and practical cycles – simple and multi-pressure systems
– thermodynamic analysis, System components – Compressors – Reciprocating compressors – single and
multistage compressors – work of compression – effect of clearance – effect of inter-cooling – optimum
pressure ratio – efficiencies – rotary compressors – screw type and vane type compressors – hermetic, semi
hermetic and open compressors, condensers – water cooled and air cooled condensers – evaporative condensers,
expansion devices – capillary tube – constant pressure expansion valve – thermostatic expansion valve – float
valve, evaporators – natural, Vapour absorption system – principle of operation of aqua – ammonia and lithium
bromide – water systems – electrolux system – comparison between vapour compression and absorption
systems, Refrigerants – thermodynamic, physical and chemical properties of refrigerants – Selection criteria of
refrigerants, designating refrigerants.

Module 3 (10 Hours)

Psychrometry – psychrometric processes – determination of air entering conditioned space, Requirement of air
conditioning – human comfort – comfort chart and limitations – effective temperature – factors governing
effective temperature – design considerations – inside design condition, ventilation standards, Applied
psychrometry, summer air conditioning processes, winter air conditioning processes, Other air conditioning
systems – summer – winter and round the year air conditioning systems – central and unitary systems.

Module 4(10 Hours)

Cooling load calculations – various heat sources – solar load – equipment load – infiltration air load – duct heat
gain – fan load – moisture gain through permeable walls and fresh air load, design of air conditioning systems –
Duct design – equal friction – static regain and velocity reduction methods – distribution systems – insulation,
Analysis for heating and cooling systems, Air conditioning equipments and control systems – air filters –
humidifiers – fan – blowers – control systems for temperature and humidity – noise and noise control.

References
1. Stoecker, W.F., Refrigeration & Air Conditioning, McGraw Hill, New York, 1958.
2. Stoecker, W.F., & Jones J.W., Refrigeration & Air Conditioning, McGraw Hill, New York, 1982.
3. Dossat, Refrigeration & Air Conditioning, 2nd ed., Wiley Eastern Limited, New Delhi, 1989.
4. Jordan & Priester, Refrigeration & Air Conditioning, 2nd ed., Prentice Hall India Pvt. Ltd, 1985.
5. Arora,C.P., Refrigeration & Air Conditioning, Tata McGraw Hill, New Delhi, 1995.
6. Stoecker W.F., Principles of Air Conditioning, Industrial Press, New York, 1968.
7. Laub, Heating & air conditioning of Buildings, Holt, Rinehart & Winston, New York, 1963.
8. Kell & Marting, Air conditioning & Heating of Buildings, Baltonworth, New York, 1995.
9. Carrier’s Handbook for Design of Unit Air Conditioners, McGraw Hill Book Co, New York, 1965.
10. Threlkeld, J. L., Thermal Environmental Engineering, 2nd ed., Prentice Hall, 1970.
11. Norman C. Harris, N. C., Modern Air Conditioning Practice, 3rd ed., McGraw Hill, 1985.
12. Levenhagen, J. L., Spethmann, D. H., Heating Ventilating and Air Conditioning Controls and Systems, McGraw
Hill1, 1993.
13. Carrier Design hand book
14. ASHRAE hand book
 ME4032 AUTOMOBILE ENGINEERING

Prerequisite : Nil L T P C
Total Hours: 42 3 1 0 3

Module 1 (9 Hours)
Constructional details of engines - engine parts - piston - different types - piston rings cylinder block -
cylinder head - gudgeon pin - connecting rod - bearing bushes - different type of bearings, Cooling system-
purpose of cooling - types of cooling systems - air cooling - water cooling - radiator - types of radiators -
constructional details - thermostat - temperature indicators.

Module 2 (13 Hours)

Lubrication - purpose of lubricating systems - grading of oils - oil pumps - oil filters - oil pressure indicators,
Fuel systems - fuel system components - fuel tank - fuel filters and screens - fuel gauges - fuel pumps,
Carburetors - idle and low speed circuits - high speed part load circuit - full power circuit - choke, Electronic
fuel injection system, Gasoline Direct injection system, Air assisted fuel injection system, Diesel injection
system - Common rail Direction Injection system, Ignition system - Battery and coil ignition - Electronic
Ignition system - Distributor less Ignition system

Module 3 (12 Hours)

Transmission - clutch - types of clutches - single and multi plate clutches - centrifugal clutch, Fluid coupling,
Torque converter, Gear box - sliding mesh - constant mesh - synchro mesh, Propeller shaft, Universal
coupling, Differential, Axle - semi floating - three - fourth floating - fully floating, Brakes - mechanical and
hydraulic brakes - vacuum - servo and air brakes - components of braking systems and their functions -
constructional details, Anti lock braking system. Steering mechanism - steering geometry - steering gears -
worm and wheel gears - power assisted steering.

Module 4 (8 Hours)
Vehicle body terminology, Chassis and suspension - chassis lay out, Independent suspension - Road springs -
Shock absorbers - torsion bars, Air suspension systems, Wheels - tyres and tubes, Starting mechanism - starter
drives - over running clutch. Electrical equipments - battery - battery charging - charging circuit – regulators.
Air pollution and control - Pollution rating - Catalytic converters, Exhaust Gas circulation, Turbocharger.

References
1. Joseph Heitner,Automotive mechanics Principles and Practices,2nd ed.,D. Van Nostrand Company, 1967.
2. Newton. K and Steeds.W.,The Motor Vehicle, The English Language Book Society and Newnes Butterworth,
London, 1972.
3. William H Crouse and Donald L Anglin, Automotive Mechanics,10th ed., Pearson Higher Education, 1993.
4. William H Crouse and Donald L Anglin, Automotive engine, 8th ed., McGraw-Hill, 1994.
5. William H Crouse and Donald L Anglin, Automotive fuel - lubricating and cooling systems.6th ed., McGraw-
Hill, 1981.
6. William H Crouse and Donald L Anglin, Automotive chassis and body.5th ed., McGraw-Hill, 1975.
7. William H Crouse, Automotive electrical equipments.8th ed., McGraw-Hill, 1976.
8.Kirpal Singh,Automobile Engineering Vol.I & II,8thed., Standard Publishers Distributors, Delhi, 1999.
 ME4033 INTRODUCTION TO COMPUTER GRAPHICS

Prerequisite: ZZ1004 Computer Programming

L T P C
Total Hours: 42 3 0 0 3
Module 1 (11 hours)
Introduction to computer graphics-Overview of computer graphics, Mathematics for computer graphics -
Representing and interfacing with pictures, Description of graphic devices, Raster Scan Graphics, Algorithms
for generating line, circle and ellipse – Polygon filling - Fundamentals of anti-aliasing.
Module 2 (11 hours)
Two-dimensional transformations, Three-dimensional transformations – scaling, shearing, rotation, reflection,
translation. Affine and perspective geometry - Orthographic, axonometric and oblique projections: perspective
transformations.
Module 3 (10 hours)
Plane curves, non-parametric and parametric curves: Space curves – Representation of space curves, cubic
spline, Bezier curves, B-spline curves, NURBS.
Module 4 (10 hours)
Surface description and generation- Surface of revolution, Sweep Surface, Linear Coons surface, Bezier
surface, B-Spline surface, B-Spline surface filling, Introduction to solid modelling, Hidden lines and Hidden
Surfaces.
References
1. Rogers, D.F., and Adams, J.A., Mathematical Elements for Computer Graphics, 2nd ed., Tata McGraw Hill,
2009.
2. Rogers, D.F., Procedural Elements for computer Graphics,2nd ed., Tata McGraw Hill, 1997.
3. Hearn, D., and Baker, M.P., Computer Graphics, 2nd ed., Prentice Hall of India Private Limited, 2007.
4. Foley, J.D., Dam, A.V., Feiner, S.K., and Hughes, J.F., Computer Graphics: Principles and Practice in C,
2nd ed., Addison-Wesley Professional, 1995.
5. Mortenson,M.E., Geometric Modeling, 2nd ed., John Wiley & Sons, 1997.
 ME4034 EXPERIMENTAL METHODS IN FLUID FLOW AND HEAT TRANSFER

Prerequisite: Nil
L T P C
Total Hours: 42
3 0 0 3
Module 1 (11hours)
Introduction to experimental methods – basic concepts – accuracy – precision– resolution– uncertainty, Pressure
measurements – dynamic response considerations – dead-weight tester – bourdon-tube pressure gage –
diaphragm and bellows gages – bridgman gage – pirani thermal-conductivity gage – knudsen gage – ionization
gage – alphatron.
Module 2 (11 hours)
Flow measurement – passive-displacement methods – flow-obstruction methods – sonic nozzle – flow
measurement by drag effects – pressure probes – hot-wire and hot-film anemometers – magnetic flowmeters,
Flow visualization methods – smoke methods – shadowgraph – schlieren photography – laser doppler
anemometer – laser-induced fluorescence – particle image velocimetry.
Module 3 (10 hours)
Temperature measurements – temperature scales – ideal-gas thermometer – temperature measurement by
mechanical effects – temperature measurement by electrical effects – temperature measurement by radiation –
transient response of thermal systems – thermocouple compensation – temperature measurements in high-speed
flow – interferometric method.
Module 4 (10hours)
Transport-property measurements – thermal conductivity measurements – measurement of viscosity – gas
diffusion – calorimetry – convective heat transfer measurement – humidity measurement – heat flux meters –
pH measurement, Thermal-radiation measurements – emissivity measurement – reflectivity and transmissivity
measurement – solar radiation measurement.
References
1. J.P. Holman, Experimental Methods for Engineers, McGraw-Hill Company.
2. Figliola, Richard S, & Beasley, Donald E, Theory and Design for Mechanical Measurements,Third edition,
John Wiley & Sons Inc.
3. Doebelin, Ernest O., Measurement Systems, 4th edition, McGraw-Hill International.
 ME4122 MECHANICAL BEHAVIOUR AND TESTING OF MATERIALS

Prerequisite: ME2101 Materials Science and Metallurgy

L T P C
Total Hours: 42 3 0 0 3
Module 1 (8 hours)
Concepts of crystals, Plastic deformation by slip and twinning, Slip systems in FCC, BCC and HCP lattices,
Critical resolved shear for slip, Theoretical shear strength of solids, Stacking faults and deformation bands.
Module 2 (14 hours)
Observation of dislocations, Geometric properties of dislocations, Edge and screw dislocations, Climb and cross
slip, Dislocations in FCC and HCP lattice, Partial dislocations, Stress fields and energies of dislocations, Forces
between dislocations. Applications of dislocation theory, Strengthening from grain boundaries, Grain size
measurements, Yield point phenomenon, Strain aging, solid solution strengthening, Strengthening from fine
particles, Fiber strengthening, Cold working and strain hardening, Annealing of cold worked metal.
Module 3 (12 hours)
Fracture in metals, Griffith theory of brittle fracture, Metallographic aspects of fracture, Fractography,
Dislocation theories of brittle fracture, Ductile fracture, Notch effects, Fatigue of metals, The S-N curve, Low
cycle fatigue, Fatigue crack propagation, Effects of metallurgical variables and fatigue, Corrosion fatigue,
Effect of temperature on fatigue. Creep and stress rupture, Creep curve, mechanism of creep formation, Stress
rupture test, Activation energy for steady state creep, Fracture at elevated temperature, Creep resistant alloys.
Module 4 (8 hours)
Tension test, Stress-strain curves, Instability in tension, Ductility measurement, Effect of strain rate,
temperature and testing machine on flow properties, Stress relaxation testing. Hardness test, Brinell, Rockwell
and Vickers hardness, flow of metal under the indenter, relationship between hardness and flow curve, micro
hardness testing. Torsion test, Mechanical properties in torsion, Torsion stresses for large plastic strains, Types
of torsion failures, and torsion testing.
References
1. George, D.M., Mechanical Metallurgy, McGraw – Hill Inc, 2001.
2. Hertzberg, R.W., Deformation and Fracture Mechanics of Engineering Materials, 4th ed., John Wiley &
Sons, 1995.
3. McClintock, F.A., and Argon, A.S., Mechanical Behavior of Materials, 1st ed., Addison-Wesley
Publications, 1966.
4. Reed Hill, R.E.,Physical Metallurgy Principles, 2nd ed., Affiliated East-West Press, 2008.
5. Hayden, H.W., Structure And Properties Of Materials: Mechanical Behaviour Vol. 3 (Structure &
Properties Of Materials), John Wiley & Sons Inc, 1965.
6. Honeycombe, R.W.K., Plastic Deformation of Metals, 2nd ed., Edward Arnold, 1984.
 ME4123 TECHNOLOGY MANAGEMENT

L T P C
Prerequisite: Nil
3 0 0 3
Total Hours: 42
Module 1 (12 hours)
Technology – definition and characteristics, Management of technology, Process of technological change,
Technology life cycles – the S-curve of technological process, Diffusion of technology.
Module 2 (10 Hours):
Critical factors in managing technology, Technology and competition – competitive consequences of
technological change.
Module 3 (10 Hours):
Technology Strategy – strategic impact of technology – Transfer of technology -Technology intelligence –
Collaborative mode, Appropriation of technology.
Module 4 (10 Hours):
Technology evaluation and financing, Technology audits, Intellectual property rights – patents – trade secrets –
trade marks – copyrights.
References
1. Khalil, T., Management of Technology, TataMcGraw-Hill, 2009.
2. Narayanan, V.K., Managing Technology and Innovation for Competitive Advantage, Pearson Education
Asia, 2001.
3. Burgelman,R.A.,Christensen,C.M.,andWheelwright,S.C.,StrategicManagementofTechnologyInnovation,
McGraw-Hill, 2004.
4. Shane, S., Technology Strategy for Managers and Entrepreneurs, Pearson Education, Inc., 2009.
5. Gaynor, G.H., Handbook of Technology Management, McGraw-Hill, 1996.
 ME4125 COMPETITIVE MANUFACTURING MANAGEMENT

Pre-requisite: Nil
Total Hours: 42 L T P C
3 0 0 3
Module1 (10 hours)
Evolution of manufacturing, Modern developments, E-manufacturing – e-manufacturing and supply chain –
business process design models and concepts, Continuous improvement, Process reengineering, Basic problem
solving and improvement tools, Just-In-Time (JIT) – value added focus – sources of waste – JIT Principles.
Module 2 (10 hours)
TQM – framework for managing total quality – employee involvement – benchmarking – quality certification
and awards, Statistical process control – variation in processes – control charts – process capability, Six sigma
quality – methodology.
Module 3 (10 hours)
Lean production – small lot production – setup time reduction – pull production – pull and push systems –
kanban.
Module 4 (12 hours)
Focused factories and group technology – ways of doing work – facility layout – part families and machine
groups – production flow analysis, Cellular manufacturing – part family/machine cell formation methods –
linked cells – workcell design – workcell capacity – staffing a workcell.
References
1. Nicholas, J., Competitive Manufacturing Management – Continuous Improvement, Lean Production, and
Customer-Focused Qualities, McGraw-Hill Edition, 2001.
2. Greeff, G., and Ghoshal, R., E-manufacturing and Supply Chain Management, Elsevier, 2004
3. Sing, N., and Rajamani, D., Cellular Manufacturing Systems: Design, Planning & Control, 1sted.,
Chapman & Hall, 1996.
4. Askin, R.G., and Standridge, C.R., Modelling and Analysis of Manufacturing Systems, John Wiley & Sons.
Inc, 1993.
5. Mikell P. Groover (2001). Automation, Production Systems, and Computer-Integrated Manufacturing,
2nded., Prentice-Hall of India Private Limited.
6. Bedworth, D.D., Henderson, M.R., and Wolfe, P.M., Computer-Integrated Design and Manufacturing,
McGraw-Hill International Edition, 1991.
7. Chang, T-C, Wysk, R.A., and Wang, H-P,Computer-Aided Manufacturing, 2nd ed., Prentice-Hall
International, Inc, 1998.
 ME4126 ENGINEERING OPTIMIZATION

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3

Module1 (10 hours)

Introduction – engineering applications of optimization, Statement of an optimization problem, Classification of
optimization problems, Linear Programming, Mathematical formulations, Graphical solution, Simplex method,
Artificial variable technique – M-method – two-phase method, Duality theory, Sensitivity analysis.
Module2 (10 hours)
Integer programming, Mathematical formulations, Zero-one problems – additive algorithm, Gomory’s cutting
plane algorithm, Branch and bound algorithm, All integer primal algorithm, All integer dual algorithm, Mixed
integer programming – cutting plane algorithm and Bender’s partitioning algorithm.
Module3 (10 hours)
Travelling Salesman Problem, Mathematical formulations, Branch and bound algorithms, Heuristics – nearest
neighbourhood algorithm – pairwise-interchange heuristic – three-opt heuristic – twice around the tree heuristic
and its performance, Vehicle routing problem – optimal solution and heuristic solutions, Network optimization
models, Terminology of networks, Minimum spanning tree problem, Shortest-path problem, Maximum flow
problem, Minimum cost flow problem, Network simplex method.
Module4 (12 hours)
Non-linear programming, Formulations, General non-linear programming problem, Unconstrained optimization
problem – necessary and sufficient conditions for extrema, Constrained optimization with equality constraints –
Lagrangean method, Constrained optimization with inequality constraints – Kuhn-Tucker conditions, Quadratic
programming – Wolfe’s modified Simplex method.
References
1. Srinivasan, G., Operations Research – principles and applications, 2nd ed., Prentice-Hall of India, New
Delhi, 2010.
2. Hillier, F.S., and Lieberman, G.J., Introduction to Operations Research, 8th ed., Tata McGraw-Hill, New
Delhi, 2010.
3. Ravindran A., Philips, D.T., and Solberg, J.J., Operations Research: Principles and Practice, 2nd ed., John
Wiley & Sons, 1987.
4. Taha, H.A., Operations Research: An introduction, 6th ed., Prentice-Hall of India, New Delhi, 1997.
5. Winston, W.L., Operations Research: Applications and Algorithms, Duxbury Press, 1993.
6. Rao, S.S., Optimization:Theory and Applications, 2nd ed., Wiley Eastern, 1994.
 ME4127 ACCOUNTING AND FINANCE FOR ENGINEERS

Prerequisite: Nil
L T P C
Total Hours: 42 hours
3 0 0 3
Module 1 (10 Hours)
Finance and related discipline – scope – function,Time value of money,Stocks and bond valuation, Sources of
corporate finance – capital market.
Module 2 (11 Hours)
Financial Accounting – need –concepts, Journal,Ledger,Trial balance, Profit and loss account – Construction,
Balance sheet – Construction – accounting equation, accounting softwares.
Module 3 (11 Hours)
Financial statement analysis – ratio analysis, Statement of changes in financial position, Working capital basis.
Module 4 (10 Hours)
Financial planning – budgeting - working capital computation,Capitalbudgeting – traditional and discounted
cash flow techniques –NPV – IRR comparisons
References
1. Khan M.Y. and Jain P.K., “Financial Management”, 3rd ed., Tata McGraw-Hill, 2003.
2. Jawahar Lal, “Financial Accounting”, 2nd ed., Wheeler publishing, 2000.
3. I.M. Pandey, “Financial Management”, 8th ed., Vikas publishing house, 2003.
4. Prasanna Chandra, “Financial Management”, 4th ed., Tata McGraw-Hill, 2003.
 ME4128 SIMULATION MODELLING AND ANALYSIS

Prerequisite: Nil
L T P C
Total Hours: 42 2 1 0 3
Module 1 (10 hours)
Systems and system environment, Components of a system, Discrete and continuous systems, Model of a
system, Types of models, Steps in simulation study, Technique of simulation, Comparison of simulation and
analytical methods, Monte Carlo simulation.
Module 2 (10 hours)
Simulation of queuing systems–simulation of inventory systems– concept in discrete event simulation, Random
number generation–techniques for generating random numbers, Test for random numbers – frequency tests and
tests for autocorrelation,Random variate generation –inverse transform method and acceptance rejection
technique.
Module 3 (10 hours)
Input modelling for simulation – data collection, Identifying the distribution with data, Parameter estimation,
Goodness of fit tests –chi square and kolmogorov smirnov tests, Verification and validation of simulation
models.
Module 4 (12 hours)
Output analysis for a single model – measures of performance and their estimation, Output analysis for
terminating simulations and steady state simulations. Introduction to simulation software – simulation model
building using ARENA and Excel.
References
1. Banks, J., Carson, J.S., Nelson, B.L., and Nicol, D.M., Discrete–Event System Simulation, Pearson
Education, Inc., 2007.
2. Law, A.M., and Kelton, W.D., Simulation Modelling and Analysis, McGraw Hill International, 2000.
3. Gordon, G., System Simulation, Second Edition, Prentice Hall of India, 1995.
4. Ross, S.M., Simulation, Third Edition, Academic Press, 2002.
5. Fishman, G.S., Concepts and Methods in discrete Event Digital Simulations, Wiley, New York, 1973.
6. Oakshott, L.,Business Modelling and Simulation, Pitman Publishing, 1997.
7. Carrie, A., Simulation of Manufacturing Systems, John Wiley & Sons Ltd., 1988.
8. Rossetti, M.D., Simulation Modeling and ARENA, John Wiley, 2009.
 ME4129 MODELLING OF MANUFACTURING SYSTEMS

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3
Module1 (8 hours)
Modelling automated manufacturing systems – role of performance modelling, Performance modelling tools –
simulation models and analytical models, Automated manufacturing systems – input-output model, Plant
configurations, Performance measures.
Module2 (12 hours)
Computer controlled machines – NC machines, Pallets and fixtures, Machining centers, Automated inspection
systems, Material handling systems – conveyors – industrial robots – automated guided vehicles – storageand
retrieval systems, Facility layout – CRAFT – quadratic assignment problem, Group technology – coding
schemes – production flow analysis – mathematical model, Flexible manufacturing systems – architecture of
FMS – automated workpiece flow – automated assembly systems – deadlocks – performance measures.
Module3 (10 hours)
Markov chain models, Geometric and exponential random variables, Stochastic processes – Poisson process,
Discrete-time Markov chains, Continuous-time Markov chains, Markov model of a transfer line, Birth and
death processes in manufacturing.
Module4 (12 hours)
Basic queuing models – (M/M/1) – (M/M/m),Queues with breakdowns, Analysis of a flexible manufacturing
center, Queuing networks – open – closed – productform, Queuing networks with blocking, Application of
queuing models for manufacturing systems – simulation models for serials lines and flexible manufacturing.
References
1. Viswanadham, N., and Narahari, Y., Performance modeling of automated manufacturing systems,
Prentice-Hallof India, New Delhi, 1996.
2. Askin, R.G., and Standridge, C.R., Modeling and Analysis of manufacturing systems, John Wiley&
Sons, 1993.
3. Altiok, T., Performance Analysis of Manufacturing Systems, Springer, 1997.
4. Brandimarte, P., and Villa, A., Performance modeling of automated manufacturing systems, Prentice-
Hall of India, New Delhi, 1996.
5. Curry, G.L., and Feldman, R.M., Manufacturing systems modeling and analysis, Springer, 2011.
 ME4130 HUMAN FACTORS IN ENGINEERING AND DESIGN

Prerequisite: Nil L T P C
3 0 0 3
Total Hours: 42 hours
Module 1 (10 Hours)
Human factors and Systems, Nature of man-machine systems and characteristics, Information input and
processing – information theory – displaying information – coding of information – mode of information
processing, Perception, Attention, Mental Workload, Human Factors in information revolution
Module 2 (10 Hours)
Test, Graphics, Symbols and Codes, Visual capabilities – visual display terminal screens and text, Graphic
representations, Symbolic designs – Quantitative visual displays – signals and warning lights, Representational
displays – auditory– tactual and Olfactory Displays – Cutaneous senses – Speech communication.
Module 3 (12 Hours)
Human motor activity, Muscle physiology, Measure of physiological strain – physical workload – strength and
endurance, Manual material handling, Recommended limits, Motor skills, Human control of systems.
Module 4 (10 Hours)
Anthropometry and work-space design – use of anthropometric data, Design of work surfaces – science of
seating, General location of control and displays within work space, Interpersonal aspects of workplace design.
References
1. Sanders, M.S., and McCormick, E.J., Human Factors in Engineering and design, 7th ed., McGraw-Hill
International.
2. Murrell, K.F.H., and Schnauber, H., Ergonomics. Econ, Munich, 1986.
3. Gavriel, S., Handbook of Human Factors & Ergonomics, Inter-science, 1997.
 ME3114 CAD/CAM/CIM

Prerequisite: Nil L T P C
Total Hours: 42 3 0 0 3

Module 1 (9 hours)
Introduction to computer graphics, 2D and 3D transformations, Plane and space curves, surface description and
generation, CAD/CAM hardware and software, CAD/CAM data exchange and integration.
Module 2 (11 hours)
CNC machine tools, fundamentals of CNC machine tools, constructional features, drives and controls, stepper
motors, servo motors, hydraulic systems, feed back devices, counting devices, interpolators linear, circular
interpolation and other emerging techniques, adaptive control systems for turning and milling.
Module 3 (11 hours)
CNC manual part programming and computer assisted programming, APT language, geometry, motion and
auxiliary statements, macro statements, post processors, CNC programming with interactive graphics, use of
various software packages, development of CNC programmes for special problems.
Module 4 (11 hours)
Computer integrated manufacturing systems, material handling and identification technologies, computer aided
inspection, group technology, flexible manufacturing systems, industrial robotics and machine vision, rapid
prototyping, design for manufacturability, process planning and concurrent engineering, lean production and
agile manufacturing.

References

1. David, F.Rogers.,&Adams,J.H.,Mathematical Elements of Computer Graphics, 15 th Reprint, McGraw

Hill International, 2008.
2. David, F., Rogers.,Procedural Elements for Computer Graphics, McGraw Hill International, 1998.
3. Ibrahim., Zeid.,CAD/CAM Theory and Practice, Tata McGraw Hill publishing company, 1991.
4. Yoram., Koren., Computer Control of Manufacturing Systems, Mc Graw Hill Book Company, 1983.
5. Mikell, P. Groover.,Automation, Production Systems, and Computer Integrated Manufacturing,
Pearson Education, 2008.
6. Mehta,N.K., Machine Tool Design & Numerical Control, 2 nd ed., Tata McGraw Hill, 2005.
7. Bolton. W., Mechatronics, Electronic Control Systems in Mechanical Engineering, Addison Wesley
Longman Limited, 2003.
8. HMT Limited, Mechatronics, 17 th Reprint, Tata McGraw Hill Publishing Company Limited, 2008.
9. Fu., K.S. Gonzalez., R.C., and Lee., C.S.G , Robotics, Control, Sensing, Vision and Intelligence,
McGraw Hill International, 1987